Merge tag 'block-5.14-2021-08-07' of git://git.kernel.dk/linux-block

[linux-2.6-microblaze.git] / Documentation / dev-tools / kunit / usage.rst

.. SPDX-License-Identifier: GPL-2.0

===========
Using KUnit
===========

The purpose of this document is to describe what KUnit is, how it works, how it
is intended to be used, and all the concepts and terminology that are needed to
understand it. This guide assumes a working knowledge of the Linux kernel and
some basic knowledge of testing.

For a high level introduction to KUnit, including setting up KUnit for your
project, see Documentation/dev-tools/kunit/start.rst.

Organization of this document
=============================

This document is organized into two main sections: Testing and Common Patterns.
The first covers what unit tests are and how to use KUnit to write them. The
second covers common testing patterns, e.g. how to isolate code and make it
possible to unit test code that was otherwise un-unit-testable.

Testing
=======

What is KUnit?
--------------

"K" is short for "kernel" so "KUnit" is the "(Linux) Kernel Unit Testing
Framework." KUnit is intended first and foremost for writing unit tests; it is
general enough that it can be used to write integration tests; however, this is
a secondary goal. KUnit has no ambition of being the only testing framework for
the kernel; for example, it does not intend to be an end-to-end testing
framework.

What is Unit Testing?
---------------------

A `unit test <https://martinfowler.com/bliki/UnitTest.html>`_ is a test that
tests code at the smallest possible scope, a *unit* of code. In the C
programming language that's a function.

Unit tests should be written for all the publicly exposed functions in a
compilation unit; so that is all the functions that are exported in either a
*class* (defined below) or all functions which are **not** static.

Writing Tests
-------------

Test Cases
~~~~~~~~~~

The fundamental unit in KUnit is the test case. A test case is a function with
the signature ``void (*)(struct kunit *test)``. It calls a function to be tested
and then sets *expectations* for what should happen. For example:

.. code-block:: c

        void example_test_success(struct kunit *test)
        {
        }

        void example_test_failure(struct kunit *test)
        {
                KUNIT_FAIL(test, "This test never passes.");
        }

In the above example ``example_test_success`` always passes because it does
nothing; no expectations are set, so all expectations pass. On the other hand
``example_test_failure`` always fails because it calls ``KUNIT_FAIL``, which is
a special expectation that logs a message and causes the test case to fail.

Expectations
~~~~~~~~~~~~
An *expectation* is a way to specify that you expect a piece of code to do
something in a test. An expectation is called like a function. A test is made
by setting expectations about the behavior of a piece of code under test; when
one or more of the expectations fail, the test case fails and information about
the failure is logged. For example:

.. code-block:: c

        void add_test_basic(struct kunit *test)
        {
                KUNIT_EXPECT_EQ(test, 1, add(1, 0));
                KUNIT_EXPECT_EQ(test, 2, add(1, 1));
        }

In the above example ``add_test_basic`` makes a number of assertions about the
behavior of a function called ``add``; the first parameter is always of type
``struct kunit *``, which contains information about the current test context;
the second parameter, in this case, is what the value is expected to be; the
last value is what the value actually is. If ``add`` passes all of these
expectations, the test case, ``add_test_basic`` will pass; if any one of these
expectations fails, the test case will fail.

It is important to understand that a test case *fails* when any expectation is
violated; however, the test will continue running, potentially trying other
expectations until the test case ends or is otherwise terminated. This is as
opposed to *assertions* which are discussed later.

To learn about more expectations supported by KUnit, see
Documentation/dev-tools/kunit/api/test.rst.

.. note::
   A single test case should be pretty short, pretty easy to understand,
   focused on a single behavior.

For example, if we wanted to properly test the add function above, we would
create additional tests cases which would each test a different property that an
add function should have like this:

.. code-block:: c

        void add_test_basic(struct kunit *test)
        {
                KUNIT_EXPECT_EQ(test, 1, add(1, 0));
                KUNIT_EXPECT_EQ(test, 2, add(1, 1));
        }

        void add_test_negative(struct kunit *test)
        {
                KUNIT_EXPECT_EQ(test, 0, add(-1, 1));
        }

        void add_test_max(struct kunit *test)
        {
                KUNIT_EXPECT_EQ(test, INT_MAX, add(0, INT_MAX));
                KUNIT_EXPECT_EQ(test, -1, add(INT_MAX, INT_MIN));
        }

        void add_test_overflow(struct kunit *test)
        {
                KUNIT_EXPECT_EQ(test, INT_MIN, add(INT_MAX, 1));
        }

Notice how it is immediately obvious what all the properties that we are testing
for are.

