arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi

   1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
   2 /*
   3  * Google Trogdor device tree source (common between revisions)
   4  *
   5  * Copyright 2019 Google LLC.
   6  */
   7
   8 #include <dt-bindings/gpio/gpio.h>
   9 #include <dt-bindings/input/gpio-keys.h>
  10 #include <dt-bindings/input/input.h>
  11 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
  12 #include <dt-bindings/sound/sc7180-lpass.h>
  13
  14 /* PMICs depend on spmi_bus label and so must come after SoC */
  15 #include "pm6150.dtsi"
  16 #include "pm6150l.dtsi"
  17
  18 / {
  19         thermal-zones {
  20                 charger_thermal: charger-thermal {
  21                         polling-delay-passive = <0>;
  22                         polling-delay = <0>;
  23
  24                         thermal-sensors = <&pm6150_adc_tm 0>;
  25
  26                         trips {
  27                                 charger-crit {
  28                                         temperature = <125000>;
  29                                         hysteresis = <1000>;
  30                                         type = "critical";
  31                                 };
  32                         };
  33                 };
  34         };
  35 };
  36
  37 /*
  38  * Reserved memory changes
  39  *
  40  * Delete all unused memory nodes and define the peripheral memory regions
  41  * required by the board dts.
  42  */
  43
  44 /delete-node/ &hyp_mem;
  45 /delete-node/ &xbl_mem;
  46 /delete-node/ &aop_mem;
  47 /delete-node/ &sec_apps_mem;
  48 /delete-node/ &tz_mem;
  49
  50 /* Increase the size from 2MB to 8MB */
  51 &rmtfs_mem {
  52         reg = <0x0 0x94600000 0x0 0x800000>;
  53 };
  54
  55 / {
  56         reserved-memory {
  57                 atf_mem: memory@80b00000 {
  58                         reg = <0x0 0x80b00000 0x0 0x100000>;
  59                         no-map;
  60                 };
  61
  62                 mpss_mem: memory@86000000 {
  63                         reg = <0x0 0x86000000 0x0 0x2000000>;
  64                         no-map;
  65                 };
  66
  67                 venus_mem: memory@8f600000 {
  68                         reg = <0 0x8f600000 0 0x500000>;
  69                         no-map;
  70                 };
  71
  72                 wlan_mem: memory@94100000 {
  73                         reg = <0x0 0x94100000 0x0 0x200000>;
  74                         no-map;
  75                 };
  76
  77                 mba_mem: memory@94400000 {
  78                         reg = <0x0 0x94400000 0x0 0x200000>;
  79                         no-map;
  80                 };
  81         };
  82
  83         aliases {
  84                 bluetooth0 = &bluetooth;
  85                 hsuart0 = &uart3;
  86                 serial0 = &uart8;
  87                 wifi0 = &wifi;
  88         };
  89
  90         chosen {
  91                 stdout-path = "serial0:115200n8";
  92         };
  93
  94         /* FIXED REGULATORS - parents above children */
  95
  96         /* This is the top level supply and variable voltage */
  97         ppvar_sys: ppvar-sys-regulator {
  98                 compatible = "regulator-fixed";
  99                 regulator-name = "ppvar_sys";
 100                 regulator-always-on;
 101                 regulator-boot-on;
 102         };
 103
 104         /* This divides ppvar_sys by 2, so voltage is variable */
 105         src_vph_pwr: src-vph-pwr-regulator {
 106                 compatible = "regulator-fixed";
 107                 regulator-name = "src_vph_pwr";
 108
 109                 /* EC turns on with switchcap_on; always on for AP */
 110                 regulator-always-on;
 111                 regulator-boot-on;
 112
 113                 vin-supply = <&ppvar_sys>;
 114         };
 115
 116         pp5000_a: pp5000-a-regulator {
 117                 compatible = "regulator-fixed";
 118                 regulator-name = "pp5000_a";
 119
 120                 /* EC turns on with en_pp5000_a; always on for AP */
 121                 regulator-always-on;
 122                 regulator-boot-on;
 123                 regulator-min-microvolt = <5000000>;
 124                 regulator-max-microvolt = <5000000>;
 125
 126                 vin-supply = <&ppvar_sys>;
 127         };
 128
 129         pp3300_a: pp3300-a-regulator {
 130                 compatible = "regulator-fixed";
 131                 regulator-name = "pp3300_a";
 132
 133                 /* EC turns on with en_pp3300_a; always on for AP */
 134                 regulator-always-on;
 135                 regulator-boot-on;
 136                 regulator-min-microvolt = <3300000>;
 137                 regulator-max-microvolt = <3300000>;
 138
 139                 /*
 140                  * Actually should be pp3300 but that's practically an alias for
 141                  * pp3300_a so we use pp3300's vin-supply here to avoid one more
 142                  * node.
