1 # SPDX-License-Identifier: GPL-2.0
2 source "arch/powerpc/platforms/Kconfig.cputype"
16 config ARCH_MMAP_RND_BITS_MAX
17 # On Book3S 64, the default virtual address space for 64-bit processes
18 # is 2^47 (128TB). As a maximum, allow randomisation to consume up to
19 # 32T of address space (2^45), which should ensure a reasonable gap
20 # between bottom-up and top-down allocations for applications that
21 # consume "normal" amounts of address space. Book3S 64 only supports 64K
23 default 29 if PPC_BOOK3S_64 && PPC_64K_PAGES # 29 = 45 (32T) - 16 (64K)
24 default 33 if PPC_BOOK3S_64 # 33 = 45 (32T) - 12 (4K)
26 # On all other 64-bit platforms (currently only Book3E), the virtual
27 # address space is 2^46 (64TB). Allow randomisation to consume up to 16T
28 # of address space (2^44). Only 4K page sizes are supported.
29 default 32 if 64BIT # 32 = 44 (16T) - 12 (4K)
31 # For 32-bit, use the compat values, as they're the same.
32 default ARCH_MMAP_RND_COMPAT_BITS_MAX
34 config ARCH_MMAP_RND_BITS_MIN
35 # Allow randomisation to consume up to 1GB of address space (2^30).
36 default 14 if 64BIT && PPC_64K_PAGES # 14 = 30 (1GB) - 16 (64K)
37 default 18 if 64BIT # 18 = 30 (1GB) - 12 (4K)
39 # For 32-bit, use the compat values, as they're the same.
40 default ARCH_MMAP_RND_COMPAT_BITS_MIN
42 config ARCH_MMAP_RND_COMPAT_BITS_MAX
43 # Total virtual address space for 32-bit processes is 2^31 (2GB).
44 # Allow randomisation to consume up to 512MB of address space (2^29).
45 default 11 if PPC_256K_PAGES # 11 = 29 (512MB) - 18 (256K)
46 default 13 if PPC_64K_PAGES # 13 = 29 (512MB) - 16 (64K)
47 default 15 if PPC_16K_PAGES # 15 = 29 (512MB) - 14 (16K)
48 default 17 # 17 = 29 (512MB) - 12 (4K)
50 config ARCH_MMAP_RND_COMPAT_BITS_MIN
51 # Total virtual address space for 32-bit processes is 2^31 (2GB).
52 # Allow randomisation to consume up to 8MB of address space (2^23).
53 default 5 if PPC_256K_PAGES # 5 = 23 (8MB) - 18 (256K)
54 default 7 if PPC_64K_PAGES # 7 = 23 (8MB) - 16 (64K)
55 default 9 if PPC_16K_PAGES # 9 = 23 (8MB) - 14 (16K)
56 default 11 # 11 = 23 (8MB) - 12 (4K)
58 config HAVE_SETUP_PER_CPU_AREA
61 config NEED_PER_CPU_EMBED_FIRST_CHUNK
64 config NEED_PER_CPU_PAGE_FIRST_CHUNK
68 int "Number of virtual interrupt numbers"
72 This defines the number of virtual interrupt numbers the kernel
73 can manage. Virtual interrupt numbers are what you see in
74 /proc/interrupts. If you configure your system to have too few,
75 drivers will fail to load or worse - handle with care.
79 depends on SMP && (DEBUGGER || KEXEC_CORE || HARDLOCKUP_DETECTOR)
84 depends on HARDLOCKUP_DETECTOR
85 depends on HAVE_HARDLOCKUP_DETECTOR_ARCH
88 This is a placeholder when the powerpc hardlockup detector
89 watchdog is selected (arch/powerpc/kernel/watchdog.c). It is
90 selected via the generic lockup detector menu which is why we
91 have no standalone config option for it here.
93 config STACKTRACE_SUPPORT
97 config TRACE_IRQFLAGS_SUPPORT
101 config LOCKDEP_SUPPORT
105 config GENERIC_LOCKBREAK
108 depends on SMP && PREEMPTION
110 config GENERIC_HWEIGHT
118 # Please keep this list sorted alphabetically.
