linux-2.6-microblaze.git
15 years agoBlackfin: bf526-ezbrd: set SPI flash resources to SST device
Graf Yang [Mon, 15 Jun 2009 08:23:41 +0000 (08:23 +0000)]
Blackfin: bf526-ezbrd: set SPI flash resources to SST device

The BF526-EZBRD has a SST SPI flash on it, not a ST Micro.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: fix accidental reset in some boot modes
Sonic Zhang [Mon, 15 Jun 2009 07:39:19 +0000 (07:39 +0000)]
Blackfin: fix accidental reset in some boot modes

We read the SWRST (Software Reset) register to get at the last reset
state, and then we may configure the DOUBLE_FAULT bit to control behavior
when a double fault occurs.  But if the lower bits of the register is
already set (like UART boot mode on a BF54x), we inadvertently make the
system reset by writing to the SYSTEM_RESET field at the same time.  So
make sure the lower 4 bits are always cleared.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: abstract irq14 lowering in do_irq
Mike Frysinger [Mon, 15 Jun 2009 10:22:08 +0000 (06:22 -0400)]
Blackfin: abstract irq14 lowering in do_irq

Split out the optional IRQ14 lowering code to further simplify the
asm_do_IRQ() function and keep the ifdef nest under control.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: simplify irq stack overflow checking
Mike Frysinger [Mon, 15 Jun 2009 10:18:38 +0000 (06:18 -0400)]
Blackfin: simplify irq stack overflow checking

Take a page from x86 and abstract the stack checking out of the
asm_do_IRQ() function so that the result is easier to digest.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: only build show_interrupts() when procfs is enabled
Mike Frysinger [Mon, 15 Jun 2009 10:13:58 +0000 (06:13 -0400)]
Blackfin: only build show_interrupts() when procfs is enabled

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: redo handling of bad irqs
Mike Frysinger [Mon, 15 Jun 2009 10:10:03 +0000 (06:10 -0400)]
Blackfin: redo handling of bad irqs

With the common IRQ code initializing much more of the irq_desc state, we
can't blindly initialize it ourselves to the local bad_irq state.  If we
do, we end up wrongly clobbering many fields.  So punt most of the bad irq
code as the common layers will handle the default state, and simply call
handle_bad_irq() directly when the IRQ we are processing is invalid.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: update anomaly lists
Mike Frysinger [Sat, 13 Jun 2009 10:37:14 +0000 (06:37 -0400)]
Blackfin: update anomaly lists

Update anomaly headers to match latest released anomaly sheets.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: bf533-ezkit: add resources for FISP devices
Mike Frysinger [Sat, 13 Jun 2009 10:34:49 +0000 (06:34 -0400)]
Blackfin: bf533-ezkit: add resources for FISP devices

The BF533-EZKIT has two Flash In-System Programming devices hooked up to
the async memory bus, so add resources for the primary flashes and the
SRAMs on the devices.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: bf518f-ezbrd: update DSA resources
Mike Frysinger [Thu, 11 Jun 2009 13:22:02 +0000 (09:22 -0400)]
Blackfin: bf518f-ezbrd: update DSA resources

The common DSA code changed structure layout, so update the BF518F-EZBRD
resources accordingly.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: unify memory region checks between kgdb and traps
Mike Frysinger [Sun, 7 Jun 2009 20:31:52 +0000 (16:31 -0400)]
Blackfin: unify memory region checks between kgdb and traps

The kgdb (in multiple places) and traps code developed pretty much
identical checks for how to access different regions of the Blackfin
memory map, but each wasn't 100%, so unify them to avoid duplication,
bitrot, and bugs with edge cases.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoMerge git://git.infradead.org/mtd-2.6
Linus Torvalds [Mon, 22 Jun 2009 23:56:22 +0000 (16:56 -0700)]
Merge git://git.infradead.org/mtd-2.6

* git://git.infradead.org/mtd-2.6: (63 commits)
  mtd: OneNAND: Allow setting of boundary information when built as module
  jffs2: leaking jffs2_summary in function jffs2_scan_medium
  mtd: nand: Fix memory leak on txx9ndfmc probe failure.
  mtd: orion_nand: use burst reads with double word accesses
  mtd/nand: s3c6400 support for s3c2410 driver
  [MTD] [NAND] S3C2410: Use DIV_ROUND_UP
  [MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
  [MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
  [MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
  mtd: physmap_of: Add multiple regions and concatenation support
  mtd: nand: max_retries off by one in mxc_nand
  mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
  mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
  mtd: Flex-OneNAND support
  mtd: nand: add OMAP2/OMAP3 NAND driver
  mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
  mtd: uclinux: mark local stuff static
  mtd: uclinux: do not allow to be built as a module
  mtd: uclinux: allow systems to override map addr/size
  mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
  ...

15 years agoMerge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
Linus Torvalds [Mon, 22 Jun 2009 21:56:13 +0000 (14:56 -0700)]
Merge branch 'devel' of /home/rmk/linux-2.6-arm

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (49 commits)
  [ARM] idle: clean up pm_idle calling, obey hlt_counter
  [ARM] S3C: Fix gpio-config off-by-one bug
  [ARM] S3C64XX: add to_irq() support for EINT() GPIO
  [ARM] S3C64XX: clock.c: fix typo in usb-host clock ctrlbit
  [ARM] S3C64XX: fix HCLK gate defines
  [ARM] Update mach-types
  [ARM] wire up rt_tgsigqueueinfo and perf_counter_open
  OMAP2 clock/powerdomain: off by 1 error in loop timeout comparisons
  OMAP3 SDRC: set FIXEDDELAY when disabling SDRC DLL
  OMAP3: Add support for DPLL3 divisor values higher than 2
  OMAP3 SRAM: convert SRAM code to use macros rather than magic numbers
  OMAP3 SRAM: add more comments on the SRAM code
  OMAP3 clock/SDRC: program SDRC_MR register during SDRC clock change
  OMAP3 clock: add a short delay when lowering CORE clk rate
  OMAP3 clock: initialize SDRC timings at kernel start
  OMAP3 clock: remove wait for DPLL3 M2 clock to stabilize
  [ARM] Add old Feroceon support to compressed/head.S
  [ARM] 5559/1: Limit the stack unwinding caused by a kthread exit
  [ARM] 5558/1: Add extra checks to ARM unwinder to avoid tracing corrupt stacks
  [ARM] 5557/1: Discard some ARM.ex*.*exit.text sections when !HOTPLUG or !HOTPLUG_CPU
  ...