 143                  */
 144                 vin-supply = <&ppvar_sys>;
 145         };
 146
 147         pp3300_audio:
 148         pp3300_codec: pp3300-codec-regulator {
 149                 compatible = "regulator-fixed";
 150                 regulator-name = "pp3300_codec";
 151
 152                 regulator-min-microvolt = <3300000>;
 153                 regulator-max-microvolt = <3300000>;
 154
 155                 gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>;
 156                 enable-active-high;
 157                 pinctrl-names = "default";
 158                 pinctrl-0 = <&en_pp3300_codec>;
 159
 160                 vin-supply = <&pp3300_a>;
 161         };
 162
 163         pp3300_dx_edp:
 164         pp3300_ts: pp3300-dx-edp-regulator {
 165                 compatible = "regulator-fixed";
 166                 regulator-name = "pp3300_dx_edp";
 167
 168                 regulator-min-microvolt = <3300000>;
 169                 regulator-max-microvolt = <3300000>;
 170
 171                 gpio = <&tlmm 30 GPIO_ACTIVE_HIGH>;
 172                 enable-active-high;
 173                 pinctrl-names = "default";
 174                 pinctrl-0 = <&en_pp3300_dx_edp>;
 175
 176                 vin-supply = <&pp3300_a>;
 177         };
 178
 179         pp3300_fp_tp: pp3300-fp-tp-regulator {
 180                 compatible = "regulator-fixed";
 181                 regulator-name = "pp3300_fp_tp";
 182
 183                 regulator-min-microvolt = <3300000>;
 184                 regulator-max-microvolt = <3300000>;
 185
 186                 /* AP turns on with PP1800_VIO_OUT; always on for AP */
 187                 regulator-always-on;
 188                 regulator-boot-on;
 189
 190                 vin-supply = <&pp3300_a>;
 191         };
 192
 193         pp3300_hub: pp3300-hub {
 194                 compatible = "regulator-fixed";
 195                 regulator-name = "pp3300_hub";
 196
 197                 regulator-min-microvolt = <3300000>;
 198                 regulator-max-microvolt = <3300000>;
 199
 200                 gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>;
 201                 enable-active-high;
 202                 pinctrl-names = "default";
 203                 pinctrl-0 = <&en_pp3300_hub>;
 204
 205                 regulator-always-on;
 206                 regulator-boot-on;
 207
 208                 vin-supply = <&pp3300_a>;
 209         };
 210
 211         /* BOARD-SPECIFIC TOP LEVEL NODES */
 212
 213         backlight: backlight {
 214                 compatible = "pwm-backlight";
 215
 216                 /* The panels don't seem to like anything below ~ 5% */
 217                 brightness-levels = <
 218                         196 256 324 400 484 576 676 784 900 1024 1156 1296
 219                         1444 1600 1764 1936 2116 2304 2500 2704 2916 3136
 220                         3364 3600 3844 4096
 221                 >;
 222                 num-interpolated-steps = <64>;
 223                 default-brightness-level = <951>;
 224
 225                 pwms = <&cros_ec_pwm 1>;
 226                 enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
 227                 power-supply = <&ppvar_sys>;
 228                 pinctrl-names = "default";
 229                 pinctrl-0 = <&ap_edp_bklten>;
 230         };
 231
 232         gpio_keys: gpio-keys {
 233                 compatible = "gpio-keys";
 234                 status = "disabled";
 235                 pinctrl-names = "default";
 236                 pinctrl-0 = <&pen_pdct_l>;
 237
 238                 pen_insert: pen-insert {
 239                         label = "Pen Insert";
 240
 241                         /* Insert = low, eject = high */
 242                         gpios = <&tlmm 52 GPIO_ACTIVE_LOW>;
 243                         linux,code = <SW_PEN_INSERTED>;
 244                         linux,input-type = <EV_SW>;
 245                         wakeup-event-action = <EV_ACT_DEASSERTED>;
 246                         wakeup-source;
 247                 };
 248         };
 249
 250         max98360a: audio-codec-0 {
 251                 compatible = "maxim,max98360a";
 252                 pinctrl-names = "default";
 253                 pinctrl-0 = <&amp_en>;
 254                 sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>;
 255                 #sound-dai-cells = <0>;
 256         };
 257
 258         pwmleds {
 259                 compatible = "pwm-leds";
 260                 keyboard_backlight: keyboard-backlight {
 261                         status = "disabled";
 262                         label = "cros_ec::kbd_backlight";
 263                         pwms = <&cros_ec_pwm 0>;
 264                         max-brightness = <1023>;
 265                 };
 266         };
 267
 268         sound: sound {
 269                 compatible = "google,sc7180-trogdor";
 270                 model = "sc7180-rt5682-max98357a-1mic";
 271
 272                 audio-routing =
 273                         "Headphone Jack", "HPOL",
 274                         "Headphone Jack", "HPOR";
 275
 276                 #sound-dai-cells = <0>;
 277                 #address-cells = <1>;
 278                 #size-cells = <0>;
 279
 280                 dai-link@0 {
 281                         link-name = "MultiMedia0";
 282                         reg = <MI2S_PRIMARY>;
 283                         cpu {
 284                                 sound-dai = <&lpass_cpu MI2S_PRIMARY>;
 285                         };
 286
 287                         sound_multimedia0_codec: codec {
 288                                 sound-dai = <&alc5682 0 /* aif1 */>;
 289                         };
 290                 };
 291
 292                 dai-link@1 {
 293                         link-name = "MultiMedia1";
 294                         reg = <MI2S_SECONDARY>;
 295                         cpu {
 296                                 sound-dai = <&lpass_cpu MI2S_SECONDARY>;
 297                         };
 298
 299                         sound_multimedia1_codec: codec {
 300                                 sound-dai = <&max98360a>;
 301                         };
 302                 };
 303
 304                 dai-link@2 {
 305                         link-name = "MultiMedia2";
 306                         reg = <2>;
 307                         cpu {
 308                                 sound-dai = <&lpass_cpu 2>;
 309                         };
 310
 311                         codec {
 312                                 sound-dai = <&mdss_dp>;
 313                         };
 314                 };
 315         };
 316 };
 317
 318 &qfprom {
 319         vcc-supply = <&pp1800_l11a>;
 320 };
 321
 322 &qspi {
 323         status = "okay";
 324         pinctrl-names = "default";
 325         pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
 326
 327         flash@0 {
 328                 compatible = "jedec,spi-nor";
 329                 reg = <0>;
 330
 331                 spi-max-frequency = <37500000>;
 332                 spi-tx-bus-width = <2>;
 333                 spi-rx-bus-width = <2>;
 334         };
 335 };
 336
 337 &apps_rsc {
 338         pm6150-rpmh-regulators {
 339                 compatible = "qcom,pm6150-rpmh-regulators";
 340                 qcom,pmic-id = "a";
 341
 342                 vddpx_1:
 343                 vdd2:
 344                 pp1125_s1a: smps1 {
 345                         regulator-min-microvolt = <1128000>;
 346                         regulator-max-microvolt = <1128000>;
 347                 };
 348
 349                 vdd_qlink_lv:
 350                 vdd_qlink_lv_ck:
 351                 vdd_qusb_hs0_core:
 352                 vdd_ufs1_core:
 353                 vdda_mipi_csi0_0p9:
 354                 vdda_mipi_csi1_0p9:
 355                 vdda_mipi_csi2_0p9:
 356                 vdda_mipi_csi3_0p9:
 357                 vdda_mipi_dsi0_pll:
 358                 vdda_pll_cc_ebi01:
 359                 vdda_qrefs_0p9:
 360                 vdda_usb_ss_dp_core:
 361                 pp900_l4a: ldo4 {
 362                         regulator-min-microvolt = <824000>;
 363                         regulator-max-microvolt = <928000>;
 364                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 365                 };
 366
 367                 vdd_cx_wlan:
 368                 pp800_l9a: ldo9 {
 369                         regulator-min-microvolt = <488000>;
 370                         regulator-max-microvolt = <800000>;
 371                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 372                 };
 373
 374                 vdd1:
 375                 vddpx_3:
 376                 vddpx_7:
 377                 vio_in:
 378                 pp1800_l10a: ldo10 {
 379                         regulator-min-microvolt = <1800000>;
 380                         regulator-max-microvolt = <1800000>;
 381                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 382                 };
 383
 384                 vdd_qfprom:
 385                 vdda_apc1_cs_1p8:
 386                 vdda_qrefs_1p8:
 387                 vdda_qusb_hs0_1p8:
 388                 vddpx_11:
 389                 vreg_bb_clk:
 390                 pp1800_l11a: ldo11 {
 391                         regulator-min-microvolt = <1800000>;
 392                         regulator-max-microvolt = <1800000>;
 393                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 394                 };
 395
 396                 mcp_vccq:
 397                 pp1800_l12a_r: ldo12 {
 398                         regulator-min-microvolt = <1800000>;
 399                         regulator-max-microvolt = <1800000>;
 400                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 401                 };
 402
 403                 /*
 404                  * On trogdor this needs to match l10a since we use it to
 405                  * give power to things like SPI flash which communicate back
 406                  * on lines powered by l10a.  Thus we force to 1.8V.
