arch/arm/boot/dts/qcom-ipq8064-rb3011.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 #include "qcom-ipq8064.dtsi"
   3 #include <dt-bindings/input/input.h>
   4
   5 / {
   6         model = "MikroTik RB3011UiAS-RM";
   7         compatible = "mikrotik,rb3011";
   8
   9         aliases {
  10                 serial0 = &gsbi7_serial;
  11                 ethernet0 = &gmac0;
  12                 ethernet1 = &gmac3;
  13                 mdio-gpio0 = &mdio0;
  14                 mdio-gpio1 = &mdio1;
  15         };
  16
  17         chosen {
  18                 bootargs = "loglevel=8 console=ttyMSM0,115200";
  19                 stdout-path = "serial0:115200n8";
  20         };
  21
  22         memory@0 {
  23                 reg = <0x42000000 0x3e000000>;
  24                 device_type = "memory";
  25         };
  26
  27         mdio0: mdio@0 {
  28                 status = "okay";
  29                 compatible = "virtual,mdio-gpio";
  30                 gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
  31                         <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
  32                 #address-cells = <1>;
  33                 #size-cells = <0>;
  34
  35                 pinctrl-0 = <&mdio0_pins>;
  36                 pinctrl-names = "default";
  37
  38                 switch0: switch@10 {
  39                         compatible = "qca,qca8337";
  40                         #address-cells = <1>;
  41                         #size-cells = <0>;
  42
  43                         dsa,member = <0 0>;
  44
  45                         pinctrl-0 = <&sw0_reset_pin>;
  46                         pinctrl-names = "default";
  47
  48                         reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
  49                         reg = <0x10>;
  50
  51                         ports {
  52                                 #address-cells = <1>;
  53                                 #size-cells = <0>;
  54
  55                                 switch0cpu: port@0 {
  56                                         reg = <0>;
  57                                         label = "cpu";
  58                                         ethernet = <&gmac0>;
  59                                         phy-mode = "rgmii-id";
  60                                         fixed-link {
  61                                                 speed = <1000>;
  62                                                 full-duplex;
  63                                         };
  64                                 };
  65
  66                                 port@1 {
  67                                         reg = <1>;
  68                                         label = "sw1";
  69                                 };
  70
  71                                 port@2 {
  72                                         reg = <2>;
  73                                         label = "sw2";
  74                                 };
  75
  76                                 port@3 {
  77                                         reg = <3>;
  78                                         label = "sw3";
  79                                 };
  80
  81                                 port@4 {
  82                                         reg = <4>;
  83                                         label = "sw4";
  84                                 };
  85
  86                                 port@5 {
  87                                         reg = <5>;
  88                                         label = "sw5";
  89                                 };
  90                         };
  91                 };
  92         };
  93
  94         mdio1: mdio@1 {
  95                 status = "okay";
  96                 compatible = "virtual,mdio-gpio";
  97                 gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>,
  98                         <&qcom_pinmux 10 GPIO_ACTIVE_HIGH>;
  99                 #address-cells = <1>;
 100                 #size-cells = <0>;
 101
 102                 pinctrl-0 = <&mdio1_pins>;
 103                 pinctrl-names = "default";
 104
 105                 switch1: switch@14 {
 106                         compatible = "qca,qca8337";
 107                         #address-cells = <1>;
 108                         #size-cells = <0>;
 109
 110                         dsa,member = <1 0>;
 111
 112                         pinctrl-0 = <&sw1_reset_pin>;
 113                         pinctrl-names = "default";
 114
 115                         reset-gpios = <&qcom_pinmux 17 GPIO_ACTIVE_LOW>;
 116                         reg = <0x10>;
 117
 118                         ports {
 119                                 #address-cells = <1>;
 120                                 #size-cells = <0>;
 121
 122                                 switch1cpu: port@0 {
 123                                         reg = <0>;
 124                                         label = "cpu";
 125                                         ethernet = <&gmac3>;
 126                                         phy-mode = "sgmii";
 127                                         fixed-link {
 128                                                 speed = <1000>;
 129                                                 full-duplex;
 130                                         };
 131                                 };
 132
 133                                 port@1 {
 134                                         reg = <1>;
 135                                         label = "sw6";
 136                                 };
 137
 138                                 port@2 {
 139                                         reg = <2>;
 140                                         label = "sw7";
 141                                 };
 142
 143                                 port@3 {
 144                                         reg = <3>;
 145                                         label = "sw8";
 146                                 };
 147
 148                                 port@4 {
 149                                         reg = <4>;
 150                                         label = "sw9";
 151                                 };
 152
 153                                 port@5 {
 154                                         reg = <5>;
 155                                         label = "sw10";
 156                                 };
 157                         };
 158                 };
 159         };
 160
 161         soc {
 162                 gsbi5: gsbi@1a200000 {
 163                         qcom,mode = <GSBI_PROT_SPI>;
