Arnd Bergmann [Tue, 3 Sep 2019 14:08:40 +0000 (16:08 +0200)]
Merge tag 'imx-dt-5.4' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm32 device tree changes for 5.4:
- New board support: ZII i.MX7 RMU2, Kontron i.MX6UL N6310, and
PHYTEC phyBOARD-Segin based on i.MX6ULL.
- A series from Andrey Smirnov to update vf610-zii boards on I2C
pinmux, switch watchdog, GPIO expander IRQ.
- Move GIC node into soc node for i.MX6 SoCs.
- Add OV5645 camera support for imx6qdl-wandboard board.
- Drop unneeded snvs_pwrkey node for imx7d-zii-rpu2 and imx7-colibri.
- Use simple-mfd instead of simple-bus for i.MX6 ANATOP.
- Move the native-mode property inside the display-timings node for
various i.MX25 and i.MX27 boards.
- Add EDMA devices for i.MX7ULP SoC.
- A series from Stefan Riedmueller to update imx6ul-phytec-segin board
on various devices.
- Use OF graph to describe the display for opos6uldev board.
- Misc random updates on i.MX7/6 boards.
* tag 'imx-dt-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: vf610-zii-scu4-aib: Configure IRQ line for GPIO expander
ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards
ARM: dts: vf610-zii-cfu1: Slow I2C0 down to 100 kHz
ARM: dts: pbab01: correct rtc vendor
ARM: vf610-zii-cfu1: Add node for switch watchdog
ARM: dts: imx6: drop gpmi-nand address and size cells
ARM: dts: imx6: replace simple-bus by simple-mfd for anatop
ARM: dts: imx6qdl-colibri: add phy to fec
ARM: dts: imx7-colibri: add recovery for I2C for iMX7
ARM: dts: imx7-colibri: Add sleep pinctrl to ethernet
ARM: dts: imx7-colibri: prepare module device tree for FlexCAN
ARM: dts: imx7-colibri: disable HS400
ARM: dts: imx7-colibri: make sure module supplies are always on
ARM: dts: imx7d: cl-som-imx7: add compatible for phy
ARM: dts: imx7d: cl-som-imx7: make ethernet work again
ARM: dts: imx6ul: Add csi node
ARM: dts: imx25: mbimxsd25: native-mode is part of display-timings
ARM: dts: apf27dev: native-mode is part of display-timings
ARM: dts:
edb7211: native-mode is part of display-timings
ARM: dts: imx27-phytec-phycore-rdk: native-mode is part of display-timings
...
Link: https://lore.kernel.org/r/20190825153237.28829-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 14:06:07 +0000 (16:06 +0200)]
Merge tag 'imx-dt-clkdep-5.4' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree update with new clocks:
- A series from Anson Huang to add i.MX8MN SoC and DDR4 EVK board
device tree support.
- Add DSP device tree support for i.MX8QXP SoC.
* tag 'imx-dt-clkdep-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8qxp: Add DSP DT node
arm64: dts: imx8mn: Add cpu-freq support
arm64: dts: imx8mn-ddr4-evk: Add rohm,
bd71847 PMIC support
arm64: dts: imx8mn-ddr4-evk: Add i2c1 support
arm64: dts: freescale: Add i.MX8MN DDR4 EVK board support
arm64: dts: imx8mn: Add gpio-ranges property
arm64: dts: freescale: Add i.MX8MN dtsi support
clk: imx8: Add DSP related clocks
clk: imx: Add support for i.MX8MN clock driver
clk: imx: Add API for clk unregister when driver probe fail
clk: imx8mm: Make 1416X/1443X PLL macro definitions common for usage
dt-bindings: imx: Add clock binding doc for i.MX8MN
Link: https://lore.kernel.org/r/20190825153237.28829-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 14:03:47 +0000 (16:03 +0200)]
Merge tag 'imx-bindings-5.4' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT bindings update for 5.4
- Add SoC bindings for i.MX8MN.
- Add board bindings for pico-pi-imx8m, Hummingboard Pulse, imx8mq
nitrogen, i.MX8QXP AI_ML, ls1046a-frwy etc.
- Add vendor prefix for Anvo-Systems and Einfochips.
- Update LPUART bindings for i.MX8QXP clock requirement.
- Update imx-weim bindings for optional burst clock mode support.
- Update EEPROM bindings for Anvo ANV32E61W device support.
* tag 'imx-bindings-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: Add Kontron i.MX6UL N6310 compatibles
dt-bindings: eeprom: at25: Add Anvo ANV32E61W
dt-bindings: vendor-prefixes: Add Anvo-Systems
dt-bindings: arm: fsl: add Hummingboard Pulse
dt-bindings: arm: imx: add imx8mq nitrogen support
dt-bindings: fsl: dspi: Add fsl,ls1088a-dspi compatible string
dt-bindings: arm: imx: Add the soc binding for i.MX8MN
dt-bindings: bus: imx-weim: document optional burst clock mode
dt-bindings: arm: fsl: Add the pico-pi-imx8m board
dt-bindings: arm: Document i.MX8QXP AI_ML board binding
dt-bindings: Add Vendor prefix for Einfochips
dt-bindings: arm: nxp: Add device tree binding for ls1046a-frwy board
dt-bindings: serial: lpuart: add the clock requirement for imx8qxp
dt-bindings: arm: fsl: Add support for ZII i.MX7 RMU2 board
Link: https://lore.kernel.org/r/20190825153237.28829-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 14:01:58 +0000 (16:01 +0200)]
Merge tag 'aspeed-5.4-devicetree' of git://git./linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.4
New machines:
- Facebook Wedge100, Wedge40 and Minipack
- Lenovo Hr855xg2
- Wistron Mihawk
There's a few other updates, notably some changes to to use the newly
added SDHCI driver.
