- None
Optional properties:
-- operating-points: Refer to Documentation/devicetree/bindings/opp/opp.txt for
+- operating-points: Refer to Documentation/devicetree/bindings/opp/opp-v1.yaml for
details. OPPs *must* be supplied either via DT, i.e. this property, or
populated at runtime.
- clock-latency: Specify the possible maximum transition latency for clock,
transition and not stable yet.
Please refer to Documentation/devicetree/bindings/clock/clock-bindings.txt for
generic clock consumer properties.
-- operating-points-v2: Please refer to Documentation/devicetree/bindings/opp/opp.txt
+- operating-points-v2: Please refer to Documentation/devicetree/bindings/opp/opp-v2.yaml
for detail.
- proc-supply: Regulator for Vproc of CPU cluster.
hardware' information respectively. The framework is then able to read
the DT and operate in the usual way.
-For more information about the expected DT format [See: ../opp/opp.txt].
-
Frequency Scaling only
----------------------
Located in CPU's node:
-- operating-points : [See: ../power/opp.txt]
+- operating-points : [See: ../power/opp-v1.yaml]
Example [safe]
--------------
Located in CPU's node:
-- operating-points-v2 : [See ../power/opp.txt]
+- operating-points-v2 : [See ../power/opp-v2.yaml]
Example [unsafe]
----------------
Required properties:
- clocks: Must contain an entry for the CPU clock.
See ../clocks/clock-bindings.txt for details.
-- operating-points-v2: See ../bindings/opp/opp.txt for details.
+- operating-points-v2: See ../bindings/opp/opp-v2.yaml for details.
- #cooling-cells: Should be 2. See ../thermal/thermal-cooling-devices.yaml for details.
For each opp entry in 'operating-points-v2' table:
- clocks: Phandles for clock specified in "clock-names" property
- clock-names : The name of clock used by the DFI, must be
"pclk_ddr_mon";
-- operating-points-v2: Refer to Documentation/devicetree/bindings/opp/opp.txt
+- operating-points-v2: Refer to Documentation/devicetree/bindings/opp/opp-v2.yaml
for details.
- center-supply: DMC supply node.
- status: Marks the node enabled/disabled.
resets = <&reset 0>, <&reset 1>;
};
- gpu_opp_table: opp_table0 {
+ gpu_opp_table: opp-table {
compatible = "operating-points-v2";
opp-533000000 {
#cooling-cells = <2>;
};
- gpu_opp_table: opp_table0 {
+ gpu_opp_table: opp-table {
compatible = "operating-points-v2";
opp-533000000 {
noc_opp_table: opp-table {
compatible = "operating-points-v2";
- opp-133M {
+ opp-133333333 {
opp-hz = /bits/ 64 <133333333>;
};
- opp-800M {
+ opp-800000000 {
opp-hz = /bits/ 64 <800000000>;
};
};
sun50i-cpufreq-nvmem driver reads the efuse value from the SoC to
provide the OPP framework with required information.
+allOf:
+ - $ref: opp-v2-base.yaml#
+
properties:
compatible:
const: allwinner,sun50i-h6-operating-points
properties:
opp-hz: true
+ clock-latency-ns: true
patternProperties:
"opp-microvolt-.*": true
--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/opp/opp-v1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic OPP (Operating Performance Points) v1 Bindings
+
+maintainers:
+ - Viresh Kumar <viresh.kumar@linaro.org>
+
+description: |+
+ Devices work at voltage-current-frequency combinations and some implementations
+ have the liberty of choosing these. These combinations are called Operating
+ Performance Points aka OPPs. This document defines bindings for these OPPs
+ applicable across wide range of devices. For illustration purpose, this document
+ uses CPU as a device.
+
+ This binding only supports voltage-frequency pairs.
+
+select: true
+
+properties:
+ operating-points:
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ items:
+ - description: Frequency in kHz
+ - description: Voltage for OPP in uV
+
+
+additionalProperties: true
+examples:
+ - |
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ operating-points =
+ /* kHz uV */
+ <792000 1100000>,
+ <396000 950000>,
+ <198000 850000>;
+ };
+ };
+...
--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/opp/opp-v2-base.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic OPP (Operating Performance Points) Common Binding
+
+maintainers:
+ - Viresh Kumar <viresh.kumar@linaro.org>
+
+description: |
+ Devices work at voltage-current-frequency combinations and some implementations
+ have the liberty of choosing these. These combinations are called Operating
+ Performance Points aka OPPs. This document defines bindings for these OPPs
+ applicable across wide range of devices. For illustration purpose, this document
+ uses CPU as a device.
+
+ This describes the OPPs belonging to a device.
+
+select: false
+
+properties:
+ $nodename:
+ pattern: '^opp-table(-[a-z0-9]+)?$'
+
+ opp-shared:
+ description:
+ Indicates that device nodes using this OPP Table Node's phandle switch
+ their DVFS state together, i.e. they share clock/voltage/current lines.
+ Missing property means devices have independent clock/voltage/current
+ lines, but they share OPP tables.
+ type: boolean
+
+patternProperties:
+ '^opp-?[0-9]+$':
+ type: object
+ description:
+ One or more OPP nodes describing voltage-current-frequency combinations.
