drm/i915: Mask page table errors on gen2/3 with FBC

FBC on gen2/3 seems to trigger page table errors. No visual
artifacts are visible, and essentially the same FBC
code works on gen4 so these seem entirely spurious. There
are also hints in gen3 bspec indicating that certain bits
in PGTBL_ER are just not wired up correctly in the
hardware.

Ideally we'd want to mask out only the bogus bits, but
sadly there is no mask for PGTBL_ER, and instead we are
forced to mask out all page table errors via EMR :(

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125185234.21599-6-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>

drm/i915: Extract {i9xx,i965)_error_mask()

Pull the EMR calculation into small helpers.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125185234.21599-5-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>

drm/i915: Dump PGTBL_ER on gen2/3/4 error interrupt

PGTBL_ER contains the individual reasons for the page table
error interrupt. Dump it out.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125185234.21599-4-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>

drm/i915: Undo rmw damage to gen3 error interrupt handler

The gen2/gen3 irq code is supposed to be identical apart
from the 32bit vs. 16bit access width. The recent change
to intel_de_rmw() ruined that symmetry. Restore it to avoid
needless mental gymnastics when comparing the two codepaths.

And while at it remove the extra eir!=0 check that somehow
ended up in the gen2 codepath only.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125185234.21599-3-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>

drm/i915: Mark FIFO underrun disabled earlier

At least on some platforms (tested on ctg) the way
vgacon does screen blanking seems to flag constant
FIFO underruns, which means we have to be prepared
for them while the driver is loading. Currently
there is a time window between drm_crtc_init() and
intel_sanitize_fifo_underrun_reporting() during
which FIFO underrun reporting is in fact marked as
enabled. Thus we may end up mistakenly detecting
these bogus underruns during driver init.

Close the race by marking FIFO underrun reporting
as disabled prior to even registering the crtc.
intel_sanitize_fifo_underrun_reporting()/etc. will
re-enable it later if needed.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125185234.21599-2-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>

drm/i915/audio: Track audio state per-transcoder

The audio logic lives in the transcoder rather than the pipe,
so start tracking it like that.

This is only really important for bigjoiner cases where tracking
by pipe doesn't work at all since intel_audio_codec_{enable,disable}()
won't even be called for the slave pipe. This means the state
checker won't find the ELD for the slave pipe and gets upset.
The PD->has_audio readout does currently work since that gets
read out from the same transcoder for both pipes.

For other cases this doesn't actually matter since it's only
the normal pipe transcoders that are audio capable, whereas
the more special transcoders (EDP/DSI) are not.

v2: Fix kernel docs

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230222151454.24888-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8222

drm/i915/display/power: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230217111836.864959-1-andrzej.hajda@intel.com

drm/i915: Remove pointless register read

We just wrote the EDP transcoder's VTOTAL register a few lines
earlier, so instead of reading it back out again let's just
generate the same value for the transocder B/C register.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Sprinkle some FIXMEs about TGL+ DSI transcoder timing mess

The DSI code has some local hacks to program TRANS_VBLANK on
TGL+ (ICL DSI transcoders didn't have this register). That
will not work when we need to start using the delayed vblank
(for DSB purposes). Too lazy to figure out what the is going
on there, so just sprinkle FIXMEs in the hopes someone else
will spot them eventually.

v2: Only TRANS_{HBLANK,SET_CONTEXT_LATENCY} still no not
    exist for DSI transcoders, only TRANS_VBLANK

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-12-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Configure TRANS_SET_CONTEXT_LATENCY correctly on ADL+

On TGL VBLANK.VBLANK_START was the mechanism by which we can
delay the pipe's internal vblank in relation to the transcoder's
vblank. On ADL+ that no longer does anything. Instead we must
now use the new TRANS_SET_CONTEXT_LATENCY register. Program it
accordingly.

And since VBLANK.VBLANK_START is no longer used by the hardware
on ADL+ let's just zero it out to make it stand out in register
dumps. Seeing the zeroed value should hopefully remind people
to check the other register instead.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-11-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/dsb: Skip DSB command buffer setup if we have no LUTs

If we have no LUTs to load there is no point in setting up
the DSB command buffer.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-9-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/dsb: Nuke the DSB debug

We'll be wanting to start the DSB from the vblank evasion critical
section so printk()s are a big nono. Get rid of the debug print.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-8-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/dsb: Allow vblank synchronized DSB execution

Allow the caller to ask for the DSB commands to execute
during vblank.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-7-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/dsb: Define more DSB registers

Add definitions for more DSB registers. Less annoying spec
trawling when working on the DSB code.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-2-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/psr: Stop clobbering TRANS_SET_CONTEXT_LATENCY

The PSR code has no business mucking around with the
vblank delay. Currently nothing that depends on knowing
the exact vblank start scanline (eg. vblank evasion)
is aware of this and so will not work correctly.

The w/a seems to be for pre-production hw only, so let's
just nuke it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Define transcoder timing register bitmasks

Define the contents of the transcoder timing registers using
REG_GENMASK() & co. For ease of maintenance let's just define
the bitmasks with the full 16bit width (also used by the
current hand rolled stuff) even though not all bits are actually
used. None of the unsued bits have ever contained anything.

