arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source
   4  *
   5  * Copyright (c) 2020, The Linux Foundation. All rights reserved.
   6  */
   7
   8 /dts-v1/;
   9
  10 #include <dt-bindings/input/linux-event-codes.h>
  11 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
  12 #include <dt-bindings/sound/qcom,q6afe.h>
  13 #include <dt-bindings/sound/qcom,q6asm.h>
  14
  15 #include "sdm845.dtsi"
  16 #include "sdm845-wcd9340.dtsi"
  17 #include "pm8998.dtsi"
  18 #include "pmi8998.dtsi"
  19
  20 /delete-node/ &rmtfs_mem;
  21
  22 / {
  23         aliases {
  24                 serial0 = &uart9;
  25                 serial1 = &uart6;
  26         };
  27
  28         chosen {
  29                 stdout-path = "serial0:115200n8";
  30         };
  31
  32         gpio-hall-sensor {
  33                 compatible = "gpio-keys";
  34                 label = "Hall effect sensor";
  35
  36                 pinctrl-0 = <&hall_sensor_default>;
  37                 pinctrl-names = "default";
  38
  39                 event-hall-sensor {
  40                         gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
  41                         label = "Hall Effect Sensor";
  42                         linux,input-type = <EV_SW>;
  43                         linux,code = <SW_LID>;
  44                         linux,can-disable;
  45                         wakeup-source;
  46                 };
  47         };
  48
  49         gpio-keys {
  50                 compatible = "gpio-keys";
  51                 label = "Volume keys";
  52                 autorepeat;
  53
  54                 pinctrl-names = "default";
  55                 pinctrl-0 = <&volume_down_gpio &volume_up_gpio>;
  56
  57                 key-vol-down {
  58                         label = "Volume down";
  59                         linux,code = <KEY_VOLUMEDOWN>;
  60                         gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>;
  61                         debounce-interval = <15>;
  62                 };
  63
  64                 key-vol-up {
  65                         label = "Volume up";
  66                         linux,code = <KEY_VOLUMEUP>;
  67                         gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
  68                         debounce-interval = <15>;
  69                 };
  70         };
  71
  72         reserved-memory {
  73                 /*
  74                  * The rmtfs_mem needs to be guarded due to "XPU limitations"
  75                  * it is otherwise possible for an allocation adjacent to the
  76                  * rmtfs_mem region to trigger an XPU violation, causing a crash.
  77                  */
  78                 rmtfs_lower_guard: rmtfs-lower-guard@f5b00000 {
  79                         no-map;
  80                         reg = <0 0xf5b00000 0 0x1000>;
  81                 };
  82                 /*
  83                  * The rmtfs memory region in downstream is 'dynamically allocated'
  84                  * but given the same address every time. Hard code it as this address is
  85                  * where the modem firmware expects it to be.
  86                  */
  87                 rmtfs_mem: rmtfs-mem@f5b01000 {
  88                         compatible = "qcom,rmtfs-mem";
  89                         reg = <0 0xf5b01000 0 0x200000>;
  90                         no-map;
  91
  92                         qcom,client-id = <1>;
  93                         qcom,vmid = <15>;
  94                 };
  95                 rmtfs_upper_guard: rmtfs-upper-guard@f5d01000 {
  96                         no-map;
  97                         reg = <0 0xf5d01000 0 0x1000>;
  98                 };
  99
 100                 /*
 101                  * It seems like reserving the old rmtfs_mem region is also needed to prevent
 102                  * random crashes which are most likely modem related, more testing needed.
 103                  */
 104                 removed_region: removed-region@88f00000 {
 105                         no-map;
 106                         reg = <0 0x88f00000 0 0x1c00000>;
 107                 };
 108
 109                 ramoops: ramoops@ac300000 {
 110                         compatible = "ramoops";
 111                         reg = <0 0xac300000 0 0x400000>;
 112                         record-size = <0x40000>;
 113                         console-size = <0x40000>;
 114                         ftrace-size = <0x40000>;
 115                         pmsg-size = <0x200000>;
 116                         ecc-size = <16>;
 117                 };
 118         };
 119
 120         vph_pwr: vph-pwr-regulator {
 121                 compatible = "regulator-fixed";
 122                 regulator-name = "vph_pwr";
 123                 regulator-min-microvolt = <3700000>;
 124                 regulator-max-microvolt = <3700000>;
 125         };
 126
 127         /*
 128          * Apparently RPMh does not provide support for PM8998 S4 because it
 129          * is always-on; model it as a fixed regulator.