15 years ago[ARM] idle: clean up pm_idle calling, obey hlt_counter
Russell King [Mon, 22 Jun 2009 21:34:55 +0000 (22:34 +0100)]
[ARM] idle: clean up pm_idle calling, obey hlt_counter

pm_idle is used by infrastructure (eg, cpuidle) which expects architectures
to call it in a certain way.  Arrange for ARM to follow x86's lead on this
and call pm_idle() with interrupts already disabled.  However, we expect
pm_idle() to enable interrupts before it returns.

Also, OMAP wants to be able to disable hlt-ing, so allow hlt_counter to
prevent all calls to pm_idle.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
15 years agoMN10300: Fix the vmlinux ldscript
David Howells [Mon, 22 Jun 2009 14:32:36 +0000 (15:32 +0100)]
MN10300: Fix the vmlinux ldscript

Fix the MN10300 vmlinux ldscript.  It needs to use various macros from
asm-generic/vmlinux.lds.h to correctly include all that it needs to.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoLDSCRIPT: Name INIT_RAM_FS consistently
David Howells [Mon, 22 Jun 2009 14:32:31 +0000 (15:32 +0100)]
LDSCRIPT: Name INIT_RAM_FS consistently

In asm-generic/vmlinux.lds.h, name INIT_RAM_FS consistently, no matter the
setting of CONFIG_BLK_DEV_INITRD.  This corrects:

commit ef53dae8658cf0e93d380983824a661067948d87
Author: Sam Ravnborg <sam@ravnborg.org>
Date:   Sun Jun 7 20:46:37 2009 +0200
Subject: Improve vmlinux.lds.h support for arch specific linker scripts

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoMerge branch 'for-2.6.31' of git://fieldses.org/git/linux-nfsd
Linus Torvalds [Mon, 22 Jun 2009 19:55:50 +0000 (12:55 -0700)]
Merge branch 'for-2.6.31' of git://fieldses.org/git/linux-nfsd

* 'for-2.6.31' of git://fieldses.org/git/linux-nfsd: (60 commits)
  SUNRPC: Fix the TCP server's send buffer accounting
  nfsd41: Backchannel: minorversion support for the back channel
  nfsd41: Backchannel: cleanup nfs4.0 callback encode routines
  nfsd41: Remove ip address collision detection case
  nfsd: optimise the starting of zero threads when none are running.
  nfsd: don't take nfsd_mutex twice when setting number of threads.
  nfsd41: sanity check client drc maxreqs
  nfsd41: move channel attributes from nfsd4_session to a nfsd4_channel_attr struct
  NFS: kill off complicated macro 'PROC'
  sunrpc: potential memory leak in function rdma_read_xdr
  nfsd: minor nfsd_vfs_write cleanup
  nfsd: Pull write-gathering code out of nfsd_vfs_write
  nfsd: track last inode only in use_wgather case
  sunrpc: align cache_clean work's timer
  nfsd: Use write gathering only with NFSv2
  NFSv4: kill off complicated macro 'PROC'
  NFSv4: do exact check about attribute specified
  knfsd: remove unreported filehandle stats counters
  knfsd: fix reply cache memory corruption
  knfsd: reply cache cleanups
  ...

15 years agoMerge branch 'for-2.6.31' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
Linus Torvalds [Mon, 22 Jun 2009 19:53:06 +0000 (12:53 -0700)]
Merge branch 'for-2.6.31' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6

* 'for-2.6.31' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (128 commits)
  nfs41: sunrpc: xprt_alloc_bc_request() should not use spin_lock_bh()
  nfs41: Move initialization of nfs4_opendata seq_res to nfs4_init_opendata_res
  nfs: remove unnecessary NFS_INO_INVALID_ACL checks
  NFS: More "sloppy" parsing problems
  NFS: Invalid mount option values should always fail, even with "sloppy"
  NFS: Remove unused XDR decoder functions
  NFS: Update MNT and MNT3 reply decoding functions
  NFS: add XDR decoder for mountd version 3 auth-flavor lists
  NFS: add new file handle decoders to in-kernel mountd client
  NFS: Add separate mountd status code decoders for each mountd version
  NFS: remove unused function in fs/nfs/mount_clnt.c
  NFS: Use xdr_stream-based XDR encoder for MNT's dirpath argument
  NFS: Clean up MNT program definitions
  lockd: Don't bother with RPC ping for NSM upcalls
  lockd: Update NSM state from SM_MON replies
  NFS: Fix false error return from nfs_callback_up() if ipv6.ko is not available
  NFS: Return error code from nfs_callback_up() to user space
  NFS: Do not display the setting of the "intr" mount option
  NFS: add support for splice writes
  nfs41: Backchannel: CB_SEQUENCE validation
  ...

15 years agoMerge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
Linus Torvalds [Mon, 22 Jun 2009 19:51:28 +0000 (12:51 -0700)]
Merge branch 'for-linus' of git://git390.marist.edu/linux-2.6

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (22 commits)
  [S390] Update default configuration.
  [S390] kprobes: defer setting of ctlblk state
  [S390] Enable tick based perf_counter on s390.
  [S390] dasd: fix refcounting in dasd_change_state
  [S390] lockless idle time accounting
  [S390] driver_data access
  [S390] pm: fix build error for !SMP
  [S390] dasd_pm: fix stop flag handling
  [S390] ap/zcrypt: Suspend/Resume ap bus and zcrypt
  [S390] qdio: Sanitize do_QDIO sanity checks
  [S390] qdio: leave inbound SBALs primed
  [S390] qdio: merge AI tasklet into interrupt handler
  [S390] qdio: extract all primed SBALs at once
  [S390] qdio: fix check for running under z/VM
  [S390] qdio: move adapter interrupt tasklet code
  [S390] Use del_timer instead of del_timer_sync
  [S390] s390: remove DEBUG_MALLOC
  [S390] vt220 console: convert from bootmem to slab
  [S390] sclp console: convert from bootmem to slab
  [S390] 3270 console: convert from bootmem to slab
  ...

