[netdrvr] convert sbmac tx to spin_lock_irqsave to prevent early IRQ enable

Netpoll will call the interrupt handler with interrupts
disabled when using kgdboe, so spin_lock_irqsave() should
be used instead of spin_lock_irq() to prevent interrupts
from being incorrectly enabled.

Signed-off-by: Weiwei Wang <weiwei.wang@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

fs-enet: remove code associated with !CONFIG_PPC_MERGE

Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove
the dead code associated with !CONFIG_PPC_MERGE.

With this change the pre_request_irq() and post_free_irq() calls became
nops so they have been removed.  Also removed fs_request_irq() and
fs_free_irq() and just called request_irq() and free_irq().

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

netdev: drop CONFIG_PPC_MERGE from Kconfig

Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms so we don't need to depend on it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

atl2: add tx bytes statistic

Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

forcedeth fix: take phy out of reset during power up

This patch will add the phy reset bit into the power up mask which is
used during power up. Certain BIOSes will place the phy in reset and
therefore the driver must take the phy out of reset when it loads.

Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

e1000e: avoid duplicated output of device name in kernel warning

With 2.6.27-rc3 I noticed the following messages in my boot log:

0000:01:00.0: 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
0000:01:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:16:76:04:ff:09

The second seems correct, but the first has a silly repetition of the
PCI device before the actual message. The message originates from
e1000_eeprom_checks in e1000e/netdev.c.

With this patch below the first message becomes

  e1000e 0000:01:00.0: Warning: detected DSPD enabled in EEPROM

which makes it similar to directly preceding messages.

Use dev_warn instead of e_warn in e1000_eeprom_checks() as the interface
name has not yet been assigned at that point.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

atl1e: remove the unneeded (struct atl1e_adapter *)

Remove the unneeded (struct atl1e_adapter *) casts, for hw->adapter
already has type atl1e_adapter *.

Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

gianfar: free/iounmap memory after an error in mii bus initialization

Recent changes to MII bus initialization code added exit points which
didn't free or iounmap the bus before returning.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11372.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Reported-by: Daniel Marjamki <danielm77@spray.se>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ne.c: fix rmmod, platform driver improvements

Removing the module would cause a kernel oops as platform_driver_probe
failed to detect a device and unregistered the platform driver on module
init, and cleanup_module would unregister the already unregistered driver.
The suspend and resume functions weren't being called.

platform_driver support was added earlier, but without any
platform_device_register* calls I don't think it was being used.  Now all
devices are registered using platform_device_register_simple and pointers
are kept to unregister the ones that the probe failed for or unregister
all devices on module shutdown.  init_module no longer calls ne_init to
reduce confusion (and multiple unregister paths that caused the rmmod
oops).  With the devices now registered they are added to the platform
driver and get suspend and resume events.

netif_device_detach(dev) was added before unregister_netdev(dev) when
removing the region as occationally I would see a race condition where the
device was still being used in unregister_netdev.

Signed-off-by: David Fries <david@fries.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

gianfar: Fix error in mdio reset timeout

The loop with the timeout used "while (...  && timeout--)", which means
than when the timeout occurs, "timeout" will be -1 after the loop has
exited.  The code that checks if the looped exited because of a timeout
used "if (timeout <= 0)".  Seems ok, except timeout is unsigned, and
(unsigned)-1 isn't less than zero!

Using "--timeout" in the loop fixes this problem, as now "timeout" will be
0 when the loop times out.

This also fixes a bug in the existing code, where it will erroneously think
a timeout occurred if the condition the loop was waiting for is satisfied
on the final iteration before a timeout.

Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

e1000e: remove failed request for sw/fw/hw flag

When the driver fails to acquire the control flag used to serialize
NVM and PHY accesses between the driver, firmware and hardware, remove the
request for the flag otherwise the hardware might grant the flag when it
becomes available but the driver will not release the flag.  This could
cause the firmware to prevent the driver getting the flag for all future
attempts.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

enic: bug fix: don't set netdev->name too early

Bug fix: don't set netdev->name early before netdev registration.  Setting
netdev->name early with dev_alloc_name() would occasionally cause netdev
registration to fail returning error that device was already registered.
Since we're using netdev->name to name MSI-X vectors, we now need to
move the request_irq after netdev registartion, so move it to ->open.