 130          */
 131         vreg_s4a_1p8: pm8998-smps4 {
 132                 compatible = "regulator-fixed";
 133                 regulator-name = "vreg_s4a_1p8";
 134
 135                 regulator-min-microvolt = <1800000>;
 136                 regulator-max-microvolt = <1800000>;
 137
 138                 regulator-always-on;
 139                 regulator-boot-on;
 140
 141                 vin-supply = <&vph_pwr>;
 142         };
 143
 144         /*
 145          * The touchscreen regulator seems to be controlled somehow by a gpio.
 146          * Model it as a fixed regulator and keep it on. Without schematics we
 147          * don't know how this is actually wired up...
 148          */
 149         ts_1p8_supply: ts-1p8-regulator {
 150                 compatible = "regulator-fixed";
 151                 regulator-name = "ts_1p8_supply";
 152
 153                 regulator-min-microvolt = <1800000>;
 154                 regulator-max-microvolt = <1800000>;
 155
 156                 gpio = <&tlmm 88 0>;
 157                 enable-active-high;
 158                 regulator-boot-on;
 159         };
 160 };
 161
 162 &adsp_pas {
 163         status = "okay";
 164         firmware-name = "qcom/sdm845/oneplus6/adsp.mbn";
 165 };
 166
 167 &apps_rsc {
 168         regulators-0 {
 169                 compatible = "qcom,pm8998-rpmh-regulators";
 170                 qcom,pmic-id = "a";
 171
 172                 vdd-s1-supply = <&vph_pwr>;
 173                 vdd-s2-supply = <&vph_pwr>;
 174                 vdd-s3-supply = <&vph_pwr>;
 175                 vdd-s4-supply = <&vph_pwr>;
 176                 vdd-s5-supply = <&vph_pwr>;
 177                 vdd-s6-supply = <&vph_pwr>;
 178                 vdd-s7-supply = <&vph_pwr>;
 179                 vdd-s8-supply = <&vph_pwr>;
 180                 vdd-s9-supply = <&vph_pwr>;
 181                 vdd-s10-supply = <&vph_pwr>;
 182                 vdd-s11-supply = <&vph_pwr>;
 183                 vdd-s12-supply = <&vph_pwr>;
 184                 vdd-s13-supply = <&vph_pwr>;
 185                 vdd-l1-l27-supply = <&vreg_s7a_1p025>;
 186                 vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
 187                 vdd-l3-l11-supply = <&vreg_s7a_1p025>;
 188                 vdd-l4-l5-supply = <&vreg_s7a_1p025>;
 189                 vdd-l6-supply = <&vph_pwr>;
 190                 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
 191                 vdd-l9-supply = <&vreg_bob>;
 192                 vdd-l10-l23-l25-supply = <&vreg_bob>;
 193                 vdd-l13-l19-l21-supply = <&vreg_bob>;
 194                 vdd-l16-l28-supply = <&vreg_bob>;
 195                 vdd-l18-l22-supply = <&vreg_bob>;
 196                 vdd-l20-l24-supply = <&vreg_bob>;
 197                 vdd-l26-supply = <&vreg_s3a_1p35>;
 198                 vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
 199
 200                 vreg_s3a_1p35: smps3 {
 201                         regulator-min-microvolt = <1352000>;
 202                         regulator-max-microvolt = <1352000>;
 203                 };
 204
 205                 vreg_s5a_2p04: smps5 {
 206                         regulator-min-microvolt = <1904000>;
 207                         regulator-max-microvolt = <2040000>;
 208                 };
 209
 210                 vreg_s7a_1p025: smps7 {
 211                         regulator-min-microvolt = <900000>;
 212                         regulator-max-microvolt = <1028000>;
 213                 };
 214
 215                 vdda_mipi_dsi0_pll:
 216                 vdda_qlink_lv:
 217                 vdda_ufs1_core:
 218                 vdda_usb1_ss_core:
 219                 vreg_l1a_0p875: ldo1 {
 220                         regulator-min-microvolt = <880000>;
 221                         regulator-max-microvolt = <880000>;
 222                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 223                 };
 224
 225                 vreg_l2a_1p2: ldo2 {
 226                         regulator-min-microvolt = <1200000>;
 227                         regulator-max-microvolt = <1200000>;
 228                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 229                         regulator-always-on;
 230                 };
 231
 232                 vreg_l5a_0p8: ldo5 {
 233                         regulator-min-microvolt = <800000>;
 234                         regulator-max-microvolt = <800000>;
 235                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 236                 };
 237
 238                 vreg_l7a_1p8: ldo7 {
 239                         regulator-min-microvolt = <1800000>;
 240                         regulator-max-microvolt = <1800000>;
 241                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 242                 };
 243