Jani spotted that the CRT load detection code did use narrower
bitmasks, so that is now going to change. But that is fine
since any garbage in the high bits would have been caught by
the state checker that always used the full 16bit masks.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Add local adjusted_mode variable

Clean up the eyesore in intel_get_transcoder_timings() a
bit by adding a local 'adjusted_mode' variable.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Define the "unmodified vblank" interrupt bit

On TGL+ the normal "start of vblank" interrupt is the pipe's
(potentially delayed) version. Add the new bit for the
transcoder's "unmodified" vblank so I don't have to dig it
out from bspec every time.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Dump blanking start/end

With the delayed vblank we need to start knowing where
the blanking periods start. So let's start dumping
out also the blanking start/end timings.

And while at it let's try to make that huge list of
numbers somewhat legible by indicating what each value
means. Also drop the 'type' since that doesn't really
mean anything for the crtc_ timings.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: s/PIPECONF/TRANSCONF/

Rename PIPECONF to TRANSCONF to make it clear what it actually
applies to.

While the usual convention is to pick the earliers name I think
in this case it's more clear to use the later name. Especially
as even the register offset is in the wrong range (0x70000 vs.
0x60000) and thus makes it look like this is per-pipe.

There is one place in gvt that's doing something with TRANSCONF
while iterating with for_each_pipe(). So that might not be doing
the right thing for TRANSCODER_EDP, dunno. Not knowing what it
does I left it as is to avoid breakage.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Give CPU transcoder timing registers TRANS_ prefix

Name the CPU transcoder timing registers TRANS_FOO rather than
just FOO. This is the modern name, after the pipe/transcoder split
happened. Makes it a bit more obvious whether you pass in a pipe or
a transcoder.

PIPESRC is a bit special as it's a pipe register, even though it
lives in the transcoder registers range (0x60000 instead of 0x70000).

And BCLRPAT I suppose is a transcoder register (since it has something
to do with the timing generator), but it doesn't even exist after gen4
so I left it to use the only name it ever had in bspec.

And while at it let's pass in the correct enum in few more
places why don't we. Although in all those places the distinction
doesn't matter.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Flatten intel_ddi_{enable,disable}_transcoder_clock()

Use an early return to get rid of the extra indentation level
in intel_ddi_{enable,disable}_transcoder_clock().

Also unify the platform handling in between the two while at
it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Rename intel_ddi_{enable,disable}_pipe_clock()

What intel_ddi_{enable,disable}_pipe_clock() actually do is
enable the clock to the transcoder, not the pipe. Rename
accordingly.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix platform default aux ch for skl

SKL/derivatives have DDI E but no AUX E, so we need to pick
another aux ch as the platform default. DDI E is more or less
the other half of DDI A, so we pick AUX A.

In all other cases we should have a corresponding aux ch for
each DDI.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216231312.32664-3-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>

drm/i915: Pimp encoder ddc_pin/aux_ch debug messages

Use encoder->name rather than port_name() in the debug messages
so that they actually make more sense.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216231312.32664-2-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>

drm/i915: Restructure intel_bios_port_aux_ch()

Restructure intel_bios_port_aux_ch() to resemble the ddc_pin
counterpart, where the intel_bios.c stuff only deals with the
child device definition, and the platform default will come from
elsewhere.

This requires the introduction of AUX_CH_NONE as the value 0
is already taken to mean AUX_CH_A.

v2: Sort includes alphabetically (Ankit)
vCould we ask them to do a BIOS fix for all of them so that
we wouldn't keep getting these bug reports for each model
separately?

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216231312.32664-1-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>

drm/i915/hwmon: Enable PL1 limit when writing limit value to HW

Previous documentation suggested that the PL1 power limit is always enabled
in HW. However we now find this not to be the case on some platforms (such
as ATSM). Therefore enable the PL1 power limit (by setting the enable bit)
when writing the PL1 limit value to HW.

Bspec: 51864

Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216164944.2366150-3-ashutosh.dixit@intel.com

drm/i915/hwmon: Replace hwm_field_scale_and_write with hwm_power_max_write

hwm_field_scale_and_write has a single caller hwm_power_write and is
specific to hwm_power_write but makes it appear that it is a general
function which can have multiple callers. Replace the function with
hwm_power_max_write which is specific to hwm_power_write and use that in
future patches where the function needs to be extended.

Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216164944.2366150-2-ashutosh.dixit@intel.com

drm/i915: Use encoder->devdata more

Switch a lot of the intel_bios_foo() stuff to just accept the
devdata (VBT child device info) directly, instead of taking
detours via vbt.ports[].

Also unify the function naming scheme.

v2: Drop the redundant "encoder" from the dp/hdmi specific functions

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216000425.32216-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Add a few more debugs for failed framebuffer creation

Most of the .fb_create() failure paths are annotated but there
are a few that seem capable of failing silently (well, higher
level code should print something, just not anything actually
useful). Drop a few more hints into the log to aid in debugging.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215222426.26085-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>

drm/i915: Don't leak the DPT if drm_framebuffer_init() fails

We are failing to free the already allocated DPT if the final
drm_framebuffer_init() fails. That would require idr_alloc() to
fail, so not very likely, but let's add the cleanup code anyway.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215222426.26085-1-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>

drm/i915: Reduce ELD hex dumps a bit

Do the ELD hexdumps only up to the last differing byte.
The rest is typically all zeroes anyway so not much point
in dumping it.