Assertions
~~~~~~~~~~

KUnit also has the concept of an *assertion*. An assertion is just like an
expectation except the assertion immediately terminates the test case if it is
not satisfied.

For example:

.. code-block:: c

        static void mock_test_do_expect_default_return(struct kunit *test)
        {
                struct mock_test_context *ctx = test->priv;
                struct mock *mock = ctx->mock;
                int param0 = 5, param1 = -5;
                const char *two_param_types[] = {"int", "int"};
                const void *two_params[] = {&param0, &param1};
                const void *ret;

                ret = mock->do_expect(mock,
                                      "test_printk", test_printk,
                                      two_param_types, two_params,
                                      ARRAY_SIZE(two_params));
                KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ret);
                KUNIT_EXPECT_EQ(test, -4, *((int *) ret));
        }

In this example, the method under test should return a pointer to a value, so
if the pointer returned by the method is null or an errno, we don't want to
bother continuing the test since the following expectation could crash the test
case. `ASSERT_NOT_ERR_OR_NULL(...)` allows us to bail out of the test case if
the appropriate conditions have not been satisfied to complete the test.

Test Suites
~~~~~~~~~~~

Now obviously one unit test isn't very helpful; the power comes from having
many test cases covering all of a unit's behaviors. Consequently it is common
to have many *similar* tests; in order to reduce duplication in these closely
related tests most unit testing frameworks - including KUnit - provide the
concept of a *test suite*. A *test suite* is just a collection of test cases
for a unit of code with a set up function that gets invoked before every test
case and then a tear down function that gets invoked after every test case
completes.

Example:

.. code-block:: c

        static struct kunit_case example_test_cases[] = {
                KUNIT_CASE(example_test_foo),
                KUNIT_CASE(example_test_bar),
                KUNIT_CASE(example_test_baz),
                {}
        };

        static struct kunit_suite example_test_suite = {
                .name = "example",
                .init = example_test_init,
                .exit = example_test_exit,
                .test_cases = example_test_cases,
        };
        kunit_test_suite(example_test_suite);

In the above example the test suite, ``example_test_suite``, would run the test
cases ``example_test_foo``, ``example_test_bar``, and ``example_test_baz``;
each would have ``example_test_init`` called immediately before it and would
have ``example_test_exit`` called immediately after it.
``kunit_test_suite(example_test_suite)`` registers the test suite with the
KUnit test framework.

.. note::
   A test case will only be run if it is associated with a test suite.

``kunit_test_suite(...)`` is a macro which tells the linker to put the specified
test suite in a special linker section so that it can be run by KUnit either
after late_init, or when the test module is loaded (depending on whether the
test was built in or not).

For more information on these types of things see the
Documentation/dev-tools/kunit/api/test.rst.

Common Patterns
===============

Isolating Behavior
------------------

The most important aspect of unit testing that other forms of testing do not
provide is the ability to limit the amount of code under test to a single unit.
In practice, this is only possible by being able to control what code gets run
when the unit under test calls a function and this is usually accomplished
through some sort of indirection where a function is exposed as part of an API
such that the definition of that function can be changed without affecting the
rest of the code base. In the kernel this primarily comes from two constructs,
classes, structs that contain function pointers that are provided by the
implementer, and architecture-specific functions which have definitions selected
at compile time.