 244                 vdda_qusb_hs0_1p8:
 245                 vreg_l12a_1p8: ldo12 {
 246                         regulator-min-microvolt = <1800000>;
 247                         regulator-max-microvolt = <1800000>;
 248                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 249                 };
 250
 251                 vreg_l14a_1p88: ldo14 {
 252                         regulator-min-microvolt = <1800000>;
 253                         regulator-max-microvolt = <1800000>;
 254                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 255                         regulator-always-on;
 256                 };
 257
 258                 vreg_l17a_1p3: ldo17 {
 259                         regulator-min-microvolt = <1304000>;
 260                         regulator-max-microvolt = <1304000>;
 261                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 262                 };
 263
 264                 vreg_l20a_2p95: ldo20 {
 265                         regulator-min-microvolt = <2704000>;
 266                         regulator-max-microvolt = <2960000>;
 267                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 268                 };
 269
 270                 vreg_l23a_3p3: ldo23 {
 271                         regulator-min-microvolt = <3300000>;
 272                         regulator-max-microvolt = <3312000>;
 273                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 274                 };
 275
 276                 vdda_qusb_hs0_3p1:
 277                 vreg_l24a_3p075: ldo24 {
 278                         regulator-min-microvolt = <3088000>;
 279                         regulator-max-microvolt = <3088000>;
 280                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 281                 };
 282
 283                 vreg_l25a_3p3: ldo25 {
 284                         regulator-min-microvolt = <3300000>;
 285                         regulator-max-microvolt = <3312000>;
 286                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 287                 };
 288
 289                 vdda_mipi_dsi0_1p2:
 290                 vdda_ufs1_1p2:
 291                 vreg_l26a_1p2: ldo26 {
 292                         regulator-min-microvolt = <1200000>;
 293                         regulator-max-microvolt = <1200000>;
 294                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 295                 };
 296
 297                 vreg_l28a_3p0: ldo28 {
 298                         regulator-min-microvolt = <2856000>;
 299                         regulator-max-microvolt = <3008000>;
 300                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 301                 };
 302         };
 303
 304         regulators-1 {
 305                 compatible = "qcom,pmi8998-rpmh-regulators";
 306                 qcom,pmic-id = "b";
 307
 308                 vdd-bob-supply = <&vph_pwr>;
 309
 310                 vreg_bob: bob {
 311                         regulator-min-microvolt = <3312000>;
 312                         regulator-max-microvolt = <3600000>;
 313                         regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
 314                         regulator-allow-bypass;
 315                 };
 316         };
 317
 318         regulators-2 {
 319                 compatible = "qcom,pm8005-rpmh-regulators";
 320                 qcom,pmic-id = "c";
 321
 322                 vdd-s1-supply = <&vph_pwr>;
 323                 vdd-s2-supply = <&vph_pwr>;
 324                 vdd-s3-supply = <&vph_pwr>;
 325                 vdd-s4-supply = <&vph_pwr>;
 326
 327                 vreg_s3c_0p6: smps3 {
 328                         regulator-min-microvolt = <600000>;
 329                         regulator-max-microvolt = <600000>;
 330                 };
 331         };
 332 };
 333
 334 &cdsp_pas {
 335         status = "okay";
 336         firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn";
 337 };
 338
 339 &gcc {
 340         protected-clocks = <GCC_QSPI_CORE_CLK>,
 341                                 <GCC_QSPI_CORE_CLK_SRC>,
 342                                 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
 343                                 <GCC_LPASS_Q6_AXI_CLK>,
 344                                 <GCC_LPASS_SWAY_CLK>;
 345 };
 346
 347 &gmu {
 348         status = "okay";
 349 };
 350
 351 &gpu {
 352         status = "okay";
 353
 354         zap-shader {
 355                 memory-region = <&gpu_mem>;
 356                 firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn";
 357         };
 358 };
 359
 360 &i2c10 {
 361         status = "okay";
 362         clock-frequency = <100000>;
 363
 364         bq27441_fg: bq27441-battery@55 {
 365                 compatible = "ti,bq27411";
 366                 status = "okay";
