dt/bindings: Add bindings for PIC32 watchdog peripheral

Document the devicetree bindings for the watchdog peripheral found on
Microchip PIC32 SoC class devices.

Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: module: fix incorrect IS_ERR_VALUE macro usages

IS_ERR_VALUE macro should be used only with unsigned long type.
Specifically it works incorrectly with longer types.

The patch follows conclusion from discussion on LKML [1][2].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2120927
[2]: http://permalink.gmane.org/gmane.linux.kernel/2150581

[ralf@linux-mips.org: While it may not immediately be obvious, the type
of st_value in the end is an unsigned long equivalent so the invocation
of IS_ERR_VALUE() was valid but I'm applying the patch anyway for
clarity.]

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12553/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: math-emu: Always propagate sNaN payload in quieting

Propagate sNaN payload in quieting in the legacy-NaN mode as well.  If
clearing the quiet bit would produce infinity, then set the next lower
trailing significand field bit, matching the SB-1 and BMIPS5000 hardware
implementations.  Some other MIPS FPU hardware implementations do
produce the default qNaN bit pattern instead.

This reverts some changes made for semantics preservation with commit
dc3ddf42 [MIPS: math-emu: Update sNaN quieting handlers], consequently
bringing back most of the semantics from before commit fdffbafb [Lots of
FPU bug fixes from Kjeld Borch Egevang.], except from the qNaN produced
in the infinity case.  Previously the default qNaN bit pattern was
produced in that case.

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11483/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ELF: Restructure personality macros

Update the ELF personality macros used for individual ABIs to make
actions in the same order across all of them and match formatting too.

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Fix uapi include in exported asm/siginfo.h

Since commit 8cb48fe169dd ("MIPS: Provide correct siginfo_t.si_stime"),
MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h
directly before defining MIPS' struct siginfo, in order to get the
necessary definitions needed for the siginfo struct without the generic
copy_siginfo() hitting compiler errors due to struct siginfo not yet
being defined.

Now that the generic copy_siginfo() is moved out to linux/signal.h we
can safely include asm-generic/siginfo.h before defining the MIPS
specific struct siginfo, which avoids the uapi/ include as well as
breakage due to generic copy_siginfo() being defined before struct
siginfo.

Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 8cb48fe169dd ("MIPS: Provide correct siginfo_t.si_stime")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Petr Malat <oss@malat.biz>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.0-
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

SIGNAL: Move generic copy_siginfo() to signal.h

The generic copy_siginfo() is currently defined in
asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which
defines the generic struct siginfo. However this makes it awkward for an
architecture to use it if it has to define its own struct siginfo (e.g.
MIPS and potentially IA64), since it means that asm-generic/siginfo.h
can only be included after defining the arch-specific siginfo, which may
be problematic if the arch-specific definition needs definitions from
uapi/asm-generic/siginfo.h.

It is possible to work around this by first including
uapi/asm-generic/siginfo.h to get the constants before defining the
arch-specific siginfo, and include asm-generic/siginfo.h after. However
uapi headers can't be included by other uapi headers, so that first
include has to be in an ifdef __kernel__, with the non __kernel__ case
including the non-UAPI header instead.

Instead of that mess, move the generic copy_siginfo() definition into
linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to
include asm-generic/siginfo.h and define the arch-specific siginfo, and
for the generic copy_siginfo() to see that arch-specific definition.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Petr Malat <oss@malat.biz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.0-
Patchwork: https://patchwork.linux-mips.org/patch/12478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Octeon: Mark some functions __init in smp.c

octeon_smp_setup and octeon_prepare_cpus are just used during initialization
period, so mark them as __init. And, octeon_prepare_cpus is just used in smp.c,
so make it static as well.

Signed-off-by: Yang Shi <yang.shi@windriver.com>
Cc: david.daney@cavium.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12574/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Improve BCM6368 device tree

- Remove unneeded leds0 alias.
- Switch to bcm6345-l1-intc interrupt controller.
- Use interrupt-controller instead of periph_intc and cpu_intc.
- Add uart1 node.
- Single ohci and ehci nodes.
- Avoid using underscores in node names.
- Rename uart aliases to serial.
- Remove blank line in cpus node.

[ralf@linux-mips.org: fix references in bcm96368mvwg.dts so the file keeps
building.]

