drivers/macintosh/windfarm_pm121.c

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * Windfarm PowerMac thermal control. iMac G5 iSight
   4  *
   5  * (c) Copyright 2007 Étienne Bersac <bersace@gmail.com>
   6  *
   7  * Bits & pieces from windfarm_pm81.c by (c) Copyright 2005 Benjamin
   8  * Herrenschmidt, IBM Corp. <benh@kernel.crashing.org>
   9  *
  10  * PowerMac12,1
  11  * ============
  12  *
  13  * The algorithm used is the PID control algorithm, used the same way
  14  * the published Darwin code does, using the same values that are
  15  * present in the Darwin 8.10 snapshot property lists (note however
  16  * that none of the code has been re-used, it's a complete
  17  * re-implementation
  18  *
  19  * There is two models using PowerMac12,1. Model 2 is iMac G5 iSight
  20  * 17" while Model 3 is iMac G5 20". They do have both the same
  21  * controls with a tiny difference. The control-ids of hard-drive-fan
  22  * and cpu-fan is swapped.
  23  *
  24  * Target Correction :
  25  *
  26  * controls have a target correction calculated as :
  27  *
  28  * new_min = ((((average_power * slope) >> 16) + offset) >> 16) + min_value
  29  * new_value = max(new_value, max(new_min, 0))
  30  *
  31  * OD Fan control correction.
  32  *
  33  * # model_id: 2
  34  *   offset             : -19563152
  35  *   slope              :  1956315
  36  *
  37  * # model_id: 3
  38  *   offset             : -15650652
  39  *   slope              :  1565065
  40  *
  41  * HD Fan control correction.
  42  *
  43  * # model_id: 2
  44  *   offset             : -15650652
  45  *   slope              :  1565065
  46  *
  47  * # model_id: 3
  48  *   offset             : -19563152
  49  *   slope              :  1956315
  50  *
  51  * CPU Fan control correction.
  52  *
  53  * # model_id: 2
  54  *   offset             : -25431900
  55  *   slope              :  2543190
  56  *
  57  * # model_id: 3
  58  *   offset             : -15650652
  59  *   slope              :  1565065
  60  *
  61  * Target rubber-banding :
  62  *
  63  * Some controls have a target correction which depends on another
  64  * control value. The correction is computed in the following way :
  65  *
  66  * new_min = ref_value * slope + offset
  67  *
  68  * ref_value is the value of the reference control. If new_min is
  69  * greater than 0, then we correct the target value using :
  70  *
  71  * new_target = max (new_target, new_min >> 16)
  72  *
  73  * # model_id : 2
  74  *   control    : cpu-fan
  75  *   ref        : optical-drive-fan
  76  *   offset     : -15650652
  77  *   slope      : 1565065
  78  *
  79  * # model_id : 3
  80  *   control    : optical-drive-fan
  81  *   ref        : hard-drive-fan
  82  *   offset     : -32768000
  83  *   slope      : 65536
  84  *
  85  * In order to have the moste efficient correction with those
  86  * dependencies, we must trigger HD loop before OD loop before CPU
  87  * loop.
  88  *
  89  * The various control loops found in Darwin config file are:
  90  *
  91  * HD Fan control loop.
  92  *
  93  * # model_id: 2
  94  *   control        : hard-drive-fan
  95  *   sensor         : hard-drive-temp
  96  *   PID params     : G_d = 0x00000000
  97  *                    G_p = 0x002D70A3
  98  *                    G_r = 0x00019999
  99  *                    History = 2 entries
 100  *                    Input target = 0x370000
 101  *                    Interval = 5s
 102  *
 103  * # model_id: 3
 104  *   control        : hard-drive-fan
 105  *   sensor         : hard-drive-temp
 106  *   PID params     : G_d = 0x00000000
 107  *                    G_p = 0x002170A3
 108  *                    G_r = 0x00019999
 109  *                    History = 2 entries
 110  *                    Input target = 0x370000
 111  *                    Interval = 5s
 112  *
 113  * OD Fan control loop.
 114  *
 115  * # model_id: 2
 116  *   control        : optical-drive-fan
 117  *   sensor         : optical-drive-temp
 118  *   PID params     : G_d = 0x00000000
 119  *                    G_p = 0x001FAE14
 120  *                    G_r = 0x00019999
 121  *                    History = 2 entries
 122  *                    Input target = 0x320000
 123  *                    Interval = 5s
 124  *
 125  * # model_id: 3
 126  *   control        : optical-drive-fan
 127  *   sensor         : optical-drive-temp
 128  *   PID params     : G_d = 0x00000000
 129  *                    G_p = 0x001FAE14
 130  *                    G_r = 0x00019999
 131  *                    History = 2 entries
 132  *                    Input target = 0x320000
 133  *                    Interval = 5s
 134  *
 135  * GPU Fan control loop.