+ Their name isn't significant but their phandle can be used to reference an
+ OPP. These are mandatory except for the case where the OPP table is
+ present only to indicate dependency between devices using the opp-shared
+ property.
+
+ properties:
+ opp-hz:
+ description:
+ Frequency in Hz, expressed as a 64-bit big-endian integer. This is a
+ required property for all device nodes, unless another "required"
+ property to uniquely identify the OPP nodes exists. Devices like power
+ domains must have another (implementation dependent) property.
+
+ opp-microvolt:
+ description: |
+ Voltage for the OPP
+
+ A single regulator's voltage is specified with an array of size one or three.
+ Single entry is for target voltage and three entries are for <target min max>
+ voltages.
+
+ Entries for multiple regulators shall be provided in the same field separated
+ by angular brackets <>. The OPP binding doesn't provide any provisions to
+ relate the values to their power supplies or the order in which the supplies
+ need to be configured and that is left for the implementation specific
+ binding.
+
+ Entries for all regulators shall be of the same size, i.e. either all use a
+ single value or triplets.
+ minItems: 1
+ maxItems: 8 # Should be enough regulators
+ items:
+ minItems: 1
+ maxItems: 3
+
+ opp-microamp:
+ description: |
+ The maximum current drawn by the device in microamperes considering
+ system specific parameters (such as transients, process, aging,
+ maximum operating temperature range etc.) as necessary. This may be
+ used to set the most efficient regulator operating mode.
+
+ Should only be set if opp-microvolt or opp-microvolt-<name> is set for
+ the OPP.
+
+ Entries for multiple regulators shall be provided in the same field
+ separated by angular brackets <>. If current values aren't required
+ for a regulator, then it shall be filled with 0. If current values
+ aren't required for any of the regulators, then this field is not
+ required. The OPP binding doesn't provide any provisions to relate the
+ values to their power supplies or the order in which the supplies need
+ to be configured and that is left for the implementation specific
+ binding.
+ minItems: 1
+ maxItems: 8 # Should be enough regulators
+
+ opp-level:
+ description:
+ A value representing the performance level of the device.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ opp-peak-kBps:
+ description:
+ Peak bandwidth in kilobytes per second, expressed as an array of
+ 32-bit big-endian integers. Each element of the array represents the
+ peak bandwidth value of each interconnect path. The number of elements
+ should match the number of interconnect paths.
+ minItems: 1
+ maxItems: 32 # Should be enough
+
+ opp-avg-kBps:
+ description:
+ Average bandwidth in kilobytes per second, expressed as an array
+ of 32-bit big-endian integers. Each element of the array represents the
+ average bandwidth value of each interconnect path. The number of elements
+ should match the number of interconnect paths. This property is only
+ meaningful in OPP tables where opp-peak-kBps is present.
+ minItems: 1
+ maxItems: 32 # Should be enough
+
+ clock-latency-ns:
+ description:
+ Specifies the maximum possible transition latency (in nanoseconds) for
+ switching to this OPP from any other OPP.
+
+ turbo-mode:
+ description:
+ Marks the OPP to be used only for turbo modes. Turbo mode is available
+ on some platforms, where the device can run over its operating
+ frequency for a short duration of time limited by the device's power,
+ current and thermal limits.
+ type: boolean
+
+ opp-suspend:
+ description:
+ Marks the OPP to be used during device suspend. If multiple OPPs in
+ the table have this, the OPP with highest opp-hz will be used.
+ type: boolean
+
+ opp-supported-hw:
+ description: |
+ This property allows a platform to enable only a subset of the OPPs
+ from the larger set present in the OPP table, based on the current
+ version of the hardware (already known to the operating system).
+
+ Each block present in the array of blocks in this property, represents
+ a sub-group of hardware versions supported by the OPP. i.e. <sub-group
+ A>, <sub-group B>, etc. The OPP will be enabled if _any_ of these
+ sub-groups match the hardware's version.
+
+ Each sub-group is a platform defined array representing the hierarchy
+ of hardware versions supported by the platform. For a platform with
+ three hierarchical levels of version (X.Y.Z), this field shall look
+ like
+
+ opp-supported-hw = <X1 Y1 Z1>, <X2 Y2 Z2>, <X3 Y3 Z3>.
+
+ Each level (eg. X1) in version hierarchy is represented by a 32 bit
+ value, one bit per version and so there can be maximum 32 versions per
+ level. Logical AND (&) operation is performed for each level with the
+ hardware's level version and a non-zero output for _all_ the levels in
+ a sub-group means the OPP is supported by hardware. A value of
+ 0xFFFFFFFF for each level in the sub-group will enable the OPP for all
+ versions for the hardware.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ maxItems: 32
+ items:
+ minItems: 1
+ maxItems: 4
+
+ required-opps:
+ description:
+ This contains phandle to an OPP node in another device's OPP table. It
+ may contain an array of phandles, where each phandle points to an OPP
+ of a different device. It should not contain multiple phandles to the
+ OPP nodes in the same OPP table. This specifies the minimum required
+ OPP of the device(s), whose OPP's phandle is present in this property,
+ for the functioning of the current device at the current OPP (where
+ this property is present).