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Improve BCM6328 device tree

- Remove unneeded leds0 alias.
- Switch to bcm6345-l1-intc interrupt controller.
- Use interrupt-controller instead of periph_intc and cpu_intc.
- Add uart1, ehci and ohci nodes.
- Refactor syscon and syscon-reboot.
- Avoid using underscores in node names.
- Rename uart aliases to serial.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add support for BCM63268

This SoC is very similar to BCM63168 and Broadcom usually refers to them as
BCM63268.
Add BCM63268 and missing BCM63168 to device tree documentation.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13042/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add device tree example for BCM6358

This adds a device tree example for SFR Neufbox4 (Sercomm version), which
also serves as a real example for brcm,bcm6358-leds.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13041/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add BCM6358 support

BCM6358 has a shared TLB which conflicts with current SMP support, so it must
be disabled for now.
BCM6358 uses >= 0xfffe0000 addresses for internal registers, which need to be
remapped (by using a simplified version of BRCM63xx ioremap.h).
However, 0xfff80000 is a better address, since it also covers BCM3368, leaving
the possibility to add it in the future.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13040/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

CPUFREQ: Loongson1: Replace goto out with return in ls1x_cpufreq_probe()

This patch replaces goto out with return in ls1x_cpufreq_probe().

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13056/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

CPUFREQ: Loongson1: Use devm_kzalloc() instead of global structure

This patch uses devm_kzalloc() instead of global structure.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13055/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

CPUFREQ: Loongson1: Use dev_get_platdata() to get platform_data

This patch uses dev_get_platdata() to get the platform_data
instead of referencing it directly.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13054/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

CPUFREQ: Loongson1: Replace kzalloc() with kcalloc()

This patch replaces kzalloc() with kcalloc() when allocating
frequency table, and remove unnecessary 'out of memory' message.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13053/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

CPUFREQ: Loongson1: Rename the file to loongson1-cpufreq.c

This patch renames the file to loongson1-cpufreq.c,
and also includes some minor updates.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Pretty print BMIPS5200 processor name

Just to ease debugging of multiplatform kernel, make sure we print
"Broadcom BMIPS5200" for the BMIPS5200 implementation instead of
Broadcom BMIPS5000.

Fixes: 68e6a78373a6d ("MIPS: BMIPS: Add PRId for BMIPS5200 (Whirlwind)")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13014/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add cpu-feature-overrides.h

BMIPS_GENERIC being multiplatform and intended to support BMIPS3200,
BMIPS3300, BMIPS4350, BMIPS4380 and BMIPS5000-class processors, there is
not much more we can put in there since they do not share the same I and
D cache line sizes at all (doubled for every new generation
essentially), some processors have a S-cache, some don't, some have a
FPU, some don't.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13013/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: local_r4k___flush_cache_all needs to blast S-cache

local_r4k___flush_cache_all() is missing a special check for BMIPS5000
processors, we need to blast the S-cache, just like other MTI processors
since we have an inclusive cache. We also need an additional __sync() to
make sure this is completed.

Fixes: d74b0172e4e2c ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13012/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Clear MIPS_CACHE_ALIASES earlier

BMIPS5000 and BMIPS5200 processor have no D cache aliases, and this is
properly handled by the per-CPU override added at the end of
r4k_cache_init(), the problem is that the output of probe_pcache()
disagrees with that, since this is too late:

Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes

With the change moved earlier, we now have a consistent output with the
settings we are intending to have:

Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, no aliases, linesize 32 bytes

Fixes: d74b0172e4e2c ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: BMIPS5000 has I cache filing from D cache

BMIPS5000 and BMIPS52000 processors have their I-cache filling from the
D-cache. Since BMIPS_GENERIC does not provide (yet) a
cpu-feature-overrides.h file, this was not set anywhere, so make sure
the R4K cache detection takes care of that.

Fixes: d74b0172e4e2c ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13010/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Enable partition parser in defconfig

Enable CONFIG_MTD_BCM63XX_PARTS in arch/mips/configs/bmips_be_defconfig
since this is a necessary option to parse the built-in flash partition
table on BMIPS big-endian SoCs (Cable Modem and DSL).

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12256/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM63xx: Enable partition parser in defconfig

Enable CONFIG_MTD_BCM63XX_PARTS in arch/mips/configs/bcm63xx_defconfig
since this is a necessary option to parse the built-in flash partition
table on BCM63xx SoCs.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12255/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MAINTAINERS: add Loongson1 architecture entry

This patch adds Loongson1 architecture entry.

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: dmaengine@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/13034/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson1B: Some updates/fixes for LS1B

- Add DMA device
- Add NAND device
- Add GPIO device
- Add LED device
- Update the defconfig and rename it to loongson1b_defconfig
- Fix ioremap size
- Other minor fixes

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: dmaengine@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/13033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

ld-version: Drop the 4th and 5th version components

... making upstream development binutils snapshots work as expected,
e.g.:

$ mips64el-linux-ld --version
GNU ld (GNU Binutils) 2.20.1.20100303
[...]
$

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Acked-by: Michal Marek <mmarek@suse.cz>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kbuild@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12537/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Fix interrupt and remove needless properties

Fixes wrong bcm7425 SATA AHCI hardware interrupt property value with
periph_intc and SATA PHY unit address, and removes needless
brcm,broken-{ncq,phy} properties what are not used anywhere.

Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Dragan Stancevic <dragan.stancevic@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13017/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add support UART, I2C, SATA device

Add UART, I2C, SATA device tree nodes on Broadcom BCM7xxx MIPS-based
platforms.

Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Dragan Stancevic <dragan.stancevic@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13016/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Kconfig: replace OPROFILE=n to !OPROFILE

In Kconfig "=n" is not correct syntax, "!" is the preferred way for
false-positive expression.

Signed-off-by: Yang Shi <yang.shi@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12572/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: KASLR: Print relocation Information on boot

When debugging a relocated kernel, the addresses of the relocated
symbols and the offset applied is essential information. If the kernel
is compiled with debugging information, then print this information
during bootup using the same function as the panic notifier.

[ralf@linux-mips.org: Fixed spelling mistake pointed out by
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>.]

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12989/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Kernel: Implement KASLR using CONFIG_RELOCATABLE

This patch adds KASLR to the MIPS kernel.

Entropy is derived from the banner, which will change every build and
random_get_entropy() which should provide additional runtime entropy.
Additionally the bootloader may pass entropy via the /chosen/kaslr-seed
node in device tree.

The kernel is relocated by up to RANDOMIZE_BASE_MAX_OFFSET bytes from
its link address (PHYSICAL_START). Because relocation happens so early
in the kernel boot, the amount of physical memory has not yet been
determined. This means the only way to limit relocation within the
available memory is via Kconfig.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12990/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Introduce plat_get_fdt a platform API to retrieve the FDT

Early access to the kernel command line requires early access to the FDT
for platforms which pass the command line within the device tree. There
was no common way to retrieve the location of the FDT without incurring
side effects, such as plat_mem_setup which, on Malta at least,
initializes a bunch of other stuff.

This patch adds plat_get_ftd() for IMG platforms.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12988/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add CONFIG_RELOCATABLE Kconfig option

Add option to KConfig to enable the kernel to relocate itself at
runtime.

Relocation is supported R2 and later of the MIPS architecture, 32bit
and 64bit. The platform is also required to provide support through
plat_get_fdt() added in a later patch.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12987/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: bootmem: When relocatable, free memory below kernel

The kernel reserves all memory before the _end symbol as bootmem,
however, once the kernel can be relocated elsewhere in memory this may
result in a large amount of wasted memory. The assumption is that the
memory between the link and relocated address of the kernel may be
released back to the available memory pool.

Memory statistics for a Malta with the kernel relocating by
16Mb, without the patch:
Memory: 105952K/131072K available (4604K kernel code, 242K rwdata,
892K rodata, 1280K init, 183K bss, 25120K reserved, 0K cma-reserved)
And with the patch:
Memory: 122336K/131072K available (4604K kernel code, 242K rwdata,
892K rodata, 1280K init, 183K bss, 8736K reserved, 0K cma-reserved)

The 16Mb offset is removed from the reserved region and added back to
the available region.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12986/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Call relocate_kernel if CONFIG_RELOCATABLE=y

If CONFIG_RELOCATABLE is enabled, call relocate_kernel.

This function will return the entry point of the relocated kernel if
copy/relocate is sucessful or the original entry point if not. The stack
pointer must then be pointed into the new image.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12984/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Kernel: Add relocate.c

arch/mips/kernel/relocate.c contains the functions necessary to relocate
the kernel elsewhere in memory

The kernel makes a copy of itself at the new address. It uses the
relocation table inserted by the relocs tool to fix symbol references
within the new image.

If copy/relocation is sucessful then the entry point of the new kernel
is returned, otherwise fall back to starting the kernel in place.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12985/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Generate relocation table when CONFIG_RELOCATABLE

When CONFIG_RELOCATABLE is enabled (added in later patch) add
--emit-relocs to vmlinux LDFLAGS so that fully linked vmlinux contains
relocation information.

Run the previously added relocs tool to fill in the .data.relocs section
of vmlinux with a table of relocations. The relocs tool will also remove
(mark as 0 length) the relocation sections added to vmlinux.

When vmlinux is passed to the boot makefile for conversion into a boot
image the now empty relocation sections will be removed and the
populated relocation table will be included in the binary image.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12983/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Reserve space for relocation table

When CONFIG_RELOCATABLE is enabled, add a new section in the memory map
to be filled with relocation data.

CONFIG_RELOCATION_TABLE_SIZE allows the amount of space reserved to be
adjusted if necessary.

The relocs tool will populate this reserved space with relocation
information. The space is reserved within the elf by filling it with
0's, and an invalid entry is left at the start of the space such that
kernel relocation will be aborted if the table is empty.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12982/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: tools: Build relocs tool

Build the relocs tool as part of the kbuild

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12980/
Patchwork: https://patchwork.linux-mips.org/patch/13242/
Patchwork: https://patchwork.linux-mips.org/patch/13233/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: tools: Add relocs tool

This tool is based on the x86/boot/tools/relocs tool.

