ALSA: hda/tegra: Update scratch reg. communication

Tegra234 chip scratch register communication between audio
and hdmi driver differs slightly in the way it triggers the
interrupt compared to legacy chips. Interrupt is triggered
by writing non-zero values to verb 0xF80 instead of 31st bit
of scratch register.

DP MST support changed the NID to be used for scratch register
read/write from audio function group NID to Converter widget NID.

Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20220216092240.26464-4-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda/tegra: Hardcode GCAP ISS value on T234

The GCAP register on Tegra234 implies no Input Streams(ISS)
supported, but the HW output stream descriptor programming
should start with offset 0x20*4 from base stream descriptor
address. This will be a problem while calculating the offset
for output stream descriptor which will be considering input
stream also. So here output stream starts with offset 0 which
is wrong as HW register for output stream offset starts with 4.
So hardcode the input stream numbers to 4 to avoid the issue
in offset calculation.

Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20220216092240.26464-3-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda/tegra: Add Tegra234 hda driver support

Add hda driver support for the Tegra234 chip. The hdacodec
on this chip now supports DP MST feature, HDA block contains
azalia controller and one hda-codec instance by supporting
4 independent output streams over DP MST mode. There is no
input stream support.

Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20220216092240.26464-2-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: Expose codec cleanup and power-save functions

With few changes, snd_hda_codec_set_power_save() and
snd_hda_codec_cleanup_for_unbind() can be re-used by ASoC drivers.
While at it, provide kernel doc for the exposed functions.

Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220214101404.4074026-5-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: Update and expose codec register procedures

With few changes, snd_hda_codec_register() and its
unregister-counterpart can be re-used by ASoC drivers. While at it,
provide kernel doc for the exposed functions.

Due to ALSA-device vs ASoC-component organization differences, new
'snddev_managed' argument is specified allowing for better control over
codec registration process.

Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220214101404.4074026-4-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: Update and expose snd_hda_codec_device_init()

With few changes, snd_hda_codec_device_init() can be re-used by ASoC
drivers. While at it, provide kernel doc for the exposed function.

Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220214101404.4074026-3-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: Add snd_hdac_ext_bus_link_at() helper

This patch exposes a new helper to directly retrieve the link from the
codec address, and makes use of this helper when retrieving the link
from the codec name.

Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220214101404.4074026-2-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda/hdmi: add keep-alive support for ADL-P and DG2

Implement HDA keep alive (KAE) support for Intel display codecs. When no
audio stream is active, the display codec will provide a continuous clock
and a valid but silent audio stream to any connected HDMI/DP receiver.
Without this, upon starting a new playback stream, initial samples may be
lost as many receivers require time to initialize for new clock.

This is a new feature in Intel AlderLake-P display codec implementation
and replaces the Intel i915 silent-stream extension that has been used
on older hardware. Main benefit of the new method is that codec no longer
needs to be kept in D0 power state.

This patch depends on commit 112a87c48e83 ("drm/i915/display: program
audio CDCLK-TS for keepalives").

[ a minor coding-style fix by tiwai ]

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Jyri Sarha <jyri.sarha@intel.com>
Link: https://lore.kernel.org/r/20220216172405.3994959-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge branch 'for-linus' into for-next

Merge tag 'platform-drivers-x86-serial-multi-instantiate-1' of git://git./linux/kernel/git/pdx86/platform-drivers-x86 into for-next

This branch contains 5.17-rc1 + the SPI tree's spi-acpi-helpers tag +
the other patches from the "[PATCH v6 0/9] Support Spi in
i2c-multi-instantiate driver" series.

Merge tag 'asoc-fix-v5.17-rc4' of https://git./linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v5.18

More fixes that have arrived in the past few -rcs, plus a MAINTAINERS
update.  The biggest update here is the fix for control change
notifications in ASoC generic controls found by mixer-test.

ALSA: hda/realtek: Fix deadlock by COEF mutex

The recently introduced coef_mutex for Realtek codec seems causing a
deadlock when the relevant code is invoked from the power-off state;
then the HD-audio core tries to power-up internally, and this kicks
off the codec runtime PM code that tries to take the same coef_mutex.

In order to avoid the deadlock, do the temporary power up/down around
the coef_mutex acquisition and release.  This assures that the
power-up sequence runs before the mutex, hence no re-entrance will
happen.

Fixes: b837a9f5ab3b ("ALSA: hda: realtek: Fix race at concurrent COEF updates")
Reported-and-tested-by: Julian Wollrath <jwollrath@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220214132838.4db10fca@schienar
Link: https://lore.kernel.org/r/20220214130410.21230-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: usb-audio: Don't abort resume upon errors

The default mixer resume code treats the errors at restoring the
modified mixer items as a fatal error, and it returns back to the
caller.  This ends up in the resume failure, and the device will be
come unavailable, although basically those errors are intermittent and
can be safely ignored.

The problem itself has been present from the beginning, but it didn't
hit usually because the code tries to resume only the modified items.
But now with the recent commit to forcibly initialize each item at the
probe time, the problem surfaced more often, hence it appears as a
regression.

This patch fixes the regression simply by ignoring the errors at
resume.

Fixes: b96681bd5827 ("ALSA: usb-audio: Initialize every feature unit once at probe time")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215561
Link: https://lore.kernel.org/r/20220214125711.20531-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: Fix missing codec probe on Shenker Dock 15

By some unknown reason, BIOS on Shenker Dock 15 doesn't set up the
codec mask properly for the onboard audio.  Let's set the forced codec
mask to enable the codec discovery.

Reported-by: dmummenschanz@web.de
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/trinity-f018660b-95c9-442b-a2a8-c92a56eb07ed-1644345967148@3c-app-webde-bap22
Link: https://lore.kernel.org/r/20220214100020.8870-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: Fix regression on forced probe mask option

The forced probe mask via probe_mask 0x100 bit doesn't work any longer
as expected since the bus init code was moved and it's clearing the
codec_mask value that was set beforehand.  This patch fixes the
long-time regression by moving the check_probe_mask() call.

