arch/arm/boot/dts/imx6dl-yapp4-common.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 //
   3 // Copyright (C) 2015-2018 Y Soft Corporation, a.s.
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/interrupt-controller/irq.h>
   7 #include <dt-bindings/input/input.h>
   8 #include <dt-bindings/pwm/pwm.h>
   9
  10 / {
  11         aliases: aliases {
  12                 ethernet1 = &eth1;
  13                 ethernet2 = &eth2;
  14         };
  15
  16         backlight: backlight {
  17                 compatible = "pwm-backlight";
  18                 pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
  19                 brightness-levels = <0 32 64 128 255>;
  20                 default-brightness-level = <32>;
  21                 num-interpolated-steps = <8>;
  22                 power-supply = <&sw2_reg>;
  23                 status = "disabled";
  24         };
  25
  26         lcd_display: display {
  27                 compatible = "fsl,imx-parallel-display";
  28                 #address-cells = <1>;
  29                 #size-cells = <0>;
  30                 interface-pix-fmt = "rgb24";
  31                 pinctrl-names = "default";
  32                 pinctrl-0 = <&pinctrl_ipu1>;
  33                 status = "disabled";
  34
  35                 port@0 {
  36                         reg = <0>;
  37
  38                         lcd_display_in: endpoint {
  39                                 remote-endpoint = <&ipu1_di0_disp0>;
  40                         };
  41                 };
  42
  43                 port@1 {
  44                         reg = <1>;
  45
  46                         lcd_display_out: endpoint {
  47                                 remote-endpoint = <&lcd_panel_in>;
  48                         };
  49                 };
  50         };
  51
  52         panel: panel {
  53                 compatible = "dataimage,scf0700c48ggu18";
  54                 power-supply = <&sw2_reg>;
  55                 status = "disabled";
  56
  57                 port {
  58                         lcd_panel_in: endpoint {
  59                                 remote-endpoint = <&lcd_display_out>;
  60                         };
  61                 };
  62         };
  63
  64         reg_pcie: regulator-pcie {
  65                 compatible = "regulator-fixed";
  66                 pinctrl-names = "default";
  67                 pinctrl-0 = <&pinctrl_pcie_reg>;
  68                 regulator-name = "MPCIE_3V3";
  69                 regulator-min-microvolt = <3300000>;
  70                 regulator-max-microvolt = <3300000>;
  71                 gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
  72                 enable-active-high;
  73                 status = "disabled";
  74         };
  75
  76         reg_usb_h1_vbus: regulator-usb-h1-vbus {
  77                 compatible = "regulator-fixed";
  78                 pinctrl-names = "default";
  79                 pinctrl-0 = <&pinctrl_usbh1_vbus>;
  80                 regulator-name = "usb_h1_vbus";
  81                 regulator-min-microvolt = <5000000>;
  82                 regulator-max-microvolt = <5000000>;
  83                 gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
  84                 enable-active-high;
  85                 status = "disabled";
  86         };
  87
  88         reg_usb_otg_vbus: regulator-usb-otg-vbus {
  89                 compatible = "regulator-fixed";
  90                 pinctrl-names = "default";
  91                 pinctrl-0 = <&pinctrl_usbotg_vbus>;
  92                 regulator-name = "usb_otg_vbus";
  93                 regulator-min-microvolt = <5000000>;
  94                 regulator-max-microvolt = <5000000>;
  95                 gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
  96                 enable-active-high;
  97                 status = "okay";
  98         };
  99 };
 100
 101 &fec {
 102         pinctrl-names = "default";
 103         pinctrl-0 = <&pinctrl_enet>;
 104         phy-mode = "rgmii-id";
 105         phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 106         phy-reset-duration = <20>;
 107         phy-supply = <&sw2_reg>;
 108         status = "okay";
 109
 110         fixed-link {
 111                 speed = <1000>;
 112                 full-duplex;
 113         };
 114
 115         mdio {
 116                 #address-cells = <1>;
 117                 #size-cells = <0>;
 118