 136  *
 137  * # model_id: 2
 138  *   control        : hard-drive-fan
 139  *   sensor         : gpu-temp
 140  *   PID params     : G_d = 0x00000000
 141  *                    G_p = 0x002A6666
 142  *                    G_r = 0x00019999
 143  *                    History = 2 entries
 144  *                    Input target = 0x5A0000
 145  *                    Interval = 5s
 146  *
 147  * # model_id: 3
 148  *   control        : cpu-fan
 149  *   sensor         : gpu-temp
 150  *   PID params     : G_d = 0x00000000
 151  *                    G_p = 0x0010CCCC
 152  *                    G_r = 0x00019999
 153  *                    History = 2 entries
 154  *                    Input target = 0x500000
 155  *                    Interval = 5s
 156  *
 157  * KODIAK (aka northbridge) Fan control loop.
 158  *
 159  * # model_id: 2
 160  *   control        : optical-drive-fan
 161  *   sensor         : north-bridge-temp
 162  *   PID params     : G_d = 0x00000000
 163  *                    G_p = 0x003BD70A
 164  *                    G_r = 0x00019999
 165  *                    History = 2 entries
 166  *                    Input target = 0x550000
 167  *                    Interval = 5s
 168  *
 169  * # model_id: 3
 170  *   control        : hard-drive-fan
 171  *   sensor         : north-bridge-temp
 172  *   PID params     : G_d = 0x00000000
 173  *                    G_p = 0x0030F5C2
 174  *                    G_r = 0x00019999
 175  *                    History = 2 entries
 176  *                    Input target = 0x550000
 177  *                    Interval = 5s
 178  *
 179  * CPU Fan control loop.
 180  *
 181  *   control        : cpu-fan
 182  *   sensors        : cpu-temp, cpu-power
 183  *   PID params     : from SDB partition
 184  *
 185  * CPU Slew control loop.
 186  *
 187  *   control        : cpufreq-clamp
 188  *   sensor         : cpu-temp
 189  */
 190
 191 #undef  DEBUG
 192
 193 #include <linux/types.h>
 194 #include <linux/errno.h>
 195 #include <linux/kernel.h>
 196 #include <linux/delay.h>
 197 #include <linux/slab.h>
 198 #include <linux/init.h>
 199 #include <linux/spinlock.h>
 200 #include <linux/wait.h>
 201 #include <linux/kmod.h>
 202 #include <linux/device.h>
 203 #include <linux/platform_device.h>
 204 #include <linux/of.h>
 205
 206 #include <asm/machdep.h>
 207 #include <asm/io.h>
 208 #include <asm/sections.h>
 209 #include <asm/smu.h>
 210
 211 #include "windfarm.h"
 212 #include "windfarm_pid.h"
 213
 214 #define VERSION "0.3"
 215
 216 static int pm121_mach_model;    /* machine model id */
 217
 218 /* Controls & sensors */
 219 static struct wf_sensor *sensor_cpu_power;
 220 static struct wf_sensor *sensor_cpu_temp;
 221 static struct wf_sensor *sensor_cpu_voltage;
 222 static struct wf_sensor *sensor_cpu_current;
 223 static struct wf_sensor *sensor_gpu_temp;
 224 static struct wf_sensor *sensor_north_bridge_temp;
 225 static struct wf_sensor *sensor_hard_drive_temp;
 226 static struct wf_sensor *sensor_optical_drive_temp;
 227 static struct wf_sensor *sensor_incoming_air_temp; /* unused ! */
 228
 229 enum {
 230         FAN_CPU,
 231         FAN_HD,
 232         FAN_OD,
 233         CPUFREQ,
 234         N_CONTROLS
 235 };
 236 static struct wf_control *controls[N_CONTROLS] = {};
 237
 238 /* Set to kick the control loop into life */
 239 static int pm121_all_controls_ok, pm121_all_sensors_ok;
 240 static bool pm121_started;
 241
 242 enum {
 243         FAILURE_FAN             = 1 << 0,
 244         FAILURE_SENSOR          = 1 << 1,
 245         FAILURE_OVERTEMP        = 1 << 2
 246 };
 247
 248 /* All sys loops. Note the HD before the OD loop in order to have it
 249    run before. */
 250 enum {
 251         LOOP_GPU,               /* control = hd or cpu, but luckily,
 252                                    it doesn't matter */
 253         LOOP_HD,                /* control = hd */
 254         LOOP_KODIAK,            /* control = hd or od */
 255         LOOP_OD,                /* control = od */
 256         N_LOOPS
 257 };
 258
 259 static const char *loop_names[N_LOOPS] = {
 260         "GPU",
 261         "HD",
 262         "KODIAK",
 263         "OD",
 264 };
 265
 266 #define PM121_NUM_CONFIGS       2
 267
 268 static unsigned int pm121_failure_state;
 269 static int pm121_readjust, pm121_skipping;
 270 static bool pm121_overtemp;
 271 static s32 average_power;
 272
 273 struct pm121_correction {
 274         int     offset;
 275         int     slope;
 276 };
 277
 278 static struct pm121_correction corrections[N_CONTROLS][PM121_NUM_CONFIGS] = {
 279         /* FAN_OD */
 280         {
 281                 /* MODEL 2 */
 282                 { .offset       = -19563152,
 283                   .slope        =  1956315
 284                 },
 285                 /* MODEL 3 */
 286                 { .offset       = -15650652,
 287                   .slope        =  1565065
 288                 },
 289         },