 407                  */
 408                 pp1800_l13a: ldo13 {
 409                         regulator-min-microvolt = <1800000>;
 410                         regulator-max-microvolt = <1800000>;
 411                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 412                 };
 413
 414                 pp1800_prox:
 415                 pp1800_l14a: ldo14 {
 416                         regulator-min-microvolt = <1800000>;
 417                         regulator-max-microvolt = <1800000>;
 418                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 419                 };
 420
 421                 pp1800_alc5682:
 422                 pp1800_l15a: ldo15 {
 423                         regulator-min-microvolt = <1800000>;
 424                         regulator-max-microvolt = <1800000>;
 425                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 426                 };
 427
 428                 vdda_qusb_hs0_3p1:
 429                 vdd_pdphy:
 430                 pp3100_l17a: ldo17 {
 431                         regulator-min-microvolt = <2920000>;
 432                         regulator-max-microvolt = <3232000>;
 433                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 434                 };
 435
 436                 pp1800_pen:
 437                 pp1800_l18a: ldo18 {
 438                         regulator-min-microvolt = <1800000>;
 439                         regulator-max-microvolt = <1800000>;
 440                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 441                 };
 442
 443                 mcp_vcc:
 444                 pp2850_l19a: ldo19 {
 445                         regulator-min-microvolt = <2960000>;
 446                         regulator-max-microvolt = <2960000>;
 447                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 448                 };
 449         };
 450
 451         pm6150l-rpmh-regulators {
 452                 compatible = "qcom,pm6150l-rpmh-regulators";
 453                 qcom,pmic-id = "c";
 454
 455                 pp1300_s8c: smps8 {
 456                         regulator-min-microvolt = <1120000>;
 457                         regulator-max-microvolt = <1408000>;
 458                 };
 459
 460                 pp1800_l1c: ldo1 {
 461                         regulator-min-microvolt = <1616000>;
 462                         regulator-max-microvolt = <1984000>;
 463                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 464                 };
 465
 466                 vdd_wcss_adc_dac:
 467                 pp1300_l2c: ldo2 {
 468                         regulator-min-microvolt = <1168000>;
 469                         regulator-max-microvolt = <1304000>;
 470                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 471                 };
 472
 473                 pp1200_brij:
 474                 vdd_ufs1_1p2:
 475                 vdda_csi0_1p25:
 476                 vdda_csi1_1p25:
 477                 vdda_csi2_1p25:
 478                 vdda_csi3_1p25:
 479                 vdda_hv_ebi0:
 480                 vdda_mipi_dsi0_1p2:
 481                 vdda_usb_ss_dp_1p2:
 482                 vddpx_10:
 483                 pp1200_l3c: ldo3 {
 484                         regulator-min-microvolt = <1200000>;
 485                         regulator-max-microvolt = <1200000>;
 486                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 487                 };
 488
 489                 vddpx_2:
 490                 ppvar_l6c: ldo6 {
 491                         regulator-min-microvolt = <1800000>;
 492                         regulator-max-microvolt = <2952000>;
 493                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 494                 };
 495
 496                 pp3300_l7c: ldo7 {
 497                         regulator-min-microvolt = <3304000>;
 498                         regulator-max-microvolt = <3304000>;
 499                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 500                 };
 501
 502                 pp1800_brij_vccio:
 503                 pp1800_edp_vpll:
 504                 pp1800_l8c: ldo8 {
 505                         regulator-min-microvolt = <1800000>;
 506                         regulator-max-microvolt = <1800000>;
 507                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 508                 };
 509
 510                 pp2950_l9c: ldo9 {
 511                         regulator-min-microvolt = <2952000>;
 512                         regulator-max-microvolt = <2952000>;
 513                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 514                 };
 515
 516                 pp3300_l10c: ldo10 {
 517                         regulator-min-microvolt = <3000000>;
 518                         regulator-max-microvolt = <3400000>;
 519                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 520                 };
 521
 522                 pp3300_l11c: ldo11 {
 523                         regulator-min-microvolt = <3000000>;
 524                         regulator-max-microvolt = <3400000>;
 525                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 526                 };
 527
 528                 src_vreg_bob: bob {
 529                         regulator-min-microvolt = <3008000>;
 530                         regulator-max-microvolt = <3960000>;
 531                         regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
 532                 };
 533         };
 534 };
 535
 536 &ap_ec_spi {
 537         status = "okay";
 538         cros_ec: ec@0 {
 539                 compatible = "google,cros-ec-spi";
 540                 reg = <0>;
 541                 interrupt-parent = <&tlmm>;
 542                 interrupts = <94 IRQ_TYPE_LEVEL_LOW>;
 543                 pinctrl-names = "default";
 544                 pinctrl-0 = <&ap_ec_int_l>;
 545                 spi-max-frequency = <3000000>;
 546
 547                 cros_ec_pwm: ec-pwm {
 548                         compatible = "google,cros-ec-pwm";
 549                         #pwm-cells = <1>;
 550                 };
 551
 552                 i2c_tunnel: i2c-tunnel {
 553                         compatible = "google,cros-ec-i2c-tunnel";
 554                         google,remote-bus = <0>;
 555                         #address-cells = <1>;
 556                         #size-cells = <0>;
 557                 };
 558
 559                 typec {
 560                         compatible = "google,cros-ec-typec";