Fixes: a41d122449be ("ALSA: hda - Embed bus into controller object")
Reported-by: dmummenschanz@web.de
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/trinity-f018660b-95c9-442b-a2a8-c92a56eb07ed-1644345967148@3c-app-webde-bap22
Link: https://lore.kernel.org/r/20220214100020.8870-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda/realtek: Add quirk for Legion Y9000X 2019

Legion Y9000X 2019 has the same speaker with Y9000X 2020,
but with a different quirk address. Add one quirk entry
to make the speaker work on Y9000X 2019 too.

Signed-off-by: Yu Huang <diwang90@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220212160835.165065-1-diwang90@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: usb-audio: revert to IMPLICIT_FB_FIXED_DEV for M-Audio FastTrack Ultra

Commit 83b7dcbc51c930fc2079ab6c6fc9d719768321f1 introduced a generic
implicit feedback parser, which fails to execute for M-Audio FastTrack
Ultra sound cards. The issue is with the ENDPOINT_SYNCTYPE check in
add_generic_implicit_fb() where the SYNCTYPE is ADAPTIVE instead of ASYNC.
The reason is that the sync type of the FastTrack output endpoints are
set to adaptive in the quirks table since commit
65f04443c96dbda11b8fff21d6390e082846aa3c.

Fixes: 83b7dcbc51c9 ("ALSA: usb-audio: Add generic implicit fb parsing")
Signed-off-by: Matteo Martelli <matteomartelli3@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220211224913.20683-2-matteomartelli3@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: cleanup double word in comment

Remove the second 'device'.

Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220209150133.2291856-1-trix@redhat.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: Add PCI and HDMI IDs for Intel Raptor Lake

Add a set of HD Audio PCI IDs, and the HDMI codec VID, for
Intel Raptor Lake.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220210185423.3671603-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ASoC: wm_adsp: Correct control read size when parsing compressed buffer

When parsing the compressed stream the whole buffer descriptor is
now read in a single cs_dsp_coeff_read_ctrl; on older firmwares
this descriptor is just 4 bytes but on more modern firmwares it is
24 bytes. The current code reads the full 24 bytes regardless, this
was working but reading junk for the last 20 bytes. However commit
f444da38ac92 ("firmware: cs_dsp: Add offset to cs_dsp read/write")
added a size check into cs_dsp_coeff_read_ctrl, causing the older
firmwares to now return an error.

Update the code to only read the amount of data appropriate for
the firmware loaded.

Fixes: 04ae08596737 ("ASoC: wm_adsp: Switch to using wm_coeff_read_ctrl for compressed buffers")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220210172053.22782-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: qcom: Actually clear DMA interrupt register for HDMI

In commit da0363f7bfd3 ("ASoC: qcom: Fix for DMA interrupt clear reg
overwriting") we changed regmap_write() to regmap_update_bits() so that
we can avoid overwriting bits that we didn't intend to modify.
Unfortunately this change breaks the case where a register is writable
but not readable, which is exactly how the HDMI irq clear register is
designed (grep around LPASS_HDMITX_APP_IRQCLEAR_REG to see how it's
write only). That's because regmap_update_bits() tries to read the
register from the hardware and if it isn't readable it looks in the
regmap cache to see what was written there last time to compare against
what we want to write there. Eventually, we're unable to modify this
register at all because the bits that we're trying to set are already
set in the cache.

This is doubly bad for the irq clear register because you have to write
the bit to clear an interrupt. Given the irq is level triggered, we see
an interrupt storm upon plugging in an HDMI cable and starting audio
playback. The irq storm is so great that performance degrades
significantly, leading to CPU soft lockups.

Fix it by using regmap_write_bits() so that we really do write the bits
in the clear register that we want to. This brings the number of irqs
handled by lpass_dma_interrupt_handler() down from ~150k/sec to ~10/sec.

Fixes: da0363f7bfd3 ("ASoC: qcom: Fix for DMA interrupt clear reg overwriting")
Cc: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20220209232520.4017634-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ALSA: ca0106: Rename register macro names

ca0106 driver code uses too generic names for its register definitions
such as PTR, DATA, IPR, etc, which may eventually conflict with other
code.  This patch renames (some of) those register definitions with
CA0106_ prefix to avoid the conflicts.

Link: https://lore.kernel.org/r/20220210124227.11272-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: memalloc: invalidate SG pages before sync

It seems that calling invalidate_kernel_vmap_range() is more correct
to be called before dma_sync_*(), judging from the other thread:
  https://lore.kernel.org/all/20220111085958.GA22795@lst.de/
Although this won't matter much in practice, let's fix the call order
for consistency.

Fixes: a25684a95646 ("ALSA: memalloc: Support for non-contiguous page allocation")
Reported-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220210123344.8756-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: memalloc: Fix dma_need_sync() checks

dma_need_sync() checks each DMA address.  Fix the incorrect usages
for non-contiguous and non-coherent page allocations.
Fortunately, there are no actual call sites that need manual syncs
yet.

Fixes: a25684a95646 ("ALSA: memalloc: Support for non-contiguous page allocation")
Fixes: 73325f60e2ed ("ALSA: memalloc: Support for non-coherent page allocation")
Cc: <stable@vger.kernel.org>
Reported-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Link: https://lore.kernel.org/r/20220210123344.8756-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

MAINTAINERS: update cros_ec_codec maintainers

Updates cros_ec_codec maintainers.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Acked-By: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-By: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20220208031242.227563-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ALSA: hda: Fix driver index handling at re-binding

HD-audio driver handles the multiple instances and keeps the static
index that is incremented at each probe.  This becomes a problem when
user tries to re-bind the device via sysfs multiple times; as the
device index isn't cleared unlike rmmod case, it points to the next
element at re-binding, and eventually later you can't probe any more
when it reaches to SNDRV_CARDS_MAX (usually 32).

This patch is an attempt to improve the handling at rebinding.
Instead of a static device index, now we keep a bitmap and assigns to
the first zero bit position.  At the driver remove, in return, the
bitmap slot is cleared again, so that it'll be available for the next
probe.