 290         /* FAN_HD */
 291         {
 292                 /* MODEL 2 */
 293                 { .offset       = -15650652,
 294                   .slope        =  1565065
 295                 },
 296                 /* MODEL 3 */
 297                 { .offset       = -19563152,
 298                   .slope        =  1956315
 299                 },
 300         },
 301         /* FAN_CPU */
 302         {
 303                 /* MODEL 2 */
 304                 { .offset       = -25431900,
 305                   .slope        =  2543190
 306                 },
 307                 /* MODEL 3 */
 308                 { .offset       = -15650652,
 309                   .slope        =  1565065
 310                 },
 311         },
 312         /* CPUFREQ has no correction (and is not implemented at all) */
 313 };
 314
 315 struct pm121_connection {
 316         unsigned int    control_id;
 317         unsigned int    ref_id;
 318         struct pm121_correction correction;
 319 };
 320
 321 static struct pm121_connection pm121_connections[] = {
 322         /* MODEL 2 */
 323         { .control_id   = FAN_CPU,
 324           .ref_id       = FAN_OD,
 325           { .offset     = -32768000,
 326             .slope      =  65536
 327           }
 328         },
 329         /* MODEL 3 */
 330         { .control_id   = FAN_OD,
 331           .ref_id       = FAN_HD,
 332           { .offset     = -32768000,
 333             .slope      =  65536
 334           }
 335         },
 336 };
 337
 338 /* pointer to the current model connection */
 339 static struct pm121_connection *pm121_connection;
 340
 341 /*
 342  * ****** System Fans Control Loop ******
 343  *
 344  */
 345
 346 /* Since each loop handles only one control and we want to avoid
 347  * writing virtual control, we store the control correction with the
 348  * loop params. Some data are not set, there are common to all loop
 349  * and thus, hardcoded.
 350  */
 351 struct pm121_sys_param {
 352         /* purely informative since we use mach_model-2 as index */
 353         int                     model_id;
 354         struct wf_sensor        **sensor; /* use sensor_id instead ? */
 355         s32                     gp, itarget;
 356         unsigned int            control_id;
 357 };
 358
 359 static struct pm121_sys_param
 360 pm121_sys_all_params[N_LOOPS][PM121_NUM_CONFIGS] = {
 361         /* GPU Fan control loop */
 362         {
 363                 { .model_id     = 2,
 364                   .sensor       = &sensor_gpu_temp,
 365                   .gp           = 0x002A6666,
 366                   .itarget      = 0x5A0000,
 367                   .control_id   = FAN_HD,
 368                 },
 369                 { .model_id     = 3,
 370                   .sensor       = &sensor_gpu_temp,
 371                   .gp           = 0x0010CCCC,
 372                   .itarget      = 0x500000,
 373                   .control_id   = FAN_CPU,
 374                 },
 375         },
 376         /* HD Fan control loop */
 377         {
 378                 { .model_id     = 2,
 379                   .sensor       = &sensor_hard_drive_temp,
 380                   .gp           = 0x002D70A3,
 381                   .itarget      = 0x370000,
 382                   .control_id   = FAN_HD,
 383                 },
 384                 { .model_id     = 3,
 385                   .sensor       = &sensor_hard_drive_temp,
 386                   .gp           = 0x002170A3,
 387                   .itarget      = 0x370000,
 388                   .control_id   = FAN_HD,
 389                 },
 390         },
 391         /* KODIAK Fan control loop */
 392         {
 393                 { .model_id     = 2,
 394                   .sensor       = &sensor_north_bridge_temp,
 395                   .gp           = 0x003BD70A,
 396                   .itarget      = 0x550000,
 397                   .control_id   = FAN_OD,
 398                 },
 399                 { .model_id     = 3,
 400                   .sensor       = &sensor_north_bridge_temp,
 401                   .gp           = 0x0030F5C2,
 402                   .itarget      = 0x550000,
 403                   .control_id   = FAN_HD,
 404                 },
 405         },
 406         /* OD Fan control loop */
 407         {
 408                 { .model_id     = 2,
 409                   .sensor       = &sensor_optical_drive_temp,
 410                   .gp           = 0x001FAE14,
 411                   .itarget      = 0x320000,
 412                   .control_id   = FAN_OD,
 413                 },
 414                 { .model_id     = 3,
 415                   .sensor       = &sensor_optical_drive_temp,
 416                   .gp           = 0x001FAE14,
 417                   .itarget      = 0x320000,
 418                   .control_id   = FAN_OD,
 419                 },
 420         },
 421 };
 422
 423 /* the hardcoded values */
 424 #define PM121_SYS_GD            0x00000000
