drm/i915: Don't enable hpd detection logic from irq_postinstall()

No reason that I can see why we should enable the hpd detection logic
already during irq postinstall phase. We don't even do this on all
the platforms. We just need it before we actually enable the hotplug
interrupts in .hpd_irq_setup(), and in fact we already do it there as
well. Let's just eliminate the redundant early setup.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-15-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>

drm/i915: Split gen11_hpd_detection_setup() into tc vs. tbt variants

No reason to stuff both type-c and tbt into the same function.
Let's split this so we may more easily handle platforms that
lack the tbt spefific bits.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-14-ville.syrjala@linux.intel.com

drm/i915: Relocate intel_hpd_{enabled,hotplug}_irqs()

Move intel_hpd_{enabled,hotplug}_irqs() closes to the beginning of
the file so we can use them in more places. No functional changes.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-13-ville.syrjala@linux.intel.com

drm/i915: s/tc_port/hpd_pin/ in icp+ TC hotplug bits

Parametrize the icp+ TC HPD bits using hpd_pin rather than
tc_port so it's clear what kind of an animal we're dealing
with.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-12-ville.syrjala@linux.intel.com

drm/i915: s/tc_port/hpd_pin/ in GEN11_{TC,TBT}_HOTPLUG()

Use hpd_pin instead of tc_port in the GEN11_{TC,TBT}_HOTPLUG()
to make it clear what they refer to.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-11-ville.syrjala@linux.intel.com

drm/i915: s/port/hpd_pin/ for icp+ ddi hpd bits

Use hpd_pin instead of port in the parametrized ICP+ DDI HPD
macros. Makes it clear what these refer to.

v2: Handle DG1

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-10-ville.syrjala@linux.intel.com

drm/i915: Introduce GEN8_DE_PORT_HOTPLUG()

Unify the BDW/BXT hotplug bits. BDW only has port A, but that
matches BXT port A so we can shar the same macro for both.

v2: Remember the gvt

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-9-ville.syrjala@linux.intel.com

drm/i915: Parametrize BXT_DE_PORT_HP_DDI with hpd_pin

Use hpd_pin to parametrize BXT_DE_PORT_HP_DDI() to make it clear
these have nothing to do with DDI ports or PHYs as such. The only
thing that matters is the HPD pin assignment.

v2: Remember the gvt

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-8-ville.syrjala@linux.intel.com

drm/i915: Use AUX_CH_USBCn for the RKL VBT AUX CH setup

As with the VBT DVO port, RKL uses PHY based mapping for the
VBT AUX CH. Adjust the code to use the new AUX_USBCn names
and add a comment to explain the situation.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-7-ville.syrjala@linux.intel.com

drm/i915: Pimp AUX CH names

Let's make the AUX CH names match the spec (AUX A-F for pre-tgl,
AUX A-C or AUX USBC1-6 for tgl+). And while at it let's include
the full encoder name in the AUX CH name as well (as opposed to
just using port_name() which wouldn't give us the right thing on
tgl+).

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-6-ville.syrjala@linux.intel.com

drm/i915: Introduce AUX_CH_USBCn

Just like with the DDIs tgl+ renamed the AUX CHs to reflect
the type of the DDI. Let's add the aliasing enum values for
the type-C AUX CHs.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-5-ville.syrjala@linux.intel.com

drm/i915: Give DDI encoders even better names

Let's pimp the DDI encoder->name to reflect what the spec calls them.
Ie. on pre-tgl DDI A-F, on tgl+ DDI A-C or DDI TC1-6.

Also since each encoder is really a combination of the DDI and the PHY
we include the PHY name as well.

ICL is a bit special since it already has the two different types
of DDIs (combo or TC) but it still calls them just DDI A-F regarless
of the type. For that let's add an extra "(TC)" note to remind
is which type of DDI it really is.

The code is darn ugly, but not sure there's much we can do about it.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-4-ville.syrjala@linux.intel.com

drm/i915: Add PORT_TCn aliases to enum port

Since tgl the DDIs have been named A,B,C,TC1,TC2,TC3...
Add the appropriate enum values for the TC DDIs to enum port.

v2: Deal with rkl and dg1

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-3-ville.syrjala@linux.intel.com

drm/i915: s/PORT_TC/TC_PORT_/

Make the namespacing for enum tc_port better by adding
the TC_ to the actual enum values.

v2: Drop the extra TC (Lucas)

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-2-ville.syrjala@linux.intel.com

drm/i915: Use _MMIO_PIPE3() for ilk+ WM0_PIPE registers

Remove the hand rolled array of WM0_PIPE register offsets
and use the standard _MMIO_PIPE3() instead.

v2: Take care of gvt too

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212211738.27770-1-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>

drm/i915: Remove unused variable ret

This patch fixes below warnings reported by coccicheck

./drivers/gpu/drm/i915/i915_debugfs.c:789:5-8: Unneeded variable: "ret". Return "0" on line 1012

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1603937925-53176-1-git-send-email-zou_wei@huawei.com

drm/i915: Fix encoder lookup during PSR atomic check

The atomic check hooks must look up the encoder to be used with a
connector from the connector's atomic state, and not assume that it's
the connector's current attached encoder. The latter one can change
under the atomic check func, or can be unset yet as in the case of MST
connectors.