15 years agoMerge branch 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux
Linus Torvalds [Mon, 22 Jun 2009 19:44:14 +0000 (12:44 -0700)]
Merge branch 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux

* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
  i2c: Fix stuck transaction on cpm-i2c driver
  i2c-omap: Fix build breaking typo cpu_is_omap_2430

15 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6
Linus Torvalds [Mon, 22 Jun 2009 19:38:31 +0000 (12:38 -0700)]
Merge git://git./linux/kernel/git/czankel/xtensa-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6:
  xtensa: enable m41t80 driver in s6105_defconfig
  xtensa: add m41t62 rtc to s6105 platform
  xtensa: enable s6gmac in s6105_defconfig
  xtensa: s6105 specific configuration for s6gmac
  s6gmac: xtensa s6000 on-chip ethernet driver
  xtensa: support s6000 gpio irqs and alternate function selection
  xtensa: s6000 dma engine support
  xtensa: allow variant to initialize own irq chips
  xtensa: cache inquiry and unaligned cache handling functions

15 years agoMerge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes...
Linus Torvalds [Mon, 22 Jun 2009 18:59:51 +0000 (11:59 -0700)]
Merge branch 'linux-next' of git://git./linux/kernel/git/jbarnes/pci-2.6

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
  PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
  PCI: Fix the NIU MSI-X problem in a better way
  PCI ASPM: remove get_root_port_link
  PCI ASPM: cleanup pcie_aspm_sanity_check
  PCI ASPM: remove has_switch field
  PCI ASPM: cleanup calc_Lx_latency
  PCI ASPM: cleanup pcie_aspm_get_cap_device
  PCI ASPM: cleanup clkpm checks
  PCI ASPM: cleanup __pcie_aspm_check_state_one
  PCI ASPM: cleanup initialization
  PCI ASPM: cleanup change input argument of aspm functions
  PCI ASPM: cleanup misc in struct pcie_link_state
  PCI ASPM: cleanup clkpm state in struct pcie_link_state
  PCI ASPM: cleanup latency field in struct pcie_link_state
  PCI ASPM: cleanup aspm state field in struct pcie_link_state
  PCI ASPM: fix typo in struct pcie_link_state
  PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
  PCI: remove redundant __msi_set_enable()
  PCI PM: consistently use type bool for wake enable variable
  x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
  ...

15 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
Linus Torvalds [Mon, 22 Jun 2009 18:57:09 +0000 (11:57 -0700)]
Merge git://git./linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (43 commits)
  via-velocity: Fix velocity driver unmapping incorrect size.
  mlx4_en: Remove redundant refill code on RX
  mlx4_en: Removed redundant check on lso header size
  mlx4_en: Cancel port_up check in transmit function
  mlx4_en: using stop/start_all_queues
  mlx4_en: Removed redundant skb->len check
  mlx4_en: Counting all the dropped packets on the TX side
  usbnet cdc_subset: fix issues talking to PXA gadgets
  Net: qla3xxx, remove sleeping in atomic
  ipv4: fix NULL pointer + success return in route lookup path
  isdn: clean up documentation index
  cfg80211: validate station settings
  cfg80211: allow setting station parameters in mesh
  cfg80211: allow adding/deleting stations on mesh
  ath5k: fix beacon_int handling
  MAINTAINERS: Fix Atheros pattern paths
  ath9k: restore PS mode, before we put the chip into FULL SLEEP state.
  ath9k: wait for beacon frame along with CAB
  acer-wmi: fix rfkill conversion
  ath5k: avoid PCI FATAL interrupts by restoring RETRY_TIMEOUT disabling
  ...

15 years agoMaking fs/minix/minix.h double including safe
Hitoshi Mitake [Mon, 22 Jun 2009 02:11:20 +0000 (11:11 +0900)]
Making fs/minix/minix.h double including safe

I happened to find that fs/minix/minix.h doesn't guard double include.

Yes, I know this never cause something destructive because this is
self-evidence that no source file includes minix.h twice, but I think
fixing this is better than disregarding it.

Signed-off-by: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomsm: fixups to match current code
Alan Cox [Mon, 22 Jun 2009 17:43:18 +0000 (18:43 +0100)]
msm: fixups to match current code

The tty layer is now a bit more fussy about reporting the right baud rate
back. Make the msm driver match the current state of affairs.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomsm_serial: serial driver for MSM7K onboard serial peripheral.
Robert Love [Mon, 22 Jun 2009 17:43:11 +0000 (18:43 +0100)]
msm_serial: serial driver for MSM7K onboard serial peripheral.

Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agotimbuart: Fix for tx_empty
Richard Röjfors [Mon, 22 Jun 2009 17:43:03 +0000 (18:43 +0100)]
timbuart: Fix for tx_empty

Hardware updated to support TX FIFO empty.

Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agotty: n_hdlc add buffer flushing
Paul Fulghum [Mon, 22 Jun 2009 17:42:56 +0000 (18:42 +0100)]
tty: n_hdlc add buffer flushing

Add flush_buffer tty callback to flush rx buffers.
Add TCFLSH ioctl processing to flush tx buffers.
Increase default tx buffers from 1 to 3.
Remove unneeded flush_buffer call in open callback.
Remove vendor specific CVS version string.

Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoserial: samsung.c: mark s3c24xx_serial_remove as __devexit
Peter Korsgaard [Mon, 22 Jun 2009 17:42:49 +0000 (18:42 +0100)]
serial: samsung.c: mark s3c24xx_serial_remove as __devexit

Mark the remove function as __devexit so it gets eliminated in
CONFIG_HOTPLUG=n builds.  Saves ~100 bytes.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoserial@ add OMAP wakeup-enable register
Kevin Hilman [Mon, 22 Jun 2009 17:42:42 +0000 (18:42 +0100)]
serial@ add OMAP wakeup-enable register

Add the wakeup enable register to the list of OMAP-specific UART
registers.  This is to support forthcoming OMAP PM enhancements which
use the wakeup feature of the OMAP's 8250-based UART.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agotty: fix some bogns in the serqt_usb2 driver
Alan Cox [Mon, 22 Jun 2009 17:42:36 +0000 (18:42 +0100)]
tty: fix some bogns in the serqt_usb2 driver

Remove the replicated urban legends from the comments and fix a couple of
other silly calls

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoppp: Fix throttling bugs
Alan Cox [Mon, 22 Jun 2009 17:42:29 +0000 (18:42 +0100)]
ppp: Fix throttling bugs

The ppp layer goes around calling the unthrottle method from non sleeping
paths. This isn't safe because the unthrottle methods in the tty layer need
to be able to sleep (consider a USB dongle).