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+
+ patternProperties:
+ '^opp-microvolt-':
+ description:
+ Named opp-microvolt property. This is exactly similar to the above
+ opp-microvolt property, but allows multiple voltage ranges to be
+ provided for the same OPP. At runtime, the platform can pick a <name>
+ and matching opp-microvolt-<name> property will be enabled for all
+ OPPs. If the platform doesn't pick a specific <name> or the <name>
+ doesn't match with any opp-microvolt-<name> properties, then
+ opp-microvolt property shall be used, if present.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ minItems: 1
+ maxItems: 8 # Should be enough regulators
+ items:
+ minItems: 1
+ maxItems: 3
+
+ '^opp-microamp-':
+ description:
+ Named opp-microamp property. Similar to opp-microvolt-<name> property,
+ but for microamp instead.
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 8 # Should be enough regulators
+
+ dependencies:
+ opp-avg-kBps: [ opp-peak-kBps ]
+
+required:
+ - compatible
+
+additionalProperties: true
+
+...
--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/opp/opp-v2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic OPP (Operating Performance Points) Bindings
+
+maintainers:
+ - Viresh Kumar <viresh.kumar@linaro.org>
+
+allOf:
+ - $ref: opp-v2-base.yaml#
+
+properties:
+ compatible:
+ const: operating-points-v2
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ /*
+ * Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states
+ * together.
+ */
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 0>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply0>;
+ operating-points-v2 = <&cpu0_opp_table0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 0>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply0>;
+ operating-points-v2 = <&cpu0_opp_table0>;
+ };
+ };
+
+ cpu0_opp_table0: opp-table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <975000 970000 985000>;
+ opp-microamp = <70000>;
+ clock-latency-ns = <300000>;
+ opp-suspend;
+ };
+ opp-1100000000 {
+ opp-hz = /bits/ 64 <1100000000>;
+ opp-microvolt = <1000000 980000 1010000>;
+ opp-microamp = <80000>;
+ clock-latency-ns = <310000>;
+ };
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1025000>;
+ clock-latency-ns = <290000>;
+ turbo-mode;
+ };
+ };
+
+ - |
+ /*
+ * Example 2: Single cluster, Quad-core Qualcom-krait, switches DVFS states
+ * independently.
+ */
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "qcom,krait";
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 0>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply0>;
+ operating-points-v2 = <&cpu_opp_table>;
+ };
+
+ cpu@1 {
+ compatible = "qcom,krait";
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 1>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply1>;
+ operating-points-v2 = <&cpu_opp_table>;
+ };
+
+ cpu@2 {
+ compatible = "qcom,krait";
+ device_type = "cpu";
+ reg = <2>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 2>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply2>;
+ operating-points-v2 = <&cpu_opp_table>;
+ };
+
+ cpu@3 {
+ compatible = "qcom,krait";
+ device_type = "cpu";
+ reg = <3>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 3>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply3>;
+ operating-points-v2 = <&cpu_opp_table>;
+ };
+ };
+
+ cpu_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ /*
+ * Missing opp-shared property means CPUs switch DVFS states
+ * independently.
+ */
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <975000 970000 985000>;
+ opp-microamp = <70000>;
+ clock-latency-ns = <300000>;
+ opp-suspend;
+ };
+ opp-1100000000 {
+ opp-hz = /bits/ 64 <1100000000>;
+ opp-microvolt = <1000000 980000 1010000>;
+ opp-microamp = <80000>;
+ clock-latency-ns = <310000>;
+ };
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1025000>;
+ opp-microamp = <90000>;
+ lock-latency-ns = <290000>;
+ turbo-mode;
+ };
+ };
+
+ - |
+ /*
+ * Example 3: Dual-cluster, Dual-core per cluster. CPUs within a cluster switch
+ * DVFS state together.
