-// SPDX-License-Identifier: (GPL-2.0+)
+// SPDX-License-Identifier: GPL-2.0+
/*
- * Copyright (C) 2015 DH electronics GmbH
+ * Copyright (C) 2015-2021 DH electronics GmbH
* Copyright (C) 2018 Marek Vasut <marex@denx.de>
*/
};
clk_ext_audio_codec: clock-codec {
- compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24000000>;
+ compatible = "fixed-clock";
};
display_bl: display-bl {
- compatible = "pwm-backlight";
- pwms = <&pwm1 0 50000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+ compatible = "pwm-backlight";
default-brightness-level = <8>;
- enable-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; /* GPIO G */
+ pwms = <&pwm1 0 50000 PWM_POLARITY_INVERTED>;
status = "okay";
};
lcd_display: disp0 {
- compatible = "fsl,imx-parallel-display";
#address-cells = <1>;
#size-cells = <0>;
+ compatible = "fsl,imx-parallel-display";
interface-pix-fmt = "rgb24";
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ipu1_lcdif &pinctrl_dhcom_g>;
+ pinctrl-names = "default";
status = "okay";
port@0 {
compatible = "gpio-keys";
button-0 {
+ gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* GPIO A */
label = "TA1-GPIO-A";
linux,code = <KEY_A>;
- gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pinctrl_dhcom_a>;
pinctrl-names = "default";
wakeup-source;
};
button-1 {
+ gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* GPIO B */
label = "TA2-GPIO-B";
linux,code = <KEY_B>;
- gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pinctrl_dhcom_b>;
pinctrl-names = "default";
wakeup-source;
};
button-2 {
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; /* GPIO C */
label = "TA3-GPIO-C";
linux,code = <KEY_C>;
- gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pinctrl_dhcom_c>;
pinctrl-names = "default";
wakeup-source;
};
button-3 {
+ gpios = <&gpio6 3 GPIO_ACTIVE_LOW>; /* GPIO D */
label = "TA4-GPIO-D";
linux,code = <KEY_D>;
- gpios = <&gpio6 3 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pinctrl_dhcom_d>;
pinctrl-names = "default";
wakeup-source;
*/
led-5 {
color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
function = LED_FUNCTION_INDICATOR;
gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* GPIO E */
- default-state = "off";
pinctrl-0 = <&pinctrl_dhcom_e>;
pinctrl-names = "default";
status = "disabled";
led-6 {
color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
function = LED_FUNCTION_INDICATOR;
gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>; /* GPIO F */
- default-state = "off";
pinctrl-0 = <&pinctrl_dhcom_f>;
pinctrl-names = "default";
};
led-7 {
color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
function = LED_FUNCTION_INDICATOR;
gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* GPIO H */
- default-state = "off";
pinctrl-0 = <&pinctrl_dhcom_h>;
pinctrl-names = "default";
};
led-8 {
color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
function = LED_FUNCTION_INDICATOR;
gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
- default-state = "off";
pinctrl-0 = <&pinctrl_dhcom_i>;
pinctrl-names = "default";
};
};
panel {
- compatible = "edt,etm0700g0edh6";
backlight = <&display_bl>;
+ compatible = "edt,etm0700g0edh6";
port {
lcd_panel_in: endpoint {
};
sound {
- compatible = "fsl,imx-audio-sgtl5000";
- model = "imx-sgtl5000";
- ssi-controller = <&ssi1>;
audio-codec = <&sgtl5000>;
audio-routing =
"MIC_IN", "Mic Jack",
"Mic Jack", "Mic Bias",
"LINE_IN", "Line In Jack",
"Headphone Jack", "HP_OUT";
- mux-int-port = <1>;
+ compatible = "fsl,imx-audio-sgtl5000";
+ model = "imx-sgtl5000";
mux-ext-port = <3>;
+ mux-int-port = <1>;
+ ssi-controller = <&ssi1>;
};
};
&audmux {
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux_ext>;
+ pinctrl-names = "default";
status = "okay";
};
&fec {
phy-mode = "rgmii";
phy-handle = <ðphy7>;
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet_1G>;
+ pinctrl-names = "default";
status = "okay";
mdio {
pinctrl-0 = <&pinctrl_ethphy7>;
pinctrl-names = "default";
reg = <7>;
- reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
reset-assert-us = <1000>;
reset-deassert-us = <1000>;
+ reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
rxc-skew-ps = <3000>;
rxd0-skew-ps = <0>;
