*/
#include <linux/mm.h>
-#include <linux/irq.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/config.h>
int apic_version [MAX_APICS];
unsigned char mp_bus_id_to_type [MAX_MP_BUSSES] = { [0 ... MAX_MP_BUSSES-1] = -1 };
int mp_bus_id_to_pci_bus [MAX_MP_BUSSES] = { [0 ... MAX_MP_BUSSES-1] = -1 };
-unsigned char pci_bus_to_node [256];
-EXPORT_SYMBOL(pci_bus_to_node);
static int mp_current_pci_id = 0;
/* I/O APIC entries */
physid_mask_t phys_cpu_present_map = PHYSID_MASK_NONE;
/* ACPI MADT entry parsing functions */
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
extern struct acpi_boot_flags acpi_boot;
#ifdef CONFIG_X86_LOCAL_APIC
extern int acpi_parse_lapic (acpi_table_entry_header *header);
#ifdef CONFIG_X86_IO_APIC
extern int acpi_parse_ioapic (acpi_table_entry_header *header);
#endif /*CONFIG_X86_IO_APIC*/
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /*CONFIG_ACPI*/
u8 bios_cpu_apicid[NR_CPUS] = { [0 ... NR_CPUS-1] = BAD_APICID };
static void __init MP_processor_info (struct mpc_config_processor *m)
{
- int ver;
+ int ver, cpu;
static int found_bsp=0;
if (!(m->mpc_cpuflag & CPU_ENABLED))
return;
}
- num_processors++;
+ cpu = num_processors++;
if (m->mpc_apicid > MAX_APICS) {
printk(KERN_ERR "Processor #%d INVALID. (Max ID: %d).\n",
* in same order as logical cpu numbers. Hence the first
* entry is BSP, and so on.
*/
+ cpu = 0;
+
bios_cpu_apicid[0] = m->mpc_apicid;
x86_cpu_to_apicid[0] = m->mpc_apicid;
found_bsp = 1;
- } else {
- bios_cpu_apicid[num_processors - found_bsp] = m->mpc_apicid;
- x86_cpu_to_apicid[num_processors - found_bsp] = m->mpc_apicid;
- }
+ } else
+ cpu = num_processors - found_bsp;
+ bios_cpu_apicid[cpu] = m->mpc_apicid;
+ x86_cpu_to_apicid[cpu] = m->mpc_apicid;
+
+ cpu_set(cpu, cpu_possible_map);
+ cpu_set(cpu, cpu_present_map);
}
static void __init MP_bus_info (struct mpc_config_bus *m)
m->mpc_irqtype, m->mpc_irqflag & 3,
(m->mpc_irqflag >> 2) & 3, m->mpc_srcbus,
m->mpc_srcbusirq, m->mpc_dstapic, m->mpc_dstirq);
- if (++mp_irq_entries == MAX_IRQ_SOURCES)
+ if (++mp_irq_entries >= MAX_IRQ_SOURCES)
panic("Max # of irq sources exceeded!!\n");
}
struct intel_mp_floating *mpf = mpf_found;
/*
- * ACPI may be used to obtain the entire SMP configuration or just to
- * enumerate/configure processors (CONFIG_ACPI_BOOT). Note that
* ACPI supports both logical (e.g. Hyper-Threading) and physical
* processors, where MPS only supports physical.
*/
* Read the physical hardware table. Anything here will
* override the defaults.
*/
- if (!smp_read_mpc((void *)(unsigned long)mpf->mpf_physptr)) {
+ if (!smp_read_mpc(phys_to_virt(mpf->mpf_physptr))) {
smp_found_config = 0;
printk(KERN_ERR "BIOS bug, MP table errors detected!...\n");
printk(KERN_ERR "... disabling SMP support. (tell your hw vendor)\n");
ACPI-based MP Configuration
-------------------------------------------------------------------------- */
-#ifdef CONFIG_ACPI_BOOT
+#ifdef CONFIG_ACPI
void __init mp_register_lapic_address (
u64 address)
processor.mpc_type = MP_PROCESSOR;
processor.mpc_apicid = id;
- processor.mpc_apicver = 0x10; /* TBD: lapic version */
+ processor.mpc_apicver = GET_APIC_VERSION(apic_read(APIC_LVR));
processor.mpc_cpuflag = (enabled ? CPU_ENABLED : 0);
processor.mpc_cpuflag |= (boot_cpu ? CPU_BOOTPROCESSOR : 0);
processor.mpc_cpufeature = (boot_cpu_data.x86 << 8) |
if (acpi_irq_model != ACPI_IRQ_MODEL_IOAPIC)
return gsi;
-#ifdef CONFIG_ACPI_BUS
/* Don't set up the ACPI SCI because it's already set up */
if (acpi_fadt.sci_int == gsi)
return gsi;
-#endif
ioapic = mp_find_ioapic(gsi);
if (ioapic < 0) {
* due to unused I/O APIC pins.
*/
int irq = gsi;
- gsi = pci_irq++;
- gsi_to_irq[irq] = gsi;
+ if (gsi < MAX_GSI_NUM) {
+ if (gsi > 15)
+ gsi = pci_irq++;
+ /*
+ * Don't assign IRQ used by ACPI SCI
+ */
+ if (gsi == acpi_fadt.sci_int)
+ gsi = pci_irq++;
+ gsi_to_irq[irq] = gsi;
+ } else {
+ printk(KERN_ERR "GSI %u is too high\n", gsi);
+ return gsi;
+ }
}
io_apic_set_pci_routing(ioapic, ioapic_pin, gsi,
}
#endif /*CONFIG_X86_IO_APIC*/
-#endif /*CONFIG_ACPI_BOOT*/
+#endif /*CONFIG_ACPI*/