This fixes
[    7.940719] Oops: 0000 [#1] SMP NOPTI
[    7.944407] CPU: 2 PID: 143 Comm: kworker/2:2 Not tainted 5.6.0-1023-oem #23-Ubuntu
[    7.952102] Hardware name: Dell Inc. Latitude 7320/, BIOS 88.87.11 09/07/2020
[    7.959278] Workqueue: events output_poll_execute [drm_kms_helper]
[    7.965511] RIP: 0010:intel_psr_atomic_check+0x37/0xa0 [i915]
[    7.971327] Code: 80 2d 06 00 00 20 74 42 80 b8 34 71 00 00 00 74 39 48 8b 72 08 48 85 f6 74 30 80 b8 f8 71 00 00 00 74 27 4c 8b 87 80 04 00 00 <41> 8b 78 78 83 ff 08 77 19 31 c9 83 ff 05 77 19 48 81 c1 20 01 00
[    7.977541] input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input5
[    7.990154] RSP: 0018:ffffb864c073fac8 EFLAGS: 00010202
[    7.990155] RAX: ffff8c5d55ce0000 RBX: ffff8c5d54519000 RCX: 0000000000000000
[    7.990155] RDX: ffff8c5d55cb30c0 RSI: ffff8c5d89a0c800 RDI: ffff8c5d55fcf800
[    7.990156] RBP: ffffb864c073fac8 R08: 0000000000000000 R09: ffff8c5d55d9f3a0
[    7.990156] R10: ffff8c5d55cb30c0 R11: 0000000000000009 R12: ffff8c5d55fcf800
[    7.990156] R13: ffff8c5d55cb30c0 R14: ffff8c5d56989cc0 R15: ffff8c5d56989cc0
[    7.990158] FS:  0000000000000000(0000) GS:ffff8c5d8e480000(0000) knlGS:0000000000000000
[    8.047193] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    8.052970] CR2: 0000000000000078 CR3: 0000000856500005 CR4: 0000000000760ee0
[    8.060137] PKRU: 55555554
[    8.062867] Call Trace:
[    8.065361]  intel_digital_connector_atomic_check+0x53/0x130 [i915]
[    8.071703]  intel_dp_mst_atomic_check+0x5b/0x200 [i915]
[    8.077074]  drm_atomic_helper_check_modeset+0x1db/0x790 [drm_kms_helper]
[    8.083942]  intel_atomic_check+0x92/0xc50 [i915]
[    8.088705]  ? drm_plane_check_pixel_format+0x4f/0xb0 [drm]
[    8.094345]  ? drm_atomic_plane_check+0x7a/0x3a0 [drm]
[    8.099548]  drm_atomic_check_only+0x2b1/0x450 [drm]
[    8.104573]  drm_atomic_commit+0x18/0x50 [drm]
[    8.109070]  drm_client_modeset_commit_atomic+0x1c9/0x200 [drm]
[    8.115056]  drm_client_modeset_commit_force+0x55/0x160 [drm]
[    8.120866]  drm_fb_helper_restore_fbdev_mode_unlocked+0x54/0xb0 [drm_kms_helper]
[    8.128415]  drm_fb_helper_set_par+0x34/0x50 [drm_kms_helper]
[    8.134225]  drm_fb_helper_hotplug_event.part.0+0xb4/0xe0 [drm_kms_helper]
[    8.141150]  drm_fb_helper_hotplug_event+0x1c/0x30 [drm_kms_helper]
[    8.147481]  intel_fbdev_output_poll_changed+0x6f/0xa0 [i915]
[    8.153287]  drm_kms_helper_hotplug_event+0x2c/0x40 [drm_kms_helper]
[    8.159709]  output_poll_execute+0x1aa/0x1c0 [drm_kms_helper]
[    8.165506]  process_one_work+0x1e8/0x3b0
[    8.169561]  worker_thread+0x4d/0x400
[    8.173249]  kthread+0x104/0x140
[    8.176515]  ? process_one_work+0x3b0/0x3b0
[    8.180726]  ? kthread_park+0x90/0x90
[    8.184416]  ret_from_fork+0x1f/0x40

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2361
References: https://gitlab.freedesktop.org/drm/intel/-/issues/2486
Reported-by: William Tseng <william.tseng@intel.com>
Reported-by: Cooper Chiou <cooper.chiou@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201027160928.3665377-1-imre.deak@intel.com

drm/i915/display: remove debug message from error path

First check in the function is if swsci() is supported. All the error
paths are easy to figure out the reason, so remove the extra debug
message: it's normal not to support swsci() e.g. in dgfx.

v2: Rather than special case dgfx, just remove the debug message
    (from Ville)

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201027044618.719064-2-lucas.demarchi@intel.com

drm/i915: Guard debugfs against invalid access without display

Do not create the display debugfs files when we don't have display.

Based on previous patch by José Souza.

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201027044618.719064-1-lucas.demarchi@intel.com

drm/i915/dg1: invert HPD pins

HPD pins are inverted for DG1 platform.

Bspec: 49956
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021082034.3170478-3-lucas.demarchi@intel.com

drm/i915/dg1: add hpd interrupt handling

DG1 has one more combo phy port, no TC and all irq handling goes through
SDE, like for MCC.

v2: Also change intel_hpd_pin_default() to include DG1 mapping
v3, v4: Rebase on hpd refactor

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021082034.3170478-2-lucas.demarchi@intel.com

drm/i915/tgl/psr: Fix glitches when doing frontbuffer modifications

Writes to CURSURFLIVE in TGL are causing IOMMU errors and visual
glitches that are often reproduced when executing CPU intensive
workloads while a eDP 4K panel is attached.

Manually exiting PSR causes the frontbuffer to be updated without
glitches and the IOMMU errors are also gone but this comes at the cost
of less time with PSR active.

So using this workaround until this issue is root caused and a better
fix is found.

The current code is already ready to enable PSR after this exit if
there is not other frontbuffer modifications.

Adding a new if block in psr_force_hw_tracking_exit() instead of reuse
the else/gen8- block because the plan is to revert this workaround
as soon as a better solution is found.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002231627.24528-1-jose.souza@intel.com

drm/i915: Reset the interrupt mask on disabling interrupts

As we disable the interrupt during suspend, also reset the irq_mask to
short-circuit subsystems that later try to turn off their interrupt
source.

<4>[  101.816730] i915 0000:00:02.0: drm_WARN_ON(!intel_irqs_enabled(dev_priv))
<4>[  101.816853] WARNING: CPU: 3 PID: 4241 at drivers/gpu/drm/i915/i915_irq.c:343 ilk_update_display_irq+0xb3/0x130 [i915]

v2: Reset irq_mask for i8xx_irq_reset as well, and split patch to focus
on only i915->irq_mask

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201022114246.28566-1-chris@chris-wilson.co.uk

drm/i915/display: Unkerneldoc cnl_program_nearest_filter_coefs

The block comment for cnl_program_nearest_filter_coefs() has a wonderful
diagram, but although it is marked up as kerneldoc does not use the
markup for providing the function definition.

drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'dev_priv' not described in 'cnl_program_nearest_filter_coefs'
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'pipe' not described in 'cnl_program_nearest_filter_coefs'
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'id' not described in 'cnl_program_nearest_filter_coefs'
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'set' not described in 'cnl_program_nearest_filter_coefs'

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021185649.17759-1-chris@chris-wilson.co.uk

drm/i915: Reject 90/270 degree rotated initial fbs

We don't currently handle the initial fb readout correctly
for 90/270 degree rotated scanout. Reject it.