rxd1-skew-ps = <0>;
rxd2-skew-ps = <0>;
rxd3-skew-ps = <0>;
+ rxdv-skew-ps = <0>;
txc-skew-ps = <3000>;
txd0-skew-ps = <0>;
txd1-skew-ps = <0>;
txd2-skew-ps = <0>;
txd3-skew-ps = <0>;
- rxdv-skew-ps = <0>;
txen-skew-ps = <0>;
};
};
&i2c2 {
sgtl5000: codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
#sound-dai-cells = <0>;
clocks = <&clk_ext_audio_codec>;
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
VDDA-supply = <®_3p3v>;
VDDIO-supply = <&sw2_reg>;
};
touchscreen@38 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_dhcom_e>;
compatible = "edt,edt-ft5406";
- reg = <0x38>;
interrupt-parent = <&gpio4>;
interrupts = <5 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+ pinctrl-0 = <&pinctrl_dhcom_e>;
+ pinctrl-names = "default";
+ reg = <0x38>;
};
};
&pcie {
pinctrl-0 = <&pinctrl_pcie &pinctrl_dhcom_j>;
- reset-gpio = <&gpio6 14 GPIO_ACTIVE_LOW>;
+ reset-gpio = <&gpio6 14 GPIO_ACTIVE_LOW>; /* GPIO J */
status = "okay";
};
&pwm1 {
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
+ pinctrl-names = "default";
status = "okay";
};
status = "okay";
};
-&usdhc3 {
+&usdhc3 { /* Micro SD card on module */
status = "okay";
};
&iomuxc {
- pinctrl-names = "default";
pinctrl-0 = <
/*
* The following DHCOM GPIOs are used on this board.
&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
>;
+ pinctrl-names = "default";
pinctrl_audmux_ext: audmux-ext-grp {
fsl,pins = <
- MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
>;
};
pinctrl_enet_1G: enet-1G-grp {
fsl,pins = <
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0
>;
};
pinctrl_ethphy7: ethphy7-grp {
fsl,pins = <
+ MX6QDL_PAD_EIM_D26__GPIO3_IO26 0xb1 /* WOL */
MX6QDL_PAD_EIM_D29__GPIO3_IO29 0xb0 /* Reset */
MX6QDL_PAD_GPIO_0__GPIO1_IO00 0xb1 /* Int */
- MX6QDL_PAD_EIM_D26__GPIO3_IO26 0xb1 /* WOL */
>;
};
pinctrl_ipu1_lcdif: ipu1-lcdif-grp {
fsl,pins = <
MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x38
- MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x38
MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x38
MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x38
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x38
MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x38
MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x38
MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x38
-// SPDX-License-Identifier: (GPL-2.0+)
+// SPDX-License-Identifier: GPL-2.0+
/*
- * Copyright (C) 2015 DH electronics GmbH
+ * Copyright (C) 2015-2021 DH electronics GmbH
* Copyright (C) 2018 Marek Vasut <marex@denx.de>
*/
serial4 = &uart3;
};
- memory@10000000 {
+ memory@10000000 { /* Appropriate memory size will be filled by U-Boot */
device_type = "memory";
reg = <0x10000000 0x20000000>;
};
+ reg_3p3v: regulator-3P3V {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "3P3V";
+ };
+
reg_eth_vio: regulator-eth-vio {
compatible = "regulator-fixed";
- gpio = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ gpio = <&gpio1 7 0>;
pinctrl-0 = <&pinctrl_enet_vio>;
pinctrl-names = "default";
regulator-always-on;
regulator-name = "latch_oe_on";
};
- reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ reg_usb_h1_vbus: regulator-usb-h1-vbus {
compatible = "regulator-fixed";
- regulator-name = "usb_otg_vbus";
+ enable-active-high;
+ gpio = <&gpio3 31 0>;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
+ regulator-name = "usb_h1_vbus";
};
- reg_usb_h1_vbus: regulator-usb-h1-vbus {
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
compatible = "regulator-fixed";
- regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_3p3v: regulator-3P3V {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
+ regulator-name = "usb_otg_vbus";
};
};
&can1 {
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexcan1>;
+ pinctrl-names = "default";
};
+/*
+ * Special hardware required which uses the pins from micro SD card. The pins
+ * SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2 Tx
+ * and Rx are output on DHCOM uart1 rts/cts pins. So to enable can2 on the board
+ * device tree file, you also need to disable the micro SD card and the uart1
+ * rts/cts have to be disabled or output on other DHCOM pins.