 561                         #address-cells = <1>;
 562                         #size-cells = <0>;
 563
 564                         usb_c0: connector@0 {
 565                                 compatible = "usb-c-connector";
 566                                 reg = <0>;
 567                                 label = "left";
 568                                 power-role = "dual";
 569                                 data-role = "host";
 570                                 try-power-role = "source";
 571                         };
 572
 573                         usb_c1: connector@1 {
 574                                 compatible = "usb-c-connector";
 575                                 reg = <1>;
 576                                 label = "right";
 577                                 power-role = "dual";
 578                                 data-role = "host";
 579                                 try-power-role = "source";
 580                         };
 581                 };
 582         };
 583 };
 584
 585 &ap_h1_spi {
 586         status = "okay";
 587         cr50: tpm@0 {
 588                 compatible = "google,cr50";
 589                 reg = <0>;
 590                 pinctrl-names = "default";
 591                 pinctrl-0 = <&h1_ap_int_odl>;
 592                 spi-max-frequency = <800000>;
 593                 interrupt-parent = <&tlmm>;
 594                 interrupts = <42 IRQ_TYPE_EDGE_RISING>;
 595         };
 596 };
 597
 598 &camcc {
 599         status = "disabled";
 600 };
 601
 602 &dsi0 {
 603         status = "okay";
 604         vdda-supply = <&vdda_mipi_dsi0_1p2>;
 605
 606         ports {
 607                 port@1 {
 608                         endpoint {
 609                                 remote-endpoint = <&sn65dsi86_in>;
 610                                 data-lanes = <0 1 2 3>;
 611                         };
 612                 };
 613         };
 614 };
 615
 616 &dsi_phy {
 617         status = "okay";
 618         vdds-supply = <&vdda_mipi_dsi0_pll>;
 619 };
 620
 621 edp_brij_i2c: &i2c2 {
 622         status = "okay";
 623         clock-frequency = <400000>;
 624
 625         sn65dsi86_bridge: bridge@2d {
 626                 compatible = "ti,sn65dsi86";
 627                 reg = <0x2d>;
 628                 pinctrl-names = "default";
 629                 pinctrl-0 = <&edp_brij_en>, <&edp_brij_irq>;
 630                 gpio-controller;
 631                 #gpio-cells = <2>;
 632
 633                 interrupt-parent = <&tlmm>;
 634                 interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
 635
 636                 enable-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
 637
 638                 vpll-supply = <&pp1800_edp_vpll>;
 639                 vccio-supply = <&pp1800_brij_vccio>;
 640                 vcca-supply = <&pp1200_brij>;
 641                 vcc-supply = <&pp1200_brij>;
 642
 643                 clocks = <&rpmhcc RPMH_LN_BB_CLK3>;
 644                 clock-names = "refclk";
 645
 646                 no-hpd;
 647
 648                 ports {
 649                         #address-cells = <1>;
 650                         #size-cells = <0>;
 651
 652                         port@0 {
 653                                 reg = <0>;
 654                                 sn65dsi86_in: endpoint {
 655                                         remote-endpoint = <&dsi0_out>;
 656                                 };
 657                         };
 658
 659                         port@1 {
 660                                 reg = <1>;
 661                                 sn65dsi86_out: endpoint {
 662                                         data-lanes = <0 1>;
 663                                         remote-endpoint = <&panel_in_edp>;
 664                                 };
 665                         };
 666                 };
 667
 668                 aux-bus {
 669                         panel: panel {
 670                                 /* Compatible will be filled in per-board */
 671                                 power-supply = <&pp3300_dx_edp>;
 672                                 backlight = <&backlight>;
 673                                 hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>;
 674
 675                                 port {
 676                                         panel_in_edp: endpoint {
 677                                                 remote-endpoint = <&sn65dsi86_out>;
 678                                         };
 679                                 };
 680                         };
 681                 };
 682         };
 683 };
 684
 685 ap_sar_sensor_i2c: &i2c5 {
 686         clock-frequency = <400000>;
 687
 688         ap_sar_sensor: proximity@28 {
 689                 compatible = "semtech,sx9310";
 690                 reg = <0x28>;
 691                 #io-channel-cells = <1>;
 692                 pinctrl-names = "default";
 693                 pinctrl-0 = <&p_sensor_int_l>;
 694
 695                 interrupt-parent = <&tlmm>;
 696                 interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
 697
 698                 vdd-supply = <&pp3300_a>;
 699                 svdd-supply = <&pp1800_prox>;
 700
 701                 status = "disabled";
 702                 label = "proximity-wifi";
 703         };
 704 };
 705
 706 ap_tp_i2c: &i2c7 {
 707         status = "okay";
 708         clock-frequency = <400000>;
 709
 710         trackpad: trackpad@15 {
 711                 compatible = "elan,ekth3000";
 712                 reg = <0x15>;
 713                 pinctrl-names = "default";
 714                 pinctrl-0 = <&tp_int_odl>;
 715
 716                 interrupt-parent = <&tlmm>;
 717                 interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
 718
 719                 vcc-supply = <&pp3300_fp_tp>;
 720
 721                 wakeup-source;
 722         };
 723 };
 724
 725 hp_i2c: &i2c9 {
 726         status = "okay";
 727         clock-frequency = <400000>;
 728
 729         alc5682: codec@1a {
 730                 compatible = "realtek,rt5682i";
 731                 reg = <0x1a>;
 732                 pinctrl-names = "default";
 733                 pinctrl-0 = <&hp_irq>;
 734
 735                 #sound-dai-cells = <1>;
 736
 737                 interrupt-parent = <&tlmm>;
 738                 /*
 739                  * This will get ignored because the interrupt type
 740                  * is set in rt5682.c.