* tag 'aspeed-5.4-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: swift: Add eMMC device
ARM: dts: aspeed: Enable first MMC slot on AST2500 EVB
ARM: dts: aspeed: Describe SD controllers
ARM: dts: aspeed: Add Mihawk BMC platform
ARM: dts: aspeed: fp5280g2: Fix power supply address
ARM: dts: aspeed: tiogapass: Add Riser card
ARM: dts: aspeed: tiogapass: Move battery sensor
ARM: dts: aspeed: Add Facebook Wedge100 BMC
ARM: dts: aspeed: Add Facebook Wedge40 BMC
ARM: dts: aspeed: swift: Fix FSI GPIOs
ARM: dts: aspeed: Add SGPM pinmux
ARM: dts: aspeed: tiogapass: Add VR devices
ARM: dts: aspeed: Add Lenovo Hr855xg2 BMC
ARM: dts: aspeed: Add Facebook Minipack BMC
Link: https://lore.kernel.org/r/CACPK8XfKHpNYXNE_VRaLeGUQa7-hkmUS0nsPfaeSLE4sckKFHg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 14:01:08 +0000 (16:01 +0200)]
Merge tag 'omap-for-v5.4/dt-take2-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
dts changes for omap variants for v5.4
Remove regulator-boot-off properties that we never had in the mainline
kernel so they won't do anything. We add stdout-path for gta04, and
make am335x-boneblue use am335x-osd335x-common.dtsi file.
* tag 'omap-for-v5.4/dt-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblue: Use of am335x-osd335x-common.dtsi
ARM: dts: gta04: define chosen/stdout-path
ARM: dts: omap3-n950-n9: Remove regulator-boot-off property
ARM: dts: am335x-cm-t335: Remove regulator-boot-off property
Link: https://lore.kernel.org/r/pull-1566599057-142651@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:59:42 +0000 (15:59 +0200)]
Merge tag 'v5.3-next-dts64' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
mt8183:
- fix pwrap interrupt number
- add i2c notes
dt-bindings:
- add compatible for mt6779
- add mt6779 uart and sysirq compatible
* tag 'v5.3-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: irq: mtk, sysirq: add support for mt6779
dt-bindings: mtk-uart: add mt6779 uart bindings
dt-bindings: mediatek: add support for mt6779 reference board
arm64: dts: mt8183: add I2C nodes
arm64: dts: mt8183: fix pwrap gic number
Link: https://lore.kernel.org/r/def8fb77-fce4-097d-7ae2-8c4670bc09c1@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:57:35 +0000 (15:57 +0200)]
Merge tag 'v5.3-next-dts32' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
add support for the mt7629 reference board
* tag 'v5.3-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm: dts: mediatek: add basic support for MT7629 SoC
Link: https://lore.kernel.org/r/e236f659-2851-21b8-1873-314cd72ed6be@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:55:50 +0000 (15:55 +0200)]
Merge tag 'sunxi-dt-for-5.4-1' of git://git./linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.4
Our usual pile of patches for the next release, which include mostly:
- More fixes thanks to the DT validation using the YAML bindings
- IR receiver support on the H6
- SPDIF support on the H6
- I2C Support on the H6
- CSI support on the A20
- RTC support on the H6
- New Boards: Lichee Zero Plus, Tanix TX6, A64-Olinuxino-eMMC
* tag 'sunxi-dt-for-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (40 commits)
arm64: dts: allwinner: orange-pi-3: Enable WiFi
ARM: dts: sunxi: Add missing watchdog clocks
ARM: dts: sunxi: Add missing watchdog interrupts
arm64: dts: allwinner: h6: Add support for RTC and fix the clock tree
ARM: dts: sun7i: Add CSI0 controller
arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)
dt-bindings: arm: sunxi: Add compatible for A64 OlinuXino with eMMC
ARM: dts: v3s: Change the timers compatible
ARM: dts: h3: Change the timers compatible
ARM: dts: a83t: Change the timers compatible
ARM: dts: a23/a33: Change the timers compatible
ARM: dts: sun6i: Add missing timers interrupts
ARM: dts: sun5i: Add missing timers interrupts
ARM: dts: sun4i: Add missing timers interrupts
dt-bindings: mfd: Convert Allwinner GPADC bindings to a schema
arm64: dts: allwinner: h6: Introduce Tanix TX6 board
dt-bindings: arm: sunxi: Add compatible for Tanix TX6 board
arm64: allwinner: h6: add I2C nodes
dt-bindings: i2c: mv64xxx: Add compatible for the H6 i2c node.
ARM: dts: sunxi: Add mdio bus sub-node to GMAC
...
Link: https://lore.kernel.org/r/d97e6252-9dd7-4cf5-a3cf-56f78b0ca455.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:54:23 +0000 (15:54 +0200)]
Merge tag 'renesas-dt-bindings-for-v5.4-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.4 (take two)
- Renesas DT binding doc filename cleanups,
- R-Car Gen3 and RZ/G1 updates for the R-Car CAN and CANFD DT
bindings.
* tag 'renesas-dt-bindings-for-v5.4-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: can: rcar_can: document r8a77470 support
dt-bindings: can: rcar_canfd: document r8a77995 support
dt-bindings: can: rcar_can: document r8a77995 support
dt-bindings: can: rcar_can: document r8a77990 support
dt-bindings: rcar-{csi2,vin}: Rename bindings documentation files
dt-bindings: rcar-imr: Rename bindings documentation file
dt-bindings: Rename file of DT bindings for Renesas memory controllers
Link: https://lore.kernel.org/r/20190823123643.18799-6-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:37:05 +0000 (15:37 +0200)]
Merge tag 'renesas-arm64-dt-for-v5.4-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM64 DT updates for v5.4 (take two)
- Sort nodes in various SoC and board DTSes,
- HDMI sound for HiHope RZ/G2M and R-Car M3-N Salvator-X(S) boards,
- Limit EtherAVB to 100Mbps on the Ebisu and Draak boards,
- Small fixes and improvements.
