1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * Synopsys DesignWare Multimedia Card Interface driver
4 * (Based on NXP driver for lpc 31xx)
6 * Copyright (C) 2009 NXP Semiconductors
7 * Copyright (C) 2009, 2010 Imagination Technologies Ltd.
10 #include <linux/blkdev.h>
11 #include <linux/clk.h>
12 #include <linux/debugfs.h>
13 #include <linux/device.h>
14 #include <linux/dma-mapping.h>
15 #include <linux/err.h>
16 #include <linux/init.h>
17 #include <linux/interrupt.h>
18 #include <linux/iopoll.h>
19 #include <linux/ioport.h>
20 #include <linux/module.h>
21 #include <linux/platform_device.h>
22 #include <linux/pm_runtime.h>
23 #include <linux/seq_file.h>
24 #include <linux/slab.h>
25 #include <linux/stat.h>
26 #include <linux/delay.h>
27 #include <linux/irq.h>
28 #include <linux/mmc/card.h>
29 #include <linux/mmc/host.h>
30 #include <linux/mmc/mmc.h>
31 #include <linux/mmc/sd.h>
32 #include <linux/mmc/sdio.h>
33 #include <linux/bitops.h>
34 #include <linux/regulator/consumer.h>
36 #include <linux/of_gpio.h>
37 #include <linux/mmc/slot-gpio.h>
41 /* Common flag combinations */
42 #define DW_MCI_DATA_ERROR_FLAGS (SDMMC_INT_DRTO | SDMMC_INT_DCRC | \
43 SDMMC_INT_HTO | SDMMC_INT_SBE | \
44 SDMMC_INT_EBE | SDMMC_INT_HLE)
45 #define DW_MCI_CMD_ERROR_FLAGS (SDMMC_INT_RTO | SDMMC_INT_RCRC | \
46 SDMMC_INT_RESP_ERR | SDMMC_INT_HLE)
47 #define DW_MCI_ERROR_FLAGS (DW_MCI_DATA_ERROR_FLAGS | \
48 DW_MCI_CMD_ERROR_FLAGS)
49 #define DW_MCI_SEND_STATUS 1
50 #define DW_MCI_RECV_STATUS 2
51 #define DW_MCI_DMA_THRESHOLD 16
53 #define DW_MCI_FREQ_MAX 200000000 /* unit: HZ */
54 #define DW_MCI_FREQ_MIN 100000 /* unit: HZ */
56 #define IDMAC_INT_CLR (SDMMC_IDMAC_INT_AI | SDMMC_IDMAC_INT_NI | \
57 SDMMC_IDMAC_INT_CES | SDMMC_IDMAC_INT_DU | \
58 SDMMC_IDMAC_INT_FBE | SDMMC_IDMAC_INT_RI | \
61 #define DESC_RING_BUF_SZ PAGE_SIZE
63 struct idmac_desc_64addr {
64 u32 des0; /* Control Descriptor */
65 #define IDMAC_OWN_CLR64(x) \
66 !((x) & cpu_to_le32(IDMAC_DES0_OWN))
68 u32 des1; /* Reserved */
70 u32 des2; /*Buffer sizes */
71 #define IDMAC_64ADDR_SET_BUFFER1_SIZE(d, s) \
72 ((d)->des2 = ((d)->des2 & cpu_to_le32(0x03ffe000)) | \
73 ((cpu_to_le32(s)) & cpu_to_le32(0x1fff)))
75 u32 des3; /* Reserved */
77 u32 des4; /* Lower 32-bits of Buffer Address Pointer 1*/
78 u32 des5; /* Upper 32-bits of Buffer Address Pointer 1*/
80 u32 des6; /* Lower 32-bits of Next Descriptor Address */
81 u32 des7; /* Upper 32-bits of Next Descriptor Address */
85 __le32 des0; /* Control Descriptor */
86 #define IDMAC_DES0_DIC BIT(1)
87 #define IDMAC_DES0_LD BIT(2)
88 #define IDMAC_DES0_FD BIT(3)
89 #define IDMAC_DES0_CH BIT(4)
90 #define IDMAC_DES0_ER BIT(5)
91 #define IDMAC_DES0_CES BIT(30)
92 #define IDMAC_DES0_OWN BIT(31)
94 __le32 des1; /* Buffer sizes */
95 #define IDMAC_SET_BUFFER1_SIZE(d, s) \
96 ((d)->des1 = ((d)->des1 & cpu_to_le32(0x03ffe000)) | (cpu_to_le32((s) & 0x1fff)))
98 __le32 des2; /* buffer 1 physical address */
100 __le32 des3; /* buffer 2 physical address */
103 /* Each descriptor can transfer up to 4KB of data in chained mode */
104 #define DW_MCI_DESC_DATA_LENGTH 0x1000
106 #if defined(CONFIG_DEBUG_FS)
107 static int dw_mci_req_show(struct seq_file *s, void *v)
109 struct dw_mci_slot *slot = s->private;
110 struct mmc_request *mrq;
111 struct mmc_command *cmd;
112 struct mmc_command *stop;
113 struct mmc_data *data;
115 /* Make sure we get a consistent snapshot */
116 spin_lock_bh(&slot->host->lock);
126 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
127 cmd->opcode, cmd->arg, cmd->flags,
128 cmd->resp[0], cmd->resp[1], cmd->resp[2],
129 cmd->resp[2], cmd->error);
131 seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
132 data->bytes_xfered, data->blocks,
133 data->blksz, data->flags, data->error);
136 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
137 stop->opcode, stop->arg, stop->flags,
138 stop->resp[0], stop->resp[1], stop->resp[2],
139 stop->resp[2], stop->error);
142 spin_unlock_bh(&slot->host->lock);
146 DEFINE_SHOW_ATTRIBUTE(dw_mci_req);
148 static int dw_mci_regs_show(struct seq_file *s, void *v)
150 struct dw_mci *host = s->private;
152 pm_runtime_get_sync(host->dev);
154 seq_printf(s, "STATUS:\t0x%08x\n", mci_readl(host, STATUS));
155 seq_printf(s, "RINTSTS:\t0x%08x\n", mci_readl(host, RINTSTS));
156 seq_printf(s, "CMD:\t0x%08x\n", mci_readl(host, CMD));
157 seq_printf(s, "CTRL:\t0x%08x\n", mci_readl(host, CTRL));
158 seq_printf(s, "INTMASK:\t0x%08x\n", mci_readl(host, INTMASK));
159 seq_printf(s, "CLKENA:\t0x%08x\n", mci_readl(host, CLKENA));
161 pm_runtime_put_autosuspend(host->dev);
165 DEFINE_SHOW_ATTRIBUTE(dw_mci_regs);
167 static void dw_mci_init_debugfs(struct dw_mci_slot *slot)
169 struct mmc_host *mmc = slot->mmc;
170 struct dw_mci *host = slot->host;
173 root = mmc->debugfs_root;
177 debugfs_create_file("regs", S_IRUSR, root, host, &dw_mci_regs_fops);
178 debugfs_create_file("req", S_IRUSR, root, slot, &dw_mci_req_fops);
179 debugfs_create_u32("state", S_IRUSR, root, &host->state);
180 debugfs_create_xul("pending_events", S_IRUSR, root,
181 &host->pending_events);
182 debugfs_create_xul("completed_events", S_IRUSR, root,
183 &host->completed_events);
185 #endif /* defined(CONFIG_DEBUG_FS) */
187 static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset)
191 ctrl = mci_readl(host, CTRL);
193 mci_writel(host, CTRL, ctrl);
195 /* wait till resets clear */
196 if (readl_poll_timeout_atomic(host->regs + SDMMC_CTRL, ctrl,
198 1, 500 * USEC_PER_MSEC)) {
200 "Timeout resetting block (ctrl reset %#x)\n",
208 static void dw_mci_wait_while_busy(struct dw_mci *host, u32 cmd_flags)
213 * Databook says that before issuing a new data transfer command
214 * we need to check to see if the card is busy. Data transfer commands
215 * all have SDMMC_CMD_PRV_DAT_WAIT set, so we'll key off that.
217 * ...also allow sending for SDMMC_CMD_VOLT_SWITCH where busy is
220 if ((cmd_flags & SDMMC_CMD_PRV_DAT_WAIT) &&
221 !(cmd_flags & SDMMC_CMD_VOLT_SWITCH)) {
222 if (readl_poll_timeout_atomic(host->regs + SDMMC_STATUS,
224 !(status & SDMMC_STATUS_BUSY),
225 10, 500 * USEC_PER_MSEC))
226 dev_err(host->dev, "Busy; trying anyway\n");
230 static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg)
232 struct dw_mci *host = slot->host;
233 unsigned int cmd_status = 0;
235 mci_writel(host, CMDARG, arg);
236 wmb(); /* drain writebuffer */
237 dw_mci_wait_while_busy(host, cmd);
238 mci_writel(host, CMD, SDMMC_CMD_START | cmd);
240 if (readl_poll_timeout_atomic(host->regs + SDMMC_CMD, cmd_status,
241 !(cmd_status & SDMMC_CMD_START),
242 1, 500 * USEC_PER_MSEC))
243 dev_err(&slot->mmc->class_dev,
244 "Timeout sending command (cmd %#x arg %#x status %#x)\n",
245 cmd, arg, cmd_status);
248 static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
250 struct dw_mci_slot *slot = mmc_priv(mmc);
251 struct dw_mci *host = slot->host;
254 cmd->error = -EINPROGRESS;
257 if (cmd->opcode == MMC_STOP_TRANSMISSION ||
258 cmd->opcode == MMC_GO_IDLE_STATE ||
259 cmd->opcode == MMC_GO_INACTIVE_STATE ||
260 (cmd->opcode == SD_IO_RW_DIRECT &&
261 ((cmd->arg >> 9) & 0x1FFFF) == SDIO_CCCR_ABORT))
262 cmdr |= SDMMC_CMD_STOP;
263 else if (cmd->opcode != MMC_SEND_STATUS && cmd->data)
264 cmdr |= SDMMC_CMD_PRV_DAT_WAIT;
266 if (cmd->opcode == SD_SWITCH_VOLTAGE) {
269 /* Special bit makes CMD11 not die */
270 cmdr |= SDMMC_CMD_VOLT_SWITCH;
272 /* Change state to continue to handle CMD11 weirdness */
273 WARN_ON(slot->host->state != STATE_SENDING_CMD);
274 slot->host->state = STATE_SENDING_CMD11;
277 * We need to disable low power mode (automatic clock stop)
278 * while doing voltage switch so we don't confuse the card,
279 * since stopping the clock is a specific part of the UHS
280 * voltage change dance.
282 * Note that low power mode (SDMMC_CLKEN_LOW_PWR) will be
283 * unconditionally turned back on in dw_mci_setup_bus() if it's
284 * ever called with a non-zero clock. That shouldn't happen
285 * until the voltage change is all done.
287 clk_en_a = mci_readl(host, CLKENA);
288 clk_en_a &= ~(SDMMC_CLKEN_LOW_PWR << slot->id);
289 mci_writel(host, CLKENA, clk_en_a);
290 mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
291 SDMMC_CMD_PRV_DAT_WAIT, 0);
294 if (cmd->flags & MMC_RSP_PRESENT) {
295 /* We expect a response, so set this bit */
296 cmdr |= SDMMC_CMD_RESP_EXP;
297 if (cmd->flags & MMC_RSP_136)
298 cmdr |= SDMMC_CMD_RESP_LONG;
301 if (cmd->flags & MMC_RSP_CRC)
302 cmdr |= SDMMC_CMD_RESP_CRC;
305 cmdr |= SDMMC_CMD_DAT_EXP;
306 if (cmd->data->flags & MMC_DATA_WRITE)
307 cmdr |= SDMMC_CMD_DAT_WR;
310 if (!test_bit(DW_MMC_CARD_NO_USE_HOLD, &slot->flags))
311 cmdr |= SDMMC_CMD_USE_HOLD_REG;
316 static u32 dw_mci_prep_stop_abort(struct dw_mci *host, struct mmc_command *cmd)
318 struct mmc_command *stop;
324 stop = &host->stop_abort;
326 memset(stop, 0, sizeof(struct mmc_command));
328 if (cmdr == MMC_READ_SINGLE_BLOCK ||
329 cmdr == MMC_READ_MULTIPLE_BLOCK ||
330 cmdr == MMC_WRITE_BLOCK ||
331 cmdr == MMC_WRITE_MULTIPLE_BLOCK ||
332 cmdr == MMC_SEND_TUNING_BLOCK ||
333 cmdr == MMC_SEND_TUNING_BLOCK_HS200) {
334 stop->opcode = MMC_STOP_TRANSMISSION;
336 stop->flags = MMC_RSP_R1B | MMC_CMD_AC;
337 } else if (cmdr == SD_IO_RW_EXTENDED) {
338 stop->opcode = SD_IO_RW_DIRECT;
339 stop->arg |= (1 << 31) | (0 << 28) | (SDIO_CCCR_ABORT << 9) |
340 ((cmd->arg >> 28) & 0x7);
341 stop->flags = MMC_RSP_SPI_R5 | MMC_RSP_R5 | MMC_CMD_AC;
346 cmdr = stop->opcode | SDMMC_CMD_STOP |
347 SDMMC_CMD_RESP_CRC | SDMMC_CMD_RESP_EXP;
349 if (!test_bit(DW_MMC_CARD_NO_USE_HOLD, &host->slot->flags))
350 cmdr |= SDMMC_CMD_USE_HOLD_REG;
355 static inline void dw_mci_set_cto(struct dw_mci *host)
357 unsigned int cto_clks;
358 unsigned int cto_div;
360 unsigned long irqflags;
362 cto_clks = mci_readl(host, TMOUT) & 0xff;
363 cto_div = (mci_readl(host, CLKDIV) & 0xff) * 2;
367 cto_ms = DIV_ROUND_UP_ULL((u64)MSEC_PER_SEC * cto_clks * cto_div,
370 /* add a bit spare time */
374 * The durations we're working with are fairly short so we have to be
375 * extra careful about synchronization here. Specifically in hardware a
376 * command timeout is _at most_ 5.1 ms, so that means we expect an
377 * interrupt (either command done or timeout) to come rather quickly
378 * after the mci_writel. ...but just in case we have a long interrupt
379 * latency let's add a bit of paranoia.