Until now this didn't show up because the ppp layer never actually throttled
a port so the unthrottle was always a no-op. Currently it's a mutex taking
path so warnings are spewed if the unthrottle occurs via certain paths.

Fix this by removing the unneccessary unthrottle calls.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agovt_ioctl: fix lock imbalance
Jiri Slaby [Mon, 22 Jun 2009 17:42:18 +0000 (18:42 +0100)]
vt_ioctl: fix lock imbalance

Don't return from switch/case directly in vt_ioctl. Set ret and break
instead so that we unlock BKL.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agopcmcia/cm4000: fix lock imbalance
Jiri Slaby [Mon, 22 Jun 2009 17:42:10 +0000 (18:42 +0100)]
pcmcia/cm4000: fix lock imbalance

Don't return from switch/case, break instead, so that we unlock BKL.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agon_r3964: fix lock imbalance
Jiri Slaby [Mon, 22 Jun 2009 17:42:03 +0000 (18:42 +0100)]
n_r3964: fix lock imbalance

There is omitted BKunL in r3964_read.

Centralize the paths to one point with one unlock.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoserial: fix off by one errors
Roel Kluin [Mon, 22 Jun 2009 17:41:56 +0000 (18:41 +0100)]
serial: fix off by one errors

In zs_console_putchar() occurs:

if (zs_transmit_drain(zport, irq))
write_zsdata(zport, ch);

However if in zs_transmit_drain() no empty Tx Buffer occurs, limit reaches
-1 => true, and the write still occurs.

This patch changes postfix to prefix decrements in this and similar
functions to prevent similar mistakes in the future.  This decreases the
iterations with one but the chosen loop count was arbitrary anyway.

In sunhv limit reaches -1, not 0, so the test is off by one.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoserial: bfin_5xx: fix building as module when early printk is enabled
Mike Frysinger [Mon, 22 Jun 2009 17:41:47 +0000 (18:41 +0100)]
serial: bfin_5xx: fix building as module when early printk is enabled

Since early printk only makes sense/works when the serial driver is built
into the kernel, disable the option for this driver when it is going to be
built as a module.  Otherwise we get build failures due to the ifdef
handling.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoserial: bfin_5xx: add missing spin_lock init
Mike Frysinger [Mon, 22 Jun 2009 17:37:24 +0000 (18:37 +0100)]
serial: bfin_5xx: add missing spin_lock init

The Blackfin serial driver never initialized the spin_lock that is part of
the serial core structure, but we never noticed because spin_lock's are
rarely enabled on UP systems.  Yeah lockdep and friends.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agobfin_jtag_comm: clean up printk usage
Mike Frysinger [Mon, 22 Jun 2009 17:31:10 +0000 (18:31 +0100)]
bfin_jtag_comm: clean up printk usage

The original patch garned some feedback and a v2 was posted, but that
version seems to have been missed when merging the driver.

At any rate, this cleans up the printk usage as suggested by Jiri Slaby.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoparport_pc: set properly the dma_mask for parport_pc device
FUJITA Tomonori [Mon, 22 Jun 2009 15:54:27 +0000 (16:54 +0100)]
parport_pc: set properly the dma_mask for parport_pc device

parport_pc_probe_port() creates the own 'parport_pc' device if the
device argument is NULL. Then parport_pc_probe_port() doesn't
initialize the dma_mask and coherent_dma_mask of the device and calls
dma_alloc_coherent with it. dma_alloc_coherent fails because
dma_alloc_coherent() doesn't accept the uninitialized dma_mask:

http://lkml.org/lkml/2009/6/16/150

Long ago, X86_32 and X86_64 had the own dma_alloc_coherent
implementations; X86_32 accepted a device having dma_mask that is not
initialized however X86_64 didn't. When we merged them, we chose to
prohibit a device having dma_mask that is not initialized. I think
that it's good to require drivers to set up dma_mask (and
coherent_dma_mask) properly if the drivers want DMA.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reported-by: Malcom Blaney <malcolm.blaney@maptek.com.au>
Tested-by: Malcom Blaney <malcolm.blaney@maptek.com.au>
Cc: stable@kernel.org
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoparport_pc: after superio probing restore original register values
Jens Rottmann [Mon, 22 Jun 2009 15:51:49 +0000 (16:51 +0100)]
parport_pc: after superio probing restore original register values

CONFIG_PARPORT_PC_SUPERIO probes for various superio chips by writing
byte sequences to a set of different potential I/O ranges.  But the
probed ranges are not exclusive to parallel ports.  Some of our boards
just happen to have a watchdog in one of them.  Took us almost a week
to figure out why some distros reboot without warning after running
flawlessly for 3 hours.  For exactly 170 = 0xAA minutes, that is ...

Fixed by restoring original values after probing.  Also fixed too small
request_region() in detect_and_report_it87().

Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: <stable@kernel.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoRevert "char: moxa, prevent opening unavailable ports"
Linus Torvalds [Mon, 22 Jun 2009 18:24:43 +0000 (11:24 -0700)]
Revert "char: moxa, prevent opening unavailable ports"

This reverts commit a90b037583d5f1ae3e54e9c687c79df82d1d34a4, which
already got fixed as commit f0e8527726b9e56649b9eafde3bc0fbc4dd2dd47:
the same patch (trivial differences) got applied twice.

Requested-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoMerge branch 'next-s3c' of git://aeryn.fluff.org.uk/bjdooks/linux into devel
Russell King [Mon, 22 Jun 2009 13:31:57 +0000 (14:31 +0100)]
Merge branch 'next-s3c' of git://aeryn.fluff.org.uk/bjdooks/linux into devel

15 years ago[ARM] S3C: Fix gpio-config off-by-one bug
Marek Szyprowski [Thu, 18 Jun 2009 11:30:16 +0000 (13:30 +0200)]
[ARM] S3C: Fix gpio-config off-by-one bug

Fix gpio-config off-by-one bug. Without this patch, touching GPA0 pin on
S3C64XX platform causes kernel oops.

Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
15 years ago[ARM] S3C64XX: add to_irq() support for EINT() GPIO
Marek Szyprowski [Thu, 18 Jun 2009 11:30:27 +0000 (13:30 +0200)]
[ARM] S3C64XX: add to_irq() support for EINT() GPIO
N group

Add to_irq() function to onvert gpio to irq for external interrupt
group (GPN).

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
15 years ago[ARM] S3C64XX: clock.c: fix typo in usb-host clock ctrlbit
Peter Korsgaard [Thu, 18 Jun 2009 21:54:44 +0000 (23:54 +0200)]
[ARM] S3C64XX: clock.c: fix typo in usb-host clock ctrlbit

The usb-host clock was using the wrong define (the SCLK enable for the
usb-host-bus) to change the HCLK register instead of the HCLK_UHOST bit.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
15 years ago[ARM] S3C64XX: fix HCLK gate defines
Peter Korsgaard [Thu, 18 Jun 2009 21:54:43 +0000 (23:54 +0200)]
[ARM] S3C64XX: fix HCLK gate defines

A few typos seems to have sneaked into the HCLK gate defines, causing the
usb host clock to not get enabled. Fix them according to the reference
manual and throw in the 3d accel bit for good measure.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
15 years ago[S390] Update default configuration.
Martin Schwidefsky [Mon, 22 Jun 2009 10:08:24 +0000 (12:08 +0200)]
[S390] Update default configuration.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] kprobes: defer setting of ctlblk state
Heiko Carstens [Mon, 22 Jun 2009 10:08:23 +0000 (12:08 +0200)]
[S390] kprobes: defer setting of ctlblk state

get_krobe_ctlblk returns a per cpu kprobe control block which holds
the state of the current cpu wrt to kprobe.
When inserting/removing a kprobe the state of the cpu which replaces
the code is changed to KPROBE_SWAP_INST. This however is done when
preemption is still enabled. So the state of the current cpu doesn't
necessarily reflect the real state.
To fix this move the code that changes the state to non-preemptible
context.

Reported-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] Enable tick based perf_counter on s390.
Martin Schwidefsky [Mon, 22 Jun 2009 10:08:22 +0000 (12:08 +0200)]
[S390] Enable tick based perf_counter on s390.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] dasd: fix refcounting in dasd_change_state
Sebastian Ott [Mon, 22 Jun 2009 10:08:21 +0000 (12:08 +0200)]
[S390] dasd: fix refcounting in dasd_change_state

To set a dasd online dasd_change_state is called twice. The first
cycle will schedule initial analysis of the device, set the rc to
-EAGAIN and will not touch the device state any more.
The initial analysis will in turn call dasd_change_state to increase
the state to the final DASD_STATE_ONLINE.

If the dasd_change_state on the second thread outruns the other one
both finish with the state set to DASD_STATE_ONLINE and the device
refcount will be decreased by 2.

Fix this by leaving dasd_change_state on rc == -EAGAIN so that the
refcount will always be decreased by 1.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] lockless idle time accounting
Martin Schwidefsky [Mon, 22 Jun 2009 10:08:20 +0000 (12:08 +0200)]
[S390] lockless idle time accounting

Replace the spinlock used in the idle time accounting with a sequence
counter mechanism analog to seqlock.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] driver_data access
Martin Schwidefsky [Mon, 22 Jun 2009 10:08:19 +0000 (12:08 +0200)]
[S390] driver_data access

Replace the remaining direct accesses to the driver_data pointer
with calls to the dev_get_drvdata() and dev_set_drvdata() functions.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] pm: fix build error for !SMP
Heiko Carstens [Mon, 22 Jun 2009 10:08:18 +0000 (12:08 +0200)]
[S390] pm: fix build error for !SMP

Fix build error for !SMP:

arch/s390/power/built-in.o: In function `swsusp_arch_resume':
(.text+0x1b4): undefined reference to `smp_get_phys_cpu_id'
arch/s390/power/built-in.o: In function `swsusp_arch_resume':
(.text+0x288): undefined reference to `smp_switch_boot_cpu_in_resume'
make: *** [.tmp_vmlinux1] Error 1

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] dasd_pm: fix stop flag handling
Stefan Haberland [Mon, 22 Jun 2009 10:08:17 +0000 (12:08 +0200)]
[S390] dasd_pm: fix stop flag handling

The stop flags are handled in the generic restore function so the
stop flag is removed also for FBA and DIAG devices.

Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] ap/zcrypt: Suspend/Resume ap bus and zcrypt
Felix Beck [Mon, 22 Jun 2009 10:08:16 +0000 (12:08 +0200)]
[S390] ap/zcrypt: Suspend/Resume ap bus and zcrypt

Add Suspend/Resume support to ap bus and zcrypt. All enhancements are
done in the ap bus. No changes in the crypto card specific part are
necessary.

Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] qdio: Sanitize do_QDIO sanity checks
Jan Glauber [Mon, 22 Jun 2009 10:08:15 +0000 (12:08 +0200)]
[S390] qdio: Sanitize do_QDIO sanity checks

Remove unneeded sanity checks from do_QDIO since this is the hot path.
Change the type of bufnr and count to unsigned int so the check for the
maximum value works.

Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] qdio: leave inbound SBALs primed
Jan Glauber [Mon, 22 Jun 2009 10:08:14 +0000 (12:08 +0200)]
[S390] qdio: leave inbound SBALs primed

It is not required to change the state of primed SBALs. Leaving them
primed saves a SQBS instruction under z/VM.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] qdio: merge AI tasklet into interrupt handler
Jan Glauber [Mon, 22 Jun 2009 10:08:13 +0000 (12:08 +0200)]
[S390] qdio: merge AI tasklet into interrupt handler

Since the adapter interrupt tasklet only schedules the queue tasklets
and contains no code that requires serialization in can be merged
with the adapter interrupt handler. That possibly safes some CPU
cycles.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] qdio: extract all primed SBALs at once
Jan Glauber [Mon, 22 Jun 2009 10:08:12 +0000 (12:08 +0200)]
[S390] qdio: extract all primed SBALs at once

For devices without QIOASSIST primed SBALS were extracted in a loop.
Remove the loop since get_buf_states can already return more than
one primed SBAL.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] qdio: fix check for running under z/VM
Jan Glauber [Mon, 22 Jun 2009 10:08:11 +0000 (12:08 +0200)]
[S390] qdio: fix check for running under z/VM

The check whether qdio runs under z/VM was incorrect since SIGA-Sync is not
set if the device runs with QIOASSIST. Use MACHINE_IS_VM instead to prevent
polling under z/VM.