+ */
&can2 {
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexcan2>;
+ pinctrl-names = "default";
};
&ecspi1 {
cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio4 11 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
+ pinctrl-names = "default";
status = "okay";
- flash@0 { /* S25FL116K */
+ flash@0 { /* S25FL116K */
#address-cells = <1>;
#size-cells = <1>;
compatible = "jedec,spi-nor";
- spi-max-frequency = <50000000>;
- reg = <0>;
m25p,fast-read;
+ reg = <0>;
+ spi-max-frequency = <50000000>;
};
};
&ecspi2 {
cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
+ pinctrl-names = "default";
status = "okay";
};
&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet_100M>;
phy-mode = "rmii";
phy-handle = <ðphy0>;
+ pinctrl-0 = <&pinctrl_enet_100M>;
+ pinctrl-names = "default";
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
- ethphy0: ethernet-phy@0 { /* SMSC LAN8710Ai */
+ ethphy0: ethernet-phy@0 { /* SMSC LAN8710Ai */
compatible = "ethernet-phy-ieee802.3-c22";
interrupt-parent = <&gpio4>;
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
- max-speed = <100>;
pinctrl-0 = <&pinctrl_ethphy0>;
pinctrl-names = "default";
reg = <0>;
- reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
reset-assert-us = <1000>;
reset-deassert-us = <1000>;
+ reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
smsc,disable-energy-detect; /* Make plugin detection reliable */
};
};
};
&i2c1 {
+ /*
+ * Info: According to erratum ERR007805 clock frequency limit is 375000.
+ * The erratum for i.MX6S/DL is here [1] and for i.MX6Q/D is here [2].
+ * [1] https://www.nxp.com/docs/en/errata/IMX6SDLCE.pdf
+ * [2] https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
+ */
clock-frequency = <100000>;
- pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ pinctrl-names = "default", "gpio";
scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
};
&i2c2 {
+ /* Info: Clock frequency limit is 375000 (for details see i2c1) */
clock-frequency = <100000>;
- pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>;
pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ pinctrl-names = "default", "gpio";
scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
};
&i2c3 {
+ /* Info: Clock frequency limit is 375000 (for details see i2c1) */
clock-frequency = <100000>;
- pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c3>;
pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ pinctrl-names = "default", "gpio";
scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
ltc3676: pmic@3c {
compatible = "lltc,ltc3676";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pmic_hw300>;
- reg = <0x3c>;
interrupt-parent = <&gpio5>;
interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-names = "default";
+ reg = <0x3c>;
regulators {
sw1_reg: sw1 {
- regulator-min-microvolt = <787500>;
- regulator-max-microvolt = <1527272>;
lltc,fb-voltage-divider = <100000 110000>;
- regulator-suspend-mem-microvolt = <1040000>;
- regulator-ramp-delay = <7000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1527272>;
+ regulator-min-microvolt = <787500>;
+ regulator-ramp-delay = <7000>;
+ regulator-suspend-mem-microvolt = <1040000>;
};
sw2_reg: sw2 {
- regulator-min-microvolt = <1885714>;
- regulator-max-microvolt = <3657142>;
lltc,fb-voltage-divider = <100000 28000>;
- regulator-ramp-delay = <7000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3657142>;
+ regulator-min-microvolt = <1885714>;
+ regulator-ramp-delay = <7000>;
};
sw3_reg: sw3 {
- regulator-min-microvolt = <787500>;
- regulator-max-microvolt = <1527272>;
lltc,fb-voltage-divider = <100000 110000>;
- regulator-suspend-mem-microvolt = <980000>;
- regulator-ramp-delay = <7000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1527272>;
+ regulator-min-microvolt = <787500>;
+ regulator-ramp-delay = <7000>;
+ regulator-suspend-mem-microvolt = <980000>;
};
sw4_reg: sw4 {
- regulator-min-microvolt = <855571>;
- regulator-max-microvolt = <1659291>;
lltc,fb-voltage-divider = <100000 93100>;
- regulator-ramp-delay = <7000>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1659291>;
+ regulator-min-microvolt = <855571>;
+ regulator-ramp-delay = <7000>;
};
ldo1_reg: ldo1 {
- regulator-min-microvolt = <3240306>;
- regulator-max-microvolt = <3240306>;
lltc,fb-voltage-divider = <102000 29400>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3240306>;
+ regulator-min-microvolt = <3240306>;
};
ldo2_reg: ldo2 {
- regulator-min-microvolt = <2484708>;
- regulator-max-microvolt = <2484708>;
lltc,fb-voltage-divider = <100000 41200>;
- regulator-boot-on;
regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <2484708>;
+ regulator-min-microvolt = <2484708>;
};
};
};
- touchscreen@49 { /* TSC2004 */