381 * In general we'll assume that at least an interrupt will be asserted
382 * in hardware by the time the cto_timer runs. ...and if it hasn't
383 * been asserted in hardware by that time then we'll assume it'll never
386 spin_lock_irqsave(&host->irq_lock, irqflags);
387 if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
388 mod_timer(&host->cto_timer,
389 jiffies + msecs_to_jiffies(cto_ms) + 1);
390 spin_unlock_irqrestore(&host->irq_lock, irqflags);
393 static void dw_mci_start_command(struct dw_mci *host,
394 struct mmc_command *cmd, u32 cmd_flags)
398 "start command: ARGR=0x%08x CMDR=0x%08x\n",
399 cmd->arg, cmd_flags);
401 mci_writel(host, CMDARG, cmd->arg);
402 wmb(); /* drain writebuffer */
403 dw_mci_wait_while_busy(host, cmd_flags);
405 mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
407 /* response expected command only */
408 if (cmd_flags & SDMMC_CMD_RESP_EXP)
409 dw_mci_set_cto(host);
412 static inline void send_stop_abort(struct dw_mci *host, struct mmc_data *data)
414 struct mmc_command *stop = &host->stop_abort;
416 dw_mci_start_command(host, stop, host->stop_cmdr);
419 /* DMA interface functions */
420 static void dw_mci_stop_dma(struct dw_mci *host)
422 if (host->using_dma) {
423 host->dma_ops->stop(host);
424 host->dma_ops->cleanup(host);
427 /* Data transfer was stopped by the interrupt handler */
428 set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
431 static void dw_mci_dma_cleanup(struct dw_mci *host)
433 struct mmc_data *data = host->data;
435 if (data && data->host_cookie == COOKIE_MAPPED) {
436 dma_unmap_sg(host->dev,
439 mmc_get_dma_dir(data));
440 data->host_cookie = COOKIE_UNMAPPED;
444 static void dw_mci_idmac_reset(struct dw_mci *host)
446 u32 bmod = mci_readl(host, BMOD);
447 /* Software reset of DMA */
448 bmod |= SDMMC_IDMAC_SWRESET;
449 mci_writel(host, BMOD, bmod);
452 static void dw_mci_idmac_stop_dma(struct dw_mci *host)
456 /* Disable and reset the IDMAC interface */
457 temp = mci_readl(host, CTRL);
458 temp &= ~SDMMC_CTRL_USE_IDMAC;
459 temp |= SDMMC_CTRL_DMA_RESET;
460 mci_writel(host, CTRL, temp);
462 /* Stop the IDMAC running */
463 temp = mci_readl(host, BMOD);
464 temp &= ~(SDMMC_IDMAC_ENABLE | SDMMC_IDMAC_FB);
465 temp |= SDMMC_IDMAC_SWRESET;
466 mci_writel(host, BMOD, temp);
469 static void dw_mci_dmac_complete_dma(void *arg)
471 struct dw_mci *host = arg;
472 struct mmc_data *data = host->data;
474 dev_vdbg(host->dev, "DMA complete\n");
476 if ((host->use_dma == TRANS_MODE_EDMAC) &&
477 data && (data->flags & MMC_DATA_READ))
478 /* Invalidate cache after read */
479 dma_sync_sg_for_cpu(mmc_dev(host->slot->mmc),
484 host->dma_ops->cleanup(host);
487 * If the card was removed, data will be NULL. No point in trying to
488 * send the stop command or waiting for NBUSY in this case.
491 set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
492 tasklet_schedule(&host->tasklet);
496 static int dw_mci_idmac_init(struct dw_mci *host)
500 if (host->dma_64bit_address == 1) {
501 struct idmac_desc_64addr *p;
502 /* Number of descriptors in the ring buffer */
504 DESC_RING_BUF_SZ / sizeof(struct idmac_desc_64addr);
506 /* Forward link the descriptor list */
507 for (i = 0, p = host->sg_cpu; i < host->ring_size - 1;
509 p->des6 = (host->sg_dma +
510 (sizeof(struct idmac_desc_64addr) *
511 (i + 1))) & 0xffffffff;
513 p->des7 = (u64)(host->sg_dma +
514 (sizeof(struct idmac_desc_64addr) *
516 /* Initialize reserved and buffer size fields to "0" */
523 /* Set the last descriptor as the end-of-ring descriptor */
524 p->des6 = host->sg_dma & 0xffffffff;
525 p->des7 = (u64)host->sg_dma >> 32;
526 p->des0 = IDMAC_DES0_ER;
529 struct idmac_desc *p;
530 /* Number of descriptors in the ring buffer */
532 DESC_RING_BUF_SZ / sizeof(struct idmac_desc);
534 /* Forward link the descriptor list */
535 for (i = 0, p = host->sg_cpu;
536 i < host->ring_size - 1;
538 p->des3 = cpu_to_le32(host->sg_dma +
539 (sizeof(struct idmac_desc) * (i + 1)));
544 /* Set the last descriptor as the end-of-ring descriptor */
545 p->des3 = cpu_to_le32(host->sg_dma);
546 p->des0 = cpu_to_le32(IDMAC_DES0_ER);
549 dw_mci_idmac_reset(host);
551 if (host->dma_64bit_address == 1) {
552 /* Mask out interrupts - get Tx & Rx complete only */
553 mci_writel(host, IDSTS64, IDMAC_INT_CLR);
554 mci_writel(host, IDINTEN64, SDMMC_IDMAC_INT_NI |
555 SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
557 /* Set the descriptor base address */
558 mci_writel(host, DBADDRL, host->sg_dma & 0xffffffff);
559 mci_writel(host, DBADDRU, (u64)host->sg_dma >> 32);
562 /* Mask out interrupts - get Tx & Rx complete only */
563 mci_writel(host, IDSTS, IDMAC_INT_CLR);
564 mci_writel(host, IDINTEN, SDMMC_IDMAC_INT_NI |
565 SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
567 /* Set the descriptor base address */
568 mci_writel(host, DBADDR, host->sg_dma);
574 static inline int dw_mci_prepare_desc64(struct dw_mci *host,
575 struct mmc_data *data,
578 unsigned int desc_len;
579 struct idmac_desc_64addr *desc_first, *desc_last, *desc;
583 desc_first = desc_last = desc = host->sg_cpu;
585 for (i = 0; i < sg_len; i++) {
586 unsigned int length = sg_dma_len(&data->sg[i]);
588 u64 mem_addr = sg_dma_address(&data->sg[i]);
590 for ( ; length ; desc++) {
591 desc_len = (length <= DW_MCI_DESC_DATA_LENGTH) ?
592 length : DW_MCI_DESC_DATA_LENGTH;
597 * Wait for the former clear OWN bit operation
598 * of IDMAC to make sure that this descriptor
599 * isn't still owned by IDMAC as IDMAC's write
600 * ops and CPU's read ops are asynchronous.
602 if (readl_poll_timeout_atomic(&desc->des0, val,
603 !(val & IDMAC_DES0_OWN),
604 10, 100 * USEC_PER_MSEC))
608 * Set the OWN bit and disable interrupts
609 * for this descriptor
611 desc->des0 = IDMAC_DES0_OWN | IDMAC_DES0_DIC |
615 IDMAC_64ADDR_SET_BUFFER1_SIZE(desc, desc_len);
617 /* Physical address to DMA to/from */
618 desc->des4 = mem_addr & 0xffffffff;
619 desc->des5 = mem_addr >> 32;
621 /* Update physical address for the next desc */
622 mem_addr += desc_len;
624 /* Save pointer to the last descriptor */
629 /* Set first descriptor */
630 desc_first->des0 |= IDMAC_DES0_FD;
632 /* Set last descriptor */
633 desc_last->des0 &= ~(IDMAC_DES0_CH | IDMAC_DES0_DIC);
634 desc_last->des0 |= IDMAC_DES0_LD;
638 /* restore the descriptor chain as it's polluted */
639 dev_dbg(host->dev, "descriptor is still owned by IDMAC.\n");
640 memset(host->sg_cpu, 0, DESC_RING_BUF_SZ);
641 dw_mci_idmac_init(host);
646 static inline int dw_mci_prepare_desc32(struct dw_mci *host,
647 struct mmc_data *data,
650 unsigned int desc_len;
651 struct idmac_desc *desc_first, *desc_last, *desc;
655 desc_first = desc_last = desc = host->sg_cpu;
657 for (i = 0; i < sg_len; i++) {
658 unsigned int length = sg_dma_len(&data->sg[i]);
660 u32 mem_addr = sg_dma_address(&data->sg[i]);
662 for ( ; length ; desc++) {
663 desc_len = (length <= DW_MCI_DESC_DATA_LENGTH) ?
664 length : DW_MCI_DESC_DATA_LENGTH;
669 * Wait for the former clear OWN bit operation
670 * of IDMAC to make sure that this descriptor
671 * isn't still owned by IDMAC as IDMAC's write
672 * ops and CPU's read ops are asynchronous.
674 if (readl_poll_timeout_atomic(&desc->des0, val,
675 IDMAC_OWN_CLR64(val),
677 100 * USEC_PER_MSEC))
681 * Set the OWN bit and disable interrupts
682 * for this descriptor
684 desc->des0 = cpu_to_le32(IDMAC_DES0_OWN |
689 IDMAC_SET_BUFFER1_SIZE(desc, desc_len);
691 /* Physical address to DMA to/from */
692 desc->des2 = cpu_to_le32(mem_addr);
694 /* Update physical address for the next desc */
695 mem_addr += desc_len;
697 /* Save pointer to the last descriptor */
702 /* Set first descriptor */
703 desc_first->des0 |= cpu_to_le32(IDMAC_DES0_FD);
705 /* Set last descriptor */
706 desc_last->des0 &= cpu_to_le32(~(IDMAC_DES0_CH |
708 desc_last->des0 |= cpu_to_le32(IDMAC_DES0_LD);
712 /* restore the descriptor chain as it's polluted */
713 dev_dbg(host->dev, "descriptor is still owned by IDMAC.\n");
714 memset(host->sg_cpu, 0, DESC_RING_BUF_SZ);
715 dw_mci_idmac_init(host);
719 static int dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len)
724 if (host->dma_64bit_address == 1)
725 ret = dw_mci_prepare_desc64(host, host->data, sg_len);
727 ret = dw_mci_prepare_desc32(host, host->data, sg_len);
732 /* drain writebuffer */
735 /* Make sure to reset DMA in case we did PIO before this */
736 dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET);
737 dw_mci_idmac_reset(host);
739 /* Select IDMAC interface */
740 temp = mci_readl(host, CTRL);
741 temp |= SDMMC_CTRL_USE_IDMAC;
742 mci_writel(host, CTRL, temp);
744 /* drain writebuffer */
747 /* Enable the IDMAC */
748 temp = mci_readl(host, BMOD);
749 temp |= SDMMC_IDMAC_ENABLE | SDMMC_IDMAC_FB;
750 mci_writel(host, BMOD, temp);
752 /* Start it running */
753 mci_writel(host, PLDMND, 1);
759 static const struct dw_mci_dma_ops dw_mci_idmac_ops = {
760 .init = dw_mci_idmac_init,
761 .start = dw_mci_idmac_start_dma,
762 .stop = dw_mci_idmac_stop_dma,
763 .complete = dw_mci_dmac_complete_dma,
764 .cleanup = dw_mci_dma_cleanup,
767 static void dw_mci_edmac_stop_dma(struct dw_mci *host)
769 dmaengine_terminate_async(host->dms->ch);
772 static int dw_mci_edmac_start_dma(struct dw_mci *host,
775 struct dma_slave_config cfg;
776 struct dma_async_tx_descriptor *desc = NULL;
777 struct scatterlist *sgl = host->data->sg;
778 static const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
779 u32 sg_elems = host->data->sg_len;
781 u32 fifo_offset = host->fifo_reg - host->regs;
784 /* Set external dma config: burst size, burst width */
785 cfg.dst_addr = host->phy_regs + fifo_offset;
786 cfg.src_addr = cfg.dst_addr;
787 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
788 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
790 /* Match burst msize with external dma config */
791 fifoth_val = mci_readl(host, FIFOTH);
792 cfg.dst_maxburst = mszs[(fifoth_val >> 28) & 0x7];
793 cfg.src_maxburst = cfg.dst_maxburst;
795 if (host->data->flags & MMC_DATA_WRITE)
796 cfg.direction = DMA_MEM_TO_DEV;
798 cfg.direction = DMA_DEV_TO_MEM;
800 ret = dmaengine_slave_config(host->dms->ch, &cfg);
802 dev_err(host->dev, "Failed to config edmac.\n");
806 desc = dmaengine_prep_slave_sg(host->dms->ch, sgl,
807 sg_len, cfg.direction,
808 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
810 dev_err(host->dev, "Can't prepare slave sg.\n");
814 /* Set dw_mci_dmac_complete_dma as callback */
815 desc->callback = dw_mci_dmac_complete_dma;
816 desc->callback_param = (void *)host;
817 dmaengine_submit(desc);
819 /* Flush cache before write */
820 if (host->data->flags & MMC_DATA_WRITE)
821 dma_sync_sg_for_device(mmc_dev(host->slot->mmc), sgl,
822 sg_elems, DMA_TO_DEVICE);
824 dma_async_issue_pending(host->dms->ch);
829 static int dw_mci_edmac_init(struct dw_mci *host)
831 /* Request external dma channel */
832 host->dms = kzalloc(sizeof(struct dw_mci_dma_slave), GFP_KERNEL);
836 host->dms->ch = dma_request_chan(host->dev, "rx-tx");
837 if (IS_ERR(host->dms->ch)) {
838 int ret = PTR_ERR(host->dms->ch);
840 dev_err(host->dev, "Failed to get external DMA channel.\n");
849 static void dw_mci_edmac_exit(struct dw_mci *host)
853 dma_release_channel(host->dms->ch);
854 host->dms->ch = NULL;
861 static const struct dw_mci_dma_ops dw_mci_edmac_ops = {
862 .init = dw_mci_edmac_init,
863 .exit = dw_mci_edmac_exit,
864 .start = dw_mci_edmac_start_dma,
865 .stop = dw_mci_edmac_stop_dma,
866 .complete = dw_mci_dmac_complete_dma,
867 .cleanup = dw_mci_dma_cleanup,
870 static int dw_mci_pre_dma_transfer(struct dw_mci *host,
871 struct mmc_data *data,
874 struct scatterlist *sg;
875 unsigned int i, sg_len;
877 if (data->host_cookie == COOKIE_PRE_MAPPED)
881 * We don't do DMA on "complex" transfers, i.e. with
882 * non-word-aligned buffers or lengths. Also, we don't bother
883 * with all the DMA setup overhead for short transfers.
