git.monstr.eu Git - linux-2.6-microblaze.git/log

drm/i915/skl+: consider max supported plane pixel rate while scaling

A display resolution is only supported if it meets all the restrictions
below for Maximum Pipe Pixel Rate.

The display resolution must fit within the maximum pixel rate output
from the pipe. Make sure that the display pipe is able to feed pixels at
a rate required to support the desired resolution.
For each enabled plane on the pipe {
    If plane scaling enabled {
Horizontal down scale amount = Maximum[1, plane horizontal size /
    scaler horizontal window size]
Vertical down scale amount = Maximum[1, plane vertical size /
    scaler vertical window size]
Plane down scale amount = Horizontal down scale amount *
    Vertical down scale amount
Plane Ratio = 1 / Plane down scale amount
    }
    Else {
Plane Ratio = 1
    }
    If plane source pixel format is 64 bits per pixel {
Plane Ratio = Plane Ratio * 8/9
    }
}

Pipe Ratio = Minimum Plane Ratio of all enabled planes on the pipe

If pipe scaling is enabled {
    Horizontal down scale amount = Maximum[1, pipe horizontal source size /
scaler horizontal window size]
    Vertical down scale amount = Maximum[1, pipe vertical source size /
scaler vertical window size]
    Note: The progressive fetch - interlace display mode is equivalent to a
2.0 vertical down scale
    Pipe down scale amount = Horizontal down scale amount *
Vertical down scale amount
    Pipe Ratio = Pipe Ratio / Pipe down scale amount
}

Pipe maximum pixel rate = CDCLK frequency * Pipe Ratio

In this patch our calculation is based on pipe downscale amount
(plane max downscale amount * pipe downscale amount) instead of Pipe
Ratio. So,
max supported crtc clock with given scaling = CDCLK / pipe downscale.
Flip will fail if,
current crtc clock > max supported crct clock with given scaling.

Changes since V1:
- separate out fixed_16_16 wrapper API definition
Changes since V2:
- Fix buggy crtc !active condition (Maarten)
- use intel_wm_plane_visible wrapper as per Maarten's suggestion
Changes since V3:
- Change failure return from ERANGE to EINVAL
Changes since V4:
- Rebase based on previous patch changes
Changes since V5:
- return EINVAL instead of continue (Maarten)
Changes since V6:
- Improve commit message
- Address review comment
Changes since V7:
- use !enable instead of !active
- rename config variable for consistency (Maarten)

Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526151546.25025-4-mahesh1.kumar@intel.com

drm/i915/skl: New ddb allocation algorithm

This patch implements new DDB allocation algorithm as per HW team
recommendation. This algo takecare of scenario where we allocate less DDB
for the planes with lower relative pixel rate, but they require more DDB
to work.
It also takes care of enabling same watermark level for each
plane in crtc, for efficient power saving.

Changes since v1:
- Rebase on top of Paulo's patch series

Changes since v2:
- Fix the for loop condition to enable WM

Changes since v3:
- Fix crash in cursor i-g-t reported by Maarten
- Rebase after addressing Paulo's comments
- Few other ULT fixes
Changes since v4:
- Rebase on drm-tip
- Added separate function to enable WM levels
Changes since v5:
- Fix a crash identified in skl-6770HQ system
Changes since v6:
- Address review comments from Matt
Changes since v7:
- Fix failure return in skl_compute_plane_wm (Matt)
- fix typo
Changes since v8:
- Always check cursor wm enable irrespective of total_data_rate
Changes since v9:
- fix typo

Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601055918.4601-1-mahesh1.kumar@intel.com

drm/i915: Always recompute watermarks when distrust_bios_wm is set, v2.

On some systems there can be a race condition in which no crtc state is
added to the first atomic commit. This results in all crtc's having a
null DDB allocation, causing a FIFO underrun on any update until the
first modeset.

Changes since v1:
- Do not take the connection_mutex, this is already done below.

Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Inspired-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 98d39494d375 ("drm/i915/gen9: Compute DDB allocation at atomic
check time (v4)")
Cc: <stable@vger.kernel.org> # v4.8+
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531154236.27180-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>

drm/i915: Prevent the system suspend complete optimization

Since

commit bac2a909a096c9110525c18cbb8ce73c660d5f71
Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Date:   Wed Jan 21 02:17:42 2015 +0100

    PCI / PM: Avoid resuming PCI devices during system suspend

PCI devices will default to allowing the system suspend complete
optimization where devices are not woken up during system suspend if
they were already runtime suspended. This however breaks the i915/HDA
drivers for two reasons:

- The i915 driver has system suspend specific steps that it needs to
  run, that bring the device to a different state than its runtime
  suspended state.

- The HDA driver's suspend handler requires power that it will request
  from the i915 driver's power domain handler. This in turn requires the
  i915 driver to runtime resume itself, but this won't be possible if the
  suspend complete optimization is in effect: in this case the i915
  runtime PM is disabled and trying to get an RPM reference returns
  -EACCESS.

Solve this by requiring the PCI/PM core to resume the device during
system suspend which in effect disables the suspend complete optimization.

Regardless of the above commit the optimization stayed disabled for DRM
devices until

commit d14d2a8453d650bea32a1c5271af1458cd283a0f
Author: Lukas Wunner <lukas@wunner.de>
Date:   Wed Jun 8 12:49:29 2016 +0200

    drm: Remove dev_pm_ops from drm_class

so this patch is in practice a fix for this commit. Another reason for
the bug staying hidden for so long is that the optimization for a device
is disabled if it's disabled for any of its children devices. i915 may
have a backlight device as its child which doesn't support runtime PM
and so doesn't allow the optimization either.  So if this backlight
device got registered the bug stayed hidden.

Credits to Marta, Tomi and David who enabled pstore logging,
that caught one instance of this issue across a suspend/
resume-to-ram and Ville who rememberd that the optimization was enabled
for some devices at one point.

The first WARN triggered by the problem:

[ 6250.746445] WARNING: CPU: 2 PID: 17384 at drivers/gpu/drm/i915/intel_runtime_pm.c:2846 intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746448] pm_runtime_get_sync() failed: -13
[ 6250.746451] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul
snd_hda_codec_realtek snd_hda_codec_generic ghash_clmulni_intel e1000e snd_hda_codec snd_hwdep snd_hda_core ptp mei_me pps_core snd_pcm lpc_ich mei prime_
numbers i2c_hid i2c_designware_platform i2c_designware_core [last unloaded: i915]
[ 6250.746512] CPU: 2 PID: 17384 Comm: kworker/u8:0 Tainted: G     U  W       4.11.0-rc5-CI-CI_DRM_334+ #1
[ 6250.746515] Hardware name:                  /NUC5i5RYB, BIOS RYBDWi35.86A.0362.2017.0118.0940 01/18/2017
[ 6250.746521] Workqueue: events_unbound async_run_entry_fn
[ 6250.746525] Call Trace:
[ 6250.746530]  dump_stack+0x67/0x92
[ 6250.746536]  __warn+0xc6/0xe0
[ 6250.746542]  ? pci_restore_standard_config+0x40/0x40
[ 6250.746546]  warn_slowpath_fmt+0x46/0x50
[ 6250.746553]  ? __pm_runtime_resume+0x56/0x80
[ 6250.746584]  intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746610]  intel_display_power_get+0x1b/0x40 [i915]
[ 6250.746646]  i915_audio_component_get_power+0x15/0x20 [i915]
[ 6250.746654]  snd_hdac_display_power+0xc8/0x110 [snd_hda_core]
[ 6250.746661]  azx_runtime_resume+0x218/0x280 [snd_hda_intel]
[ 6250.746667]  pci_pm_runtime_resume+0x76/0xa0
[ 6250.746672]  __rpm_callback+0xb4/0x1f0
[ 6250.746677]  ? pci_restore_standard_config+0x40/0x40
[ 6250.746682]  rpm_callback+0x1f/0x80
[ 6250.746686]  ? pci_restore_standard_config+0x40/0x40
[ 6250.746690]  rpm_resume+0x4ba/0x740
[ 6250.746698]  __pm_runtime_resume+0x49/0x80
[ 6250.746703]  pci_pm_suspend+0x57/0x140
[ 6250.746709]  dpm_run_callback+0x6f/0x330
[ 6250.746713]  ? pci_pm_freeze+0xe0/0xe0
[ 6250.746718]  __device_suspend+0xf9/0x370
[ 6250.746724]  ? dpm_watchdog_set+0x60/0x60
[ 6250.746730]  async_suspend+0x1a/0x90
[ 6250.746735]  async_run_entry_fn+0x34/0x160
[ 6250.746741]  process_one_work+0x1f2/0x6d0
[ 6250.746749]  worker_thread+0x49/0x4a0
[ 6250.746755]  kthread+0x107/0x140
[ 6250.746759]  ? process_one_work+0x6d0/0x6d0
[ 6250.746763]  ? kthread_create_on_node+0x40/0x40
[ 6250.746768]  ret_from_fork+0x2e/0x40
[ 6250.746778] ---[ end trace 102a62fd2160f5e6 ]---

v2:
- Use the new pci_dev->needs_resume flag, to avoid any overhead during
  the ->pm_prepare hook. (Rafael)

v3:
- Update commit message to reference the actual regressing commit.
  (Lukas)

v4:
- Rebase on v4 of patch 1/2.