It parses the relocations present in the vmlinux elf file, building a
table of relocations that will be necessary to run the kernel from an
address other than its link address. This table is inserted into the
vmlinux elf, in the .data.relocs section. The table is subsequently used
by the code in arch/mips/kernel/relocate.c (added later) to relocate the
kernel.

The tool, by default, also marks all relocation sections as 0 length.
This is due to objcopy currently being unable to handle copying the
relocations between 64 and 32 bit elf files as is done when building a
64 bit kernel.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12981/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

secomp: Constify mode1 syscall whitelist

These values are constant and should be marked as such.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Will Drewry <wad@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12979/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: seccomp: Support compat with both O32 and N32

Previously the seccomp would only support strict mode on O32 userland
programs when the kernel had support for both O32 and N32 ABIs. Remove
kludge and support both ABIs.

With this patch in place, the seccomp_bpf self test now passes
global.mode_strict_support with N32 userland.

Suggested-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12917/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

seccomp: Get compat syscalls from asm-generic header

Move retrieval of compat syscall numbers into inline function defined in
asm-generic header so that arches may override it.

[ralf@linux-mips.org: Resolve merge conflict.]

Suggested-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will Drewry <wad@chromium.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12978/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: scall: Handle seccomp filters which redirect syscalls

Commit d218af78492a ("MIPS: scall: Always run the seccomp syscall
filters") modified the syscall code to always call the seccomp filters,
but missed the case where a filter may redirect the syscall, as
revealed by the seccomp_bpf self test.

The syscall path now restores the syscall from the stack after the
filter rather than saving it locally. Syscall number checking and
syscall function table lookup is done after the filter may have run such
that redirected syscalls are also checked, and executed.

The regular path of syscall number checking and pointer lookup is also
made more consistent between ABIs with scall64-64.S being the reference.

With this patch in place, the seccomp_bpf self test now passes
TRACE_syscall.syscall_redirected and TRACE_syscall.syscall_dropped on
all MIPS ABIs.

Fixes: d218af78492a ("MIPS: scall: Always run the seccomp syscall filters")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Eric B Munson <emunson@akamai.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12916/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Support sending SIG_SYS to 32bit userspace from 64bit kernel

The seccomp_bpf self test revealed that a 64bit kernel delivered an
invalid SIG_SYS to a 32bit userspace, because it was falling into the
default of the switch statement. Add a case to handle delivering the
signal.

With this patch, the seccomp_bpf self test now passes the TRAP.handler
case with O32 and N32 userlands.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Amanieu d'Antras <amanieu@gmail.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12915/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

selftests/seccomp: add MIPS self-test support

This adds self-test support on MIPS, based on RFC patch from Kees Cook.
Modifications from the RFC:
- support the O32 syscall which passes the real syscall number in a0.
- Use PTRACE_{GET,SET}REGS
- Because SYSCALL_NUM and SYSCALL_RET are the same register, it is not
  possible to test modifying the syscall return value when skipping,
  since both would need to set the same register. Therefore modify that
  test case to just detect the skipped test.
Tested on MIPS32r2 / MIPS64r2 with O32, N32 and N64 userlands.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Will Drewry <wad@chromium.org>
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12977/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

pinctrl/lantiq: update devicetree binding in dts file

This patch updates the compatible string in the easy50712.dts file to the new
"lantiq,danube-pinctrl".

Signed-off-by: Martin Schiller <mschiller@tdt.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: robh+dt@kernel.org
Cc: pawel.moll@arm.com
Cc: mark.rutland@arm.com
Cc: ijc+devicetree@hellion.org.uk
Cc: galak@codeaurora.org
Cc: john@phrozen.org
Cc: hauke@hauke-m.de
Cc: jogo@openwrt.org
Cc: daniel.schwierzeck@gmail.com
Cc: linux-gpio@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11589/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

crash_dump: Add vmcore_elf32_check_arch

parse_crash_elf{32|64}_headers will check the headers via the
elf_check_arch respectively vmcore_elf64_check_arch macro.

The MIPS architecture implements those two macros differently.
In order to make the differentiation more explicit, let's introduce
an vmcore_elf32_check_arch to allow the archs to overwrite it.

Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Suggested-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12535/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: Add brcm, bcm6345-l1-intc device tree binding

Add device tree binding for the BCM6345 interrupt controller.

This controller is similar to the SMP-capable BCM7038 and
the BCM3380 but with packed interrupt registers.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11804/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: defconfigs: Remove CONFIG_IPV6_PRIVACY

Option is long gone, see

  5d9efa7ee99e ("ipv6: Remove privacy config option.")

Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/12919/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Use generic clkdev.h header

The generic header file is equivalent to the MIPS one, so use the
generic one instead.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Sync icache & dcache in set_pte_at

It's possible for pages to become visible prior to update_mmu_cache
running if a thread within the same address space preempts the current
thread or runs simultaneously on another CPU. That is, the following
scenario is possible:

    CPU0                            CPU1

    write to page
    flush_dcache_page
    flush_icache_page
    set_pte_at
                                    map page
    update_mmu_cache

If CPU1 maps the page in between CPU0's set_pte_at, which marks it valid
& visible, and update_mmu_cache where the dcache flush occurs then CPU1s
icache will fill from stale data (unless it fills from the dcache, in
which case all is good, but most MIPS CPUs don't have this property).
Commit 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.")
attempted to fix that by performing the dcache flush in
flush_icache_page such that it occurs before the set_pte_at call makes
the page visible. However it has the problem that not all code that
writes to pages exposed to userland call flush_icache_page. There are
many callers of set_pte_at under mm/ and only 2 of them do call
flush_icache_page. Thus the race window between a page becoming visible
& being coherent between the icache & dcache remains open in some cases.

To illustrate some of the cases, a WARN was added to __update_cache with
this patch applied that triggered in cases where a page about to be
flushed from the dcache was not the last page provided to
flush_icache_page. That is, backtraces were obtained for cases in which
the race window is left open without this patch. The 2 standout examples
follow.

When forking a process:

[   15.271842] [<80417630>] __update_cache+0xcc/0x188
[   15.277274] [<80530394>] copy_page_range+0x56c/0x6ac
[   15.282861] [<8042936c>] copy_process.part.54+0xd40/0x17ac
[   15.289028] [<80429f80>] do_fork+0xe4/0x420
[   15.293747] [<80413808>] handle_sys+0x128/0x14c

When exec'ing an ELF binary:

[   14.445964] [<80417630>] __update_cache+0xcc/0x188
[   14.451369] [<80538d88>] move_page_tables+0x414/0x498
[   14.457075] [<8055d848>] setup_arg_pages+0x220/0x318
[   14.462685] [<805b0f38>] load_elf_binary+0x530/0x12a0
[   14.468374] [<8055ec3c>] search_binary_handler+0xbc/0x214
[   14.474444] [<8055f6c0>] do_execveat_common+0x43c/0x67c
[   14.480324] [<8055f938>] do_execve+0x38/0x44
[   14.485137] [<80413808>] handle_sys+0x128/0x14c

These code paths write into a page, call flush_dcache_page then call
set_pte_at without flush_icache_page inbetween. The end result is that
the icache can become corrupted & userland processes may execute
unexpected or invalid code, typically resulting in a reserved
instruction exception, a trap or a segfault.

Fix this race condition fully by performing any cache maintenance
required to keep the icache & dcache in sync in set_pte_at, before the
page is made valid. This has the added bonus of ensuring the cache
maintenance always happens in one location, rather than being duplicated
in flush_icache_page & update_mmu_cache. It also matches the way other
architectures solve the same problem (see arm, ia64 & powerpc).

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Fixes: 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.")
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # v4.1+
Patchwork: https://patchwork.linux-mips.org/patch/12722/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Handle highmem pages in __update_cache

The following patch will expose __update_cache to highmem pages. Handle
them by mapping them in for the duration of the cache maintenance, just
like in __flush_dcache_page. The code for that isn't shared because we
need the page address in __update_cache so sharing became messy. Given
that the entirity is an extra 5 lines, just duplicate it.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # v4.1+
Patchwork: https://patchwork.linux-mips.org/patch/12721/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Flush highmem pages in __flush_dcache_page

When flush_dcache_page is called on an executable page, that page is
about to be provided to userland & we can presume that the icache
contains no valid entries for its address range. However if the icache
does not fill from the dcache then we cannot presume that the pages
content has been written back as far as the memories that the dcache
will fill from (ie. L2 or further out).

This was being done for lowmem pages, but not for highmem which can lead
to icache corruption. Fix this by mapping highmem pages & flushing their
content from the dcache in __flush_dcache_page before providing the page
to userland, just as is done for lowmem pages.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12720/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Flush dcache for flush_kernel_dcache_page

The flush_kernel_dcache_page function was previously essentially a nop.
This is incorrect for MIPS, where if a page has been modified & either
it aliases or it's executable & the icache doesn't fill from dcache then
the content needs to be written back from dcache to the next level of
the cache hierarchy (which is shared with the icache).

Implement this by simply calling flush_dcache_page, treating this
kmapped cache flush function (flush_kernel_dcache_page) exactly the same
as its non-kmapped counterpart (flush_dcache_page).