+ */
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 0>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply0>;
+ operating-points-v2 = <&cluster0_opp>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 0>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply0>;
+ operating-points-v2 = <&cluster0_opp>;
+ };
+
+ cpu@100 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <100>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 1>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply1>;
+ operating-points-v2 = <&cluster1_opp>;
+ };
+
+ cpu@101 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <101>;
+ next-level-cache = <&L2>;
+ clocks = <&clk_controller 1>;
+ clock-names = "cpu";
+ cpu-supply = <&cpu_supply1>;
+ operating-points-v2 = <&cluster1_opp>;
+ };
+ };
+
+ cluster0_opp: opp-table-0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <975000 970000 985000>;
+ opp-microamp = <70000>;
+ clock-latency-ns = <300000>;
+ opp-suspend;
+ };
+ opp-1100000000 {
+ opp-hz = /bits/ 64 <1100000000>;
+ opp-microvolt = <1000000 980000 1010000>;
+ opp-microamp = <80000>;
+ clock-latency-ns = <310000>;
+ };
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1025000>;
+ opp-microamp = <90000>;
+ clock-latency-ns = <290000>;
+ turbo-mode;
+ };
+ };
+
+ cluster1_opp: opp-table-1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-1300000000 {
+ opp-hz = /bits/ 64 <1300000000>;
+ opp-microvolt = <1050000 1045000 1055000>;
+ opp-microamp = <95000>;
+ clock-latency-ns = <400000>;
+ opp-suspend;
+ };
+ opp-1400000000 {
+ opp-hz = /bits/ 64 <1400000000>;
+ opp-microvolt = <1075000>;
+ opp-microamp = <100000>;
+ clock-latency-ns = <400000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1100000 1010000 1110000>;
+ opp-microamp = <95000>;
+ clock-latency-ns = <400000>;
+ turbo-mode;
+ };
+ };
+
+ - |
+ /* Example 4: Handling multiple regulators */
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "foo,cpu-type";
+ device_type = "cpu";
+ reg = <0>;
+
+ vcc0-supply = <&cpu_supply0>;
+ vcc1-supply = <&cpu_supply1>;
+ vcc2-supply = <&cpu_supply2>;
+ operating-points-v2 = <&cpu0_opp_table4>;
+ };
+ };
+
+ cpu0_opp_table4: opp-table-0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <970000>, /* Supply 0 */
+ <960000>, /* Supply 1 */
+ <960000>; /* Supply 2 */
+ opp-microamp = <70000>, /* Supply 0 */
+ <70000>, /* Supply 1 */
+ <70000>; /* Supply 2 */
+ clock-latency-ns = <300000>;
+ };
+
+ /* OR */
+
+ opp-1000000001 {
+ opp-hz = /bits/ 64 <1000000001>;
+ opp-microvolt = <975000 970000 985000>, /* Supply 0 */
+ <965000 960000 975000>, /* Supply 1 */
+ <965000 960000 975000>; /* Supply 2 */
+ opp-microamp = <70000>, /* Supply 0 */
+ <70000>, /* Supply 1 */
+ <70000>; /* Supply 2 */
+ clock-latency-ns = <300000>;
+ };
+
+ /* OR */
+
+ opp-1000000002 {
+ opp-hz = /bits/ 64 <1000000002>;
+ opp-microvolt = <975000 970000 985000>, /* Supply 0 */
+ <965000 960000 975000>, /* Supply 1 */
+ <965000 960000 975000>; /* Supply 2 */
+ opp-microamp = <70000>, /* Supply 0 */
+ <0>, /* Supply 1 doesn't need this */
+ <70000>; /* Supply 2 */
+ clock-latency-ns = <300000>;
+ };
+ };
+
+ - |
+ /*
+ * Example 5: opp-supported-hw
+ * (example: three level hierarchy of versions: cuts, substrate and process)
+ */
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ cpu-supply = <&cpu_supply>;
+ operating-points-v2 = <&cpu0_opp_table_slow>;
+ };
+ };
+
+ cpu0_opp_table_slow: opp-table {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-600000000 {
+ /*
+ * Supports all substrate and process versions for 0xF
+ * cuts, i.e. only first four cuts.
+ */
+ opp-supported-hw = <0xF 0xFFFFFFFF 0xFFFFFFFF>;
+ opp-hz = /bits/ 64 <600000000>;
+ };
+
+ opp-800000000 {
+ /*
+ * Supports:
+ * - cuts: only one, 6th cut (represented by 6th bit).
+ * - substrate: supports 16 different substrate versions
+ * - process: supports 9 different process versions
+ */
+ opp-supported-hw = <0x20 0xff0000ff 0x0000f4f0>;
+ opp-hz = /bits/ 64 <800000000>;
+ };
+
+ opp-900000000 {
+ /*
+ * Supports:
+ * - All cuts and substrate where process version is 0x2.
+ * - All cuts and process where substrate version is 0x2.
+ */
+ opp-supported-hw = <0xFFFFFFFF 0xFFFFFFFF 0x02>,
+ <0xFFFFFFFF 0x01 0xFFFFFFFF>;
+ opp-hz = /bits/ 64 <900000000>;
+ };
+ };
+
+ - |
+ /*
+ * Example 6: opp-microvolt-<name>, opp-microamp-<name>:
+ * (example: device with two possible microvolt ranges: slow and fast)
+ */
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ operating-points-v2 = <&cpu0_opp_table6>;
+ };
+ };
+
+ cpu0_opp_table6: opp-table-0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt-slow = <915000 900000 925000>;
+ opp-microvolt-fast = <975000 970000 985000>;
+ opp-microamp-slow = <70000>;
+ opp-microamp-fast = <71000>;
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt-slow = <915000 900000 925000>, /* Supply vcc0 */
+ <925000 910000 935000>; /* Supply vcc1 */
+ opp-microvolt-fast = <975000 970000 985000>, /* Supply vcc0 */
+ <965000 960000 975000>; /* Supply vcc1 */
+ opp-microamp = <70000>; /* Will be used for both slow/fast */
+ };
+ };
+
+ - |
+ /*
+ * Example 7: Single cluster Quad-core ARM cortex A53, OPP points from firmware,
+ * distinct clock controls but two sets of clock/voltage/current lines.