Fixes: d14d2a8453d6 ("drm: Remove dev_pm_ops from drm_class")
References: https://bugs.freedesktop.org/show_bug.cgi?id=100378
References: https://bugs.freedesktop.org/show_bug.cgi?id=100770
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: linux-pci@vger.kernel.org
Cc: <stable@vger.kernel.org> # v4.10.x: 4d071c3 - PCI/PM: Add needs_resume flag
Cc: <stable@vger.kernel.org> # v4.10.x
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Marta Lofstedt <marta.lofstedt@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1493726649-32094-2-git-send-email-imre.deak@intel.com

drm/i915/guc: Fix doorbell id selection

We are passing parameters in the wrong order to find next zero bit, and
when it doesn't find anything it returns size (offset in the code), which
is always zero.

For reference the function is defined as:
find_next_bit( *addr, size, offset )

The incorrect parameter order was added by commit abddffdf3620e
("drm/i915/guc: Sanitize GuC client initialization"). Luckily, currently
we only use a single guc client and a single doorbell, which happens to be
zero; therefore it isn't necessary to backport this fix (which would be for
v4.12).

Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531000546.30762-1-michel.thierry@intel.com

drm/i915/psr: disable psr2 for resolution greater than 32X20

psr1 is also disabled for panel resolution greater than 32X20.
Added psr2 check to disable only for psr2 panels having resolution
greater than 32X20.

issue was introduced by
commit-id : "acf45d11050abd751dcec986ab121cb2367dcbba"
commit message: "PSR2 is restricted to work with panel resolutions
upto 3200x2000, move the check to intel_psr_match_conditions and fully
block psr."

v2: (Rodrigo)
Add previous commit details which introduced the issue

Fixes: acf45d11050a ("drm/i915/psr: disable psr2 for resolution greater than 32X20")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Yaroslav Shabalin <yaroslav.shabalin@gmail.com>
Reported-by: Yaroslav Shabalin <yaroslav.shabalin@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: vathsala nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/49935bdff896ee3140bed471012b9f9110a863a4.1495729964.git.vathsala.nagaraju@intel.com

drm/i915: Hold a wakeref for probing the ring registers

Allow intel_engine_is_idle() to be called outside of the GT wakeref by
acquiring the device runtime pm for ourselves. This allows the function
to act as check after we assume the engine is idle and we release the GT
wakeref held whilst we have requests. At the moment, we do not call it
outside of an awake context but taking the wakeref as required makes it
more convenient to use for quick debugging in future.

[ 2613.401647] RPM wakelock ref not held during HW access
[ 2613.401684] ------------[ cut here ]------------
[ 2613.401720] WARNING: CPU: 5 PID: 7739 at drivers/gpu/drm/i915/intel_drv.h:1787 gen6_read32+0x21f/0x2b0 [i915]
[ 2613.401731] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_realtek coretemp snd_hda_codec_generic crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm r8169 mii mei_me lpc_ich mei prime_numbers [last unloaded: i915]
[ 2613.401823] CPU: 5 PID: 7739 Comm: drv_missed_irq Tainted: G     U          4.12.0-rc2-CI-CI_DRM_421+ #1
[ 2613.401825] Hardware name: MSI MS-7924/Z97M-G43(MS-7924), BIOS V1.12 02/15/2016
[ 2613.401840] task: ffff880409e3a740 task.stack: ffffc900084dc000
[ 2613.401861] RIP: 0010:gen6_read32+0x21f/0x2b0 [i915]
[ 2613.401863] RSP: 0018:ffffc900084dfce8 EFLAGS: 00010292
[ 2613.401869] RAX: 000000000000002a RBX: ffff8804016a8000 RCX: 0000000000000006
[ 2613.401871] RDX: 0000000000000006 RSI: ffffffff81cbf2d9 RDI: ffffffff81c9e3a7
[ 2613.401874] RBP: ffffc900084dfd18 R08: ffff880409e3afc8 R09: 0000000000000000
[ 2613.401877] R10: 000000008a1c483f R11: 0000000000000000 R12: 000000000000209c
[ 2613.401879] R13: 0000000000000001 R14: ffff8804016a8000 R15: ffff8804016ac150
[ 2613.401882] FS:  00007f39ef3dd8c0(0000) GS:ffff88041fb40000(0000) knlGS:0000000000000000
[ 2613.401885] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2613.401887] CR2: 00000000023717c8 CR3: 00000002e7b34000 CR4: 00000000001406e0
[ 2613.401889] Call Trace:
[ 2613.401912]  intel_engine_is_idle+0x76/0x90 [i915]
[ 2613.401931]  i915_gem_wait_for_idle+0xe6/0x1e0 [i915]
[ 2613.401951]  fault_irq_set+0x40/0x90 [i915]
[ 2613.401970]  i915_ring_test_irq_set+0x42/0x50 [i915]
[ 2613.401976]  simple_attr_write+0xc7/0xe0
[ 2613.401981]  full_proxy_write+0x4f/0x70
[ 2613.401987]  __vfs_write+0x23/0x120
[ 2613.401992]  ? rcu_read_lock_sched_held+0x75/0x80
[ 2613.401996]  ? rcu_sync_lockdep_assert+0x2a/0x50
[ 2613.401999]  ? __sb_start_write+0xfa/0x1f0
[ 2613.402004]  vfs_write+0xc5/0x1d0
[ 2613.402008]  ? trace_hardirqs_on_caller+0xe7/0x1c0
[ 2613.402013]  SyS_write+0x44/0xb0
[ 2613.402020]  entry_SYSCALL_64_fastpath+0x1c/0xb1
[ 2613.402022] RIP: 0033:0x7f39eded6670
[ 2613.402025] RSP: 002b:00007fffdcdcb1a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 2613.402030] RAX: ffffffffffffffda RBX: ffffffff81470203 RCX: 00007f39eded6670
[ 2613.402033] RDX: 0000000000000001 RSI: 000000000041bc33 RDI: 0000000000000006
[ 2613.402036] RBP: ffffc900084dff88 R08: 00007f39ef3dd8c0 R09: 0000000000000001
[ 2613.402038] R10: 0000000000000000 R11: 0000000000000246 R12: 000000000041bc33
[ 2613.402041] R13: 0000000000000006 R14: 0000000000000000 R15: 0000000000000000
[ 2613.402046]  ? __this_cpu_preempt_check+0x13/0x20
[ 2613.402052] Code: 01 9b fa e0 0f ff e9 28 fe ff ff 80 3d 6a dd 0e 00 00 0f 85 29 fe ff ff 48 c7 c7 48 19 29 a0 c6 05 56 dd 0e 00 01 e8 da 9a fa e0 <0f> ff e9 0f fe ff ff b9 01 00 00 00 ba 01 00 00 00 44 89 e6 48
[ 2613.402199] ---[ end trace 31f0cfa93ab632bf ]---

Fixes: 5400367a864d ("drm/i915: Ensure the engine is idle before manually changing HWS")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170530121334.17364-2-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Short-circuit i915_gem_wait_for_idle() if already idle