Reported-by: Alexander Sergeyev <sergeev917@gmail.com>
Link: https://lore.kernel.org/r/20220209081912.20687-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ASoC: rt5682: do not block workqueue if card is unbound

The current rt5682_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.

This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove  or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.

Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220207153000.3452802-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5668: do not block workqueue if card is unbound

The current rt5668_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.

This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove  or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.

Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220207153000.3452802-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5682s: do not block workqueue if card is unbound

The current rt5682s_jack_detect_handler() assumes the component
and card will always show up and implements an infinite usleep
loop waiting for them to show up.

This does not hold true if a codec interrupt (or other
event) occurs when the card is unbound. The codec driver's
remove  or shutdown functions cannot cancel the workqueue due
to the wait loop. As a result, code can either end up blocking
the workqueue, or hit a kernel oops when the card is freed.

Fix the issue by rescheduling the jack detect handler in
case the card is not ready. In case card never shows up,
the shutdown/remove/suspend calls can now cancel the detect
task.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220207153000.3452802-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: tas2770: Insert post reset delay

Per TAS2770 datasheet there must be a 1 ms delay from reset to first
command. So insert delays into the driver where appropriate.

Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220204095301.5554-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Revert "ASoC: mediatek: Check for error clk pointer"

This reverts commit 9de2b9286a6d ("ASoC: mediatek: Check for error clk
pointer").

With this patch in the tree, Chromebooks running the affected hardware
no longer boot. Bisect points to this patch, and reverting it fixes
the problem.

An analysis of the code with this patch applied shows:

        ret = init_clks(pdev, clk);
        if (ret)
                return ERR_PTR(ret);
...
                for (j = 0; j < MAX_CLKS && data->clk_id[j]; j++) {
                        struct clk *c = clk[data->clk_id[j]];

                        if (IS_ERR(c)) {
                                dev_err(&pdev->dev, "%s: clk unavailable\n",
                                        data->name);
                                return ERR_CAST(c);
                        }

                        scpd->clk[j] = c;
                }

Not all clocks in the clk_names array have to be present. Only the clocks
in the data->clk_id array are actually needed. The code already checks if
the required clocks are available and bails out if not. The assumption that
all clocks have to be present is wrong, and commit 9de2b9286a6d ("ASoC:
mediatek: Check for error clk pointer") needs to be reverted.

Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Cc: Mark Brown <broonie@kernel.org>
Cc: James Liao <jamesjj.liao@mediatek.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Reported-by: Daniel Golle <daniel@makrotopia.org>
Fixes: 9de2b9286a6d ("ASoC: mediatek: Check for error clk pointer")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220207160923.3911501-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>

kselftest: alsa: fix spelling mistake "desciptor" -> "descriptor"

There are some spelling mistakes in some ksft messages. Fix them.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220207092235.240284-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: usb-audio: remove redundant assignment to variable c

The variable c is being initialized in an outer for-loop and also
re-initialized inside an inner for-loop. The first initialization
is redundant and can be removed.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220207140617.341172-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

kselftest: alsa: Declare most functions static

This program has only one file so most functions can be static.

Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220202150902.19563-2-broonie@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>

kselftest: alsa: Check for event generation when we write to controls

Add some coverage of event generation to mixer-test. Rather than doing a
separate set of writes designed to trigger events we add a step to the
existing write_and_verify() which checks to see if the value we read back
from non-volatile controls matches the value before writing and that an
event is or isn't generated as appropriate. The "tests" for events then
simply check that no spurious or missing events were detected. This avoids
needing further logic to generate appropriate values for each control type
and maximises coverage.

When checking for events we use a timeout of 0. This relies on the kernel
generating any event prior to returning to userspace when setting a control.
That is currently the case and it is difficult to see it changing, if it
does the test will need to be updated. Using a delay of 0 means that we
don't slow things down unduly when checking for no event or when events
fail to be generated.

We don't check behaviour for volatile controls since we can't tell what
the behaviour is supposed to be for any given control.

Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220202150902.19563-1-broonie@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ASoC: ops: Fix stereo change notifications

Merge series from Mark Brown <broonie@kernel.org>:

The event generation coverage I just wrote shows that the generic ASoC
ops fail to generate events for stereo controls when only the first
channel is changed, we just return the status for the second channel and
discard that for the first.

ACPI / scan: Create platform device for CS35L41

The ACPI device with CSC3551 or CLSA0100 are sound cards
with multiple instances of CS35L41 connected by I2C or SPI
to the main CPU.

We add an ID to the ignore_serial_bus_ids list to enumerate
all I2C or SPI devices correctly.

The same IDs are also added into serial-multi-instantiate
so that the driver can correctly enumerate the ACPI.

Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220121172431.6876-10-sbinding@opensource.cirrus.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ALSA: hda/realtek: Add support for HP Laptops

Add support for two and four CS35L41 using the component
binding method

Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220121172431.6876-9-sbinding@opensource.cirrus.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: serial-multi-instantiate: Add SPI support

Add support for spi bus in serial-multi-instantiate driver

Some peripherals can have either a I2C or a SPI connection
to the host (but not both) but use the same HID for both
types. So it is not possible to use the HID to determine
whether it is I2C or SPI. The driver must check the node
to see if it contains I2cSerialBus or SpiSerialBus entries.

For backwards-compatibility with the existing nodes I2C is
checked first and if such entries are found ONLY I2C devices
are created. Since some existing nodes that were already
handled by this driver could also contain unrelated
SpiSerialBus nodes that were previously ignored, and this
preserves that behavior. If there is ever a need to handle
a node where both I2C and SPI devices must be instantiated
this can be added in future.

Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220121172431.6876-8-sbinding@opensource.cirrus.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: serial-multi-instantiate: Reorganize I2C functions

Reorganize I2C functions to accommodate SPI support
Split the probe and factor out parts of the code
that will be used in the SPI support
Also switched from strlcpy() to strscpy()

Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220121172431.6876-7-sbinding@opensource.cirrus.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: i2c-multi-instantiate: Rename it for a generic serial driver name

Rename I2C multi instantiate driver to serial-multi-instantiate for
upcoming addition of SPI support

Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220121172431.6876-6-sbinding@opensource.cirrus.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

ASoC: amd: acp: Set gpio_spkr_en to None for max speaker amplifer in machine driver

Maxim codec driver already enabling/disabling spk_en_gpio in form of sd_mode gpio
hence remove such gpio access control from machine driver to avoid conflict

Signed-off-by: V sujith kumar Reddy <vsujithkumar.reddy@amd.com>
Link: https://lore.kernel.org/r/20220131203225.1418648-1-vsujithkumar.reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ops: Fix stereo change notifications in snd_soc_put_xr_sx()

When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220201155629.120510-5-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw_range()

When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220201155629.120510-4-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw_sx()

When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220201155629.120510-3-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw()

When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220201155629.120510-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Add API to count spi acpi resources

Some ACPI nodes may have more than one Spi Resource.
To be able to handle these case, its necessary to have
a way of counting these resources.

Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-5-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Support selection of the index of the ACPI Spi Resource before alloc

If a node contains more than one SPI resource it may be necessary to
use an index to select which one you want to allocate a spi device for.

Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Create helper API to lookup ACPI info for spi device

This can then be used to find a spi resource inside an
ACPI node, and allocate a spi device.

Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Make spi_alloc_device and spi_add_device public again

This functions were previously made private since they
were not used. However, these functions will be needed
again.

Partial revert of commit da21fde0fdb3
("spi: Make several public functions private to spi.c")

Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-2-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge tag 'asoc-fix-v5.17-rc2' of https://git./linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v5.17

Quite a few fixes here, including an unusually large set in the core
spurred on by various testing efforts as well as the usual small driver
fixes.  There are quite a few fixes for out of bounds writes in both the
core and the various Qualcomm drivers, plus a couple of fixes for
locking in the DPCM code.

ALSA: hda: Skip codec shutdown in case the codec is not registered

If the codec->registered is not set then it means that pm_runtime is
not yet enabled and the codec->pcm_list_head has not been initialized.

The access to the not initialized pcm_list_head will lead a kernel crash
during shutdown.

Reported-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Fixes: b98444ed597d ("ALSA: hda: Suspend codec at shutdown")
Link: https://lore.kernel.org/r/20220201112144.29411-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: usb-audio: Correct quirk for VF0770

This device provides both audio and video. The original quirk added in
commit 48827e1d6af5 ("ALSA: usb-audio: Add quirk for VF0770") used
USB_DEVICE to match the vendor and product ID. Depending on module order,
if snd-usb-audio was asked first, it would match the entire device and
uvcvideo wouldn't get to see it. Change the matching to USB_AUDIO_DEVICE
to restore uvcvideo matching in all cases.

Fixes: 48827e1d6af5 ("ALSA: usb-audio: Add quirk for VF0770")
Reported-by: Jukka Heikintalo <heikintalo.jukka@gmail.com>
Tested-by: Jukka Heikintalo <heikintalo.jukka@gmail.com>
Reported-by: Paweł Susicki <pawel.susicki@gmail.com>
Tested-by: Paweł Susicki <pawel.susicki@gmail.com>
Cc: <stable@vger.kernel.org> # 5.4, 5.10, 5.14, 5.15
Signed-off-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Link: https://lore.kernel.org/r/20220131183516.61191-1-hahnjo@hahnjo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: Replace acpi_bus_get_device()

Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().

No intentional functional impact.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/2828205.e9J7NaK4W3@kreacher
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Input: wm97xx: Simplify resource management

Since the commit in the Fixes tag below, 'wm->input_dev' is a managed
resource that doesn't need to be explicitly unregistered or freed (see
devm_input_allocate_device() documentation)

So, remove some unless line of code to slightly simplify it.

Fixes: c72f61e74073 ("Input: wm97xx: split out touchscreen registering")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87dce7e80ea9b191843fa22415ca3aef5f3cc2e6.1643529968.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>

ALSA: hda/realtek: Add quirk for ASUS GU603

The ASUS GU603 (Zephyrus M16 - SSID 1043:16b2) requires a quirk similar to
other ASUS devices for correctly routing the 4 integrated speakers. This
fixes it by adding a corresponding quirk entry, which connects the bass
speakers to the proper DAC.

Signed-off-by: Albert Geantă <albertgeanta@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220131010523.546386-1-albertgeanta@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda/realtek: Fix silent output on Gigabyte X570 Aorus Xtreme after reboot from Windows

This commit switches the Gigabyte X570 Aorus Xtreme from using the
ALC1220_FIXUP_CLEVO_P950 to the ALC1220_FIXUP_GB_X570 quirk. This fixes
the no-audio after reboot from windows problem.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205275
Signed-off-by: Christian Lachner <gladiac@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220129113243.93068-4-gladiac@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda/realtek: Fix silent output on Gigabyte X570S Aorus Master (newer chipset)

Newer versions of the X570 Master come with a newer revision of the
mainboard chipset - the X570S. These boards have the same ALC1220 codec
but seem to initialize the codec with a different parameter in Coef 0x7
which causes the output audio to be very low. We therefore write a
known-good value to Coef 0x7 to fix that. As the value is the exact same
as on the other X570(non-S) boards the same quirk-function can be shared
between both generations.

This commit adds the Gigabyte X570S Aorus Master to the list of boards
using the ALC1220_FIXUP_GB_X570 quirk. This fixes both, the silent output
and the no-audio after reboot from windows problems.

This work has been tested by the folks over at the level1techs forum here:
https://forum.level1techs.com/t/has-anybody-gotten-audio-working-in-linux-on-aorus-x570-master/154072

Signed-off-by: Christian Lachner <gladiac@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220129113243.93068-3-gladiac@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda/realtek: Add missing fixup-model entry for Gigabyte X570 ALC1220 quirks

The initial commit of the new Gigabyte X570 ALC1220 quirks lacked the
fixup-model entry in alc882_fixup_models[]. It seemed not to cause any ill
effects but for completeness sake this commit makes up for that.