Couldn't find anything for memcmp_diff_len() so
rolled my own.

v2: Use semantics and function name suggested by Jani

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215150129.13288-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Include connector id+name in all backlight debugs/errors

With multi panel machines becoming more prominent it's also
important to know which connector's backlight we're talking
about. Include that information in all the backlight debug/error
messages.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215140021.2843-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/quirks: Add inverted backlight quirk for HP 14-r206nv

This laptop uses inverted backlight PWM. Thus, without this quirk,
backlight brightness decreases as the brightness value increases and
vice versa.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8013
Cc: stable@vger.kernel.org
Signed-off-by: Mavroudis Chatzilaridis <mavchatz@protonmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230201184947.8835-1-mavchatz@protonmail.com

drm/i915/display/misc: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230110113656.4050491-1-andrzej.hajda@intel.com

drm/i915/display/interfaces: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105131046.2173431-8-andrzej.hajda@intel.com

drm/i915/display/panel: use intel_de_rmw if possible in panel related code

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105131046.2173431-7-andrzej.hajda@intel.com

drm/i915/display/hdmi: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105131046.2173431-6-andrzej.hajda@intel.com

drm/i915/display/pch: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105131046.2173431-5-andrzej.hajda@intel.com

drm/i915/display/phys: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105131046.2173431-4-andrzej.hajda@intel.com

drm/i915/display/dpll: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105131046.2173431-3-andrzej.hajda@intel.com

drm/i915/display/core: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105131046.2173431-1-andrzej.hajda@intel.com

drm/i915/wm: remove ILK+ nop funcs fallback

Disabling ILK+ watermarks on failure to read the watermark levels dates
back to 2010 and commit 7f8a85698f5c ("drm/i915: Add the support of
memory self-refresh on Ironlake"), with no explanations, and it's been
copied and modified from that ever since. Finally drop it.

If the value are actually zero, the ilk_compute_*_wm() functions should
handle it gracefully.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215141910.433043-5-jani.nikula@intel.com

drm/i915: rename intel_pm_types.h -> display/intel_wm_types.h

The file was never really about pm types, and now it's even more
obvious. Move under display as intel_wm_types.h.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215141910.433043-4-jani.nikula@intel.com

drm/i915/wm: move watermark debugfs to intel_wm.c

Follow the new convention of placing debugfs with the code.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215141910.433043-3-jani.nikula@intel.com

drm/i915/wm: warn about ilk_wm_sanitize() on display ver 9+

The sanitization should be limited to PCH split platforms up to display
version 8. Warn and bail out otherwise.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215141910.433043-2-jani.nikula@intel.com

drm/i915/wm: move ILK watermark sanitization to i9xx_wm.[ch]

Move sanitize_watermarks() to i9xx_wm.[ch] and rename as
ilk_wm_sanitize(). The slightly unfortunate downside is having to expose
intel_atomic_check() from intel_display.c, but this declutters
intel_display.c nicely.

v2:
- Move to i9xx_wm.[ch] instead of intel_wm.[ch] (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215141910.433043-1-jani.nikula@intel.com

drm/i915: Copy highest enabled wm level to disabled wm levels for gen >= 9

There was a specific SW workaround requested, which should prevent
some watermark issues happening, which requires copying highest
enabled wm level to those disabled wm levels(bit 31 is of course
still needs to be cleared).
This is related to different subsystems like PSR and others, which
may still consult a low power wm values ocassionally, despite those
are disabled. For that reason we need to keep sane values in
correspondent registers, even when those are disabled.

HSDES: 22016115093

v2: Remove redundant WA for ICL and extend this WA for all platforms
    starting from SKL, as it seems that we needed this anyway on
    all of those(Ville Syrjälä)

Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213164453.5782-1-stanislav.lisovskiy@intel.com

drm/i915/display: Add 480 MHz CDCLK steps for RPL-U

A new step of 480MHz has been added on SKUs that have a RPL-U
device id to support 120Hz displays more efficiently. Use a
new quirk to identify the machine for which this change needs
to be applied.

v2: (Matt)
    - Add missing clock steps
    - Correct reference clock typo

v3: - Revert to RPL-U subplatform (Jani)

v4: - Remove Bspec reference from code (Jani)

Bspec: 55409
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130100806.1373883-3-chaitanya.kumar.borah@intel.com

drm/i915: Add RPL-U sub platform

Separate out RPLU device ids and add them to both RPL and
newly created RPL-U subplatforms.

v2: (Matt)
    - Sort PCI-IDs numerically
    - Name the sub-platform to accurately depict what it is for
    - Make RPL-U part of RPL subplatform

v3: revert to RPL-U subplatform (Jani)

v4: (Jani)
    - Add RPL-U ids to RPL-P platform
    - Remove redundant comment

Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130100806.1373883-2-chaitanya.kumar.borah@intel.com

drm/i915: Clean up g4x+ sprite TILEOFF programming

We defined the bitmasks for DVSTILEOFF but never used them.
Remedy that.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230214134739.25077-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Don't hide function calls with side effects

Hiding a function call with side effects inside the
variable declaration block is a bit rude. Make it
stand out more.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230214134739.25077-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Make backlight setup debugs consistent

It's confusing to debug backlight issues when one can't
easily even tell what kind of backlight control was
selected. Sprinkle uniform debug messages to all the
backlight setup functions.

Also the one that was already there (ext_pwm) was
using drm_info() for some reason. I don't think that's
warranted so switch it to drm_dbg_kms() as well.

v2: Deal with AUX backlights too (Jani)
    Move the VLV/CHV initial pipe debug there too (Jani)

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215135616.30411-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/wm: add .get_hw_state to watermark funcs

Get rid of the if ladder in intel_modeset_setup_hw_state() and hide a
number of functions by adding a .get_hw_state() hook to watermark
functions. At least for now, combine the platform specific sanitization
to the hw state readouts on the relevant platforms instead of adding a
separate hook for that.