If the device is asleep (no GT wakeref), we know the GPU is already idle.
If we add an early return, we can avoid touching registers and checking
hw state outside of the assumed GT wakelock. This prevents causing such
errors whilst debugging:

[ 2613.401647] RPM wakelock ref not held during HW access
[ 2613.401684] ------------[ cut here ]------------
[ 2613.401720] WARNING: CPU: 5 PID: 7739 at drivers/gpu/drm/i915/intel_drv.h:1787 gen6_read32+0x21f/0x2b0 [i915]
[ 2613.401731] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_realtek coretemp snd_hda_codec_generic crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm r8169 mii mei_me lpc_ich mei prime_numbers [last unloaded: i915]
[ 2613.401823] CPU: 5 PID: 7739 Comm: drv_missed_irq Tainted: G     U          4.12.0-rc2-CI-CI_DRM_421+ #1
[ 2613.401825] Hardware name: MSI MS-7924/Z97M-G43(MS-7924), BIOS V1.12 02/15/2016
[ 2613.401840] task: ffff880409e3a740 task.stack: ffffc900084dc000
[ 2613.401861] RIP: 0010:gen6_read32+0x21f/0x2b0 [i915]
[ 2613.401863] RSP: 0018:ffffc900084dfce8 EFLAGS: 00010292
[ 2613.401869] RAX: 000000000000002a RBX: ffff8804016a8000 RCX: 0000000000000006
[ 2613.401871] RDX: 0000000000000006 RSI: ffffffff81cbf2d9 RDI: ffffffff81c9e3a7
[ 2613.401874] RBP: ffffc900084dfd18 R08: ffff880409e3afc8 R09: 0000000000000000
[ 2613.401877] R10: 000000008a1c483f R11: 0000000000000000 R12: 000000000000209c
[ 2613.401879] R13: 0000000000000001 R14: ffff8804016a8000 R15: ffff8804016ac150
[ 2613.401882] FS:  00007f39ef3dd8c0(0000) GS:ffff88041fb40000(0000) knlGS:0000000000000000
[ 2613.401885] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2613.401887] CR2: 00000000023717c8 CR3: 00000002e7b34000 CR4: 00000000001406e0
[ 2613.401889] Call Trace:
[ 2613.401912]  intel_engine_is_idle+0x76/0x90 [i915]
[ 2613.401931]  i915_gem_wait_for_idle+0xe6/0x1e0 [i915]
[ 2613.401951]  fault_irq_set+0x40/0x90 [i915]
[ 2613.401970]  i915_ring_test_irq_set+0x42/0x50 [i915]
[ 2613.401976]  simple_attr_write+0xc7/0xe0
[ 2613.401981]  full_proxy_write+0x4f/0x70
[ 2613.401987]  __vfs_write+0x23/0x120
[ 2613.401992]  ? rcu_read_lock_sched_held+0x75/0x80
[ 2613.401996]  ? rcu_sync_lockdep_assert+0x2a/0x50
[ 2613.401999]  ? __sb_start_write+0xfa/0x1f0
[ 2613.402004]  vfs_write+0xc5/0x1d0
[ 2613.402008]  ? trace_hardirqs_on_caller+0xe7/0x1c0
[ 2613.402013]  SyS_write+0x44/0xb0
[ 2613.402020]  entry_SYSCALL_64_fastpath+0x1c/0xb1
[ 2613.402022] RIP: 0033:0x7f39eded6670
[ 2613.402025] RSP: 002b:00007fffdcdcb1a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 2613.402030] RAX: ffffffffffffffda RBX: ffffffff81470203 RCX: 00007f39eded6670
[ 2613.402033] RDX: 0000000000000001 RSI: 000000000041bc33 RDI: 0000000000000006
[ 2613.402036] RBP: ffffc900084dff88 R08: 00007f39ef3dd8c0 R09: 0000000000000001
[ 2613.402038] R10: 0000000000000000 R11: 0000000000000246 R12: 000000000041bc33
[ 2613.402041] R13: 0000000000000006 R14: 0000000000000000 R15: 0000000000000000
[ 2613.402046]  ? __this_cpu_preempt_check+0x13/0x20
[ 2613.402052] Code: 01 9b fa e0 0f ff e9 28 fe ff ff 80 3d 6a dd 0e 00 00 0f 85 29 fe ff ff 48 c7 c7 48 19 29 a0 c6 05 56 dd 0e 00 01 e8 da 9a fa e0 <0f> ff e9 0f fe ff ff b9 01 00 00 00 ba 01 00 00 00 44 89 e6 48
[ 2613.402199] ---[ end trace 31f0cfa93ab632bf ]---

Fixes: 25112b64b3d2 ("drm/i915: Wait for all engines to be idle as part of i915_gem_wait_for_idle()")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170530121334.17364-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/gvt: Return -EIO if host GuC submission is enabled when loading GVT-g

Currently GVT-g cannot work properly when host GuC submission is
enabled, so make the driver loading failed in this case.

v2:
- use DRM_ERROR as it is a fatal message. (Chris)

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495878259-7733-2-git-send-email-chuanxiao.dong@intel.com

drm/i915/gvt: Return -EIO if host enable_execlists not enabled when loading GVT-g

GVT-g relies on the enable_execlists parameter in i915. If this option
is not enabled for GVT-g, should return -EIO to make i915 driver loading
failed.

v2:
- Use DMR_ERROR as it is a fatal message. (Chris)

Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/gvt: Add gvt options sanitize function

The intel_gvt_sanitize_options will sanitize the GVT related
options before doing initialize the GVT.

Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Remove toplevel struct_mutex locking from debugfs/i915_drop_caches

I have a plan to write a quick test to exercise concurrent usage of
i915_gem_shrink(), the simplest way looks to be to have multiple threads
using debugfs/i915_drop_caches. However, we currently take one lock over
the entire function, serialising the calls into i915_gem_shrink() so
reduce the lock coverage.

Testcase: igt/gem_shrink/reclaim
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170524162653.5446-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Add kerneldoc to describe i915_gem_object.vma_list

Add kerneldoc for the vma_list stored on the i915_gem_object, in
particular, documenting the expected ordering of elements -- i.e. that
we do expect GGTT VMA first followed by the ppGTT VMA.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170525204818.12044-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Convert intel_sdvo connector properties to atomic.

SDVO was the last connector that's still using the legacy paths
for properties, and this is with a reason!

This connector implements a lot of properties dynamically,
and some of them shared with the digital connector state,
so sdvo_connector_state subclasses intel_digital_connector_state.

set_property had a lot of validation, but this is handled in the
drm core, so most of the validation can die off. The properties
are written right before enabling the connector, since there is no
good way to update the properties without crtc.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-13-maarten.lankhorst@linux.intel.com

drm/i915: Handle force_audio correctly in intel_sdvo

Do the same as other connectors, attempt to detect hdmi audio in
the detect() callback, and only use the force_audio property as
override. Compute has_audio in pipe_config, and use that value
instead of the probed value directly.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-12-maarten.lankhorst@linux.intel.com

drm/i915: Convert intel_hdmi connector properties to atomic

intel_hdmi supports 3 properties, force_audio, broadcast rgb and
scaling mode. The last one is only created for eDP, so the is_eDP
in set_property is not required.

panel fitting and broadcast rgb are straightforward and only requires
changing compute_config.

force_audio is also used to force DVI mode, which means changes to
compute_config and mode_valid. mode_valid is called with
connection_mutex held, so it can safely dereference connector->state.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-11-maarten.lankhorst@linux.intel.com

drm/i915: Convert intel_dp properties to atomic, v2.

intel_dp supports 3 properties, scaling mode, broadcast rgb and
force_audio. intel_digital_connector handles the plumbing,
so we only have to hook this up in compute_config and init.

Changes since v1:
- Remove limited_color_range too, unused. (danvet)

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-10-maarten.lankhorst@linux.intel.com

drm/i915: Make intel_dp->has_audio reflect hw state only

Always detect if audio is available during edid detection.
With less magic switching it's easier to convert the dp connector
properties to atomic.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-9-maarten.lankhorst@linux.intel.com

drm/i915: Convert LVDS connector properties to atomic.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-8-maarten.lankhorst@linux.intel.com

drm/i915: Convert DSI connector properties to atomic.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-7-maarten.lankhorst@linux.intel.com

drm/i915: Add plumbing for digital connector state, v3.

