arch/arm/boot/dts/bcm2836-rpi-2-b.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 /dts-v1/;
   3 #include "bcm2836.dtsi"
   4 #include "bcm2836-rpi.dtsi"
   5 #include "bcm283x-rpi-smsc9514.dtsi"
   6 #include "bcm283x-rpi-usb-host.dtsi"
   7
   8 / {
   9         compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
  10         model = "Raspberry Pi 2 Model B";
  11
  12         memory@0 {
  13                 device_type = "memory";
  14                 reg = <0 0x40000000>;
  15         };
  16
  17         leds {
  18                 led-act {
  19                         gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
  20                 };
  21
  22                 led-pwr {
  23                         label = "PWR";
  24                         gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
  25                         default-state = "keep";
  26                         linux,default-trigger = "default-on";
  27                 };
  28         };
  29 };
  30
  31 &gpio {
  32         /*
  33          * Taken from rpi_SCH_2b_1p2_reduced.pdf and
  34          * the official GPU firmware DT blob.
  35          *
  36          * Legend:
  37          * "NC" = not connected (no rail from the SoC)
  38          * "FOO" = GPIO line named "FOO" on the schematic
  39          * "FOO_N" = GPIO line named "FOO" on schematic, active low
  40          */
  41         gpio-line-names = "ID_SDA",
  42                           "ID_SCL",
  43                           "SDA1",
  44                           "SCL1",
  45                           "GPIO_GCLK",
  46                           "GPIO5",
  47                           "GPIO6",
  48                           "SPI_CE1_N",
  49                           "SPI_CE0_N",
  50                           "SPI_MISO",
  51                           "SPI_MOSI",
  52                           "SPI_SCLK",
  53                           "GPIO12",
  54                           "GPIO13",
  55                           /* Serial port */
  56                           "TXD0",
  57                           "RXD0",
  58                           "GPIO16",
  59                           "GPIO17",
  60                           "GPIO18",
  61                           "GPIO19",
  62                           "GPIO20",
  63                           "GPIO21",
  64                           "GPIO22",
  65                           "GPIO23",
  66                           "GPIO24",
  67                           "GPIO25",
  68                           "GPIO26",
  69                           "GPIO27",
  70                           "SDA0",
  71                           "SCL0",
  72                           "", /* GPIO30 */
  73                           "LAN_RUN",
  74                           "CAM_GPIO1",
  75                           "", /* GPIO33 */
  76                           "", /* GPIO34 */
  77                           "PWR_LOW_N",
  78                           "", /* GPIO36 */
  79                           "", /* GPIO37 */
  80                           "USB_LIMIT",
  81                           "", /* GPIO39 */
  82                           "PWM0_OUT",
  83                           "CAM_GPIO0",
  84                           "SMPS_SCL",
  85                           "SMPS_SDA",
  86                           "ETHCLK",
  87                           "PWM1_OUT",
  88                           "HDMI_HPD_N",
  89                           "STATUS_LED",
  90                           /* Used by SD Card */
  91                           "SD_CLK_R",
  92                           "SD_CMD_R",
  93                           "SD_DATA0_R",
  94                           "SD_DATA1_R",
  95                           "SD_DATA2_R",
  96                           "SD_DATA3_R";
  97
  98         pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
  99
 100         /* I2S interface */
 101         i2s_alt0: i2s_alt0 {
 102                 brcm,pins = <18 19 20 21>;
 103                 brcm,function = <BCM2835_FSEL_ALT0>;
 104         };
 105 };
 106
 107 &hdmi {
 108         hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 109         power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
 110         status = "okay";
 111 };
 112
 113 &pwm {
 114         pinctrl-names = "default";
 115         pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
 116         status = "okay";
 117 };
 118
 119 &sdhost {
 120         pinctrl-names = "default";
 121         pinctrl-0 = <&sdhost_gpio48>;
 122         bus-width = <4>;
 123         status = "okay";
 124 };
 125
 126 &uart0 {
 127         pinctrl-names = "default";
 128         pinctrl-0 = <&uart0_gpio14>;
 129         status = "okay";
 130 };