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020194330.28568-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Clean up the irq enable/disable for ilk rps

Let's unmask the PCU event irq _after_ we've set up the
hardware and software to deal with the fallout. We can
also drop the PCU event bit from DEIER except when we
need it for rps.

And on the disable side we replace the hand rolled (and
unlocked) DEIER/IIR/IMR frobbing with ilk_disable_display_irq().
Ocd does require me to reorder it to be symmetric with
the enable path however.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021131443.25616-5-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Do gen5_gt_irq_postinstall() before enabling the master interrupt

Let's make sure the lower level interrupt bits are all lined
up before we flip on the master interrupt.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021131443.25616-4-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Fix potential overflows in ilk ips calculations

A bunch of the ips calculations require 64bit math. In particular
'corr' and 'corr2' look like they can overflow on 32bit systems.
Switch to explicit u64 for those.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021131443.25616-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Read actual GPU frequency from MEMSTAT_ILK on ILK

There is no GEN6_RPSTAT1 on ILK. Instead of reading that let's
try to get the same information from MEMSTAT_ILK. At least it
seems to track MEMSWCTL frequency request perfectly on my ILK.
It needs the same invert trick as the request value.

We don't want to put the invert thing into intel_gpu_freq()
and intel_freq_opcode() because that would incorrectly invert
the min/max/etc frequencies also.

One day someone might want to reverse engineer the formula for
converting these numbers to Hz, but for now we'll just report
them raw.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021131443.25616-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Restore ILK-M RPS support

Restore RPS for ILK-M. We lost it when an extra HAS_RPS()
check appeared in intel_rps_enable().

Unfortunaltey this just makes the performance worse on my
ILK because intel_ips insists on limiting the GPU freq to
the minimum. If we don't do the RPS init then intel_ips will
not limit the frequency for whatever reason. Either it can't
get at some required information and thus makes wrong decisions,
or we mess up some weights/etc. and cause it to make the wrong
decisions when RPS init has been done, or the entire thing is
just wrong. Would require a bunch of reverse engineering to
figure out what's going on.

Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 9c878557b1eb ("drm/i915/gt: Use the RPM config register to determine clk frequencies")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021131443.25616-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Enable scaling filter for plane and CRTC

GEN >= 10 hardware supports the programmable scaler filter.

Attach scaling filter property for CRTC and plane for GEN >= 10
hardwares and program scaler filter based on the selected filter
type.

changes since v3:
* None
changes since v2:
* Use updated functions
* Add ps_ctrl var to contain the full PS_CTRL register value (Ville)
* Duplicate the scaling filter in crtc and plane hw state (Ville)
changes since v1:
* None
Changes since RFC:
* Enable properties for GEN >= 10 platforms (Ville)
* Do not round off the crtc co-ordinate (Danial Stone, Ville)
* Add new functions to handle scaling filter setup (Ville)
* Remove coefficient set 0 hardcoding.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-5-pankaj.laxminarayan.bharadiya@intel.com

drm/i915/display: Add Nearest-neighbor based integer scaling support

Integer scaling (IS) is a nearest-neighbor upscaling technique that
simply scales up the existing pixels by an integer
(i.e., whole number) multiplier.Nearest-neighbor (NN) interpolation
works by filling in the missing color values in the upscaled image
with that of the coordinate-mapped nearest source pixel value.

Both IS and NN preserve the clarity of the original image. Integer
scaling is particularly useful for pixel art games that rely on
sharp, blocky images to deliver their distinctive look.

Introduce functions to configure the scaler filter coefficients to
enable nearest-neighbor filtering.

Bspec: 49247

changes since v6:
* Trust compiler, remove pointless inline keyword from cnl_coef_tap()
  & cnl_nearest_filter_coef() functions (Ville)
changes since v4:
* Make cnl_coef_tap(), cnl_nearest_filter_coef() inline (Uma)
changes since v3:
* None
changes since v2:
* Move APIs from 5/5 into this patch.
* Change filter programming related function names to cnl_*, move
  filter select bits related code into inline function (Ville)
changes since v1:
* Rearrange skl_scaler_setup_nearest_neighbor_filter() to iterate the
  registers directly instead of the phases and taps (Ville)

changes since RFC:
* Refine the skl_scaler_setup_nearest_neighbor_filter() logic (Ville)

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-4-pankaj.laxminarayan.bharadiya@intel.com

drm/i915: Introduce scaling filter related registers and bit fields

Introduce scaler registers and bit fields needed to configure the
scaling filter in prgrammed mode and configure scaling filter
coefficients.

changes since v3:
* None
changes since v2:
* Change macro names to CNL_* and  use +(set)*8 instead of adding
  another trip through _PICK_EVEN (Ville).
changes since v1:
* None
changes since RFC:
* Parametrize scaler coeffient macros by 'set' (Ville)

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-3-pankaj.laxminarayan.bharadiya@intel.com

drm: Introduce plane and CRTC scaling filter properties

Introduce per-plane and per-CRTC scaling filter properties to allow
userspace to select the driver's default scaling filter or
Nearest-neighbor(NN) filter for upscaling operations on CRTC and
plane.

Drivers can set up this property for a plane by calling
drm_plane_create_scaling_filter() and for a CRTC by calling
drm_crtc_create_scaling_filter().

NN filter works by filling in the missing color values in the upscaled
image with that of the coordinate-mapped nearest source pixel value.

NN filter for integer multiple scaling can be particularly useful for
for pixel art games that rely on sharp, blocky images to deliver their
distinctive look.

changes since: v6:
* Move property doc to existing "Standard CRTC Properties" and
  "Plane Composition Properties" doc comments (Simon)
changes since v3:
* Refactor code, add new function for common code (Ville)
changes since v2:
* Create per-plane and per-CRTC scaling filter property (Ville)
changes since v1:
* None
changes since RFC:
* Add separate properties for plane and CRTC (Ville)

Link: https://github.com/xbmc/xbmc/pull/18194
Link: https://github.com/xbmc/xbmc/pull/18567
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Simon Ser <contact@emersion.fr>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-2-pankaj.laxminarayan.bharadiya@intel.com

drm/i915/display: Rename pipe_timings to transcoder_timings

No functional changes in this patch.

With Bigjoiner, there are 2 pipes driving 2 halfs of 1
transcoder. The transcoder_mode has the full timings, and is used
for configuring the transcoder with the intended mode after
joining the 2 halves.
To clear the confusion, we rename intel_set_pipe_timings to
intel_set_transcoder_timings

v2:
* Split the renaming into separate patch (Ville)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008214535.22942-2-manasi.d.navare@intel.com

drm/i915: Sort ICL PCI IDs

Sort the ICL PCI IDs numerically. Some order seems better than
randomness.

