arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts

   1 // SPDX-License-Identifier: GPL-2.0-only
   2
   3 /dts-v1/;
   4
   5 #include "msm8916-pm8916.dtsi"
   6 #include "msm8916-modem-qdsp6.dtsi"
   7
   8 #include <dt-bindings/gpio/gpio.h>
   9 #include <dt-bindings/input/input.h>
  10 #include <dt-bindings/interrupt-controller/irq.h>
  11 #include <dt-bindings/leds/common.h>
  12
  13 / {
  14         model = "Longcheer L8150";
  15         compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
  16         chassis-type = "handset";
  17
  18         aliases {
  19                 mmc0 = &sdhc_1; /* eMMC */
  20                 mmc1 = &sdhc_2; /* SD card */
  21                 serial0 = &blsp_uart2;
  22         };
  23
  24         chosen {
  25                 stdout-path = "serial0";
  26         };
  27
  28         /*
  29          * For some reason, the signed wcnss firmware is not relocatable.
  30          * It must be loaded at 0x8b600000. Unfortunately, this also means that
  31          * mpss_mem does not fit when loaded to the typical address at 0x86800000.
  32          *
  33          * Load wcnss_mem to the fixed address and relocate mpss_mem to the next
  34          * working higher address. For some reason the modem firmware does not
  35          * boot when placed at 0x8a800000 to 0x8e800000.
  36          */
  37         reserved-memory {
  38                 /delete-node/ mpss@86800000;
  39                 /delete-node/ wcnss;
  40
  41                 wcnss_mem: wcnss@8b600000 {
  42                         reg = <0x0 0x8b600000 0x0 0x600000>;
  43                         no-map;
  44                 };
  45
  46                 mpss_mem: mpss@8e800000 {
  47                         reg = <0x0 0x8e800000 0x0 0x5000000>;
  48                         no-map;
  49                 };
  50         };
  51
  52         battery: battery {
  53                 compatible = "simple-battery";
  54                 voltage-min-design-microvolt = <3400000>;
  55                 voltage-max-design-microvolt = <4350000>;
  56                 energy-full-design-microwatt-hours = <9500000>;
  57                 charge-full-design-microamp-hours = <2500000>;
  58
  59                 ocv-capacity-celsius = <25>;
  60                 ocv-capacity-table-0 = <4330000 100>, <4265000 95>,
  61                         <4208000 90>, <4153000 85>, <4100000 80>, <4049000 75>,
  62                         <4001000 70>, <3962000 65>, <3919000 60>, <3872000 55>,
  63                         <3839000 50>, <3817000 45>, <3798000 40>, <3783000 35>,
  64                         <3767000 30>, <3747000 25>, <3729000 20>, <3709000 16>,
  65                         <3688000 13>, <3681000 11>, <3680000 10>, <3679000 9>,
  66                         <3677000 8>, <3674000 7>, <3666000 6>, <3641000 5>,
  67                         <3597000 4>, <3537000 3>, <3457000 2>, <3336000 1>,
  68                         <3000000 0>;
  69         };
  70
  71         gpio-keys {
  72                 compatible = "gpio-keys";
  73
  74                 pinctrl-names = "default";
  75                 pinctrl-0 = <&gpio_keys_default>;
  76
  77                 label = "GPIO Buttons";
  78
  79                 button-volume-up {
  80                         label = "Volume Up";
  81                         gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
  82                         linux,code = <KEY_VOLUMEUP>;
  83                 };
  84         };
  85
  86         reg_ctp: regulator-ctp {
  87                 compatible = "regulator-fixed";
  88                 regulator-name = "ctp";
  89
  90                 regulator-min-microvolt = <2800000>;
  91                 regulator-max-microvolt = <2800000>;
  92
  93                 gpio = <&tlmm 17 GPIO_ACTIVE_HIGH>;
  94                 enable-active-high;
  95
  96                 pinctrl-names = "default";
  97                 pinctrl-0 = <&ctp_pwr_en_default>;
  98         };
  99
 100         flash-led-controller {
 101                 compatible = "sgmicro,sgm3140";
 102                 flash-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
 103                 enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
 104
 105                 pinctrl-names = "default";
 106                 pinctrl-0 = <&camera_flash_default>;
 107
 108                 flash_led: led {
 109                         function = LED_FUNCTION_FLASH;