Signed-off-by: Christian Lachner <gladiac@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220129113243.93068-2-gladiac@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: realtek: Fix race at concurrent COEF updates

The COEF access is done with two steps: setting the index then read or
write the data.  When multiple COEF accesses are performed
concurrently, the index and data might be paired unexpectedly.
In most cases, this isn't a big problem as the COEF setup is done at
the initialization, but some dynamic changes like the mute LED may hit
such a race.

For avoiding the racy COEF accesses, this patch introduces a new
mutex coef_mutex to alc_spec, and wrap the COEF accessing functions
with it.

Reported-by: Alexander Sergeyev <sergeev917@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220111195229.a77wrpjclqwrx4bx@localhost.localdomain
Link: https://lore.kernel.org/r/20220131075738.24323-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ASoC: ops: Check for negative values before reading them

The controls allow inputs to be specified as negative but our manipulating
them into register fields need to be done on unsigned variables so the
checks for negative numbers weren't taking effect properly. Do the checks
for negative values on the variable in the ABI struct rather than on our
local unsigned copy.

Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220128192443.3504823-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC DPCM lockdep fixes

Merge series from Takashi Iwai <tiwai@suse.de>:

This is the revised patches for addressing ASoC lockdep warnings due
to the recent DPCM locking refactoring.

ASoC: rt5682: Fix deadlock on resume

On resume from suspend the following chain of events can happen:
A rt5682_resume() -> mod_delayed_work() for jack_detect_work
B DAPM sequence starts ( DAPM is locked now)

A1. rt5682_jack_detect_handler() scheduled
 - Takes both jdet_mutex and calibrate_mutex
 - Calls in to rt5682_headset_detect() which tries to take DAPM lock, it
   starts to wait for it as B path took it already.
B1. DAPM sequence reaches the "HP Amp", rt5682_hp_event() tries to take
    the jdet_mutex, but it is locked in A1, so it waits.

Deadlock.

To solve the deadlock, drop the jdet_mutex, use the jack_detect_work to do
the jack removal handling, move the dapm lock up one level to protect the
most of the rt5682_jack_detect_handler(), but not the jack reporting as it
might trigger a DAPM sequence.
The rt5682_headset_detect() can be changed to static as well.

Fixes: 8deb34a90f063 ("ASoC: rt5682: fix the wrong jack type detected")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220126100325.16513-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: hdmi-codec: Fix OOB memory accesses

Correct size of iec_status array by changing it to the size of status
array of the struct snd_aes_iec958. This fixes out-of-bounds slab
read accesses made by memcpy() of the hdmi-codec driver. This problem
is reported by KASAN.

Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20220112195039.1329-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: Move debugfs removal out of spinlock

The recent fix for DPCM locking also covered the loop in
dpcm_be_disconnect() with the FE stream lock.  This caused an
unexpected side effect, thought: calling debugfs_remove_recursive() in
the spinlock may lead to lockdep splats as the code there assumes the
SOFTIRQ-safe context.

For avoiding the problem, this patch changes the disconnection
procedure to two phases: at first, the matching entries are removed
from the linked list, then the resources are freed outside the lock.

Fixes: b7898396f4bb ("ASoC: soc-pcm: Fix and cleanup DPCM locking")
Reported-and-tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220119155249.26754-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: Fix DPCM lockdep warning due to nested stream locks

The recent change for DPCM locking caused spurious lockdep warnings.
Actually the warnings are false-positive, as those are triggered due
to the nested stream locks for FE and BE.  Since both locks belong to
the same lock class, lockdep sees it as if a deadlock.

For fixing this, we need to take PCM stream locks for BE with the
nested lock primitives.  Since currently snd_pcm_stream_lock*() helper
assumes only the top-level single locking, a new helper function
snd_pcm_stream_lock_irqsave_nested() is defined for a single-depth
nested lock, which is now used in the BE DAI trigger that is always
performed inside a FE stream lock.

Fixes: b2ae80663008 ("ASoC: soc-pcm: serialize BE triggers")
Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com>
Reported-and-tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/73018f3c-9769-72ea-0325-b3f8e2381e30@redhat.com
Link: https://lore.kernel.org/alsa-devel/9a0abddd-49e9-872d-2f00-a1697340f786@samsung.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220119155249.26754-2-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: fsl: Add missing error handling in pcm030_fabric_probe

Add the missing platform_device_put() and platform_device_del()
before return from pcm030_fabric_probe in the error handling case.

Fixes: c912fa913446 ("ASoC: fsl: register the wm9712-codec")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220127131336.30214-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ALSA: hda: Fix signedness of sscanf() arguments

The %x format of sscanf() takes an unsigned int pointer, while we pass
a signed int pointer.  Practically it's OK, but this may result in a
compile warning.  Let's fix it.

Fixes: a235d5b8e550 ("ALSA: hda: Allow model option to specify PCI SSID alias")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220127135717.31751-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: usb-audio: initialize variables that could ignore errors

clang static analysis reports this representative issue
mixer.c:1548:35: warning: Assigned value is garbage or undefined
        ucontrol->value.integer.value[0] = val;
                                         ^ ~~~

The filter_error() macro allows errors to be ignored.
If errors can be ignored, initialize variables
so garbage will not be used.

Fixes: 48cc42973509 ("ALSA: usb-audio: Filter error from connector kctl ops, too")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220126182142.1184819-1-trix@redhat.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

kselftest: alsa: Add test case for writing invalid values

Attempt to write various invalid values for control types we know about and
check that something sensible happens. The ABI isn't quite as clearly
defined as one might like, rather than generating an error when an invalid
value is written many devices will silently rewrite the value into one that
is valid for the control. The exact value chosen is not predictable so in
the case the write succeeds we just check that the value we read back is
one that is valid for the control.

Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220125162824.3816659-1-broonie@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: Fix UAF of leds class devs at unbinding

The LED class devices that are created by HD-audio codec drivers are
registered via devm_led_classdev_register() and associated with the
HD-audio codec device.  Unfortunately, it turned out that the devres
release doesn't work for this case; namely, since the codec resource
release happens before the devm call chain, it triggers a NULL
dereference or a UAF for a stale set_brightness_delay callback.