120 select ARCH_32BIT_OFF_T if PPC32
121 select ARCH_ENABLE_MEMORY_HOTPLUG
122 select ARCH_ENABLE_MEMORY_HOTREMOVE
123 select ARCH_HAS_COPY_MC if PPC64
124 select ARCH_HAS_DEBUG_VIRTUAL
125 select ARCH_HAS_DEBUG_VM_PGTABLE
126 select ARCH_HAS_DEVMEM_IS_ALLOWED
127 select ARCH_HAS_DMA_MAP_DIRECT if PPC_PSERIES
128 select ARCH_HAS_ELF_RANDOMIZE
129 select ARCH_HAS_FORTIFY_SOURCE
130 select ARCH_HAS_GCOV_PROFILE_ALL
131 select ARCH_HAS_HUGEPD if HUGETLB_PAGE
133 select ARCH_HAS_MEMBARRIER_CALLBACKS
134 select ARCH_HAS_MEMBARRIER_SYNC_CORE
135 select ARCH_HAS_MEMREMAP_COMPAT_ALIGN
136 select ARCH_HAS_MMIOWB if PPC64
137 select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
138 select ARCH_HAS_PHYS_TO_DMA
139 select ARCH_HAS_PMEM_API
140 select ARCH_HAS_PTE_DEVMAP if PPC_BOOK3S_64
141 select ARCH_HAS_PTE_SPECIAL
142 select ARCH_HAS_SCALED_CPUTIME if VIRT_CPU_ACCOUNTING_NATIVE && PPC_BOOK3S_64
143 select ARCH_HAS_SET_MEMORY
144 select ARCH_HAS_STRICT_KERNEL_RWX if ((PPC_BOOK3S_64 || PPC32) && !HIBERNATION)
145 select ARCH_HAS_STRICT_MODULE_RWX if ARCH_HAS_STRICT_KERNEL_RWX && !PPC_BOOK3S_32
146 select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
147 select ARCH_HAS_UACCESS_FLUSHCACHE
148 select ARCH_HAS_UBSAN_SANITIZE_ALL
149 select ARCH_HAVE_NMI_SAFE_CMPXCHG
150 select ARCH_KEEP_MEMBLOCK
151 select ARCH_MIGHT_HAVE_PC_PARPORT
152 select ARCH_MIGHT_HAVE_PC_SERIO
153 select ARCH_OPTIONAL_KERNEL_RWX if ARCH_HAS_STRICT_KERNEL_RWX
154 select ARCH_STACKWALK
155 select ARCH_SUPPORTS_ATOMIC_RMW
156 select ARCH_SUPPORTS_DEBUG_PAGEALLOC if PPC32 || PPC_BOOK3S_64
157 select ARCH_USE_BUILTIN_BSWAP
158 select ARCH_USE_CMPXCHG_LOCKREF if PPC64
159 select ARCH_USE_MEMTEST
160 select ARCH_USE_QUEUED_RWLOCKS if PPC_QUEUED_SPINLOCKS
161 select ARCH_USE_QUEUED_SPINLOCKS if PPC_QUEUED_SPINLOCKS
162 select ARCH_WANT_IPC_PARSE_VERSION
163 select ARCH_WANT_IRQS_OFF_ACTIVATE_MM
164 select ARCH_WANT_LD_ORPHAN_WARN
165 select ARCH_WEAK_RELEASE_ACQUIRE
167 select BUILDTIME_TABLE_SORT
168 select CLONE_BACKWARDS
169 select DCACHE_WORD_ACCESS if PPC64 && CPU_LITTLE_ENDIAN
170 select DMA_OPS_BYPASS if PPC64
171 select DMA_OPS if PPC64
172 select DYNAMIC_FTRACE if FUNCTION_TRACER
173 select EDAC_ATOMIC_SCRUB
175 select GENERIC_ATOMIC64 if PPC32
176 select GENERIC_CLOCKEVENTS_BROADCAST if SMP
177 select GENERIC_CMOS_UPDATE
178 select GENERIC_CPU_AUTOPROBE
179 select GENERIC_CPU_VULNERABILITIES if PPC_BARRIER_NOSPEC
180 select GENERIC_EARLY_IOREMAP
181 select GENERIC_GETTIMEOFDAY
182 select GENERIC_IRQ_SHOW
183 select GENERIC_IRQ_SHOW_LEVEL
184 select GENERIC_PCI_IOMAP if PCI
185 select GENERIC_SMP_IDLE_THREAD
186 select GENERIC_STRNCPY_FROM_USER
187 select GENERIC_STRNLEN_USER
188 select GENERIC_TIME_VSYSCALL
189 select GENERIC_VDSO_TIME_NS
190 select HAVE_ARCH_AUDITSYSCALL
191 select HAVE_ARCH_HUGE_VMALLOC if HAVE_ARCH_HUGE_VMAP
192 select HAVE_ARCH_HUGE_VMAP if PPC_RADIX_MMU || PPC_8xx
193 select HAVE_ARCH_JUMP_LABEL
194 select HAVE_ARCH_JUMP_LABEL_RELATIVE
195 select HAVE_ARCH_KASAN if PPC32 && PPC_PAGE_SHIFT <= 14
196 select HAVE_ARCH_KASAN_VMALLOC if PPC32 && PPC_PAGE_SHIFT <= 14