There's a functional change on PCH split platforms: If i9xx_wm_init()
fails to read plane latency and chooses the nop functions,
ilk_wm_get_hw_state() won't get called for readout. Add the
ilk_init_lp_watermarks() call on that path which now won't be called in
.get_hw_state(), as it looks like the only thing that could make a
difference.

v2:
- Add missing static (kernel test robot)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6da32831e40606cc8b90491b83196917f2ce36ab.1676317696.git.jani.nikula@intel.com

drm/i915/wm: move functions to call watermark hooks to intel_wm.[ch]

Move the wrappers to call watermark hooks into intel_wm.[ch]. This
declutters intel_display.c nicely.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2c8243c5c81b8cd8e34d51f55f3533373c305d0e.1676317696.git.jani.nikula@intel.com

drm/i915/wm: move remaining watermark code out of intel_pm.c

Add new files intel_wm.[ch] and i9xx_wm.[ch] under display/ to hold
generic and pre-SKL watermark code, respectively. SKL+ watermark code
has already been split out to skl_watermark.[ch].

Use the _wm.[ch] naming for brevity; we may want to rename
skl_watermark.[ch] later accordingly.

Add new intel_wm_init() to call either skl_wm_init() or
i9xx_wm_init(i915) depending on the platform, the latter comprising of
the remains of intel_init_pm().

Sprinkle in some minor checkpatch fixes while moving the code.

v2:
- Rebase
- Fix copyright year

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ddf04a07a37f0368b3fef85d4ebb924082fec6cd.1676317696.git.jani.nikula@intel.com

drm/i915: move memory frequency detection to intel_dram.c

The memory frequency detection is a bit spread out here and
there. Consolidate to intel_dram.c.

v2:
- Remove inaccurate comment (Ville)
- Call detect_mem_freq() unconditionally (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8a862eeca8b42a98e04b3c52637851d33531abb6.1676317696.git.jani.nikula@intel.com

drm/i915: Sanitize the display fused-off check on GEN7/8

Detecting in intel_device_info_runtime_init() that the display is fused
off or not present should only zero intel_runtime_info::pipe_mask, while
the other related masks will be accordingly zeroed later in the
function. Remove the redundant zeroing of the related fields on GEN7/8.

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208114300.3123934-5-imre.deak@intel.com

drm/i915/dgfx, mtl+: Disable display functionality if the display is not present

DG1/DG2 and MTL+ has added a new display-present HW flag. Check this
flag and if cleared, disable the driver's display functionality.

So far the missing check resulted in running the display initialization
sequence, and the WARNs below, due to the display register accesses
timing out:

[    3.902843] ------------[ cut here ]------------
[    3.902848] i915 0000:03:00.0: drm_WARN_ON(intel_de_wait_for_set(dev_priv, ((const i915_reg_t){ .reg = (0x42000) }), (1 << (27 - (pg))), 1))
[    3.902879] WARNING: CPU: 6 PID: 462 at drivers/gpu/drm/i915/display/intel_display_power_well.c:326 gen9_wait_for_power_well_fuses+0x71/0x80 [i915]
[    3.903009] Modules linked in: hid_sensor_hub intel_ishtp_hid i915(+) rtsx_pci_sdmmc drm_buddy mmc_core drm_display_helper crct10dif_pclmul nvme cec crc32_pclmul intel_ish_ipc crc32c_intel ucsi_acpi hid_multitouch nvme_core ghash_clmulni_intel typec_ucsi rtsx_pci ttm sha512_ssse3 serio_raw intel_ishtp typec video i2c_hid_acpi i2c_hid wmi pinctrl_tigerlake ip6_tables ip_tables x_tables fuse
[    3.903021] CPU: 6 PID: 462 Comm: systemd-udevd Tainted: G     U             6.2.0-rc6+ #50
[    3.903023] Hardware name: LENOVO 82VB/LNVNB161216, BIOS KMCN09WW 04/26/2022
[    3.903023] RIP: 0010:gen9_wait_for_power_well_fuses+0x71/0x80 [i915]
[    3.903105] Code: 48 8b 5f 50 48 85 db 75 03 48 8b 1f e8 98 bb 0d e9 48 c7 c1 00 65 a1 c0 48 89 da 48 c7 c7 4b c5 a3 c0 48 89 c6 e8 e3 df 53 e9 <0f> 0b 5b c3 cc cc cc cc 0f 1f 80 00 00 00 00 90 90 90 90 90 90 90
[    3.903106] RSP: 0018:ffffa7cec0b07a98 EFLAGS: 00010292
[    3.903107] RAX: 0000000000000080 RBX: ffff9a05430eaaa0 RCX: 0000000000000000
[    3.903108] RDX: 0000000000000001 RSI: ffffffffaa7ab69e RDI: 00000000ffffffff
[    3.903108] RBP: ffff9a0552ba2020 R08: ffffffffab062ce0 R09: 00000000abd3ffc2
[    3.903109] R10: ffffffffffffffff R11: 0000000000000081 R12: 0000000000000000
[    3.903109] R13: ffff9a05532a9cb0 R14: ffffffffc09e1670 R15: ffff9a0543132000
[    3.903110] FS:  00007f24d0fe5b40(0000) GS:ffff9a0ccf780000(0000) knlGS:0000000000000000
[    3.903110] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    3.903111] CR2: 00005643d7a31a28 CR3: 0000000111614002 CR4: 0000000000770ee0
[    3.903112] PKRU: 55555554
[    3.903112] Call Trace:
[    3.903113]  <TASK>
[    3.903114]  hsw_power_well_enable+0x12f/0x1a0 [i915]
[    3.903191]  intel_power_well_enable+0x21/0x70 [i915]
[    3.903265]  icl_display_core_init+0x92/0x6a0 [i915]
[    3.903346]  intel_power_domains_init_hw+0x1da/0x5b0 [i915]
[    3.903422]  intel_modeset_init_noirq+0x60/0x250 [i915]
[    3.903497]  i915_driver_probe+0x562/0xe10 [i915]
[    3.903557]  ? i915_pci_probe+0x87/0x180 [i915]
[    3.903617]  local_pci_probe+0x3e/0x80
[    3.903621]  pci_device_probe+0xb3/0x210
[    3.903622]  really_probe+0xdb/0x380
[    3.903624]  ? pm_runtime_barrier+0x50/0x90
[    3.903626]  __driver_probe_device+0x78/0x170
[    3.903627]  driver_probe_device+0x1f/0x90
[    3.903628]  __driver_attach+0xce/0x1c0
[    3.903629]  ? __pfx___driver_attach+0x10/0x10
[    3.903630]  bus_for_each_dev+0x5f/0x90
[    3.903631]  bus_add_driver+0x1ae/0x200
[    3.903632]  driver_register+0x89/0xe0
[    3.903634]  i915_init+0x1f/0x7f [i915]
[    3.903695]  ? __pfx_init_module+0x10/0x10 [i915]
[    3.903751]  do_one_initcall+0x43/0x220
[    3.903753]  ? kmalloc_trace+0x26/0x90
[    3.903756]  do_init_module+0x4a/0x200
[    3.903758]  __do_sys_init_module+0x157/0x180
[    3.903760]  do_syscall_64+0x58/0xc0
[    3.903762]  ? do_syscall_64+0x67/0xc0
[    3.903762]  ? exc_page_fault+0x70/0x170
[    3.903764]  entry_SYSCALL_64_after_hwframe+0x72/0xdc