Some atomic properties are common between the various kinds of
connectors, for example a lot of them use panel fitting mode.
It makes sense to put a lot of it in a common place, so each
connector can use it while they're being converted.

Implement the properties required for the connectors:
- scaling mode property
- force audio property
- broadcast rgb
- aspect ratio

While at it, make clear that intel_digital_connector_atomic_get_property
is a hack that has to be removed when all connector properties
are converted to atomic.

Changes since v1:
- Scaling mode and aspect ratio are partly handled in core now.
Changes since v2:
- Split out the scaling mode / aspect ratio changes to a preparation
patch.
- Use mode_changed for panel fitter, changes to this property
are checked by fastset.
- Allowed_scaling_modes is removed, handled through core now.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-6-maarten.lankhorst@linux.intel.com

drm/i915: Use per-connector scaling mode property

None of the intel connectors can use all types of scaling modes,
so only try the ones that are possible. This is another preparation
for connectors towards conversion to atomic.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-5-maarten.lankhorst@linux.intel.com
[mlankhorst: Use renamed drm_connector_attach_scaling_mode_property function]

drm/i915: Use atomic scaling_mode instead of panel.fitting_mode

The first step in converting connector properties to atomic is
wiring up the atomic state. We're still not completely supoprting
the scaling mode in the atomic case, but this is the first step
towards it.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-4-maarten.lankhorst@linux.intel.com

drm/i915: Remove decoupled MMIO code

This is a follow-up patch to the previous patch ([PATCH[1/2] drm/i915:
Disable decoupled MMIO) to remove the dead code for decoupled MMIO
implementation, as it won't be used any longer on GEN9LP.

Therefore, this patch reverts:

commit 85ee17ebeedd1af0dccd98f82ab4e644e29d84c0
Author: Praveen Paneri <praveen.paneri@intel.com>
Date: Tue Nov 15 22:49:20 2016 +0530

drm/i915/bxt: Broxton decoupled MMIO

Signed-off-by: Kai Chen <kai.chen@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523215812.18328-3-kai.chen@intel.com

drm/i915: Disable decoupled MMIO

The decoupled MMIO feature doesn't work as intended by HW team. Enabling
it with forcewake will only make debugging efforts more difficult, so
let's disable it.

Fixes: 85ee17ebeedd ("drm/i915/bxt: Broxton decoupled MMIO")
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Praveen Paneri <praveen.paneri@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Kai Chen <kai.chen@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523215812.18328-2-kai.chen@intel.com

Backmerge tag 'v4.12-rc3' into drm-next

Linux 4.12-rc3

Daniel has requested this for some drm-intel-next work.

Merge tag 'drm-intel-next-2017-05-29' of git://anongit.freedesktop.org/git/drm-intel into drm-next

More stuff for 4.13:

- skl+ wm fixes from Mahesh Kumar
- some refactor and tests for i915_sw_fence (Chris)
- tune execlist/scheduler code (Chris)
- g4x,g33 gpu reset improvements (Chris, Mika)
- guc code cleanup (Michal Wajdeczko, Michał Winiarski)
- dp aux backlight improvements (Puthikorn Voravootivat)
- buffer based guc/host communication (Michal Wajdeczko)

* tag 'drm-intel-next-2017-05-29' of git://anongit.freedesktop.org/git/drm-intel: (253 commits)
  drm/i915: Update DRIVER_DATE to 20170529
  drm/i915: Keep the forcewake timer alive for 1ms past the most recent use
  drm/i915/guc: capture GuC logs if FW fails to load
  drm/i915/guc: Introduce buffer based cmd transport
  drm/i915/guc: Disable send function on fini
  drm: Add definition for eDP backlight frequency
  drm/i915: Drop AUX backlight enable check for backlight control
  drm/i915: Consolidate #ifdef CONFIG_INTEL_IOMMU
  drm/i915: Only GGTT vma may be pinned and prevent shrinking
  drm/i915: Serialize GTT/Aperture accesses on BXT
  drm/i915: Convert i915_gem_object_ops->flags values to use BIT()
  drm/i915/selftests: Silence compiler warning in igt_ctx_exec
  drm/i915/guc: Skip port assign on first iteration of GuC dequeue
  drm/i915: Remove misleading comment in request_alloc
  drm/i915/g33: Improve reset reliability
  Revert "drm/i915: Restore lost "Initialized i915" welcome message"
  drm/i915/huc: Update GLK HuC version
  drm/i915: Check for allocation failure
  drm/i915/guc: Remove action status and statistics from debugfs
  drm/i915/g4x: Improve gpu reset reliability
  ...

drm/i915: Update DRIVER_DATE to 20170529

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Linux 4.12-rc3

Merge branch 'fixes' of git://git./linux/kernel/git/evalenti/linux-soc-thermal

Pull thermal SoC management fixes from Eduardo Valentin:

- fixes to TI SoC driver, Broadcom, qoriq

- small sparse warning fix on thermal core

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: broadcom: ns-thermal: default on iProc SoCs
  ti-soc-thermal: Fix a typo in a comment line
  ti-soc-thermal: Delete error messages for failed memory allocations in ti_bandgap_build()
  ti-soc-thermal: Use devm_kcalloc() in ti_bandgap_build()
  thermal: core: make thermal_emergency_poweroff static
  thermal: qoriq: remove useless call for of_thermal_get_trip_points()

Merge tag 'drm-misc-next-2017-05-26' of git://anongit.freedesktop.org/git/drm-misc into drm-next

UAPI Changes:
- Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ defines to the UAPI (Robert)

Cross-subsystem Changes:
- Standardize sync_file.txt documentation format (Mauro)

Core Changes:
- Turf drm_[cm]alloc functions for kvmalloc alternatives (Michal)
- Add optional mode_valid() hook to crtc/encoder/bridge (Jose)
- Improve documentation around mode validation/alteration (Daniel)
- Reduce sync_file construction time by deferring name creation (Chris)

Driver Changes:
- pl111: Wire up the clock divider and add debugfs (Eric)
- various: Fix include notation and remove -Iinclude/drm (Masahiro)
- stm: Add Benjamin Gaignard and Vincent Abriou as STM maintainers (Vincent)
- various: Miscellaneous trivial fixes to pl111/stm/vgem/vc4

Cc: Michal Hocko <mhocko@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Robert Foss <robert.foss@collabora.com>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* tag 'drm-misc-next-2017-05-26' of git://anongit.freedesktop.org/git/drm-misc: (55 commits)
  dma-buf/sync-file: Defer creation of sync_file->name
  sync_file.txt: standardize document format
  gpu: drm: gma500: remove two more dead variable
  drm/doc: Clarify mode_fixup vs. atomic_check a bit more
  drm/doc: Document adjusted/request modes a bit better
  drm: Add crtc/encoder/bridge->mode_valid() callbacks
  MAINTAINERS: update drm/stm maintainers list
  drm/stm: ltdc: fix duplicated arguments
  drm/pl111: Fix return value check in pl111_amba_probe()
  drm/amd: include <linux/delay.h> instead of "linux/delay.h"
  drm: Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ to UAPI
  drm/vgem: Fix return value check in vgem_init()
  drm/blend: Fix comment typ-o
  drm/stm: remove unneeded -Iinclude/drm compiler flag
  drm/vc4: fix include notation and remove -Iinclude/drm flag
  drm/pl111: Add a debugfs node to dump our registers.
  drm/pl111: make structure mode_config_funcs static
  drm/pl111: make structure pl111_display_funcs static
  drm/pl111: Register the clock divider and use it.
  drm: drop drm_[cm]alloc* helpers
  ...

Merge tag 'tty-4.12-rc3' of git://git./linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg KH:
"Here are some serial and tty fixes for 4.12-rc3. They are a bit bigger
  than normal, which is why I had them bake in linux-next for a few
  weeks and didn't send them to you for -rc2.