 741                  */
 742                 interrupts = <28 IRQ_TYPE_EDGE_BOTH>;
 743
 744                 AVDD-supply = <&pp1800_alc5682>;
 745                 MICVDD-supply = <&pp3300_codec>;
 746                 VBAT-supply = <&pp3300_audio>;
 747
 748                 realtek,dmic1-data-pin = <1>;
 749                 realtek,dmic1-clk-pin = <1>;
 750                 realtek,jd-src = <1>;
 751         };
 752 };
 753
 754 &ipa {
 755         status = "okay";
 756
 757         /*
 758          * Trogdor doesn't have QHEE (Qualcomm's EL2 blob), so the
 759          * modem needs to cover certain init steps (GSI init), and
 760          * the AP needs to wait for it.
 761          */
 762         modem-init;
 763 };
 764
 765 &lpass_cpu {
 766         status = "okay";
 767
 768         pinctrl-names = "default";
 769         pinctrl-0 = <&sec_mi2s_active>, <&pri_mi2s_active>, <&pri_mi2s_mclk_active>;
 770
 771         #address-cells = <1>;
 772         #size-cells = <0>;
 773
 774         mi2s@0 {
 775                 reg = <MI2S_PRIMARY>;
 776                 qcom,playback-sd-lines = <1>;
 777                 qcom,capture-sd-lines = <0>;
 778         };
 779
 780         secondary_mi2s: mi2s@1 {
 781                 reg = <MI2S_SECONDARY>;
 782                 qcom,playback-sd-lines = <0>;
 783         };
 784
 785         hdmi-primary@0 {
 786                 reg = <LPASS_DP_RX>;
 787         };
 788 };
 789
 790 &mdp {
 791         status = "okay";
 792 };
 793
 794 &mdss {
 795         status = "okay";
 796 };
 797
 798 &mdss_dp {
 799         status = "okay";
 800         pinctrl-names = "default";
 801         pinctrl-0 = <&dp_hot_plug_det>;
 802         data-lanes = <0 1>;
 803         vdda-1p2-supply = <&vdda_usb_ss_dp_1p2>;
 804         vdda-0p9-supply = <&vdda_usb_ss_dp_core>;
 805 };
 806
 807 &pm6150_adc {
 808         charger-thermistor@4f {
 809                 reg = <ADC5_AMUX_THM3_100K_PU>;
 810                 qcom,ratiometric;
 811                 qcom,hw-settle-time = <200>;
 812         };
 813 };
 814
 815 &pm6150_adc_tm {
 816         status = "okay";
 817
 818         charger-thermistor@0 {
 819                 reg = <0>;
 820                 io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>;
 821                 qcom,ratiometric;
 822                 qcom,hw-settle-time-us = <200>;
 823         };
 824 };
 825
 826 &pm6150_pon {
 827         status = "disabled";
 828 };
 829
 830 &qupv3_id_0 {
 831         status = "okay";
 832 };
 833
 834 &qupv3_id_1 {
 835         status = "okay";
 836 };
 837
 838 &remoteproc_mpss {
 839         status = "okay";
 840         compatible = "qcom,sc7180-mss-pil";
 841         iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
 842         memory-region = <&mba_mem &mpss_mem>;
 843
 844         /* This gets overridden for SKUs with LTE support. */
 845         firmware-name = "qcom/sc7180-trogdor/modem-nolte/mba.mbn",
 846                         "qcom/sc7180-trogdor/modem-nolte/qdsp6sw.mbn";
 847 };
 848
 849 &sdhc_1 {
 850         status = "okay";
 851
 852         pinctrl-names = "default", "sleep";
 853         pinctrl-0 = <&sdc1_on>;
 854         pinctrl-1 = <&sdc1_off>;
 855         vmmc-supply = <&mcp_vcc>;
 856         vqmmc-supply = <&mcp_vccq>;
 857 };
 858
 859 &sdhc_2 {
 860         pinctrl-names = "default", "sleep";
 861         pinctrl-0 = <&sdc2_on>;
 862         pinctrl-1 = <&sdc2_off>;
 863         vmmc-supply = <&pp2950_l9c>;
 864         vqmmc-supply = <&ppvar_l6c>;
 865
 866         cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
 867 };
 868
 869 &spi0 {
 870         pinctrl-0 = <&qup_spi0_cs_gpio_init_high>, <&qup_spi0_cs_gpio>;
 871         cs-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
 872 };
 873
 874 &spi6 {
 875         pinctrl-0 = <&qup_spi6_cs_gpio_init_high>, <&qup_spi6_cs_gpio>;
 876         cs-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
 877 };
 878
 879 ap_spi_fp: &spi10 {
 880         pinctrl-0 = <&qup_spi10_cs_gpio_init_high>, <&qup_spi10_cs_gpio>;
 881         cs-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
 882
 883         cros_ec_fp: ec@0 {
 884                 compatible = "google,cros-ec-spi";
 885                 reg = <0>;
 886                 interrupt-parent = <&tlmm>;
 887                 interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 888                 pinctrl-names = "default";
 889                 pinctrl-0 = <&fp_to_ap_irq_l>;
 890                 spi-max-frequency = <3000000>;
 891         };
 892 };
 893
 894 #include <arm/cros-ec-keyboard.dtsi>
 895 #include <arm/cros-ec-sbs.dtsi>
 896
 897 &uart3 {
 898         status = "okay";
 899
 900         /delete-property/interrupts;
 901         interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
 902                                 <&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
 903
 904         pinctrl-names = "default", "sleep";
 905         pinctrl-1 = <&qup_uart3_sleep>;
 906
 907         bluetooth: bluetooth {
 908                 compatible = "qcom,wcn3991-bt";
 909                 vddio-supply = <&pp1800_l10a>;
 910                 vddxo-supply = <&pp1800_l1c>;
 911                 vddrf-supply = <&pp1300_l2c>;
 912                 vddch0-supply = <&pp3300_l10c>;
 913                 max-speed = <3200000>;
 914         };
 915 };
 916
 917 &uart8 {
 918         status = "okay";
 919 };
 920
 921 &usb_1 {
 922         status = "okay";
 923 };
 924
 925 &usb_1_dwc3 {
 926         dr_mode = "host";
 927 };
 928
 929 &usb_1_hsphy {
 930         status = "okay";
 931         vdd-supply = <&vdd_qusb_hs0_core>;
 932         vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
 933         vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
 934         qcom,imp-res-offset-value = <8>;
 935         qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>;
 936         qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
 937         qcom,bias-ctrl-value = <0x22>;
 938         qcom,charge-ctrl-value = <3>;
 939         qcom,hsdisc-trim-value = <0>;
 940 };
 941
 942 &usb_1_qmpphy {