Bspec: 49189, 53112

v2: (Jani)
- Change "Display fused off" dmesg info to "Display not present".
- Zero only runtime->pipe_mask, other fields being zeroed based on this
  later.
- Detect display presence already before the fused-off checks and only for
  HAS_DISPLAY().
v3: Fix "preset" vs "present" typo.

Reported-and-tested-by: iczero <iczero@hellomouse.net>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8015
Cc: iczero <iczero@hellomouse.net>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208114300.3123934-4-imre.deak@intel.com

drm/i915: Move display power initialization during driver probing later

Determining whether the display engine is present on a platform happens
only in intel_device_info_runtime_init(). Initializing the display power
functionality depends on this condition, so move
intel_power_domains_init() later after the runtime init function has
been called.

The next patch fixing platforms without display, depends on this patch.

Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208114300.3123934-3-imre.deak@intel.com

drm/i915: Fix system suspend without fbdev being initialized

If fbdev is not initialized for some reason - in practice on platforms
without display - suspending fbdev should be skipped during system
suspend, fix this up. While at it add an assert that suspending fbdev
only happens with the display present.

This fixes the following:

[   91.227923] PM: suspend entry (s2idle)
[   91.254598] Filesystems sync: 0.025 seconds
[   91.270518] Freezing user space processes
[   91.272266] Freezing user space processes completed (elapsed 0.001 seconds)
[   91.272686] OOM killer disabled.
[   91.272872] Freezing remaining freezable tasks
[   91.274295] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[   91.659622] BUG: kernel NULL pointer dereference, address: 00000000000001c8
[   91.659981] #PF: supervisor write access in kernel mode
[   91.660252] #PF: error_code(0x0002) - not-present page
[   91.660511] PGD 0 P4D 0
[   91.660647] Oops: 0002 [#1] PREEMPT SMP NOPTI
[   91.660875] CPU: 4 PID: 917 Comm: bash Not tainted 6.2.0-rc7+ #54
[   91.661185] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS edk2-20221117gitfff6d81270b5-9.fc37 unknown
[   91.661680] RIP: 0010:mutex_lock+0x19/0x30
[   91.661914] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 53 48 89 fb e8 62 d3 ff ff 31 c0 65 48 8b 14 25 00 15 03 00 <f0> 48 0f b1 13 75 06 5b c3 cc cc cc cc 48 89 df 5b eb b4 0f 1f 40
[   91.662840] RSP: 0018:ffffa1e8011ffc08 EFLAGS: 00010246
[   91.663087] RAX: 0000000000000000 RBX: 00000000000001c8 RCX: 0000000000000000
[   91.663440] RDX: ffff8be455eb0000 RSI: 0000000000000001 RDI: 00000000000001c8
[   91.663802] RBP: ffff8be459440000 R08: ffff8be459441f08 R09: ffffffff8e1432c0
[   91.664167] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
[   91.664532] R13: 00000000000001c8 R14: 0000000000000000 R15: ffff8be442f4fb20
[   91.664905] FS:  00007f28ffc16740(0000) GS:ffff8be4bb900000(0000) knlGS:0000000000000000
[   91.665334] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   91.665626] CR2: 00000000000001c8 CR3: 0000000114926006 CR4: 0000000000770ee0
[   91.665988] PKRU: 55555554
[   91.666131] Call Trace:
[   91.666265]  <TASK>
[   91.666381]  intel_fbdev_set_suspend+0x97/0x1b0 [i915]
[   91.666738]  i915_drm_suspend+0xb9/0x100 [i915]
[   91.667029]  pci_pm_suspend+0x78/0x170
[   91.667234]  ? __pfx_pci_pm_suspend+0x10/0x10
[   91.667461]  dpm_run_callback+0x47/0x150
[   91.667673]  __device_suspend+0x10a/0x4e0
[   91.667880]  dpm_suspend+0x134/0x270
[   91.668069]  dpm_suspend_start+0x79/0x80
[   91.668272]  suspend_devices_and_enter+0x11b/0x890
[   91.668526]  pm_suspend.cold+0x270/0x2fc
[   91.668737]  state_store+0x46/0x90
[   91.668916]  kernfs_fop_write_iter+0x11b/0x200
[   91.669153]  vfs_write+0x1e1/0x3a0
[   91.669336]  ksys_write+0x53/0xd0
[   91.669510]  do_syscall_64+0x58/0xc0
[   91.669699]  ? syscall_exit_to_user_mode_prepare+0x18e/0x1c0
[   91.669980]  ? syscall_exit_to_user_mode_prepare+0x18e/0x1c0
[   91.670278]  ? syscall_exit_to_user_mode+0x17/0x40
[   91.670524]  ? do_syscall_64+0x67/0xc0
[   91.670717]  ? __irq_exit_rcu+0x3d/0x140
[   91.670931]  entry_SYSCALL_64_after_hwframe+0x72/0xdc
[   91.671202] RIP: 0033:0x7f28ffd14284