Classes
~~~~~~~

Classes are not a construct that is built into the C programming language;
however, it is an easily derived concept. Accordingly, pretty much every project
that does not use a standardized object oriented library (like GNOME's GObject)
has their own slightly different way of doing object oriented programming; the
Linux kernel is no exception.

The central concept in kernel object oriented programming is the class. In the
kernel, a *class* is a struct that contains function pointers. This creates a
contract between *implementers* and *users* since it forces them to use the
same function signature without having to call the function directly. In order
for it to truly be a class, the function pointers must specify that a pointer
to the class, known as a *class handle*, be one of the parameters; this makes
it possible for the member functions (also known as *methods*) to have access
to member variables (more commonly known as *fields*) allowing the same
implementation to have multiple *instances*.

Typically a class can be *overridden* by *child classes* by embedding the
*parent class* in the child class. Then when a method provided by the child
class is called, the child implementation knows that the pointer passed to it is
of a parent contained within the child; because of this, the child can compute
the pointer to itself because the pointer to the parent is always a fixed offset
from the pointer to the child; this offset is the offset of the parent contained
in the child struct. For example:

.. code-block:: c

        struct shape {
                int (*area)(struct shape *this);
        };

        struct rectangle {
                struct shape parent;
                int length;
                int width;
        };

        int rectangle_area(struct shape *this)
        {
                struct rectangle *self = container_of(this, struct shape, parent);

                return self->length * self->width;
        };

        void rectangle_new(struct rectangle *self, int length, int width)
        {
                self->parent.area = rectangle_area;
                self->length = length;
                self->width = width;
        }

In this example (as in most kernel code) the operation of computing the pointer
to the child from the pointer to the parent is done by ``container_of``.

Faking Classes
~~~~~~~~~~~~~~

In order to unit test a piece of code that calls a method in a class, the
behavior of the method must be controllable, otherwise the test ceases to be a
unit test and becomes an integration test.

A fake just provides an implementation of a piece of code that is different than
what runs in a production instance, but behaves identically from the standpoint
of the callers; this is usually done to replace a dependency that is hard to
deal with, or is slow.

A good example for this might be implementing a fake EEPROM that just stores the
"contents" in an internal buffer. For example, let's assume we have a class that
represents an EEPROM:

.. code-block:: c

        struct eeprom {
                ssize_t (*read)(struct eeprom *this, size_t offset, char *buffer, size_t count);
                ssize_t (*write)(struct eeprom *this, size_t offset, const char *buffer, size_t count);
        };

And we want to test some code that buffers writes to the EEPROM:

.. code-block:: c

        struct eeprom_buffer {
                ssize_t (*write)(struct eeprom_buffer *this, const char *buffer, size_t count);
                int flush(struct eeprom_buffer *this);
                size_t flush_count; /* Flushes when buffer exceeds flush_count. */
        };

        struct eeprom_buffer *new_eeprom_buffer(struct eeprom *eeprom);
        void destroy_eeprom_buffer(struct eeprom *eeprom);

We can easily test this code by *faking out* the underlying EEPROM:

.. code-block:: c

        struct fake_eeprom {
                struct eeprom parent;
                char contents[FAKE_EEPROM_CONTENTS_SIZE];
        };

        ssize_t fake_eeprom_read(struct eeprom *parent, size_t offset, char *buffer, size_t count)
        {
                struct fake_eeprom *this = container_of(parent, struct fake_eeprom, parent);

                count = min(count, FAKE_EEPROM_CONTENTS_SIZE - offset);
                memcpy(buffer, this->contents + offset, count);

                return count;
        }

        ssize_t fake_eeprom_write(struct eeprom *parent, size_t offset, const char *buffer, size_t count)
        {
                struct fake_eeprom *this = container_of(parent, struct fake_eeprom, parent);

                count = min(count, FAKE_EEPROM_CONTENTS_SIZE - offset);
                memcpy(this->contents + offset, buffer, count);

                return count;
        }

        void fake_eeprom_init(struct fake_eeprom *this)
        {
                this->parent.read = fake_eeprom_read;
                this->parent.write = fake_eeprom_write;
                memset(this->contents, 0, FAKE_EEPROM_CONTENTS_SIZE);
        }

We can now use it to test ``struct eeprom_buffer``:

.. code-block:: c

        struct eeprom_buffer_test {
                struct fake_eeprom *fake_eeprom;
                struct eeprom_buffer *eeprom_buffer;
        };

        static void eeprom_buffer_test_does_not_write_until_flush(struct kunit *test)
        {
                struct eeprom_buffer_test *ctx = test->priv;
                struct eeprom_buffer *eeprom_buffer = ctx->eeprom_buffer;
                struct fake_eeprom *fake_eeprom = ctx->fake_eeprom;
                char buffer[] = {0xff};

                eeprom_buffer->flush_count = SIZE_MAX;

                eeprom_buffer->write(eeprom_buffer, buffer, 1);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0);

                eeprom_buffer->write(eeprom_buffer, buffer, 1);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[1], 0);

                eeprom_buffer->flush(eeprom_buffer);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0xff);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[1], 0xff);
        }