 119                 phy_port2: phy@1 {
 120                         reg = <1>;
 121                 };
 122
 123                 phy_port3: phy@2 {
 124                         reg = <2>;
 125                 };
 126
 127                 switch@10 {
 128                         compatible = "qca,qca8334";
 129                         reg = <10>;
 130
 131                         switch_ports: ports {
 132                                 #address-cells = <1>;
 133                                 #size-cells = <0>;
 134
 135                                 ethphy0: port@0 {
 136                                         reg = <0>;
 137                                         label = "cpu";
 138                                         phy-mode = "rgmii-id";
 139                                         ethernet = <&fec>;
 140
 141                                         fixed-link {
 142                                                 speed = <1000>;
 143                                                 full-duplex;
 144                                         };
 145                                 };
 146
 147                                 eth2: port@2 {
 148                                         reg = <2>;
 149                                         label = "eth2";
 150                                         phy-handle = <&phy_port2>;
 151                                 };
 152
 153                                 eth1: port@3 {
 154                                         reg = <3>;
 155                                         label = "eth1";
 156                                         phy-handle = <&phy_port3>;
 157                                 };
 158                         };
 159                 };
 160         };
 161 };
 162
 163 &hdmi {
 164         pinctrl-names = "default";
 165         pinctrl-0 = <&pinctrl_hdmi_cec>;
 166         ddc-i2c-bus = <&i2c2>;
 167         status = "disabled";
 168 };
 169
 170 &i2c2 {
 171         clock-frequency = <100000>;
 172         pinctrl-names = "default";
 173         pinctrl-0 = <&pinctrl_i2c2>;
 174         status = "okay";
 175
 176         pmic@8 {
 177                 compatible = "fsl,pfuze200";
 178                 pinctrl-names = "default";
 179                 pinctrl-0 = <&pinctrl_pmic>;
 180                 reg = <0x8>;
 181
 182                 regulators {
 183                         sw1a_reg: sw1ab {
 184                                 regulator-min-microvolt = <300000>;
 185                                 regulator-max-microvolt = <1875000>;
 186                                 regulator-boot-on;
 187                                 regulator-always-on;
 188                                 regulator-ramp-delay = <6250>;
 189                         };
 190
 191                         sw2_reg: sw2 {
 192                                 regulator-min-microvolt = <800000>;
 193                                 regulator-max-microvolt = <3300000>;
 194                                 regulator-boot-on;
 195                                 regulator-always-on;
 196                         };
 197
 198                         sw3a_reg: sw3a {
 199                                 regulator-min-microvolt = <400000>;
 200                                 regulator-max-microvolt = <1975000>;
 201                                 regulator-boot-on;
 202                                 regulator-always-on;
 203                         };
 204
 205                         sw3b_reg: sw3b {
 206                                 regulator-min-microvolt = <400000>;
 207                                 regulator-max-microvolt = <1975000>;
 208                                 regulator-boot-on;
 209                                 regulator-always-on;
 210                         };
 211
 212                         swbst_reg: swbst {
 213                                 regulator-min-microvolt = <5000000>;
 214                                 regulator-max-microvolt = <5150000>;
 215                         };
 216
 217                         vgen1_reg: vgen1 {
 218                                 regulator-min-microvolt = <800000>;
 219                                 regulator-max-microvolt = <1550000>;
 220                         };
 221
 222                         vgen2_reg: vgen2 {
 223                                 regulator-min-microvolt = <800000>;
 224                                 regulator-max-microvolt = <1550000>;
