net/sonic: Fix command register usage
authorFinn Thain <fthain@telegraphics.com.au>
Wed, 22 Jan 2020 22:07:26 +0000 (09:07 +1100)
committerDavid S. Miller <davem@davemloft.net>
Thu, 23 Jan 2020 20:24:37 +0000 (21:24 +0100)
There are several issues relating to command register usage during
chip initialization.

Firstly, the SONIC sometimes comes out of software reset with the
Start Timer bit set. This gets logged as,

    macsonic macsonic eth0: sonic_init: status=24, i=101

Avoid this by giving the Stop Timer command earlier than later.

Secondly, the loop that waits for the Read RRA command to complete has
the break condition inverted. That's why the for loop iterates until
its termination condition. Call the helper for this instead.

Finally, give the Receiver Enable command after clearing interrupts,
not before, to avoid the possibility of losing an interrupt.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/natsemi/sonic.c

index 42a6b87..914cec2 100644 (file)
@@ -664,7 +664,6 @@ static void sonic_multicast_list(struct net_device *dev)
  */
 static int sonic_init(struct net_device *dev)
 {
-       unsigned int cmd;
        struct sonic_local *lp = netdev_priv(dev);
        int i;
 
@@ -681,7 +680,7 @@ static int sonic_init(struct net_device *dev)
         * enable interrupts, then completely initialize the SONIC
         */
        SONIC_WRITE(SONIC_CMD, 0);
-       SONIC_WRITE(SONIC_CMD, SONIC_CR_RXDIS);
+       SONIC_WRITE(SONIC_CMD, SONIC_CR_RXDIS | SONIC_CR_STP);
        sonic_quiesce(dev, SONIC_CR_ALL);
 
        /*
@@ -711,14 +710,7 @@ static int sonic_init(struct net_device *dev)
        netif_dbg(lp, ifup, dev, "%s: issuing RRRA command\n", __func__);
 
        SONIC_WRITE(SONIC_CMD, SONIC_CR_RRRA);
-       i = 0;
-       while (i++ < 100) {
-               if (SONIC_READ(SONIC_CMD) & SONIC_CR_RRRA)
-                       break;
-       }
-
-       netif_dbg(lp, ifup, dev, "%s: status=%x, i=%d\n", __func__,
-                 SONIC_READ(SONIC_CMD), i);
+       sonic_quiesce(dev, SONIC_CR_RRRA);
 
        /*
         * Initialize the receive descriptors so that they
@@ -806,15 +798,11 @@ static int sonic_init(struct net_device *dev)
         * enable receiver, disable loopback
         * and enable all interrupts
         */
-       SONIC_WRITE(SONIC_CMD, SONIC_CR_RXEN | SONIC_CR_STP);
        SONIC_WRITE(SONIC_RCR, SONIC_RCR_DEFAULT);
        SONIC_WRITE(SONIC_TCR, SONIC_TCR_DEFAULT);
        SONIC_WRITE(SONIC_ISR, 0x7fff);
        SONIC_WRITE(SONIC_IMR, SONIC_IMR_DEFAULT);
-
-       cmd = SONIC_READ(SONIC_CMD);
-       if ((cmd & SONIC_CR_RXEN) == 0 || (cmd & SONIC_CR_STP) == 0)
-               printk(KERN_ERR "sonic_init: failed, status=%x\n", cmd);
+       SONIC_WRITE(SONIC_CMD, SONIC_CR_RXEN);
 
        netif_dbg(lp, ifup, dev, "%s: new status=%x\n", __func__,
                  SONIC_READ(SONIC_CMD));