  They revert a few of the serdev patches from 4.12-rc1, and bring
  things back to how they were in 4.11, to try to make things a bit more
  stable there. Rob and Johan both agree that this is the way forward,
  so this isn't people squabbling over semantics. Other than that, just
  a few minor serial driver fixes that people have had problems with.

  All of these have been in linux-next for a few weeks with no reported
  issues"

* tag 'tty-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: altera_uart: call iounmap() at driver remove
  serial: imx: ensure UCR3 and UFCR are setup correctly
  MAINTAINERS/serial: Change maintainer of jsm driver
  serial: enable serdev support
  tty/serdev: add serdev registration interface
  serdev: Restore serdev_device_write_buf for atomic context
  serial: core: fix crash in uart_suspend_port
  tty: fix port buffer locking
  tty: ehv_bytechan: clean up init error handling
  serial: ifx6x60: fix use-after-free on module unload
  serial: altera_jtaguart: adding iounmap()
  serial: exar: Fix stuck MSIs
  serial: efm32: Fix parity management in 'efm32_uart_console_get_options()'
  serdev: fix tty-port client deregistration
  Revert "tty_port: register tty ports with serdev bus"
  drivers/tty: 8250: only call fintek_8250_probe when doing port I/O

Merge tag 'powerpc-4.12-4' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:
"Fix running SPU programs on Cell, and a few other minor fixes.

  Thanks to Alistair Popple, Jeremy Kerr, Michael Neuling, Nicholas
  Piggin"

* tag 'powerpc-4.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Add PPC_FEATURE userspace bits for SCV and DARN instructions
  powerpc/spufs: Fix hash faults for kernel regions
  powerpc: Fix booting P9 hash with CONFIG_PPC_RADIX_MMU=N
  powerpc/powernv/npu-dma.c: Fix opal_npu_destroy_context() call
  selftests/powerpc: Fix TM resched DSCR test with some compilers

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Thomas Gleixner:
"A series of fixes for X86:

   - The final fix for the end-of-stack issue in the unwinder
   - Handle non PAT systems gracefully
   - Prevent access to uninitiliazed memory
   - Move early delay calaibration after basic init
   - Fix Kconfig help text
   - Fix a cross compile issue
   - Unbreak older make versions"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
  x86/alternatives: Prevent uninitialized stack byte read in apply_alternatives()
  x86/PAT: Fix Xorg regression on CPUs that don't support PAT
  x86/watchdog: Fix Kconfig help text file path reference to lockup watchdog documentation
  x86/build: Permit building with old make versions
  x86/unwind: Add end-of-stack check for ftrace handlers
  Revert "x86/entry: Fix the end of the stack for newly forked tasks"
  x86/boot: Use CROSS_COMPILE prefix for readelf

Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull timer fixlet from Thomas Gleixner:
"Silence dmesg spam by making the posix cpu timer printks depend on
print_fatal_signals"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Make signal printks conditional

Merge branch 'ras-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull RAS fixes from Thomas Gleixner:
"Two fixlets for RAS:

   - Export memory_error() so the NFIT module can utilize it

   - Handle memory errors in NFIT correctly"

* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  acpi, nfit: Fix the memory error check in nfit_handle_mce()
  x86/MCE: Export memory_error()

Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf tooling fixes from Thomas Gleixner:

- Synchronization of tools and kernel headers

- A series of fixes for perf report addressing various failures:
    * Handle invalid maps proper
    * Plug a memory leak
    * Handle frames and callchain order correctly

- Fixes for handling inlines and children mode

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/include: Sync kernel ABI headers with tooling headers
  perf tools: Put caller above callee in --children mode
  perf report: Do not drop last inlined frame
  perf report: Always honor callchain order for inlined nodes
  perf script: Add --inline option for debugging
  perf report: Fix off-by-one for non-activation frames
  perf report: Fix memory leak in addr2line when called by addr2inlines
  perf report: Don't crash on invalid maps in `-g srcline` mode

Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull locking fix from Thomas Gleixner:
"A fix for a state leak which was introduced in the recent rework of
futex/rtmutex interaction"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex,rt_mutex: Fix rt_mutex_cleanup_proxy_lock()

Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull kthread fix from Thomas Gleixner:
"A single fix which prevents a use after free when kthread fork fails"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kthread: Fix use-after-free if kthread fork fails

Merge tag 'trace-v4.12-rc2' of git://git./linux/kernel/git/rostedt/linux-trace

Pull ftrace fixes from Steven Rostedt:
"There's been a few memory issues found with ftrace.

  One was simply a memory leak where not all was being freed that should
  have been in releasing a file pointer on set_graph_function.

  Then Thomas found that the ftrace trampolines were marked for
  read/write as well as execute. To shrink the possible attack surface,
  he added calls to set them to ro. Which also uncovered some other
  issues with freeing module allocated memory that had its permissions
  changed.

  Kprobes had a similar issue which is fixed and a selftest was added to
  trigger that issue again"

* tag 'trace-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  x86/ftrace: Make sure that ftrace trampolines are not RWX
  x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
  selftests/ftrace: Add a testcase for many kprobe events
  kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
  ftrace: Fix memory leak in ftrace_graph_release()

x86/ftrace: Make sure that ftrace trampolines are not RWX

ftrace use module_alloc() to allocate trampoline pages. The mapping of
module_alloc() is RWX, which makes sense as the memory is written to right
after allocation. But nothing makes these pages RO after writing to them.

Add proper set_memory_rw/ro() calls to protect the trampolines after
modification.

Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1705251056410.1862@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()

With function tracing starting in early bootup and having its trampoline
pages being read only, a bug triggered with the following:

kernel BUG at arch/x86/mm/pageattr.c:189!
invalid opcode: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 4.12.0-rc2-test+ #3
Hardware name: MSI MS-7823/CSM-H87M-G43 (MS-7823), BIOS V1.6 02/22/2014
task: ffffffffb4222500 task.stack: ffffffffb4200000
RIP: 0010:change_page_attr_set_clr+0x269/0x302
RSP: 0000:ffffffffb4203c88 EFLAGS: 00010046
RAX: 0000000000000046 RBX: 0000000000000000 RCX: 00000001b6000000
RDX: ffffffffb4203d40 RSI: 0000000000000000 RDI: ffffffffb4240d60
RBP: ffffffffb4203d18 R08: 00000001b6000000 R09: 0000000000000001
R10: ffffffffb4203aa8 R11: 0000000000000003 R12: ffffffffc029b000
R13: ffffffffb4203d40 R14: 0000000000000001 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff9a639ea00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9a636b384000 CR3: 00000001ea21d000 CR4: 00000000000406b0
Call Trace:
change_page_attr_clear+0x1f/0x21
set_memory_ro+0x1e/0x20
arch_ftrace_update_trampoline+0x207/0x21c
? ftrace_caller+0x64/0x64
? 0xffffffffc029b000
ftrace_startup+0xf4/0x198
register_ftrace_function+0x26/0x3c
function_trace_init+0x5e/0x73
tracer_init+0x1e/0x23
tracing_set_tracer+0x127/0x15a
register_tracer+0x19b/0x1bc
init_function_trace+0x90/0x92
early_trace_init+0x236/0x2b3
start_kernel+0x200/0x3f5
x86_64_start_reservations+0x29/0x2b
x86_64_start_kernel+0x17c/0x18f
secondary_startup_64+0x9f/0x9f
? secondary_startup_64+0x9f/0x9f

Interrupts should not be enabled at this early in the boot process. It is
also fine to leave interrupts enabled during this time as there's only one
CPU running, and on_each_cpu() means to only run on the current CPU.

If early_boot_irqs_disabled is set, it is safe to run cpu_flush_range() with
interrupts disabled. Don't trigger a BUG_ON() in that case.

Link: http://lkml.kernel.org/r/20170526093717.0be3b849@gandalf.local.home
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

selftests/ftrace: Add a testcase for many kprobe events

Add a testcase to test kprobes via ftrace interface
with many concurrent kprobe events.

This tries to add many kprobe events (up to 256) on
kernel functions. To avoid making ftrace-based
kprobes (kprobes on fentry), it skips first N bytes
(on x86 N=5, on ppc or arm N=4) of function entry.
After that, it enables all those events, disable it,
and remove it.

Since the unoptimization buffer reclaiming will
be delayed, after removing events, it will wait
enough time.