Cc: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-14-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Sort CNL PCI IDs

Sort the CNL PCI IDs numerically. Some order seems better than
randomness.

Cc: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-13-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Sort CFL PCI IDs

Sort the CFL PCI IDs numerically. Some order seems better than
randomness.

Cc: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-12-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Sort CML PCI IDs

Sort the CML PCI IDs numerically. Some order seems better than
randomness.

Cc: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-11-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Sort KBL PCI IDs

Sort the KBL PCI IDs numerically. Some order seems better than
randomness.

Cc: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-10-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Sort SKL PCI IDs

Sort the SKL PCI IDs numerically. Some order seems better than
randomness.

Cc: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-9-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Sort HSW PCI IDs

Sort the HSW PCI IDs numerically. Some order seems better than
randomness.

Cc: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-8-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Ocd the HSW PCI ID hex numbers

Most of the HSW PCI IDs are upper case hex numbers, but a
few are lower case. Make it consistent so these don't
stick out like a sore thumb.

Cc: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-7-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Try to fix the SKL GT3/4 vs. GT3e/4e comments

Bunch of the SKL SKUs currently documented as GT3/4 seem to actually
be GT3e/4e. Fix up the comments.

Cc: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-6-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Add SKL GT1.5 PCI IDs

Add three new devices 0x1913, 0x1915, and 0x1917 also known as
iSKLULTGT15, iSKLULXGT15, and iSKLDTGT15.

Signed-off-by: Alexei Podtelezhnikov <apodtele@gmail.com>
[vsyrjala: Split separate changes into separate patchs,
           Sort the IDs]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-5-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Reclassify SKL 0x1923 and 0x1927 as ULT

Reclassify 0x1923, 0x1927 according to specifications. Of note,
the second to last digit seems to correspond to GT#.

Signed-off-by: Alexei Podtelezhnikov <apodtele@gmail.com>
[vsyrjala: Split separate changes into separate patches,
           Sort the IDs]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-4-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Reclassify SKL 0x192a as GT3

Reclassify 0x192A according to specifications. Of note, the
second to last digit seems to correspond to GT#.

Signed-off-by: Alexei Podtelezhnikov <apodtele@gmail.com>
[vsyrjala: Split separate changes into separate patches]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-3-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Update Haswell PCI IDs

Reclassify 0x0426 as GT3 (GT2+) according to specifications and the second
least significant digit.

Signed-off-by: Alexei Podtelezhnikov <apodtele@gmail.com>
[vsyrjala: s/GT2/GT3/ in the comment]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716172106.2656-2-ville.syrjala@linux.intel.com
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>

drm/i915: Sort the mess around ICP TC hotplugs regs

Move the DSC stuff out from the middle of the ICP HPD register
definitions. The location seems to have been selected by a
dice roll.

SHPD_FILTER_CNT addition also went astray due to the DSC
mess, so we also fix that vs. ICP_TC_HPD_{SHORT,LONG}_DETECT().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006143349.5561-2-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>

drm/i915: Refactor .hpd_irq_setup() calls a bit

Add a small wrapper for .hpd_irq_setup() which does the
"do we even have the hook?" and "are display interrupts enabled?"
checks.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006185809.4655-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Reorder hpd init vs. display resume

Currently we call .hpd_irq_setup() directly just before display
resume, and follow it with another call via intel_hpd_init()
just afterwards. Assuming the hpd pins are marked as enabled
during the open-coded call these two things do exactly the
same thing (ie. enable HPD interrupts). Which even makes sense
since we definitely need working HPD interrupts for MST sideband
during the display resume.

So let's nuke the open-coded call and move the intel_hpd_init()
call earlier. However we need to leave the poll_init_work stuff
behind after the display resume as that will trigger display
detection while we're resuming. We don't want that trampling over
the display resume process. To make this a bit more symmetric
we turn this into a intel_hpd_poll_{enable,disable}() pair.
So we end up with the following transformation:
intel_hpd_poll_init() -> intel_hpd_poll_enable()
lone intel_hpd_init() -> intel_hpd_init()+intel_hpd_poll_disable()
.hpd_irq_setup()+resume+intel_hpd_init() -> intel_hpd_init()+resume+intel_hpd_poll_disable()

If we really would like to prevent all *long* HPD processing during
display resume we'd need some kind of software mechanism to simply
ignore all long HPDs. Currently we appear to have that just for
fbdev via ifbdev->hpd_suspended. Since we aren't exploding left and
right all the time I guess that's mostly sufficient.

For a bit of history on this, we first got a mechanism to block
hotplug processing during suspend in commit 15239099d7a7 ("drm/i915:
enable irqs earlier when resuming") on account of moving the irq enable
earlier. This then got removed in commit 50c3dc970a09 ("drm/fb-helper:
Fix hpd vs. initial config races") because the fdev initial config
got pushed to a later point. The second ad-hoc hpd_irq_setup() for
resume was added in commit 0e32b39ceed6 ("drm/i915: add DP 1.2 MST
support (v0.7)") to be able to do MST sideband during the resume.
And finally we got a partial resurrection of the hpd blocking
mechanism in commit e8a8fedd57fd ("drm/i915: Block fbdev HPD
processing during suspend"), but this time it only prevent fbdev
from handling hpd while resuming.

v2: Leave the poll_init_work behind
v3: Remove the extra intel_hpd_poll_disable() from display reset (Lyude)
    Add the missing intel_hpd_poll_disable() to display init (Imre)

Cc: Lyude Paul <lyude@redhat.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013181137.30560-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>

drm/i915: s/intel_dp_sink_dpms/intel_dp_set_power/

Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.

Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.

Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Move the lspcon resume from .reset() to intel_dp_sink_dpms()

Rather that try to trick LSPCON back into PCON mode from the .reset()
hook let's just do that as a regular part of the normal modeset
sequence, which is going to take care of the system resume case. During
a normal modeset this should normally be a nop as the mode should have
already been switched by .detect().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Drop runtime-pm assert from vgpu io accessors

The "mmio" writes into vgpu registers are simple memory traps from the
guest into the host. We do not need to assert in the guest that the
device is awake for the io as we do not write to the device itself.