v2: CC stable. (Jani)

Fixes: f8cc091e0530 ("drm/i915/fbdev: suspend HPD before fbdev unregistration")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/8015
Reported-and-tested-by: iczero <iczero@hellomouse.net>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: iczero <iczero@hellomouse.net>
Cc: <stable@vger.kernel.org> # v6.1+
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208114300.3123934-2-imre.deak@intel.com

drm/i915: Use encoder->devdata in eDP init

Since we now populate encoder->devdata for all DP capable
platforms we can consult it directly during the eDP
connector init instead of taking a detour via some global
list/array.

Unfortunately we can't quite get rid of
intel_dp_is_port_edp() since it's still used by the higher
level ilk/vlv/chv output setup code.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Iterate all child devs in intel_bios_is_port_present()

Instead of consulting vbt.ports[] lets just go through the
whole child device list to check whether a specific port
was declared by the VBT or not.

Note that this doesn't change anything wrt. detecting duplicate
child devices with the same port as vbt.ports[] would also always
contain exactly one of the duplicates.

v2: Include a is_port_valid() check to deal with some broken VBTs
    Mention something about duplicate port detection (Jani)

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230214073818.20231-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Pass devdata to intel_bios_port_aux_ch()

Currently intel_bios_port_aux_ch() digs out the devdata
(VBT child device info) from the vbt.ports[] array. We
need to get rid of that, so just pass in the correct
encoder->devdata (now that we have it also for g4x+ ports)
directly.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Populate encoder->devdata for g4x+ DP/HDMI ports

Let's make encoder->devdata (the VBT information for the port)
available on g4x+ platforms as well. Much easier when you can
just grab it there instead of trying to find it from some global
list array based on the port.

Note that (unlike DDI platforms) we don't currently require
that each DP/HDMI port is actually declared in VBT. Perhaps
in the future we may want to rethink that, but for now just
stick in a debug+FIXME as a reminder.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Consult the registered encoders for the ICL combo PHY w/a

Display WA #1178 calls us to tweak some magic bits when doing AUX
to an external combo PHY port. Instead of looking to see if the VBT
has declared such a port (which could in theory even alias with a
declared eDP port on the same PHY) just check the real situation
based on the registered encoders.

The only slight chicken vs. egg situation here is during output
probing. But typically we'd register the eDP ports first and so
once we get to probe anything external on the combo PHY we have
already determined if it's eDP or not.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Replace intel_bios_is_port_hpd_inverted() with intel_bios_encoder_hpd_invert()

intel_bios_is_port_hpd_inverted() is only used on bxt/glk on
which we always have encoder->devdata available. So consult
that instead of digging around in vbt.ports[].

And rename the function to match the common pattern.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Replace intel_bios_is_lane_reversal_needed() with intel_bios_encoder_lane_reversal()

The sole user of intel_bios_is_lane_reversal_needed() has
the devdata already located, so pass it in directly instead
of digging it again from vbt.ports[].

And rename the function to follow the common pattern for
these things.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Replace intel_bios_is_lspcon_present() with intel_bios_encoder_is_lspcon()

We always have encoder->devdata available on the platforms
that can have LSPCON. So let's start looking there instead
of digging it out from vbt.ports[].

And let's rename the function to fit the common pattern
for these things.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Move variables to loop context

Lot of the loops over VBT child devices have variables
declared outside the loop but only used inside the loop.
Move the variables to a tighter scope.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Pass the whole encoder to hotplug_enables()

bxt_hotplug_enables() needs to dig out not only the
hpd_pin but also the VBT child device info, so let's just
pass in the whole encoder to avoid having to look things
up multiple times.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/dp: Increase slice_height for DP

According VDSC spec 1.2a Section 3.8 Options for Slice
implies that 108 lines is an optimal slice height, but any
size can be used as long as vertical active
integer multiple and maximum vertical slice count requirements are met.