Link: http://lkml.kernel.org/r/149577388470.11702.11832460851769204511.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

kprobes/x86: Fix to set RWX bits correctly before releasing trampoline

Fix kprobes to set(recover) RWX bits correctly on trampoline
buffer before releasing it. Releasing readonly page to
module_memfree() crash the kernel.

Without this fix, if kprobes user register a bunch of kprobes
in function body (since kprobes on function entry usually
use ftrace) and unregister it, kernel hits a BUG and crash.

Link: http://lkml.kernel.org/r/149570868652.3518.14120169373590420503.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: d0381c81c2f7 ("kprobes/x86: Set kprobes pages read-only")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

ftrace: Fix memory leak in ftrace_graph_release()

ftrace_hash is being kfree'ed in ftrace_graph_release(), however the
->buckets field is not.  This results in a memory leak that is easily
captured by kmemleak:

unreferenced object 0xffff880038afe000 (size 8192):
  comm "trace-cmd", pid 238, jiffies 4294916898 (age 9.736s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff815f561e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff8113964d>] __kmalloc+0x12d/0x1a0
    [<ffffffff810bf6d1>] alloc_ftrace_hash+0x51/0x80
    [<ffffffff810c0523>] __ftrace_graph_open.isra.39.constprop.46+0xa3/0x100
    [<ffffffff810c05e8>] ftrace_graph_open+0x68/0xa0
    [<ffffffff8114003d>] do_dentry_open.isra.1+0x1bd/0x2d0
    [<ffffffff81140df7>] vfs_open+0x47/0x60
    [<ffffffff81150f95>] path_openat+0x2a5/0x1020
    [<ffffffff81152d6a>] do_filp_open+0x8a/0xf0
    [<ffffffff811411df>] do_sys_open+0x12f/0x200
    [<ffffffff811412ce>] SyS_open+0x1e/0x20
    [<ffffffff815fa6e0>] entry_SYSCALL_64_fastpath+0x13/0x94
    [<ffffffffffffffff>] 0xffffffffffffffff

Link: http://lkml.kernel.org/r/20170525152038.7661-1-lhenriques@suse.com
Cc: stable@vger.kernel.org
Fixes: b9b0c831bed2 ("ftrace: Convert graph filter to use hash tables")
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull input layer fixes from Dmitry Torokhov:
"Just a few fixups to a couple of drivers"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elan_i2c - ignore signals when finishing updating firmware
  Input: elan_i2c - clear INT before resetting controller
  Input: atmel_mxt_ts - add T100 as a readable object
  Input: edt-ft5x06 - increase allowed data range for threshold parameter

Merge tag 'led_fixes_for_4-12-rc3' of git://git./linux/kernel/git/j.anaszewski/linux-leds

Pull LED fix from Jacek Anaszewski:
"A single LED fix for 4.12-rc3.

  leds-pca955x driver uses only i2c_smbus API and thus it should pass
  I2C_FUNC_SMBUS_BYTE_DATA flag to i2c_check_functionality"

* tag 'led_fixes_for_4-12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: pca955x: Correct I2C Functionality

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

1) Fix state pruning in bpf verifier wrt. alignment, from Daniel
    Borkmann.

2) Handle non-linear SKBs properly in SCTP ICMP parsing, from Davide
    Caratti.

3) Fix bit field definitions for rss_hash_type of descriptors in mlx5
    driver, from Jesper Brouer.

4) Defer slave->link updates until bonding is ready to do a full commit
    to the new settings, from Nithin Sujir.

5) Properly reference count ipv4 FIB metrics to avoid use after free
    situations, from Eric Dumazet and several others including Cong Wang
    and Julian Anastasov.

6) Fix races in llc_ui_bind(), from Lin Zhang.

7) Fix regression of ESP UDP encapsulation for TCP packets, from
    Steffen Klassert.

8) Fix mdio-octeon driver Kconfig deps, from Randy Dunlap.

9) Fix regression in setting DSCP on ipv6/GRE encapsulation, from Peter
    Dawson.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  ipv4: add reference counting to metrics
  net: ethernet: ax88796: don't call free_irq without request_irq first
  ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
  sctp: fix ICMP processing if skb is non-linear
  net: llc: add lock_sock in llc_ui_bind to avoid a race condition
  bonding: Don't update slave->link until ready to commit
  test_bpf: Add a couple of tests for BPF_JSGE.
  bpf: add various verifier test cases
  bpf: fix wrong exposure of map_flags into fdinfo for lpm
  bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data
  bpf: properly reset caller saved regs after helper call and ld_abs/ind
  bpf: fix incorrect pruning decision when alignment must be tracked
  arp: fixed -Wuninitialized compiler warning
  tcp: avoid fastopen API to be used on AF_UNSPEC
  net: move somaxconn init from sysctl code
  net: fix potential null pointer dereference
  geneve: fix fill_info when using collect_metadata
  virtio-net: enable TSO/checksum offloads for Q-in-Q vlans
  be2net: Fix offload features for Q-in-Q packets
  vlan: Fix tcp checksum offloads in Q-in-Q vlans
  ...

Merge tag 'xfs-4.12-fixes-2' of git://git./fs/xfs/xfs-linux

Pull XFS fixes from Darrick Wong:
"A few miscellaneous bug fixes & cleanups:

   - Fix indlen block reservation accounting bug when splitting delalloc
     extent

   - Fix warnings about unused variables that appeared in -rc1.

   - Don't spew errors when bmapping a local format directory

   - Fix an off-by-one error in a delalloc eof assertion

   - Make fsmap only return inode information for CAP_SYS_ADMIN

   - Fix a potential mount time deadlock recovering cow extents

   - Fix unaligned memory access in _btree_visit_blocks

   - Fix various SEEK_HOLE/SEEK_DATA bugs"

* tag 'xfs-4.12-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: Move handling of missing page into one place in xfs_find_get_desired_pgoff()
  xfs: Fix off-by-in in loop termination in xfs_find_get_desired_pgoff()
  xfs: Fix missed holes in SEEK_HOLE implementation
  xfs: fix off-by-one on max nr_pages in xfs_find_get_desired_pgoff()
  xfs: fix unaligned access in xfs_btree_visit_blocks
  xfs: avoid mount-time deadlock in CoW extent recovery
  xfs: only return detailed fsmap info if the caller has CAP_SYS_ADMIN
  xfs: bad assertion for delalloc an extent that start at i_size
  xfs: fix warnings about unused stack variables
  xfs: BMAPX shouldn't barf on inline-format directories
  xfs: fix indlen accounting error on partial delalloc conversion

ipv4: add reference counting to metrics

Andrey Konovalov reported crashes in ipv4_mtu()

I could reproduce the issue with KASAN kernels, between
10.246.7.151 and 10.246.7.152 :

1) 20 concurrent netperf -t TCP_RR -H 10.246.7.152 -l 1000 &

2) At the same time run following loop :
while :
do
ip ro add 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
ip ro del 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
done

Cong Wang attempted to add back rt->fi in commit
82486aa6f1b9 ("ipv4: restore rt->fi for reference counting")
but this proved to add some issues that were complex to solve.

Instead, I suggested to add a refcount to the metrics themselves,
being a standalone object (in particular, no reference to other objects)

I tried to make this patch as small as possible to ease its backport,
instead of being super clean. Note that we believe that only ipv4 dst
need to take care of the metric refcount. But if this is wrong,
this patch adds the basic infrastructure to extend this to other
families.

Many thanks to Julian Anastasov for reviewing this patch, and Cong Wang
for his efforts on this problem.

Fixes: 2860583fe840 ("ipv4: Kill rt->fi")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ax88796: don't call free_irq without request_irq first

The function ax_init_dev (which is called only from the driver's .probe
function) calls free_irq in the error path without having requested the
irq in the first place. So drop the free_irq call in the error path.

Fixes: 825a2ff1896e ("AX88796 network driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets

This fix addresses two problems in the way the DSCP field is formulated
on the encapsulating header of IPv6 tunnels.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195661

1) The IPv6 tunneling code was manipulating the DSCP field of the
encapsulating packet using the 32b flowlabel. Since the flowlabel is
only the lower 20b it was incorrect to assume that the upper 12b
containing the DSCP and ECN fields would remain intact when formulating
the encapsulating header. This fix handles the 'inherit' and
'fixed-value' DSCP cases explicitly using the extant dsfield u8 variable.

