1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 $id: http://devicetree.org/schemas/thermal/qcom-spmi-adc-tm5.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Qualcomm's SPMI PMIC ADC Thermal Monitoring
9 - Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
13 const: qcom,spmi-adc-tm5
21 "#thermal-sensor-cells":
24 Number of cells required to uniquely identify the thermal sensors. Since
25 we have multiple sensors this is set to 1
34 $ref: /schemas/types.yaml#/definitions/uint32
35 description: Number of samples to be used for measurement.
45 $ref: /schemas/types.yaml#/definitions/uint32
46 description: This parameter is used to decrease ADC sampling rate.
47 Quicker measurements can be made by reducing decimation ratio.
55 "^([-a-z0-9]*)@[0-7]$":
58 Represent one thermal sensor.
62 $ref: /schemas/types.yaml#/definitions/uint32
63 description: Specify the sensor channel. There are 8 channels in PMIC5's ADC TM
69 From common IIO binding. Used to pipe PMIC ADC channel to thermal monitor
72 $ref: /schemas/types.yaml#/definitions/flag
74 Channel calibration type.
75 If this property is specified VADC will use the VDD reference
76 (1.875V) and GND for channel calibration. If property is not found,
77 channel will be calibrated with 0V and 1.25V reference channels,
78 also known as absolute calibration.
80 qcom,hw-settle-time-us:
81 $ref: /schemas/types.yaml#/definitions/uint32
82 description: Time between AMUX getting configured and the ADC starting conversion.
83 enum: [15, 100, 200, 300, 400, 500, 600, 700, 1000, 2000, 4000, 8000, 16000, 32000, 64000, 128000]
86 $ref: /schemas/types.yaml#/definitions/uint32-array
87 description: Used for scaling the channel input signal before the
88 signal is fed to VADC. The configuration for this node is to know the
89 pre-determined ratio and use it for post scaling. It is a pair of
90 integers, denoting the numerator and denominator of the fraction by
91 which input signal is multiplied. For example, <1 3> indicates the
92 signal is scaled down to 1/3 of its value before ADC measurement. If
93 property is not found default value depending on chip will be used.
96 - enum: [ 1, 3, 4, 6, 20, 8, 10 ]
102 additionalProperties:
111 - "#thermal-sensor-cells"
113 additionalProperties: false
117 #include <dt-bindings/iio/qcom,spmi-vadc.h>
118 #include <dt-bindings/interrupt-controller/irq.h>
120 #address-cells = <1>;
122 pm8150b_adc: adc@3100 {
124 compatible = "qcom,spmi-adc5";
125 #address-cells = <1>;
127 #io-channel-cells = <1>;
129 /* Other propreties are omitted */
131 reg = <ADC5_AMUX_THM3_100K_PU>;
133 qcom,hw-settle-time = <200>;
137 pm8150b_adc_tm: adc-tm@3500 {
138 compatible = "qcom,spmi-adc-tm5";
140 interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
141 #thermal-sensor-cells = <1>;
142 #address-cells = <1>;
147 io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>;
149 qcom,hw-settle-time-us = <200>;