* tag 'renesas-arm64-dt-for-v5.4-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (21 commits)
arm64: dts: renesas: Update 'vsps' properties for readability
arm64: dts: renesas: r8a77965-salvator-x(s): Enable HDMI sound
arm64: dts: renesas: r8a774c0: Fix register range of display node
arm64: dts: renesas: r8a77970: Sort nodes
arm64: dts: renesas: r8a7796: Sort nodes
arm64: dts: renesas: r8a774c0: Sort nodes
arm64: dts: renesas: r8a774c0: cat874: Sort nodes
arm64: dts: renesas: r8a774a1: Sort nodes
arm64: dts: renesas: r8a77980: Fix IPMMU-VC0 base address
arm64: dts: renesas: ebisu, draak: Limit EtherAVB to 100Mbps
arm64: dts: renesas: hihope-common: Add HDMI audio support
arm64: dts: renesas: r8a774c0: cat874: Add definition for 12V regulator
arm64: dts: renesas: r8a774c0: Point LVDS0 to its companion LVDS1
arm64: dts: renesas: r8a77995: Sort nodes
arm64: dts: renesas: r8a77995: draak: Sort nodes
arm64: dts: renesas: r8a77990: Sort nodes
arm64: dts: renesas: r8a77990: ebisu: Sort nodes
arm64: dts: renesas: r8a77980: v3hsk: Sort nodes
arm64: dts: renesas: r8a77980: condor: Sort nodes
arm64: dts: renesas: r8a77970: v3msk: Sort nodes
...
Link: https://lore.kernel.org/r/20190823123643.18799-4-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:33:24 +0000 (15:33 +0200)]
Merge tag 'renesas-arm-dt-for-v5.4-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.4
- Fix HSCIF PM Domain on R-Car H1,
- PMU support for RZ/G1C.
* tag 'renesas-arm-dt-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: r8a77470: Add PMU device node
ARM: dts: r8a7779: Use SYSC "always-on" PM Domain for HSCIF
Link: https://lore.kernel.org/r/20190823123643.18799-2-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:14:53 +0000 (15:14 +0200)]
Merge tag 'amlogic-dt64' of git://git./linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: Amlogic updates for v5.4
Highlights
- new SoCs (G12B family): S922X, A311D
- new SoCs (SM1 family): S905X3
- new board: SEI Robotics SEI610 (SM1/S905X3)
- new board: Khadas VIM3 (G12B/A311D)
- DVFS/CPUfreq support on G12[AB] family
* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (40 commits)
arm64: dts: add support for SM1 based SEI Robotics SEI610
dt-bindings: arm: amlogic: add SEI Robotics SEI610 bindings
dt-bindings: arm: amlogic: add SM1 bindings
arm64: dts: meson-g12b-odroid-n2: enable DVFS
arm64: dts: meson-g12b-khadas-vim3: add initial device-tree
dt-bindings: arm: amlogic: fix x96-max/sei510 section in amlogic.yaml
arm64: dts: amlogic: g12 CPU timers stop in suspend
arm64: dts: meson-g12b: support a311d and s922x cpu operating points
dt-bindings: arm: amlogic: add support for the Khadas VIM3
dt-bindings: arm: amlogic: add bindings for the Amlogic G12B based A311D SoC
dt-bindings: arm: amlogic: add bindings for G12B based S922X SoC
arm64: dts: meson: add video decoder entries
arm64: dts: meson-gx: add video decoder entry
dt-bindings: media: amlogic,vdec: add default compatible
arm64: dts: meson: add ethernet fifo sizes
arm64: dts: meson-g12b: add cpus OPP tables
arm64: dts: meson-g12a: enable DVFS on G12A boards
arm64: dts: meson-g12a: add cpus OPP table
arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux
arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi
...
Link: https://lore.kernel.org/r/7hr25fbi4v.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:13:03 +0000 (15:13 +0200)]
Merge tag 'amlogic-dt' of git://git./linux/kernel/git/khilman/linux-amlogic into arm/dt
ARM: dts: Amlogic updates for v5.4
Highlights
- odroid-c1: use MAC address from efuse
- add VDD_EE regulator to several boards
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: odroidc1: use the MAC address stored in the eFuse
ARM: dts: meson8b: mxq: add the VDDEE regulator
ARM: dts: meson8b: odroidc1: add the VDDEE regulator
ARM: dts: meson8b: ec100: add the VDDEE regulator
ARM: dts: meson8b: add the PWM_D output pin
ARM: dts: meson8b: add ethernet fifo sizes
Link: https://lore.kernel.org/r/7hzhk3bi96.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:10:33 +0000 (15:10 +0200)]
Merge tag 'socfpga_dts_updates_for_v5.4' of git://git./linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.4
- Add reset properties for various peripherals
- QSPI OCP and DMA on Arria10
- DMA on Agilex/Stratix10
- Update NAND controller bindings to match driver update
- Add NAND controller to Stratix10
- VINING FPGA board fixups
- Update button mapping
- Adjust GMAC1 clock and TXD skew settings
- Add missing reset-names for dma controller
* tag 'socfpga_dts_updates_for_v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: add missing reset-names for dma
ARM: dts: socfpga: Adjust GMAC1 clock and TXD lines skew on VINING FPGA
ARM: dts: socfpga: Fix up button mapping on VINING FPGA
arm64: dts: stratix10: Add NAND device node
ARM: dts: socfpga: update to new Denali NAND binding
arm64: dts: agilex/stratix10: Add reset properties for DMA
ARM: dts: socfpga: add reset properties for DMA
ARM: dts: socfpga: add the QSPI OCP reset property on arria10
Link: https://lore.kernel.org/r/20190819141659.26414-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 13:05:36 +0000 (15:05 +0200)]
Merge tag 'v5.4-rockchip-dts64-1' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
PWM-Fan and nor-flash for the RockPro64, a better display mode for
the Kevin Chromebook and a new board the Leez P710 SBC.
* tag 'v5.4-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC
arm64: dts: rockchip: enable internal SPI flash for RockPro64.
arm64: dts: rockchip: Add PWM fan for RockPro64
arm64: dts: rockchip: Specify override mode for kevin panel
Link: https://lore.kernel.org/r/20190819141659.26414-1-dinguyen@kernel.org
Link: https://lore.kernel.org/r/2362486.gYoCZEsBuK@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 12:44:28 +0000 (14:44 +0200)]
Merge tag 'v5.4-rockchip-dts32-1' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
A lot more love for Veyron devices with cleanups in the display and wifi
areas and also a 100ms speedup as a delay isn't needed anymore.