 943         status = "okay";
 944         vdda-phy-supply = <&vdda_usb_ss_dp_1p2>;
 945         vdda-pll-supply = <&vdda_usb_ss_dp_core>;
 946 };
 947
 948 &venus {
 949         video-firmware {
 950                 iommus = <&apps_smmu 0x0c42 0x0>;
 951         };
 952 };
 953
 954 &wifi {
 955         status = "okay";
 956         vdd-0.8-cx-mx-supply = <&vdd_cx_wlan>;
 957         vdd-1.8-xo-supply = <&pp1800_l1c>;
 958         vdd-1.3-rfa-supply = <&pp1300_l2c>;
 959         vdd-3.3-ch0-supply = <&pp3300_l10c>;
 960         vdd-3.3-ch1-supply = <&pp3300_l11c>;
 961
 962         wifi-firmware {
 963                 iommus = <&apps_smmu 0xc2 0x1>;
 964         };
 965 };
 966
 967 /* PINCTRL - additions to nodes defined in sc7180.dtsi */
 968
 969 &dp_hot_plug_det {
 970         pinconf {
 971                 pins = "gpio117";
 972                 bias-disable;
 973         };
 974 };
 975
 976 &pri_mi2s_active {
 977         pinconf {
 978                 pins = "gpio53", "gpio54", "gpio55", "gpio56";
 979                 drive-strength = <2>;
 980                 bias-pull-down;
 981         };
 982 };
 983
 984 &pri_mi2s_mclk_active {
 985         pinconf {
 986                 pins = "gpio57";
 987                 drive-strength = <2>;
 988                 bias-pull-down;
 989         };
 990 };
 991
 992 &qspi_cs0 {
 993         pinconf {
 994                 pins = "gpio68";
 995                 bias-disable;
 996         };
 997 };
 998
 999 &qspi_clk {
1000         pinconf {
1001                 pins = "gpio63";
1002                 drive-strength = <8>;
1003                 bias-disable;
1004         };
1005 };
1006
1007 &qspi_data01 {
1008         pinconf {
1009                 pins = "gpio64", "gpio65";
1010
1011                 /* High-Z when no transfers; nice to park the lines */
1012                 bias-pull-up;
1013         };
1014 };
1015
1016 &qup_i2c2_default {
1017         pinconf {
1018                 pins = "gpio15", "gpio16";
1019                 drive-strength = <2>;
1020
1021                 /* Has external pullup */
1022                 bias-disable;
1023         };
1024 };
1025
1026 &qup_i2c4_default {
1027         pinconf {
1028                 pins = "gpio115", "gpio116";
1029                 drive-strength = <2>;
1030
1031                 /* Has external pullup */
1032                 bias-disable;
1033         };
1034 };
1035
1036 &qup_i2c5_default {
1037         pinconf {
1038                 pins = "gpio25", "gpio26";
1039                 drive-strength = <2>;
1040
1041                 /* Has external pullup */
1042                 bias-disable;
1043         };
1044 };
1045
1046 &qup_i2c7_default {
1047         pinconf {
1048                 pins = "gpio6", "gpio7";
1049                 drive-strength = <2>;
1050
1051                 /* Has external pullup */
1052                 bias-disable;
1053         };
1054 };
1055
1056 &qup_i2c9_default {
1057         pinconf {
1058                 pins = "gpio46", "gpio47";
1059                 drive-strength = <2>;
1060
1061                 /* Has external pullup */
1062                 bias-disable;
1063         };
1064 };
1065
1066 &qup_spi0_cs_gpio {
1067         pinconf {
1068                 pins = "gpio34", "gpio35", "gpio36", "gpio37";
1069                 drive-strength = <2>;
1070                 bias-disable;
1071         };
1072 };
1073
1074 &qup_spi6_cs_gpio {
1075         pinconf {
1076                 pins = "gpio59", "gpio60", "gpio61", "gpio62";
1077                 drive-strength = <2>;
1078                 bias-disable;
1079         };
1080 };
1081
1082 &qup_spi10_cs_gpio {
1083         pinconf {
1084                 pins = "gpio86", "gpio87", "gpio88", "gpio89";
1085                 drive-strength = <2>;
1086                 bias-disable;
1087         };
1088 };
1089
1090 &qup_uart3_default {
1091         pinconf-cts {
1092                 /*
1093                  * Configure a pull-down on CTS to match the pull of
1094                  * the Bluetooth module.
1095                  */
1096                 pins = "gpio38";
1097                 bias-pull-down;
1098         };
1099
1100         pinconf-rts-tx {
1101                 /* We'll drive RTS and TX, so no pull */
1102                 pins = "gpio39", "gpio40";
1103                 drive-strength = <2>;
1104                 bias-disable;
1105         };
1106
1107         pinconf-rx {
1108                 /*
1109                  * Configure a pull-up on RX. This is needed to avoid
1110                  * garbage data when the TX pin of the Bluetooth module is
1111                  * in tri-state (module powered off or not driving the
1112                  * signal yet).
1113                  */
1114                 pins = "gpio41";
1115                 bias-pull-up;
1116         };
1117 };
1118
1119 &qup_uart8_default {
1120         pinconf-tx {
1121                 pins = "gpio44";
1122                 drive-strength = <2>;
1123                 bias-disable;
1124         };
1125
1126         pinconf-rx {
1127                 pins = "gpio45";
1128                 drive-strength = <2>;
1129                 bias-pull-up;
1130         };
1131 };
1132
1133 &sec_mi2s_active {
1134         pinconf {
1135                 pins = "gpio49", "gpio50", "gpio51";
1136                 drive-strength = <2>;
1137                 bias-pull-down;
1138         };
1139 };
1140
1141 /* PINCTRL - board-specific pinctrl */
1142
1143 &pm6150_gpio {
1144         status = "disabled"; /* No GPIOs are connected */
1145 };
1146
1147 &pm6150l_gpio {
1148         gpio-line-names = "AP_SUSPEND",
1149                           "",
1150                           "",
1151                           "",
1152                           "",
1153                           "",
1154                           "",
1155                           "",
1156                           "",
1157                           "",
1158                           "",
1159                           "";
1160 };
1161
1162 &tlmm {
1163         /*
1164          * pinctrl settings for pins that have no real owners.
