arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts

   1 // SPDX-License-Identifier: GPL-2.0-only
   2
   3 /dts-v1/;
   4
   5 #include "msm8916-pm8916.dtsi"
   6 #include <dt-bindings/gpio/gpio.h>
   7 #include <dt-bindings/input/input.h>
   8 #include <dt-bindings/interrupt-controller/irq.h>
   9 #include <dt-bindings/leds/common.h>
  10
  11 / {
  12         model = "Longcheer L8150";
  13         compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
  14
  15         aliases {
  16                 serial0 = &blsp1_uart2;
  17         };
  18
  19         chosen {
  20                 stdout-path = "serial0";
  21         };
  22
  23         reserved-memory {
  24                 // wcnss.mdt is not relocatable, so it must be loaded at 0x8b600000
  25                 /delete-node/ wcnss@89300000;
  26
  27                 wcnss_mem: wcnss@8b600000 {
  28                         reg = <0x0 0x8b600000 0x0 0x600000>;
  29                         no-map;
  30                 };
  31         };
  32
  33         // FIXME: Use extcon device provided by charger driver when available
  34         usb_vbus: usb-vbus {
  35                 compatible = "linux,extcon-usb-gpio";
  36                 vbus-gpio = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
  37                 pinctrl-names = "default";
  38                 pinctrl-0 = <&usb_vbus_default>;
  39         };
  40
  41         gpio-keys {
  42                 compatible = "gpio-keys";
  43
  44                 pinctrl-names = "default";
  45                 pinctrl-0 = <&gpio_keys_default>;
  46
  47                 label = "GPIO Buttons";
  48
  49                 volume-up {
  50                         label = "Volume Up";
  51                         gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
  52                         linux,code = <KEY_VOLUMEUP>;
  53                 };
  54         };
  55
  56         reg_ctp: regulator-ctp {
  57                 compatible = "regulator-fixed";
  58                 regulator-name = "ctp";
  59
  60                 regulator-min-microvolt = <2800000>;
  61                 regulator-max-microvolt = <2800000>;
  62
  63                 gpio = <&msmgpio 17 GPIO_ACTIVE_HIGH>;
  64                 enable-active-high;
  65
  66                 pinctrl-names = "default";
  67                 pinctrl-0 = <&ctp_pwr_en_default>;
  68         };
  69
  70         flash-led-controller {
  71                 compatible = "sgmicro,sgm3140";
  72                 flash-gpios = <&msmgpio 31 GPIO_ACTIVE_HIGH>;
  73                 enable-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
  74
  75                 pinctrl-names = "default";
  76                 pinctrl-0 = <&camera_flash_default>;
  77
  78                 flash_led: led {
  79                         function = LED_FUNCTION_FLASH;
  80                         color = <LED_COLOR_ID_WHITE>;
  81                         flash-max-timeout-us = <250000>;
  82                 };
  83         };
  84 };
  85
  86 &blsp_i2c1 {
  87         status = "okay";
  88
  89         led-controller@45 {
  90                 compatible = "awinic,aw2013";
  91                 reg = <0x45>;
  92                 #address-cells = <1>;
  93                 #size-cells = <0>;
  94
  95                 vcc-supply = <&pm8916_l17>;
  96
  97                 led@0 {
  98                         reg = <0>;
  99                         led-max-microamp = <5000>;
 100                         function = LED_FUNCTION_INDICATOR;
 101                         color = <LED_COLOR_ID_RED>;
 102                 };
 103
 104                 led@1 {
 105                         reg = <1>;
 106                         led-max-microamp = <5000>;
 107                         function = LED_FUNCTION_INDICATOR;
 108                         color = <LED_COLOR_ID_GREEN>;
 109                 };
 110
 111                 led@2 {
 112                         reg = <2>;
 113                         led-max-microamp = <5000>;
