arch/arm64/boot/dts/marvell/cn9131-db.dts

   1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
   2 /*
   3  * Copyright (C) 2019 Marvell International Ltd.
   4  *
   5  * Device tree for the CN9131-DB board.
   6  */
   7
   8 #include "cn9130-db.dts"
   9
  10 / {
  11         model = "Marvell Armada CN9131-DB";
  12         compatible = "marvell,cn9131", "marvell,cn9130",
  13                      "marvell,armada-ap807-quad", "marvell,armada-ap807";
  14
  15         aliases {
  16                 gpio3 = &cp1_gpio1;
  17                 gpio4 = &cp1_gpio2;
  18                 ethernet3 = &cp1_eth0;
  19                 ethernet4 = &cp1_eth1;
  20         };
  21
  22         cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 {
  23                 compatible = "regulator-fixed";
  24                 pinctrl-names = "default";
  25                 pinctrl-0 = <&cp1_xhci0_vbus_pins>;
  26                 regulator-name = "cp1-xhci0-vbus";
  27                 regulator-min-microvolt = <5000000>;
  28                 regulator-max-microvolt = <5000000>;
  29                 enable-active-high;
  30                 gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>;
  31         };
  32
  33         cp1_usb3_0_phy0: cp1_usb3_phy0 {
  34                 compatible = "usb-nop-xceiv";
  35                 vcc-supply = <&cp1_reg_usb3_vbus0>;
  36         };
  37
  38         cp1_sfp_eth1: sfp-eth1 {
  39                 compatible = "sff,sfp";
  40                 i2c-bus = <&cp1_i2c0>;
  41                 los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
  42                 mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
  43                 tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>;
  44                 tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
  45                 pinctrl-names = "default";
  46                 pinctrl-0 = <&cp1_sfp_pins>;
  47                 /*
  48                  * SFP cages are unconnected on early PCBs because of an the I2C
  49                  * lanes not being connected. Prevent the port for being
  50                  * unusable by disabling the SFP node.
  51                  */
  52                 status = "disabled";
  53         };
  54 };
  55
  56 /*
  57  * Instantiate the first slave CP115
  58  */
  59
  60 #define CP11X_NAME              cp1
  61 #define CP11X_BASE              f4000000
  62 #define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
  63 #define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
  64 #define CP11X_PCIE0_BASE        f4600000
  65 #define CP11X_PCIE1_BASE        f4620000
  66 #define CP11X_PCIE2_BASE        f4640000
  67
  68 #include "armada-cp115.dtsi"
  69
  70 #undef CP11X_NAME
  71 #undef CP11X_BASE
  72 #undef CP11X_PCIEx_MEM_BASE
  73 #undef CP11X_PCIEx_MEM_SIZE
  74 #undef CP11X_PCIE0_BASE
  75 #undef CP11X_PCIE1_BASE
  76 #undef CP11X_PCIE2_BASE
  77
  78 &cp1_crypto {
  79         status = "disabled";
  80 };
  81
  82 &cp1_ethernet {
  83         status = "okay";
  84 };
  85
  86 /* CON50 */
  87 &cp1_eth0 {
  88         status = "disabled";
  89         phy-mode = "10gbase-kr";
  90         /* Generic PHY, providing serdes lanes */
  91         phys = <&cp1_comphy4 0>;
  92         managed = "in-band-status";
  93         sfp = <&cp1_sfp_eth1>;
  94 };
  95
  96 &cp1_gpio1 {
  97         status = "okay";
  98 };
  99
 100 &cp1_gpio2 {
 101         status = "okay";
 102 };
 103
 104 &cp1_i2c0 {
 105         status = "okay";
 106         pinctrl-names = "default";
 107         pinctrl-0 = <&cp1_i2c0_pins>;
 108         clock-frequency = <100000>;
 109 };
 110
 111 /* CON40 */
 112 &cp1_pcie0 {
 113         pinctrl-names = "default";
 114         pinctrl-0 = <&cp1_pcie_reset_pins>;
 115         num-lanes = <2>;
 116         num-viewport = <8>;
 117         marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>;
 118         status = "okay";
 119         /* Generic PHY, providing serdes lanes */
 120         phys = <&cp1_comphy0 0
 121                 &cp1_comphy1 0>;
 122 };
 123
 124 &cp1_sata0 {
 125         status = "okay";
 126
 127         /* CON32 */
 128         sata-port@1 {
 129                 /* Generic PHY, providing serdes lanes */
 130                 phys = <&cp1_comphy5 1>;
 131         };
 132 };
 133
 134 /* U24 */
 135 &cp1_spi1 {
 136         status = "okay";
 137         pinctrl-names = "default";
 138         pinctrl-0 = <&cp1_spi0_pins>;
 139         reg = <0x700680 0x50>;
 140
 141         spi-flash@0 {
 142                 #address-cells = <0x1>;
 143                 #size-cells = <0x1>;
 144                 compatible = "jedec,spi-nor";
 145                 reg = <0x0>;
 146                 /* On-board MUX does not allow higher frequencies */
 147                 spi-max-frequency = <40000000>;
 148
 149                 partitions {
 150                         compatible = "fixed-partitions";
 151                         #address-cells = <1>;
 152                         #size-cells = <1>;
 153
 154                         partition@0 {
 155                                 label = "U-Boot-1";
 156                                 reg = <0x0 0x200000>;
 157                         };
 158
 159                         partition@400000 {
 160                                 label = "Filesystem-1";
 161                                 reg = <0x200000 0xe00000>;
 162                         };
 163                 };
 164         };
 165
 166 };
 167
 168 &cp1_syscon0 {
 169         cp1_pinctrl: pinctrl {
 170                 compatible = "marvell,cp115-standalone-pinctrl";
 171
 172                 cp1_i2c0_pins: cp1-i2c-pins-0 {
 173                         marvell,pins = "mpp37", "mpp38";
 174                         marvell,function = "i2c0";
 175                 };
 176                 cp1_spi0_pins: cp1-spi-pins-0 {
 177                         marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
 178                         marvell,function = "spi1";
 179                 };
 180                 cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
 181                         marvell,pins = "mpp3";
 182                         marvell,function = "gpio";
 183                 };
 184                 cp1_sfp_pins: sfp-pins {
 185                         marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11";
 186                         marvell,function = "gpio";
 187                 };
 188                 cp1_pcie_reset_pins: cp1-pcie-reset-pins {
 189                         marvell,pins = "mpp0";
 190                         marvell,function = "gpio";
 191                 };
 192         };
 193 };
 194
 195 /* CON58 */
 196 &cp1_utmi {
 197         status = "okay";
 198 };
 199
 200 &cp1_usb3_1 {
 201         status = "okay";
 202         usb-phy = <&cp1_usb3_0_phy0>;
 203         /* Generic PHY, providing serdes lanes */
 204         phys = <&cp1_comphy3 1>, <&cp1_utmi1>;
 205         phy-names = "usb", "utmi";
 206         dr_mode = "host";
 207 };