Writing camera sensor drivers
=============================
-CSI-2
------
+CSI-2 and parallel (BT.601 and BT.656) busses
+---------------------------------------------
-Please see what is written on :ref:`MIPI_CSI_2`.
+Please see :ref:`transmitter-receiver`.
Handling clocks
---------------
ACPI
~~~~
-Read the "clock-frequency" _DSD property to denote the frequency. The driver can
-rely on this frequency being used.
+Read the ``clock-frequency`` _DSD property to denote the frequency. The driver
+can rely on this frequency being used.
Devicetree
~~~~~~~~~~
-The currently preferred way to achieve this is using "assigned-clock-rates"
-property. See Documentation/devicetree/bindings/clock/clock-bindings.txt for
-more information. The driver then gets the frequency using clk_get_rate().
+The currently preferred way to achieve this is using ``assigned-clocks``,
+``assigned-clock-parents`` and ``assigned-clock-rates`` properties. See
+``Documentation/devicetree/bindings/clock/clock-bindings.txt`` for more
+information. The driver then gets the frequency using ``clk_get_rate()``.
This approach has the drawback that there's no guarantee that the frequency
hasn't been modified directly or indirectly by another driver, or supported by
scaling configurations. The output size of the device is the result of a series
of cropping and scaling operations from the device's pixel array's size.
-An example of such a driver is the smiapp driver (see drivers/media/i2c/smiapp).
+An example of such a driver is the CCS driver (see ``drivers/media/i2c/ccs``).
Register list based drivers
~~~~~~~~~~~~~~~~~~~~~~~~~~~
format set on a source pad at the end of the device's internal pipeline.
Most sensor drivers are implemented this way, see e.g.
-drivers/media/i2c/imx319.c for an example.
+``drivers/media/i2c/imx319.c`` for an example.
Frame interval configuration
----------------------------
crop, use the full source image size, i.e. pixel array size.
Horizontal and vertical blanking are specified by ``V4L2_CID_HBLANK`` and
-``V4L2_CID_VBLANK``, respectively. The unit of these controls are lines. The
-pixel rate is specified by ``V4L2_CID_PIXEL_RATE`` in the same sub-device. The
-unit of that control is Hz.
+``V4L2_CID_VBLANK``, respectively. The unit of the ``V4L2_CID_HBLANK`` control
+is pixels and the unit of the ``V4L2_CID_VBLANK`` is lines. The pixel rate in
+the sensor's **pixel array** is specified by ``V4L2_CID_PIXEL_RATE`` in the same
+sub-device. The unit of that control is pixels per second.
Register list based drivers need to implement read-only sub-device nodes for the
purpose. Devices that are not register list based need these to configure the
accessed and when it is streaming.
Existing camera sensor drivers may rely on the old
-:c:type:`v4l2_subdev_core_ops`->s_power() callback for bridge or ISP drivers to
+struct v4l2_subdev_core_ops->s_power() callback for bridge or ISP drivers to
manage their power state. This is however **deprecated**. If you feel you need
to begin calling an s_power from an ISP or a bridge driver, instead please add
runtime PM support to the sensor driver you are using. Likewise, new drivers
should not use s_power.
Please see examples in e.g. ``drivers/media/i2c/ov8856.c`` and
-``drivers/media/i2c/smiapp/smiapp-core.c``. The two drivers work in both ACPI
+``drivers/media/i2c/ccs/ccs-core.c``. The two drivers work in both ACPI
and DT based systems.
Control framework
The function returns a non-zero value if it succeeded getting the power count or
runtime PM was disabled, in either of which cases the driver may proceed to
access the device.
-
-Controls
---------
-
-For camera sensors that are connected to a bus where transmitter and receiver
-require common configuration set by drivers, such as CSI-2 or parallel (BT.601
-or BT.656) bus, the ``V4L2_CID_LINK_FREQ`` control is mandatory on transmitter
-drivers. Receiver drivers can use the ``V4L2_CID_LINK_FREQ`` to query the
-frequency used on the bus.
-
-The transmitter drivers should also implement ``V4L2_CID_PIXEL_RATE`` control in
-order to tell the maximum pixel rate to the receiver. This is required on raw
-camera sensors.