For fixing the bug, this patch changes the LED class device register
and unregister in a manual manner without devres, keeping the
instances in hda_gen_spec.

Reported-by: Alexander Sergeyev <sergeev917@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220111195229.a77wrpjclqwrx4bx@localhost.localdomain
Link: https://lore.kernel.org/r/20220126145011.16728-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ASoC: qdsp6: q6apm-dai: only stop graphs that are started

Its possible that the sound card is just opened and closed without actually
playing stream, ex: if the audio file itself is missing.

Even in such cases we do call stop on graphs that are not yet started.
DSP can throw errors in such cases, so add a check to see if the graph
was started before stopping it.

Fixes: 9b4fe0f1cd79 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: wcd938x: fix return value of mixer put function

wcd938x_ear_pa_put_gain, wcd938x_set_swr_port and  wcd938x_set_compander
currently returns zero eventhough it changes the value.
Fix this, so that change notifications are sent correctly.

Fixes: e8ba1e05bdc01 ("ASoC: codecs: wcd938x: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: lpass-rx-macro: fix sidetone register offsets

For some reason we ended up with incorrect register offfset calcuations
for sidetone. regmap clearly throw errors when accessing these incorrect
registers as these do not belong to any read/write ranges.
so fix them to point to correct register offsets.

Fixes: f3ce6f3c9a99 ("ASoC: codecs: lpass-rx-macro: add iir widgets")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: codecs: wcd938x: fix incorrect used of portid

Mixer controls have the channel id in mixer->reg, which is not same
as port id. port id should be derived from chan_info array.
So fix this. Without this, its possible that we could corrupt
struct wcd938x_sdw_priv by accessing port_map array out of range
with channel id instead of port id.

Fixes: e8ba1e05bdc0 ("ASoC: codecs: wcd938x: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ALSA: usb-audio: scarlett2: Use struct_size() helper in scarlett2_usb()

Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.

Also, address the following sparse warnings:
sound/usb/mixer_scarlett_gen2.c:1064:28: warning: using sizeof on a flexible structure
sound/usb/mixer_scarlett_gen2.c:1065:29: warning: using sizeof on a flexible structure

Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220120211600.GA28841@embeddedor
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ASoC: ops: Reject out of bounds values in snd_soc_put_xr_sx()

We don't currently validate that the values being set are within the range
we advertised to userspace as being valid, do so and reject any values
that are out of range.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220124153253.3548853-4-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ops: Reject out of bounds values in snd_soc_put_volsw_sx()

We don't currently validate that the values being set are within the range
we advertised to userspace as being valid, do so and reject any values
that are out of range.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220124153253.3548853-3-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ops: Reject out of bounds values in snd_soc_put_volsw()

We don't currently validate that the values being set are within the range
we advertised to userspace as being valid, do so and reject any values
that are out of range.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220124153253.3548853-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 5.17-rc1

Merge tag 'perf-tools-for-v5.17-2022-01-22' of git://git./linux/kernel/git/acme/linux

Pull more perf tools updates from Arnaldo Carvalho de Melo:

 - Fix printing 'phys_addr' in 'perf script'.

 - Fix failure to add events with 'perf probe' in ppc64 due to not
   removing leading dot (ppc64 ABIv1).

 - Fix cpu_map__item() python binding building.

 - Support event alias in form foo-bar-baz, add pmu-events and
   parse-event tests for it.

 - No need to setup affinities when starting a workload or attaching to
   a pid.

 - Use path__join() to compose a path instead of ad-hoc snprintf()
   equivalent.

 - Override attr->sample_period for non-libpfm4 events.

 - Use libperf cpumap APIs instead of accessing the internal state
   directly.

 - Sync x86 arch prctl headers and files changed by the new
   set_mempolicy_home_node syscall with the kernel sources.

 - Remove duplicate include in cpumap.h.

 - Remove redundant err variable.

* tag 'perf-tools-for-v5.17-2022-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf tools: Remove redundant err variable
  perf test: Add parse-events test for aliases with hyphens
  perf test: Add pmu-events test for aliases with hyphens
  perf parse-events: Support event alias in form foo-bar-baz
  perf evsel: Override attr->sample_period for non-libpfm4 events
  perf cpumap: Remove duplicate include in cpumap.h
  perf cpumap: Migrate to libperf cpumap api
  perf python: Fix cpu_map__item() building
  perf script: Fix printing 'phys_addr' failure issue
  tools headers UAPI: Sync files changed by new set_mempolicy_home_node syscall
  tools headers UAPI: Sync x86 arch prctl headers with the kernel sources
  perf machine: Use path__join() to compose a path instead of snprintf(dir, '/', filename)
  perf evlist: No need to setup affinities when disabling events for pid targets
  perf evlist: No need to setup affinities when enabling events for pid targets
  perf stat: No need to setup affinities when starting a workload
  perf affinity: Allow passing a NULL arg to affinity__cleanup()
  perf probe: Fix ppc64 'perf probe add events failed' case

Merge tag 'trace-v5.17-3' of git://git./linux/kernel/git/rostedt/linux-trace

Pull ftrace fix from Steven Rostedt:
 "Fix s390 breakage from sorting mcount tables.

  The latest merge of the tracing tree sorts the mcount table at build
  time. But s390 appears to do things differently (like always) and
  replaces the sorted table back to the original unsorted one. As the
  ftrace algorithm depends on it being sorted, bad things happen when it
  is not, and s390 experienced those bad things.

  Add a new config to tell the boot if the mcount table is sorted or
  not, and allow s390 to opt out of it"

* tag 'trace-v5.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix assuming build time sort works for s390

ftrace: Fix assuming build time sort works for s390

To speed up the boot process, as mcount_loc needs to be sorted for ftrace
to work properly, sorting it at build time is more efficient than boot up
and can save milliseconds of time. Unfortunately, this change broke s390
as it will modify the mcount_loc location after the sorting takes place
and will put back the unsorted locations. Since the sorting is skipped at
boot up if it is believed that it was sorted at run time, ftrace can crash
as its algorithms are dependent on the list being sorted.