2) The use of INET_ECN_encapsulate(0, dsfield) in ip6_tnl_xmit was
incorrect and resulted in the DSCP value always being set to 0.

Commit 90427ef5d2a4 ("ipv6: fix flow labels when the traffic class
is non-0") caused the regression by masking out the flowlabel
which exposed the incorrect handling of the DSCP portion of the
flowlabel in ip6_tunnel and ip6_gre.

Fixes: 90427ef5d2a4 ("ipv6: fix flow labels when the traffic class is non-0")
Signed-off-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix ICMP processing if skb is non-linear

sometimes ICMP replies to INIT chunks are ignored by the client, even if
the encapsulated SCTP headers match an open socket. This happens when the
ICMP packet is carried by a paged skb: use skb_header_pointer() to read
packet contents beyond the SCTP header, so that chunk header and initiate
tag are validated correctly.

v2:
- don't use skb_header_pointer() to read the transport header, since
icmp_socket_deliver() already puts these 8 bytes in the linear area.
- change commit message to make specific reference to INIT chunks.

Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: llc: add lock_sock in llc_ui_bind to avoid a race condition

There is a race condition in llc_ui_bind if two or more processes/threads
try to bind a same socket.

If more processes/threads bind a same socket success that will lead to
two problems, one is this action is not what we expected, another is
will lead to kernel in unstable status or oops(in my simple test case,
cause llc2.ko can't unload).

The current code is test SOCK_ZAPPED bit to avoid a process to
bind a same socket twice but that is can't avoid more processes/threads
try to bind a same socket at the same time.

So, add lock_sock in llc_ui_bind like others, such as llc_ui_connect.

Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-linus' of git://git.kernel.dk/linux-block

Pull block fixes from Jens Axboe:
"A collection of fixes that should go into this series. This contains:

   - A set of NVMe fixes, pulled from Christoph. This includes a set of
     fixes for the fiber channel bits from James Smart, rdma queue depth
     fix from Marta, controller removal fixes from Ming, and some more
     APST quirk updates from Andy.

   - A blk-mq debugfs fix from Bart, fixing a problem with the
     untangling of the sysfs and debugfs blk-mq bits that was added in
     this series.

   - Error code fix in add_partition() from Dan.

   - A small series of fixes for the new blk-throttle code from Shaohua"

* 'for-linus' of git://git.kernel.dk/linux-block: (21 commits)
  blk-mq: Only register debugfs attributes for blk-mq queues
  nvme: Quirk APST on Intel 600P/P3100 devices
  nvme: only setup block integrity if supported by the driver
  nvme: replace is_flags field in nvme_ctrl_ops with a flags field
  nvme-pci: consistencly use ctrl->device for logging
  partitions/msdos: FreeBSD UFS2 file systems are not recognized
  block: fix an error code in add_partition()
  blk-throttle: force user to configure all settings for io.low
  blk-throttle: respect 0 bps/iops settings for io.low
  blk-throttle: output some debug info in trace
  blk-throttle: add hierarchy support for latency target and idle time
  nvme_fc: remove extra controller reference taken on reconnect
  nvme_fc: correct nvme status set on abort
  nvme_fc: set logging level on resets/deletes
  nvme_fc: revise comment on teardown
  nvme_fc: Support ctrl_loss_tmo
  nvme_fc: get rid of local reconnect_delay
  blk-mq: remove blk_mq_abort_requeue_list()
  nvme: avoid to use blk_mq_abort_requeue_list()
  nvme: use blk_mq_start_hw_queues() in nvme_kill_queues()
  ...

Merge tag 'pci-v4.12-fixes-1' of git://git./linux/kernel/git/helgaas/pci

Pull PCI fixes from Bjorn Helgaas:

- fix PCI_ENDPOINT build error (merged for v4.12)

- fix Switchtec driver (merged for v4.12)

- fix imx6 config read timeouts, fallout from changing to non-postable
   reads

- add PM "needs_resume" flag for i915 suspend issue

* tag 'pci-v4.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI/PM: Add needs_resume flag to avoid suspend complete optimization
  PCI: imx6: Fix config read timeout handling
  switchtec: Fix minor bug with partition ID register
  switchtec: Use new cdev_device_add() helper function
  PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA

Merge tag 'ceph-for-4.12-rc3' of git://github.com/ceph/ceph-client

Pul ceph fixes from Ilya Dryomov:
"A bunch of make W=1 and static checker fixups, a RECONNECT_SEQ
  messenger patch from Zheng and Luis' fallocate fix"

* tag 'ceph-for-4.12-rc3' of git://github.com/ceph/ceph-client:
  ceph: check that the new inode size is within limits in ceph_fallocate()
  libceph: cleanup old messages according to reconnect seq
  libceph: NULL deref on crush_decode() error path
  libceph: fix error handling in process_one_ticket()
  libceph: validate blob_struct_v in process_one_ticket()
  libceph: drop version variable from ceph_monmap_decode()
  libceph: make ceph_msg_data_advance() return void
  libceph: use kbasename() and kill ceph_file_part()

Merge tag 'mmc-v4.12-rc2' of git://git./linux/kernel/git/ulfh/mmc

Pull MMC fixes from Ulf Hansson:
"This contains fixes to make the WiFi work again for the ARM64 Hikey
  board.

  Together with a couple of DTS updates for the Hikey board we have also
  extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
  property, as that was required to enable a graceful power off sequence
  for the WiFi chip"

* tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  arm64: dts: hikey: Fix WiFi support
  arm64: dts: hi6220: Move board data from the dwmmc nodes to hikey dts
  arm64: dts: hikey: Add the SYS_5V and the VDD_3V3 regulators
  arm64: dts: hi6220: Move the fixed_5v_hub regulator to the hikey dts
  arm64: dts: hikey: Add clock for the pmic mfd
  mfd: dts: hi655x: Add clock binding for the pmic
  mmc: pwrseq_simple: Parse DTS for the power-off-delay-us property
  mmc: dt: pwrseq-simple: Invent power-off-delay-us

Merge tag 'sound-4.12-rc3' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"This contains a few HD-audio device-specific quirks and an endianess
  fix for USB-audio, as well as the update of quirk model list document.
  All fixes are small and trivial.

  The document update could have been postponed, but it's a good thing
  for user and has absolutely zero risk of breakage, so included here"

* tag 'sound-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - apply STAC_9200_DELL_M22 quirk for Dell Latitude D430
  ALSA: hda - Update the list of quirk models
  ALSA: hda - Provide dual-codecs model option for a few Realtek codecs
  ALSA: hda - Apply dual-codec quirk for MSI Z270-Gaming mobo
  ALSA: hda - No loopback on ALC299 codec
  ALSA: usb-audio: fix Amanero Combo384 quirk on big-endian hosts

Merge tag 'drm-fixes-for-v4.12-rc3' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
"Not a whole lot happening here, a set of amdgpu fixes and one core
  deadlock fix, and some misc drivers fixes"

* tag 'drm-fixes-for-v4.12-rc3' of git://people.freedesktop.org/~airlied/linux:
  drm/amdgpu: fix null point error when rmmod amdgpu.
  drm/amd/powerplay: fix a signedness bugs
  drm/amdgpu: fix NULL pointer panic of emit_gds_switch
  drm/radeon: Unbreak HPD handling for r600+
  drm/amd/powerplay/smu7: disable mclk switching for high refresh rates
  drm/amd/powerplay/smu7: add vblank check for mclk switching (v2)
  drm/radeon/ci: disable mclk switching for high refresh rates (v2)
  drm/amdgpu/ci: disable mclk switching for high refresh rates (v2)
  drm/amdgpu: fix fundamental suspend/resume issue
  drm/gma500/psb: Actually use VBT mode when it is found
  drm: Fix deadlock retry loop in page_flip_ioctl
  drm: qxl: Delay entering atomic context during cursor update
  drm/radeon: Fix oops upon driver load on PowerXpress laptops

PCI/msi: fix the pci_alloc_irq_vectors_affinity stub

We need to return an error for any call that asks for MSI / MSI-X
vectors only, so that non-trivial fallback logic can work properly.