        static void eeprom_buffer_test_flushes_after_flush_count_met(struct kunit *test)
        {
                struct eeprom_buffer_test *ctx = test->priv;
                struct eeprom_buffer *eeprom_buffer = ctx->eeprom_buffer;
                struct fake_eeprom *fake_eeprom = ctx->fake_eeprom;
                char buffer[] = {0xff};

                eeprom_buffer->flush_count = 2;

                eeprom_buffer->write(eeprom_buffer, buffer, 1);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0);

                eeprom_buffer->write(eeprom_buffer, buffer, 1);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0xff);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[1], 0xff);
        }

        static void eeprom_buffer_test_flushes_increments_of_flush_count(struct kunit *test)
        {
                struct eeprom_buffer_test *ctx = test->priv;
                struct eeprom_buffer *eeprom_buffer = ctx->eeprom_buffer;
                struct fake_eeprom *fake_eeprom = ctx->fake_eeprom;
                char buffer[] = {0xff, 0xff};

                eeprom_buffer->flush_count = 2;

                eeprom_buffer->write(eeprom_buffer, buffer, 1);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0);

                eeprom_buffer->write(eeprom_buffer, buffer, 2);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[0], 0xff);
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[1], 0xff);
                /* Should have only flushed the first two bytes. */
                KUNIT_EXPECT_EQ(test, fake_eeprom->contents[2], 0);
        }

        static int eeprom_buffer_test_init(struct kunit *test)
        {
                struct eeprom_buffer_test *ctx;

                ctx = kunit_kzalloc(test, sizeof(*ctx), GFP_KERNEL);
                KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ctx);

                ctx->fake_eeprom = kunit_kzalloc(test, sizeof(*ctx->fake_eeprom), GFP_KERNEL);
                KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ctx->fake_eeprom);
                fake_eeprom_init(ctx->fake_eeprom);

                ctx->eeprom_buffer = new_eeprom_buffer(&ctx->fake_eeprom->parent);
                KUNIT_ASSERT_NOT_ERR_OR_NULL(test, ctx->eeprom_buffer);

                test->priv = ctx;

                return 0;
        }

        static void eeprom_buffer_test_exit(struct kunit *test)
        {
                struct eeprom_buffer_test *ctx = test->priv;

                destroy_eeprom_buffer(ctx->eeprom_buffer);
        }

Testing against multiple inputs
-------------------------------

Testing just a few inputs might not be enough to have confidence that the code
works correctly, e.g. for a hash function.

In such cases, it can be helpful to have a helper macro or function, e.g. this
fictitious example for ``sha1sum(1)``

.. code-block:: c

        #define TEST_SHA1(in, want) \
                sha1sum(in, out); \
                KUNIT_EXPECT_STREQ_MSG(test, out, want, "sha1sum(%s)", in);

        char out[40];
        TEST_SHA1("hello world",  "2aae6c35c94fcfb415dbe95f408b9ce91ee846ed");
        TEST_SHA1("hello world!", "430ce34d020724ed75a196dfc2ad67c77772d169");


Note the use of ``KUNIT_EXPECT_STREQ_MSG`` to give more context when it fails
and make it easier to track down. (Yes, in this example, ``want`` is likely
going to be unique enough on its own).

The ``_MSG`` variants are even more useful when the same expectation is called
multiple times (in a loop or helper function) and thus the line number isn't
enough to identify what failed, like below.

In some cases, it can be helpful to write a *table-driven test* instead, e.g.

.. code-block:: c

        int i;
        char out[40];

        struct sha1_test_case {
                const char *str;
                const char *sha1;
        };

        struct sha1_test_case cases[] = {
                {
                        .str = "hello world",
                        .sha1 = "2aae6c35c94fcfb415dbe95f408b9ce91ee846ed",
                },
                {
                        .str = "hello world!",
                        .sha1 = "430ce34d020724ed75a196dfc2ad67c77772d169",
                },
        };
        for (i = 0; i < ARRAY_SIZE(cases); ++i) {
                sha1sum(cases[i].str, out);
                KUNIT_EXPECT_STREQ_MSG(test, out, cases[i].sha1,
                                      "sha1sum(%s)", cases[i].str);
        }


There's more boilerplate involved, but it can:

* be more readable when there are multiple inputs/outputs thanks to field names,

  * E.g. see ``fs/ext4/inode-test.c`` for an example of both.
* reduce duplication if test cases can be shared across multiple tests.