Add a new config BUILDTIME_MCOUNT_SORT that is set when
BUILDTIME_TABLE_SORT but not if S390 is set. Use this config to determine
if sorting should take place at boot up.

Link: https://lore.kernel.org/all/yt9dee51ctfn.fsf@linux.ibm.com/
Fixes: 72b3942a173c ("scripts: ftrace - move the sort-processing in ftrace_init")
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Tested-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

Merge tag 'kbuild-fixes-v5.17' of git://git./linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Bring include/uapi/linux/nfc.h into the UAPI compile-test coverage

 - Revert the workaround of CONFIG_CC_IMPLICIT_FALLTHROUGH

 - Fix build errors in certs/Makefile

* tag 'kbuild-fixes-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  certs: Fix build error when CONFIG_MODULE_SIG_KEY is empty
  certs: Fix build error when CONFIG_MODULE_SIG_KEY is PKCS#11 URI
  Revert "Makefile: Do not quote value for CONFIG_CC_IMPLICIT_FALLTHROUGH"
  usr/include/Makefile: add linux/nfc.h to the compile-test coverage

Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux

Pull bitmap updates from Yury Norov:

 - introduce for_each_set_bitrange()

 - use find_first_*_bit() instead of find_next_*_bit() where possible

 - unify for_each_bit() macros

* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
  vsprintf: rework bitmap_list_string
  lib: bitmap: add performance test for bitmap_print_to_pagebuf
  bitmap: unify find_bit operations
  mm/percpu: micro-optimize pcpu_is_populated()
  Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
  find: micro-optimize for_each_{set,clear}_bit()
  include/linux: move for_each_bit() macros from bitops.h to find.h
  cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
  tools: sync tools/bitmap with mother linux
  all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
  cpumask: use find_first_and_bit()
  lib: add find_first_and_bit()
  arch: remove GENERIC_FIND_FIRST_BIT entirely
  include: move find.h from asm_generic to linux
  bitops: move find_bit_*_le functions from le.h to find.h
  bitops: protect find_first_{,zero}_bit properly

perf tools: Remove redundant err variable

Return value from perf_event__process_tracing_data() directly instead
of taking this in another redundant variable.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/20220112080109.666800-1-chi.minghao@zte.com.cn
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf test: Add parse-events test for aliases with hyphens

Add a test which allows us to test parsing an event alias with hyphens.

Since these events typically do not exist on most host systems, add the
alias to the fake pmu.

Function perf_pmu__test_parse_init() has terms added to match known test
aliases.

Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi115@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/1642432215-234089-4-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf test: Add pmu-events test for aliases with hyphens

Add a test for aliases with hyphens in the name to ensure that the
pmu-events tables are as expects. There should be no reason why these sort
of aliases would be treated differently, but no harm in checking.

Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi115@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/1642432215-234089-3-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf parse-events: Support event alias in form foo-bar-baz

Event aliasing for events whose name in the form foo-bar-baz is not
supported, while foo-bar, foo_bar_baz, and other combinations are, i.e.
two hyphens are not supported.

The HiSilicon D06 platform has events in such form:

  $ ./perf list sdir-home-migrate

  List of pre-defined events (to be used in -e):

  uncore hha:
    sdir-home-migrate
   [Unit: hisi_sccl,hha]

  $ sudo ./perf stat -e sdir-home-migrate
  event syntax error: 'sdir-home-migrate'
                          \___ parser error
  Run 'perf list' for a list of valid events

   Usage: perf stat [<options>] [<command>]

   -e, --event <event>event selector. use 'perf list' to list available events

To support, add an extra PMU event symbol type for "baz", and add a new
rule in the bison file.

Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qi Liu <liuqi115@huawei.com>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: linuxarm@huawei.com
Link: https://lore.kernel.org/r/1642432215-234089-2-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf evsel: Override attr->sample_period for non-libpfm4 events

A previous patch preventing "attr->sample_period" values from being
overridden in pfm events changed a related behaviour in arm-spe.

Before said patch:

  perf record -c 10000 -e arm_spe_0// -- sleep 1

Would yield an SPE event with period=10000. After the patch, the period
in "-c 10000" was being ignored because the arm-spe code initializes
sample_period to a non-zero value.

This patch restores the previous behaviour for non-libpfm4 events.

Fixes: ae5dcc8abe31 (“perf record: Prevent override of attr->sample_period for libpfm4 events”)
Reported-by: Chase Conklin <chase.conklin@arm.com>
Signed-off-by: German Gomez <german.gomez@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: bpf@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: http://lore.kernel.org/lkml/20220118144054.2541-1-german.gomez@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf cpumap: Remove duplicate include in cpumap.h

Remove all but the first include of stdbool.h from cpumap.h.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20220117083730.863200-1-lv.ruyi@zte.com.cn
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf cpumap: Migrate to libperf cpumap api

Switch from directly accessing the perf_cpu_map to using the appropriate
libperf API when possible. Using the API simplifies the job of
refactoring use of perf_cpu_map.

Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: André Almeida <andrealmeid@collabora.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Miaoqian Lin <linmq006@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Song Liu <song@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Brennan <stephen.s.brennan@oracle.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Yury Norov <yury.norov@gmail.com>
Link: http://lore.kernel.org/lkml/20220122045811.3402706-3-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf python: Fix cpu_map__item() building

Value should be built as an integer.

Switch some uses of perf_cpu_map to use the library API.

Fixes: 6d18804b963b78dc ("perf cpumap: Give CPUs their own type")
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: André Almeida <andrealmeid@collabora.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Miaoqian Lin <linmq006@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Shunsuke Nakamura <nakamura.shun@fujitsu.com>
Cc: Song Liu <song@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Brennan <stephen.s.brennan@oracle.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Yury Norov <yury.norov@gmail.com>
Link: http://lore.kernel.org/lkml/20220122045811.3402706-2-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf script: Fix printing 'phys_addr' failure issue

Perf script was failed to print the phys_addr for SPE profiling.
One 'dummy' event is added by SPE profiling but it doesn't have PHYS_ADDR
attribute set, perf script then exits with error.