New boards are Tiger and Fievel from the Veyron family and the Mecer Xtreme
Mini S6, which I think is the first consumer-grade rk3229-based device in
the kernel.
* tag 'v5.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: add device tree for Mecer Xtreme Mini S6
Revert "ARM: dts: rockchip: add startup delay to rk3288-veyron panel-regulators"
ARM: dts: rockchip: Add pin names for rk3288-veyron fievel
ARM: dts: rockchip: A few fixes for veyron-{fievel,tiger}
ARM: dts: rockchip: Cleanup style around assignment operator
ARM: dts: rockchip: add veyron-tiger board
ARM: dts: rockchip: add veyron-fievel board
dt-bindings: ARM: dts: rockchip: Add bindings for rk3288-veyron-{fievel,tiger}
ARM: dts: rockchip: consolidate veyron panel and backlight settings
ARM: dts: rockchip: move rk3288-veryon display settings into a separate file
ARM: dts: rockchip: Limit WiFi TX power on rk3288-veyron-jerry
ARM: dts: rockchip: Specify rk3288-veyron-minnie's display timings
ARM: dts: rockchip: Specify rk3288-veyron-chromebook's display timings
Link: https://lore.kernel.org/r/1611583.rKl1eQBRh8@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 3 Sep 2019 12:40:55 +0000 (14:40 +0200)]
Merge tag 'samsung-dt-5.4' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.4
1. Add AHCI to Exynos5250,
2. Add camera and GPU power domains to Exynos5422,
3. Minor cleanup.
* tag 'samsung-dt-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add CAM power domain to Exynos5422/5800
ARM: dts: exynos: Add G3D power domain to Exynos542x
ARM: dts: exynos: Move MSC power domain to the right (sorted) place
ARM: dts: exynos: Add port map to Exynos5250 AHCI node
ARM: dts: exynos: Use space after '=' in exynos4412-itop-scp-core
Link: https://lore.kernel.org/r/20190816163042.6604-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Andrey Smirnov [Sat, 24 Aug 2019 00:27:03 +0000 (17:27 -0700)]
ARM: dts: vf610-zii-scu4-aib: Configure IRQ line for GPIO expander
Configure IRQ line for SX1503 GPIO expander. We already have
appropriate pinmux entry and all that is missing is "interrupt-parent"
and "interrupts" properties. Add them.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Thu, 22 Aug 2019 06:02:38 +0000 (08:02 +0200)]
ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards
Add support for i.MX6UL modules from Kontron Electronics GmbH (before
acquisition: Exceet Electronics) and evalkit boards based on it:
1. N6310 SOM: i.MX6 UL System-on-Module, a 25x25 mm solderable module
(LGA pads and pin castellations) with 256 MB RAM, 1 MB NOR-Flash,
256 MB NAND and other interfaces,
2. N6310 S: evalkit, w/wo eMMC, without display,
3. N6310 S 43: evalkit with 4.3" display,
The work is based on Exceet/Kontron source code (GPLv2) with numerous
changes:
1. Reorganize files,
2. Rename Exceet -> Kontron,
3. Rename models/compatibles to match newest Kontron product naming,
4. Fix coding style errors and adjust to device tree coding guidelines,
5. Fix DTC warnings,
6. Extend compatibles so eval boards inherit the SoM compatible,
7. Use defines instead of GPIO and interrupt flag values,
8. Use proper vendor compatible for Macronix SPI NOR,
9. Replace deprecated bindings with proper ones,
10. Sort nodes alphabetically,
11. Remove Admatec display nodes (not yet supported).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Thu, 22 Aug 2019 06:02:37 +0000 (08:02 +0200)]
dt-bindings: arm: fsl: Add Kontron i.MX6UL N6310 compatibles
Add the compatibles for Kontron i.MX6UL N6310 SoM and boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Thu, 22 Aug 2019 06:02:36 +0000 (08:02 +0200)]
dt-bindings: eeprom: at25: Add Anvo ANV32E61W
Document the compatible for ANV32E61W 64kb Serial SPI non-volatile SRAM.
Although it is a SRAM device, it can be accessed through EEPROM
interface. At least until there is no proper SRAM driver support for
it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Thu, 22 Aug 2019 06:02:35 +0000 (08:02 +0200)]
dt-bindings: vendor-prefixes: Add Anvo-Systems
Add vendor prefix for Anvo-Systems Dresden GmbH.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Baruch Siach [Wed, 21 Aug 2019 08:20:19 +0000 (11:20 +0300)]
dt-bindings: arm: fsl: add Hummingboard Pulse
Add binding documentation for the SolidRun Hummingboard Pulse board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Wed, 21 Aug 2019 01:39:36 +0000 (18:39 -0700)]
ARM: dts: vf610-zii-cfu1: Slow I2C0 down to 100 kHz
Fiber-optic modules attached to the bus are only rated to work at
100 kHz, so decrease the bus frequency to accommodate that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Mon, 19 Aug 2019 17:26:05 +0000 (19:26 +0200)]
dt-bindings: arm: imx: add imx8mq nitrogen support
The Nitrogen8M is an ARM based single board computer (SBC)
designed to leverage the full capabilities of NXP’s i.MX8M
Quad processor.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
[Dafna: porting vendor's code to mainline]
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Chuanhua Han [Thu, 1 Aug 2019 08:31:03 +0000 (16:31 +0800)]
dt-bindings: fsl: dspi: Add fsl,ls1088a-dspi compatible string
new compatible string: "fsl,ls1088a-dspi".