 225                         };
 226
 227                         vgen3_reg: vgen3 {
 228                                 regulator-min-microvolt = <1800000>;
 229                                 regulator-max-microvolt = <3300000>;
 230                                 regulator-always-on;
 231                         };
 232
 233                         vgen4_reg: vgen4 {
 234                                 regulator-min-microvolt = <1800000>;
 235                                 regulator-max-microvolt = <3300000>;
 236                                 regulator-always-on;
 237                         };
 238
 239                         vgen5_reg: vgen5 {
 240                                 regulator-min-microvolt = <1800000>;
 241                                 regulator-max-microvolt = <3300000>;
 242                                 regulator-always-on;
 243                         };
 244
 245                         vgen6_reg: vgen6 {
 246                                 regulator-min-microvolt = <1800000>;
 247                                 regulator-max-microvolt = <3300000>;
 248                                 regulator-always-on;
 249                         };
 250
 251                         vref_reg: vrefddr {
 252                                 regulator-boot-on;
 253                                 regulator-always-on;
 254                         };
 255
 256                         vsnvs_reg: vsnvs {
 257                                 regulator-min-microvolt = <1000000>;
 258                                 regulator-max-microvolt = <3000000>;
 259                                 regulator-boot-on;
 260                                 regulator-always-on;
 261                         };
 262                 };
 263         };
 264
 265         leds: led-controller@30 {
 266                 compatible = "ti,lp5562";
 267                 reg = <0x30>;
 268                 clock-mode = /bits/ 8 <1>;
 269                 status = "disabled";
 270                 #address-cells = <1>;
 271                 #size-cells = <0>;
 272
 273                 chan@0 {
 274                         chan-name = "R";
 275                         led-cur = /bits/ 8 <0x20>;
 276                         max-cur = /bits/ 8 <0x60>;
 277                         reg = <0>;
 278                 };
 279
 280                 chan@1 {
 281                         chan-name = "G";
 282                         led-cur = /bits/ 8 <0x20>;
 283                         max-cur = /bits/ 8 <0x60>;
 284                         reg = <1>;
 285                 };
 286
 287                 chan@2 {
 288                         chan-name = "B";
 289                         led-cur = /bits/ 8 <0x20>;
 290                         max-cur = /bits/ 8 <0x60>;
 291                         reg = <2>;
 292                 };
 293
 294                 chan@3 {
 295                         chan-name = "W";
 296                         led-cur = /bits/ 8 <0x0>;
 297                         max-cur = /bits/ 8 <0x0>;
 298                         reg = <3>;
 299                 };
 300         };
 301
 302         eeprom@57 {
 303                 compatible = "atmel,24c128";
 304                 reg = <0x57>;
 305                 pagesize = <64>;
 306                 status = "okay";
 307         };
 308
 309         touchscreen: touchscreen@5c {
 310                 compatible = "pixcir,pixcir_tangoc";
 311                 reg = <0x5c>;
 312                 pinctrl-0 = <&pinctrl_touch>;
 313                 interrupt-parent = <&gpio4>;
 314                 interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
 315                 attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
 316                 reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 317                 touchscreen-size-x = <800>;
 318                 touchscreen-size-y = <480>;
 319                 status = "disabled";
 320         };
 321 };
 322
 323 &i2c3 {
 324         clock-frequency = <100000>;
 325         pinctrl-names = "default";
 326         pinctrl-0 = <&pinctrl_i2c3>;
 327         status = "okay";
 328
 329         oled_1309: oled@3c {
 330                 compatible = "solomon,ssd1309fb-i2c";
 331                 reg = <0x3c>;
 332                 solomon,height = <64>;
 333                 solomon,width = <128>;
 334                 solomon,page-offset = <0>;
 335                 solomon,segment-no-remap;