However, over time we have refactored all the mmio accessors with the
result that the vgpu reuses the gen2 accessors and so inherits the
assert for runtime-pm of the native device. The assert though has
actually been there since commit 3be0bf5acca6 ("drm/i915: Create vGPU
specific MMIO operations to reduce traps").

References: 3be0bf5acca6 ("drm/i915: Create vGPU specific MMIO operations to reduce traps")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Yan Zhao <yan.y.zhao@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200811092532.13753-1-chris@chris-wilson.co.uk

drm/i915: Force VT'd workarounds when running as a guest OS

If i915.ko is being used as a passthrough device, it does not know if
the host is using intel_iommu. Mixing the iommu and gfx causes a few
issues (such as scanout overfetch) which we need to workaround inside
the driver, so if we detect we are running under a hypervisor, also
assume the device access is being virtualised.

Reported-by: Stefan Fritsch <sf@sfritsch.de>
Suggested-by: Stefan Fritsch <sf@sfritsch.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Stefan Fritsch <sf@sfritsch.de>
Cc: stable@vger.kernel.org
Tested-by: Stefan Fritsch <sf@sfritsch.de>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019101523.4145-1-chris@chris-wilson.co.uk

drm/i915/display/fbc: Implement WA 22010751166

Underruns happens when plane height + y offset is not a modulo of 4
when FBC is enabled. It happens when scanline is at vactive - 10 but
that is not feasible to do from the software side so here completely
disabling FBC when height + y offset matches to avoid visual glitches.

Specification says that it only affects TGL display C stepping and
newer but to simply the check and as TGL is already in final costumers
hands, pre-production display stepping A and B was also included.

BSpec: 52887 ICL
BSpec: 52888 EHL/JSL
BSpec: 52890/55378 TGL
BSpec: 53508 DG1
BSpec: 53273 RKL
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019175609.28715-1-jose.souza@intel.com

drm/i915/display: Program DBUF_CTL tracker state service

This sequence is not part of "Sequences to Initialize Display" but
as noted in the MBus page the DBUF_CTL.Tracker_state_service needs
to be set to 8.

BSpec: 49213
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019173906.18892-1-jose.souza@intel.com

drm/i915: Inline intel_dp_ycbcr420_config()

intel_dp_ycbcr420_config() is rather pointless. Just inline it
directly into intel_dp_compute_config(). This gets rid of the
ugly double assignment of output_format.

Not really sure what the best policy would be when the user
supplies a mode classified by the display as "YCbCr 4:2:0
only", but we know that we can't do YCbCr 4:2:0 output. For
now keep the current behaviour of just silently upgrade
it to RGB 4:4:4.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-3-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>

drm/i915: Nuke lspcon_ycbcr420_config()

Remove the lspcon special case from intel_dp_compute_config() and
just treat it like any other DFP than can do 4:4:4->4:2:0 conversion.

The only difference between the two codepaths was that the lspcon
code tried to already halve port_clock. That was just total nonsense
as we hadn't even computed the base port_clock at that time.
All that stuff happens intel_dp_compute_link_config*() and it
already takes care of the 4:2:0 clock reduction.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-2-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>

drm/i915: Nuke lspcon_downsampling

crtc_state->lspcon_downsampling isn't particularly useful at
the moment since we can't even do proper readout for it.
Let's get rid of it. Will help with unifying the LSPCON with
the regular DFP YCbCr output support.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>

drm/i915: Mark initial fb obj as WT on eLLC machines to avoid rcu lockup during fbdev init

Currently we leave the cache_level of the initial fb obj
set to NONE. This means on eLLC machines the first pin_to_display()
will try to switch it to WT which requires a vma unbind+bind.
If that happens during the fbdev initialization rcu does not
seem operational which causes the unbind to get stuck. To
most appearances this looks like a dead machine on boot.

Avoid the unbind by already marking the object cache_level
as WT when creating it. We still do an excplicit ggtt pin
which will rewrite the PTEs anyway, so they will match whatever
cache level we set.

Cc: <stable@vger.kernel.org> # v5.7+
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2381
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007120329.17076-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Apply WAC6entrylatency to kbl/cfl

WAC6entrylatency is trying to fix excessive rc6 entry latency caused
by the extra delay from FBC_LLC_READ_CTRL, which is there for some
extra sync with uncore for frame buffer caching in LLC.

Reading through the hsd the recommendation was to set the FBC_LLC_FULLY_OPEN
bit to disable this extra delay entirely. This can be done whenever fb LLC
caching is not used. The alternative suggestion was to reduce the delay to
eg. 0x5 via updated BIOS programming instructions. But all the kbl/cfl
machines I've seen still have the default 0xff programmed. As we never use
fb LLC caching let's just apply the w/a to all skl derivatives to get
consistent rc6 latencies.

I was able to measure the effect of FBC_LLC_READ_CTRL to rc6 latency
via forcewake. Here's a graph of some of the results:

             sleep;fw_req=1;wait fw_ack==1;sleep;fw_req=0;wait fw_ack==0
 fw_ack==1 duration
    160us +----------------------------------------------------------------+
          |          +          +        $$+         +          +          |
          |  $$           $    $   ******$$ **   $ $**$*  #########$$######|
    140us |-$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$*$$$$$$$$$$$$$$$$ $$$$$$|
          | $                     *                       #                |
          | $                     *                       #                |
    120us |$+                     *                       #              +-|
          |$                      *                       #                |
          |$                      *                  #   #                 |
    100us |$+         ************########################               +-|
          |$          *          *#                                        |
          |$      *****   #########                                        |
     80us |$+     *    # ####   ##                                       +-|
          |$   **** ### # #                                                |
          |  ** ####                     FBC_LLC_READ_CTRL: 0x8000 ******* |
     60us |-######                       FBC_LLC_READ_CTRL: 0xffff #######-|
          |##        +          +    FBC_LLC_READ_CTRL: 0x400000ff $$$$$$$ |
          +----------------------------------------------------------------+
         0ms       10ms       20ms       30ms      40ms       50ms       60ms
                                   sleep duration

The default FBC_LLC_READ_CTRL value of 0xff is documented to give us
a 170usec delay. That tracks well with the knees at 0xffff->~44msec and
0x8000->~22msec we see in the graph.

