arch/arm64/boot/dts/qcom/pm6150.dtsi

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 // Copyright (c) 2019, The Linux Foundation. All rights reserved.
   3
   4 #include <dt-bindings/iio/qcom,spmi-vadc.h>
   5 #include <dt-bindings/input/linux-event-codes.h>
   6 #include <dt-bindings/interrupt-controller/irq.h>
   7 #include <dt-bindings/spmi/spmi.h>
   8 #include <dt-bindings/thermal/thermal.h>
   9
  10 / {
  11         thermal-zones {
  12                 pm6150_thermal: pm6150-thermal {
  13                         polling-delay-passive = <100>;
  14                         polling-delay = <0>;
  15                         thermal-sensors = <&pm6150_temp>;
  16
  17                         trips {
  18                                 pm6150_trip0: trip0 {
  19                                         temperature = <95000>;
  20                                         hysteresis = <0>;
  21                                         type = "passive";
  22                                 };
  23
  24                                 pm6150_crit: crit {
  25                                         temperature = <115000>;
  26                                         hysteresis = <0>;
  27                                         type = "critical";
  28                                 };
  29                         };
  30                 };
  31         };
  32 };
  33
  34 &spmi_bus {
  35         pm6150_lsid0: pmic@0 {
  36                 compatible = "qcom,pm6150", "qcom,spmi-pmic";
  37                 reg = <0x0 SPMI_USID>;
  38                 #address-cells = <1>;
  39                 #size-cells = <0>;
  40
  41                 pm6150_pon: pon@800 {
  42                         compatible = "qcom,pm8998-pon";
  43                         reg = <0x800>;
  44                         mode-bootloader = <0x2>;
  45                         mode-recovery = <0x1>;
  46
  47                         pm6150_pwrkey: pwrkey {
  48                                 compatible = "qcom,pm8941-pwrkey";
  49                                 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
  50                                 debounce = <15625>;
  51                                 bias-pull-up;
  52                                 linux,code = <KEY_POWER>;
  53                         };
  54                 };
  55
  56                 pm6150_temp: temp-alarm@2400 {
  57                         compatible = "qcom,spmi-temp-alarm";
  58                         reg = <0x2400>;
  59                         interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
  60                         io-channels = <&pm6150_adc ADC5_DIE_TEMP>;
  61                         io-channel-names = "thermal";
  62                         #thermal-sensor-cells = <0>;
  63                 };
  64
  65                 pm6150_adc: adc@3100 {
  66                         compatible = "qcom,spmi-adc5";
  67                         reg = <0x3100>;
  68                         interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
  69                         #address-cells = <1>;
  70                         #size-cells = <0>;
  71                         #io-channel-cells = <1>;
  72
  73                         adc-chan@6 {
  74                                 reg = <ADC5_DIE_TEMP>;
  75                                 label = "die_temp";
  76                         };
  77                 };
  78
  79                 pm6150_adc_tm: adc-tm@3500 {
  80                         compatible = "qcom,spmi-adc-tm5";
  81                         reg = <0x3500>;
  82                         interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
  83                         #thermal-sensor-cells = <1>;
  84                         #address-cells = <1>;
  85                         #size-cells = <0>;
  86                         status = "disabled";
  87                 };
  88
  89                 pm6150_gpio: gpios@c000 {
  90                         compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
  91                         reg = <0xc000>;
  92                         gpio-controller;
  93                         gpio-ranges = <&pm6150_gpio 0 0 10>;
  94                         #gpio-cells = <2>;
  95                         interrupt-controller;
  96                         #interrupt-cells = <2>;
  97                 };
  98         };
  99
 100         pm6150_lsid1: pmic@1 {
 101                 compatible = "qcom,pm6150", "qcom,spmi-pmic";
 102                 reg = <0x1 SPMI_USID>;
 103                 #address-cells = <1>;
 104                 #size-cells = <0>;
 105         };
 106 };