 336                 solomon,prechargep2 = <15>;
 337                 reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
 338                 vbat-supply = <&sw2_reg>;
 339                 status = "disabled";
 340         };
 341
 342         oled_1305: oled@3d {
 343                 compatible = "solomon,ssd1305fb-i2c";
 344                 reg = <0x3d>;
 345                 solomon,height = <64>;
 346                 solomon,width = <128>;
 347                 solomon,page-offset = <0>;
 348                 solomon,prechargep2 = <15>;
 349                 reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
 350                 vbat-supply = <&sw2_reg>;
 351                 status = "disabled";
 352         };
 353
 354         gpio_oled: gpio@41 {
 355                 compatible = "nxp,pca9536";
 356                 gpio-controller;
 357                 #gpio-cells = <2>;
 358                 reg = <0x41>;
 359                 vcc-supply = <&sw2_reg>;
 360                 status = "disabled";
 361         };
 362
 363         touchkeys: keys@5a {
 364                 compatible = "fsl,mpr121-touchkey";
 365                 reg = <0x5a>;
 366                 vdd-supply = <&sw2_reg>;
 367                 autorepeat;
 368                 linux,keycodes = <KEY_1>, <KEY_2>, <KEY_3>, <KEY_4>, <KEY_5>,
 369                                 <KEY_6>, <KEY_7>, <KEY_8>, <KEY_9>,
 370                                 <KEY_BACKSPACE>, <KEY_0>, <KEY_ENTER>;
 371                 poll-interval = <50>;
 372                 status = "disabled";
 373         };
 374 };
 375
 376 &iomuxc {
 377         pinctrl_enet: enetgrp {
 378                 fsl,pins = <
 379                         MX6QDL_PAD_ENET_MDIO__ENET_MDIO         0x1b020
 380                         MX6QDL_PAD_ENET_MDC__ENET_MDC           0x1b020
 381                         MX6QDL_PAD_RGMII_TXC__RGMII_TXC         0x1b020
 382                         MX6QDL_PAD_RGMII_TD0__RGMII_TD0         0x1b020
 383                         MX6QDL_PAD_RGMII_TD1__RGMII_TD1         0x1b020
 384                         MX6QDL_PAD_RGMII_TD2__RGMII_TD2         0x1b020
 385                         MX6QDL_PAD_RGMII_TD3__RGMII_TD3         0x1b020
 386                         MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL   0x1b020
 387                         MX6QDL_PAD_RGMII_RXC__RGMII_RXC         0x1b020
 388                         MX6QDL_PAD_RGMII_RD0__RGMII_RD0         0x1b020
 389                         MX6QDL_PAD_RGMII_RD1__RGMII_RD1         0x1b020
 390                         MX6QDL_PAD_RGMII_RD2__RGMII_RD2         0x1b020
 391                         MX6QDL_PAD_RGMII_RD3__RGMII_RD3         0x1b020
 392                         MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL   0x1b020
 393                         MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK    0x1b010
 394                         MX6QDL_PAD_GPIO_16__ENET_REF_CLK        0x1b010
 395                         MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25      0x1b098
 396                 >;
 397         };
 398
 399         pinctrl_hdmi_cec: hdmicecgrp {
 400                 fsl,pins = <
 401                         MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE    0x1b898
 402                 >;
 403         };
 404
 405         pinctrl_i2c2: i2c2grp {
 406                 fsl,pins = <
 407                         MX6QDL_PAD_KEY_COL3__I2C2_SCL   0x4001b899
 408                         MX6QDL_PAD_KEY_ROW3__I2C2_SDA   0x4001b899
 409                 >;
 410         };
 411
 412         pinctrl_i2c3: i2c3grp {
 413                 fsl,pins = <
 414                         MX6QDL_PAD_GPIO_3__I2C3_SCL     0x4001b899
 415                         MX6QDL_PAD_GPIO_6__I2C3_SDA     0x4001b899
 416                 >;
 417         };
 418
 419         pinctrl_ipu1: ipu1grp {
 420                 fsl,pins = <
 421                         MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK      0x10
 422                         MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02             0x10
 423                         MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03             0x10
 424                         MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00        0x10
 425                         MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01        0x10