Bspec: 49259

--v3
-remove previous fallback code and return slice_height as 2 [Jani]

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230214052017.3312044-1-suraj.kandpal@intel.com

drm/i915: Prefix hex numbers with 0x

It's hard to figure out whether the number is hex
or decimal if doesn't have the 0x to indicate hex.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130181701.29977-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Include stepping information in device info dump

Dump the stepping information alongside all the other device
info. Might avoid some guesswork when reading logs.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130181701.29977-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/display: Pass drm_i915_private as param to i915 funcs

For i915 functions pass struct drm_i915_private directly instead of
struct drm_device.

v2: Use to_i915(dev) directly without alias(Andrzej).

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125095603.17845-1-nirmoy.das@intel.com

drm/i915: Replace wm.max_levels with wm.num_levels and use it everywhere

Replaces wm.max_level with wm.num_levels, since that generally
results in nicer looking code (for-loops can be in standard
form etc.).

Also get rid of the two different wrappers we have for this
(ilk_wm_max_level() and intel_wm_num_levels()). They don't
really do anything for us other than potentially slow things
down if the compiler actually emits the function calls every
time (num_planes*num_wm_levels*higher_level_wm_function_calls
could be a big number). The watermark code already shows up
far too prominently in cpu profiles. Though I must admit that
I didn't look at the generated code this time.

v2: Fix the ilk_wm_merge() off-by-one (Jani)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230209222504.31478-1-ville.syrjala@linux.intel.com

drm/i915: Populate wm.max_level for everyone

Switch ilk+ and skl+ platforms to also setting up
wm.max_level and remove a bunch of if ladders as a result.

There will be a tiny change in the debugfs on CHV machines
that have DVFS disabled in the BIOS. Presviously debugfs
would show the latency for the DVFS level as well, but
that will no longer be the case. Which is arguably better
as that number is absolutely meaningless when DVFS can't
be enabled anyway.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230209003251.32021-1-ville.syrjala@linux.intel.com

drm/i915/mtl: Initialize empty clockgating hooks for MTL

Clock gating hooks to be initialized for MTL are yet to be implemented.
Use a nop till we identify relevant WA's here.

Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230111235531.3353815-3-radhakrishna.sripada@intel.com

drm/i915/dg2: Drop one PCI ID

The bspec was recently updated to remove PCI ID 0x5698; this ID is
actually reserved for future use and should not be treated as DG2-G11.

Bspec: 44477
Fixes: 8618b8489ba6 ("drm/i915: DG2 and ATS-M device ID updates")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208200905.680865-1-matthew.d.roper@intel.com

Revert "drm/i915/hwmon: Enable PL1 power limit"

This reverts commit 0349c41b05968befaffa5fbb7e73d0ee6004f610.

0349c41b0596 ("drm/i915/hwmon: Enable PL1 power limit") is incorrect and
caused a major regression on ATSM. The change enabled the PL1 power limit
but FW sets the default value of the PL1 limit to 0 which implies HW now
works at minimum power and therefore the lowest effective frequency. This
means all workloads now run slower resulting in even GuC FW load operations
timing out, rendering ATSM unusable.

A different solution to the original issue of the PL1 limit being disabled
on ATSM is needed but till that is developed, revert 0349c41b0596.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8062
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208190312.1611335-1-ashutosh.dixit@intel.com

drm/i915/bios: set default backlight controller index

With backlight controller set to -1 in intel_panel_init_alloc() to
distinguish uninitialized values, and controller later being set only if
it's present in VBT, we can end up with -1 for the controller:

    [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation
    frequency 200 Hz, active high, min brightness 0, level 255,
    controller 4294967295

There's no harm if it happens on platforms that ignore controller due to
only one backlight controller being present, like on VLV above, but play
it safe.

Fixes: bf38bba3e7d6 ("drm/i915: Try to use the correct power sequencer intiially on bxt/glk")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207111626.1839645-1-jani.nikula@intel.com

drm/i915/uncore: cast iomem to avoid sparse warning

drmm_add_action_or_reset() is unaware of __iomem and the pointer needs
to be a plain void *. Cast __iomem away and back while the pointer goes
through drmm.

drivers/gpu/drm/i915/intel_uncore.c:2463:17: warning: incorrect type in argument 1 (different address spaces)
drivers/gpu/drm/i915/intel_uncore.c:2463:17:    expected void volatile [noderef] __iomem *addr
drivers/gpu/drm/i915/intel_uncore.c:2463:17:    got void *regs
drivers/gpu/drm/i915/intel_uncore.c:2494:16: warning: incorrect type in argument 3 (different address spaces)
drivers/gpu/drm/i915/intel_uncore.c:2494:16:    expected void *data
drivers/gpu/drm/i915/intel_uncore.c:2494:16:    got void [noderef] __iomem *regs

Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207124026.2105442-2-jani.nikula@intel.com

drm/i915/dmc: drop "ucode" from function names

The ucode part in the init, fini, suspend and resume function names is
just unnecessary. Drop it.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207110619.1821992-1-jani.nikula@intel.com

drm/i915: Pick the backlight controller based on VBT on ICP+

Use the second backlight controller on ICP+ if the VBT asks
us to do so.

On pre-MTP we also check the chicken bit to make sure the
pins have been correctly muxed by the firmware.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8016
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207064337.18697-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Populate encoder->devdata for DSI on icl+

We now have some eDP+DSI dual panel systems floating around
where the DSI panel is the secondary LFP and thus needs to
consult "panel type 2" in VBT in order to locate all the
other panel type dependant stuff correctly.