197 select HAVE_ARCH_KFENCE if PPC32
198 select HAVE_ARCH_KGDB
199 select HAVE_ARCH_MMAP_RND_BITS
200 select HAVE_ARCH_MMAP_RND_COMPAT_BITS if COMPAT
201 select HAVE_ARCH_NVRAM_OPS
202 select HAVE_ARCH_SECCOMP_FILTER
203 select HAVE_ARCH_TRACEHOOK
204 select HAVE_ASM_MODVERSIONS
205 select HAVE_CONTEXT_TRACKING if PPC64
206 select HAVE_C_RECORDMCOUNT
207 select HAVE_DEBUG_KMEMLEAK
208 select HAVE_DEBUG_STACKOVERFLOW
209 select HAVE_DYNAMIC_FTRACE
210 select HAVE_DYNAMIC_FTRACE_WITH_REGS if MPROFILE_KERNEL
212 select HAVE_EFFICIENT_UNALIGNED_ACCESS if !(CPU_LITTLE_ENDIAN && POWER7_CPU)
214 select HAVE_FTRACE_MCOUNT_RECORD
215 select HAVE_FUNCTION_ERROR_INJECTION
216 select HAVE_FUNCTION_GRAPH_TRACER
217 select HAVE_FUNCTION_TRACER
218 select HAVE_GCC_PLUGINS if GCC_VERSION >= 50200 # plugin support on gcc <= 5.1 is buggy on PPC
219 select HAVE_GENERIC_VDSO
220 select HAVE_HARDLOCKUP_DETECTOR_ARCH if PPC_BOOK3S_64 && SMP
221 select HAVE_HARDLOCKUP_DETECTOR_PERF if PERF_EVENTS && HAVE_PERF_EVENTS_NMI && !HAVE_HARDLOCKUP_DETECTOR_ARCH
222 select HAVE_HW_BREAKPOINT if PERF_EVENTS && (PPC_BOOK3S || PPC_8xx)
223 select HAVE_IOREMAP_PROT
224 select HAVE_IRQ_EXIT_ON_IRQ_STACK
225 select HAVE_IRQ_TIME_ACCOUNTING
226 select HAVE_KERNEL_GZIP
227 select HAVE_KERNEL_LZMA if DEFAULT_UIMAGE
228 select HAVE_KERNEL_LZO if DEFAULT_UIMAGE
229 select HAVE_KERNEL_XZ if PPC_BOOK3S || 44x
231 select HAVE_KPROBES_ON_FTRACE
232 select HAVE_KRETPROBES
233 select HAVE_LD_DEAD_CODE_DATA_ELIMINATION
234 select HAVE_LIVEPATCH if HAVE_DYNAMIC_FTRACE_WITH_REGS
235 select HAVE_MOD_ARCH_SPECIFIC
236 select HAVE_NMI if PERF_EVENTS || (PPC64 && PPC_BOOK3S)
237 select HAVE_OPTPROBES
238 select HAVE_PERF_EVENTS
239 select HAVE_PERF_EVENTS_NMI if PPC64
240 select HAVE_PERF_REGS
241 select HAVE_PERF_USER_STACK_DUMP
242 select HAVE_REGS_AND_STACK_ACCESS_API
243 select HAVE_RELIABLE_STACKTRACE
245 select HAVE_SOFTIRQ_ON_OWN_STACK
246 select HAVE_STACKPROTECTOR if PPC32 && $(cc-option,-mstack-protector-guard=tls -mstack-protector-guard-reg=r2)
247 select HAVE_STACKPROTECTOR if PPC64 && $(cc-option,-mstack-protector-guard=tls -mstack-protector-guard-reg=r13)
248 select HAVE_SYSCALL_TRACEPOINTS
249 select HAVE_VIRT_CPU_ACCOUNTING
250 select HUGETLB_PAGE_SIZE_VARIABLE if PPC_BOOK3S_64 && HUGETLB_PAGE
251 select IOMMU_HELPER if PPC64
253 select IRQ_FORCED_THREADING
254 select MMU_GATHER_PAGE_SIZE
255 select MMU_GATHER_RCU_TABLE_FREE
256 select MODULES_USE_ELF_RELA
257 select NEED_DMA_MAP_STATE if PPC64 || NOT_COHERENT_CACHE
258 select NEED_SG_DMA_LENGTH
260 select OF_DMA_DEFAULT_COHERENT if !NOT_COHERENT_CACHE
261 select OF_EARLY_FLATTREE
262 select OLD_SIGACTION if PPC32
263 select OLD_SIGSUSPEND
264 select PCI_DOMAINS if PCI
265 select PCI_MSI_ARCH_FALLBACKS if PCI_MSI
266 select PCI_SYSCALL if PCI
267 select PPC_DAWR if PPC64
270 select STRICT_KERNEL_RWX if STRICT_MODULE_RWX
271 select SYSCTL_EXCEPTION_TRACE
272 select THREAD_INFO_IN_TASK
273 select VIRT_TO_BUS if !PPC64
275 # Please keep this list sorted alphabetically.
278 config PPC_BARRIER_NOSPEC
281 depends on PPC_BOOK3S_64 || PPC_FSL_BOOK3E
292 bool "Enable support for 32bit binaries"