Now referring to 'addr', use evsel__do_check_stype() to check the type.

Before:

  # perf record -e arm_spe_0/branch_filter=0,ts_enable=1,pa_enable=1,load_filter=1,jitter=0,\
store_filter=0,min_latency=0,event_filter=2/ -p 4064384 -- sleep 3
  # perf script -F pid,tid,addr,phys_addr
  Samples for 'dummy:u' event do not have PHYS_ADDR attribute set. Cannot print 'phys_addr' field.

After:

  # perf record -e arm_spe_0/branch_filter=0,ts_enable=1,pa_enable=1,load_filter=1,jitter=0,\
store_filter=0,min_latency=0,event_filter=2/ -p 4064384 -- sleep 3
  # perf script -F pid,tid,addr,phys_addr
  4064384/4064384 ffff802f921be0d0      2f921be0d0
  4064384/4064384 ffff802f921be0d0      2f921be0d0

Reviewed-by: German Gomez <german.gomez@arm.com>
Signed-off-by: Yao Jin <jinyao5@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20220121065954.2121900-1-liwei391@huawei.com
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

certs: Fix build error when CONFIG_MODULE_SIG_KEY is empty

Since b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove
config_filename macro"), when CONFIG_MODULE_SIG_KEY is empty,
signing_key.x509 fails to build:

    CERT    certs/signing_key.x509
  Usage: extract-cert <source> <dest>
  make[1]: *** [certs/Makefile:78: certs/signing_key.x509] Error 2
  make: *** [Makefile:1831: certs] Error 2

Pass "" to the first argument of extract-cert to fix the build error.

Link: https://lore.kernel.org/linux-kbuild/20220120094606.2skuyb26yjlnu66q@lion.mk-sys.cz/T/#u
Fixes: b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove config_filename macro")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Michal Kubecek <mkubecek@suse.cz>

certs: Fix build error when CONFIG_MODULE_SIG_KEY is PKCS#11 URI

When CONFIG_MODULE_SIG_KEY is PKCS#11 URL (pkcs11:*), signing_key.x509
fails to build:

  certs/Makefile:77: *** target pattern contains no '%'.  Stop.

Due to the typo, $(X509_DEP) contains a colon.

Fix it.

Fixes: b8c96a6b466c ("certs: simplify $(srctree)/ handling and remove config_filename macro")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Revert "Makefile: Do not quote value for CONFIG_CC_IMPLICIT_FALLTHROUGH"

This reverts commit cd8c917a56f20f48748dd43d9ae3caff51d5b987.

Commit 129ab0d2d9f3 ("kbuild: do not quote string values in
include/config/auto.conf") provided the final solution.

Now reverting the temporary workaround.

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

usr/include/Makefile: add linux/nfc.h to the compile-test coverage

As linux/nfc.h userspace compilation was finally fixed by commits
79b69a83705e ("nfc: uapi: use kernel size_t to fix user-space builds")
and 7175f02c4e5f ("uapi: fix linux/nfc.h userspace compilation errors"),
there is no need to keep the compile-test exception for it in
usr/include/Makefile.

Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Merge branch 'akpm' (patches from Andrew)

Merge yet more updates from Andrew Morton:
 "This is the post-linux-next queue. Material which was based on or
  dependent upon material which was in -next.

  69 patches.

  Subsystems affected by this patch series: mm (migration and zsmalloc),
  sysctl, proc, and lib"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (69 commits)
  mm: hide the FRONTSWAP Kconfig symbol
  frontswap: remove support for multiple ops
  mm: mark swap_lock and swap_active_head static
  frontswap: simplify frontswap_register_ops
  frontswap: remove frontswap_test
  mm: simplify try_to_unuse
  frontswap: remove the frontswap exports
  frontswap: simplify frontswap_init
  frontswap: remove frontswap_curr_pages
  frontswap: remove frontswap_shrink
  frontswap: remove frontswap_tmem_exclusive_gets
  frontswap: remove frontswap_writethrough
  mm: remove cleancache
  lib/stackdepot: always do filter_irq_stacks() in stack_depot_save()
  lib/stackdepot: allow optional init and stack_table allocation by kvmalloc()
  proc: remove PDE_DATA() completely
  fs: proc: store PDE()->data into inode->i_private
  zsmalloc: replace get_cpu_var with local_lock
  zsmalloc: replace per zpage lock with pool->migrate_lock
  locking/rwlocks: introduce write_lock_nested
  ...

Merge tag '5.17-rc-part2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6

Pull cifs fixes from Steve French:

 - multichannel fixes, addressing additional reconnect and DFS scenarios

 - reenabling fscache support (indexing rewrite, metadata caching e.g.)

 - send additional version information during NTLMSSP negotiate to
   improve debugging

 - fix for a mount race

 - DFS fixes

 - fix for a memory leak for stable

* tag '5.17-rc-part2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module number
  smb3: send NTLMSSP version information
  cifs: Support fscache indexing rewrite
  cifs: cifs_ses_mark_for_reconnect should also update reconnect bits
  cifs: update tcpStatus during negotiate and sess setup
  cifs: make status checks in version independent callers
  cifs: remove repeated state change in dfs tree connect
  cifs: fix the cifs_reconnect path for DFS
  cifs: remove unused variable ses_selected
  cifs: protect all accesses to chan_* with chan_lock
  cifs: fix the connection state transitions with multichannel
  cifs: check reconnects for channels of active tcons too
  smb3: add new defines from protocol specification
  cifs: serialize all mount attempts
  cifs: quirk for STATUS_OBJECT_NAME_INVALID returned for non-ASCII dfs refs
  cifs: alloc_path_with_tree_prefix: do not append sep. if the path is empty
  cifs: clean up an inconsistent indenting
  cifs: free ntlmsspblob allocated in negotiate