To that end we need to pass in the devdata to
intel_bios_init_panel_late(), otherwise it'll just assume
we want the primary panel type. So let's try to just populate
the vbt.ports[] stuff and encoder->devdata for icl+ DSI
panels as well.

We can't do this on older platforms as there we risk a DSI
port aliasing with a HDMI/DP port, which is a totally legal
thing as the DSI ports live in their own little parallel
universe.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8016
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207064337.18697-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix VBT DSI DVO port handling

Turns out modern (icl+) VBTs still declare their DSI ports
as MIPI-A and MIPI-C despite the PHYs now being A and B.
Remap appropriately to allow the panels declared as MIPI-C
to work.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8016
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207064337.18697-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix memory leaks in scatterlist

This patch fixes memory leaks on error escapes in i915_scatterlist.c

Fixes: c3bfba9a2225 ("drm/i915: Check for integer truncation on scatterlist creation")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230201232801.123684-1-matthew.s.atwood@intel.com

drm/i915: Add another EHL pci id

described as "32 Execution Unit (EU) Super SKU" in:
Intel Atom x6000E Series, and Intel Pentium and Celeron N and
J Series Processors for IoT Applications
Datasheet, Volume 1
Document Number: 636112-1.6

Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230206043727.46069-1-jsg@jsg.id.au

drm/i915/hwmon: Enable PL1 power limit

Previous documentation suggested that PL1 power limit is always
enabled. However we now find this not to be the case on some
platforms (such as ATSM). Therefore enable PL1 power limit during hwmon
initialization.

Bspec: 51864

v2: Add Bspec reference (Gwan-gyeong)
v3: Add Fixes tag

Fixes: 99f55efb79114 ("drm/i915/hwmon: Power PL1 limit and TDP setting")
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230203155309.1042297-1-ashutosh.dixit@intel.com

drm/i915/dsb: Introduce intel_dsb_finish()

Introduce a function to emits whatever commands we need
at the end of the DSB command buffer. For the moment we
only do the tail cacheline alignment there, but eventually
we might want to eg. emit an interrupt.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-5-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/dsb: Split intel_dsb_wait() from intel_dsb_commit()

Starting the DSB execution vs. waiting for it stop are two
totally different things. Split intel_dsb_wait() from
intel_dsb_commit() so that we can eventually allow the DSB
to execute asynchronously.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-4-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/dsb: Pimp debug/error prints

Print the crtc/DSB id information to make it clear which DSB engine
we're talking about.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230118163040.29808-3-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915/fbdev: Implement fb_dirty for intel custom fb helper

After disconnecting damage worker from update logic it's left to fbdev
emulation implementation to have fb_dirty function. Currently intel
fbdev doesn't have it. This is causing problems to features (PSR, FBC,
DRRS) relying on dirty callback.

Implement simple fb_dirty callback to deliver notifications about updates
in fb console.

v4: Add proper Fixes tag and modify commit message
v3: Check damage clip
v2: Improved commit message and added Fixes tag

Fixes: f231af498c29 ("drm/fb-helper: Disconnect damage worker from update logic")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123074437.475103-1-jouni.hogander@intel.com

drm/i915/dmc: check incoming dmc id validity

Add validity checks for the dmc ids computed from pipe parameters in
intel_dmc_enable_pipe() and intel_dmc_disable_pipe(). It's slightly
difficult for humans and static analyzers alike to ensure the resulting
dmc ids are within bounds. Just check them and reject invalid ones.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6a349c3a2b2def5fc31a48c9844ebd72ee55a22b.1675339447.git.jani.nikula@intel.com

drm/i915/dmc: add is_valid_dmc_id() and use it

Add a name to the dmc id validity check.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/311213ce328575a95d793a219d4dac7d947086cc.1675339447.git.jani.nikula@intel.com

drm/i915/dmc: remove unnecessary dmc_id validity check

The dmc_id comes from for_each_dmc_id() in parse_dmc_fw() ->
parse_dmc_fw_header() -> dmc_mmio_addr_sanity_check(). It's valid by
definition.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b4e1c862687f79861a5fa4bfa6797ecda2136fab.1675339447.git.jani.nikula@intel.com

drm/i915/dmc: add for_each_dmc_id() and use it

The loop is duplicated many times, with slightly different ways. Unify.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8dcaa716093e6fbe75bb69ee7ac715a3f007a523.1675339447.git.jani.nikula@intel.com

drm/i915/dmc: add proper name to dmc id enum and use it

Clarify DMC ID usage by adding enum intel_dmc_id name to the enum, and
use dmc_id as the variable name for it throughout.

Convert a switch-case to if-ladder to avoid warnings about not handling
DMC_FW_MAX enumeration constant in the switch-case.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6912ccb411bb957c68c108b774745dbc7e0cbdc2.1675339447.git.jani.nikula@intel.com

drm/i915: Expose SAGV state via debugfs

Since SAGV is controlled via unidirectional pcode commands
we have no way to query the current state. So instead let's
expose the last programmed state via debugfs. This way we
can at least know whether SAGV should be enabled or not
(which can be important to know when dealing with underruns/etc.).

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230131002127.29305-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Keep sagv status updated on icl+

On icl+ SAGV is controlled by masking of the QGV points.
Reduce the QGV point mask to the same kind of enabled vs.
disable information that we had on previous platforms.
Will be useful in answering the question whether SAGV is
actually enabled or not.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230131002127.29305-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>