294 depends on !CC_IS_CLANG || CLANG_VERSION >= 120000
295 default y if !CPU_LITTLE_ENDIAN
296 select ARCH_WANT_OLD_COMPAT_IPC
297 select COMPAT_OLD_SIGACTION
299 config SYSVIPC_COMPAT
301 depends on COMPAT && SYSVIPC
304 config SCHED_OMIT_FRAME_POINTER
308 config ARCH_MAY_HAVE_PC_FDC
312 config PPC_UDBG_16550
315 config GENERIC_TBSYNC
317 default y if PPC32 && SMP
328 config GENERIC_BUG_RELATIVE_POINTERS
330 depends on GENERIC_BUG
332 config SYS_SUPPORTS_APM_EMULATION
333 default y if PMAC_APM_EMU
339 Used to allow a board to specify it wants an ePAPR compliant wrapper.
341 config DEFAULT_UIMAGE
344 Used to allow a board to specify it wants a uImage built by default
346 config ARCH_HIBERNATION_POSSIBLE
350 config ARCH_SUSPEND_POSSIBLE
352 depends on ADB_PMU || PPC_EFIKA || PPC_LITE5200 || PPC_83xx || \
353 (PPC_85xx && !PPC_E500MC) || PPC_86xx || PPC_PSERIES \
356 config ARCH_SUSPEND_NONZERO_CPU
358 depends on PPC_POWERNV || PPC_PSERIES
360 config PPC_DCR_NATIVE
368 depends on PPC_DCR_NATIVE || PPC_DCR_MMIO
371 config PPC_OF_PLATFORM_PCI
374 depends on PPC64 # not supported on 32 bits yet
376 config ARCH_SUPPORTS_UPROBES
379 config PPC_ADV_DEBUG_REGS
381 depends on 40x || BOOKE
384 config PPC_ADV_DEBUG_IACS
386 depends on PPC_ADV_DEBUG_REGS
390 config PPC_ADV_DEBUG_DACS
392 depends on PPC_ADV_DEBUG_REGS
395 config PPC_ADV_DEBUG_DVCS
397 depends on PPC_ADV_DEBUG_REGS
401 config PPC_ADV_DEBUG_DAC_RANGE
403 depends on PPC_ADV_DEBUG_REGS && 44x
409 config PGTABLE_LEVELS
414 source "arch/powerpc/sysdev/Kconfig"
415 source "arch/powerpc/platforms/Kconfig"
417 menu "Kernel options"
420 bool "High memory support"
424 source "kernel/Kconfig.hz"
426 config MATH_EMULATION
427 bool "Math emulation"
428 depends on 4xx || PPC_8xx || PPC_MPC832x || BOOKE || PPC_MICROWATT
431 Some PowerPC chips designed for embedded applications do not have
432 a floating-point unit and therefore do not implement the
433 floating-point instructions in the PowerPC instruction set. If you
434 say Y here, the kernel will include code to emulate a floating-point
435 unit, which will allow programs that use floating-point
438 This is also useful to emulate missing (optional) instructions
439 such as fsqrt on cores that do have an FPU but do not implement
440 them (such as Freescale BookE).
443 prompt "Math emulation options"
444 default MATH_EMULATION_FULL
445 depends on MATH_EMULATION
447 config MATH_EMULATION_FULL
448 bool "Emulate all the floating point instructions"
450 Select this option will enable the kernel to support to emulate
451 all the floating point instructions. If your SoC doesn't have
452 a FPU, you should select this.
454 config MATH_EMULATION_HW_UNIMPLEMENTED
455 bool "Just emulate the FPU unimplemented instructions"
457 Select this if you know there does have a hardware FPU on your
458 SoC, but some floating point instructions are not implemented by that.
462 config PPC_TRANSACTIONAL_MEM
463 bool "Transactional Memory support for POWERPC"
464 depends on PPC_BOOK3S_64
469 Support user-mode Transactional Memory on POWERPC.
472 bool "Ultravisor support"
473 depends on KVM_BOOK3S_HV_POSSIBLE
474 depends on DEVICE_PRIVATE
477 This option paravirtualizes the kernel to run in POWER platforms that
478 supports the Protected Execution Facility (PEF). On such platforms,
479 the ultravisor firmware runs at a privilege level above the
484 config LD_HEAD_STUB_CATCH
485 bool "Reserve 256 bytes to cope with linker stubs in HEAD text" if EXPERT
488 Very large kernels can cause linker branch stubs to be generated by
489 code in head_64.S, which moves the head text sections out of their
490 specified location. This option can work around the problem.
494 config MPROFILE_KERNEL
495 depends on PPC64 && CPU_LITTLE_ENDIAN && FUNCTION_TRACER
496 def_bool $(success,$(srctree)/arch/powerpc/tools/gcc-check-mprofile-kernel.sh $(CC) -I$(srctree)/include -D__KERNEL__)
499 bool "Support for enabling/disabling CPUs"
500 depends on SMP && (PPC_PSERIES || \
501 PPC_PMAC || PPC_POWERNV || FSL_SOC_BOOKE)
503 Say Y here to be able to disable and re-enable individual
504 CPUs at runtime on SMP machines.
506 Say N if you are unsure.
508 config PPC_QUEUED_SPINLOCKS
509 bool "Queued spinlocks" if EXPERT
511 default PPC_BOOK3S_64
513 Say Y here to use queued spinlocks which give better scalability and
514 fairness on large SMP and NUMA systems without harming single threaded
517 config ARCH_CPU_PROBE_RELEASE
519 depends on HOTPLUG_CPU
521 config PPC64_SUPPORTS_MEMORY_FAILURE
522 bool "Add support for memory hwpoison"
523 depends on PPC_BOOK3S_64
524 default "y" if PPC_POWERNV
525 select ARCH_SUPPORTS_MEMORY_FAILURE
528 bool "kexec system call"
529 depends on (PPC_BOOK3S || FSL_BOOKE || (44x && !SMP)) || PPC_BOOK3E
532 kexec is a system call that implements the ability to shutdown your
533 current kernel, and to start another kernel. It is like a reboot
534 but it is independent of the system firmware. And like a reboot
535 you can start any kernel with it, not just Linux.
537 The name comes from the similarity to the exec system call.
539 It is an ongoing process to be certain the hardware in a machine
540 is properly shutdown, so do not be surprised if this code does not
541 initially work for you. As of this writing the exact hardware
542 interface is strongly in flux, so no good recommendation can be
546 bool "kexec file based system call"
548 select HAVE_IMA_KEXEC if IMA
553 depends on CRYPTO_SHA256=y
555 This is a new version of the kexec system call. This call is
556 file based and takes in file descriptors as system call arguments
557 for kernel and initramfs as opposed to a list of segments as is the
558 case for the older kexec call.