 367                 reg = <0x55>;
 368         };
 369 };
 370
 371 &i2c12 {
 372         status = "okay";
 373         clock-frequency = <400000>;
 374
 375         synaptics-rmi4-i2c@20 {
 376                 compatible = "syna,rmi4-i2c";
 377                 reg = <0x20>;
 378                 #address-cells = <1>;
 379                 #size-cells = <0>;
 380                 interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
 381
 382                 pinctrl-names = "default";
 383                 pinctrl-0 = <&ts_default_pins>;
 384
 385                 vdd-supply = <&vreg_l28a_3p0>;
 386                 vio-supply = <&ts_1p8_supply>;
 387
 388                 syna,reset-delay-ms = <200>;
 389                 syna,startup-delay-ms = <200>;
 390
 391                 rmi4-f01@1 {
 392                         reg = <0x01>;
 393                         syna,nosleep-mode = <1>;
 394                 };
 395
 396                 rmi4_f12: rmi4-f12@12 {
 397                         reg = <0x12>;
 398                         touchscreen-x-mm = <68>;
 399                         touchscreen-y-mm = <144>;
 400                         syna,sensor-type = <1>;
 401                         syna,rezero-wait-ms = <200>;
 402                 };
 403         };
 404 };
 405
 406 &ipa {
 407         qcom,gsi-loader = "self";
 408         memory-region = <&ipa_fw_mem>;
 409         firmware-name = "qcom/sdm845/oneplus6/ipa_fws.mbn";
 410         status = "okay";
 411 };
 412
 413 &mdss {
 414         status = "okay";
 415 };
 416
 417 &mdss_dsi0 {
 418         status = "okay";
 419         vdda-supply = <&vdda_mipi_dsi0_1p2>;
 420
 421         /*
 422          * Both devices use different panels but all other properties
 423          * are common. Compatible line is declared in device dts.
 424          */
 425         display_panel: panel@0 {
 426                 status = "disabled";
 427
 428                 reg = <0>;
 429
 430                 vddio-supply = <&vreg_l14a_1p88>;
 431
 432                 reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
 433
 434                 pinctrl-names = "default";
 435                 pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>;
 436
 437                 port {
 438                         panel_in: endpoint {
 439                                 remote-endpoint = <&mdss_dsi0_out>;
 440                         };
 441                 };
 442         };
 443 };
 444
 445 &mdss_dsi0_out {
 446         remote-endpoint = <&panel_in>;
 447         data-lanes = <0 1 2 3>;
 448 };
 449
 450 &mdss_dsi0_phy {
 451         status = "okay";
 452         vdds-supply = <&vdda_mipi_dsi0_pll>;
 453 };
 454
 455 /* Modem/wifi */
 456 &mss_pil {
 457         status = "okay";
 458         firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn";
 459 };
 460
 461 &pm8998_gpios {
 462         volume_down_gpio: pm8998-gpio5-state {
 463                 pinconf {
 464                         pins = "gpio5";
 465                         function = "normal";
 466                         input-enable;
 467                         bias-pull-up;
 468                         qcom,drive-strength = <0>;
 469                 };
 470         };
 471
 472         volume_up_gpio: pm8998-gpio6-state {
 473                 pinconf {
 474                         pins = "gpio6";
 475                         function = "normal";
 476                         input-enable;
 477                         bias-pull-up;
 478                         qcom,drive-strength = <0>;
 479                 };
 480         };
 481 };
 482
 483 &pmi8998_charger {
 484         status = "okay";
 485 };
 486
 487 &q6afedai {
 488         qi2s@22 {
 489                 reg = <22>;
 490                 qcom,sd-lines = <1>;
 491         };
 492
 493         qi2s@23 {
 494                 reg = <23>;
 495                 qcom,sd-lines = <0>;
 496         };
 497 };
 498
 499 &q6asmdai {
 500         dai@0 {
 501                 reg = <0>;
 502         };
 503
 504         dai@1 {
 505                 reg = <1>;
 506         };
 507
 508         dai@2 {
 509                 reg = <2>;
 510         };
 511
 512         dai@3 {
 513                 reg = <3>;
 514         };
 515
 516         dai@4 {
 517                 reg = <4>;
 518         };
 519
 520         dai@5 {
 521                 reg = <5>;
 522         };
 523 };
 524
 525 &qupv3_id_1 {
 526         status = "okay";
 527 };
 528
 529 &qupv3_id_0 {
 530         status = "okay";
 531 };
 532
 533 &qup_i2c10_default {
 534         drive-strength = <2>;
 535         bias-disable;
 536 };
 537
 538 &qup_i2c12_default {
 539         drive-strength = <2>;
 540         bias-disable;
 541 };
 542
 543 &qup_uart9_rx {
 544         drive-strength = <2>;
 545         bias-pull-up;
 546 };
 547