We can see that if we sleep longer than the FBC_LLC_READ_CTRL delay
we always observe the full (~145usec) rc6 wakeup latency. But if we sleep
for less than the FBC_LLC_READ_CTRL delay we see a quicker fw wakeup,
presumably due the hardware not having yet entered rc6 fully.
The other plateaus in the graph I suspect correspond to some shallower
internal rc states.

v2: s/usec/msec/ typo in commit msg

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716190426.17047-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/rkl: Add new cdclk table

A recent bspec update has provided a new cdclk table for RKL.  All of
the cdclk values are the same as those we've been using on ICL, TGL,
etc., but we obtain them by doubling both the PLL ratio and CD2X divider
numbers.

Bspec: 49202
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201015220038.271740-1-matthew.d.roper@intel.com

drm/i915/dgfx: define llc and snooping behaviour

While we do lack the faster shared LLC, we should still have support
for snooping over PCIe.

Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-11-lucas.demarchi@intel.com

drm/i915/dg1: Update DMC_DEBUG register

Update the DMC_DEBUG_DC5 register to its new location and do not try
reading the DC6 counter since DG1 doesn't support DC6.

v2: Use IS_DGFX() instead of IS_DG1(). Even if not having DC6 is not
directly related to DGFX, the register move to a new location is. So in
future, if there is one supporting DC6, it would just need to add the
other register rather than fixing the case of a wrong register being
read (Matt)

Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-10-lucas.demarchi@intel.com

drm/i915/dg1: DG1 does not support DC6

DC6 is not supported on DG1, so change the allowed DC mask for DG1.
This is not yet on bspec, but it has been confirmed by HW engineers.

Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-9-lucas.demarchi@intel.com

drm/i915/dg1: Add initial DG1 workarounds

DG1 shares some workarounds with TGL and RKL and also has some
additional workarounds of its own.

v2: Correct location of Wa_1408615072 (JohnH).
v3: Apply WAs 1606700617, 18011464164 and 22010931296 to DG1 (José)
v4 (Anusha)
  - Add Wa_22010271021
  - s/Wa_14010096844/Wa_1409836686
v5:
  - Extend Wa_14010919138 to all revs (Matt Atwood)
  - Power gate media is global gen12 design. (Rodrigo)
  - Rebase (Lucas)
v6: use REG_BIT() to fix checkpatch warning (Lucas)

BSpec: 53508

Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-8-lucas.demarchi@intel.com

drm/i915/dg1: Load DMC

Add support to load DMC v2.0.2 on DG1

While we're at it, make TGL use the same GEN12 firmware size definition
and remove obsolete comment.

Bpec: 49230

v2: do not replace GEN12_CSR_MAX_FW_SIZE (from José)
    and replace stale comment

Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-7-lucas.demarchi@intel.com

drm/i915/dg1: Enable DPLL for DG1

Add DG1 DPLL Enable register macro and use the macro to enable the
correct DPLL based on PLL id. Although we use
_MG_PLL1_ENABLE/_MG_PLL2_ENABLE these are rather combo phys.

While at it, fix coding style: wrong newlines and use if/else chain

v2: Rewrite original patch from Aditya Swarup based on refactors
upstream

Bspec: 49443, 49206

Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Aditya Swarup <aditya.swarup@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-6-lucas.demarchi@intel.com

drm/i915/dg1: Add and setup DPLLs for DG1

Add entries for dg1 plls and setup dg1_pll_mgr to reuse ICL callbacks.
Initial setup for shared dplls DPLL0/1 for DDIA/DDIB and DPLL2/3 for
DDI-TC1/DDI-TC2. Configure dpll cfgcrx registers to drive the plls on
DG1.

v2 (Lucas): Reword commit message and add missing update_ref_clks hook
   (requested by Matt Roper)

Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-5-lucas.demarchi@intel.com

drm/i915/dg1: Add DPLL macros for DG1

DG1 has 4 DPLLs where DPLL0 and DPLL1 drive DDIA/B and
DPLL2 and DPLL3 drive DDI-TC1/DDI-TC2.

Introduce DG1_DPLL_CFCRx() helper macros to configure
DPLL registers.

Bspec: 50288, 50299

Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-4-lucas.demarchi@intel.com

drm/i915/dg1: Add DG1 power wells

TGL power wells can be re-used for DG1 with the exception of the fake
power well for TC_COLD.

v2: use logic to skip power wells while copying instead of duplicating
the definition of TGL power wells (Matt Roper)

Bspec: 49182

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-3-lucas.demarchi@intel.com

drm/i915/cnl: skip PW_DDI_F on certain skus

The skus guarded by IS_CNL_WITH_PORT_F() have port F and thus they need
those power wells. The others don't have those. Up to now we were
just overriding the number of power wells on !IS_CNL_WITH_PORT_F(),
relying on those power wells to be the last ones. Now that we have logic
in place to skip power wells by id, use it instead.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-2-lucas.demarchi@intel.com

drm/i915/display: allow to skip certain power wells

This allows us to skip power wells on a platform allowing it to re-use
the table from another one instead of having to create a new table from
scratch that is basically a copy with a few removals.

Cc: Imre Deak <imre.deak@intel.com>
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
[ Adapt ignore logic to be based on pw id rather than adding a new
  field, as suggested by Imre ]
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-1-lucas.demarchi@intel.com

drm/i915/jsl: Split EHL/JSL platform info and PCI ids

Recently we came across requirement to identify EHL and JSL
platform to program them differently. Thus Split the basic
platform definition, macros, and PCI IDs to differentiate
between EHL and JSL platforms. Also, IS_ELKHARTLAKE is replaced
with IS_JSL_EHL everywhere.

Changes since V1 :
- Rebased to avoid merge conflicts
- Added missed check for jasperlake in intel_uc_fw.c

Cc : Matt Roper <matthew.d.roper@intel.com>
Cc : Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013192948.63470-1-tejaskumarx.surendrakumar.upadhyay@intel.com

drm/i915: Force DPCD backlight mode for BOE 2270 panel

BOE 2270 panel failed to control backlight brightness.
Add it in edid quirks to force using DPCD backlight control.
Then the brightness can be controlled.

Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009085750.88490-2-aaron.ma@canonical.com

drm/i915/dpcd_bl: uncheck PWM_PIN_CAP when detect eDP backlight capabilities

BOE panel with ID 2270 claims both PWM_PIN_CAP and AUX_SET_CAP backlight
control bits, but default chip backlight failed to control brightness.

Check AUX_SET_CAP and proceed to check quirks or VBT backlight type.
DPCD can control the brightness of this pannel.

Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009085750.88490-1-aaron.ma@canonical.com

drm/i915/dp: Tweak initial dpcd backlight.enabled value

In commit 79946723092b ("drm/i915: Assume 100% brightness when not in
DPCD control mode"), we fixed the brightness level when DPCD control was
not active to max brightness. This is as good as we can guess since most
backlights go on full when uncontrolled.

However in doing so we changed the semantics of the initial
'backlight.enabled' value. At least on Pixelbooks, they  were relying
on the brightness level in DP_EDP_BACKLIGHT_BRIGHTNESS_MSB to be 0 on
boot such that enabled would be false. This causes the device to be
enabled when the brightness is set. Without this, brightness control
doesn't work. So by changing brightness to max, we also flipped enabled
to be true on boot.

To fix this, make enabled a function of brightness and backlight control
mechanism.

Fixes: 79946723092b ("drm/i915: Assume 100% brightness when not in DPCD control mode")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Kevin Chowski <chowski@chromium.org>>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200918002845.32766-1-sean@poorly.run

drm/i915: Switch to LTTPR non-transparent mode link training

The DP Standard's recommendation is to use the LTTPR non-transparent
mode link training if LTTPRs are detected, so let's do this.

Besides power-saving, the advantages of this are that the maximum number
of LTTPRs can only be used in non-transparent mode (the limit is 5-8 in
transparent mode), and it provides a way to narrow down the reason for a
link training failure to a given link segment. Non-transparent mode is
probably also the mode that was tested the most by the industry.

The changes in this patchset:
- Pass the DP PHY that is currently link trained to all LT helpers, so
  that these can access the correct LTTPR/DPRX DPCD registers.
- During LT take into account the LTTPR common lane rate/count and the
  per LTTPR-PHY vswing/pre-emph limits.
- Switch to LTTPR non-transparent LT mode and train each link segment
  according to the sequence in DP Standard v2.0 (complete CR/EQ for
  each segment before continuing with the next segment).

v2:
- Switch to non-transparent mode during connector detection, which is
  required before reading the per-PHY LTTPR capabilities.
- Move the DP_PHY_LTTPR() macro to drm_dp_helper.h (Ville)
- Use the new drm_dp_dpcd_read_phy_link_status() instead of adding the
  same logic to intel_dp_get_link_status(). (Ville)
- Make intel_dp_lttpr_phy_caps() return a pointer to the whole array
  instead of a pointer to its first element. (Ville)
- Add the intel_dp_phy_is_downstream_of_source() helper. (Ville)
- Add a code comment about the disable->enable quirk of
  non-transparent mode.
- Add the intel_dp_training_pattern_set_reg() helper.
- Fix checkpatch/sparse warns.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-7-imre.deak@intel.com

drm/i915: Switch to LTTPR transparent mode link training

By default LTTPRs should be in transparent link training mode,
nevertheless in this patch we switch to this default mode explicitly.

The DP Standard recommends this, supposedly because an LTTPR may be left
in the non-transparent mode (by BIOS, previous kernel, or after reset
due to a firmware bug). I haven't seen this happening, but let's follow
the DP Standard.

v2:
- Add a code comment about the explicit disabling of non-transparent
  mode.
v3:
- Move check to prevent initing LTTPRs on eDP to init_dp_lttpr_init().

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-6-imre.deak@intel.com

drm/dp: Add LTTPR helpers

Add the helpers and register definitions needed to read out the common
and per-PHY LTTPR capabilities and perform link training in the LTTPR
non-transparent mode.

v2:
- Add drm_dp_dpcd_read_phy_link_status() and DP_PHY_LTTPR() here instead
  of adding these to i915. (Ville)
v3:
- Use memmove() to convert LTTPR to DPRX link status format. (Ville)

Cc: dri-devel@lists.freedesktop.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-5-imre.deak@intel.com

drm/i915: Factor out a helper to disable the DPCD training pattern

To prepare for a follow-up LTTPR change factor out a helper to disable
the training pattern in DPCD. We'll need to do this for each LTTPR
(without programming the port to output the idle pattern) when training
in LTTPR non-transparent mode.

While at it also move the disable-link-training logic from
intel_dp_set_link_train() to intel_dp_stop_link_train(), since the
latter is the only user of this.

v2:
- Move the disable-link-training logic to intel_dp_stop_link_train()
  (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-4-imre.deak@intel.com

drm/i915: Simplify the link training functions

Split the prepare, link training, fallback-handling steps into their own
functions for clarity and as a preparation for the upcoming LTTPR
changes.

While at it also:
- Unexport and inline intel_dp_set_idle_link_train(), which is used at a
  single place.
- Add some documentation to functions that are exported or that can use
  a better description about which part of the LT sequence they
  implement.

v2: (Ville)
- Unexport/inline intel_dp_set_idle_link_train()
- Make the documentation of
  intel_dp_prepare_link_train()/intel_dp_stop_link_train() more accurate
  wrt. HW specific details.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-3-imre.deak@intel.com

drm/i915: Fix DP link training pattern mask

An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.

Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.

v2:
- Use a helper instead of open-coding the masking. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com

drm/i915: Update gen12 multicast register ranges

The updated bspec forcewake table also provides us with new multicast
ranges that should be reflected in our workaround code.

Note that there are different types of multicast registers with
different styles of replication and different steering registers.  The
i915 MCR range lists we're updating here are only used to ensure we can
verify workarounds properly (i.e., if we can't steer register reads we
don't want to verify workarounds where an unsteered read might hit a
fused-off instance of the unit).  Because of this, we don't need to
include any of the multicast ranges where all instances of the register
will always present and fusing doesn't play a role.  Specifically, that
means that we are not including the MCR ranges designated as "SQIDI" in
the bspec.