560 config ARCH_HAS_KEXEC_PURGATORY
564 bool "Build a relocatable kernel"
565 depends on PPC64 || (FLATMEM && (44x || FSL_BOOKE))
566 select NONSTATIC_KERNEL
567 select MODULE_REL_CRCS if MODVERSIONS
569 This builds a kernel image that is capable of running at the
570 location the kernel is loaded at. For ppc32, there is no any
571 alignment restrictions, and this feature is a superset of
572 DYNAMIC_MEMSTART and hence overrides it. For ppc64, we should use
573 16k-aligned base address. The kernel is linked as a
574 position-independent executable (PIE) and contains dynamic relocations
575 which are processed early in the bootup process.
577 One use is for the kexec on panic case where the recovery kernel
578 must live at a different physical address than the primary
581 Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
582 it has been loaded at and the compile time physical addresses
583 CONFIG_PHYSICAL_START is ignored. However CONFIG_PHYSICAL_START
584 setting can still be useful to bootwrappers that need to know the
585 load address of the kernel (eg. u-boot/mkimage).
587 config RANDOMIZE_BASE
588 bool "Randomize the address of the kernel image"
589 depends on (FSL_BOOKE && FLATMEM && PPC32)
590 depends on RELOCATABLE
592 Randomizes the virtual address at which the kernel image is
593 loaded, as a security feature that deters exploit attempts
594 relying on knowledge of the location of kernel internals.
598 config RELOCATABLE_TEST
599 bool "Test relocatable kernel"
600 depends on (PPC64 && RELOCATABLE)
602 This runs the relocatable kernel at the address it was initially
603 loaded at, which tends to be non-zero and therefore test the
607 bool "Build a dump capture kernel"
608 depends on PPC64 || PPC_BOOK3S_32 || FSL_BOOKE || (44x && !SMP)
609 select RELOCATABLE if PPC64 || 44x || FSL_BOOKE
611 Build a kernel suitable for use as a dump capture kernel.
612 The same kernel binary can be used as production kernel and dump
616 bool "Firmware-assisted dump"
617 depends on PPC64 && (PPC_RTAS || PPC_POWERNV)
621 A robust mechanism to get reliable kernel crash dump with
622 assistance from firmware. This approach does not use kexec,
623 instead firmware assists in booting the capture kernel
624 while preserving memory contents. Firmware-assisted dump
625 is meant to be a kdump replacement offering robustness and
626 speed not possible without system firmware assistance.
628 If unsure, say "y". Only special kernels like petitboot may
629 need to say "N" here.
631 config PRESERVE_FA_DUMP
632 bool "Preserve Firmware-assisted dump"
633 depends on PPC64 && PPC_POWERNV && !FA_DUMP
635 On a kernel with FA_DUMP disabled, this option helps to preserve
636 crash data from a previously crash'ed kernel. Useful when the next
637 memory preserving kernel boot would process this crash data.
638 Petitboot kernel is the typical usecase for this option.
641 bool "Export OPAL memory as /sys/firmware/opal/core"
642 depends on PPC64 && PPC_POWERNV
644 This option uses the MPIPL support in firmware to provide an
645 ELF core of OPAL memory after a crash. The ELF core is exported
646 as /sys/firmware/opal/core file which is helpful in debugging
647 OPAL crashes using GDB.
650 bool "Distribute interrupts on all CPUs by default"
653 This option gives the kernel permission to distribute IRQs across
654 multiple CPUs. Saying N here will route all IRQs to the first
655 CPU. Generally saying Y is safe, although some problems have been
656 reported with SMP Power Macintoshes with this option enabled.
659 bool "NUMA Memory Allocation and Scheduler Support"
660 depends on PPC64 && SMP
661 default y if PPC_PSERIES || PPC_POWERNV
663 Enable NUMA (Non-Uniform Memory Access) support.
665 The kernel will try to allocate memory used by a CPU on the
666 local memory controller of the CPU and add some more
667 NUMA awareness to the kernel.
675 config USE_PERCPU_NUMA_NODE_ID
679 config HAVE_MEMORYLESS_NODES
683 config ARCH_SELECT_MEMORY_MODEL
687 config ARCH_FLATMEM_ENABLE
689 depends on (PPC64 && !NUMA) || PPC32
691 config ARCH_SPARSEMEM_ENABLE
694 select SPARSEMEM_VMEMMAP_ENABLE
696 config ARCH_SPARSEMEM_DEFAULT
698 depends on PPC_BOOK3S_64
700 config ILLEGAL_POINTER_VALUE
702 # This is roughly half way between the top of user space and the bottom
703 # of kernel space, which seems about as good as we can get.
704 default 0x5deadbeef0000000 if PPC64
707 config ARCH_MEMORY_PROBE
709 depends on MEMORY_HOTPLUG
715 Select the kernel logical page size. Increasing the page size
716 will reduce software overhead at each page boundary, allow
717 hardware prefetch mechanisms to be more effective, and allow
718 larger dma transfers increasing IO efficiency and reducing
719 overhead. However the utilization of memory will increase.
720 For example, each cached file will using a multiple of the
721 page size to hold its contents and the difference between the
722 end of file and the end of page is wasted.
724 Some dedicated systems, such as software raid serving with
725 accelerated calculations, have shown significant increases.
727 If you configure a 64 bit kernel for 64k pages but the
728 processor does not support them, then the kernel will simulate
729 them with 4k pages, loading them on demand, but with the
730 reduced software overhead and larger internal fragmentation.
731 For the 32 bit kernel, a large page option will not be offered
732 unless it is supported by the configured processor.