 425 #define PM121_SYS_GR            0x00019999
 426 #define PM121_SYS_HISTORY_SIZE  2
 427 #define PM121_SYS_INTERVAL      5
 428
 429 /* State data used by the system fans control loop
 430  */
 431 struct pm121_sys_state {
 432         int                     ticks;
 433         s32                     setpoint;
 434         struct wf_pid_state     pid;
 435 };
 436
 437 static struct pm121_sys_state *pm121_sys_state[N_LOOPS] = {};
 438
 439 /*
 440  * ****** CPU Fans Control Loop ******
 441  *
 442  */
 443
 444 #define PM121_CPU_INTERVAL      1
 445
 446 /* State data used by the cpu fans control loop
 447  */
 448 struct pm121_cpu_state {
 449         int                     ticks;
 450         s32                     setpoint;
 451         struct wf_cpu_pid_state pid;
 452 };
 453
 454 static struct pm121_cpu_state *pm121_cpu_state;
 455
 456
 457
 458 /*
 459  * ***** Implementation *****
 460  *
 461  */
 462
 463 /* correction the value using the output-low-bound correction algo */
 464 static s32 pm121_correct(s32 new_setpoint,
 465                          unsigned int control_id,
 466                          s32 min)
 467 {
 468         s32 new_min;
 469         struct pm121_correction *correction;
 470         correction = &corrections[control_id][pm121_mach_model - 2];
 471
 472         new_min = (average_power * correction->slope) >> 16;
 473         new_min += correction->offset;
 474         new_min = (new_min >> 16) + min;
 475
 476         return max3(new_setpoint, new_min, 0);
 477 }
 478
 479 static s32 pm121_connect(unsigned int control_id, s32 setpoint)
 480 {
 481         s32 new_min, value, new_setpoint;
 482
 483         if (pm121_connection->control_id == control_id) {
 484                 controls[control_id]->ops->get_value(controls[control_id],
 485                                                      &value);
 486                 new_min = value * pm121_connection->correction.slope;
 487                 new_min += pm121_connection->correction.offset;
 488                 if (new_min > 0) {
 489                         new_setpoint = max(setpoint, (new_min >> 16));
 490                         if (new_setpoint != setpoint) {
 491                                 pr_debug("pm121: %s depending on %s, "
 492                                          "corrected from %d to %d RPM\n",
 493                                          controls[control_id]->name,
 494                                          controls[pm121_connection->ref_id]->name,
 495                                          (int) setpoint, (int) new_setpoint);
 496                         }
 497                 } else
 498                         new_setpoint = setpoint;
 499         }
 500         /* no connection */
 501         else
 502                 new_setpoint = setpoint;
 503
 504         return new_setpoint;
 505 }
 506
 507 /* FAN LOOPS */
 508 static void pm121_create_sys_fans(int loop_id)
 509 {
 510         struct pm121_sys_param *param = NULL;
 511         struct wf_pid_param pid_param;
 512         struct wf_control *control = NULL;
 513         int i;
 514
 515         /* First, locate the params for this model */
 516         for (i = 0; i < PM121_NUM_CONFIGS; i++) {
 517                 if (pm121_sys_all_params[loop_id][i].model_id == pm121_mach_model) {
 518                         param = &(pm121_sys_all_params[loop_id][i]);
 519                         break;
 520                 }
 521         }
 522
 523         /* No params found, put fans to max */
 524         if (param == NULL) {
 525                 printk(KERN_WARNING "pm121: %s fan config not found "
 526                        " for this machine model\n",
 527                        loop_names[loop_id]);
 528                 goto fail;
 529         }
 530
 531         control = controls[param->control_id];
 532
 533         /* Alloc & initialize state */
 534         pm121_sys_state[loop_id] = kmalloc(sizeof(struct pm121_sys_state),
 535                                            GFP_KERNEL);
 536         if (pm121_sys_state[loop_id] == NULL) {
 537                 printk(KERN_WARNING "pm121: Memory allocation error\n");
 538                 goto fail;
 539         }
 540         pm121_sys_state[loop_id]->ticks = 1;
 541
 542         /* Fill PID params */
 543         pid_param.gd            = PM121_SYS_GD;
 544         pid_param.gp            = param->gp;
 545         pid_param.gr            = PM121_SYS_GR;
 546         pid_param.interval      = PM121_SYS_INTERVAL;
 547         pid_param.history_len   = PM121_SYS_HISTORY_SIZE;
 548         pid_param.itarget       = param->itarget;
 549         if(control)
 550         {
 551                 pid_param.min           = control->ops->get_min(control);
 552                 pid_param.max           = control->ops->get_max(control);
 553         } else {
 554                 /*
 555                  * This is probably not the right!?