885 if (data->blocks * data->blksz < DW_MCI_DMA_THRESHOLD)
891 for_each_sg(data->sg, sg, data->sg_len, i) {
892 if (sg->offset & 3 || sg->length & 3)
896 sg_len = dma_map_sg(host->dev,
899 mmc_get_dma_dir(data));
903 data->host_cookie = cookie;
908 static void dw_mci_pre_req(struct mmc_host *mmc,
909 struct mmc_request *mrq)
911 struct dw_mci_slot *slot = mmc_priv(mmc);
912 struct mmc_data *data = mrq->data;
914 if (!slot->host->use_dma || !data)
917 /* This data might be unmapped at this time */
918 data->host_cookie = COOKIE_UNMAPPED;
920 if (dw_mci_pre_dma_transfer(slot->host, mrq->data,
921 COOKIE_PRE_MAPPED) < 0)
922 data->host_cookie = COOKIE_UNMAPPED;
925 static void dw_mci_post_req(struct mmc_host *mmc,
926 struct mmc_request *mrq,
929 struct dw_mci_slot *slot = mmc_priv(mmc);
930 struct mmc_data *data = mrq->data;
932 if (!slot->host->use_dma || !data)
935 if (data->host_cookie != COOKIE_UNMAPPED)
936 dma_unmap_sg(slot->host->dev,
939 mmc_get_dma_dir(data));
940 data->host_cookie = COOKIE_UNMAPPED;
943 static int dw_mci_get_cd(struct mmc_host *mmc)
946 struct dw_mci_slot *slot = mmc_priv(mmc);
947 struct dw_mci *host = slot->host;
948 int gpio_cd = mmc_gpio_get_cd(mmc);
950 /* Use platform get_cd function, else try onboard card detect */
951 if (((mmc->caps & MMC_CAP_NEEDS_POLL)
952 || !mmc_card_is_removable(mmc))) {
955 if (!test_bit(DW_MMC_CARD_PRESENT, &slot->flags)) {
956 if (mmc->caps & MMC_CAP_NEEDS_POLL) {
957 dev_info(&mmc->class_dev,
958 "card is polling.\n");
960 dev_info(&mmc->class_dev,
961 "card is non-removable.\n");
963 set_bit(DW_MMC_CARD_PRESENT, &slot->flags);
967 } else if (gpio_cd >= 0)
970 present = (mci_readl(slot->host, CDETECT) & (1 << slot->id))
973 spin_lock_bh(&host->lock);
974 if (present && !test_and_set_bit(DW_MMC_CARD_PRESENT, &slot->flags))
975 dev_dbg(&mmc->class_dev, "card is present\n");
977 !test_and_clear_bit(DW_MMC_CARD_PRESENT, &slot->flags))
978 dev_dbg(&mmc->class_dev, "card is not present\n");
979 spin_unlock_bh(&host->lock);
984 static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data)
986 unsigned int blksz = data->blksz;
987 static const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
988 u32 fifo_width = 1 << host->data_shift;
989 u32 blksz_depth = blksz / fifo_width, fifoth_val;
990 u32 msize = 0, rx_wmark = 1, tx_wmark, tx_wmark_invers;
991 int idx = ARRAY_SIZE(mszs) - 1;
993 /* pio should ship this scenario */
997 tx_wmark = (host->fifo_depth) / 2;
998 tx_wmark_invers = host->fifo_depth - tx_wmark;
1002 * if blksz is not a multiple of the FIFO width
1004 if (blksz % fifo_width)
1008 if (!((blksz_depth % mszs[idx]) ||
1009 (tx_wmark_invers % mszs[idx]))) {
1011 rx_wmark = mszs[idx] - 1;
1014 } while (--idx > 0);
1016 * If idx is '0', it won't be tried
1017 * Thus, initial values are uesed
1020 fifoth_val = SDMMC_SET_FIFOTH(msize, rx_wmark, tx_wmark);
1021 mci_writel(host, FIFOTH, fifoth_val);
1024 static void dw_mci_ctrl_thld(struct dw_mci *host, struct mmc_data *data)
1026 unsigned int blksz = data->blksz;
1027 u32 blksz_depth, fifo_depth;
1032 * CDTHRCTL doesn't exist prior to 240A (in fact that register offset is
1033 * in the FIFO region, so we really shouldn't access it).
1035 if (host->verid < DW_MMC_240A ||
1036 (host->verid < DW_MMC_280A && data->flags & MMC_DATA_WRITE))
1040 * Card write Threshold is introduced since 2.80a
1041 * It's used when HS400 mode is enabled.
1043 if (data->flags & MMC_DATA_WRITE &&
1044 host->timing != MMC_TIMING_MMC_HS400)
1047 if (data->flags & MMC_DATA_WRITE)
1048 enable = SDMMC_CARD_WR_THR_EN;
1050 enable = SDMMC_CARD_RD_THR_EN;
1052 if (host->timing != MMC_TIMING_MMC_HS200 &&
1053 host->timing != MMC_TIMING_UHS_SDR104 &&
1054 host->timing != MMC_TIMING_MMC_HS400)
1057 blksz_depth = blksz / (1 << host->data_shift);
1058 fifo_depth = host->fifo_depth;
1060 if (blksz_depth > fifo_depth)
1064 * If (blksz_depth) >= (fifo_depth >> 1), should be 'thld_size <= blksz'
1065 * If (blksz_depth) < (fifo_depth >> 1), should be thld_size = blksz
1066 * Currently just choose blksz.
1069 mci_writel(host, CDTHRCTL, SDMMC_SET_THLD(thld_size, enable));
1073 mci_writel(host, CDTHRCTL, 0);
1076 static int dw_mci_submit_data_dma(struct dw_mci *host, struct mmc_data *data)
1078 unsigned long irqflags;
1082 host->using_dma = 0;
1084 /* If we don't have a channel, we can't do DMA */
1088 sg_len = dw_mci_pre_dma_transfer(host, data, COOKIE_MAPPED);
1090 host->dma_ops->stop(host);
1094 host->using_dma = 1;
1096 if (host->use_dma == TRANS_MODE_IDMAC)
1098 "sd sg_cpu: %#lx sg_dma: %#lx sg_len: %d\n",
1099 (unsigned long)host->sg_cpu,
1100 (unsigned long)host->sg_dma,
1104 * Decide the MSIZE and RX/TX Watermark.
1105 * If current block size is same with previous size,
1106 * no need to update fifoth.
1108 if (host->prev_blksz != data->blksz)
1109 dw_mci_adjust_fifoth(host, data);
1111 /* Enable the DMA interface */
1112 temp = mci_readl(host, CTRL);
1113 temp |= SDMMC_CTRL_DMA_ENABLE;
1114 mci_writel(host, CTRL, temp);
1116 /* Disable RX/TX IRQs, let DMA handle it */
1117 spin_lock_irqsave(&host->irq_lock, irqflags);
1118 temp = mci_readl(host, INTMASK);
1119 temp &= ~(SDMMC_INT_RXDR | SDMMC_INT_TXDR);
1120 mci_writel(host, INTMASK, temp);
1121 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1123 if (host->dma_ops->start(host, sg_len)) {
1124 host->dma_ops->stop(host);
1125 /* We can't do DMA, try PIO for this one */
1127 "%s: fall back to PIO mode for current transfer\n",
1135 static void dw_mci_submit_data(struct dw_mci *host, struct mmc_data *data)
1137 unsigned long irqflags;
1138 int flags = SG_MITER_ATOMIC;
1141 data->error = -EINPROGRESS;
1143 WARN_ON(host->data);
1147 if (data->flags & MMC_DATA_READ)
1148 host->dir_status = DW_MCI_RECV_STATUS;
1150 host->dir_status = DW_MCI_SEND_STATUS;
1152 dw_mci_ctrl_thld(host, data);
1154 if (dw_mci_submit_data_dma(host, data)) {
1155 if (host->data->flags & MMC_DATA_READ)
1156 flags |= SG_MITER_TO_SG;
1158 flags |= SG_MITER_FROM_SG;
1160 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
1161 host->sg = data->sg;
1162 host->part_buf_start = 0;
1163 host->part_buf_count = 0;
1165 mci_writel(host, RINTSTS, SDMMC_INT_TXDR | SDMMC_INT_RXDR);
1167 spin_lock_irqsave(&host->irq_lock, irqflags);
1168 temp = mci_readl(host, INTMASK);
1169 temp |= SDMMC_INT_TXDR | SDMMC_INT_RXDR;
1170 mci_writel(host, INTMASK, temp);
1171 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1173 temp = mci_readl(host, CTRL);
1174 temp &= ~SDMMC_CTRL_DMA_ENABLE;
1175 mci_writel(host, CTRL, temp);
1178 * Use the initial fifoth_val for PIO mode. If wm_algined
1179 * is set, we set watermark same as data size.
1180 * If next issued data may be transfered by DMA mode,
1181 * prev_blksz should be invalidated.
1183 if (host->wm_aligned)
1184 dw_mci_adjust_fifoth(host, data);
1186 mci_writel(host, FIFOTH, host->fifoth_val);
1187 host->prev_blksz = 0;
1190 * Keep the current block size.
1191 * It will be used to decide whether to update
1192 * fifoth register next time.
1194 host->prev_blksz = data->blksz;
1198 static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
1200 struct dw_mci *host = slot->host;
1201 unsigned int clock = slot->clock;
1204 u32 sdmmc_cmd_bits = SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT;
1206 /* We must continue to set bit 28 in CMD until the change is complete */
1207 if (host->state == STATE_WAITING_CMD11_DONE)
1208 sdmmc_cmd_bits |= SDMMC_CMD_VOLT_SWITCH;
1210 slot->mmc->actual_clock = 0;
1213 mci_writel(host, CLKENA, 0);
1214 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1215 } else if (clock != host->current_speed || force_clkinit) {
1216 div = host->bus_hz / clock;
1217 if (host->bus_hz % clock && host->bus_hz > clock)
1219 * move the + 1 after the divide to prevent
1220 * over-clocking the card.
1224 div = (host->bus_hz != clock) ? DIV_ROUND_UP(div, 2) : 0;
1226 if ((clock != slot->__clk_old &&
1227 !test_bit(DW_MMC_CARD_NEEDS_POLL, &slot->flags)) ||
1229 /* Silent the verbose log if calling from PM context */
1231 dev_info(&slot->mmc->class_dev,
1232 "Bus speed (slot %d) = %dHz (slot req %dHz, actual %dHZ div = %d)\n",
1233 slot->id, host->bus_hz, clock,
1234 div ? ((host->bus_hz / div) >> 1) :
1238 * If card is polling, display the message only
1239 * one time at boot time.