734 If unsure, choose 4K_PAGES.
738 select HAVE_ARCH_SOFT_DIRTY if PPC_BOOK3S_64
742 depends on 44x || PPC_8xx
746 depends on 44x || PPC_BOOK3S_64
747 select HAVE_ARCH_SOFT_DIRTY if PPC_BOOK3S_64
749 config PPC_256K_PAGES
750 bool "256k page size (Requires non-standard binutils settings)"
751 depends on 44x && !PPC_47x
753 Make the page size 256k.
755 The kernel will only be able to run applications that have been
756 compiled with '-zmax-page-size' set to 256K (the default is 64K) using
757 binutils later than 2.17.50.0.3, or by patching the ELF_MAXPAGESIZE
758 definition from 0x10000 to 0x40000 in older versions.
762 config PPC_PAGE_SHIFT
764 default 18 if PPC_256K_PAGES
765 default 16 if PPC_64K_PAGES
766 default 14 if PPC_16K_PAGES
770 int "Thread shift" if EXPERT
772 default "15" if PPC_256K_PAGES
773 default "14" if PPC64
774 default "14" if KASAN
777 Used to define the stack size. The default is almost always what you
778 want. Only change this if you know what you are doing.
780 config DATA_SHIFT_BOOL
781 bool "Set custom data alignment"
782 depends on ADVANCED_OPTIONS
783 depends on STRICT_KERNEL_RWX || DEBUG_PAGEALLOC || KFENCE
784 depends on PPC_BOOK3S_32 || (PPC_8xx && !PIN_TLB_DATA && !STRICT_KERNEL_RWX)
786 This option allows you to set the kernel data alignment. When
787 RAM is mapped by blocks, the alignment needs to fit the size and
788 number of possible blocks. The default should be OK for most configs.
790 Say N here unless you know what you are doing.
793 int "Data shift" if DATA_SHIFT_BOOL
794 default 24 if STRICT_KERNEL_RWX && PPC64
795 range 17 28 if (STRICT_KERNEL_RWX || DEBUG_PAGEALLOC || KFENCE) && PPC_BOOK3S_32
796 range 19 23 if (STRICT_KERNEL_RWX || DEBUG_PAGEALLOC || KFENCE) && PPC_8xx
797 default 22 if STRICT_KERNEL_RWX && PPC_BOOK3S_32
798 default 18 if (DEBUG_PAGEALLOC || KFENCE) && PPC_BOOK3S_32
799 default 23 if STRICT_KERNEL_RWX && PPC_8xx
800 default 23 if (DEBUG_PAGEALLOC || KFENCE) && PPC_8xx && PIN_TLB_DATA
801 default 19 if (DEBUG_PAGEALLOC || KFENCE) && PPC_8xx
802 default PPC_PAGE_SHIFT
804 On Book3S 32 (603+), DBATs are used to map kernel text and rodata RO.
805 Smaller is the alignment, greater is the number of necessary DBATs.
807 On 8xx, large pages (512kb or 8M) are used to map kernel linear
808 memory. Aligning to 8M reduces TLB misses as only 8M pages are used
809 in that case. If PIN_TLB is selected, it must be aligned to 8M as
810 8M pages will be pinned.
812 config FORCE_MAX_ZONEORDER
813 int "Maximum zone order"
814 range 8 9 if PPC64 && PPC_64K_PAGES
815 default "9" if PPC64 && PPC_64K_PAGES
816 range 13 13 if PPC64 && !PPC_64K_PAGES
817 default "13" if PPC64 && !PPC_64K_PAGES
818 range 9 64 if PPC32 && PPC_16K_PAGES
819 default "9" if PPC32 && PPC_16K_PAGES
820 range 7 64 if PPC32 && PPC_64K_PAGES
821 default "7" if PPC32 && PPC_64K_PAGES
822 range 5 64 if PPC32 && PPC_256K_PAGES
823 default "5" if PPC32 && PPC_256K_PAGES
827 The kernel memory allocator divides physically contiguous memory
828 blocks into "zones", where each zone is a power of two number of
829 pages. This option selects the largest power of two that the kernel
830 keeps in the memory allocator. If you need to allocate very large
831 blocks of physically contiguous memory, then you may need to
834 This config option is actually maximum order plus one. For example,
835 a value of 11 means that the largest free memory block is 2^10 pages.
837 The page size is not necessarily 4KB. For example, on 64-bit
838 systems, 64KB pages can be enabled via CONFIG_PPC_64K_PAGES. Keep
839 this in mind when choosing a value for this option.
841 config PPC_SUBPAGE_PROT
842 bool "Support setting protections for 4k subpages (subpage_prot syscall)"
844 depends on PPC_BOOK3S_64 && PPC_64K_PAGES
846 This option adds support for system call to allow user programs
847 to set access permissions (read/write, readonly, or no access)
848 on the 4k subpages of each 64k page.
850 If unsure, say N here.
852 config PPC_PROT_SAO_LPAR
853 bool "Support PROT_SAO mappings in LPARs"
854 depends on PPC_BOOK3S_64
856 This option adds support for PROT_SAO mappings from userspace
857 inside LPARs on supported CPUs.
859 This may cause issues when performing guest migration from
860 a CPU that supports SAO to one that does not.