 110                         color = <LED_COLOR_ID_WHITE>;
 111                         flash-max-timeout-us = <250000>;
 112                 };
 113         };
 114 };
 115
 116 &blsp_i2c1 {
 117         status = "okay";
 118
 119         led-controller@45 {
 120                 compatible = "awinic,aw2013";
 121                 reg = <0x45>;
 122                 #address-cells = <1>;
 123                 #size-cells = <0>;
 124
 125                 vcc-supply = <&pm8916_l17>;
 126                 vio-supply = <&pm8916_l6>;
 127
 128                 led@0 {
 129                         reg = <0>;
 130                         led-max-microamp = <5000>;
 131                         function = LED_FUNCTION_INDICATOR;
 132                         color = <LED_COLOR_ID_RED>;
 133                 };
 134
 135                 led@1 {
 136                         reg = <1>;
 137                         led-max-microamp = <5000>;
 138                         function = LED_FUNCTION_INDICATOR;
 139                         color = <LED_COLOR_ID_GREEN>;
 140                 };
 141
 142                 led@2 {
 143                         reg = <2>;
 144                         led-max-microamp = <5000>;
 145                         function = LED_FUNCTION_INDICATOR;
 146                         color = <LED_COLOR_ID_BLUE>;
 147                 };
 148         };
 149 };
 150
 151 &blsp_i2c2 {
 152         status = "okay";
 153
 154         accelerometer@10 {
 155                 compatible = "bosch,bmc156_accel";
 156                 reg = <0x10>;
 157
 158                 /*
 159                  * For some reason the interrupt line is usually not connected
 160                  * to the BMC156. However, there are two pads next to the chip
 161                  * that can be shorted to make it work if needed.
 162                  *
 163                  * interrupt-parent = <&tlmm>;
 164                  * interrupts = <116 IRQ_TYPE_EDGE_RISING>;
 165                  */
 166
 167                 pinctrl-names = "default";
 168                 pinctrl-0 = <&accel_int_default>;
 169
 170                 vdd-supply = <&pm8916_l17>;
 171                 vddio-supply = <&pm8916_l6>;
 172
 173                 mount-matrix = "0", "1", "0",
 174                               "-1", "0", "0",
 175                                "0", "0", "1";
 176         };
 177
 178         magnetometer@12 {
 179                 compatible = "bosch,bmc156_magn";
 180                 reg = <0x12>;
 181
 182                 interrupt-parent = <&tlmm>;
 183                 interrupts = <113 IRQ_TYPE_EDGE_RISING>;
 184
 185                 pinctrl-names = "default";
 186                 pinctrl-0 = <&magn_int_default>;
 187
 188                 vdd-supply = <&pm8916_l17>;
 189                 vddio-supply = <&pm8916_l6>;
 190         };
 191
 192         light-sensor@23 {
 193                 compatible = "liteon,ltr559";
 194                 reg = <0x23>;
 195                 proximity-near-level = <75>;
 196
 197                 interrupt-parent = <&tlmm>;
 198                 interrupts = <115 IRQ_TYPE_EDGE_FALLING>;
 199
 200                 pinctrl-names = "default";
 201                 pinctrl-0 = <&light_int_default>;
 202
 203                 vdd-supply = <&pm8916_l17>;
 204                 vddio-supply = <&pm8916_l6>;
 205         };
 206
 207         gyroscope@68 {
 208                 compatible = "bosch,bmg160";
 209                 reg = <0x68>;
 210
 211                 interrupt-parent = <&tlmm>;
 212                 interrupts = <23 IRQ_TYPE_EDGE_RISING>,
 213                              <22 IRQ_TYPE_EDGE_RISING>;
 214
 215                 pinctrl-names = "default";
 216                 pinctrl-0 = <&gyro_int_default>;
 217
 218                 vdd-supply = <&pm8916_l17>;
 219                 vddio-supply = <&pm8916_l6>;
 220         };
 221 };
 222
 223 &blsp_i2c5 {
 224         status = "okay";
 225
 226         rmi4@20 {
 227                 compatible = "syna,rmi4-i2c";
 228                 reg = <0x20>;
 229                 #address-cells = <1>;
 230                 #size-cells = <0>;
 231
 232                 interrupt-parent = <&tlmm>;
 233                 interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
 234
 235                 vdd-supply = <&reg_ctp>;
 236                 vio-supply = <&pm8916_l6>;
 237
 238                 pinctrl-names = "default";