Bspec: 66696
Cc: Caz Yokoyama <caz.yokoyama@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009194442.3668677-4-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Update gen12 forcewake table

The bspec's forcewake page was very stale and out of date for recent
platforms.  The hardware team finally provided us with an updated gen12
table (which applies to TGL, RKL, and DG1) and there are a lot of
changes.

v2:
 - Add comments showing the subregions of ranges that we've combined for
   ease of code review.  (Jose)
 - Rebase on the s/FORCEWAKE_BLITTER/FORCEWAKE_GT/ patch

Bspec: 66696
Cc: Caz Yokoyama <caz.yokoyama@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009194442.3668677-3-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Rename FORCEWAKE_BLITTER to FORCEWAKE_GT

The power well that we've been referring to as the 'blitter' well is
actually more of a general GT power well which contains a lot of things
other than the blitter engine registers.  The FORCEWAKE_BLITTER name in
the code was used for historic reasons, but no longer matches how the
bspec describes this power well and just causes confusion for people not
familiar with this area of the code.  Let's rename it to FORCEWAKE_GT to
more accurately describe the role of the power well and match how the
modern bspec refers to it.

v2:
 - Add a comment noting that the GT power well includes the blitter
   engine. (Jose)

Bspec: 66696, 66534, 67609
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009194442.3668677-2-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915/display: Program PSR2 selective fetch registers

Another step towards PSR2 selective fetch, here programming plane
selective fetch registers and MAN_TRK_CTL enabling selective fetch but
for now it is fetching the whole area of the planes.
The damaged area calculation will come as next and final step.

v2:
- removed warn on when no plane is visible in state
- removed calculations using plane damaged area in
intel_psr2_program_plane_sel_fetch()

v3:
- do not shift 16 positions the plane dst coordinates, only src is
shifted

v4:
- only setting PLANE_SEL_FETCH_CTL_ENABLE and MCURSOR_MODE in
PLANE_SEL_FETCH_CTL

v5:
- not masking bits for cursor

BSpec: 55229
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007195238.53955-3-jose.souza@intel.com

drm/i915/display: Check PSR parameter and flag only in state compute phase

Due to the debugfs flag, has_psr2 in CRTC state could have a different
value than psr.psr2_enabled and it was causing PSR2 subfeatures(DC3CO
and selective fetch) to be set to not a expected state.

So here only taking in consideration the parameter and debugfs flag
when computing PSR state, this way the CRTC state will also have
the correct state.

intel_psr_fastset_force() was already broken as
intel_psr_compute_config() was already only enabling PSR when
psr_global_enabled() and all other PSR requirements are met.
So some changes was required in this function, now it iterates over
all connectors, if it is a eDP connector and is active force a modeset
in the CRTC driving this connector, what will cause the new PSR state
to be set based on the debugfs flag.

v2:
- end connector iterator in error cases

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007195238.53955-2-jose.souza@intel.com

drm/i915/display: Ignore IGNORE_PSR2_HW_TRACKING for platforms without sel fetch

For platforms without selective fetch this register is reserved so
do not write 0 to it.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007195238.53955-1-jose.souza@intel.com

drm/i915/vbt: Add VRR VBT toggle

This will be used in future but already adding to VBT so we are
updated with VBT changes.

Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008211932.24989-3-jose.souza@intel.com

drm/i915/vbt: Update the version and expected size of BDB_GENERAL_DEFINITIONS map

This will remove the "Expected child device config size for VBT
version 235 not known" debug message seen in TGL, although this is not
fixing anything it good to keep our VBT parser updated.

Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008211932.24989-2-jose.souza@intel.com

drm/i915/vbt: Fix backlight parsing for VBT 234+

Child min_brightness is obsolete from VBT 234+, instead the new
min_brightness field in the main structure should be used.

This new field is 16 bits wide, so backlight_precision_bits is needed
to check if value needs to be scaled down but it is only available in
VBT 236+ so working around it by using the also new backlight_level
in the main struct.

v2:
- missed that backlight_data->level is also obsolete

v3:
- s/backlight/brightness to better match specification
- using u16 to specify brightness level instead of a u32 : 16

BSpec: 20149
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008211932.24989-1-jose.souza@intel.com

drm/i915: s/int/u32/ for aux_offset/alignment

ggtt offsets/alignments are u32 everywhere else. Don't use
a signed int for them here.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008101608.8652-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Skip aux plane stuff when there is no aux plane

when the hardware isn't going to use the aux plane there's no
real point in dealing with the relevant hardware restrictions.
So let's just skip all that when not necessary.

We can now also remove the offset=~0xfff behaviour for unused
color planes. Let's just zero out everyting so as to not leave
stale garbage behind to confuse people debugging the code.

v2: Explicitly set AUX_DIST to zero when there is no aux plane

Reviewed-by: Imre Deak <imre.deak@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009120028.32422-1-ville.syrjala@linux.intel.com

drm/i915: Set all unused color plane offsets to ~0xfff again

When the number of potential color planes grew to 4 we stopped
setting all unused color plane offsets to ~0xfff. The code
still tries to do this, but actually does nothing since the
loop limits are bogus.

skl_check_main_surface() actually depends on this ~0xfff
behaviour as it will make sure to move the main surface
offset below the aux surface offset because the hardware
AUX_DIST must be a non-negative value [1], and for simplicity
it doesn't bother checking if the AUX plane is actually
needed or not. So currently it may end up shuffling the
main surface around based on some stale leftover AUX offset.

The skl+ plane code also just blindly calculates the AUX_DIST
whether or not the AUX plane is actually needed by the hw or
not, and that too will now potentially use some stale AUX
surface offset in the calculation. Would seem nicer to
guarantee a consistent non-negative AUX_DIST always.

So bring back the original ~0xfff offset behaviour for
unused color planes. Though it doesn't seem super likely
that this inconsistency would cause any real issues.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Fixes: 2dfbf9d2873a ("drm/i915/tgl: Gen-12 display can decompress surfaces compressed by the media engine")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008101608.8652-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Rename i915_{save,restore}_state()

i915_{save,restore}_state() are actually all about the display.
Currently they are split into display part + SWF part. But since
the SWF part is also related to the display let's just move that
part into its own thing and flip the roles around so that the
current display part is the main function.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005171441.26612-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Wait for VLV/CHV/BXT/GLK DSI panel power cycle delay on reboot

As with eDP and LVDS we should also respect the power cycle
delay on DSI panels. We are not using the power sequencer
for these, and we have no optimizations around the sleep
duration, so we just msleep() the whole thing away.

Note that the ICL+ DSI code doesn't seem to have any power
off/power cycle delay handling whatsoever. The only thing it
handles is the power on delay. As that looks pretty busted
in general I won't bother dealing with it for the time being.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Wait for LVDS panel power cycle delay on reboot

Just like with eDP let's wait for the power sequencer power
cycle delay before we reboot the machine, as otherwise we
can't guarantee the panel's minimum power cycle delay will
be respected.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Wait for eDP panel power cycle delay on reboot on all platforms

Extend the eDP panel power cycle delay wait on reboot handling
to cover all platforms. No reason to think that VLV/CHV are
in any way special since the documentation states that the
hardware power cycle delay goes back to its default value on
reset, and that may not be enough for all panels.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>