 114                         function = LED_FUNCTION_INDICATOR;
 115                         color = <LED_COLOR_ID_BLUE>;
 116                 };
 117         };
 118 };
 119
 120 &blsp_i2c2 {
 121         status = "okay";
 122
 123         accelerometer@10 {
 124                 compatible = "bosch,bmc150_accel";
 125                 reg = <0x10>;
 126
 127                 vdd-supply = <&pm8916_l17>;
 128                 vddio-supply = <&pm8916_l6>;
 129
 130                 mount-matrix = "0", "1", "0",
 131                               "-1", "0", "0",
 132                                "0", "0", "1";
 133         };
 134
 135         magnetometer@12 {
 136                 compatible = "bosch,bmc150_magn";
 137                 reg = <0x12>;
 138
 139                 vdd-supply = <&pm8916_l17>;
 140                 vddio-supply = <&pm8916_l6>;
 141         };
 142
 143         gyroscope@68 {
 144                 compatible = "bosch,bmg160";
 145                 reg = <0x68>;
 146
 147                 interrupt-parent = <&msmgpio>;
 148                 interrupts = <23 IRQ_TYPE_EDGE_RISING>;
 149
 150                 pinctrl-names = "default";
 151                 pinctrl-0 = <&gyro_int_default>;
 152
 153                 vdd-supply = <&pm8916_l17>;
 154                 vddio-supply = <&pm8916_l6>;
 155         };
 156 };
 157
 158 &blsp_i2c5 {
 159         status = "okay";
 160
 161         rmi4@20 {
 162                 compatible = "syna,rmi4-i2c";
 163                 reg = <0x20>;
 164                 #address-cells = <1>;
 165                 #size-cells = <0>;
 166
 167                 interrupt-parent = <&msmgpio>;
 168                 interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
 169
 170                 vdd-supply = <&reg_ctp>;
 171                 vio-supply = <&pm8916_l6>;
 172
 173                 pinctrl-names = "default";
 174                 pinctrl-0 = <&tp_int_default>;
 175
 176                 syna,startup-delay-ms = <10>;
 177
 178                 rmi4-f01@1 {
 179                         reg = <0x1>;
 180                         syna,nosleep-mode = <1>; // Allow sleeping
 181                 };
 182
 183                 rmi4-f12@12 {
 184                         reg = <0x12>;
 185                         syna,sensor-type = <1>; // Touchscreen
 186                 };
 187         };
 188 };
 189
 190 &blsp1_uart2 {
 191         status = "okay";
 192 };
 193
 194 &pm8916_resin {
 195         status = "okay";
 196         linux,code = <KEY_VOLUMEDOWN>;
 197 };
 198
 199 &pm8916_vib {
 200         status = "okay";
 201 };
 202
 203 &pronto {
 204         status = "okay";
 205 };
 206
 207 &sdhc_1 {
 208         status = "okay";
 209
 210         pinctrl-names = "default", "sleep";
 211         pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
 212         pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 213 };
 214
 215 &sdhc_2 {
 216         status = "okay";
 217
 218         pinctrl-names = "default", "sleep";
 219         pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
 220         pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
 221
 222         non-removable;
 223 };
 224
 225 &usb {
 226         status = "okay";
 227         dr_mode = "peripheral";
 228         extcon = <&usb_vbus>;
 229 };
 230
 231 &usb_hs_phy {
 232         extcon = <&usb_vbus>;
 233 };
 234
 235 &smd_rpm_regulators {
 236         vdd_l1_l2_l3-supply = <&pm8916_s3>;
 237         vdd_l4_l5_l6-supply = <&pm8916_s4>;
 238         vdd_l7-supply = <&pm8916_s4>;
 239
 240         s3 {
 241                 regulator-min-microvolt = <1200000>;
 242                 regulator-max-microvolt = <1300000>;
 243         };
 244
 245         s4 {
 246                 regulator-min-microvolt = <1800000>;
 247                 regulator-max-microvolt = <2100000>;
 248         };
 249
 250         l1 {
 251                 regulator-min-microvolt = <1225000>;
 252                 regulator-max-microvolt = <1225000>;