1241 if (slot->mmc->caps & MMC_CAP_NEEDS_POLL &&
1242 slot->mmc->f_min == clock)
1243 set_bit(DW_MMC_CARD_NEEDS_POLL, &slot->flags);
1247 mci_writel(host, CLKENA, 0);
1248 mci_writel(host, CLKSRC, 0);
1251 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1253 /* set clock to desired speed */
1254 mci_writel(host, CLKDIV, div);
1257 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1259 /* enable clock; only low power if no SDIO */
1260 clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
1261 if (!test_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags))
1262 clk_en_a |= SDMMC_CLKEN_LOW_PWR << slot->id;
1263 mci_writel(host, CLKENA, clk_en_a);
1266 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1268 /* keep the last clock value that was requested from core */
1269 slot->__clk_old = clock;
1270 slot->mmc->actual_clock = div ? ((host->bus_hz / div) >> 1) :
1274 host->current_speed = clock;
1276 /* Set the current slot bus width */
1277 mci_writel(host, CTYPE, (slot->ctype << slot->id));
1280 static void __dw_mci_start_request(struct dw_mci *host,
1281 struct dw_mci_slot *slot,
1282 struct mmc_command *cmd)
1284 struct mmc_request *mrq;
1285 struct mmc_data *data;
1292 host->pending_events = 0;
1293 host->completed_events = 0;
1294 host->cmd_status = 0;
1295 host->data_status = 0;
1296 host->dir_status = 0;
1300 mci_writel(host, TMOUT, 0xFFFFFFFF);
1301 mci_writel(host, BYTCNT, data->blksz*data->blocks);
1302 mci_writel(host, BLKSIZ, data->blksz);
1305 cmdflags = dw_mci_prepare_command(slot->mmc, cmd);
1307 /* this is the first command, send the initialization clock */
1308 if (test_and_clear_bit(DW_MMC_CARD_NEED_INIT, &slot->flags))
1309 cmdflags |= SDMMC_CMD_INIT;
1312 dw_mci_submit_data(host, data);
1313 wmb(); /* drain writebuffer */
1316 dw_mci_start_command(host, cmd, cmdflags);
1318 if (cmd->opcode == SD_SWITCH_VOLTAGE) {
1319 unsigned long irqflags;
1322 * Databook says to fail after 2ms w/ no response, but evidence
1323 * shows that sometimes the cmd11 interrupt takes over 130ms.
1324 * We'll set to 500ms, plus an extra jiffy just in case jiffies
1325 * is just about to roll over.
1327 * We do this whole thing under spinlock and only if the
1328 * command hasn't already completed (indicating the the irq
1329 * already ran so we don't want the timeout).
1331 spin_lock_irqsave(&host->irq_lock, irqflags);
1332 if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
1333 mod_timer(&host->cmd11_timer,
1334 jiffies + msecs_to_jiffies(500) + 1);
1335 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1338 host->stop_cmdr = dw_mci_prep_stop_abort(host, cmd);
1341 static void dw_mci_start_request(struct dw_mci *host,
1342 struct dw_mci_slot *slot)
1344 struct mmc_request *mrq = slot->mrq;
1345 struct mmc_command *cmd;
1347 cmd = mrq->sbc ? mrq->sbc : mrq->cmd;
1348 __dw_mci_start_request(host, slot, cmd);
1351 /* must be called with host->lock held */
1352 static void dw_mci_queue_request(struct dw_mci *host, struct dw_mci_slot *slot,
1353 struct mmc_request *mrq)
1355 dev_vdbg(&slot->mmc->class_dev, "queue request: state=%d\n",
1360 if (host->state == STATE_WAITING_CMD11_DONE) {
1361 dev_warn(&slot->mmc->class_dev,
1362 "Voltage change didn't complete\n");
1364 * this case isn't expected to happen, so we can
1365 * either crash here or just try to continue on
1366 * in the closest possible state
1368 host->state = STATE_IDLE;
1371 if (host->state == STATE_IDLE) {
1372 host->state = STATE_SENDING_CMD;
1373 dw_mci_start_request(host, slot);
1375 list_add_tail(&slot->queue_node, &host->queue);
1379 static void dw_mci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1381 struct dw_mci_slot *slot = mmc_priv(mmc);
1382 struct dw_mci *host = slot->host;
1387 * The check for card presence and queueing of the request must be
1388 * atomic, otherwise the card could be removed in between and the
1389 * request wouldn't fail until another card was inserted.
1392 if (!dw_mci_get_cd(mmc)) {
1393 mrq->cmd->error = -ENOMEDIUM;
1394 mmc_request_done(mmc, mrq);
1398 spin_lock_bh(&host->lock);
1400 dw_mci_queue_request(host, slot, mrq);
1402 spin_unlock_bh(&host->lock);
1405 static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1407 struct dw_mci_slot *slot = mmc_priv(mmc);
1408 const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
1412 switch (ios->bus_width) {
1413 case MMC_BUS_WIDTH_4:
1414 slot->ctype = SDMMC_CTYPE_4BIT;
1416 case MMC_BUS_WIDTH_8:
1417 slot->ctype = SDMMC_CTYPE_8BIT;
1420 /* set default 1 bit mode */
1421 slot->ctype = SDMMC_CTYPE_1BIT;
1424 regs = mci_readl(slot->host, UHS_REG);
1427 if (ios->timing == MMC_TIMING_MMC_DDR52 ||
1428 ios->timing == MMC_TIMING_UHS_DDR50 ||
1429 ios->timing == MMC_TIMING_MMC_HS400)
1430 regs |= ((0x1 << slot->id) << 16);
1432 regs &= ~((0x1 << slot->id) << 16);
1434 mci_writel(slot->host, UHS_REG, regs);
1435 slot->host->timing = ios->timing;
1438 * Use mirror of ios->clock to prevent race with mmc
1439 * core ios update when finding the minimum.
1441 slot->clock = ios->clock;
1443 if (drv_data && drv_data->set_ios)
1444 drv_data->set_ios(slot->host, ios);
1446 switch (ios->power_mode) {
1448 if (!IS_ERR(mmc->supply.vmmc)) {
1449 ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc,
1452 dev_err(slot->host->dev,
1453 "failed to enable vmmc regulator\n");
1454 /*return, if failed turn on vmmc*/
1458 set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
1459 regs = mci_readl(slot->host, PWREN);
1460 regs |= (1 << slot->id);
1461 mci_writel(slot->host, PWREN, regs);
1464 if (!slot->host->vqmmc_enabled) {
1465 if (!IS_ERR(mmc->supply.vqmmc)) {
1466 ret = regulator_enable(mmc->supply.vqmmc);
1468 dev_err(slot->host->dev,
1469 "failed to enable vqmmc\n");
1471 slot->host->vqmmc_enabled = true;
1474 /* Keep track so we don't reset again */
1475 slot->host->vqmmc_enabled = true;
1478 /* Reset our state machine after powering on */
1479 dw_mci_ctrl_reset(slot->host,
1480 SDMMC_CTRL_ALL_RESET_FLAGS);
1483 /* Adjust clock / bus width after power is up */
1484 dw_mci_setup_bus(slot, false);
1488 /* Turn clock off before power goes down */
1489 dw_mci_setup_bus(slot, false);
1491 if (!IS_ERR(mmc->supply.vmmc))
1492 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1494 if (!IS_ERR(mmc->supply.vqmmc) && slot->host->vqmmc_enabled)
1495 regulator_disable(mmc->supply.vqmmc);
1496 slot->host->vqmmc_enabled = false;
1498 regs = mci_readl(slot->host, PWREN);
1499 regs &= ~(1 << slot->id);
1500 mci_writel(slot->host, PWREN, regs);
1506 if (slot->host->state == STATE_WAITING_CMD11_DONE && ios->clock != 0)
1507 slot->host->state = STATE_IDLE;
1510 static int dw_mci_card_busy(struct mmc_host *mmc)
1512 struct dw_mci_slot *slot = mmc_priv(mmc);
1516 * Check the busy bit which is low when DAT[3:0]
1517 * (the data lines) are 0000
1519 status = mci_readl(slot->host, STATUS);
1521 return !!(status & SDMMC_STATUS_BUSY);
1524 static int dw_mci_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios)
1526 struct dw_mci_slot *slot = mmc_priv(mmc);
1527 struct dw_mci *host = slot->host;
1528 const struct dw_mci_drv_data *drv_data = host->drv_data;
1530 u32 v18 = SDMMC_UHS_18V << slot->id;
1533 if (drv_data && drv_data->switch_voltage)
1534 return drv_data->switch_voltage(mmc, ios);
1537 * Program the voltage. Note that some instances of dw_mmc may use
1538 * the UHS_REG for this. For other instances (like exynos) the UHS_REG
1539 * does no harm but you need to set the regulator directly. Try both.
1541 uhs = mci_readl(host, UHS_REG);
1542 if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330)
1547 if (!IS_ERR(mmc->supply.vqmmc)) {
1548 ret = mmc_regulator_set_vqmmc(mmc, ios);
1550 dev_dbg(&mmc->class_dev,
1551 "Regulator set error %d - %s V\n",
1552 ret, uhs & v18 ? "1.8" : "3.3");
1556 mci_writel(host, UHS_REG, uhs);
1561 static int dw_mci_get_ro(struct mmc_host *mmc)
1564 struct dw_mci_slot *slot = mmc_priv(mmc);
1565 int gpio_ro = mmc_gpio_get_ro(mmc);
1567 /* Use platform get_ro function, else try on board write protect */
1569 read_only = gpio_ro;
1572 mci_readl(slot->host, WRTPRT) & (1 << slot->id) ? 1 : 0;
1574 dev_dbg(&mmc->class_dev, "card is %s\n",
1575 read_only ? "read-only" : "read-write");
1580 static void dw_mci_hw_reset(struct mmc_host *mmc)
1582 struct dw_mci_slot *slot = mmc_priv(mmc);
1583 struct dw_mci *host = slot->host;
1586 if (host->use_dma == TRANS_MODE_IDMAC)
1587 dw_mci_idmac_reset(host);
1589 if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET |
1590 SDMMC_CTRL_FIFO_RESET))
1594 * According to eMMC spec, card reset procedure:
1595 * tRstW >= 1us: RST_n pulse width
1596 * tRSCA >= 200us: RST_n to Command time
1597 * tRSTH >= 1us: RST_n high period
1599 reset = mci_readl(host, RST_N);
1600 reset &= ~(SDMMC_RST_HWACTIVE << slot->id);
1601 mci_writel(host, RST_N, reset);
1603 reset |= SDMMC_RST_HWACTIVE << slot->id;
1604 mci_writel(host, RST_N, reset);
1605 usleep_range(200, 300);
1608 static void dw_mci_init_card(struct mmc_host *mmc, struct mmc_card *card)
1610 struct dw_mci_slot *slot = mmc_priv(mmc);
1611 struct dw_mci *host = slot->host;
1614 * Low power mode will stop the card clock when idle. According to the
1615 * description of the CLKENA register we should disable low power mode
1616 * for SDIO cards if we need SDIO interrupts to work.
1618 if (mmc->caps & MMC_CAP_SDIO_IRQ) {
1619 const u32 clken_low_pwr = SDMMC_CLKEN_LOW_PWR << slot->id;
1623 clk_en_a_old = mci_readl(host, CLKENA);
1625 if (card->type == MMC_TYPE_SDIO ||
1626 card->type == MMC_TYPE_SD_COMBO) {
1627 set_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags);
1628 clk_en_a = clk_en_a_old & ~clken_low_pwr;
1630 clear_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags);
1631 clk_en_a = clk_en_a_old | clken_low_pwr;
1634 if (clk_en_a != clk_en_a_old) {
1635 mci_writel(host, CLKENA, clk_en_a);
1636 mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
1637 SDMMC_CMD_PRV_DAT_WAIT, 0);
1642 static void __dw_mci_enable_sdio_irq(struct dw_mci_slot *slot, int enb)
1644 struct dw_mci *host = slot->host;
1645 unsigned long irqflags;
1648 spin_lock_irqsave(&host->irq_lock, irqflags);
1650 /* Enable/disable Slot Specific SDIO interrupt */
1651 int_mask = mci_readl(host, INTMASK);
1653 int_mask |= SDMMC_INT_SDIO(slot->sdio_id);
1655 int_mask &= ~SDMMC_INT_SDIO(slot->sdio_id);
1656 mci_writel(host, INTMASK, int_mask);
1658 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1661 static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
1663 struct dw_mci_slot *slot = mmc_priv(mmc);
1664 struct dw_mci *host = slot->host;
1666 __dw_mci_enable_sdio_irq(slot, enb);
1668 /* Avoid runtime suspending the device when SDIO IRQ is enabled */
1670 pm_runtime_get_noresume(host->dev);
1672 pm_runtime_put_noidle(host->dev);
1675 static void dw_mci_ack_sdio_irq(struct mmc_host *mmc)
1677 struct dw_mci_slot *slot = mmc_priv(mmc);
1679 __dw_mci_enable_sdio_irq(slot, 1);
1682 static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode)
1684 struct dw_mci_slot *slot = mmc_priv(mmc);
1685 struct dw_mci *host = slot->host;
1686 const struct dw_mci_drv_data *drv_data = host->drv_data;
1689 if (drv_data && drv_data->execute_tuning)
1690 err = drv_data->execute_tuning(slot, opcode);
1694 static int dw_mci_prepare_hs400_tuning(struct mmc_host *mmc,
1695 struct mmc_ios *ios)
1697 struct dw_mci_slot *slot = mmc_priv(mmc);
1698 struct dw_mci *host = slot->host;
1699 const struct dw_mci_drv_data *drv_data = host->drv_data;
1701 if (drv_data && drv_data->prepare_hs400_tuning)
1702 return drv_data->prepare_hs400_tuning(host, ios);
1707 static bool dw_mci_reset(struct dw_mci *host)
1709 u32 flags = SDMMC_CTRL_RESET | SDMMC_CTRL_FIFO_RESET;
1714 * Resetting generates a block interrupt, hence setting
1715 * the scatter-gather pointer to NULL.