+ */
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x0 0x100>;
+ next-level-cache = <&A53_L2>;
+ clocks = <&dvfs_controller 0>;
+ operating-points-v2 = <&cpu_opp0_table>;
+ };
+ cpu@1 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x0 0x101>;
+ next-level-cache = <&A53_L2>;
+ clocks = <&dvfs_controller 1>;
+ operating-points-v2 = <&cpu_opp0_table>;
+ };
+ cpu@2 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x0 0x102>;
+ next-level-cache = <&A53_L2>;
+ clocks = <&dvfs_controller 2>;
+ operating-points-v2 = <&cpu_opp1_table>;
+ };
+ cpu@3 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x0 0x103>;
+ next-level-cache = <&A53_L2>;
+ clocks = <&dvfs_controller 3>;
+ operating-points-v2 = <&cpu_opp1_table>;
+ };
+
+ };
+
+ cpu_opp0_table: opp-table-0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+ };
+
+ cpu_opp1_table: opp-table-1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+ };
+...
+++ /dev/null
-Generic OPP (Operating Performance Points) Bindings
-----------------------------------------------------
-
-Devices work at voltage-current-frequency combinations and some implementations
-have the liberty of choosing these. These combinations are called Operating
-Performance Points aka OPPs. This document defines bindings for these OPPs
-applicable across wide range of devices. For illustration purpose, this document
-uses CPU as a device.
-
-This document contain multiple versions of OPP binding and only one of them
-should be used per device.
-
-Binding 1: operating-points
-============================
-
-This binding only supports voltage-frequency pairs.
-
-Properties:
-- operating-points: An array of 2-tuples items, and each item consists
- of frequency and voltage like <freq-kHz vol-uV>.
- freq: clock frequency in kHz
- vol: voltage in microvolt
-
-Examples:
-
-cpu@0 {
- compatible = "arm,cortex-a9";
- reg = <0>;
- next-level-cache = <&L2>;
- operating-points = <
- /* kHz uV */
- 792000 1100000
- 396000 950000
- 198000 850000
- >;
-};
-
-
-Binding 2: operating-points-v2
-============================
-
-* Property: operating-points-v2
-
-Devices supporting OPPs must set their "operating-points-v2" property with
-phandle to a OPP table in their DT node. The OPP core will use this phandle to
-find the operating points for the device.
-
-This can contain more than one phandle for power domain providers that provide
-multiple power domains. That is, one phandle for each power domain. If only one
-phandle is available, then the same OPP table will be used for all power domains
-provided by the power domain provider.
-
-If required, this can be extended for SoC vendor specific bindings. Such bindings
-should be documented as Documentation/devicetree/bindings/power/<vendor>-opp.txt
-and should have a compatible description like: "operating-points-v2-<vendor>".
-
-* OPP Table Node
-
-This describes the OPPs belonging to a device. This node can have following
-properties:
-
-Required properties:
-- compatible: Allow OPPs to express their compatibility. It should be:
- "operating-points-v2".
-
-- OPP nodes: One or more OPP nodes describing voltage-current-frequency
- combinations. Their name isn't significant but their phandle can be used to
- reference an OPP. These are mandatory except for the case where the OPP table
- is present only to indicate dependency between devices using the opp-shared
- property.
-
-Optional properties:
-- opp-shared: Indicates that device nodes using this OPP Table Node's phandle
- switch their DVFS state together, i.e. they share clock/voltage/current lines.
- Missing property means devices have independent clock/voltage/current lines,
- but they share OPP tables.
-
-- status: Marks the OPP table enabled/disabled.
-
-
-* OPP Node
-
-This defines voltage-current-frequency combinations along with other related
-properties.
-
-Required properties:
-- opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer. This is a
- required property for all device nodes, unless another "required" property to
- uniquely identify the OPP nodes exists. Devices like power domains must have
- another (implementation dependent) property.
-
-- opp-peak-kBps: Peak bandwidth in kilobytes per second, expressed as an array
- of 32-bit big-endian integers. Each element of the array represents the
- peak bandwidth value of each interconnect path. The number of elements should
- match the number of interconnect paths.
-
-Optional properties:
-- opp-microvolt: voltage in micro Volts.
-
- A single regulator's voltage is specified with an array of size one or three.
- Single entry is for target voltage and three entries are for <target min max>
- voltages.
-
- Entries for multiple regulators shall be provided in the same field separated
- by angular brackets <>. The OPP binding doesn't provide any provisions to
- relate the values to their power supplies or the order in which the supplies
- need to be configured and that is left for the implementation specific
- binding.
-
- Entries for all regulators shall be of the same size, i.e. either all use a
- single value or triplets.
-
-- opp-microvolt-<name>: Named opp-microvolt property. This is exactly similar to
- the above opp-microvolt property, but allows multiple voltage ranges to be
- provided for the same OPP. At runtime, the platform can pick a <name> and
- matching opp-microvolt-<name> property will be enabled for all OPPs. If the
- platform doesn't pick a specific <name> or the <name> doesn't match with any
- opp-microvolt-<name> properties, then opp-microvolt property shall be used, if
- present.
-
-- opp-microamp: The maximum current drawn by the device in microamperes
- considering system specific parameters (such as transients, process, aging,
- maximum operating temperature range etc.) as necessary. This may be used to
- set the most efficient regulator operating mode.
-
- Should only be set if opp-microvolt is set for the OPP.