+ touchscreen@49 { /* TSC2004 */
compatible = "ti,tsc2004";
+ interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-0 = <&pinctrl_tsc2004>;
+ pinctrl-names = "default";
reg = <0x49>;
vio-supply = <®_3p3v>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_tsc2004_hw300>;
- interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>;
status = "disabled";
};
eeprom@50 {
compatible = "atmel,24c02";
- reg = <0x50>;
pagesize = <16>;
+ reg = <0x50>;
};
rtc_i2c: rtc@56 {
compatible = "microcrystal,rv3029";
+ interrupt-parent = <&gpio7>;
+ interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-0 = <&pinctrl_rtc>;
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_rtc_hw300>;
reg = <0x56>;
- interrupt-parent = <&gpio7>;
- interrupts = <12 2>;
};
};
&pcie {
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie>;
+ pinctrl-names = "default";
};
®_arm {
vin-supply = <&sw3_reg>;
};
-®_soc {
+®_pu {
vin-supply = <&sw1_reg>;
};
-®_pu {
+®_soc {
vin-supply = <&sw1_reg>;
};
vin-supply = <&sw2_reg>;
};
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- uart-has-rtscts;
- dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
- dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+&uart1 { /* DHCOM UART1 */
dcd-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+ dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+ dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
rng-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pinctrl_uart1>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
status = "okay";
};
-&uart4 {
- pinctrl-names = "default";
+&uart4 { /* DHCOM UART3 */
pinctrl-0 = <&pinctrl_uart4>;
+ pinctrl-names = "default";
status = "okay";
};
-&uart5 {
- pinctrl-names = "default";
+&uart5 { /* DHCOM UART2 */
pinctrl-0 = <&pinctrl_uart5>;
+ pinctrl-names = "default";
uart-has-rtscts;
status = "okay";
};
&usbh1 {
- pinctrl-names = "default";
+ dr_mode = "host";
pinctrl-0 = <&pinctrl_usbh1>;
+ pinctrl-names = "default";
vbus-supply = <®_usb_h1_vbus>;
- dr_mode = "host";
status = "okay";
};
&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
dr_mode = "otg";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ pinctrl-names = "default";
+ vbus-supply = <®_usb_otg_vbus>;
status = "okay";
};
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
+&usdhc2 { /* External SD card via DHCOM */
cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
keep-power-in-suspend;
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-names = "default";
status = "okay";
};
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
+&usdhc3 { /* Micro SD card on module */
cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
fsl,wp-controller;
keep-power-in-suspend;
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-names = "default";
status = "disabled";
};
-&usdhc4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc4>;
- non-removable;
+&usdhc4 { /* eMMC on module */
bus-width = <8>;
- no-1-8-v;
keep-power-in-suspend;
+ no-1-8-v;
+ non-removable;
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ pinctrl-names = "default";
status = "okay";
};
#address-cells = <2>;
#size-cells = <1>;
fsl,weim-cs-gpr = <&gpr>;
- pinctrl-names = "default";
pinctrl-0 = <&pinctrl_weim &pinctrl_weim_cs0 &pinctrl_weim_cs1>;
+ pinctrl-names = "default";
/* It is necessary to setup 2x 64MB otherwise setting gpr fails */
ranges = <0 0 0x08000000 0x04000000>, /* CS0 */
<1 0 0x0c000000 0x04000000>; /* CS1 */
};
&iomuxc {
- pinctrl-names = "default";
pinctrl-0 = <
&pinctrl_hog_base
&pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
>;
+ pinctrl-names = "default";
pinctrl_hog_base: hog-base-grp {
fsl,pins = <
- MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x120b0
- MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x120b0
- MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x120b0
+ /* GPIOs for memory coding */
MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x120b0
MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x120b0
+ /* GPIOs for hardware coding */
+ MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x120b0
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x120b0
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x120b0
>;
};
pinctrl_ecspi1: ecspi1-grp {
fsl,pins = <
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
>;
pinctrl_ecspi2: ecspi2-grp {
fsl,pins = <
- MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x100b1
- MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x100b1
MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x100b1
MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x1b0b0
>;
};
pinctrl_enet_100M: enet-100M-grp {
fsl,pins = <
