From 67b01837861c203c51f78320dcf49fe7ec2f634d Mon Sep 17 00:00:00 2001 From: Philippe Schenker Date: Thu, 17 Oct 2019 14:14:42 +0000 Subject: [PATCH] tty: serial: lpuart: Add RS485 support for 32-bit uart flavour This commits adds RS485 support for LPUART hardware that uses 32-bit registers. These are typically found in i.MX8 processors. Signed-off-by: Philippe Schenker Reviewed-by: Fugang Duan Link: https://lore.kernel.org/r/20191017141428.10330-3-philippe.schenker@toradex.com Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/fsl_lpuart.c | 65 ++++++++++++++++++++++++++++++++- 1 file changed, 63 insertions(+), 2 deletions(-) diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c index 346b4a070ce9..22df5f8f48b6 100644 --- a/drivers/tty/serial/fsl_lpuart.c +++ b/drivers/tty/serial/fsl_lpuart.c @@ -1280,6 +1280,57 @@ static int lpuart_config_rs485(struct uart_port *port, return 0; } +static int lpuart32_config_rs485(struct uart_port *port, + struct serial_rs485 *rs485) +{ + struct lpuart_port *sport = container_of(port, + struct lpuart_port, port); + + unsigned long modem = lpuart32_read(&sport->port, UARTMODIR) + & ~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE); + lpuart32_write(&sport->port, modem, UARTMODIR); + + /* clear unsupported configurations */ + rs485->delay_rts_before_send = 0; + rs485->delay_rts_after_send = 0; + rs485->flags &= ~SER_RS485_RX_DURING_TX; + + if (rs485->flags & SER_RS485_ENABLED) { + /* Enable auto RS-485 RTS mode */ + modem |= UARTMODEM_TXRTSE; + + /* + * RTS needs to be logic HIGH either during transer _or_ after + * transfer, other variants are not supported by the hardware. + */ + + if (!(rs485->flags & (SER_RS485_RTS_ON_SEND | + SER_RS485_RTS_AFTER_SEND))) + rs485->flags |= SER_RS485_RTS_ON_SEND; + + if (rs485->flags & SER_RS485_RTS_ON_SEND && + rs485->flags & SER_RS485_RTS_AFTER_SEND) + rs485->flags &= ~SER_RS485_RTS_AFTER_SEND; + + /* + * The hardware defaults to RTS logic HIGH while transfer. + * Switch polarity in case RTS shall be logic HIGH + * after transfer. + * Note: UART is assumed to be active high. + */ + if (rs485->flags & SER_RS485_RTS_ON_SEND) + modem &= ~UARTMODEM_TXRTSPOL; + else if (rs485->flags & SER_RS485_RTS_AFTER_SEND) + modem |= UARTMODEM_TXRTSPOL; + } + + /* Store the new configuration */ + sport->port.rs485 = *rs485; + + lpuart32_write(&sport->port, modem, UARTMODIR); + return 0; +} + static unsigned int lpuart_get_mctrl(struct uart_port *port) { unsigned int temp = 0; @@ -1878,6 +1929,13 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios, ctrl |= UARTCTRL_M; } + /* + * When auto RS-485 RTS mode is enabled, + * hardware flow control need to be disabled. + */ + if (sport->port.rs485.flags & SER_RS485_ENABLED) + termios->c_cflag &= ~CRTSCTS; + if (termios->c_cflag & CRTSCTS) { modem |= (UARTMODIR_RXRTSE | UARTMODIR_TXCTSE); } else { @@ -2405,7 +2463,10 @@ static int lpuart_probe(struct platform_device *pdev) sport->port.ops = &lpuart_pops; sport->port.flags = UPF_BOOT_AUTOCONF; - sport->port.rs485_config = lpuart_config_rs485; + if (lpuart_is_32(sport)) + sport->port.rs485_config = lpuart32_config_rs485; + else + sport->port.rs485_config = lpuart_config_rs485; sport->ipg_clk = devm_clk_get(&pdev->dev, "ipg"); if (IS_ERR(sport->ipg_clk)) { @@ -2459,7 +2520,7 @@ static int lpuart_probe(struct platform_device *pdev) sport->port.rs485.delay_rts_after_send) dev_err(&pdev->dev, "driver doesn't support RTS delays\n"); - lpuart_config_rs485(&sport->port, &sport->port.rs485); + sport->port.rs485_config(&sport->port, &sport->port.rs485); sport->dma_tx_chan = dma_request_slave_channel(sport->port.dev, "tx"); if (!sport->dma_tx_chan) -- 2.20.1