862 If unsure, say N here.
864 config PPC_COPRO_BASE
868 bool "SMT (Hyperthreading) scheduler support"
869 depends on PPC64 && SMP
871 SMT scheduler support improves the CPU scheduler's decision making
872 when dealing with POWER5 cpus at a cost of slightly increased
873 overhead in some places. If unsure say N here.
875 config PPC_DENORMALISATION
876 bool "PowerPC denormalisation exception handling"
877 depends on PPC_BOOK3S_64
878 default "y" if PPC_POWERNV
880 Add support for handling denormalisation of single precision
881 values. Useful for bare metal only. If unsure say Y here.
884 string "Initial kernel command string"
887 On some platforms, there is currently no way for the boot loader to
888 pass arguments to the kernel. For these platforms, you can supply
889 some command-line options at build time by entering them here. In
890 most cases you will need to specify the root device here.
893 prompt "Kernel command line type" if CMDLINE != ""
894 default CMDLINE_FROM_BOOTLOADER
896 config CMDLINE_FROM_BOOTLOADER
897 bool "Use bootloader kernel arguments if available"
899 Uses the command-line options passed by the boot loader. If
900 the boot loader doesn't provide any, the default kernel command
901 string provided in CMDLINE will be used.
903 config CMDLINE_EXTEND
904 bool "Extend bootloader kernel arguments"
906 The command-line arguments provided by the boot loader will be
907 appended to the default kernel command string.
910 bool "Always use the default kernel command string"
912 Always use the default kernel command string, even if the boot
913 loader passes other arguments to the kernel.
914 This is useful if you cannot or don't want to change the
915 command-line options your boot loader passes to the kernel.
920 string "Additional default image types"
922 List additional targets to be built by the bootwrapper here (separated
923 by spaces). This is useful for targets that depend of device tree
924 files in the .dts directory.
926 Targets in this list will be build as part of the default build
927 target, or when the user does a 'make zImage' or a
928 'make zImage.initrd'.
930 If unsure, leave blank
932 config ARCH_WANTS_FREEZER_CONTROL
936 source "kernel/power/Kconfig"
939 prompt "PowerPC Memory Protection Keys"
941 depends on PPC_BOOK3S_64
942 select ARCH_USES_HIGH_VMA_FLAGS
943 select ARCH_HAS_PKEYS
945 Memory Protection Keys provides a mechanism for enforcing
946 page-based protections, but without requiring modification of the
947 page tables when an application changes protection domains.
949 For details, see Documentation/core-api/protection-keys.rst
953 config PPC_SECURE_BOOT
954 prompt "Enable secure boot support"
956 depends on PPC_POWERNV || PPC_PSERIES
957 depends on IMA_ARCH_POLICY
958 imply IMA_SECURE_AND_OR_TRUSTED_BOOT
960 Systems with firmware secure boot enabled need to define security
961 policies to extend secure boot to the OS. This config allows a user
962 to enable OS secure boot on systems that have firmware support for
963 it. If in doubt say N.
965 config PPC_SECVAR_SYSFS
966 bool "Enable sysfs interface for POWER secure variables"
968 depends on PPC_SECURE_BOOT
971 POWER secure variables are managed and controlled by firmware.
972 These variables are exposed to userspace via sysfs to enable
973 read/write operations on these variables. Say Y if you have
974 secure boot enabled and want to expose variables to userspace.
976 config PPC_RTAS_FILTER
977 bool "Enable filtering of RTAS syscalls"
981 The RTAS syscall API has security issues that could be used to
982 compromise system integrity. This option enforces restrictions on the
983 RTAS calls and arguments passed by userspace programs to mitigate
986 Say Y unless you know what you are doing and the filter is causing
998 bool "Support for ISA-bus hardware"
1002 Find out whether you have ISA slots on your motherboard. ISA is the
1003 name of a bus system, i.e. the way the CPU talks to the other stuff
1004 inside your box. If you have an Apple machine, say N here; if you
1005 have an IBM RS/6000 or pSeries machine, say Y. If you have an
1006 embedded board, consult your board documentation.
1008 config GENERIC_ISA_DMA
1010 depends on ISA_DMA_API
1013 config PPC_INDIRECT_PCI
1016 default y if 40x || 44x
1026 select ARCH_HAS_DMA_SET_MASK
1027 select PPC_INDIRECT_PCI
1033 depends on SUSPEND && (PPC_85xx || PPC_86xx)
1035 Freescale MPC85xx/MPC86xx power management controller support
1036 (suspend/resume). For MPC83xx see platforms/83xx/suspend.c
1041 depends on SUSPEND && (44x || 40x)
1043 PPC4xx Clock Power Management (CPM) support (suspend/resume).
1044 It also enables support for two different idle states (idle-wait
1051 bool "Freescale Local Bus support"
1053 Enables reporting of errors from the Freescale local bus
1054 controller. Also contains some common code used by
1055 drivers for specific local bus peripherals.
1059 depends on PPC_83xx || QUICC_ENGINE || CPM2
1061 Freescale General-purpose Timers support
1065 depends on PCI && 8260
1066 select PPC_INDIRECT_PCI
1070 bool "Freescale Embedded SRIO Controller support"
1071 depends on RAPIDIO = y && HAVE_RAPIDIO
1074 Include support for RapidIO controller on Freescale embedded
1075 processors (MPC8548, MPC8641, etc).