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
pinctrl_flexcan1: flexcan1-grp {
fsl,pins = <
- MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0
MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0
>;
};
>;
};
- pinctrl_pmic_hw300: pmic-hw300-grp {
+ pinctrl_pcie: pcie-grp {
fsl,pins = <
- MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1B0B0
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b1 /* Wake */
>;
};
- pinctrl_rtc_hw300: rtc-hw300-grp {
+ pinctrl_pmic: pmic-grp {
fsl,pins = <
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x120B0
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0
>;
};
- pinctrl_tsc2004_hw300: tsc2004-hw300-grp {
+ pinctrl_rtc: rtc-grp {
fsl,pins = <
- MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x120B0
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x120b0
>;
};
- pinctrl_pcie: pcie-grp {
+ pinctrl_tsc2004: tsc2004-grp {
fsl,pins = <
- MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b1 /* Wake */
+ MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x120b0
>;
};
pinctrl_uart1: uart1-grp {
fsl,pins = <
- MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
- MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x1b0b1
MX6QDL_PAD_EIM_D19__UART1_CTS_B 0x4001b0b1
+ MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x1b0b1
MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x4001b0b1
MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x4001b0b1
MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x4001b0b1
MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x4001b0b1
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
>;
};
pinctrl_usbh1: usbh1-grp {
fsl,pins = <
- MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x120B0
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x120b0
>;
};
pinctrl_usdhc2: usdhc2-grp {
fsl,pins = <
- MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x120b0
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
- MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x120B0
>;
};
pinctrl_usdhc3: usdhc3-grp {
fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
- MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x120B0
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x120b0
>;
};
pinctrl_usdhc4: usdhc4-grp {
fsl,pins = <
- MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
pinctrl_weim: weim-grp {
fsl,pins = <
+ MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0a6
+ MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0a6
+ MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0a6
+ MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0a6
+ MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0a6
+ MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0a6
+ MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0a6
+ MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0a6
+ MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0a6
+ MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0a6
+ MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0a6
+ MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0a6
+ MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0a6
+ MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0a6
+ MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0a6
+ MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0a6
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x130b0
+ MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb060 /* LE */
MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0a6
MX6QDL_PAD_EIM_RW__EIM_RW 0xb0a6 /* WE */
- MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb060 /* LE */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x130b0
- MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0a6
- MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0a6
- MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0a6
- MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0a6
- MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0a6
- MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0a6
- MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0a6
- MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0a6
- MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0a6
- MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0a6
- MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0a6
- MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0a6
- MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0a6
- MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0a6
- MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0a6
- MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0a6
>;
};
projects / linux-2.6-microblaze.git / commitdiff