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12719/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: OCTEON: cavium_octeon_defconfig: enable all OCTEON SoC drivers

Some drivers for SoC provided functionality are missing.
Enable to those in defconfig to provide better build/testing coverage.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12750/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Detect DSP v3 support

DSPv3 is supported on all MIPSr6 systems which indicate support for DSPv2.

This doesn't require any changes to the kernel's handling of DSP
resources. The patch is to detect support and indicate it in /proc/cpuinfo

DSP v3 introduces a new instruction BPOSGE32C

Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12918/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

serial: pic32_uart: Add PIC32 UART driver

This adds UART and a serial console driver for Microchip PIC32 class
devices.

[ralf@linux-mips.org: Resolved merge conflict.]

Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-serial@vger.kernel.org
Cc: linux-api@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12101/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

dt/bindings: Add bindings for PIC32 UART driver

Document the devicetree bindings for the UART peripheral found on
Microchip PIC32 class devices.

Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12100/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: cpu: Convert MIPS_CPU_* defs to (1ull << x)

The MIPS_CPU_* definitions have now filled the first 32-bits, and are
getting longer since they're written in hex without zero padding. Adding
my 8 extra MIPS_CPU_* definitions which I haven't upstreamed yet this is
getting increasingly ugly as the comments get shifted progressively to
the right. Its also error prone, and I've seen this cause mistakes on 3
separate occasions now, not helped by it being a conflict hotspot.

Convert all the MIPS_CPU_* definitions to the form (1ull << x). Humans
are better at incrementing than shifting.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10045/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: cpu: Alter MIPS_CPU_* definitions to fill gap

The MIPS_CPU_* definitions accidentally missed bits 27..30 when
MIPS_CPU_EVA was added, and further definitions have continued from
there.

Shift all the definitions since MIPS_CPU_EVA right by 4 so there are no
gaps.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10044/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add early CPU initialization code

Port the stblinux-3.3 code to perform a bunch of CPU-specific initialization,
make it compatible with run-time detection of the CPU, and unroll the
brcmstb-specific macros: BDEV_RB(), BDEV_UNSET.

The "pref 30" disabling is done as a quirk. This is a preliminary change to
allow the use of the "rotr" instruction gated by cpu_has_rixi.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: john@phrozen.org
Cc: cernekee@gmail.com
Cc: jon.fraser@broadcom.com
Cc: pgynther@google.com
Cc: paul.burton@imgtec.com
Cc: ddaney.cavm@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12504/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: math-emu: dsemul: Remove an unused bit in ADDIUPC emulation

Avoid a reader's confusion, as the calculation is correct either way.

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12283/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

BUS: brcmstb_gisb: Hook to MIPS board_be_handler

MIPS kernels allow platforms to invoke a custom Bus Error handler, add the
necessary code to do this for Broadcom SoCs where the GISB bus error handler can be used.

We may get a bus error from an address decoded outside of the GISB bus space,
so we need to check the validity of such a capture before printing anything.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: cernekee@gmail.com
Cc: arnd@arndb.de
Cc: jaedon.shin@gmail.com
Cc: pgynther@google.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12284/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Octeon: Add Octeon III CN7xxx interface detection

Add basic CN7XXX interface detection.

This allows the kernel to boot with ethernet working as it initializes
the ethernet ports with SGMII instead of defaulting to RGMII routines.

Tested on the utm8 from Rhino Labs with a CN7130.

Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: janne.huttunen@nokia.com
Cc: aaro.koskinen@nokia.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12376/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Make flush_thread

Avoids function calls to an empty function.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Support R_MIPS_PC{16,21,26} rel-style relocs

MIPS32 code uses rel-style relocs, and MIPS32r6 modules may include
R_MIPS_PC16, R_MIPS_PC21 & R_MIPS_PC26 relocations. We thus need to
support these relocations in order to load MIPS32r6 kernel modules. This
patch adds such support, which is similar to the rela-style support in
module-rela.c but making use of the implicit addend from the instruction
encoding.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12435/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Support R_MIPS_PC{21,26} rela-style relocs

MIPS64 code uses rela-style relocs, and MIPS64r6 modules may include the
new R_MIPS_PC21 & R_MIPS_PC26 relocations. We thus need to support these
relocations in order to load MIPS64r6 kernel modules. They are similar
to the existing R_MIPS_PC16 relocation but applying to a wider field.
Implement support for them by genericising the existing R_MIPS_PC16
implementation such that it can be used for different field widths, and
calling it for all 3 reloc types.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12434/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: module: Make consistent use of pr_*()

The module relocation handling code has inconsistent use of printk() and
pr_*() functions. Convert printk() calls to use pr_err() and pr_warn().

