- i2c-bus-name: The name of this bus. Also needed as pinctrl-name for the I2C
parents.
-Furthermore, I2C mux properties and child nodes. See i2c-mux.txt in this
+Furthermore, I2C mux properties and child nodes. See i2c-mux.yaml in this
directory.
Example:
- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
port is connected to.
- mux-gpios: list of gpios used to control the muxer
-* Standard I2C mux properties. See i2c-mux.txt in this directory.
-* I2C child bus nodes. See i2c-mux.txt in this directory.
+* Standard I2C mux properties. See i2c-mux.yaml in this directory.
+* I2C child bus nodes. See i2c-mux.yaml in this directory.
Optional properties:
- idle-state: value to set the muxer to when idle. When no value is
+++ /dev/null
-General Purpose I2C Bus Mux
-
-This binding describes an I2C bus multiplexer that uses a mux controller
-from the mux subsystem to route the I2C signals.
-
- .-----. .-----.
- | dev | | dev |
- .------------. '-----' '-----'
- | SoC | | |
- | | .--------+--------'
- | .------. | .------+ child bus A, on MUX value set to 0
- | | I2C |-|--| Mux |
- | '------' | '--+---+ child bus B, on MUX value set to 1
- | .------. | | '----------+--------+--------.
- | | MUX- | | | | | |
- | | Ctrl |-|-----+ .-----. .-----. .-----.
- | '------' | | dev | | dev | | dev |
- '------------' '-----' '-----' '-----'
-
-Required properties:
-- compatible: i2c-mux
-- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
- port is connected to.
-- mux-controls: The phandle of the mux controller to use for operating the
- mux.
-* Standard I2C mux properties. See i2c-mux.txt in this directory.
-* I2C child bus nodes. See i2c-mux.txt in this directory. The sub-bus number
- is also the mux-controller state described in ../mux/mux-controller.yaml
-
-Optional properties:
-- mux-locked: If present, explicitly allow unrelated I2C transactions on the
- parent I2C adapter at these times:
- + during setup of the multiplexer
- + between setup of the multiplexer and the child bus I2C transaction
- + between the child bus I2C transaction and releasing of the multiplexer
- + during releasing of the multiplexer
- However, I2C transactions to devices behind all I2C multiplexers connected
- to the same parent adapter that this multiplexer is connected to are blocked
- for the full duration of the complete multiplexed I2C transaction (i.e.
- including the times covered by the above list).
- If mux-locked is not present, the multiplexer is assumed to be parent-locked.
- This means that no unrelated I2C transactions are allowed on the parent I2C
- adapter for the complete multiplexed I2C transaction.
- The properties of mux-locked and parent-locked multiplexers are discussed
- in more detail in Documentation/i2c/i2c-topology.rst.
-
-For each i2c child node, an I2C child bus will be created. They will
-be numbered based on their order in the device tree.
-
-Whenever an access is made to a device on a child bus, the value set
-in the relevant node's reg property will be set as the state in the
-mux controller.
-
-Example:
- mux: mux-controller {
- compatible = "gpio-mux";
- #mux-control-cells = <0>;
-
- mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
- <&pioA 1 GPIO_ACTIVE_HIGH>;
- };
-
- i2c-mux {
- compatible = "i2c-mux";
- mux-locked;
- i2c-parent = <&i2c1>;
-
- mux-controls = <&mux>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- i2c@1 {
- reg = <1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- ssd1307: oled@3c {
- compatible = "solomon,ssd1307fb-i2c";
- reg = <0x3c>;
- pwms = <&pwm 4 3000>;
- reset-gpios = <&gpio2 7 1>;
- reset-active-low;
- };
- };
-
- i2c@3 {
- reg = <3>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- pca9555: pca9555@20 {
- compatible = "nxp,pca9555";
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x20>;
- };
- };
- };
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/i2c-mux-gpmux.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: General Purpose I2C Bus Mux
+
+maintainers:
+ - Peter Rosin <peda@axentia.se>
+
+description: |+
+ This binding describes an I2C bus multiplexer that uses a mux controller
+ from the mux subsystem to route the I2C signals.
+
+ .-----. .-----.
+ | dev | | dev |
+ .------------. '-----' '-----'
+ | SoC | | |
+ | | .--------+--------'
+ | .------. | .------+ child bus A, on MUX value set to 0
+ | | I2C |-|--| Mux |
+ | '------' | '--+---+ child bus B, on MUX value set to 1
+ | .------. | | '----------+--------+--------.
+ | | MUX- | | | | | |
+ | | Ctrl |-|-----+ .-----. .-----. .-----.
+ | '------' | | dev | | dev | | dev |
+ '------------' '-----' '-----' '-----'
+
+
+
+allOf:
+ - $ref: /schemas/i2c/i2c-mux.yaml#
+
+properties:
+ compatible:
+ const: i2c-mux
+
+ i2c-parent:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ The phandle of the I2C bus that this multiplexer's master-side port is
+ connected to.
+
+ mux-controls:
+ maxItems: 1
+ description:
+ The mux-controller states are the I2C sub-bus numbers.
+
+ mux-locked:
+ type: boolean
+ description: |
+ Explicitly allow unrelated I2C transactions on the parent I2C adapter at
+ these times:
+ - during setup of the multiplexer
+ - between setup of the multiplexer and the child bus I2C transaction
+ - between the child bus I2C transaction and releasing of the multiplexer
+ - during releasing of the multiplexer
+
+ However, I2C transactions to devices behind all I2C multiplexers connected
+ to the same parent adapter that this multiplexer is connected to are blocked
+ for the full duration of the complete multiplexed I2C transaction (i.e.