1718 sg_miter_stop(&host->sg_miter);
1723 flags |= SDMMC_CTRL_DMA_RESET;
1725 if (dw_mci_ctrl_reset(host, flags)) {
1727 * In all cases we clear the RAWINTS
1728 * register to clear any interrupts.
1730 mci_writel(host, RINTSTS, 0xFFFFFFFF);
1732 if (!host->use_dma) {
1737 /* Wait for dma_req to be cleared */
1738 if (readl_poll_timeout_atomic(host->regs + SDMMC_STATUS,
1740 !(status & SDMMC_STATUS_DMA_REQ),
1741 1, 500 * USEC_PER_MSEC)) {
1743 "%s: Timeout waiting for dma_req to be cleared\n",
1748 /* when using DMA next we reset the fifo again */
1749 if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_FIFO_RESET))
1752 /* if the controller reset bit did clear, then set clock regs */
1753 if (!(mci_readl(host, CTRL) & SDMMC_CTRL_RESET)) {
1755 "%s: fifo/dma reset bits didn't clear but ciu was reset, doing clock update\n",
1761 if (host->use_dma == TRANS_MODE_IDMAC)
1762 /* It is also required that we reinit idmac */
1763 dw_mci_idmac_init(host);
1768 /* After a CTRL reset we need to have CIU set clock registers */
1769 mci_send_cmd(host->slot, SDMMC_CMD_UPD_CLK, 0);
1774 static const struct mmc_host_ops dw_mci_ops = {
1775 .request = dw_mci_request,
1776 .pre_req = dw_mci_pre_req,
1777 .post_req = dw_mci_post_req,
1778 .set_ios = dw_mci_set_ios,
1779 .get_ro = dw_mci_get_ro,
1780 .get_cd = dw_mci_get_cd,
1781 .hw_reset = dw_mci_hw_reset,
1782 .enable_sdio_irq = dw_mci_enable_sdio_irq,
1783 .ack_sdio_irq = dw_mci_ack_sdio_irq,
1784 .execute_tuning = dw_mci_execute_tuning,
1785 .card_busy = dw_mci_card_busy,
1786 .start_signal_voltage_switch = dw_mci_switch_voltage,
1787 .init_card = dw_mci_init_card,
1788 .prepare_hs400_tuning = dw_mci_prepare_hs400_tuning,
1791 static void dw_mci_request_end(struct dw_mci *host, struct mmc_request *mrq)
1792 __releases(&host->lock)
1793 __acquires(&host->lock)
1795 struct dw_mci_slot *slot;
1796 struct mmc_host *prev_mmc = host->slot->mmc;
1798 WARN_ON(host->cmd || host->data);
1800 host->slot->mrq = NULL;
1802 if (!list_empty(&host->queue)) {
1803 slot = list_entry(host->queue.next,
1804 struct dw_mci_slot, queue_node);
1805 list_del(&slot->queue_node);
1806 dev_vdbg(host->dev, "list not empty: %s is next\n",
1807 mmc_hostname(slot->mmc));
1808 host->state = STATE_SENDING_CMD;
1809 dw_mci_start_request(host, slot);
1811 dev_vdbg(host->dev, "list empty\n");
1813 if (host->state == STATE_SENDING_CMD11)
1814 host->state = STATE_WAITING_CMD11_DONE;
1816 host->state = STATE_IDLE;
1819 spin_unlock(&host->lock);
1820 mmc_request_done(prev_mmc, mrq);
1821 spin_lock(&host->lock);
1824 static int dw_mci_command_complete(struct dw_mci *host, struct mmc_command *cmd)
1826 u32 status = host->cmd_status;
1828 host->cmd_status = 0;
1830 /* Read the response from the card (up to 16 bytes) */
1831 if (cmd->flags & MMC_RSP_PRESENT) {
1832 if (cmd->flags & MMC_RSP_136) {
1833 cmd->resp[3] = mci_readl(host, RESP0);
1834 cmd->resp[2] = mci_readl(host, RESP1);
1835 cmd->resp[1] = mci_readl(host, RESP2);
1836 cmd->resp[0] = mci_readl(host, RESP3);
1838 cmd->resp[0] = mci_readl(host, RESP0);
1845 if (status & SDMMC_INT_RTO)
1846 cmd->error = -ETIMEDOUT;
1847 else if ((cmd->flags & MMC_RSP_CRC) && (status & SDMMC_INT_RCRC))
1848 cmd->error = -EILSEQ;
1849 else if (status & SDMMC_INT_RESP_ERR)
1857 static int dw_mci_data_complete(struct dw_mci *host, struct mmc_data *data)
1859 u32 status = host->data_status;
1861 if (status & DW_MCI_DATA_ERROR_FLAGS) {
1862 if (status & SDMMC_INT_DRTO) {
1863 data->error = -ETIMEDOUT;
1864 } else if (status & SDMMC_INT_DCRC) {
1865 data->error = -EILSEQ;
1866 } else if (status & SDMMC_INT_EBE) {
1867 if (host->dir_status ==
1868 DW_MCI_SEND_STATUS) {
1870 * No data CRC status was returned.
1871 * The number of bytes transferred
1872 * will be exaggerated in PIO mode.
1874 data->bytes_xfered = 0;
1875 data->error = -ETIMEDOUT;
1876 } else if (host->dir_status ==
1877 DW_MCI_RECV_STATUS) {
1878 data->error = -EILSEQ;
1881 /* SDMMC_INT_SBE is included */
1882 data->error = -EILSEQ;
1885 dev_dbg(host->dev, "data error, status 0x%08x\n", status);
1888 * After an error, there may be data lingering
1893 data->bytes_xfered = data->blocks * data->blksz;
1900 static void dw_mci_set_drto(struct dw_mci *host)
1902 unsigned int drto_clks;
1903 unsigned int drto_div;
1904 unsigned int drto_ms;
1905 unsigned long irqflags;
1907 drto_clks = mci_readl(host, TMOUT) >> 8;
1908 drto_div = (mci_readl(host, CLKDIV) & 0xff) * 2;
1912 drto_ms = DIV_ROUND_UP_ULL((u64)MSEC_PER_SEC * drto_clks * drto_div,
1915 /* add a bit spare time */
1918 spin_lock_irqsave(&host->irq_lock, irqflags);
1919 if (!test_bit(EVENT_DATA_COMPLETE, &host->pending_events))
1920 mod_timer(&host->dto_timer,
1921 jiffies + msecs_to_jiffies(drto_ms));
1922 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1925 static bool dw_mci_clear_pending_cmd_complete(struct dw_mci *host)
1927 if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
1931 * Really be certain that the timer has stopped. This is a bit of
1932 * paranoia and could only really happen if we had really bad
1933 * interrupt latency and the interrupt routine and timeout were
1934 * running concurrently so that the del_timer() in the interrupt
1935 * handler couldn't run.
1937 WARN_ON(del_timer_sync(&host->cto_timer));
1938 clear_bit(EVENT_CMD_COMPLETE, &host->pending_events);
1943 static bool dw_mci_clear_pending_data_complete(struct dw_mci *host)
1945 if (!test_bit(EVENT_DATA_COMPLETE, &host->pending_events))
1948 /* Extra paranoia just like dw_mci_clear_pending_cmd_complete() */
1949 WARN_ON(del_timer_sync(&host->dto_timer));
1950 clear_bit(EVENT_DATA_COMPLETE, &host->pending_events);
1955 static void dw_mci_tasklet_func(struct tasklet_struct *t)
1957 struct dw_mci *host = from_tasklet(host, t, tasklet);
1958 struct mmc_data *data;
1959 struct mmc_command *cmd;
1960 struct mmc_request *mrq;
1961 enum dw_mci_state state;
1962 enum dw_mci_state prev_state;
1965 spin_lock(&host->lock);
1967 state = host->state;
1976 case STATE_WAITING_CMD11_DONE:
1979 case STATE_SENDING_CMD11:
1980 case STATE_SENDING_CMD:
1981 if (!dw_mci_clear_pending_cmd_complete(host))
1986 set_bit(EVENT_CMD_COMPLETE, &host->completed_events);
1987 err = dw_mci_command_complete(host, cmd);
1988 if (cmd == mrq->sbc && !err) {
1989 __dw_mci_start_request(host, host->slot,
1994 if (cmd->data && err) {
1996 * During UHS tuning sequence, sending the stop
1997 * command after the response CRC error would
1998 * throw the system into a confused state
1999 * causing all future tuning phases to report
2002 * In such case controller will move into a data
2003 * transfer state after a response error or
2004 * response CRC error. Let's let that finish
2005 * before trying to send a stop, so we'll go to
2006 * STATE_SENDING_DATA.
2008 * Although letting the data transfer take place
2009 * will waste a bit of time (we already know
2010 * the command was bad), it can't cause any
2011 * errors since it's possible it would have
2012 * taken place anyway if this tasklet got
2013 * delayed. Allowing the transfer to take place
2014 * avoids races and keeps things simple.
2016 if (err != -ETIMEDOUT) {
2017 state = STATE_SENDING_DATA;
2021 dw_mci_stop_dma(host);
2022 send_stop_abort(host, data);
2023 state = STATE_SENDING_STOP;
2027 if (!cmd->data || err) {
2028 dw_mci_request_end(host, mrq);
2032 prev_state = state = STATE_SENDING_DATA;
2035 case STATE_SENDING_DATA:
2037 * We could get a data error and never a transfer
2038 * complete so we'd better check for it here.
2040 * Note that we don't really care if we also got a
2041 * transfer complete; stopping the DMA and sending an
2044 if (test_and_clear_bit(EVENT_DATA_ERROR,
2045 &host->pending_events)) {
2046 dw_mci_stop_dma(host);
2047 if (!(host->data_status & (SDMMC_INT_DRTO |
2049 send_stop_abort(host, data);
2050 state = STATE_DATA_ERROR;
2054 if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
2055 &host->pending_events)) {
2057 * If all data-related interrupts don't come
2058 * within the given time in reading data state.
2060 if (host->dir_status == DW_MCI_RECV_STATUS)
2061 dw_mci_set_drto(host);
2065 set_bit(EVENT_XFER_COMPLETE, &host->completed_events);
2068 * Handle an EVENT_DATA_ERROR that might have shown up
2069 * before the transfer completed. This might not have
2070 * been caught by the check above because the interrupt
2071 * could have gone off between the previous check and
2072 * the check for transfer complete.
2074 * Technically this ought not be needed assuming we
2075 * get a DATA_COMPLETE eventually (we'll notice the
2076 * error and end the request), but it shouldn't hurt.
2078 * This has the advantage of sending the stop command.
2080 if (test_and_clear_bit(EVENT_DATA_ERROR,
2081 &host->pending_events)) {
2082 dw_mci_stop_dma(host);
2083 if (!(host->data_status & (SDMMC_INT_DRTO |
2085 send_stop_abort(host, data);
2086 state = STATE_DATA_ERROR;
2089 prev_state = state = STATE_DATA_BUSY;
2093 case STATE_DATA_BUSY:
2094 if (!dw_mci_clear_pending_data_complete(host)) {
2096 * If data error interrupt comes but data over
2097 * interrupt doesn't come within the given time.
2098 * in reading data state.
2100 if (host->dir_status == DW_MCI_RECV_STATUS)
2101 dw_mci_set_drto(host);
2106 set_bit(EVENT_DATA_COMPLETE, &host->completed_events);
2107 err = dw_mci_data_complete(host, data);
2110 if (!data->stop || mrq->sbc) {
2111 if (mrq->sbc && data->stop)
2112 data->stop->error = 0;
2113 dw_mci_request_end(host, mrq);
2117 /* stop command for open-ended transfer*/
2119 send_stop_abort(host, data);
2122 * If we don't have a command complete now we'll
2123 * never get one since we just reset everything;
2124 * better end the request.
2126 * If we do have a command complete we'll fall
2127 * through to the SENDING_STOP command and
2128 * everything will be peachy keen.
2130 if (!test_bit(EVENT_CMD_COMPLETE,
2131 &host->pending_events)) {
2133 dw_mci_request_end(host, mrq);
2139 * If err has non-zero,
2140 * stop-abort command has been already issued.