[paul.burton@imgtec.com: Do the same thing in module.c]

Signed-off-by: Steven J. Hill <sjhill@realitydiluted.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12433/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Probe the M6250 CPU

Support probing the M6250 CPU now that cases for handling it have been
added where required in the core MIPS kernel code.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12375/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add M6250 cases to CPU switch statements

Add casses supporting the M6250 CPU to various switch statements in the
core MIPS kernel code that define behaviour dependent upon the CPU.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12374/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add M6250 PRID & cpu_type_enum values

Define the processor ID for the M6250 CPU and add a value to the enum
cpu_type_enum for the core.

[ralf@linux-mips.org: Fix merge conflict.]

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12373/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Probe the P6600 core

Support probing the P6600 core now that cases for handling it have been
added throughout the core MIPS kernel code.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12344/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add P6600 cases to CPU switch statements

Add cases supporting the P6600 CPU to various switch statements in
core MIPS kernel code that define behaviour dependent upon the CPU.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Petri Gynther <pgynther@google.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12343/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add P6600 PRID & cpu_type_enum values

Define the processor ID for the P6600 core and add a value to the enum
cpu_type_enum for the core.

[ralf@linux-mips.org: Fix merge conflict.]

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12342/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: <asm/cpu.h>: Reformat to 80 columns.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: SEAD3 can support MIPS32r6 CPUs

There are CPUs/bitfiles available for use with SEAD3 boards which
implement release 6 of the MIPS architecture. Allow building the kernel
for such a system.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12372/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: smp-cps: Stop printing EJTAG exceptions to UART

When CONFIG_MIPS_CPS_NS16550 is enabled, some register state is dumped
to the UART when an exception is taken via the BEV on secondary cores.
EJTAG exceptions are architecturally expected to be handled by the BEV
even when Status.BEV is 0. This effectively means that if userland
executes an sdbbp instruction on a secondary core then the kernel dumps
register state to the UART even though the exception is perfectly normal
& expected. Prevent this by simply not dumping information to the UART
for EJTAG exceptions.

Fixes: 609cf6f2291a ("MIPS: CPS: Early debug using an ns16550-compatible UART")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12341/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: smp-cps: Add nothreads kernel parameter

When debugging a new system or core it can be useful to disable the use
of multithreading. Introduce a "nothreads" kernel command line parameter
that can be set in order to do so.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12340/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: smp-cps: Support MIPSr6 Virtual Processors

Introduce support for bringing up Virtual Processors in MIPSr6 systems
as CPUs, much like their VPE parallel from the now-deprecated MT ASE.
The existing mips_cps_boot_vpes function fits the MIPSr6 architecture
pretty well - it can now simply write the mask of running VPs to the
VC_RUN register, rather than looping through each & starting or stopping
as appropriate as is done for VPEs from the MT ASE. Thus the VP support
is in general an extension & simplification of the existing MT ASE VPE
(aka SMVP) support.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12339/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: smp-cps: Skip core setup if coherent

In preparation for supporting MIPSr6 multithreading (ie. VPs) which will
begin execution from the core reset vector, skip core level setup if the
core is already coherent. This is never the case when a core is first
started, since boot_core explicitly clears the cores GCR_Cx_COH_EN
register, and always the case when secondary VPs start since the first
VP to start will have enabled coherence after initialising the core &
its caches.

One notable side effect of this patch is that eva_init gets called
slightly earlier, prior to mips_cps_core_init rather than after it.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: smp-cps: Pull boot config retrieval out of mips_cps_boot_vpes

The mips_cps_boot_vpes function previously included code to retrieve
pointers to the core & VPE boot configuration structs. These structures
were used both by mips_cps_boot_vpes and by its mips_cps_core_entry
callsite. In preparation for skipping the call to mips_cps_boot_vpes on
some invocations of mips_cps_core_entry, pull the calculation of those
pointers out into a separate function such that it can continue to be
shared.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: smp-cps: Pull cache init into a function

In preparation for further modifications to mips_cps_core_entry, pull
the L1 cache initialisation out into a separate function. This both
makes the code in mips_cps_core_entry read more clearly, particularly
when modifying it, and shortens it which will become important as code
is added that needs to continue to fit within the reset vector.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12336/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: smp-cps: Ensure our VP ident calculation is correct

When bringing up a CPU, ensure that its local ID as provided by the GIC
matches up with our calculation of it. This is vital, since if the
condition doesn't hold then we won't have configured interrupts
correctly for the VP.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12335/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Provide VP ID accessor

Provide a gic_read_local_vp_id() function to read the VCNUM field of the
GICs local VP_IDENT register. This will be used by a further patch to
check that the value reported by the GIC matches up with the kernels
calculation.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Use HW IDs for VPE_OTHER_ADDR

The Linux CPU number doesn't necessarily match up with the ID used for a
VP by hardware. Convert the CPU number to the HW ID using mips_cm_vp_id
when writing to the VP(E)_OTHER_ADDR register in order to ensure that we
correctly access registers for the VPs of secondary cores. This most
notably affects systems using CM3, such as those based around I6400.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: CM: Fix mips_cm_max_vp_width for UP kernels