 253         };
 254
 255         l2 {
 256                 regulator-min-microvolt = <1200000>;
 257                 regulator-max-microvolt = <1200000>;
 258         };
 259
 260         l4 {
 261                 regulator-min-microvolt = <2050000>;
 262                 regulator-max-microvolt = <2050000>;
 263         };
 264
 265         l5 {
 266                 regulator-min-microvolt = <1800000>;
 267                 regulator-max-microvolt = <1800000>;
 268         };
 269
 270         l6 {
 271                 regulator-min-microvolt = <1800000>;
 272                 regulator-max-microvolt = <1800000>;
 273         };
 274
 275         l7 {
 276                 regulator-min-microvolt = <1800000>;
 277                 regulator-max-microvolt = <1800000>;
 278         };
 279
 280         l8 {
 281                 regulator-min-microvolt = <2850000>;
 282                 regulator-max-microvolt = <2900000>;
 283         };
 284
 285         l9 {
 286                 regulator-min-microvolt = <3300000>;
 287                 regulator-max-microvolt = <3300000>;
 288         };
 289
 290         l10 {
 291                 regulator-min-microvolt = <2700000>;
 292                 regulator-max-microvolt = <2800000>;
 293         };
 294
 295         l11 {
 296                 regulator-min-microvolt = <1800000>;
 297                 regulator-max-microvolt = <2950000>;
 298                 regulator-allow-set-load;
 299                 regulator-system-load = <200000>;
 300         };
 301
 302         l12 {
 303                 regulator-min-microvolt = <1800000>;
 304                 regulator-max-microvolt = <2950000>;
 305         };
 306
 307         l13 {
 308                 regulator-min-microvolt = <3075000>;
 309                 regulator-max-microvolt = <3075000>;
 310         };
 311
 312         l14 {
 313                 regulator-min-microvolt = <1800000>;
 314                 regulator-max-microvolt = <3300000>;
 315         };
 316
 317         l15 {
 318                 regulator-min-microvolt = <1800000>;
 319                 regulator-max-microvolt = <3300000>;
 320         };
 321
 322         l16 {
 323                 regulator-min-microvolt = <1800000>;
 324                 regulator-max-microvolt = <3300000>;
 325         };
 326
 327         l17 {
 328                 regulator-min-microvolt = <2850000>;
 329                 regulator-max-microvolt = <2850000>;
 330         };
 331
 332         l18 {
 333                 regulator-min-microvolt = <2700000>;
 334                 regulator-max-microvolt = <2700000>;
 335         };
 336 };
 337
 338 &msmgpio {
 339         camera_flash_default: camera-flash-default {
 340                 pins = "gpio31", "gpio32";
 341                 function = "gpio";
 342
 343                 drive-strength = <2>;
 344                 bias-disable;
 345         };
 346
 347         ctp_pwr_en_default: ctp-pwr-en-default {
 348                 pins = "gpio17";
 349                 function = "gpio";
 350
 351                 drive-strength = <2>;
 352                 bias-disable;
 353         };
 354
 355         gpio_keys_default: gpio-keys-default {
 356                 pins = "gpio107";
 357                 function = "gpio";
 358
 359                 drive-strength = <2>;
 360                 bias-pull-up;
 361         };
 362
 363         gyro_int_default: gyro-int-default {
 364                 pins = "gpio23";
 365                 function = "gpio";
 366
 367                 drive-strength = <2>;
 368                 bias-disable;
 369         };
 370
 371         tp_int_default: tp-int-default {
 372                 pins = "gpio13";
 373                 function = "gpio";
 374
 375                 drive-strength = <2>;
 376                 bias-disable;
 377         };
 378
 379         usb_vbus_default: usb-vbus-default {
 380                 pins = "gpio62";
 381                 function = "gpio";
 382
 383                 bias-pull-up;
 384         };
 385 };