 164                         status = "okay";
 165
 166                         spi4: spi@1a280000 {
 167                                 status = "okay";
 168                                 spi-max-frequency = <50000000>;
 169
 170                                 pinctrl-0 = <&spi_pins>;
 171                                 pinctrl-names = "default";
 172
 173                                 cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
 174
 175                                 norflash: s25fl016k@0 {
 176                                         compatible = "jedec,spi-nor";
 177                                         #address-cells = <1>;
 178                                         #size-cells = <1>;
 179                                         spi-max-frequency = <50000000>;
 180                                         reg = <0>;
 181
 182                                         partition@0 {
 183                                                 label = "RouterBoot";
 184                                                 reg = <0x0 0x40000>;
 185                                         };
 186                                 };
 187                         };
 188                 };
 189
 190                 gpio_keys {
 191                         compatible = "gpio-keys";
 192                         pinctrl-0 = <&buttons_pins>;
 193                         pinctrl-names = "default";
 194
 195                         button@1 {
 196                                 label = "reset";
 197                                 linux,code = <KEY_RESTART>;
 198                                 gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
 199                                 linux,input-type = <1>;
 200                                 debounce-interval = <60>;
 201                         };
 202                 };
 203
 204                 leds {
 205                         compatible = "gpio-leds";
 206                         pinctrl-0 = <&leds_pins>;
 207                         pinctrl-names = "default";
 208
 209                         led@7 {
 210                                 label = "rb3011:green:user";
 211                                 gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
 212                                 default-state = "off";
 213                         };
 214                 };
 215
 216         };
 217 };
 218
 219 &adm_dma {
 220         status = "okay";
 221 };
 222
 223 &gmac0 {
 224         status = "okay";
 225
 226         phy-mode = "rgmii";
 227         qcom,id = <0>;
 228         phy-handle = <&switch0cpu>;
 229
 230         fixed-link {
 231                 speed = <1000>;
 232                 full-duplex;
 233         };
 234 };
 235
 236 &gmac3 {
 237         status = "okay";
 238
 239         phy-mode = "sgmii";
 240         qcom,id = <3>;
 241         phy-handle = <&switch1cpu>;
 242
 243         fixed-link {
 244                 speed = <1000>;
 245                 full-duplex;
 246         };
 247 };
 248
 249 &gsbi7 {
 250         status = "okay";
 251         qcom,mode = <GSBI_PROT_I2C_UART>;
 252 };
 253
 254 &gsbi7_serial {
 255         status = "okay";
 256 };
 257
 258 &hs_phy_1 {
 259         status = "okay";
 260 };
 261
 262 &nand {
 263         status = "okay";
 264
 265         nandcs@0 {
 266                 compatible = "qcom,nandcs";
 267                 reg = <0>;
 268
 269                 nand-ecc-strength = <4>;
 270                 nand-bus-width = <8>;
 271                 nand-ecc-step-size = <512>;
 272
 273                 partitions {
 274                         compatible = "fixed-partitions";
 275                         #address-cells = <1>;
 276                         #size-cells = <1>;
 277
 278                         boot@0 {
 279                                 label = "RouterBoard NAND 1 Boot";
 280                                 reg = <0x0000000 0x0800000>;
 281                         };
 282
 283                         main@800000 {
 284                                 label = "RouterBoard NAND 1 Main";
 285                                 reg = <0x0800000 0x7800000>;
 286                         };
 287                 };
 288         };
 289 };
 290
 291 &qcom_pinmux {
 292         buttons_pins: buttons_pins {
 293                 mux {
 294                         pins = "gpio66";
 295                         drive-strength = <16>;
 296                         bias-disable;
 297                 };
 298         };
 299
 300         leds_pins: leds_pins {
 301                 mux {
 302                         pins = "gpio33";
 303                         drive-strength = <16>;
 304                         bias-disable;
 305                 };
 306         };
 307
 308         mdio0_pins: mdio0_pins {
 309                 mux {
 310                         pins = "gpio0", "gpio1";
 311                         function = "gpio";
 312                         drive-strength = <8>;
 313                         bias-disable;
 314                 };
 315         };
 316
 317         mdio1_pins: mdio1_pins {
 318                 mux {
 319                         pins = "gpio10", "gpio11";
 320                         function = "gpio";
 321                         drive-strength = <8>;
 322                         bias-disable;
 323                 };
 324         };
 325
 326         sw0_reset_pin: sw0_reset_pin {
 327                 mux {
 328                         pins = "gpio16";
 329                         drive-strength = <16>;
 330                         function = "gpio";
 331                         bias-disable;
 332                         input-disable;
 333                 };
 334         };
 335
 336         sw1_reset_pin: sw1_reset_pin {
 337                 mux {
 338                         pins = "gpio17";
 339                         drive-strength = <16>;
 340                         function = "gpio";
 341                         bias-disable;
 342                         input-disable;
 343                 };
 344         };
 345
 346         usb1_pwr_en_pins: usb1_pwr_en_pins {
 347                 mux {
 348                         pins = "gpio4";
 349                         function = "gpio";
 350                         drive-strength = <16>;
 351                         bias-disable;
 352                         output-high;
 353                 };
 354         };
 355 };
 356
 357 &ss_phy_1 {
 358         status = "okay";
 359 };
 360
 361 &usb3_1 {
 362         pinctrl-0 = <&usb1_pwr_en_pins>;
 363         pinctrl-names = "default";
 364
 365         status = "okay";
 366 };