+ including the times covered by the above list).
+ If mux-locked is not present, the multiplexer is assumed to be parent-locked.
+ This means that no unrelated I2C transactions are allowed on the parent I2C
+ adapter for the complete multiplexed I2C transaction.
+ The properties of mux-locked and parent-locked multiplexers are discussed
+ in more detail in Documentation/i2c/i2c-topology.rst.
+
+required:
+ - compatible
+ - i2c-parent
+ - mux-controls
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ mux: mux-controller {
+ compatible = "gpio-mux";
+ #mux-control-cells = <0>;
+
+ mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
+ <&pioA 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ i2c-mux {
+ compatible = "i2c-mux";
+ mux-locked;
+ i2c-parent = <&i2c1>;
+
+ mux-controls = <&mux>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio@20 {
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio@20 {
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ };
+ };
+ };
+...
The following required properties are defined externally:
- - Standard I2C mux properties. See i2c-mux.txt in this directory.
- - I2C child bus nodes. See i2c-mux.txt in this directory.
+ - Standard I2C mux properties. See i2c-mux.yaml in this directory.
+ - I2C child bus nodes. See i2c-mux.yaml in this directory.
Optional Properties:
* Standard pinctrl properties that specify the pin mux state for each child
bus. See ../pinctrl/pinctrl-bindings.txt.
-* Standard I2C mux properties. See i2c-mux.txt in this directory.
+* Standard I2C mux properties. See i2c-mux.yaml in this directory.
-* I2C child bus nodes. See i2c-mux.txt in this directory.
+* I2C child bus nodes. See i2c-mux.yaml in this directory.
For each named state defined in the pinctrl-names property, an I2C child bus
will be created. I2C child bus numbers are assigned based on the index into
- compatible: i2c-mux-reg
- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
port is connected to.
-* Standard I2C mux properties. See i2c-mux.txt in this directory.
-* I2C child bus nodes. See i2c-mux.txt in this directory.
+* Standard I2C mux properties. See i2c-mux.yaml in this directory.
+* I2C child bus nodes. See i2c-mux.yaml in this directory.
Optional properties:
- reg: this pair of <offset size> specifies the register to control the mux.
+++ /dev/null
-Common i2c bus multiplexer/switch properties.
-
-An i2c bus multiplexer/switch will have several child busses that are
-numbered uniquely in a device dependent manner. The nodes for an i2c bus
-multiplexer/switch will have one child node for each child bus.
-
-Optional properties:
-- #address-cells = <1>;
- This property is required if the i2c-mux child node does not exist.
-
-- #size-cells = <0>;
- This property is required if the i2c-mux child node does not exist.
-
-- i2c-mux
- For i2c multiplexers/switches that have child nodes that are a mixture
- of both i2c child busses and other child nodes, the 'i2c-mux' subnode
- can be used for populating the i2c child busses. If an 'i2c-mux'
- subnode is present, only subnodes of this will be considered as i2c
- child busses.
-
-Required properties for the i2c-mux child node:
-- #address-cells = <1>;
-- #size-cells = <0>;
-
-Required properties for i2c child bus nodes:
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg : The sub-bus number.
-
-Optional properties for i2c child bus nodes:
-- Other properties specific to the multiplexer/switch hardware.
-- Child nodes conforming to i2c bus binding
-
-
-Example :
-
- /*
- An NXP pca9548 8 channel I2C multiplexer at address 0x70
- with two NXP pca8574 GPIO expanders attached, one each to
- ports 3 and 4.
- */
-
- mux@70 {
- compatible = "nxp,pca9548";
- reg = <0x70>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- i2c@3 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <3>;
-
- gpio1: gpio@38 {
- compatible = "nxp,pca8574";
- reg = <0x38>;
- #gpio-cells = <2>;
- gpio-controller;
- };
- };
- i2c@4 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <4>;
-
- gpio2: gpio@38 {
- compatible = "nxp,pca8574";
- reg = <0x38>;
- #gpio-cells = <2>;
- gpio-controller;
- };
- };
- };
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/i2c-mux.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Common i2c bus multiplexer/switch properties.
+
+maintainers:
+ - Peter Rosin <peda@axentia.se>
+
+description: |+
+ An i2c bus multiplexer/switch will have several child busses that are numbered
+ uniquely in a device dependent manner. The nodes for an i2c bus
+ multiplexer/switch will have one child node for each child bus.
+
+ For i2c multiplexers/switches that have child nodes that are a mixture of both
+ i2c child busses and other child nodes, the 'i2c-mux' subnode can be used for
+ populating the i2c child busses. If an 'i2c-mux' subnode is present, only
+ subnodes of this will be considered as i2c child busses.
+
+properties:
+ $nodename:
+ pattern: '^(i2c-?)?mux'
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+patternProperties:
+ '^i2c@[0-9a-f]+$':
+ $ref: /schemas/i2c/i2c-controller.yaml
+ unevaluatedProperties: false
+
+ properties:
+ reg:
+ description: The mux selector sub-bus number for the child I2C bus.
+ maxItems: 1
+
+additionalProperties: true
+
+examples:
+ - |
+ /*
+ * An NXP pca9548 8 channel I2C multiplexer at address 0x70
+ * with two NXP pca8574 GPIO expanders attached, one each to
+ * ports 3 and 4.
+ */
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9548";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ gpio@20 {
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ };
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+
+ gpio@20 {
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ };
+ };
+ };
+ };
+...
projects / linux-2.6-microblaze.git / commitdiff