 239                 pinctrl-0 = <&tp_int_default>;
 240
 241                 syna,startup-delay-ms = <10>;
 242
 243                 rmi4-f01@1 {
 244                         reg = <0x1>;
 245                         syna,nosleep-mode = <1>; /* Allow sleeping */
 246                 };
 247
 248                 rmi4-f12@12 {
 249                         reg = <0x12>;
 250                         syna,sensor-type = <1>; /* Touchscreen */
 251                 };
 252         };
 253 };
 254
 255 &blsp_uart2 {
 256         status = "okay";
 257 };
 258
 259 &pm8916_bms {
 260         status = "okay";
 261
 262         monitored-battery = <&battery>;
 263         power-supplies = <&pm8916_charger>;
 264 };
 265
 266 &pm8916_charger {
 267         status = "okay";
 268
 269         monitored-battery = <&battery>;
 270
 271         qcom,fast-charge-safe-current = <900000>;
 272         qcom,fast-charge-safe-voltage = <4300000>;
 273 };
 274
 275 &pm8916_codec {
 276         qcom,micbias-lvl = <2800>;
 277         qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
 278         qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
 279         qcom,hphl-jack-type-normally-open;
 280 };
 281
 282 &pm8916_resin {
 283         status = "okay";
 284         linux,code = <KEY_VOLUMEDOWN>;
 285 };
 286
 287 &pm8916_rpm_regulators {
 288         pm8916_l17: l17 {
 289                 regulator-min-microvolt = <2850000>;
 290                 regulator-max-microvolt = <2850000>;
 291         };
 292 };
 293
 294 &pm8916_vib {
 295         status = "okay";
 296 };
 297
 298 &sdhc_1 {
 299         status = "okay";
 300 };
 301
 302 &sdhc_2 {
 303         status = "okay";
 304         non-removable;
 305 };
 306
 307 &sound {
 308         audio-routing =
 309                 "AMIC1", "MIC BIAS Internal1",
 310                 "AMIC2", "MIC BIAS Internal2",
 311                 "AMIC3", "MIC BIAS Internal3";
 312 };
 313
 314 &usb {
 315         status = "okay";
 316         dr_mode = "peripheral";
 317         extcon = <&pm8916_charger>;
 318 };
 319
 320 &usb_hs_phy {
 321         extcon = <&pm8916_charger>;
 322 };
 323
 324 &venus {
 325         status = "okay";
 326 };
 327
 328 &venus_mem {
 329         status = "okay";
 330 };
 331
 332 &wcnss {
 333         status = "okay";
 334 };
 335
 336 &wcnss_iris {
 337         compatible = "qcom,wcn3620";
 338 };
 339
 340 &wcnss_mem {
 341         status = "okay";
 342 };
 343
 344 &tlmm {
 345         accel_int_default: accel-int-default-state {
 346                 pins = "gpio116";
 347                 function = "gpio";
 348
 349                 drive-strength = <2>;
 350                 bias-disable;
 351         };
 352
 353         camera_flash_default: camera-flash-default-state {
 354                 pins = "gpio31", "gpio32";
 355                 function = "gpio";
 356
 357                 drive-strength = <2>;
 358                 bias-disable;
 359         };
 360
 361         ctp_pwr_en_default: ctp-pwr-en-default-state {
 362                 pins = "gpio17";
 363                 function = "gpio";
 364
 365                 drive-strength = <2>;
 366                 bias-disable;
 367         };
 368
 369         gpio_keys_default: gpio-keys-default-state {
 370                 pins = "gpio107";
 371                 function = "gpio";
 372
 373                 drive-strength = <2>;
 374                 bias-pull-up;
 375         };
 376
 377         gyro_int_default: gyro-int-default-state {
 378                 pins = "gpio22", "gpio23";
 379                 function = "gpio";
 380
 381                 drive-strength = <2>;
 382                 bias-disable;
 383         };
 384
 385         light_int_default: light-int-default-state {
 386                 pins = "gpio115";
 387                 function = "gpio";
 388
 389                 drive-strength = <2>;
 390                 bias-disable;
 391         };
 392
 393         magn_int_default: magn-int-default-state {
 394                 pins = "gpio113";
 395                 function = "gpio";
 396
 397                 drive-strength = <2>;
 398                 bias-disable;
 399         };
 400
 401         tp_int_default: tp-int-default-state {
 402                 pins = "gpio13";
 403                 function = "gpio";
 404
 405                 drive-strength = <2>;
 406                 bias-disable;
 407         };
 408 };