-
- Entries for multiple regulators shall be provided in the same field separated
- by angular brackets <>. If current values aren't required for a regulator,
- then it shall be filled with 0. If current values aren't required for any of
- the regulators, then this field is not required. The OPP binding doesn't
- provide any provisions to relate the values to their power supplies or the
- order in which the supplies need to be configured and that is left for the
- implementation specific binding.
-
-- opp-microamp-<name>: Named opp-microamp property. Similar to
- opp-microvolt-<name> property, but for microamp instead.
-
-- opp-level: A value representing the performance level of the device,
- expressed as a 32-bit integer.
-
-- opp-avg-kBps: Average bandwidth in kilobytes per second, expressed as an array
- of 32-bit big-endian integers. Each element of the array represents the
- average bandwidth value of each interconnect path. The number of elements
- should match the number of interconnect paths. This property is only
- meaningful in OPP tables where opp-peak-kBps is present.
-
-- clock-latency-ns: Specifies the maximum possible transition latency (in
- nanoseconds) for switching to this OPP from any other OPP.
-
-- turbo-mode: Marks the OPP to be used only for turbo modes. Turbo mode is
- available on some platforms, where the device can run over its operating
- frequency for a short duration of time limited by the device's power, current
- and thermal limits.
-
-- opp-suspend: Marks the OPP to be used during device suspend. If multiple OPPs
- in the table have this, the OPP with highest opp-hz will be used.
-
-- opp-supported-hw: This property allows a platform to enable only a subset of
- the OPPs from the larger set present in the OPP table, based on the current
- version of the hardware (already known to the operating system).
-
- Each block present in the array of blocks in this property, represents a
- sub-group of hardware versions supported by the OPP. i.e. <sub-group A>,
- <sub-group B>, etc. The OPP will be enabled if _any_ of these sub-groups match
- the hardware's version.
-
- Each sub-group is a platform defined array representing the hierarchy of
- hardware versions supported by the platform. For a platform with three
- hierarchical levels of version (X.Y.Z), this field shall look like
-
- opp-supported-hw = <X1 Y1 Z1>, <X2 Y2 Z2>, <X3 Y3 Z3>.
-
- Each level (eg. X1) in version hierarchy is represented by a 32 bit value, one
- bit per version and so there can be maximum 32 versions per level. Logical AND
- (&) operation is performed for each level with the hardware's level version
- and a non-zero output for _all_ the levels in a sub-group means the OPP is
- supported by hardware. A value of 0xFFFFFFFF for each level in the sub-group
- will enable the OPP for all versions for the hardware.
-
-- status: Marks the node enabled/disabled.
-
-- required-opps: This contains phandle to an OPP node in another device's OPP
- table. It may contain an array of phandles, where each phandle points to an
- OPP of a different device. It should not contain multiple phandles to the OPP
- nodes in the same OPP table. This specifies the minimum required OPP of the
- device(s), whose OPP's phandle is present in this property, for the
- functioning of the current device at the current OPP (where this property is
- present).
-
-Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together.
-
-/ {
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a9";
- reg = <0>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 0>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply0>;
- operating-points-v2 = <&cpu0_opp_table>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a9";
- reg = <1>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 0>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply0>;
- operating-points-v2 = <&cpu0_opp_table>;
- };
- };
-
- cpu0_opp_table: opp_table0 {
- compatible = "operating-points-v2";
- opp-shared;
-
- opp-1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <975000 970000 985000>;
- opp-microamp = <70000>;
- clock-latency-ns = <300000>;
- opp-suspend;
- };
- opp-1100000000 {
- opp-hz = /bits/ 64 <1100000000>;
- opp-microvolt = <1000000 980000 1010000>;
- opp-microamp = <80000>;
- clock-latency-ns = <310000>;
- };
- opp-1200000000 {
- opp-hz = /bits/ 64 <1200000000>;
- opp-microvolt = <1025000>;
- clock-latency-ns = <290000>;
- turbo-mode;
- };
- };
-};
-
-Example 2: Single cluster, Quad-core Qualcom-krait, switches DVFS states
-independently.
-
-/ {
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "qcom,krait";
- reg = <0>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 0>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply0>;
- operating-points-v2 = <&cpu_opp_table>;
- };
-
- cpu@1 {
- compatible = "qcom,krait";
- reg = <1>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 1>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply1>;
- operating-points-v2 = <&cpu_opp_table>;
- };
-
- cpu@2 {
- compatible = "qcom,krait";
- reg = <2>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 2>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply2>;
- operating-points-v2 = <&cpu_opp_table>;
- };
-
- cpu@3 {
- compatible = "qcom,krait";
- reg = <3>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 3>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply3>;
- operating-points-v2 = <&cpu_opp_table>;
- };
- };
-
- cpu_opp_table: opp_table {
- compatible = "operating-points-v2";
-
- /*
- * Missing opp-shared property means CPUs switch DVFS states
- * independently.