 548 &qup_uart9_tx {
 549         drive-strength = <2>;
 550         bias-disable;
 551 };
 552
 553 &slpi_pas {
 554         firmware-name = "qcom/sdm845/oneplus6/slpi.mbn";
 555         status = "okay";
 556 };
 557
 558 &sound {
 559         compatible = "qcom,sdm845-sndcard";
 560         pinctrl-0 = <&quat_mi2s_active &quat_mi2s_sd0_active &quat_mi2s_sd1_active>;
 561         pinctrl-names = "default";
 562         status = "okay";
 563
 564         mm1-dai-link {
 565                 link-name = "MultiMedia1";
 566                 cpu {
 567                         sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
 568                 };
 569         };
 570
 571         mm2-dai-link {
 572                 link-name = "MultiMedia2";
 573                 cpu {
 574                         sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
 575                 };
 576         };
 577
 578         mm3-dai-link {
 579                 link-name = "MultiMedia3";
 580                 cpu {
 581                         sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
 582                 };
 583         };
 584
 585         mm4-dai-link {
 586                 link-name = "MultiMedia4";
 587                 cpu {
 588                         sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA4>;
 589                 };
 590         };
 591
 592         mm5-dai-link {
 593                 link-name = "MultiMedia5";
 594                 cpu {
 595                         sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA5>;
 596                 };
 597         };
 598
 599         mm6-dai-link {
 600                 link-name = "MultiMedia6";
 601                 cpu {
 602                         sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA6>;
 603                 };
 604         };
 605
 606         speaker_playback_dai: speaker-dai-link {
 607                 link-name = "Speaker Playback";
 608                 cpu {
 609                         sound-dai = <&q6afedai QUATERNARY_MI2S_RX>;
 610                 };
 611
 612                 platform {
 613                         sound-dai = <&q6routing>;
 614                 };
 615         };
 616
 617         slim-dai-link {
 618                 link-name = "SLIM Playback 1";
 619                 cpu {
 620                         sound-dai = <&q6afedai SLIMBUS_0_RX>;
 621                 };
 622
 623                 platform {
 624                         sound-dai = <&q6routing>;
 625                 };
 626
 627                 codec {
 628                         sound-dai = <&wcd9340 0>;
 629                 };
 630         };
 631
 632         slimcap-dai-link {
 633                 link-name = "SLIM Capture 1";
 634                 cpu {
 635                         sound-dai = <&q6afedai SLIMBUS_0_TX>;
 636                 };
 637
 638                 platform {
 639                         sound-dai = <&q6routing>;
 640                 };
 641
 642                 codec {
 643                         sound-dai = <&wcd9340 1>;
 644                 };
 645         };
 646
 647         slim2-dai-link {
 648                 link-name = "SLIM Playback 2";
 649                 cpu {
 650                         sound-dai = <&q6afedai SLIMBUS_1_RX>;
 651                 };
 652
 653                 platform {
 654                         sound-dai = <&q6routing>;
 655                 };
 656
 657                 codec {
 658                         sound-dai = <&wcd9340 2>; /* AIF2_PB */
 659                 };
 660         };
 661
 662         slimcap2-dai-link {
 663                 link-name = "SLIM Capture 2";
 664                 cpu {
 665                         sound-dai = <&q6afedai SLIMBUS_1_TX>;
 666                 };
 667
 668                 platform {
 669                         sound-dai = <&q6routing>;
 670                 };
 671
 672                 codec {
 673                         sound-dai = <&wcd9340 3>; /* AIF2_CAP */
 674                 };
 675         };
 676
 677         slimcap3-dai-link {
 678                 link-name = "SLIM Capture 3";
 679                 cpu {
 680                         sound-dai = <&q6afedai SLIMBUS_2_TX>;
 681                 };
 682
 683                 platform {
 684                         sound-dai = <&q6routing>;
 685                 };
 686
 687                 codec {
 688                         sound-dai = <&wcd9340 5>; /* AIF3_CAP */
 689                 };
 690         };
 691 };
 692
 693 &uart6 {
 694         status = "okay";
 695
 696         pinctrl-0 = <&qup_uart6_4pin>;
 697
 698         bluetooth {
 699                 compatible = "qcom,wcn3990-bt";
 700
 701                 /*
 702                  * This path is relative to the qca/
 703                  * subdir under lib/firmware.