Fix mips_cm_max_vp_width for UP kernels where it previously referenced
smp_num_siblings, which is not declared for UP kernels. This led to
build errors such as the following:

  drivers/built-in.o: In function `$L446':
  irq-mips-gic.c:(.text+0x1994): undefined reference to `smp_num_siblings'
  drivers/built-in.o:irq-mips-gic.c:(.text+0x199c): more undefined references to `smp_num_siblings' follow

On UP kernels simply return 1, leaving the reference to smp_num_siblings
in place only for SMP kernels.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12332/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: CM: Add CM GCR_BEV_BASE accessors

Generate accessor functions for the GCR_BEV_BASE register introduced by
CM3, for use by a later patch.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12331/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: CPC: Add start, stop and running CM3 CPC registers

Add the new CM3 registers for controlling bringing up and powering down
VPs on MIPSR6 cores.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12330/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: pm-cps: Avoid offset overflow on MIPSr6

This is similar to commit 934c79231c1b ("MIPS: asm: r4kcache: Add MIPS
R6 cache unroll functions"). The CACHE instruction has been redefined
for MIPSr6 and it reduced its offset field to 8 bits. This leads to
micro-assembler field overflow warnings when booting SMP MIPSr6 cores
like the following one:

Call Trace:
[<ffffffff8010af88>] show_stack+0x68/0x88
[<ffffffff8056ddf0>] dump_stack+0x68/0x88
[<ffffffff801305bc>] warn_slowpath_common+0x8c/0xc8
[<ffffffff80130630>] warn_slowpath_fmt+0x38/0x48
[<ffffffff80125814>] build_insn+0x514/0x5c0
[<ffffffff806ee134>] cps_gen_cache_routine.isra.3+0xe0/0x1b8
[<ffffffff806ee570>] cps_pm_init+0x364/0x9ec
[<ffffffff80100538>] do_one_initcall+0x90/0x1a8
[<ffffffff806e8c14>] kernel_init_freeable+0x160/0x21c
[<ffffffff8056b6a0>] kernel_init+0x10/0xf8
[<ffffffff801059f8>] ret_from_kernel_thread+0x14/0x1c

We fix this by incrementing the base register on every loop.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12329/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: traps: Make sure secondary cores have a sane ebase register

We shouldn't trust that the secondary cores will have a sane ebase register
(either from the bootloader or during the hardware design phase) so use the
ebase address as calculated by the boot CPU.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Petri Gynther <pgynther@google.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12328/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Detect MIPSr6 Virtual Processor support

MIPSr6 introduces support for "Virtual Processors", which are
conceptually similar to VPEs from the now-deprecated MT ASE. Detect
whether the system supports VPs using the VP bit in Config5, adding
cpu_has_vp for use by later patches.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12327/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath79: add initial support for DPT-Module

The following features are supported:

  * UART;
  * SPI-flash;
  * USB host;
  * GPIO key and LED.

Links:

  * https://dptechnics.com/shop/index.php?route=product/product&path=59&product_id=50
  * https://dptechnics.com/shop/index.php?route=product/product&path=59&product_id=63

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Daan Pape <daan@dptechnics.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12886/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

devicetree: add DPTechnics vendor id

Please see https://www.dptechnics.com/contact for details.

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Daan Pape <daan@dptechnics.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12885/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath79: add initial support for Onion Omega

The following features are supported:

  * UART;
  * SPI-flash;
  * USB host;
  * GPIO key and LED.

Please see https://onion.io/omega for details.

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: L. D. Pinney <ldpinney@gmail.com>
Cc: Boken Lin <bl@onion.io>
Cc: Jacky Huang <huangfangcheng@163.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

devicetree: add Onion Corporation vendor id

Please see https://onion.io/contact for details.

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12883/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath79: add initial support for Dragino MS14 (Dragino 2)

The following features are supported:

  * UART;
  * SPI-flash;
  * USB host;
  * GPIO keys and LEDs.

Links:

    * http://www.dragino.com/products/mother-board/item/71-ms14-p.html
    * https://wiki.openwrt.org/toh/dragino/ms14

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12882/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

devicetree: add Dragino vendor id

Please see http://www.dragino.com/about/about.html for details.

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ath79: add initial support for TP-LINK MR3020

The following features are supported:

  * UART;
  * SPI-flash;
  * USB host;
  * GPIO keys and LEDs.

Links:

  * http://www.tp-link.com/en/products/details/?model=TL-MR3020
  * http://wiki.openwrt.org/toh/tp-link/tl-mr3020
  * https://wikidevi.com/wiki/TP-LINK_TL-MR3020

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12880/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>