2142 prev_state = state = STATE_SENDING_STOP;
2146 case STATE_SENDING_STOP:
2147 if (!dw_mci_clear_pending_cmd_complete(host))
2150 /* CMD error in data command */
2151 if (mrq->cmd->error && mrq->data)
2157 if (!mrq->sbc && mrq->stop)
2158 dw_mci_command_complete(host, mrq->stop);
2160 host->cmd_status = 0;
2162 dw_mci_request_end(host, mrq);
2165 case STATE_DATA_ERROR:
2166 if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
2167 &host->pending_events))
2170 state = STATE_DATA_BUSY;
2173 } while (state != prev_state);
2175 host->state = state;
2177 spin_unlock(&host->lock);
2181 /* push final bytes to part_buf, only use during push */
2182 static void dw_mci_set_part_bytes(struct dw_mci *host, void *buf, int cnt)
2184 memcpy((void *)&host->part_buf, buf, cnt);
2185 host->part_buf_count = cnt;
2188 /* append bytes to part_buf, only use during push */
2189 static int dw_mci_push_part_bytes(struct dw_mci *host, void *buf, int cnt)
2191 cnt = min(cnt, (1 << host->data_shift) - host->part_buf_count);
2192 memcpy((void *)&host->part_buf + host->part_buf_count, buf, cnt);
2193 host->part_buf_count += cnt;
2197 /* pull first bytes from part_buf, only use during pull */
2198 static int dw_mci_pull_part_bytes(struct dw_mci *host, void *buf, int cnt)
2200 cnt = min_t(int, cnt, host->part_buf_count);
2202 memcpy(buf, (void *)&host->part_buf + host->part_buf_start,
2204 host->part_buf_count -= cnt;
2205 host->part_buf_start += cnt;
2210 /* pull final bytes from the part_buf, assuming it's just been filled */
2211 static void dw_mci_pull_final_bytes(struct dw_mci *host, void *buf, int cnt)
2213 memcpy(buf, &host->part_buf, cnt);
2214 host->part_buf_start = cnt;
2215 host->part_buf_count = (1 << host->data_shift) - cnt;
2218 static void dw_mci_push_data16(struct dw_mci *host, void *buf, int cnt)
2220 struct mmc_data *data = host->data;
2223 /* try and push anything in the part_buf */
2224 if (unlikely(host->part_buf_count)) {
2225 int len = dw_mci_push_part_bytes(host, buf, cnt);
2229 if (host->part_buf_count == 2) {
2230 mci_fifo_writew(host->fifo_reg, host->part_buf16);
2231 host->part_buf_count = 0;
2234 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2235 if (unlikely((unsigned long)buf & 0x1)) {
2237 u16 aligned_buf[64];
2238 int len = min(cnt & -2, (int)sizeof(aligned_buf));
2239 int items = len >> 1;
2241 /* memcpy from input buffer into aligned buffer */
2242 memcpy(aligned_buf, buf, len);
2245 /* push data from aligned buffer into fifo */
2246 for (i = 0; i < items; ++i)
2247 mci_fifo_writew(host->fifo_reg, aligned_buf[i]);
2254 for (; cnt >= 2; cnt -= 2)
2255 mci_fifo_writew(host->fifo_reg, *pdata++);
2258 /* put anything remaining in the part_buf */
2260 dw_mci_set_part_bytes(host, buf, cnt);
2261 /* Push data if we have reached the expected data length */
2262 if ((data->bytes_xfered + init_cnt) ==
2263 (data->blksz * data->blocks))
2264 mci_fifo_writew(host->fifo_reg, host->part_buf16);
2268 static void dw_mci_pull_data16(struct dw_mci *host, void *buf, int cnt)
2270 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2271 if (unlikely((unsigned long)buf & 0x1)) {
2273 /* pull data from fifo into aligned buffer */
2274 u16 aligned_buf[64];
2275 int len = min(cnt & -2, (int)sizeof(aligned_buf));
2276 int items = len >> 1;
2279 for (i = 0; i < items; ++i)
2280 aligned_buf[i] = mci_fifo_readw(host->fifo_reg);
2281 /* memcpy from aligned buffer into output buffer */
2282 memcpy(buf, aligned_buf, len);
2291 for (; cnt >= 2; cnt -= 2)
2292 *pdata++ = mci_fifo_readw(host->fifo_reg);
2296 host->part_buf16 = mci_fifo_readw(host->fifo_reg);
2297 dw_mci_pull_final_bytes(host, buf, cnt);
2301 static void dw_mci_push_data32(struct dw_mci *host, void *buf, int cnt)
2303 struct mmc_data *data = host->data;
2306 /* try and push anything in the part_buf */
2307 if (unlikely(host->part_buf_count)) {
2308 int len = dw_mci_push_part_bytes(host, buf, cnt);
2312 if (host->part_buf_count == 4) {
2313 mci_fifo_writel(host->fifo_reg, host->part_buf32);
2314 host->part_buf_count = 0;
2317 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2318 if (unlikely((unsigned long)buf & 0x3)) {
2320 u32 aligned_buf[32];
2321 int len = min(cnt & -4, (int)sizeof(aligned_buf));
2322 int items = len >> 2;
2324 /* memcpy from input buffer into aligned buffer */
2325 memcpy(aligned_buf, buf, len);
2328 /* push data from aligned buffer into fifo */
2329 for (i = 0; i < items; ++i)
2330 mci_fifo_writel(host->fifo_reg, aligned_buf[i]);
2337 for (; cnt >= 4; cnt -= 4)
2338 mci_fifo_writel(host->fifo_reg, *pdata++);
2341 /* put anything remaining in the part_buf */
2343 dw_mci_set_part_bytes(host, buf, cnt);
2344 /* Push data if we have reached the expected data length */
2345 if ((data->bytes_xfered + init_cnt) ==
2346 (data->blksz * data->blocks))
2347 mci_fifo_writel(host->fifo_reg, host->part_buf32);
2351 static void dw_mci_pull_data32(struct dw_mci *host, void *buf, int cnt)
2353 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2354 if (unlikely((unsigned long)buf & 0x3)) {
2356 /* pull data from fifo into aligned buffer */
2357 u32 aligned_buf[32];
2358 int len = min(cnt & -4, (int)sizeof(aligned_buf));
2359 int items = len >> 2;
2362 for (i = 0; i < items; ++i)
2363 aligned_buf[i] = mci_fifo_readl(host->fifo_reg);
2364 /* memcpy from aligned buffer into output buffer */
2365 memcpy(buf, aligned_buf, len);
2374 for (; cnt >= 4; cnt -= 4)
2375 *pdata++ = mci_fifo_readl(host->fifo_reg);
2379 host->part_buf32 = mci_fifo_readl(host->fifo_reg);
2380 dw_mci_pull_final_bytes(host, buf, cnt);
2384 static void dw_mci_push_data64(struct dw_mci *host, void *buf, int cnt)
2386 struct mmc_data *data = host->data;
2389 /* try and push anything in the part_buf */
2390 if (unlikely(host->part_buf_count)) {
2391 int len = dw_mci_push_part_bytes(host, buf, cnt);
2396 if (host->part_buf_count == 8) {
2397 mci_fifo_writeq(host->fifo_reg, host->part_buf);
2398 host->part_buf_count = 0;
2401 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2402 if (unlikely((unsigned long)buf & 0x7)) {
2404 u64 aligned_buf[16];
2405 int len = min(cnt & -8, (int)sizeof(aligned_buf));
2406 int items = len >> 3;
2408 /* memcpy from input buffer into aligned buffer */
2409 memcpy(aligned_buf, buf, len);
2412 /* push data from aligned buffer into fifo */
2413 for (i = 0; i < items; ++i)
2414 mci_fifo_writeq(host->fifo_reg, aligned_buf[i]);
2421 for (; cnt >= 8; cnt -= 8)
2422 mci_fifo_writeq(host->fifo_reg, *pdata++);
2425 /* put anything remaining in the part_buf */
2427 dw_mci_set_part_bytes(host, buf, cnt);
2428 /* Push data if we have reached the expected data length */
2429 if ((data->bytes_xfered + init_cnt) ==
2430 (data->blksz * data->blocks))
2431 mci_fifo_writeq(host->fifo_reg, host->part_buf);
2435 static void dw_mci_pull_data64(struct dw_mci *host, void *buf, int cnt)
2437 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2438 if (unlikely((unsigned long)buf & 0x7)) {
2440 /* pull data from fifo into aligned buffer */
2441 u64 aligned_buf[16];
2442 int len = min(cnt & -8, (int)sizeof(aligned_buf));
2443 int items = len >> 3;
2446 for (i = 0; i < items; ++i)
2447 aligned_buf[i] = mci_fifo_readq(host->fifo_reg);
2449 /* memcpy from aligned buffer into output buffer */
2450 memcpy(buf, aligned_buf, len);
2459 for (; cnt >= 8; cnt -= 8)
2460 *pdata++ = mci_fifo_readq(host->fifo_reg);
2464 host->part_buf = mci_fifo_readq(host->fifo_reg);
2465 dw_mci_pull_final_bytes(host, buf, cnt);
2469 static void dw_mci_pull_data(struct dw_mci *host, void *buf, int cnt)
2473 /* get remaining partial bytes */
2474 len = dw_mci_pull_part_bytes(host, buf, cnt);
2475 if (unlikely(len == cnt))
2480 /* get the rest of the data */
2481 host->pull_data(host, buf, cnt);
2484 static void dw_mci_read_data_pio(struct dw_mci *host, bool dto)
2486 struct sg_mapping_iter *sg_miter = &host->sg_miter;
2488 unsigned int offset;
2489 struct mmc_data *data = host->data;
2490 int shift = host->data_shift;
2493 unsigned int remain, fcnt;
2496 if (!sg_miter_next(sg_miter))
2499 host->sg = sg_miter->piter.sg;
2500 buf = sg_miter->addr;
2501 remain = sg_miter->length;
2505 fcnt = (SDMMC_GET_FCNT(mci_readl(host, STATUS))
2506 << shift) + host->part_buf_count;
2507 len = min(remain, fcnt);
2510 dw_mci_pull_data(host, (void *)(buf + offset), len);
2511 data->bytes_xfered += len;
2516 sg_miter->consumed = offset;
2517 status = mci_readl(host, MINTSTS);
2518 mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
2519 /* if the RXDR is ready read again */
2520 } while ((status & SDMMC_INT_RXDR) ||
2521 (dto && SDMMC_GET_FCNT(mci_readl(host, STATUS))));
2524 if (!sg_miter_next(sg_miter))
2526 sg_miter->consumed = 0;
2528 sg_miter_stop(sg_miter);
2532 sg_miter_stop(sg_miter);
2534 smp_wmb(); /* drain writebuffer */
2535 set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
2538 static void dw_mci_write_data_pio(struct dw_mci *host)
2540 struct sg_mapping_iter *sg_miter = &host->sg_miter;
2542 unsigned int offset;
2543 struct mmc_data *data = host->data;
2544 int shift = host->data_shift;
2547 unsigned int fifo_depth = host->fifo_depth;
2548 unsigned int remain, fcnt;
2551 if (!sg_miter_next(sg_miter))
2554 host->sg = sg_miter->piter.sg;
2555 buf = sg_miter->addr;
2556 remain = sg_miter->length;
2560 fcnt = ((fifo_depth -
2561 SDMMC_GET_FCNT(mci_readl(host, STATUS)))
2562 << shift) - host->part_buf_count;
2563 len = min(remain, fcnt);
2566 host->push_data(host, (void *)(buf + offset), len);
2567 data->bytes_xfered += len;
2572 sg_miter->consumed = offset;
2573 status = mci_readl(host, MINTSTS);
2574 mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
2575 } while (status & SDMMC_INT_TXDR); /* if TXDR write again */
2578 if (!sg_miter_next(sg_miter))
2580 sg_miter->consumed = 0;
2582 sg_miter_stop(sg_miter);
2586 sg_miter_stop(sg_miter);
2588 smp_wmb(); /* drain writebuffer */
2589 set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
2592 static void dw_mci_cmd_interrupt(struct dw_mci *host, u32 status)
2594 del_timer(&host->cto_timer);
2596 if (!host->cmd_status)
2597 host->cmd_status = status;
2599 smp_wmb(); /* drain writebuffer */
2601 set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
2602 tasklet_schedule(&host->tasklet);
2605 static void dw_mci_handle_cd(struct dw_mci *host)
2607 struct dw_mci_slot *slot = host->slot;
2609 mmc_detect_change(slot->mmc,
2610 msecs_to_jiffies(host->pdata->detect_delay_ms));
2613 static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
2615 struct dw_mci *host = dev_id;
2617 struct dw_mci_slot *slot = host->slot;
2619 pending = mci_readl(host, MINTSTS); /* read-only mask reg */
2622 /* Check volt switch first, since it can look like an error */
2623 if ((host->state == STATE_SENDING_CMD11) &&
2624 (pending & SDMMC_INT_VOLT_SWITCH)) {
2625 mci_writel(host, RINTSTS, SDMMC_INT_VOLT_SWITCH);
2626 pending &= ~SDMMC_INT_VOLT_SWITCH;
2629 * Hold the lock; we know cmd11_timer can't be kicked
2630 * off after the lock is released, so safe to delete.