 556                  * Perhaps goto fail  if control == NULL  above?
 557                  */
 558                 pid_param.min           = 0;
 559                 pid_param.max           = 0;
 560         }
 561
 562         wf_pid_init(&pm121_sys_state[loop_id]->pid, &pid_param);
 563
 564         pr_debug("pm121: %s Fan control loop initialized.\n"
 565                  "       itarged=%d.%03d, min=%d RPM, max=%d RPM\n",
 566                  loop_names[loop_id], FIX32TOPRINT(pid_param.itarget),
 567                  pid_param.min, pid_param.max);
 568         return;
 569
 570  fail:
 571         /* note that this is not optimal since another loop may still
 572            control the same control */
 573         printk(KERN_WARNING "pm121: failed to set up %s loop "
 574                "setting \"%s\" to max speed.\n",
 575                loop_names[loop_id], control ? control->name : "uninitialized value");
 576
 577         if (control)
 578                 wf_control_set_max(control);
 579 }
 580
 581 static void pm121_sys_fans_tick(int loop_id)
 582 {
 583         struct pm121_sys_param *param;
 584         struct pm121_sys_state *st;
 585         struct wf_sensor *sensor;
 586         struct wf_control *control;
 587         s32 temp, new_setpoint;
 588         int rc;
 589
 590         param = &(pm121_sys_all_params[loop_id][pm121_mach_model-2]);
 591         st = pm121_sys_state[loop_id];
 592         sensor = *(param->sensor);
 593         control = controls[param->control_id];
 594
 595         if (--st->ticks != 0) {
 596                 if (pm121_readjust)
 597                         goto readjust;
 598                 return;
 599         }
 600         st->ticks = PM121_SYS_INTERVAL;
 601
 602         rc = sensor->ops->get_value(sensor, &temp);
 603         if (rc) {
 604                 printk(KERN_WARNING "windfarm: %s sensor error %d\n",
 605                        sensor->name, rc);
 606                 pm121_failure_state |= FAILURE_SENSOR;
 607                 return;
 608         }
 609
 610         pr_debug("pm121: %s Fan tick ! %s: %d.%03d\n",
 611                  loop_names[loop_id], sensor->name,
 612                  FIX32TOPRINT(temp));
 613
 614         new_setpoint = wf_pid_run(&st->pid, temp);
 615
 616         /* correction */
 617         new_setpoint = pm121_correct(new_setpoint,
 618                                      param->control_id,
 619                                      st->pid.param.min);
 620         /* linked corretion */
 621         new_setpoint = pm121_connect(param->control_id, new_setpoint);
 622
 623         if (new_setpoint == st->setpoint)
 624                 return;
 625         st->setpoint = new_setpoint;
 626         pr_debug("pm121: %s corrected setpoint: %d RPM\n",
 627                  control->name, (int)new_setpoint);
 628  readjust:
 629         if (control && pm121_failure_state == 0) {
 630                 rc = control->ops->set_value(control, st->setpoint);
 631                 if (rc) {
 632                         printk(KERN_WARNING "windfarm: %s fan error %d\n",
 633                                control->name, rc);
 634                         pm121_failure_state |= FAILURE_FAN;
 635                 }
 636         }
 637 }
 638
 639
 640 /* CPU LOOP */
 641 static void pm121_create_cpu_fans(void)
 642 {
 643         struct wf_cpu_pid_param pid_param;
 644         const struct smu_sdbp_header *hdr;
 645         struct smu_sdbp_cpupiddata *piddata;
 646         struct smu_sdbp_fvt *fvt;
 647         struct wf_control *fan_cpu;
 648         s32 tmax, tdelta, maxpow, powadj;
 649
 650         fan_cpu = controls[FAN_CPU];
 651
 652         /* First, locate the PID params in SMU SBD */
 653         hdr = smu_get_sdb_partition(SMU_SDB_CPUPIDDATA_ID, NULL);
 654         if (hdr == 0) {
 655                 printk(KERN_WARNING "pm121: CPU PID fan config not found.\n");
 656                 goto fail;
 657         }
 658         piddata = (struct smu_sdbp_cpupiddata *)&hdr[1];
 659
 660         /* Get the FVT params for operating point 0 (the only supported one
 661          * for now) in order to get tmax
 662          */
 663         hdr = smu_get_sdb_partition(SMU_SDB_FVT_ID, NULL);
 664         if (hdr) {
 665                 fvt = (struct smu_sdbp_fvt *)&hdr[1];
 666                 tmax = ((s32)fvt->maxtemp) << 16;
 667         } else
 668                 tmax = 0x5e0000; /* 94 degree default */
 669
 670         /* Alloc & initialize state */