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexandre Belloni [Thu, 22 Aug 2019 21:35:03 +0000 (23:35 +0200)]
ARM: dts: pbab01: correct rtc vendor
The rtc8564 is made by Epson but is similar to the NXP pcf8563. Use the
correct vendor name.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mars Cheng [Mon, 19 Aug 2019 09:21:34 +0000 (17:21 +0800)]
dt-bindings: irq: mtk, sysirq: add support for mt6779
Add binding documentation of mediatek,sysirq for mt6779 SoC.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Mars Cheng [Mon, 19 Aug 2019 09:21:33 +0000 (17:21 +0800)]
dt-bindings: mtk-uart: add mt6779 uart bindings
Add documentation for mt6779 uart dt-bindings
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Mars Cheng [Mon, 19 Aug 2019 09:21:32 +0000 (17:21 +0800)]
dt-bindings: mediatek: add support for mt6779 reference board
Update binding document for mt6779 reference board
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Cao Van Dong [Thu, 11 Apr 2019 07:54:22 +0000 (16:54 +0900)]
dt-bindings: can: rcar_can: document r8a77470 support
Document SoC specific bindings for R-Car RZ/G1C(r8a77470) SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ulrich Hecht [Wed, 5 Dec 2018 01:17:05 +0000 (09:17 +0800)]
dt-bindings: can: rcar_canfd: document r8a77995 support
Adds compatible strings for the R-Car CAN FD controller in the D3 SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ulrich Hecht [Wed, 5 Dec 2018 01:17:04 +0000 (09:17 +0800)]
dt-bindings: can: rcar_can: document r8a77995 support
Adds compatible strings for the R-Car CAN controller in the D3 SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Marek Vasut [Sun, 18 Nov 2018 17:30:56 +0000 (18:30 +0100)]
dt-bindings: can: rcar_can: document r8a77990 support
Document the support for rcar_can on R8A77990 SoC devices.
Add R8A77990 to the list of SoCs which require the "assigned-clocks"
and "assigned-clock-rates" properties.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ondrej Jirman [Fri, 23 Aug 2019 09:42:28 +0000 (11:42 +0200)]
arm64: dts: allwinner: orange-pi-3: Enable WiFi
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).
WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.
You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:
https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:
brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Wed, 21 Aug 2019 14:38:35 +0000 (16:38 +0200)]
ARM: dts: sunxi: Add missing watchdog clocks
The watchdog has a clock on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Wed, 21 Aug 2019 14:38:34 +0000 (16:38 +0200)]
ARM: dts: sunxi: Add missing watchdog interrupts
The watchdog has an interrupt on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Ondrej Jirman [Tue, 20 Aug 2019 15:19:34 +0000 (17:19 +0200)]
arm64: dts: allwinner: h6: Add support for RTC and fix the clock tree
This patch adds RTC node and fixes the clock properties and nodes
to reflect the real clock tree.
The device nodes for the internal oscillator and osc32k are removed,
as these clocks are now provided by the RTC device. Clock references
are fixed accordingly, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Thu, 22 Aug 2019 08:21:15 +0000 (10:21 +0200)]
ARM: dts: sun7i: Add CSI0 controller
The CSI controller embedded in the A20 can be supported by our new driver.
Let's add it to our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Sunil Mohan Adapa [Wed, 21 Aug 2019 19:52:17 +0000 (12:52 -0700)]
arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.
eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s
Changes:
v3: Separate dts for eMMC variants
v2: Fix descriptions for VCC and VCCQ
Link: https://github.com/armbian/build/commit/174953de1eb09e6aa1ef7075066b573dba625398
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Sunil Mohan Adapa [Wed, 21 Aug 2019 19:52:16 +0000 (12:52 -0700)]
dt-bindings: arm: sunxi: Add compatible for A64 OlinuXino with eMMC
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
Add new compatible string to the bindings documentation for the A64 OlinuXino
board variant with on-board eMMC.
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Mon, 22 Jul 2019 08:12:29 +0000 (10:12 +0200)]
ARM: dts: v3s: Change the timers compatible
Unlike the A10 that has 6 timers available, the v3s has only three, with only
three interrupts. Let's change the compatible to reflect that, and add the
missing interrupts.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Mon, 22 Jul 2019 08:12:28 +0000 (10:12 +0200)]
ARM: dts: h3: Change the timers compatible
Unlike the A10 that has 6 timers available, the H3 has only two, with only
two interrupts, just like the A23. Let's change the compatible to reflect
that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Mon, 22 Jul 2019 08:12:27 +0000 (10:12 +0200)]
ARM: dts: a83t: Change the timers compatible
Unlike the A10 that has 6 timers available, the A83t has only two, with
only two interrupts, just like the A23. Let's change the compatible to
reflect that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Mon, 22 Jul 2019 08:12:26 +0000 (10:12 +0200)]
ARM: dts: a23/a33: Change the timers compatible
Unlike the A10 that has 6 timers available, the A23 and A33 has only two,
with only two interrupts. Let's change the compatible to reflect that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Mon, 22 Jul 2019 08:12:25 +0000 (10:12 +0200)]
ARM: dts: sun6i: Add missing timers interrupts
The timer unit in the A31 has 6 interrupts available. List all of them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Mon, 22 Jul 2019 08:12:24 +0000 (10:12 +0200)]
ARM: dts: sun5i: Add missing timers interrupts
The timer unit in the sun5i die has 6 interrupts available. List all of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Mon, 22 Jul 2019 08:12:23 +0000 (10:12 +0200)]
ARM: dts: sun4i: Add missing timers interrupts
The timer unit in the A10 has 6 interrupts available. List all of them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Maxime Ripard [Tue, 13 Aug 2019 12:47:40 +0000 (14:47 +0200)]
dt-bindings: mfd: Convert Allwinner GPADC bindings to a schema
The Allwinner SoCs have an embedded GPADC that is doing thermal reading as
well, supported in Linux, with a matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Jernej Skrabec [Fri, 16 Aug 2019 20:53:42 +0000 (22:53 +0200)]
arm64: dts: allwinner: h6: Introduce Tanix TX6 board
Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Jernej Skrabec [Fri, 16 Aug 2019 20:53:41 +0000 (22:53 +0200)]
dt-bindings: arm: sunxi: Add compatible for Tanix TX6 board
Add new Oranth Tanix TX6 board compatible string to the bindings
documentation.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Bhushan Shah [Fri, 16 Aug 2019 08:43:09 +0000 (14:13 +0530)]
arm64: allwinner: h6: add I2C nodes
Add device-tree nodes for i2c0 to i2c2, and also add relevant pinctrl
nodes.