2632 spin_lock(&host->irq_lock);
2633 dw_mci_cmd_interrupt(host, pending);
2634 spin_unlock(&host->irq_lock);
2636 del_timer(&host->cmd11_timer);
2639 if (pending & DW_MCI_CMD_ERROR_FLAGS) {
2640 spin_lock(&host->irq_lock);
2642 del_timer(&host->cto_timer);
2643 mci_writel(host, RINTSTS, DW_MCI_CMD_ERROR_FLAGS);
2644 host->cmd_status = pending;
2645 smp_wmb(); /* drain writebuffer */
2646 set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
2648 spin_unlock(&host->irq_lock);
2651 if (pending & DW_MCI_DATA_ERROR_FLAGS) {
2652 /* if there is an error report DATA_ERROR */
2653 mci_writel(host, RINTSTS, DW_MCI_DATA_ERROR_FLAGS);
2654 host->data_status = pending;
2655 smp_wmb(); /* drain writebuffer */
2656 set_bit(EVENT_DATA_ERROR, &host->pending_events);
2657 tasklet_schedule(&host->tasklet);
2660 if (pending & SDMMC_INT_DATA_OVER) {
2661 spin_lock(&host->irq_lock);
2663 del_timer(&host->dto_timer);
2665 mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
2666 if (!host->data_status)
2667 host->data_status = pending;
2668 smp_wmb(); /* drain writebuffer */
2669 if (host->dir_status == DW_MCI_RECV_STATUS) {
2670 if (host->sg != NULL)
2671 dw_mci_read_data_pio(host, true);
2673 set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
2674 tasklet_schedule(&host->tasklet);
2676 spin_unlock(&host->irq_lock);
2679 if (pending & SDMMC_INT_RXDR) {
2680 mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
2681 if (host->dir_status == DW_MCI_RECV_STATUS && host->sg)
2682 dw_mci_read_data_pio(host, false);
2685 if (pending & SDMMC_INT_TXDR) {
2686 mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
2687 if (host->dir_status == DW_MCI_SEND_STATUS && host->sg)
2688 dw_mci_write_data_pio(host);
2691 if (pending & SDMMC_INT_CMD_DONE) {
2692 spin_lock(&host->irq_lock);
2694 mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE);
2695 dw_mci_cmd_interrupt(host, pending);
2697 spin_unlock(&host->irq_lock);
2700 if (pending & SDMMC_INT_CD) {
2701 mci_writel(host, RINTSTS, SDMMC_INT_CD);
2702 dw_mci_handle_cd(host);
2705 if (pending & SDMMC_INT_SDIO(slot->sdio_id)) {
2706 mci_writel(host, RINTSTS,
2707 SDMMC_INT_SDIO(slot->sdio_id));
2708 __dw_mci_enable_sdio_irq(slot, 0);
2709 sdio_signal_irq(slot->mmc);
2714 if (host->use_dma != TRANS_MODE_IDMAC)
2717 /* Handle IDMA interrupts */
2718 if (host->dma_64bit_address == 1) {
2719 pending = mci_readl(host, IDSTS64);
2720 if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
2721 mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_TI |
2722 SDMMC_IDMAC_INT_RI);
2723 mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_NI);
2724 if (!test_bit(EVENT_DATA_ERROR, &host->pending_events))
2725 host->dma_ops->complete((void *)host);
2728 pending = mci_readl(host, IDSTS);
2729 if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
2730 mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI |
2731 SDMMC_IDMAC_INT_RI);
2732 mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
2733 if (!test_bit(EVENT_DATA_ERROR, &host->pending_events))
2734 host->dma_ops->complete((void *)host);
2741 static int dw_mci_init_slot_caps(struct dw_mci_slot *slot)
2743 struct dw_mci *host = slot->host;
2744 const struct dw_mci_drv_data *drv_data = host->drv_data;
2745 struct mmc_host *mmc = slot->mmc;
2748 if (host->pdata->caps)
2749 mmc->caps = host->pdata->caps;
2751 if (host->pdata->pm_caps)
2752 mmc->pm_caps = host->pdata->pm_caps;
2754 if (host->dev->of_node) {
2755 ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
2759 ctrl_id = to_platform_device(host->dev)->id;
2762 if (drv_data && drv_data->caps) {
2763 if (ctrl_id >= drv_data->num_caps) {
2764 dev_err(host->dev, "invalid controller id %d\n",
2768 mmc->caps |= drv_data->caps[ctrl_id];
2771 if (host->pdata->caps2)
2772 mmc->caps2 = host->pdata->caps2;
2774 mmc->f_min = DW_MCI_FREQ_MIN;
2776 mmc->f_max = DW_MCI_FREQ_MAX;
2778 /* Process SDIO IRQs through the sdio_irq_work. */
2779 if (mmc->caps & MMC_CAP_SDIO_IRQ)
2780 mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
2785 static int dw_mci_init_slot(struct dw_mci *host)
2787 struct mmc_host *mmc;
2788 struct dw_mci_slot *slot;
2791 mmc = mmc_alloc_host(sizeof(struct dw_mci_slot), host->dev);
2795 slot = mmc_priv(mmc);
2797 slot->sdio_id = host->sdio_id0 + slot->id;
2802 mmc->ops = &dw_mci_ops;
2804 /*if there are external regulators, get them*/
2805 ret = mmc_regulator_get_supply(mmc);
2807 goto err_host_allocated;
2809 if (!mmc->ocr_avail)
2810 mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
2812 ret = mmc_of_parse(mmc);
2814 goto err_host_allocated;
2816 ret = dw_mci_init_slot_caps(slot);
2818 goto err_host_allocated;
2820 /* Useful defaults if platform data is unset. */
2821 if (host->use_dma == TRANS_MODE_IDMAC) {
2822 mmc->max_segs = host->ring_size;
2823 mmc->max_blk_size = 65535;
2824 mmc->max_seg_size = 0x1000;
2825 mmc->max_req_size = mmc->max_seg_size * host->ring_size;
2826 mmc->max_blk_count = mmc->max_req_size / 512;
2827 } else if (host->use_dma == TRANS_MODE_EDMAC) {
2829 mmc->max_blk_size = 65535;
2830 mmc->max_blk_count = 65535;
2832 mmc->max_blk_size * mmc->max_blk_count;
2833 mmc->max_seg_size = mmc->max_req_size;
2835 /* TRANS_MODE_PIO */
2837 mmc->max_blk_size = 65535; /* BLKSIZ is 16 bits */
2838 mmc->max_blk_count = 512;
2839 mmc->max_req_size = mmc->max_blk_size *
2841 mmc->max_seg_size = mmc->max_req_size;
2846 ret = mmc_add_host(mmc);
2848 goto err_host_allocated;
2850 #if defined(CONFIG_DEBUG_FS)
2851 dw_mci_init_debugfs(slot);
2861 static void dw_mci_cleanup_slot(struct dw_mci_slot *slot)
2863 /* Debugfs stuff is cleaned up by mmc core */
2864 mmc_remove_host(slot->mmc);
2865 slot->host->slot = NULL;
2866 mmc_free_host(slot->mmc);
2869 static void dw_mci_init_dma(struct dw_mci *host)
2872 struct device *dev = host->dev;
2875 * Check tansfer mode from HCON[17:16]
2876 * Clear the ambiguous description of dw_mmc databook:
2877 * 2b'00: No DMA Interface -> Actually means using Internal DMA block
2878 * 2b'01: DesignWare DMA Interface -> Synopsys DW-DMA block
2879 * 2b'10: Generic DMA Interface -> non-Synopsys generic DMA block
2880 * 2b'11: Non DW DMA Interface -> pio only
2881 * Compared to DesignWare DMA Interface, Generic DMA Interface has a
2882 * simpler request/acknowledge handshake mechanism and both of them
2883 * are regarded as external dma master for dw_mmc.
2885 host->use_dma = SDMMC_GET_TRANS_MODE(mci_readl(host, HCON));
2886 if (host->use_dma == DMA_INTERFACE_IDMA) {
2887 host->use_dma = TRANS_MODE_IDMAC;
2888 } else if (host->use_dma == DMA_INTERFACE_DWDMA ||
2889 host->use_dma == DMA_INTERFACE_GDMA) {
2890 host->use_dma = TRANS_MODE_EDMAC;
2895 /* Determine which DMA interface to use */
2896 if (host->use_dma == TRANS_MODE_IDMAC) {
2898 * Check ADDR_CONFIG bit in HCON to find
2899 * IDMAC address bus width
2901 addr_config = SDMMC_GET_ADDR_CONFIG(mci_readl(host, HCON));
2903 if (addr_config == 1) {
2904 /* host supports IDMAC in 64-bit address mode */
2905 host->dma_64bit_address = 1;
2907 "IDMAC supports 64-bit address mode.\n");
2908 if (!dma_set_mask(host->dev, DMA_BIT_MASK(64)))
2909 dma_set_coherent_mask(host->dev,
2912 /* host supports IDMAC in 32-bit address mode */
2913 host->dma_64bit_address = 0;
2915 "IDMAC supports 32-bit address mode.\n");
2918 /* Alloc memory for sg translation */
2919 host->sg_cpu = dmam_alloc_coherent(host->dev,
2921 &host->sg_dma, GFP_KERNEL);
2922 if (!host->sg_cpu) {
2924 "%s: could not alloc DMA memory\n",
2929 host->dma_ops = &dw_mci_idmac_ops;
2930 dev_info(host->dev, "Using internal DMA controller.\n");
2932 /* TRANS_MODE_EDMAC: check dma bindings again */
2933 if ((device_property_read_string_array(dev, "dma-names",
2935 !device_property_present(dev, "dmas")) {
2938 host->dma_ops = &dw_mci_edmac_ops;
2939 dev_info(host->dev, "Using external DMA controller.\n");
2942 if (host->dma_ops->init && host->dma_ops->start &&
2943 host->dma_ops->stop && host->dma_ops->cleanup) {
2944 if (host->dma_ops->init(host)) {
2945 dev_err(host->dev, "%s: Unable to initialize DMA Controller.\n",
2950 dev_err(host->dev, "DMA initialization not found.\n");
2957 dev_info(host->dev, "Using PIO mode.\n");
2958 host->use_dma = TRANS_MODE_PIO;
2961 static void dw_mci_cmd11_timer(struct timer_list *t)
2963 struct dw_mci *host = from_timer(host, t, cmd11_timer);
2965 if (host->state != STATE_SENDING_CMD11) {
2966 dev_warn(host->dev, "Unexpected CMD11 timeout\n");
2970 host->cmd_status = SDMMC_INT_RTO;
2971 set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
2972 tasklet_schedule(&host->tasklet);
2975 static void dw_mci_cto_timer(struct timer_list *t)
2977 struct dw_mci *host = from_timer(host, t, cto_timer);
2978 unsigned long irqflags;
2981 spin_lock_irqsave(&host->irq_lock, irqflags);
2984 * If somehow we have very bad interrupt latency it's remotely possible
2985 * that the timer could fire while the interrupt is still pending or
2986 * while the interrupt is midway through running. Let's be paranoid
2987 * and detect those two cases. Note that this is paranoia is somewhat
2988 * justified because in this function we don't actually cancel the
2989 * pending command in the controller--we just assume it will never come.
2991 pending = mci_readl(host, MINTSTS); /* read-only mask reg */
2992 if (pending & (DW_MCI_CMD_ERROR_FLAGS | SDMMC_INT_CMD_DONE)) {
2993 /* The interrupt should fire; no need to act but we can warn */
2994 dev_warn(host->dev, "Unexpected interrupt latency\n");
2997 if (test_bit(EVENT_CMD_COMPLETE, &host->pending_events)) {
2998 /* Presumably interrupt handler couldn't delete the timer */
2999 dev_warn(host->dev, "CTO timeout when already completed\n");
3004 * Continued paranoia to make sure we're in the state we expect.
3005 * This paranoia isn't really justified but it seems good to be safe.
3007 switch (host->state) {
3008 case STATE_SENDING_CMD11:
3009 case STATE_SENDING_CMD:
3010 case STATE_SENDING_STOP:
3012 * If CMD_DONE interrupt does NOT come in sending command
3013 * state, we should notify the driver to terminate current
3014 * transfer and report a command timeout to the core.
3016 host->cmd_status = SDMMC_INT_RTO;
3017 set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
3018 tasklet_schedule(&host->tasklet);
3021 dev_warn(host->dev, "Unexpected command timeout, state %d\n",
3027 spin_unlock_irqrestore(&host->irq_lock, irqflags);
3030 static void dw_mci_dto_timer(struct timer_list *t)
3032 struct dw_mci *host = from_timer(host, t, dto_timer);
3033 unsigned long irqflags;
3036 spin_lock_irqsave(&host->irq_lock, irqflags);
3039 * The DTO timer is much longer than the CTO timer, so it's even less
3040 * likely that we'll these cases, but it pays to be paranoid.