- */
-
- opp-1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <975000 970000 985000>;
- opp-microamp = <70000>;
- clock-latency-ns = <300000>;
- opp-suspend;
- };
- opp-1100000000 {
- opp-hz = /bits/ 64 <1100000000>;
- opp-microvolt = <1000000 980000 1010000>;
- opp-microamp = <80000>;
- clock-latency-ns = <310000>;
- };
- opp-1200000000 {
- opp-hz = /bits/ 64 <1200000000>;
- opp-microvolt = <1025000>;
- opp-microamp = <90000;
- lock-latency-ns = <290000>;
- turbo-mode;
- };
- };
-};
-
-Example 3: Dual-cluster, Dual-core per cluster. CPUs within a cluster switch
-DVFS state together.
-
-/ {
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a7";
- reg = <0>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 0>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply0>;
- operating-points-v2 = <&cluster0_opp>;
- };
-
- cpu@1 {
- compatible = "arm,cortex-a7";
- reg = <1>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 0>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply0>;
- operating-points-v2 = <&cluster0_opp>;
- };
-
- cpu@100 {
- compatible = "arm,cortex-a15";
- reg = <100>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 1>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply1>;
- operating-points-v2 = <&cluster1_opp>;
- };
-
- cpu@101 {
- compatible = "arm,cortex-a15";
- reg = <101>;
- next-level-cache = <&L2>;
- clocks = <&clk_controller 1>;
- clock-names = "cpu";
- cpu-supply = <&cpu_supply1>;
- operating-points-v2 = <&cluster1_opp>;
- };
- };
-
- cluster0_opp: opp_table0 {
- compatible = "operating-points-v2";
- opp-shared;
-
- opp-1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <975000 970000 985000>;
- opp-microamp = <70000>;
- clock-latency-ns = <300000>;
- opp-suspend;
- };
- opp-1100000000 {
- opp-hz = /bits/ 64 <1100000000>;
- opp-microvolt = <1000000 980000 1010000>;
- opp-microamp = <80000>;
- clock-latency-ns = <310000>;
- };
- opp-1200000000 {
- opp-hz = /bits/ 64 <1200000000>;
- opp-microvolt = <1025000>;
- opp-microamp = <90000>;
- clock-latency-ns = <290000>;
- turbo-mode;
- };
- };
-
- cluster1_opp: opp_table1 {
- compatible = "operating-points-v2";
- opp-shared;
-
- opp-1300000000 {
- opp-hz = /bits/ 64 <1300000000>;
- opp-microvolt = <1050000 1045000 1055000>;
- opp-microamp = <95000>;
- clock-latency-ns = <400000>;
- opp-suspend;
- };
- opp-1400000000 {
- opp-hz = /bits/ 64 <1400000000>;
- opp-microvolt = <1075000>;
- opp-microamp = <100000>;
- clock-latency-ns = <400000>;
- };
- opp-1500000000 {
- opp-hz = /bits/ 64 <1500000000>;
- opp-microvolt = <1100000 1010000 1110000>;
- opp-microamp = <95000>;
- clock-latency-ns = <400000>;
- turbo-mode;
- };
- };
-};
-
-Example 4: Handling multiple regulators
-
-/ {
- cpus {
- cpu@0 {
- compatible = "vendor,cpu-type";
- ...
-
- vcc0-supply = <&cpu_supply0>;
- vcc1-supply = <&cpu_supply1>;
- vcc2-supply = <&cpu_supply2>;
- operating-points-v2 = <&cpu0_opp_table>;
- };
- };
-
- cpu0_opp_table: opp_table0 {
- compatible = "operating-points-v2";
- opp-shared;
-
- opp-1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <970000>, /* Supply 0 */
- <960000>, /* Supply 1 */
- <960000>; /* Supply 2 */
- opp-microamp = <70000>, /* Supply 0 */
- <70000>, /* Supply 1 */
- <70000>; /* Supply 2 */
- clock-latency-ns = <300000>;
- };
-
- /* OR */
-
- opp-1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <975000 970000 985000>, /* Supply 0 */
- <965000 960000 975000>, /* Supply 1 */
- <965000 960000 975000>; /* Supply 2 */
- opp-microamp = <70000>, /* Supply 0 */
- <70000>, /* Supply 1 */
- <70000>; /* Supply 2 */
- clock-latency-ns = <300000>;
- };
-
- /* OR */
-
- opp-1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt = <975000 970000 985000>, /* Supply 0 */
- <965000 960000 975000>, /* Supply 1 */
- <965000 960000 975000>; /* Supply 2 */
- opp-microamp = <70000>, /* Supply 0 */
- <0>, /* Supply 1 doesn't need this */
- <70000>; /* Supply 2 */
- clock-latency-ns = <300000>;
- };
- };
-};
-
-Example 5: opp-supported-hw
-(example: three level hierarchy of versions: cuts, substrate and process)
-
-/ {
- cpus {
- cpu@0 {
- compatible = "arm,cortex-a7";
- ...
-
- cpu-supply = <&cpu_supply>
- operating-points-v2 = <&cpu0_opp_table_slow>;
- };
- };
-
- opp_table {
- compatible = "operating-points-v2";
- opp-shared;
-
- opp-600000000 {
- /*
- * Supports all substrate and process versions for 0xF
- * cuts, i.e. only first four cuts.