  * E.g. if we wanted to also test ``sha256sum``, we could add a ``sha256``
    field and reuse ``cases``.

* be converted to a "parameterized test", see below.

Parameterized Testing
~~~~~~~~~~~~~~~~~~~~~

The table-driven testing pattern is common enough that KUnit has special
support for it.

Reusing the same ``cases`` array from above, we can write the test as a
"parameterized test" with the following.

.. code-block:: c

        // This is copy-pasted from above.
        struct sha1_test_case {
                const char *str;
                const char *sha1;
        };
        struct sha1_test_case cases[] = {
                {
                        .str = "hello world",
                        .sha1 = "2aae6c35c94fcfb415dbe95f408b9ce91ee846ed",
                },
                {
                        .str = "hello world!",
                        .sha1 = "430ce34d020724ed75a196dfc2ad67c77772d169",
                },
        };

        // Need a helper function to generate a name for each test case.
        static void case_to_desc(const struct sha1_test_case *t, char *desc)
        {
                strcpy(desc, t->str);
        }
        // Creates `sha1_gen_params()` to iterate over `cases`.
        KUNIT_ARRAY_PARAM(sha1, cases, case_to_desc);

        // Looks no different from a normal test.
        static void sha1_test(struct kunit *test)
        {
                // This function can just contain the body of the for-loop.
                // The former `cases[i]` is accessible under test->param_value.
                char out[40];
                struct sha1_test_case *test_param = (struct sha1_test_case *)(test->param_value);

                sha1sum(test_param->str, out);
                KUNIT_EXPECT_STREQ_MSG(test, out, test_param->sha1,
                                      "sha1sum(%s)", test_param->str);
        }

        // Instead of KUNIT_CASE, we use KUNIT_CASE_PARAM and pass in the
        // function declared by KUNIT_ARRAY_PARAM.
        static struct kunit_case sha1_test_cases[] = {
                KUNIT_CASE_PARAM(sha1_test, sha1_gen_params),
                {}
        };

.. _kunit-on-non-uml:

KUnit on non-UML architectures
==============================

By default KUnit uses UML as a way to provide dependencies for code under test.
Under most circumstances KUnit's usage of UML should be treated as an
implementation detail of how KUnit works under the hood. Nevertheless, there
are instances where being able to run architecture-specific code or test
against real hardware is desirable. For these reasons KUnit supports running on
other architectures.

Running existing KUnit tests on non-UML architectures
-----------------------------------------------------

There are some special considerations when running existing KUnit tests on
non-UML architectures:

*   Hardware may not be deterministic, so a test that always passes or fails
    when run under UML may not always do so on real hardware.
*   Hardware and VM environments may not be hermetic. KUnit tries its best to
    provide a hermetic environment to run tests; however, it cannot manage state
    that it doesn't know about outside of the kernel. Consequently, tests that
    may be hermetic on UML may not be hermetic on other architectures.
*   Some features and tooling may not be supported outside of UML.
*   Hardware and VMs are slower than UML.

None of these are reasons not to run your KUnit tests on real hardware; they are
only things to be aware of when doing so.

Currently, the KUnit Wrapper (``tools/testing/kunit/kunit.py``) (aka
kunit_tool) only fully supports running tests inside of UML and QEMU; however,
this is only due to our own time limitations as humans working on KUnit. It is
entirely possible to support other emulators and even actual hardware, but for
now QEMU and UML is what is fully supported within the KUnit Wrapper. Again, to
be clear, this is just the Wrapper. The actualy KUnit tests and the KUnit
library they are written in is fully architecture agnostic and can be used in
virtually any setup, you just won't have the benefit of typing a single command
out of the box and having everything magically work perfectly.

Again, all core KUnit framework features are fully supported on all
architectures, and using them is straightforward: Most popular architectures
are supported directly in the KUnit Wrapper via QEMU. Currently, supported
architectures on QEMU include:

*   i386
*   x86_64
*   arm
*   arm64
*   alpha
*   powerpc
*   riscv
*   s390
*   sparc

In order to run KUnit tests on one of these architectures via QEMU with the
KUnit wrapper, all you need to do is specify the flags ``--arch`` and
``--cross_compile`` when invoking the KUnit Wrapper. For example, we could run
the default KUnit tests on ARM in the following manner (assuming we have an ARM
toolchain installed):

.. code-block:: bash

