arch/arm/boot/dts/am335x-netcan-plus-1xx.dts

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
   4  */
   5
   6 /*
   7  * VScom OnRISC
   8  * http://www.vscom.de
   9  */
  10
  11 /dts-v1/;
  12
  13 #include "am335x-baltos.dtsi"
  14 #include "am335x-baltos-leds.dtsi"
  15
  16 / {
  17         model = "NetCAN";
  18
  19         leds {
  20                 pinctrl-names = "default";
  21                 pinctrl-0 = <&user_leds_s0>;
  22
  23                 compatible = "gpio-leds";
  24
  25                 led@1 {
  26                         label = "can_data";
  27                         linux,default-trigger = "netdev";
  28                         gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
  29                         default-state = "off";
  30                 };
  31                 led@2 {
  32                         label = "can_error";
  33                         gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
  34                         default-state = "off";
  35                 };
  36         };
  37 };
  38
  39 &am33xx_pinmux {
  40         user_leds_s0: user_leds_s0 {
  41                 pinctrl-single,pins = <
  42                         AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7)    /* CAN Data LED */
  43                         AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7)    /* CAN Error LED */
  44                 >;
  45         };
  46
  47         dcan1_pins: pinmux_dcan1_pins {
  48                 pinctrl-single,pins = <
  49                         AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2)    /* CAN TX */
  50                         AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2)     /* CAN RX */
  51                 >;
  52         };
  53 };
  54
  55 &usb0_phy {
  56         status = "okay";
  57 };
  58
  59 &usb0 {
  60         status = "okay";
  61         dr_mode = "host";
  62 };
  63
  64 &davinci_mdio_sw {
  65         phy0: ethernet-phy@0 {
  66                 reg = <1>;
  67         };
  68 };
  69
  70 &cpsw_port1 {
  71         phy-mode = "rmii";
  72         ti,dual-emac-pvid = <1>;
  73         phy-handle = <&phy0>;
  74 };
  75
  76 &cpsw_port2 {
  77         phy-mode = "rgmii-id";
  78         ti,dual-emac-pvid = <2>;
  79         phy-handle = <&phy1>;
  80 };
  81
  82 &dcan1 {
  83         pinctrl-names = "default";
  84         pinctrl-0 = <&dcan1_pins>;
  85
  86         status = "okay";
  87 };