1165          */
1166         pinctrl-names = "default";
1167         pinctrl-0 = <&bios_flash_wp_l>, <&ap_suspend_l_neuter>;
1168
1169         amp_en: amp-en {
1170                 pinmux {
1171                         pins = "gpio23";
1172                         function = "gpio";
1173                 };
1174
1175                 pinconf {
1176                         pins = "gpio23";
1177                         bias-pull-down;
1178                 };
1179         };
1180
1181         ap_ec_int_l: ap-ec-int-l {
1182                 pinmux {
1183                         pins = "gpio94";
1184                         function = "gpio";
1185                         input-enable;
1186                 };
1187
1188                 pinconf {
1189                         pins = "gpio94";
1190                         bias-pull-up;
1191                 };
1192         };
1193
1194         ap_edp_bklten: ap-edp-bklten {
1195                 pinmux {
1196                         pins = "gpio12";
1197                         function = "gpio";
1198                 };
1199
1200                 pinconf {
1201                         pins = "gpio12";
1202                         drive-strength = <2>;
1203                         bias-disable;
1204
1205                         /* Force backlight to be disabled to match state at boot. */
1206                         output-low;
1207                 };
1208         };
1209
1210         ap_suspend_l_neuter: ap-suspend-l-neuter {
1211                 pinmux  {
1212                         pins = "gpio27";
1213                         function = "gpio";
1214                 };
1215
1216                 pinconf {
1217                         pins = "gpio27";
1218                         bias-disable;
1219                 };
1220         };
1221
1222         bios_flash_wp_l: bios-flash-wp-l {
1223                 pinmux {
1224                         pins = "gpio66";
1225                         function = "gpio";
1226                         input-enable;
1227                 };
1228
1229                 pinconf {
1230                         pins = "gpio66";
1231                         bias-disable;
1232                 };
1233         };
1234
1235         edp_brij_en: edp-brij-en {
1236                 pinmux {
1237                         pins = "gpio104";
1238                         function = "gpio";
1239                 };
1240
1241                 pinconf {
1242                         pins = "gpio104";
1243                         drive-strength = <2>;
1244                         bias-disable;
1245                 };
1246         };
1247
1248         edp_brij_irq: edp-brij-irq {
1249                 pinmux {
1250                         pins = "gpio11";
1251                         function = "gpio";
1252                 };
1253
1254                 pinconf {
1255                         pins = "gpio11";
1256                         drive-strength = <2>;
1257                         bias-pull-down;
1258                 };
1259         };
1260
1261         en_pp3300_codec: en-pp3300-codec {
1262                 pinmux {
1263                         pins = "gpio83";
1264                         function = "gpio";
1265                 };
1266
1267                 pinconf {
1268                         pins = "gpio83";
1269                         drive-strength = <2>;
1270                         bias-disable;
1271                 };
1272         };
1273
1274         en_pp3300_dx_edp: en-pp3300-dx-edp {
1275                 pinmux {
1276                         pins = "gpio30";
1277                         function = "gpio";
1278                 };
1279
1280                 pinconf {
1281                         pins = "gpio30";
1282                         drive-strength = <2>;
1283                         bias-disable;
1284                 };
1285         };
1286
1287         en_pp3300_hub: en-pp3300-hub {
1288                 pinmux {
1289                         pins = "gpio84";
1290                         function = "gpio";
1291                 };
1292
1293                 pinconf {
1294                         pins = "gpio84";
1295                         drive-strength = <2>;
1296                         bias-disable;
1297                 };
1298         };
1299
1300         fp_to_ap_irq_l: fp-to-ap-irq-l {
1301                 pinmux {
1302                         pins = "gpio4";
1303                         function = "gpio";
1304                         input-enable;
1305                 };
1306
1307                 pinconf {
1308                         pins = "gpio4";
1309
1310                         /* Has external pullup */
1311                         bias-disable;
1312                 };
1313         };
1314
1315         h1_ap_int_odl: h1-ap-int-odl {
1316                 pinmux {
1317                         pins = "gpio42";
1318                         function = "gpio";
1319                         input-enable;
1320                 };
1321
1322                 pinconf {
1323                         pins = "gpio42";
1324                         bias-pull-up;
1325                 };
1326         };
1327
1328         hp_irq: hp-irq {
1329                 pinmux {
1330                         pins = "gpio28";
1331                         function = "gpio";
1332                 };
1333
1334                 pinconf {
1335                         pins = "gpio28";
1336                         bias-pull-up;
1337                 };
1338         };
1339
1340         pen_irq_l: pen-irq-l {
1341                 pinmux {
1342                         pins = "gpio21";
1343                         function = "gpio";
1344                 };
1345
1346                 pinconf {
1347                         pins = "gpio21";
1348
1349                         /* Has external pullup */
1350                         bias-disable;
1351                 };
1352         };
1353
1354         pen_pdct_l: pen-pdct-l {
1355                 pinmux {
1356                         pins = "gpio52";
1357                         function = "gpio";
1358                 };
1359
1360                 pinconf {
1361                         pins = "gpio52";
1362
1363                         /* Has external pullup */
1364                         bias-disable;
1365                 };
1366         };
1367
1368         pen_rst_odl: pen-rst-odl {
1369                 pinmux  {
1370                         pins = "gpio18";
1371                         function = "gpio";
1372                 };
1373
1374                 pinconf {
1375                         pins = "gpio18";
1376                         bias-disable;
1377                         drive-strength = <2>;
1378
1379                         /*
1380                          * The pen driver doesn't currently support
1381                          * driving this reset line.  By specifying
1382                          * output-high here we're relying on the fact
1383                          * that this pin has a default pulldown at boot
1384                          * (which makes sure the pen was in reset if it
1385                          * was powered) and then we set it high here to
1386                          * take it out of reset.  Better would be if the
1387                          * pen driver could control this and we could
1388                          * remove "output-high" here.