 671         pm121_cpu_state = kmalloc(sizeof(struct pm121_cpu_state),
 672                                   GFP_KERNEL);
 673         if (pm121_cpu_state == NULL)
 674                 goto fail;
 675         pm121_cpu_state->ticks = 1;
 676
 677         /* Fill PID params */
 678         pid_param.interval = PM121_CPU_INTERVAL;
 679         pid_param.history_len = piddata->history_len;
 680         if (pid_param.history_len > WF_CPU_PID_MAX_HISTORY) {
 681                 printk(KERN_WARNING "pm121: History size overflow on "
 682                        "CPU control loop (%d)\n", piddata->history_len);
 683                 pid_param.history_len = WF_CPU_PID_MAX_HISTORY;
 684         }
 685         pid_param.gd = piddata->gd;
 686         pid_param.gp = piddata->gp;
 687         pid_param.gr = piddata->gr / pid_param.history_len;
 688
 689         tdelta = ((s32)piddata->target_temp_delta) << 16;
 690         maxpow = ((s32)piddata->max_power) << 16;
 691         powadj = ((s32)piddata->power_adj) << 16;
 692
 693         pid_param.tmax = tmax;
 694         pid_param.ttarget = tmax - tdelta;
 695         pid_param.pmaxadj = maxpow - powadj;
 696
 697         pid_param.min = fan_cpu->ops->get_min(fan_cpu);
 698         pid_param.max = fan_cpu->ops->get_max(fan_cpu);
 699
 700         wf_cpu_pid_init(&pm121_cpu_state->pid, &pid_param);
 701
 702         pr_debug("pm121: CPU Fan control initialized.\n");
 703         pr_debug("       ttarget=%d.%03d, tmax=%d.%03d, min=%d RPM, max=%d RPM,\n",
 704                  FIX32TOPRINT(pid_param.ttarget), FIX32TOPRINT(pid_param.tmax),
 705                  pid_param.min, pid_param.max);
 706
 707         return;
 708
 709  fail:
 710         printk(KERN_WARNING "pm121: CPU fan config not found, max fan speed\n");
 711
 712         if (controls[CPUFREQ])
 713                 wf_control_set_max(controls[CPUFREQ]);
 714         if (fan_cpu)
 715                 wf_control_set_max(fan_cpu);
 716 }
 717
 718
 719 static void pm121_cpu_fans_tick(struct pm121_cpu_state *st)
 720 {
 721         s32 new_setpoint, temp, power;
 722         struct wf_control *fan_cpu = NULL;
 723         int rc;
 724
 725         if (--st->ticks != 0) {
 726                 if (pm121_readjust)
 727                         goto readjust;
 728                 return;
 729         }
 730         st->ticks = PM121_CPU_INTERVAL;
 731
 732         fan_cpu = controls[FAN_CPU];
 733
 734         rc = sensor_cpu_temp->ops->get_value(sensor_cpu_temp, &temp);
 735         if (rc) {
 736                 printk(KERN_WARNING "pm121: CPU temp sensor error %d\n",
 737                        rc);
 738                 pm121_failure_state |= FAILURE_SENSOR;
 739                 return;
 740         }
 741
 742         rc = sensor_cpu_power->ops->get_value(sensor_cpu_power, &power);
 743         if (rc) {
 744                 printk(KERN_WARNING "pm121: CPU power sensor error %d\n",
 745                        rc);
 746                 pm121_failure_state |= FAILURE_SENSOR;
 747                 return;
 748         }
 749
 750         pr_debug("pm121: CPU Fans tick ! CPU temp: %d.%03d°C, power: %d.%03d\n",
 751                  FIX32TOPRINT(temp), FIX32TOPRINT(power));
 752
 753         if (temp > st->pid.param.tmax)
 754                 pm121_failure_state |= FAILURE_OVERTEMP;
 755
 756         new_setpoint = wf_cpu_pid_run(&st->pid, power, temp);
 757
 758         /* correction */
 759         new_setpoint = pm121_correct(new_setpoint,
 760                                      FAN_CPU,
 761                                      st->pid.param.min);
 762
 763         /* connected correction */
 764         new_setpoint = pm121_connect(FAN_CPU, new_setpoint);
 765
 766         if (st->setpoint == new_setpoint)
 767                 return;
 768         st->setpoint = new_setpoint;
 769         pr_debug("pm121: CPU corrected setpoint: %d RPM\n", (int)new_setpoint);
 770
 771  readjust:
 772         if (fan_cpu && pm121_failure_state == 0) {
 773                 rc = fan_cpu->ops->set_value(fan_cpu, st->setpoint);
 774                 if (rc) {
 775                         printk(KERN_WARNING "pm121: %s fan error %d\n",
 776                                fan_cpu->name, rc);
 777                         pm121_failure_state |= FAILURE_FAN;
 778                 }
 779         }
 780 }
 781
 782 /*
 783  * ****** Common ******
 784  *
 785  */
 786
 787 static void pm121_tick(void)
 788 {
 789         unsigned int last_failure = pm121_failure_state;
 790         unsigned int new_failure;