 704                  */
 705                 firmware-name = "oneplus6/crnv21.bin";
 706
 707                 vddio-supply = <&vreg_s4a_1p8>;
 708                 vddxo-supply = <&vreg_l7a_1p8>;
 709                 vddrf-supply = <&vreg_l17a_1p3>;
 710                 vddch0-supply = <&vreg_l25a_3p3>;
 711                 max-speed = <3200000>;
 712         };
 713 };
 714
 715 &uart9 {
 716         label = "LS-UART1";
 717         status = "okay";
 718 };
 719
 720 &ufs_mem_hc {
 721         status = "okay";
 722
 723         reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
 724
 725         vcc-supply = <&vreg_l20a_2p95>;
 726         vcc-max-microamp = <600000>;
 727 };
 728
 729 &ufs_mem_phy {
 730         status = "okay";
 731
 732         vdda-phy-supply = <&vdda_ufs1_core>;
 733         vdda-pll-supply = <&vdda_ufs1_1p2>;
 734 };
 735
 736 &usb_1 {
 737         status = "okay";
 738
 739         /*
 740          * disable USB3 clock requirement as the device only supports
 741          * USB2.
 742          */
 743         qcom,select-utmi-as-pipe-clk;
 744 };
 745
 746 &usb_1_dwc3 {
 747         /*
 748          * We don't have the capability to switch modes yet.
 749          */
 750         dr_mode = "peripheral";
 751
 752         /* fastest mode for USB 2 */
 753         maximum-speed = "high-speed";
 754
 755         /* Remove USB3 phy as it's unused on this device. */
 756         phys = <&usb_1_hsphy>;
 757         phy-names = "usb2-phy";
 758 };
 759
 760 &usb_1_hsphy {
 761         status = "okay";
 762
 763         vdd-supply = <&vdda_usb1_ss_core>;
 764         vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
 765         vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
 766
 767         qcom,imp-res-offset-value = <8>;
 768         qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
 769         qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
 770         qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
 771 };
 772
 773 &tlmm {
 774         gpio-reserved-ranges = <0 4>, <81 4>;
 775
 776         hall_sensor_default: hall-sensor-default-state {
 777                 pins = "gpio124";
 778                 function = "gpio";
 779                 drive-strength = <2>;
 780                 bias-disable;
 781         };
 782
 783         tri_state_key_default: tri-state-key-default-state {
 784                 pins = "gpio40", "gpio42", "gpio26";
 785                 function = "gpio";
 786                 drive-strength = <2>;
 787                 bias-disable;
 788         };
 789
 790         ts_default_pins: ts-int-state {
 791                 pins = "gpio99", "gpio125";
 792                 function = "gpio";
 793                 drive-strength = <16>;
 794                 bias-pull-up;
 795         };
 796
 797         panel_reset_pins: panel-reset-state {
 798                 pins = "gpio6", "gpio25", "gpio26";
 799                 function = "gpio";
 800                 drive-strength = <8>;
 801                 bias-disable;
 802         };
 803
 804         panel_te_pin: panel-te-state {
 805                 pins = "gpio10";
 806                 function = "mdp_vsync";
 807                 drive-strength = <2>;
 808                 bias-disable;
 809         };
 810
 811         panel_esd_pin: panel-esd-state {
 812                 pins = "gpio30";
 813                 function = "gpio";
 814                 drive-strength = <2>;
 815                 bias-pull-down;
 816         };
 817
 818         speaker_default: speaker-default-state {
 819                 pins = "gpio69";
 820                 function = "gpio";
 821                 drive-strength = <16>;
 822                 bias-pull-up;
 823                 output-high;
 824         };
 825 };
 826
 827 &venus {
 828         status = "okay";
 829         firmware-name = "qcom/sdm845/oneplus6/venus.mbn";
 830 };
 831
 832 &wcd9340 {
 833         pinctrl-0 = <&wcd_intr_default>;
 834         pinctrl-names = "default";
 835         reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
 836         vdd-buck-supply = <&vreg_s4a_1p8>;
 837         vdd-buck-sido-supply = <&vreg_s4a_1p8>;
 838         vdd-tx-supply = <&vreg_s4a_1p8>;
 839         vdd-rx-supply = <&vreg_s4a_1p8>;
 840         vdd-io-supply = <&vreg_s4a_1p8>;
 841 };
 842
 843 &wifi {
 844         status = "okay";
 845         vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
 846         vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 847         vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 848         vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 849         vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
 850
 851         qcom,snoc-host-cap-8bit-quirk;
 852 };