Merge qdio_inbound_q_done and tiqdio_is_inbound_q_done.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] qdio: move adapter interrupt tasklet code
Jan Glauber [Mon, 22 Jun 2009 10:08:10 +0000 (12:08 +0200)]
[S390] qdio: move adapter interrupt tasklet code

Move the adapter interrupt tasklet function to the qdio main code
since all the functions used by the tasklet are located there.

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] Use del_timer instead of del_timer_sync
Michael Holzheu [Mon, 22 Jun 2009 10:08:09 +0000 (12:08 +0200)]
[S390] Use del_timer instead of del_timer_sync

When syncing the sclp console queue, we call del_timer_sync() while holding
the "sclp_con_lock" spinlock. This lock is also taken in the timer function
"sclp_console_timeout". Therefore the sync version of del_timer() cannot be
used here. Because the synchronous deletion of the timer is only needed
in the suspend callback and in that case only one CPU is remaining and
therefore it is not possible that the timer function is running in parallel,
we can safely use del_timer() instead of del_timer_sync().

Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] s390: remove DEBUG_MALLOC
Pekka Enberg [Mon, 22 Jun 2009 10:08:08 +0000 (12:08 +0200)]
[S390] s390: remove DEBUG_MALLOC

The kernel now has kmemleak and kmemtrace so there's no reason to keep
this ugly s390 hack around. I am not sure how it's supposed to work on
SMP anyway as it uses a global variable to temporarily store the return
value of all kmalloc() calls:

  void *b;

  #define kmalloc(x...) (PRINT_INFO(" kmalloc %p\n",b=kmalloc(x)),b)

Cc: <linux-s390@vger.kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] vt220 console: convert from bootmem to slab
Heiko Carstens [Mon, 22 Jun 2009 10:08:07 +0000 (12:08 +0200)]
[S390] vt220 console: convert from bootmem to slab

The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] sclp console: convert from bootmem to slab
Heiko Carstens [Mon, 22 Jun 2009 10:08:06 +0000 (12:08 +0200)]
[S390] sclp console: convert from bootmem to slab

The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] 3270 console: convert from bootmem to slab
Heiko Carstens [Mon, 22 Jun 2009 10:08:05 +0000 (12:08 +0200)]
[S390] 3270 console: convert from bootmem to slab

The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] 3215 console: convert from bootmem to slab
Heiko Carstens [Mon, 22 Jun 2009 10:08:04 +0000 (12:08 +0200)]
[S390] 3215 console: convert from bootmem to slab

The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years ago[S390] time: convert from bootmem to slab
Heiko Carstens [Mon, 22 Jun 2009 10:08:03 +0000 (12:08 +0200)]
[S390] time: convert from bootmem to slab

The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
15 years agoxtensa: enable m41t80 driver in s6105_defconfig
Daniel Glockner [Wed, 10 Jun 2009 19:58:51 +0000 (12:58 -0700)]
xtensa: enable m41t80 driver in s6105_defconfig

Signed-off-by: Daniel Glockner <dg@emlix.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
15 years agoxtensa: add m41t62 rtc to s6105 platform
Daniel Glockner [Wed, 10 Jun 2009 19:58:50 +0000 (12:58 -0700)]
xtensa: add m41t62 rtc to s6105 platform

Signed-off-by: Daniel Glockner <dg@emlix.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
15 years agoxtensa: enable s6gmac in s6105_defconfig
Daniel Glockner [Wed, 10 Jun 2009 19:58:49 +0000 (12:58 -0700)]
xtensa: enable s6gmac in s6105_defconfig

Signed-off-by: Daniel Glockner <dg@emlix.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Weiner <jw@emlix.com>
Cc: Oskar Schirmer <os@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
15 years agoxtensa: s6105 specific configuration for s6gmac
Oskar Schirmer [Wed, 10 Jun 2009 19:58:48 +0000 (12:58 -0700)]
xtensa: s6105 specific configuration for s6gmac

Platform-specific configuration for the s6gmac driver, including the
PHY interrupt line.

Signed-off-by: Daniel Glockner <dg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Weiner <jw@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
15 years agos6gmac: xtensa s6000 on-chip ethernet driver
Oskar Schirmer [Wed, 10 Jun 2009 19:58:48 +0000 (12:58 -0700)]
s6gmac: xtensa s6000 on-chip ethernet driver

The s6000 on-chip MAC supports 10/100/1000Mbit and is connected to an
external PHY via MII or RGMII interface.

[jw@emlix.com: don't use device->bus_id directly]
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glockner <dg@emlix.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
15 years agoxtensa: support s6000 gpio irqs and alternate function selection
Daniel Glöckner [Tue, 5 May 2009 15:03:22 +0000 (15:03 +0000)]
xtensa: support s6000 gpio irqs and alternate function selection

Implement an irq chip to handle interrupts via gpio.  The GPIO chip
initialization function now takes a bitmask denoting pins that should
be configured for their alternate function.

changes compared to v1:
- fixed bug on edge interrupt configuration
- accommodated to function name change
- moved definition of VARIANT_NR_IRQS to this patch
- renamed __XTENSA_S6000_IRQ_H to _XTENSA_S6000_IRQ_H as requested

Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
15 years agoxtensa: s6000 dma engine support
Oskar Schirmer [Wed, 10 Jun 2009 19:58:45 +0000 (12:58 -0700)]
xtensa: s6000 dma engine support

There are four slightly different dma engines on the s6000 family.
One for memory-memory transfers, the other three for memory-device.

This patch implements a platform-specific kernel-API to control these
engines.  It is needed for the network, video, audio peripherals on
s6000.

Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glockner <dg@emlix.com>
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glockner <dg@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
15 years agoxtensa: allow variant to initialize own irq chips
Daniel Glöckner [Tue, 5 May 2009 15:03:21 +0000 (15:03 +0000)]
xtensa: allow variant to initialize own irq chips

There was already a PLATFORM_NR_IRQS define, which is now accompanied
by a VARIANT_NR_IRQS. To be able to initialize these interrupts,
init_IRQ now calls a variant specific hook.