- */
- opp-supported-hw = <0xF 0xFFFFFFFF 0xFFFFFFFF>
- opp-hz = /bits/ 64 <600000000>;
- ...
- };
-
- opp-800000000 {
- /*
- * Supports:
- * - cuts: only one, 6th cut (represented by 6th bit).
- * - substrate: supports 16 different substrate versions
- * - process: supports 9 different process versions
- */
- opp-supported-hw = <0x20 0xff0000ff 0x0000f4f0>
- opp-hz = /bits/ 64 <800000000>;
- ...
- };
-
- opp-900000000 {
- /*
- * Supports:
- * - All cuts and substrate where process version is 0x2.
- * - All cuts and process where substrate version is 0x2.
- */
- opp-supported-hw = <0xFFFFFFFF 0xFFFFFFFF 0x02>, <0xFFFFFFFF 0x01 0xFFFFFFFF>
- opp-hz = /bits/ 64 <900000000>;
- ...
- };
- };
-};
-
-Example 6: opp-microvolt-<name>, opp-microamp-<name>:
-(example: device with two possible microvolt ranges: slow and fast)
-
-/ {
- cpus {
- cpu@0 {
- compatible = "arm,cortex-a7";
- ...
-
- operating-points-v2 = <&cpu0_opp_table>;
- };
- };
-
- cpu0_opp_table: opp_table0 {
- compatible = "operating-points-v2";
- opp-shared;
-
- opp-1000000000 {
- opp-hz = /bits/ 64 <1000000000>;
- opp-microvolt-slow = <915000 900000 925000>;
- opp-microvolt-fast = <975000 970000 985000>;
- opp-microamp-slow = <70000>;
- opp-microamp-fast = <71000>;
- };
-
- opp-1200000000 {
- opp-hz = /bits/ 64 <1200000000>;
- opp-microvolt-slow = <915000 900000 925000>, /* Supply vcc0 */
- <925000 910000 935000>; /* Supply vcc1 */
- opp-microvolt-fast = <975000 970000 985000>, /* Supply vcc0 */
- <965000 960000 975000>; /* Supply vcc1 */
- opp-microamp = <70000>; /* Will be used for both slow/fast */
- };
- };
-};
-
-Example 7: Single cluster Quad-core ARM cortex A53, OPP points from firmware,
-distinct clock controls but two sets of clock/voltage/current lines.
-
-/ {
- cpus {
- #address-cells = <2>;
- #size-cells = <0>;
-
- cpu@0 {
- compatible = "arm,cortex-a53";
- reg = <0x0 0x100>;
- next-level-cache = <&A53_L2>;
- clocks = <&dvfs_controller 0>;
- operating-points-v2 = <&cpu_opp0_table>;
- };
- cpu@1 {
- compatible = "arm,cortex-a53";
- reg = <0x0 0x101>;
- next-level-cache = <&A53_L2>;
- clocks = <&dvfs_controller 1>;
- operating-points-v2 = <&cpu_opp0_table>;
- };
- cpu@2 {
- compatible = "arm,cortex-a53";
- reg = <0x0 0x102>;
- next-level-cache = <&A53_L2>;
- clocks = <&dvfs_controller 2>;
- operating-points-v2 = <&cpu_opp1_table>;
- };
- cpu@3 {
- compatible = "arm,cortex-a53";
- reg = <0x0 0x103>;
- next-level-cache = <&A53_L2>;
- clocks = <&dvfs_controller 3>;
- operating-points-v2 = <&cpu_opp1_table>;
- };
-
- };
-
- cpu_opp0_table: opp0_table {
- compatible = "operating-points-v2";
- opp-shared;
- };
-
- cpu_opp1_table: opp1_table {
- compatible = "operating-points-v2";
- opp-shared;
- };
-};
Qualcomm OPP bindings to describe OPP nodes
The bindings are based on top of the operating-points-v2 bindings
-described in Documentation/devicetree/bindings/opp/opp.txt
+described in Documentation/devicetree/bindings/opp/opp-v2-base.yaml
Additional properties are described below.
* OPP Table Node
of the multi regulator binding that is part of the OPP core described here [1]
to describe both regulators needed by the platform.
-[1] Documentation/devicetree/bindings/opp/opp.txt
+[1] Documentation/devicetree/bindings/opp/opp-v2.yaml
Required Properties for Device Node:
- vdd-supply: phandle to regulator controlling VDD supply
Phandles to the OPP tables of power domains provided by a power domain
provider. If the provider provides a single power domain only or all
the power domains provided by the provider have identical OPP tables,
- then this shall contain a single phandle. Refer to ../opp/opp.txt
+ then this shall contain a single phandle. Refer to ../opp/opp-v2-base.yaml
for more information.
"#power-domain-cells":
};
};
- /* see Documentation/devicetree/bindings/opp/opp.txt */
cpu0_opp_table: opp-table {
compatible = "operating-points-v2-ti-cpu";
syscon = <&scm_conf>;
};
};
- /* see Documentation/devicetree/bindings/opp/opp.txt */
cpu0_opp_table: opp-table {
compatible = "operating-points-v2-ti-cpu";
syscon = <&scm_conf>;
projects / linux-2.6-microblaze.git / commitdiff