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

enic: Bug fix: Free MSI intr with correct data handle

Bug fix: Free MSI intr with correct data handle
Use davem proposed naming for MSI-X tx/rx vectors (ethX-tx-0, ethX-rx-0)

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

enic: fixes for review items from Ben Hutchings

Fixes for review items from Ben Hutchings:
 - use netdev->net_stats rather than private net_stats
 - use ethtool op .get_sset_count rather than .get_stats_count
 - err out if setting Tx/Rx csum or TSO using ethtool and setting is
   not enabled for device.
 - pass in jiffies + constant to round_jiffies
 - return err if new MTU is out-of-bounds

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

enic: Don't indicate IPv6 pkts using soft-LRO

LRO is only applied to IPv4 pkts, so don't use the LRO indication functions
for anything other IPv4 pkts.  Every non-IPv4 pkt is indicated using non-
LRO functions.

Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

r6040: fix wrong assignment in r6040_free_txbufs

This patch fixes a wrong assignment in r6040_free_txbufs
on a receive skb pointer while we should actually do this
on the transmit skb pointer.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

qeth: avoid qeth recovery problems

Do not touch IFF_UP flag during qeth recovery, but invoke dev_close()
in case of failing recovery.
Cancel outstanding control commands in case of Data Checks or
Channel Checks.
Do not invoke qeth_l2_del_all_mc() in case of a hard stop to speed up
removal of qeth devices.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

qeth: use firmware MAC-address for layer2 hsi-devices

Real HiperSocket devices in layer2 mode have a firmware-created
MAC-address. This change enables the qeth driver to use this
firmware MAC-address for layer2 HiperSocket devices.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Merge branch 'for-2.6.28' of git://git.marvell.com/mv643xx_eth into upstream-next

Merge branch 'davem-next' of /linux/kernel/git/jgarzik/netdev-2.6

bonding: add more ethtool support

This patch allows reporting the link, checksum, and feature settings
of bonded device by using generic hooks.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

netxen: enable msi-x for quad-gig boards

NX3031 firmware now supports MSI-X interrupts on Quad GbE boards.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sundance: set carrier status on link change events

Check if the link is available when a changed interrupt has been received and
set the carrier status appropriately.  The code is copied nearly verbatim from
the dl2k module.  The link status could be used in more places in the driver,
but this is enough to get the carrier status reported to userspace.  Fixes
kernel bug #7487:

    http://bugzilla.kernel.org/show_bug.cgi?id=7487

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

drivers/net: replace __FUNCTION__ with __func__

__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ehea: Enable DLPAR memory remove

This patch adds the capability flag to the capability list for dynamic LPAR
memory remove to enable this feature.

Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

[netdrvr] usb/hso: throttle to prevent loss of serial data

Patch to stop loss of characters on the hso modems,
this patch throttles & unthrottles the modem by
not putting out urbs until the tty/line discipline layer
has enough space for newly received packets.
serial ports. This is required for firmware diagnostics
being done at Option.

Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

myri10ge: use DCA if DCA is compiled as a module

Use DCA in myri10ge when CONFIG_DCA_MODULE is set as well.

And thus force INTEL_IOATDMA to =y so that DCA=y if we are =y.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

cxgb3 - remove duplicate tests in lro

The generic lro code checks TCP flags/options.
Remove duplicate tests done in the driver.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

r8169: select MII in Kconfig

drivers/built-in.o: In function `rtl8169_gset_xmii':
r8169.c:(.text+0x82259): undefined reference to `mii_ethtool_gset'

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ehea: fix mutex and spinlock use

  Looks like to me that the ehea_fw_handles.lock mutex and the
ehea_bcmc_regs.lock spinlock are taken much longer than necessary and could
as well be pushed inside the functions that need them
(ehea_update_firmware_handles() and ehea_update_bcmc_registrations())
rather than at each callsite.

Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix DCA dependency in Kconfig

ixgbe can depend on dca IF it is enabled.  So if we are compiled as
IXGBE=y, and DCA is enabled, then we must force INTEL_IOATDMA and therefore
DCA to be =y also.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: whitespace/formatting cleanup

This patch cleans up some whitespace items, reorders a couple of functions, and removes some outdated comments.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: correctly add and remove napi queues

This patch corrects support for NAPI so that queues are correctly added and
removed during suspend/resume in the event that the number of MSI-X vectors
changes.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Whitespace, copyright update and version number change patch

This patch cleans up a bit of whitespace issues with the driver, updates
the copyright information, and bumps the version number up.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: bump version

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: xmit frame refactor

ixgbe_xmit_frame can be refactored to use fewer locals and better
utilize common kernel macros.

also fixed minor buglet with internal to driver vlan flag variable being
passed incorrectly.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: lower stack space usage

some functions were un-necessarily using local variables.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: cleanup defines

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: move set_num_queues and call it after msix failure

This is partial preparation for a future patch which will extend
ixgbe_set_num_queues

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: refresh the ixgbe_down function

clean up the hardware shutdown sequence to prevent hardware
from continuing to send when resetting or unloading.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: update to latest common code module

This is a massive update that includes infrastructure for further patches
where we will add support for more phy types and eeprom types.

This code is shared as much as possible with other drivers, so the code may
seem a little obtuse at times but wherever possible we keep to the linux
style and methods.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: add clean rx many routine

in some configurations there can be more than one rx queue per vector
in msi-x mode.  Add functionality to be able to clean this without
changing the performance path single-rx-queue cleanup.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: lro stats were not counted on first ethtool -Scall

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix ring reallocation in ethtool

changing ring sizes in ethtool needs to be robust.  If an allocation fails the
driver must continue operation, with the previous settings.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: add device support for XF LR adapters

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: recycle pages in packet split mode

most of the time we only need 1500 bytes for a packet which means
we don't need a whole 4k page for each packet.  Share the allocation
by using a reference count to the page and giving half to two
receive descriptors.  This can enable us to use packet split mode
all the time due to the performance increase of allocating half
the pages.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix bug with lots of tx queues

when using more than 8 tx queues you can overrun the 8 bit v_idx
field, so change it to 16 bits to represent the maximum number
of queues (one for each bit)

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix initial interrupt throttle settings

ixgbe was incorrectly setting the throttle rate setting for all tx
queues and the driver has been refreshed to better handle a dynamic
interrupt mode as well as multiple queues.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix ethtool disable csum for ipv6

ethtool was not disabling the correct netif flags when setting
checksum disable.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix pci_resource allocation as in other drivers

Form: Jesse Brandeburg <jesse.brandeburg@intel.com>

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix ethtool register dump

1) reading some of the registers in our hardware causes them to clear,
so don't read ICR in the ethtool register dump function.
2) several register iterators were not iterating

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: limit small mtu to minimum for ipv4 support

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix bug with shared interrupts

fix ixgbe bug reported with shared legacy interrupts

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: link change interrupt was not causing link event

Upon review a buglet was found where link change was not causing
an immediate link change event as it should.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: Update watchdog thread to accomodate longerlink_up events

This patch updates the link_up code and watchdog thread so that link_up
doesn't cause stack overflows due to long waits in interrupt context.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix multicast address update

after the most recent patches, the driver was not using the
correct iterator for updating the receive address registers (RAR)

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix dca defines to not have spaces

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ixgbe: fix bug where using wake queue instead of start

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

netxen: add pci ids

Define old and new pci vendor and device ids.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

myri10ge: Rename DCA-related firmware counters

Rename the cryptic "dca_capable" to "dca_capable_firmware"
and "dca_enabled" to "dca_device_present" in the firmware
counters.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

myri10ge: Stop scaring people when DCA is built but absent

Stop scaring people with what looks like a fatal message when DCA support
is compiled into their kernel, but the DCA device is not present.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

smc911x: remove duplicate debug printout

Remove duplicated debug printout.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

r6040: fix bad usage of udelay

This patch fixes the bad usage of udelay(5000), which in turns is a
mdelay(5). It causes compilation for ARM where udelay maximum value
is checked.

Reported-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Fix type of FALCON_SPI_MAX_LEN

FALCON_SPI_MAX_LEN has type size_t while other SPI lengths have type
unsigned int.  This results in warnings from min() on 64-bit
architectures where they are different.  Add a cast to make it match.

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Use CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS where appropriate

For some buffers we use a starting offset of either NET_IP_ALIGN or 0
depending on whether we believe the architecture supports efficient
access to unaligned words.  There is now a config macro specifying
whether this is the case, so check that rather than checking for
specific architectures.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove obsolete comment about PCI modes

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Disable interrupts after a fatal interrupt occurs until reset

This should avoid an interrupt storm, which has been observed in the
field with one faulty board.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Insert read memory barrier after checking MAC statistics flag

This prevents speculative reading of the statistics before the
completion flag.