 426                         MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02        0x10
 427                         MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03        0x10
 428                         MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04        0x10
 429                         MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05        0x10
 430                         MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06        0x10
 431                         MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07        0x10
 432                         MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08        0x10
 433                         MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09        0x10
 434                         MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10       0x10
 435                         MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11       0x10
 436                         MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12       0x10
 437                         MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13       0x10
 438                         MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14       0x10
 439                         MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15       0x10
 440                         MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16       0x10
 441                         MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17       0x10
 442                         MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18       0x10
 443                         MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19       0x10
 444                         MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20       0x10
 445                         MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21       0x10
 446                         MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22       0x10
 447                         MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23       0x10
 448                 >;
 449         };
 450
 451         pinctrl_pcie: pciegrp {
 452                 fsl,pins = <
 453                         MX6QDL_PAD_GPIO_17__GPIO7_IO12          0x1b098
 454                         MX6QDL_PAD_KEY_COL4__GPIO4_IO14         0x1b098
 455                         MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20     0x1b098
 456                 >;
 457         };
 458
 459         pinctrl_pcie_reg: pciereggrp {
 460                 fsl,pins = <
 461                         MX6QDL_PAD_EIM_D19__GPIO3_IO19  0x1b098
 462                 >;
 463         };
 464
 465         pinctrl_pmic: pmicgrp {
 466                 fsl,pins = <
 467                         MX6QDL_PAD_GPIO_18__GPIO7_IO13  0x1b098
 468                 >;
 469         };
 470
 471         pinctrl_pwm1: pwm1grp {
 472                 fsl,pins = <
 473                         MX6QDL_PAD_GPIO_9__PWM1_OUT     0x8
 474                 >;
 475         };
 476
 477         pinctrl_touch: touchgrp {
 478                 fsl,pins = <
 479                         MX6QDL_PAD_GPIO_19__GPIO4_IO05  0x1b098
 480                         MX6QDL_PAD_GPIO_2__GPIO1_IO02   0x1b098
 481                 >;
 482         };
 483
 484         pinctrl_uart1: uart1grp {
 485                 fsl,pins = <
 486                         MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA    0x1b0a8
 487                         MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA    0x1b0a8
 488                 >;
 489         };
 490
 491         pinctrl_uart2: uart2grp {
 492                 fsl,pins = <
 493                         MX6QDL_PAD_GPIO_7__UART2_TX_DATA        0x1b098
 494                         MX6QDL_PAD_GPIO_8__UART2_RX_DATA        0x1b098
 495                 >;
 496         };
 497
 498         pinctrl_usbh1: usbh1grp {
 499                 fsl,pins = <
 500                         MX6QDL_PAD_EIM_D30__USB_H1_OC   0x1b098
 501                 >;
 502         };
 503
 504         pinctrl_usbh1_vbus: usbh1-vbus {
 505                 fsl,pins = <
 506                         MX6QDL_PAD_ENET_TXD1__GPIO1_IO29        0x98
 507                 >;
 508         };
 509
 510         pinctrl_usbotg: usbotggrp {
 511                 fsl,pins = <
 512                         MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID       0x1b098