        tools/testing/kunit/kunit.py run --timeout=60 --jobs=12 --arch=arm --cross_compile=arm-linux-gnueabihf-

Alternatively, if you want to run your tests on real hardware or in some other
emulation environment, all you need to do is to take your kunitconfig, your
Kconfig options for the tests you would like to run, and merge them into
whatever config your are using for your platform. That's it!

For example, let's say you have the following kunitconfig:

.. code-block:: none

        CONFIG_KUNIT=y
        CONFIG_KUNIT_EXAMPLE_TEST=y

If you wanted to run this test on an x86 VM, you might add the following config
options to your ``.config``:

.. code-block:: none

        CONFIG_KUNIT=y
        CONFIG_KUNIT_EXAMPLE_TEST=y
        CONFIG_SERIAL_8250=y
        CONFIG_SERIAL_8250_CONSOLE=y

All these new options do is enable support for a common serial console needed
for logging.

Next, you could build a kernel with these tests as follows:


.. code-block:: bash

        make ARCH=x86 olddefconfig
        make ARCH=x86

Once you have built a kernel, you could run it on QEMU as follows:

.. code-block:: bash

        qemu-system-x86_64 -enable-kvm \
                           -m 1024 \
                           -kernel arch/x86_64/boot/bzImage \
                           -append 'console=ttyS0' \
                           --nographic

Interspersed in the kernel logs you might see the following:

.. code-block:: none

        TAP version 14
                # Subtest: example
                1..1
                # example_simple_test: initializing
                ok 1 - example_simple_test
        ok 1 - example

Congratulations, you just ran a KUnit test on the x86 architecture!

In a similar manner, kunit and kunit tests can also be built as modules,
so if you wanted to run tests in this way you might add the following config
options to your ``.config``:

.. code-block:: none

        CONFIG_KUNIT=m
        CONFIG_KUNIT_EXAMPLE_TEST=m

Once the kernel is built and installed, a simple

.. code-block:: bash

        modprobe example-test

...will run the tests.

.. note::
   Note that you should make sure your test depends on ``KUNIT=y`` in Kconfig
   if the test does not support module build.  Otherwise, it will trigger
   compile errors if ``CONFIG_KUNIT`` is ``m``.

Writing new tests for other architectures
-----------------------------------------

The first thing you must do is ask yourself whether it is necessary to write a
KUnit test for a specific architecture, and then whether it is necessary to
write that test for a particular piece of hardware. In general, writing a test
that depends on having access to a particular piece of hardware or software (not
included in the Linux source repo) should be avoided at all costs.

Even if you only ever plan on running your KUnit test on your hardware
configuration, other people may want to run your tests and may not have access
to your hardware. If you write your test to run on UML, then anyone can run your
tests without knowing anything about your particular setup, and you can still
run your tests on your hardware setup just by compiling for your architecture.

.. important::
   Always prefer tests that run on UML to tests that only run under a particular
   architecture, and always prefer tests that run under QEMU or another easy
   (and monetarily free) to obtain software environment to a specific piece of
   hardware.

Nevertheless, there are still valid reasons to write an architecture or hardware
specific test: for example, you might want to test some code that really belongs
in ``arch/some-arch/*``. Even so, try your best to write the test so that it
does not depend on physical hardware: if some of your test cases don't need the
hardware, only require the hardware for tests that actually need it.

Now that you have narrowed down exactly what bits are hardware specific, the
actual procedure for writing and running the tests is pretty much the same as
writing normal KUnit tests. One special caveat is that you have to reset
hardware state in between test cases; if this is not possible, you may only be
able to run one test case per invocation.

.. TODO(brendanhiggins@google.com): Add an actual example of an architecture-
   dependent KUnit test.

KUnit debugfs representation
============================
When kunit test suites are initialized, they create an associated directory
in ``/sys/kernel/debug/kunit/<test-suite>``.  The directory contains one file

- results: "cat results" displays results of each test case and the results
  of the entire suite for the last test run.

The debugfs representation is primarily of use when kunit test suites are
run in a native environment, either as modules or builtin.  Having a way
to display results like this is valuable as otherwise results can be
intermixed with other events in dmesg output.  The maximum size of each
results file is KUNIT_LOG_SIZE bytes (defined in ``include/kunit/test.h``).