1079 config NONSTATIC_KERNEL
1082 menu "Advanced setup"
1085 config ADVANCED_OPTIONS
1086 bool "Prompt for advanced kernel configuration options"
1088 This option will enable prompting for a variety of advanced kernel
1089 configuration options. These options can cause the kernel to not
1090 work if they are set incorrectly, but can be used to optimize certain
1091 aspects of kernel memory management.
1093 Unless you know what you are doing, say N here.
1095 comment "Default settings for advanced configuration options are used"
1096 depends on !ADVANCED_OPTIONS
1098 config LOWMEM_SIZE_BOOL
1099 bool "Set maximum low memory"
1100 depends on ADVANCED_OPTIONS
1102 This option allows you to set the maximum amount of memory which
1103 will be used as "low memory", that is, memory which the kernel can
1104 access directly, without having to set up a kernel virtual mapping.
1105 This can be useful in optimizing the layout of kernel virtual
1108 Say N here unless you know what you are doing.
1111 hex "Maximum low memory size (in bytes)" if LOWMEM_SIZE_BOOL
1112 default "0x30000000"
1114 config LOWMEM_CAM_NUM_BOOL
1115 bool "Set number of CAMs to use to map low memory"
1116 depends on ADVANCED_OPTIONS && FSL_BOOKE
1118 This option allows you to set the maximum number of CAM slots that
1119 will be used to map low memory. There are a limited number of slots
1120 available and even more limited number that will fit in the L1 MMU.
1121 However, using more entries will allow mapping more low memory. This
1122 can be useful in optimizing the layout of kernel virtual memory.
1124 Say N here unless you know what you are doing.
1126 config LOWMEM_CAM_NUM
1127 depends on FSL_BOOKE
1128 int "Number of CAMs to use to map low memory" if LOWMEM_CAM_NUM_BOOL
1131 config DYNAMIC_MEMSTART
1132 bool "Enable page aligned dynamic load address for kernel"
1133 depends on ADVANCED_OPTIONS && FLATMEM && (FSL_BOOKE || 44x)
1134 select NONSTATIC_KERNEL
1136 This option enables the kernel to be loaded at any page aligned
1137 physical address. The kernel creates a mapping from KERNELBASE to
1138 the address where the kernel is loaded. The page size here implies
1139 the TLB page size of the mapping for kernel on the particular platform.
1140 Please refer to the init code for finding the TLB page size.
1142 DYNAMIC_MEMSTART is an easy way of implementing pseudo-RELOCATABLE
1143 kernel image, where the only restriction is the page aligned kernel
1144 load address. When this option is enabled, the compile time physical
1145 address CONFIG_PHYSICAL_START is ignored.
1147 This option is overridden by CONFIG_RELOCATABLE
1149 config PAGE_OFFSET_BOOL
1150 bool "Set custom page offset address"
1151 depends on ADVANCED_OPTIONS
1153 This option allows you to set the kernel virtual address at which
1154 the kernel will map low memory. This can be useful in optimizing
1155 the virtual memory layout of the system.
1157 Say N here unless you know what you are doing.
1160 hex "Virtual address of memory base" if PAGE_OFFSET_BOOL
1161 default "0xc0000000"
1163 config KERNEL_START_BOOL
1164 bool "Set custom kernel base address"
1165 depends on ADVANCED_OPTIONS
1167 This option allows you to set the kernel virtual address at which
1168 the kernel will be loaded. Normally this should match PAGE_OFFSET
1169 however there are times (like kdump) that one might not want them
1172 Say N here unless you know what you are doing.
1175 hex "Virtual address of kernel base" if KERNEL_START_BOOL
1176 default PAGE_OFFSET if PAGE_OFFSET_BOOL
1177 default "0xc2000000" if CRASH_DUMP && !NONSTATIC_KERNEL
1178 default "0xc0000000"
1180 config PHYSICAL_START_BOOL
1181 bool "Set physical address where the kernel is loaded"
1182 depends on ADVANCED_OPTIONS && FLATMEM && FSL_BOOKE
1184 This gives the physical address where the kernel is loaded.
1186 Say N here unless you know what you are doing.
1188 config PHYSICAL_START
1189 hex "Physical address where the kernel is loaded" if PHYSICAL_START_BOOL
1190 default "0x02000000" if PPC_BOOK3S && CRASH_DUMP && !NONSTATIC_KERNEL
1191 default "0x00000000"
1193 config PHYSICAL_ALIGN
1195 default "0x04000000" if FSL_BOOKE
1197 This value puts the alignment restrictions on physical address
1198 where kernel is loaded and run from. Kernel is compiled for an
1199 address which meets above alignment restriction.
1201 config TASK_SIZE_BOOL
1202 bool "Set custom user task size"
1203 depends on ADVANCED_OPTIONS
1205 This option allows you to set the amount of virtual address space
1206 allocated to user tasks. This can be useful in optimizing the
1207 virtual memory layout of the system.
1209 Say N here unless you know what you are doing.
1212 hex "Size of user task space" if TASK_SIZE_BOOL
1213 default "0x80000000" if PPC_8xx
1214 default "0xb0000000" if PPC_BOOK3S_32
1215 default "0xc0000000"
1219 # This value must have zeroes in the bottom 60 bits otherwise lots will break
1222 default "0xc000000000000000"
1225 default "0xc000000000000000"
1226 config PHYSICAL_START
1228 default "0x00000000"
1234 config PPC_LIB_RHEAP
1237 source "arch/powerpc/kvm/Kconfig"
1239 source "kernel/livepatch/Kconfig"