1389                          */
1390                         output-high; /* TODO: Remove this? */
1391                 };
1392         };
1393
1394         p_sensor_int_l: p-sensor-int-l {
1395                 pinmux {
1396                         pins = "gpio24";
1397                         function = "gpio";
1398                         input-enable;
1399                 };
1400
1401                 pinconf {
1402                         pins = "gpio24";
1403                         /* Has external pullup */
1404                         bias-disable;
1405                 };
1406         };
1407
1408         qup_spi0_cs_gpio_init_high: qup-spi0-cs-gpio-init-high {
1409                 pinconf {
1410                         pins = "gpio37";
1411                         output-high;
1412                 };
1413         };
1414
1415         qup_spi6_cs_gpio_init_high: qup-spi6-cs-gpio-init-high {
1416                 pinconf {
1417                         pins = "gpio62";
1418                         output-high;
1419                 };
1420         };
1421
1422         qup_spi10_cs_gpio_init_high: qup-spi10-cs-gpio-init-high {
1423                 pinconf {
1424                         pins = "gpio89";
1425                         output-high;
1426                 };
1427         };
1428
1429         qup_uart3_sleep: qup-uart3-sleep {
1430                 pinmux {
1431                         pins = "gpio38", "gpio39",
1432                                "gpio40", "gpio41";
1433                         function = "gpio";
1434                 };
1435
1436                 pinconf-cts {
1437                         /*
1438                          * Configure a pull-down on CTS to match the pull of
1439                          * the Bluetooth module.
1440                          */
1441                         pins = "gpio38";
1442                         bias-pull-down;
1443                 };
1444
1445                 pinconf-rts {
1446                         /*
1447                          * Configure pull-down on RTS. As RTS is active low
1448                          * signal, pull it low to indicate the BT SoC that it
1449                          * can wakeup the system anytime from suspend state by
1450                          * pulling RX low (by sending wakeup bytes).
1451                          */
1452                          pins = "gpio39";
1453                          bias-pull-down;
1454                 };
1455
1456                 pinconf-tx {
1457                         /*
1458                          * Configure pull-up on TX when it isn't actively driven
1459                          * to prevent BT SoC from receiving garbage during sleep.
1460                          */
1461                         pins = "gpio40";
1462                         bias-pull-up;
1463                 };
1464
1465                 pinconf-rx {
1466                         /*
1467                          * Configure a pull-up on RX. This is needed to avoid
1468                          * garbage data when the TX pin of the Bluetooth module
1469                          * is floating which may cause spurious wakeups.
1470                          */
1471                         pins = "gpio41";
1472                         bias-pull-up;
1473                 };
1474         };
1475
1476         /* Named trackpad_int_1v8_odl on earlier revision schematics */
1477         trackpad_int_1v8_odl:
1478         tp_int_odl: tp-int-odl {
1479                 pinmux {
1480                         pins = "gpio0";
1481                         function = "gpio";
1482                 };
1483
1484                 pinconf {
1485                         pins = "gpio0";
1486
1487                         /* Has external pullup */
1488                         bias-disable;
1489                 };
1490         };
1491
1492         ts_int_l: ts-int-l {
1493                 pinmux  {
1494                         pins = "gpio9";
1495                         function = "gpio";
1496                 };
1497
1498                 pinconf {
1499                         pins = "gpio9";
1500                         bias-pull-up;
1501                 };
1502         };
1503
1504         ts_reset_l: ts-reset-l {
1505                 pinmux  {
1506                         pins = "gpio8";
1507                         function = "gpio";
1508                 };
1509
1510                 pinconf {
1511                         pins = "gpio8";
1512                         bias-disable;
1513                         drive-strength = <2>;
1514                 };
1515         };
1516
1517         sdc1_on: sdc1-on {
1518                 pinconf-clk {
1519                         pins = "sdc1_clk";
1520                         bias-disable;
1521                         drive-strength = <16>;
1522                 };
1523
1524                 pinconf-cmd {
1525                         pins = "sdc1_cmd";
1526                         bias-pull-up;
1527                         drive-strength = <10>;
1528                 };
1529
1530                 pinconf-data {
1531                         pins = "sdc1_data";
1532                         bias-pull-up;
1533                         drive-strength = <10>;
1534                 };
1535
1536                 pinconf-rclk {
1537                         pins = "sdc1_rclk";
1538                         bias-pull-down;
1539                 };
1540         };
1541
1542         sdc1_off: sdc1-off {
1543                 pinconf-clk {
1544                         pins = "sdc1_clk";
1545                         bias-disable;
1546                         drive-strength = <2>;
1547                 };
1548
1549                 pinconf-cmd {
1550                         pins = "sdc1_cmd";
1551                         bias-pull-up;
1552                         drive-strength = <2>;
1553                 };
1554
1555                 pinconf-data {
1556                         pins = "sdc1_data";
1557                         bias-pull-up;
1558                         drive-strength = <2>;
1559                 };
1560
1561                 pinconf-rclk {
1562                         pins = "sdc1_rclk";
1563                         bias-pull-down;
1564                 };
1565         };
1566
1567         sdc2_on: sdc2-on {
1568                 pinconf-clk {
1569                         pins = "sdc2_clk";
1570                         bias-disable;
1571                         drive-strength = <16>;
1572                 };
1573
1574                 pinconf-cmd {
1575                         pins = "sdc2_cmd";
1576                         bias-pull-up;
1577                         drive-strength = <10>;
1578                 };
1579
1580                 pinconf-data {
1581                         pins = "sdc2_data";
1582                         bias-pull-up;
1583                         drive-strength = <10>;
1584                 };
1585
1586                 pinconf-sd-cd {
1587                         pins = "gpio69";
1588                         bias-pull-up;
1589                         drive-strength = <2>;
1590                 };
1591         };
1592
1593         sdc2_off: sdc2-off {
1594                 pinconf-clk {
1595                         pins = "sdc2_clk";
1596                         bias-disable;
1597                         drive-strength = <2>;
1598                 };
1599
1600                 pinconf-cmd {
1601                         pins = "sdc2_cmd";
1602                         bias-pull-up;
1603                         drive-strength = <2>;
1604                 };
1605
1606                 pinconf-data {
1607                         pins = "sdc2_data";
1608                         bias-pull-up;
1609                         drive-strength = <2>;
1610                 };
1611
1612                 pinconf-sd-cd {
1613                         pins = "gpio69";
1614                         bias-pull-up;
1615                         drive-strength = <2>;
1616                 };
1617         };
1618 };