Suggested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Bhushan Shah [Fri, 16 Aug 2019 08:43:08 +0000 (14:13 +0530)]
dt-bindings: i2c: mv64xxx: Add compatible for the H6 i2c node.
Allwinner H6 have a mv64xxx i2c interface available to be used.
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Chen-Yu Tsai [Wed, 14 Aug 2019 04:22:08 +0000 (12:22 +0800)]
ARM: dts: sunxi: Add mdio bus sub-node to GMAC
The DWMAC binding never supported having the Ethernet PHY node as a
direct child to the controller, nor did it support the "phy" property
as a way to specify which Ethernet PHY to use. What seemed to work
was simply the implementation ignoring the "phy" property and instead
probing all addresses on the MDIO bus and using the first available
one.
The recent switch from "phy" to "phy-handle" breaks the assumptions
of the implementation, and does not match what the binding requires.
The binding requires that if an MDIO bus is described, it shall be
a sub-node with the "snps,dwmac-mdio" compatible string.
Add a device node for the MDIO bus, and move the Ethernet PHY node
under it. Also fix up the #address-cells and #size-cells properties
where needed.
Fixes:
de332de26d19 ("ARM: dts: sunxi: Switch from phy to phy-handle")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Clément Péron [Mon, 12 Aug 2019 10:23:55 +0000 (12:23 +0200)]
arm64: dts: allwinner: Enable DDC regulator for Beelink GS1
Beelink GS1 has a DDC I2C bus voltage shifter. This is actually missing
and video is limited to 1024x768 due to missing EDID information.
Add the DDC regulator in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Clément Péron [Mon, 12 Aug 2019 10:51:15 +0000 (12:51 +0200)]
arm64: dts: allwinner: h6: Enable SPDIF for Beelink GS1
Beelink GS1 board has a SPDIF out connector, so enable it in
the device-tree and add a simple SPDIF soundcard.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Clément Péron [Mon, 12 Aug 2019 10:51:14 +0000 (12:51 +0200)]
arm64: dts: allwinner: Add SPDIF node for Allwinner H6
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).
Only one pinmuxing is available so set it as default.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Icenowy Zheng [Sun, 28 Jul 2019 03:12:27 +0000 (11:12 +0800)]
ARM: dts: sun8i: s3: add devicetree for Lichee zero plus w/ S3
Lichee zero plus is a core board made by Sipeed, which includes on-board
TF slot or SMT SD NAND, and optional SPI NOR or eMMC, a UART debug
header, a microUSB slot and a gold finger connector for expansion. It
can use either Sochip S3 or Allwinner S3L SoC.
Add the basic device tree for the core board, w/o optional onboard
storage, and with S3 SoC.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Icenowy Zheng [Sun, 28 Jul 2019 03:12:25 +0000 (11:12 +0800)]
ARM: sunxi: dts: s3/s3l/v3: add DTSI files for S3/S3L/V3 SoCs
The Allwinner S3/S3L/V3 SoCs all share the same die with the V3s SoC,
but with more GPIO wired out of the package.
Add a DTSI file for these SoCs. It just replaces some compatible strings
of the V3s DTSI now. As these SoCs share the same feature set on Linux,
we use the first known chip (V3) as the file's name.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Icenowy Zheng [Sun, 28 Jul 2019 03:12:26 +0000 (11:12 +0800)]
dt-bindings: arm: sunxi: add binding for Lichee Zero Plus core board
The Lichee Zero Plus is a core board made by Sipeed, with a microUSB
connector on it, TF slot or WSON8 SD chip, optional eMMC or SPI Flash.
It has a gold finger connector for expansion, and UART is available from
reserved pins w/ 2.54mm pitch. The board can use either SoChip S3 or
Allwinner V3L SoCs.
Add the device tree binding of the basic version of the core board --
w/o eMMC or SPI Flash, w/ TF slot or WSON8 SD, and use S3 SoC.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Ondrej Jirman [Tue, 6 Aug 2019 15:57:43 +0000 (17:57 +0200)]
arm64: dts: allwinner: orange-pi-3: Enable HDMI output
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high.
This is realized by the ddc-en-gpios property.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Chen-Yu Tsai [Sun, 28 Jul 2019 14:59:44 +0000 (22:59 +0800)]
ARM: dts: sun8i: a83t: Enable HDMI output on Cubietruck Plus
The Cubietruck Plus has an HDMI connector tied to the HDMI output of the
SoC.
Enables display output via HDMI on the Cubietruck Plus. The connector
device node is named "hdmi-connector" as there is also a display port
connector, which is tied to the MIPI DSI output of the SoC through a
MIPI-DSI-to-DP bridge. This part is not supported yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Qii Wang [Thu, 22 Aug 2019 12:35:16 +0000 (20:35 +0800)]
arm64: dts: mt8183: add I2C nodes
Add i2c nodes to mt8183 and mt8183-evb.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Hsin-Hsiung Wang [Thu, 22 Aug 2019 08:55:40 +0000 (16:55 +0800)]
arm64: dts: mt8183: fix pwrap gic number
The correct gic number of pwrap is 185 instead of 209. This patch fixes
it to avoid triggering error interrupt.
Fixes:
e526c9bc11f8 ("arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile")
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Ryder Lee [Thu, 11 Jul 2019 02:14:23 +0000 (10:14 +0800)]
arm: dts: mediatek: add basic support for MT7629 SoC
This adds basic support for MT7629 reference board.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Joel Stanley [Wed, 21 Aug 2019 04:56:55 +0000 (14:26 +0930)]
ARM: dts: aspeed: swift: Add eMMC device
Swift contains an eMMC device attached to the second SDHCI controller.
Reviewed-by: Adriana Kobylak <anoo@us.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Jacopo Mondi [Sat, 6 Jul 2019 14:07:30 +0000 (16:07 +0200)]
arm64: dts: renesas: Update 'vsps' properties for readability
Update the 'vsps' property in the R-Car Gen3 SoC device tree files to
match what's in the documentation example.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Kuninori Morimoto [Wed, 27 Feb 2019 05:02:54 +0000 (14:02 +0900)]
arm64: dts: renesas: r8a77965-salvator-x(s): Enable HDMI sound
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> # Salvator-XS
[geert: Preserve sort order]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Wed, 21 Aug 2019 09:52:19 +0000 (11:52 +0200)]
arm64: dts: renesas: r8a774c0: Fix register range of display node
Since the R8A774C0 SoC uses DU{0,1} only, the register block length
should be 0x40000.