3042 pending = mci_readl(host, MINTSTS); /* read-only mask reg */
3043 if (pending & SDMMC_INT_DATA_OVER) {
3044 /* The interrupt should fire; no need to act but we can warn */
3045 dev_warn(host->dev, "Unexpected data interrupt latency\n");
3048 if (test_bit(EVENT_DATA_COMPLETE, &host->pending_events)) {
3049 /* Presumably interrupt handler couldn't delete the timer */
3050 dev_warn(host->dev, "DTO timeout when already completed\n");
3055 * Continued paranoia to make sure we're in the state we expect.
3056 * This paranoia isn't really justified but it seems good to be safe.
3058 switch (host->state) {
3059 case STATE_SENDING_DATA:
3060 case STATE_DATA_BUSY:
3062 * If DTO interrupt does NOT come in sending data state,
3063 * we should notify the driver to terminate current transfer
3064 * and report a data timeout to the core.
3066 host->data_status = SDMMC_INT_DRTO;
3067 set_bit(EVENT_DATA_ERROR, &host->pending_events);
3068 set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
3069 tasklet_schedule(&host->tasklet);
3072 dev_warn(host->dev, "Unexpected data timeout, state %d\n",
3078 spin_unlock_irqrestore(&host->irq_lock, irqflags);
3082 static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
3084 struct dw_mci_board *pdata;
3085 struct device *dev = host->dev;
3086 const struct dw_mci_drv_data *drv_data = host->drv_data;
3088 u32 clock_frequency;
3090 pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
3092 return ERR_PTR(-ENOMEM);
3094 /* find reset controller when exist */
3095 pdata->rstc = devm_reset_control_get_optional_exclusive(dev, "reset");
3096 if (IS_ERR(pdata->rstc))
3097 return ERR_CAST(pdata->rstc);
3099 if (device_property_read_u32(dev, "fifo-depth", &pdata->fifo_depth))
3101 "fifo-depth property not found, using value of FIFOTH register as default\n");
3103 device_property_read_u32(dev, "card-detect-delay",
3104 &pdata->detect_delay_ms);
3106 device_property_read_u32(dev, "data-addr", &host->data_addr_override);
3108 if (device_property_present(dev, "fifo-watermark-aligned"))
3109 host->wm_aligned = true;
3111 if (!device_property_read_u32(dev, "clock-frequency", &clock_frequency))
3112 pdata->bus_hz = clock_frequency;
3114 if (drv_data && drv_data->parse_dt) {
3115 ret = drv_data->parse_dt(host);
3117 return ERR_PTR(ret);
3123 #else /* CONFIG_OF */
3124 static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
3126 return ERR_PTR(-EINVAL);
3128 #endif /* CONFIG_OF */
3130 static void dw_mci_enable_cd(struct dw_mci *host)
3132 unsigned long irqflags;
3136 * No need for CD if all slots have a non-error GPIO
3137 * as well as broken card detection is found.
3139 if (host->slot->mmc->caps & MMC_CAP_NEEDS_POLL)
3142 if (mmc_gpio_get_cd(host->slot->mmc) < 0) {
3143 spin_lock_irqsave(&host->irq_lock, irqflags);
3144 temp = mci_readl(host, INTMASK);
3145 temp |= SDMMC_INT_CD;
3146 mci_writel(host, INTMASK, temp);
3147 spin_unlock_irqrestore(&host->irq_lock, irqflags);
3151 int dw_mci_probe(struct dw_mci *host)
3153 const struct dw_mci_drv_data *drv_data = host->drv_data;
3154 int width, i, ret = 0;
3158 host->pdata = dw_mci_parse_dt(host);
3159 if (IS_ERR(host->pdata))
3160 return dev_err_probe(host->dev, PTR_ERR(host->pdata),
3161 "platform data not available\n");
3164 host->biu_clk = devm_clk_get(host->dev, "biu");
3165 if (IS_ERR(host->biu_clk)) {
3166 dev_dbg(host->dev, "biu clock not available\n");
3168 ret = clk_prepare_enable(host->biu_clk);
3170 dev_err(host->dev, "failed to enable biu clock\n");
3175 host->ciu_clk = devm_clk_get(host->dev, "ciu");
3176 if (IS_ERR(host->ciu_clk)) {
3177 dev_dbg(host->dev, "ciu clock not available\n");
3178 host->bus_hz = host->pdata->bus_hz;
3180 ret = clk_prepare_enable(host->ciu_clk);
3182 dev_err(host->dev, "failed to enable ciu clock\n");
3186 if (host->pdata->bus_hz) {
3187 ret = clk_set_rate(host->ciu_clk, host->pdata->bus_hz);
3190 "Unable to set bus rate to %uHz\n",
3191 host->pdata->bus_hz);
3193 host->bus_hz = clk_get_rate(host->ciu_clk);
3196 if (!host->bus_hz) {
3198 "Platform data must supply bus speed\n");
3203 if (host->pdata->rstc) {
3204 reset_control_assert(host->pdata->rstc);
3205 usleep_range(10, 50);
3206 reset_control_deassert(host->pdata->rstc);
3209 if (drv_data && drv_data->init) {
3210 ret = drv_data->init(host);
3213 "implementation specific init failed\n");
3218 timer_setup(&host->cmd11_timer, dw_mci_cmd11_timer, 0);
3219 timer_setup(&host->cto_timer, dw_mci_cto_timer, 0);
3220 timer_setup(&host->dto_timer, dw_mci_dto_timer, 0);
3222 spin_lock_init(&host->lock);
3223 spin_lock_init(&host->irq_lock);
3224 INIT_LIST_HEAD(&host->queue);
3227 * Get the host data width - this assumes that HCON has been set with
3228 * the correct values.
3230 i = SDMMC_GET_HDATA_WIDTH(mci_readl(host, HCON));
3232 host->push_data = dw_mci_push_data16;
3233 host->pull_data = dw_mci_pull_data16;
3235 host->data_shift = 1;
3236 } else if (i == 2) {
3237 host->push_data = dw_mci_push_data64;
3238 host->pull_data = dw_mci_pull_data64;
3240 host->data_shift = 3;
3242 /* Check for a reserved value, and warn if it is */
3244 "HCON reports a reserved host data width!\n"
3245 "Defaulting to 32-bit access.\n");
3246 host->push_data = dw_mci_push_data32;
3247 host->pull_data = dw_mci_pull_data32;
3249 host->data_shift = 2;
3252 /* Reset all blocks */
3253 if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS)) {
3258 host->dma_ops = host->pdata->dma_ops;
3259 dw_mci_init_dma(host);
3261 /* Clear the interrupts for the host controller */
3262 mci_writel(host, RINTSTS, 0xFFFFFFFF);
3263 mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
3265 /* Put in max timeout */
3266 mci_writel(host, TMOUT, 0xFFFFFFFF);
3269 * FIFO threshold settings RxMark = fifo_size / 2 - 1,
3270 * Tx Mark = fifo_size / 2 DMA Size = 8
3272 if (!host->pdata->fifo_depth) {
3274 * Power-on value of RX_WMark is FIFO_DEPTH-1, but this may
3275 * have been overwritten by the bootloader, just like we're
3276 * about to do, so if you know the value for your hardware, you
3277 * should put it in the platform data.
3279 fifo_size = mci_readl(host, FIFOTH);
3280 fifo_size = 1 + ((fifo_size >> 16) & 0xfff);
3282 fifo_size = host->pdata->fifo_depth;
3284 host->fifo_depth = fifo_size;
3286 SDMMC_SET_FIFOTH(0x2, fifo_size / 2 - 1, fifo_size / 2);
3287 mci_writel(host, FIFOTH, host->fifoth_val);
3289 /* disable clock to CIU */
3290 mci_writel(host, CLKENA, 0);
3291 mci_writel(host, CLKSRC, 0);
3294 * In 2.40a spec, Data offset is changed.
3295 * Need to check the version-id and set data-offset for DATA register.
3297 host->verid = SDMMC_GET_VERID(mci_readl(host, VERID));
3298 dev_info(host->dev, "Version ID is %04x\n", host->verid);
3300 if (host->data_addr_override)
3301 host->fifo_reg = host->regs + host->data_addr_override;
3302 else if (host->verid < DW_MMC_240A)
3303 host->fifo_reg = host->regs + DATA_OFFSET;
3305 host->fifo_reg = host->regs + DATA_240A_OFFSET;
3307 tasklet_setup(&host->tasklet, dw_mci_tasklet_func);
3308 ret = devm_request_irq(host->dev, host->irq, dw_mci_interrupt,
3309 host->irq_flags, "dw-mci", host);
3314 * Enable interrupts for command done, data over, data empty,
3315 * receive ready and error such as transmit, receive timeout, crc error
3317 mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
3318 SDMMC_INT_TXDR | SDMMC_INT_RXDR |
3319 DW_MCI_ERROR_FLAGS);
3320 /* Enable mci interrupt */
3321 mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
3324 "DW MMC controller at irq %d,%d bit host data width,%u deep fifo\n",
3325 host->irq, width, fifo_size);
3327 /* We need at least one slot to succeed */
3328 ret = dw_mci_init_slot(host);
3330 dev_dbg(host->dev, "slot %d init failed\n", i);
3334 /* Now that slots are all setup, we can enable card detect */
3335 dw_mci_enable_cd(host);
3340 if (host->use_dma && host->dma_ops->exit)
3341 host->dma_ops->exit(host);
3343 reset_control_assert(host->pdata->rstc);
3346 clk_disable_unprepare(host->ciu_clk);
3349 clk_disable_unprepare(host->biu_clk);
3353 EXPORT_SYMBOL(dw_mci_probe);
3355 void dw_mci_remove(struct dw_mci *host)
3357 dev_dbg(host->dev, "remove slot\n");
3359 dw_mci_cleanup_slot(host->slot);
3361 mci_writel(host, RINTSTS, 0xFFFFFFFF);
3362 mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
3364 /* disable clock to CIU */
3365 mci_writel(host, CLKENA, 0);
3366 mci_writel(host, CLKSRC, 0);
3368 if (host->use_dma && host->dma_ops->exit)
3369 host->dma_ops->exit(host);
3371 reset_control_assert(host->pdata->rstc);
3373 clk_disable_unprepare(host->ciu_clk);
3374 clk_disable_unprepare(host->biu_clk);
3376 EXPORT_SYMBOL(dw_mci_remove);
3381 int dw_mci_runtime_suspend(struct device *dev)
3383 struct dw_mci *host = dev_get_drvdata(dev);
3385 if (host->use_dma && host->dma_ops->exit)
3386 host->dma_ops->exit(host);
3388 clk_disable_unprepare(host->ciu_clk);
3391 (mmc_can_gpio_cd(host->slot->mmc) ||
3392 !mmc_card_is_removable(host->slot->mmc)))
3393 clk_disable_unprepare(host->biu_clk);
3397 EXPORT_SYMBOL(dw_mci_runtime_suspend);
3399 int dw_mci_runtime_resume(struct device *dev)
3402 struct dw_mci *host = dev_get_drvdata(dev);
3405 (mmc_can_gpio_cd(host->slot->mmc) ||
3406 !mmc_card_is_removable(host->slot->mmc))) {
3407 ret = clk_prepare_enable(host->biu_clk);
3412 ret = clk_prepare_enable(host->ciu_clk);
3416 if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS)) {
3417 clk_disable_unprepare(host->ciu_clk);
3422 if (host->use_dma && host->dma_ops->init)
3423 host->dma_ops->init(host);
3426 * Restore the initial value at FIFOTH register
3427 * And Invalidate the prev_blksz with zero
3429 mci_writel(host, FIFOTH, host->fifoth_val);
3430 host->prev_blksz = 0;
3432 /* Put in max timeout */
3433 mci_writel(host, TMOUT, 0xFFFFFFFF);
3435 mci_writel(host, RINTSTS, 0xFFFFFFFF);
3436 mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
3437 SDMMC_INT_TXDR | SDMMC_INT_RXDR |
3438 DW_MCI_ERROR_FLAGS);
3439 mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
3442 if (host->slot->mmc->pm_flags & MMC_PM_KEEP_POWER)
3443 dw_mci_set_ios(host->slot->mmc, &host->slot->mmc->ios);
3445 /* Force setup bus to guarantee available clock output */
3446 dw_mci_setup_bus(host->slot, true);
3448 /* Re-enable SDIO interrupts. */
3449 if (sdio_irq_claimed(host->slot->mmc))
3450 __dw_mci_enable_sdio_irq(host->slot, 1);
3452 /* Now that slots are all setup, we can enable card detect */
3453 dw_mci_enable_cd(host);
3459 (mmc_can_gpio_cd(host->slot->mmc) ||
3460 !mmc_card_is_removable(host->slot->mmc)))
3461 clk_disable_unprepare(host->biu_clk);
3465 EXPORT_SYMBOL(dw_mci_runtime_resume);
3466 #endif /* CONFIG_PM */
3468 static int __init dw_mci_init(void)
3470 pr_info("Synopsys Designware Multimedia Card Interface Driver\n");
3474 static void __exit dw_mci_exit(void)
3478 module_init(dw_mci_init);
3479 module_exit(dw_mci_exit);
3481 MODULE_DESCRIPTION("DW Multimedia Card Interface driver");
3482 MODULE_AUTHOR("NXP Semiconductor VietNam");
3483 MODULE_AUTHOR("Imagination Technologies Ltd");
3484 MODULE_LICENSE("GPL v2");