 791         s32 total_power;
 792         int i;
 793
 794         if (!pm121_started) {
 795                 pr_debug("pm121: creating control loops !\n");
 796                 for (i = 0; i < N_LOOPS; i++)
 797                         pm121_create_sys_fans(i);
 798
 799                 pm121_create_cpu_fans();
 800                 pm121_started = true;
 801         }
 802
 803         /* skipping ticks */
 804         if (pm121_skipping && --pm121_skipping)
 805                 return;
 806
 807         /* compute average power */
 808         total_power = 0;
 809         for (i = 0; i < pm121_cpu_state->pid.param.history_len; i++)
 810                 total_power += pm121_cpu_state->pid.powers[i];
 811
 812         average_power = total_power / pm121_cpu_state->pid.param.history_len;
 813
 814
 815         pm121_failure_state = 0;
 816         for (i = 0 ; i < N_LOOPS; i++) {
 817                 if (pm121_sys_state[i])
 818                         pm121_sys_fans_tick(i);
 819         }
 820
 821         if (pm121_cpu_state)
 822                 pm121_cpu_fans_tick(pm121_cpu_state);
 823
 824         pm121_readjust = 0;
 825         new_failure = pm121_failure_state & ~last_failure;
 826
 827         /* If entering failure mode, clamp cpufreq and ramp all
 828          * fans to full speed.
 829          */
 830         if (pm121_failure_state && !last_failure) {
 831                 for (i = 0; i < N_CONTROLS; i++) {
 832                         if (controls[i])
 833                                 wf_control_set_max(controls[i]);
 834                 }
 835         }
 836
 837         /* If leaving failure mode, unclamp cpufreq and readjust
 838          * all fans on next iteration
 839          */
 840         if (!pm121_failure_state && last_failure) {
 841                 if (controls[CPUFREQ])
 842                         wf_control_set_min(controls[CPUFREQ]);
 843                 pm121_readjust = 1;
 844         }
 845
 846         /* Overtemp condition detected, notify and start skipping a couple
 847          * ticks to let the temperature go down
 848          */
 849         if (new_failure & FAILURE_OVERTEMP) {
 850                 wf_set_overtemp();
 851                 pm121_skipping = 2;
 852                 pm121_overtemp = true;
 853         }
 854
 855         /* We only clear the overtemp condition if overtemp is cleared
 856          * _and_ no other failure is present. Since a sensor error will
 857          * clear the overtemp condition (can't measure temperature) at
 858          * the control loop levels, but we don't want to keep it clear
 859          * here in this case
 860          */
 861         if (!pm121_failure_state && pm121_overtemp) {
 862                 wf_clear_overtemp();
 863                 pm121_overtemp = false;
 864         }
 865 }
 866
 867
 868 static struct wf_control* pm121_register_control(struct wf_control *ct,
 869                                                  const char *match,
 870                                                  unsigned int id)
 871 {
 872         if (controls[id] == NULL && !strcmp(ct->name, match)) {
 873                 if (wf_get_control(ct) == 0)
 874                         controls[id] = ct;
 875         }
 876         return controls[id];
 877 }
 878
 879 static void pm121_new_control(struct wf_control *ct)
 880 {
 881         int all = 1;
 882
 883         if (pm121_all_controls_ok)
 884                 return;
 885
 886         all = pm121_register_control(ct, "optical-drive-fan", FAN_OD) && all;
 887         all = pm121_register_control(ct, "hard-drive-fan", FAN_HD) && all;
 888         all = pm121_register_control(ct, "cpu-fan", FAN_CPU) && all;
 889         all = pm121_register_control(ct, "cpufreq-clamp", CPUFREQ) && all;
 890
 891         if (all)
 892                 pm121_all_controls_ok = 1;
 893 }
 894
 895
 896
 897
 898 static struct wf_sensor* pm121_register_sensor(struct wf_sensor *sensor,
 899                                                const char *match,
 900                                                struct wf_sensor **var)
 901 {
 902         if (*var == NULL && !strcmp(sensor->name, match)) {
 903                 if (wf_get_sensor(sensor) == 0)
 904                         *var = sensor;
 905         }
 906         return *var;
 907 }
 908
 909 static void pm121_new_sensor(struct wf_sensor *sr)
 910 {
 911         int all = 1;
 912
 913         if (pm121_all_sensors_ok)
 914                 return;
 915