Changes compared to v1:
- adapted to new CONFIG_VARIANT_IRQ_EXT
- removed definition and call of platform_init_IRQ as there already
  is a platform_init_irq defined in asm/platform.h with a weak default
  in kernel/platform.c
- renamed variant_init_IRQ to variant_init_irq

Note that I could not find the call site of platform_init_irq although
it is stated in platform.h that it is called from init_IRQ.

Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
15 years agoxtensa: cache inquiry and unaligned cache handling functions
Oskar Schirmer [Wed, 10 Jun 2009 19:58:45 +0000 (12:58 -0700)]
xtensa: cache inquiry and unaligned cache handling functions

The existing xtensa cache handling functions work on page-aligned
memory regions.

These functions are needed for the s6000 dma engine which can work on
a byte-granularity.

Signed-off-by: Oskar Schirmer <os@emlix.com>
Cc: Johannes Weiner <jw@emlix.com>
Cc: Daniel Glockner <dg@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
15 years agovia-velocity: Fix velocity driver unmapping incorrect size.
Dave Jones [Mon, 22 Jun 2009 05:42:30 +0000 (22:42 -0700)]
via-velocity: Fix velocity driver unmapping incorrect size.

When a packet is greater than ETH_ZLEN, we end up assigning the
boolean result of a comparison to the size we unmap.

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agomlx4_en: Remove redundant refill code on RX
Yevgeny Petrilin [Sat, 20 Jun 2009 22:16:10 +0000 (22:16 +0000)]
mlx4_en: Remove redundant refill code on RX

Our RX rings are always full, there is no need to check whether
we need to fill them or not. If we fail to allocate a new socket
buffer, the incoming packet is dropped an the ring remains full.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agomlx4_en: Removed redundant check on lso header size
Yevgeny Petrilin [Sat, 20 Jun 2009 22:16:02 +0000 (22:16 +0000)]
mlx4_en: Removed redundant check on lso header size

This check that verifies that the LSO header along with control
segment and first data segment do not cross 128 bytes is no longer
required.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agomlx4_en: Cancel port_up check in transmit function
Yevgeny Petrilin [Sat, 20 Jun 2009 22:15:52 +0000 (22:15 +0000)]
mlx4_en: Cancel port_up check in transmit function

When closing the port, we stop all transmit queues under the transmit
lock. It ensures that we will not attempt to transmit new packets after
the physical port was closed.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agomlx4_en: using stop/start_all_queues
Yevgeny Petrilin [Sat, 20 Jun 2009 22:15:46 +0000 (22:15 +0000)]
mlx4_en: using stop/start_all_queues

After we moved to be a multi queue device, need to stop/start
all of our transmit queues.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agomlx4_en: Removed redundant skb->len check
Yevgeny Petrilin [Sat, 20 Jun 2009 22:15:39 +0000 (22:15 +0000)]
mlx4_en: Removed redundant skb->len check

We don't need this check in the transmit function

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agomlx4_en: Counting all the dropped packets on the TX side
Yevgeny Petrilin [Sat, 20 Jun 2009 22:15:31 +0000 (22:15 +0000)]
mlx4_en: Counting all the dropped packets on the TX side

Reporting the counter's value through 'ethtool -S'

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agoi2c: Fix stuck transaction on cpm-i2c driver
Michael Trimarchi [Fri, 19 Jun 2009 12:50:02 +0000 (14:50 +0200)]
i2c: Fix stuck transaction on cpm-i2c driver

When a process tries to read/write a disconnected i2c device, it receives a signal (e.g. ctrl-c) and the kernel gets stuck.

BUG: soft lockup - CPU#0 stuck for 61s! [I2CEEpromTest:392]
NIP: c01628f8 LR: c01628f0 CTR: c00177cc
REGS: c39abd70 TRAP: 0901   Not tainted  (2.6.25.7-alcore)
MSR: 00009032 <EE,ME,IR,DR>  CR: 42042048  XER: 20000000
TASK = c3889bd0[392] 'I2CEEpromTest' THREAD: c39aa000
GPR00: 00009000 c39abe20 c3889bd0 c39075c8 c39abe28 00000001 00000000 00000001
GPR08: c3889bd0 c39075c8 00009032 c39abe34 00002437
NIP [c01628f8] cpm_i2c_xfer+0x5fc/0x6d0
LR [c01628f0] cpm_i2c_xfer+0x5f4/0x6d0
Call Trace:
[c39abe20] [c0162924] cpm_i2c_xfer+0x628/0x6d0 (unreliable)
[c39abe90] [c015f6a0] i2c_transfer+0x88/0xb4
[c39abeb0] [c0160164] i2c_master_recv+0x48/0x6c
[c39abed0] [c01618dc] i2cdev_read+0x50/0xe4
[c39abef0] [c0068b24] vfs_read+0xc4/0x108
[c39abf10] [c0068f4c] sys_read+0x4c/0x90
[c39abf40] [c000d348] ret_from_syscall+0x0/0x38
Instruction dump:
3bc00064 92610010 3bf201c8 92810014 3b61

This happen because though the wait_event_interruptible_timeout takes the
signals into account, the driver does not handle them.
We propose to change the wait_event_interruptible_timeout with
wait_event_timeout, leaving the signals to be handled in other points
on the upper layers.

Signed-off-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
[ben-linux@fluff.org: fix title for patch]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
15 years agoi2c-omap: Fix build breaking typo cpu_is_omap_2430
Tony Lindgren [Wed, 17 Jun 2009 10:20:21 +0000 (03:20 -0700)]
i2c-omap: Fix build breaking typo cpu_is_omap_2430

Hi Ben,

Can you please queue this fix?

Thanks,

Tony

>From ffe2b2cdf6283770b70a197e3748c6b40a1006be Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Wed, 17 Jun 2009 13:14:23 +0300
Subject: [PATCH] i2c-omap: Fix build breaking typo in cpu_is_omap_2430

Commit 84bf2c86 introduced a typo, it should be cpu_is_omap2430
instead. The typo was probably caused by a mismerge.