 513                         MX6QDL_PAD_EIM_D21__USB_OTG_OC          0x1b098
 514                 >;
 515         };
 516
 517         pinctrl_usbotg_vbus: usbotg-vbus {
 518                 fsl,pins = <
 519                         MX6QDL_PAD_EIM_D22__GPIO3_IO22  0x98
 520                 >;
 521         };
 522
 523         pinctrl_usdhc3: usdhc3grp {
 524                 fsl,pins = <
 525                         MX6QDL_PAD_EIM_A16__GPIO2_IO22  0x1b018
 526                         MX6QDL_PAD_SD3_RST__GPIO7_IO08  0x1b018
 527                         MX6QDL_PAD_SD3_CMD__SD3_CMD     0x17059
 528                         MX6QDL_PAD_SD3_CLK__SD3_CLK     0x10059
 529                         MX6QDL_PAD_SD3_DAT0__SD3_DATA0  0x17059
 530                         MX6QDL_PAD_SD3_DAT1__SD3_DATA1  0x17059
 531                         MX6QDL_PAD_SD3_DAT2__SD3_DATA2  0x17059
 532                         MX6QDL_PAD_SD3_DAT3__SD3_DATA3  0x17059
 533                 >;
 534         };
 535
 536         pinctrl_usdhc4: usdhc4grp {
 537                 fsl,pins = <
 538                         MX6QDL_PAD_SD4_CMD__SD4_CMD     0x1f069
 539                         MX6QDL_PAD_SD4_CLK__SD4_CLK     0x10069
 540                         MX6QDL_PAD_SD4_DAT0__SD4_DATA0  0x17069
 541                         MX6QDL_PAD_SD4_DAT1__SD4_DATA1  0x17069
 542                         MX6QDL_PAD_SD4_DAT2__SD4_DATA2  0x17069
 543                         MX6QDL_PAD_SD4_DAT3__SD4_DATA3  0x17069
 544                         MX6QDL_PAD_SD4_DAT4__SD4_DATA4  0x17069
 545                         MX6QDL_PAD_SD4_DAT5__SD4_DATA5  0x17069
 546                         MX6QDL_PAD_SD4_DAT6__SD4_DATA6  0x17069
 547                         MX6QDL_PAD_SD4_DAT7__SD4_DATA7  0x17069
 548                 >;
 549         };
 550
 551         pinctrl_wdog: wdoggrp {
 552                 fsl,pins = <
 553                         MX6QDL_PAD_GPIO_1__WDOG2_B      0x1b0b0
 554                 >;
 555         };
 556 };
 557
 558 &ipu1_di0_disp0 {
 559         remote-endpoint = <&lcd_display_in>;
 560 };
 561
 562 &pcie {
 563         pinctrl-names = "default";
 564         pinctrl-0 = <&pinctrl_pcie>;
 565         reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
 566         vpcie-supply = <&reg_pcie>;
 567         status = "disabled";
 568 };
 569
 570 &pwm1 {
 571         pinctrl-names = "default";
 572         pinctrl-0 = <&pinctrl_pwm1>;
 573         status = "disabled";
 574 };
 575
 576 &uart1 {
 577         pinctrl-names = "default";
 578         pinctrl-0 = <&pinctrl_uart1>;
 579         status = "okay";
 580 };
 581
 582 &uart2 {
 583         pinctrl-names = "default";
 584         pinctrl-0 = <&pinctrl_uart2>;
 585         status = "okay";
 586 };
 587
 588 &usbh1 {
 589         pinctrl-names = "default";
 590         pinctrl-0 = <&pinctrl_usbh1>;
 591         vbus-supply = <&reg_usb_h1_vbus>;
 592         over-current-active-low;
 593         status = "disabled";
 594 };
 595
 596 &usbotg {
 597         pinctrl-names = "default";
 598         pinctrl-0 = <&pinctrl_usbotg>;
 599         vbus-supply = <&reg_usb_otg_vbus>;
 600         over-current-active-low;
 601         srp-disable;
 602         hnp-disable;
 603         adp-disable;
 604         status = "okay";
 605 };
 606
 607 &usbphy1 {
 608         fsl,tx-d-cal = <106>;
 609         status = "okay";
 610 };
 611
 612 &usbphy2 {
 613         fsl,tx-d-cal = <109>;
 614         status = "disabled";
 615 };
 616
 617 &usdhc3 {
 618         pinctrl-names = "default";
 619         pinctrl-0 = <&pinctrl_usdhc3>;
 620         bus-width = <4>;
 621         cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
 622         wp-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
 623         no-1-8-v;
 624         keep-power-in-suspend;
 625         wakeup-source;
 626         vmmc-supply = <&sw2_reg>;
 627         status = "disabled";
 628 };
 629
 630 &usdhc4 {
 631         pinctrl-names = "default";
 632         pinctrl-0 = <&pinctrl_usdhc4>;
 633         bus-width = <8>;
 634         non-removable;
 635         no-1-8-v;
 636         keep-power-in-suspend;
 637         vmmc-supply = <&sw2_reg>;
 638         status = "okay";
 639 };
 640
 641 &wdog1 {
 642         status = "disabled";
 643 };
 644
 645 &wdog2 {
 646         pinctrl-names = "default";
 647         pinctrl-0 = <&pinctrl_wdog>;
 648         fsl,ext-reset-output;
 649         status = "okay";
 650 };