From: Neil Turton <nturton@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Stop generating bogus events in tenxpress_check_hw()

mdio_clause45_links_ok() correctly checks efx_phy_mode_disabled(), so
tenxpress_link_ok() doesn't need to.

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Don't include net_driver.h from falcon_io.h

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Make queue flushes more reliable

Increase the potential retry count for RX flushes from 5 to 100.

Stop polling the RX_DESC_PTR_TBL to infer that a flush might have
happened. Instead absolutely rely on the flush events, unless bug 7803
applies (Falcon rev A only).

To keep things quick, request flushes for every TX and RX queue up
front, and match up the events to requests.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Don't use EFX_OWORD_FIELD on an event (64-bit, quad-word)

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Serialise tenxpress_special_reset() with statistics fetches

On some boards 10Xpress feeds a 156 MHz clock to the Falcon XMAC.  MAC
statistics DMA can fail while this clock is stopped during a PHY reset.

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Remove workaround for old firmware bug

There was a bug in XAUI synchronisation in early 10Xpress firmware
versions.  This is fixed in released firmware and we do not need to
work around it.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Fix memory BAR release call on error path

Match pci_request_region() with pci_release_region(), not
release_mem_region().

From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sfc: Add check for memory allocation failure in falcon_probe_nic()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

8139too: [cosmetic] fix incorrect register for flash-rom

I would like to submit a correction to the driver

     drivers/net/8139too.c,

which in no way changes the compiled driver, but does change
the value of a previously incorrect value for the configuration
register address of Flash PROM on the network processor rtl8139C.
This corrected value is in accordance with the datasheet
for rtl8139C, and in addition this new value is indeed used
in other functional drivers that use this adapter for
programming a Flash memory chip in situ. But as said,
the two new constants are never referenced in the driver
maintained by you: they are only informational and correct!

Mats Erik Andersson, meand@users.sourceforge.net

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

s2io: Fix enabling VLAN tag stripping at driver initialization

VLAN doesn't work except if you'd opened the interface in promiscuous
mode before.  This happens because VLAN tag stripping is not correctly
marked as enabled at device startup

Also, the vlan_strip_flag field was moved to the private network
structure.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

cs89x0: fix warning release_irq label

release_irq label is only used when ALLOW_DMA is defined.

drivers/net/cs89x0.c: In function 'net_open':
drivers/net/cs89x0.c:1401: warning: label 'release_irq' defined but not used

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

[netdrvr/usb] hso_create_bulk_serial_device(): fix a double free

hso_serial_common_free() mustn't be called if
hso_serial_common_create() fails.

Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

wan/hdlc_x25.c: fix a NULL dereference

WAN: fixes a NULL dereference in hdlc_x25.

Reported-by: Adrian Bunk <bunk@kernel.org>.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

bonding: Do not tx-balance some IPv6 packets on ALB/TLB bonds

IPv6 all-node-multicasts and DAD probes should not be tx-balanced
on ALB/TLB bonds.  The all-node-multicast is an equivalent to IPv4
broadcasts.  DAD probes have to be sent only on the primary so that
we don't get false-positive detections.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

[netdrvr] atl1e: Don't take the mdio_lock in atl1e_probe

Lockdep warns about the mdio_lock taken with interrupts enabled then later
taken from interrupt context.  Initially, I considered changing these
to spin_lock_irq/spin_unlock_irq, but then I looked at atl1e_phy_init()
and saw that it calls msleep().  Sleeping while holding a spinlock is
not allowed either.

In the probe path, we haven't registered the interrupt handler, so
it can't poke at this card yet.  It's before we call register_netdev(),
so I don't think any other threads can reach this card either.  If I'm
right, we don't need a spinlock at all.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ehea: Fix DLPAR memory handling

The ehea busmap must be allocated only once in the first of many calls of the
ehea_create_busmap_callback.

Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

[netdrvr] ne: Fix suspend and resume for ISA PnP cards.

A call to pnp_stop_dev and pnp_start_dev now shuts down and
initializes plug and play devices for suspend and resume.

Signed-off-by: David Fries <david@fries.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

[netdrvr] au1000_eth: Spinlock initialisation fix

Seems like the spinlock for the AU1x00 ethernet device is initialised too
late, as it is already used in enable_mac(), which is called via
mii_probe() before the init takes place.