Without this patch all omaps fail to build with:
error: implicit declaration of function 'cpu_is_omap_2430'

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
Linus Torvalds [Sun, 21 Jun 2009 20:14:22 +0000 (13:14 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/drzeus/mmc

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  sdhci: remove needless double parenthesis
  sdhci: Specific quirk vor VIA SDHCI controller in VX855ES
  s3cmci: fix dma configuration call
  mmc: Add new via-sdmmc host controller driver
  sdhci: Add support for hosts that are only capable of 1-bit transfers
  MAINTAINERS: add myself as atmel-mci maintainer (sd/mmc interface)
  sdhci: Add SDHCI_QUIRK_NO_MULTIBLOCK quirk
  sdhci: Add better ADMA error reporting
  sdhci-s3c: Samsung S3C based SDHCI controller glue

15 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Linus Torvalds [Sun, 21 Jun 2009 20:14:07 +0000 (13:14 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: aes-ni - Remove CRYPTO_TFM_REQ_MAY_SLEEP from fpu template
  crypto: aes-ni - Do not sleep when using the FPU
  crypto: aes-ni - Fix cbc mode IV saving
  crypto: padlock-aes - work around Nano CPU errata in CBC mode
  crypto: padlock-aes - work around Nano CPU errata in ECB mode

15 years agoMerge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Sun, 21 Jun 2009 20:13:53 +0000 (13:13 -0700)]
Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  lockdep: Select frame pointers on x86
  dma-debug: be more careful when building reference entries
  dma-debug: check for sg_call_ents in best-fit algorithm too

15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Sun, 21 Jun 2009 20:13:08 +0000 (13:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Add model=6530g option
  ALSA: hda - Acer Inspire 6530G model for Realtek ALC888
  ALSA: snd_usb_caiaq: fix legacy input streaming
  ASoC: Kill BUS_ID_SIZE
  ALSA: HDA - Correct trivial typos in comments.
  ALSA: HDA - Name-fixes in code (tagra/targa)
  ALSA: HDA - Add pci-quirk for MSI MS-7350 motherboard.
  ALSA: hda - Fix memory leak at codec creation

15 years agoMove FAULT_FLAG_xyz into handle_mm_fault() callers
Linus Torvalds [Fri, 10 Apr 2009 16:01:23 +0000 (09:01 -0700)]
Move FAULT_FLAG_xyz into handle_mm_fault() callers

This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault().  All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoRemove internal use of 'write_access' in mm/memory.c
Linus Torvalds [Fri, 10 Apr 2009 15:43:11 +0000 (08:43 -0700)]
Remove internal use of 'write_access' in mm/memory.c

The fault handling routines really want more fine-grained flags than a
single "was it a write fault" boolean - the callers will want to set
flags like "you can return a retry error" etc.

And that's actually how the VM works internally, but right now the
top-level fault handling functions in mm/memory.c all pass just the
'write_access' boolean around.

This switches them over to pass around the FAULT_FLAG_xyzzy 'flags'
variable instead.  The 'write_access' calling convention still exists
for the exported 'handle_mm_fault()' function, but that is next.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoipc: unbreak 32-bit shmctl/semctl/msgctl
Johannes Weiner [Sat, 20 Jun 2009 00:23:29 +0000 (02:23 +0200)]
ipc: unbreak 32-bit shmctl/semctl/msgctl

31a985f "ipc: use __ARCH_WANT_IPC_PARSE_VERSION in ipc/util.h" would
choose the implementation of ipc_parse_version() based on a symbol
defined in <asm/unistd.h>.

But it failed to also include this header and thus broke
IPC_64-passing 32-bit userspace because the flag wasn't masked out
properly anymore and the command not understood.

Include <linux/unistd.h> to give the architecture a chance to ask for
the no-no-op ipc_parse_version().

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agosdhci: remove needless double parenthesis
Pierre Ossman [Sun, 21 Jun 2009 18:59:33 +0000 (20:59 +0200)]
sdhci: remove needless double parenthesis

Signed-off-by: Pierre Ossman <pierre@ossman.eu>
15 years agosdhci: Specific quirk vor VIA SDHCI controller in VX855ES
Harald Welte [Thu, 18 Jun 2009 14:53:38 +0000 (16:53 +0200)]
sdhci: Specific quirk vor VIA SDHCI controller in VX855ES

The SDHCI controller found in the VX855ES requires 10ms
delay between applying power and applying clock.

This issue has been discovered and documented by the OLPC XO1.5 team.

Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
15 years agos3cmci: fix dma configuration call
Ben Dooks [Mon, 8 Jun 2009 22:33:56 +0000 (23:33 +0100)]
s3cmci: fix dma configuration call

This was missed in the DMA changes during the s3c24xx
updates in commit 8970ef47d56fd3db28ee798b9d400caf08abd924.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
15 years agommc: Add new via-sdmmc host controller driver
Harald Welte [Wed, 17 Jun 2009 18:22:39 +0000 (20:22 +0200)]
mmc: Add new via-sdmmc host controller driver

This adds the via-sdmmc driver for the SD/MMC-controller of VIA,
which is found in a number of recent integrated VIA chipset
products.

Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
15 years agosdhci: Add support for hosts that are only capable of 1-bit transfers
Anton Vorontsov [Wed, 17 Jun 2009 20:14:08 +0000 (00:14 +0400)]
sdhci: Add support for hosts that are only capable of 1-bit transfers

Some hosts (hardware configurations, or particular SD/MMC slots) may
not support 4-bit bus. For example, on MPC8569E-MDS boards we can
switch between serial (1-bit only) and nibble (4-bit) modes, thought
we have to disable more peripherals to work in 4-bit mode.

Along with some small core changes, this patch modifies sdhci-of
driver, so that now it looks for "sdhci,1-bit-only" property in the
device-tree, and if specified we enable a proper quirk.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
15 years agoMAINTAINERS: add myself as atmel-mci maintainer (sd/mmc interface)
Nicolas Ferre [Tue, 16 Jun 2009 11:05:50 +0000 (13:05 +0200)]
MAINTAINERS: add myself as atmel-mci maintainer (sd/mmc interface)

Add MAINTAINERS entry for atmel-mci driver.
This driver was maintained by its author: Haavard Skinnemoen. I take the
maintainance of it.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
15 years agosdhci: Add SDHCI_QUIRK_NO_MULTIBLOCK quirk
Ben Dooks [Sun, 14 Jun 2009 11:40:53 +0000 (12:40 +0100)]
sdhci: Add SDHCI_QUIRK_NO_MULTIBLOCK quirk

Add quirk to show the controller cannot do multi-block IO.

This is mainly for the Samsung SDHCI controller that currently
cannot manage to do multi-block PIO without timing out.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>