Based on commit
06585ed38b6698bc ("arm64: dts: renesas: r8a77990: Fix
register range of display node") for R-Car E3.
Fixes:
8ed3a6b223159df3 ("arm64: dts: renesas: r8a774c0: Add display output support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Yoshihiro Kaneko [Mon, 19 Aug 2019 12:56:33 +0000 (21:56 +0900)]
arm64: dts: renesas: r8a77970: Sort nodes
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Yoshihiro Kaneko [Mon, 19 Aug 2019 12:56:18 +0000 (21:56 +0900)]
arm64: dts: renesas: r8a7796: Sort nodes
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Yoshihiro Kaneko [Mon, 19 Aug 2019 12:56:01 +0000 (21:56 +0900)]
arm64: dts: renesas: r8a774c0: Sort nodes
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Yoshihiro Kaneko [Mon, 19 Aug 2019 12:55:41 +0000 (21:55 +0900)]
arm64: dts: renesas: r8a774c0: cat874: Sort nodes
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Yoshihiro Kaneko [Mon, 19 Aug 2019 12:54:55 +0000 (21:54 +0900)]
arm64: dts: renesas: r8a774a1: Sort nodes
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Mon, 7 May 2018 09:16:48 +0000 (11:16 +0200)]
ARM: dts: r8a77470: Add PMU device node
Enable support for the ARM Performance Monitor Units in the Cortex-A7
CPU cores on RZ/G1C by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Andrew Jeffery [Fri, 12 Jul 2019 03:37:26 +0000 (13:07 +0930)]
ARM: dts: aspeed: Enable first MMC slot on AST2500 EVB
The EVB contains two slots. Enable one of them for testing purposes.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Andrew Jeffery [Fri, 12 Jul 2019 03:37:25 +0000 (13:07 +0930)]
ARM: dts: aspeed: Describe SD controllers
The AST2400 and AST2500 both share the same SD controller, at the same
location in the physical address space and the same hardware interrupt,
with the same clock configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Neil Armstrong [Tue, 20 Aug 2019 14:40:52 +0000 (16:40 +0200)]
arm64: dts: add support for SM1 based SEI Robotics SEI610
Add support for the Amlogic SM1 Based SEI610 board.
The SM1 SoC is a derivative of the G12A SoC Family with :
- Cortex-A55 core instead of A53
- more power domains, including USB & PCIe
- a neural network co-processor (NNA)
- a CSI input and image processor
- some changes in the audio complex, thus not yet enabled
The SEI610 board is a derivative of the SEI510 board with :
- removed ADC based touch button, replaced with 3x GPIO buttons
- physical switch disabling on-board MICs
- USB-C port for USB 2.0 OTG
- On-board FTDI USB2SERIAL port for Linux console
Audio, Display and USB support will be added later when support of the
corresponding power domains will be added, for now they are kept disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: fix minor typo regultor -> regulator]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Neil Armstrong [Tue, 20 Aug 2019 14:40:51 +0000 (16:40 +0200)]
dt-bindings: arm: amlogic: add SEI Robotics SEI610 bindings
Add the compatible for the Amlogic SM1 Based SEI610 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Neil Armstrong [Tue, 20 Aug 2019 14:40:50 +0000 (16:40 +0200)]
dt-bindings: arm: amlogic: add SM1 bindings
Add bindings for the new Amlogic SM1 SoC Family.
It a derivative of the G12A SoC Family with :
- Cortex-A55 core instead of A53
- more power domains
- a neural network co-processor
- a CSI input and image processor
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Daniel Baluta [Wed, 7 Aug 2019 16:42:57 +0000 (19:42 +0300)]
arm64: dts: imx8qxp: Add DSP DT node
This includes DSP reserved memory, ADMA DSP device and DSP MU
communication channels description.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Sun, 18 Aug 2019 06:32:25 +0000 (02:32 -0400)]
arm64: dts: imx8mn: Add cpu-freq support
Add A53 OPP table, cpu regulator and speed grading node to
support cpu-freq driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Sun, 18 Aug 2019 06:32:20 +0000 (02:32 -0400)]
arm64: dts: imx8mn-ddr4-evk: Add rohm,
bd71847 PMIC support
On i.MX8MN DDR4 EVK board, there is a rohm,
bd71847 PMIC
on i2c1 bus, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Sun, 18 Aug 2019 06:32:19 +0000 (02:32 -0400)]
arm64: dts: imx8mn-ddr4-evk: Add i2c1 support
Enable i2c1 on i.MX8MN DDR4 EVK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Wed, 19 Jun 2019 02:21:44 +0000 (10:21 +0800)]
arm64: dts: freescale: Add i.MX8MN DDR4 EVK board support
This patch adds basic i.MM8MN DDR4 EVK board support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Thu, 15 Aug 2019 02:57:30 +0000 (22:57 -0400)]
arm64: dts: imx8mn: Add gpio-ranges property
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MN pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Wed, 19 Jun 2019 02:21:43 +0000 (10:21 +0800)]
arm64: dts: freescale: Add i.MX8MN dtsi support
The i.MX8M Nano Media Applications Processor is a new SoC of the i.MX8M
family, it is a 14nm FinFET product of the growing mScale family targeting
the consumer market. It is built in Samsung 14LPP to achieve both high
performance and low power consumption and relies on a powerful fully
coherent core complex based on a quad core ARM Cortex-A53 cluster,
Cortex-M7 low-power coprocessor and graphics accelerator.
This patch adds the basic dtsi support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Geert Uytterhoeven [Wed, 31 Jul 2019 11:27:39 +0000 (13:27 +0200)]
arm64: dts: renesas: r8a77980: Fix IPMMU-VC0 base address
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the base address of the IPMMU-VC0 block on R-Car V3H is
0xfe990000.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Simon Horman [Mon, 29 Jul 2019 08:03:56 +0000 (10:03 +0200)]
arm64: dts: renesas: ebisu, draak: Limit EtherAVB to 100Mbps
* According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode isn't supported
on R-Car E3 (r8a77990) and D3 (r8a77995).