The attached patch is working here for a Linux Au1100 2.6.22.6 kernel,
and as far as I checked should also be applicable to the current head
(just line numbers differ).

Signed-off-by: Martin Gebert <Martin.Gebert@alpha-bit.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

MAINTAINERS: add Atheros maintainer for atlx

Jie Yang at Atheros is getting more directly involved with upstream work on the
atl* drivers.  This patch changes the ATL1 entry to ATLX (atl2 support posted
to netdev today) and adds him as a maintainer.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

drivers/net/mlx4/alloc.c needs mm.h

sparc32 allmodconfig with linux-next:

drivers/net/mlx4/alloc.c: In function 'mlx4_buf_alloc':
drivers/net/mlx4/alloc.c:164: error: 'PAGE_KERNEL' undeclared (first use in this function)
drivers/net/mlx4/alloc.c:164: error: (Each undeclared identifier is reported only once
drivers/net/mlx4/alloc.c:164: error: for each function it appears in.)

this is due to some header shuffle in linux-next.  I didn't look to see what
it was.  I'd sugges that this patch be merged ahead of a linux-next merge to
avoid bisection breaks.

We strictly only need asm/pgtable.h, but going direct to asm includes always
seems grubby.

Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

drivers/net/skfp/pmf.c: Use offsetof() macro

Self-baked macros cause bunch of compile warnings like below:

  CC [M]  drivers/net/skfp/pmf.o
  CC      net/ipv4/fib_semantics.o
drivers/net/skfp/pmf.c:86: warning: cast from pointer to integer of different size
drivers/net/skfp/pmf.c:87: warning: cast from pointer to integer of different size
...

Use the standard offsetof() macro instead.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

smc91x: SMC_IO_SHIFT platform data support for default case

Commit 159198862adad7109bb347bb30a620f67beac45f added SMC_IO_SHIFT
platform data support. After that ARM board support was added.

The default case is still missing though, so on SuperH SMC_IO_SHIFT
is constantly zero regardless of what you pass as platform data.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Test-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

smc91x: fix nowait printout

Commit c4f0e76747e80578a8f7fddd82fd0ce8127bd2f8 added nowait platform
data support. The printout code was however not updated, so the value
of SMC_NOWAIT is still used. This patch makes sure that nowait is printed
accordingly to platform data.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

r8169: fix RxMissed register access

- the register is defined for the 8169 chipset only and there is
  no 8169 beyond RTL_GIGA_MAC_VER_06.
- only the lower 3 bytes of the register are valid

Fixes:
1. http://bugzilla.kernel.org/show_bug.cgi?id=10180
2. http://bugzilla.kernel.org/show_bug.cgi?id=11062 (bits of)

Tested by Hermann Gausterer and Adam Huffman.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ehea: fix phyp debugging typo

  Fix typo in ehea_h_query_ehea() which prevents building when DEBUG is on.

Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

tulip: Fix dead 21041 ethernet after ifconfig down

The de2104x did a pci_disable_device() in it's close function, but
the open function never does a pci_enable_device() and assumes that
the device is already enabled. Considering that downing the interface
is just a temporary thing the pci_disable_device() isn't a pretty good
idea and removing it from the close function just fixes the bug.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

net: remove ifalias on empty given alias

This patch removes the potentially allocated ifalias when the (new) given alias is empty.

E.g. when setting

echo "" > /sys/class/net/eth0/ifalias

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

aoe: Fix OOPS after SKB queue changes.

Reported by Thomas Graf.

If we don't unlink the SKB from the queue when we send it
out in aoenet_xmit(), dev_hard_start_xmit() will see skb->next
as non-NULL and interpret this to mean the SKB is part of a
GSO segment list.

Add __skb_unlink() call to fix that.

Signed-off-by: David S. Miller <davem@davemloft.net>

can: Add documentation for virtual CAN driver usage

This patch adds a usage documentation for the virtual CAN driver (vcan).

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: Fix queue traversal in tcp_use_frto().

We must check tcp_skb_is_last() before doing a tcp_write_queue_next().

Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: Fix order of tests in tcp_retransmit_skb()

tcp_write_queue_next() must only be made if we know that
tcp_skb_is_last() evaluates to false.

Signed-off-by: David S. Miller <davem@davemloft.net>

ppp_generic: Use skb_peek() in ppp_receive_mp_frame().

Signed-off-by: David S. Miller <davem@davemloft.net>