 916         all = pm121_register_sensor(sr, "cpu-temp",
 917                                     &sensor_cpu_temp) && all;
 918         all = pm121_register_sensor(sr, "cpu-current",
 919                                     &sensor_cpu_current) && all;
 920         all = pm121_register_sensor(sr, "cpu-voltage",
 921                                     &sensor_cpu_voltage) && all;
 922         all = pm121_register_sensor(sr, "cpu-power",
 923                                     &sensor_cpu_power) && all;
 924         all = pm121_register_sensor(sr, "hard-drive-temp",
 925                                     &sensor_hard_drive_temp) && all;
 926         all = pm121_register_sensor(sr, "optical-drive-temp",
 927                                     &sensor_optical_drive_temp) && all;
 928         all = pm121_register_sensor(sr, "incoming-air-temp",
 929                                     &sensor_incoming_air_temp) && all;
 930         all = pm121_register_sensor(sr, "north-bridge-temp",
 931                                     &sensor_north_bridge_temp) && all;
 932         all = pm121_register_sensor(sr, "gpu-temp",
 933                                     &sensor_gpu_temp) && all;
 934
 935         if (all)
 936                 pm121_all_sensors_ok = 1;
 937 }
 938
 939
 940
 941 static int pm121_notify(struct notifier_block *self,
 942                         unsigned long event, void *data)
 943 {
 944         switch (event) {
 945         case WF_EVENT_NEW_CONTROL:
 946                 pr_debug("pm121: new control %s detected\n",
 947                          ((struct wf_control *)data)->name);
 948                 pm121_new_control(data);
 949                 break;
 950         case WF_EVENT_NEW_SENSOR:
 951                 pr_debug("pm121: new sensor %s detected\n",
 952                          ((struct wf_sensor *)data)->name);
 953                 pm121_new_sensor(data);
 954                 break;
 955         case WF_EVENT_TICK:
 956                 if (pm121_all_controls_ok && pm121_all_sensors_ok)
 957                         pm121_tick();
 958                 break;
 959         }
 960
 961         return 0;
 962 }
 963
 964 static struct notifier_block pm121_events = {
 965         .notifier_call  = pm121_notify,
 966 };
 967
 968 static int pm121_init_pm(void)
 969 {
 970         const struct smu_sdbp_header *hdr;
 971
 972         hdr = smu_get_sdb_partition(SMU_SDB_SENSORTREE_ID, NULL);
 973         if (hdr != 0) {
 974                 struct smu_sdbp_sensortree *st =
 975                         (struct smu_sdbp_sensortree *)&hdr[1];
 976                 pm121_mach_model = st->model_id;
 977         }
 978
 979         pm121_connection = &pm121_connections[pm121_mach_model - 2];
 980
 981         printk(KERN_INFO "pm121: Initializing for iMac G5 iSight model ID %d\n",
 982                pm121_mach_model);
 983
 984         return 0;
 985 }
 986
 987
 988 static int pm121_probe(struct platform_device *ddev)
 989 {
 990         wf_register_client(&pm121_events);
 991
 992         return 0;
 993 }
 994
 995 static int pm121_remove(struct platform_device *ddev)
 996 {
 997         wf_unregister_client(&pm121_events);
 998         return 0;
 999 }
1000
1001 static struct platform_driver pm121_driver = {
1002         .probe = pm121_probe,
1003         .remove = pm121_remove,
1004         .driver = {
1005                 .name = "windfarm",
1006                 .bus = &platform_bus_type,
1007         },
1008 };
1009
1010
1011 static int __init pm121_init(void)
1012 {
1013         int rc = -ENODEV;
1014
1015         if (of_machine_is_compatible("PowerMac12,1"))
1016                 rc = pm121_init_pm();
1017
1018         if (rc == 0) {
1019                 request_module("windfarm_smu_controls");
1020                 request_module("windfarm_smu_sensors");
1021                 request_module("windfarm_smu_sat");
1022                 request_module("windfarm_lm75_sensor");
1023                 request_module("windfarm_max6690_sensor");
1024                 request_module("windfarm_cpufreq_clamp");
1025                 platform_driver_register(&pm121_driver);
1026         }
1027
1028         return rc;
1029 }
1030
1031 static void __exit pm121_exit(void)
1032 {
1033
1034         platform_driver_unregister(&pm121_driver);
1035 }
1036
1037
1038 module_init(pm121_init);
1039 module_exit(pm121_exit);
1040
1041 MODULE_AUTHOR("Étienne Bersac <bersace@gmail.com>");
1042 MODULE_DESCRIPTION("Thermal control logic for iMac G5 (iSight)");
1043 MODULE_LICENSE("GPL");
1044