* TX clock internal delay mode is required for reliable 1Gbps communication
using the KSZ9031RNX phy present on the Ebisu and Draak boards.
Thus, the E3 based Ebisu and D3 based Draak boards can not reliably
use 1Gbps and the speed should be limited to 100Mbps.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fabrizio Castro [Mon, 15 Jul 2019 09:32:49 +0000 (10:32 +0100)]
arm64: dts: renesas: hihope-common: Add HDMI audio support
This patch adds support for HDMI audio to the device tree
common to the HiHope RZ/G2M and the HiHope RZ/G2N.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Fri, 16 Aug 2019 08:22:29 +0000 (10:22 +0200)]
ARM: dts: r8a7779: Use SYSC "always-on" PM Domain for HSCIF
Hook up HSCIF serial devices that are part of the CPG/MSTP Clock Domain
to the SYSC "always-on" PM Domain, for a more consistent
device-power-area description in DT.
Cfr. commit
751e29bbb64ad091 ("ARM: dts: r8a7779: Use SYSC "always-on"
PM Domain").
Fixes:
055d15a88f66b096 ("ARM: dts: r8a7779: Add HSCIF0/1 device nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Andrey Smirnov [Wed, 14 Aug 2019 19:35:36 +0000 (12:35 -0700)]
ARM: vf610-zii-cfu1: Add node for switch watchdog
Add I2C child node for switch watchdog present on CFU1.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Cory Tusar <cory.tusar@zii.aero>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Felsch [Wed, 14 Aug 2019 07:55:58 +0000 (09:55 +0200)]
ARM: dts: imx6: drop gpmi-nand address and size cells
Since commit
fe2585e9c29a ("doc: dt: mtd: support partitions in a
special 'partitions' subnode") and commit
5cfdedb7b9a0 ("mtd: ofpart:
move ofpart partitions to a dedicated dt node") the partitioning should
be within a partitions sub-node.
Baseboard device trees following that scheme will get a dtc warning due
to the predefined #address-cells and #size-cells properties:
arch/arm/boot/dts/imx6qdl.dtsi:171.26-189.5: Warning (avoid_unnecessary_addr_size): /soc/gpmi-nand@112000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
I found no upstream imx6 baseboard using the old partitioning scheme, so
we can drop the two properties to avoid such warnings.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Felsch [Wed, 14 Aug 2019 07:55:57 +0000 (09:55 +0200)]
ARM: dts: imx6: replace simple-bus by simple-mfd for anatop
Replace it to fix the following DTC warnings:
arch/arm/boot/dts/imx6qdl.dtsi:702.19-715.7: Warning (simple_bus_reg): /soc/aips-bus@
2000000/anatop@
20c8000/regulator-1p1: missing or empty reg/ranges property
arch/arm/boot/dts/imx6qdl.dtsi:717.19-730.7: Warning (simple_bus_reg): /soc/aips-bus@
2000000/anatop@
20c8000/regulator-3p0: missing or empty reg/ranges property
arch/arm/boot/dts/imx6qdl.dtsi:732.19-745.7: Warning (simple_bus_reg): /soc/aips-bus@
2000000/anatop@
20c8000/regulator-2p5: missing or empty reg/ranges property
arch/arm/boot/dts/imx6qdl.dtsi:747.32-762.7: Warning (simple_bus_reg): /soc/aips-bus@
2000000/anatop@
20c8000/regulator-vddcore: missing or empty reg/ranges property
arch/arm/boot/dts/imx6qdl.dtsi:764.29-779.7: Warning (simple_bus_reg): /soc/aips-bus@
2000000/anatop@
20c8000/regulator-vddpu: missing or empty reg/ranges property
arch/arm/boot/dts/imx6qdl.dtsi:781.31-796.7: Warning (simple_bus_reg): /soc/aips-bus@
2000000/anatop@
20c8000/regulator-vddsoc: missing or empty reg/ranges property
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Philippe Schenker [Mon, 12 Aug 2019 14:21:28 +0000 (14:21 +0000)]
ARM: dts: imx6qdl-colibri: add phy to fec
Add the phy-node and mdio bus to the fec-node, represented as is on
hardware.
This commit includes micrel,led-mode that is set to the default
value, prepared for someone who wants to change this.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksandr Suvorov [Mon, 12 Aug 2019 14:21:21 +0000 (14:21 +0000)]
ARM: dts: imx7-colibri: add recovery for I2C for iMX7
- add recovery mode for applicable i2c buses for
Colibri iMX7 module.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Philippe Schenker [Mon, 12 Aug 2019 14:21:19 +0000 (14:21 +0000)]
ARM: dts: imx7-colibri: Add sleep pinctrl to ethernet
Add sleep pinmux to the fec so it can properly sleep.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Philippe Schenker [Mon, 12 Aug 2019 14:21:18 +0000 (14:21 +0000)]
ARM: dts: imx7-colibri: prepare module device tree for FlexCAN
Prepare FlexCAN use on SODIMM 55/63 178/188. Those SODIMM pins are
compatible for CAN bus use with several modules from the Colibri
family.
Add Better drivestrength and also add flexcan2.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Mon, 12 Aug 2019 14:21:17 +0000 (14:21 +0000)]
ARM: dts: imx7-colibri: disable HS400
Force HS200 by masking bit 63 of the SDHCI capability register.
The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With
that the stack checks bit 63 to descide whether HS400 is available.
Using sdhci-caps-mask allows to mask bit 63. The stack then selects
HS200 as operating mode.
This prevents rare communication errors with minimal effect on
performance:
sdhci-esdhc-imx
30b60000.usdhc: warning! HS400 strobe DLL
status REF not lock!
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marcel Ziswiler [Mon, 12 Aug 2019 14:21:15 +0000 (14:21 +0000)]
ARM: dts: imx7-colibri: make sure module supplies are always on
Prevent regulators from being switched off.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
projects / linux-2.6-microblaze.git / log