Also valid dev->irq and use the "correct" errno value based on feedback
from Linus.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Fixes: aff17164 ("PCI: Provide sensible IRQ vector alloc/free routines")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'nvme-4.12' of git://git.infradead.org/nvme into for-linus

Christoph writes:

"A couple of fixes for the next rc on the nvme front. Various FC fixes
from James, controller removal fixes from Ming (including a block layer
patch), a APST related device quirk from Andy, a RDMA fix for small
queue depth device from Marta, as well as fixes for the lack of
metadata support in non-PCIe drivers and the printk logging format from
me."

drm/i915: Keep the forcewake timer alive for 1ms past the most recent use

Currently the timer is armed for 1ms after the first use and is killed
immediately, dropping the forcewake as early as possible. However, for
very frequent operations the forcewake dance has a large impact on
latency and keeping the timer alive until we are idle is preferred. To
achieve this, if we call intel_uncore_forcewake_get whilst the timer is
alive (repeated use), then set a flag to restart the timer on expiry
rather than drop the forcewake usage count. The timer is racy, the
consequence of the race is to expire the timer earlier than is now
desired but does not impact on correct behaviour. The offset the race
slightly, we set the active flag again on intel_uncore_forcewake_put.

The effect should be to reduce the jitter of reacquiring the fw every
1ms on a busy system. However, the cost is to keep the timer alive for
an extra 1ms on a nearly idle system. We chose to incur the jitter
previously to keep the timer off for as much as possible.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526132209.14640-1-chris@chris-wilson.co.uk

blk-mq: Only register debugfs attributes for blk-mq queues

The code in blk-mq-debugfs.c assumes that it is working on a blk-mq
queue and is not intended to work on a blk-sq queue. Hence only
register blk-mq debugfs attributes for blk-mq queues.

Fixes: commit 9c1051aacde8 ("blk-mq: untangle debugfs and sysfs")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

drm/i915/guc: capture GuC logs if FW fails to load

We're currently deleting the GuC logs if the FW fails to load, but those
are still useful to understand why the loading failed. Keeping the
object around allows us to access them after driver load is completed.

v2: keep the object around instead of using kernel memory (chris)
    don't store the logs in the gpu_error struct (Chris)
    add a check on guc_log_level to avoid snapshotting empty logs

v3: use separate debugfs for error log (Chris)

v4: rebased

v5: clean up obj selection, move err_load inside guc_log, move err_load
    cleanup, rename functions (Michal)

v6: move obj back to intel_guc, move functions to intel_uc.c, don't
    clear obj on new GuC load, free object only if enable_guc_loading
    is set (Michal)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495475428-19295-1-git-send-email-daniele.ceraolospurio@intel.com
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Tested-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/guc: Introduce buffer based cmd transport

Buffer based command transport can replace MMIO based mechanism.
It may be used to perform host-2-guc and guc-to-host communication.

Portions of this patch are based on work by:
Michel Thierry <michel.thierry@intel.com>
Robert Beckett <robert.beckett@intel.com>
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>

v2: use gem_object_pin_map (Chris)
    don't use DEBUG_RATELIMITED (Chris)
    don't track action stats (Chris)
    simplify next fence (Chris)
    use READ_ONCE (Chris)
    move blob allocation to new function (Chris)

v3: use static owner id (Daniele)
v4: but keep channel initialization generic (Daniele)
    and introduce owner_sub_id (Daniele)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526111326.87280-3-michal.wajdeczko@intel.com

drm/i915/guc: Disable send function on fini

In earlier patch 789a625 we were enabling send function only
after successful init. For completeness, we should make sure
that we disable it on fini.

v2: don't group steps by submission flag (Chris)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526111326.87280-2-michal.wajdeczko@intel.com

drm: Add definition for eDP backlight frequency

This patch adds the following definition
- Bit mask for EDP_PWMGEN_BIT_COUNT and min/max cap
register which only use bit 0:4
- Base frequency (27 MHz) for backlight PWM frequency
generator.

Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523223805.46372-5-puthik@chromium.org

drm/i915: Drop AUX backlight enable check for backlight control

There are some panel that
(1) does not support display backlight enable via AUX
(2) support display backlight adjustment via AUX
(3) support display backlight enable via eDP BL_ENABLE pin

The current driver required that (1) must be support to enable (2).
This patch drops that requirement.

Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523223805.46372-2-puthik@chromium.org

x86/timers: Move simple_udelay_calibration past init_hypervisor_platform

This ensures that adjustments to x86_platform done by the hypervisor
setup is already respected by this simple calibration.

The current user of this, introduced by 1b5aeebf3a92 ("x86/earlyprintk:
Add support for earlyprintk via USB3 debug port"), comes much later
into play.

Fixes: dd759d93f4dd ("x86/timers: Add simple udelay calibration")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: http://lkml.kernel.org/r/5e89fe60-aab3-2c1c-aba8-32f8ad376189@siemens.com

nvme: Quirk APST on Intel 600P/P3100 devices

They have known firmware bugs. A fix is apparently in the works --
once fixed firmware is available, someone from Intel (Hi, Keith!)
can adjust the quirk accordingly.

Cc: stable@vger.kernel.org # v4.11
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>

nvme: only setup block integrity if supported by the driver

Currently only the PCIe driver supports metadata, so we should not claim
integrity support for the other drivers. This prevents nasty crashes
with targets that advertise metadata support on fabrics.

Also use the opportunity to factor out some code into a separate helper
that isn't even compiled if CONFIG_BLK_DEV_INTEGRITY is disabled.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>

nvme: replace is_flags field in nvme_ctrl_ops with a flags field

So that we can have more flags for transport-specific behavior.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>

nvme-pci: consistencly use ctrl->device for logging

This is what most of the code already does and gives much more useful
prefixes than the device embedded in the pci_dev.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>

Merge branch 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes

A bunch of bug fixes:
- Fix display flickering on some chips at high refresh rates
- suspend/resume fix
- hotplug fix
- a couple of segfault fixes for certain cases

* 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux:
  drm/amdgpu: fix null point error when rmmod amdgpu.
  drm/amd/powerplay: fix a signedness bugs
  drm/amdgpu: fix NULL pointer panic of emit_gds_switch
  drm/radeon: Unbreak HPD handling for r600+
  drm/amd/powerplay/smu7: disable mclk switching for high refresh rates
  drm/amd/powerplay/smu7: add vblank check for mclk switching (v2)
  drm/radeon/ci: disable mclk switching for high refresh rates (v2)
  drm/amdgpu/ci: disable mclk switching for high refresh rates (v2)
  drm/amdgpu: fix fundamental suspend/resume issue

Merge tag 'drm-misc-fixes-2017-05-25' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes

Core Changes:
- Don't drop vblank reference more than once in cases of ww retry (Daniel)

Driver Changes:
- radeon: Fix oops during radeon probe trying to reference wrong device (Lukas)
- qxl: Avoid sleeping while in atomic context on cursor update (Gabriel)
- gma500: Use VBT mode instead of pre-programmed mode for LVDS (Patrik)

Cc: Lukas Wunner <lukas@wunner.de>
Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
* tag 'drm-misc-fixes-2017-05-25' of git://anongit.freedesktop.org/git/drm-misc:
  drm/gma500/psb: Actually use VBT mode when it is found
  drm: Fix deadlock retry loop in page_flip_ioctl
  drm: qxl: Delay entering atomic context during cursor update
  drm/radeon: Fix oops upon driver load on PowerXpress laptops

drm/i915: Consolidate #ifdef CONFIG_INTEL_IOMMU

We depend on intel_iommu_gfx_mapped for various workarounds, but that is
only available under an #ifdef CONFIG_INTEL_IOMMU. Refactor all the
cut-and-paste ifdefs to a common routine.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170525121612.2190-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Only GGTT vma may be pinned and prevent shrinking

As only GGTT vma may be permanently pinned and are always at the head of
the object's vma list, as soon as we seen a ppGTT vma we can stop
searching for any_vma_pinned().

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170525072528.11185-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

bonding: Don't update slave->link until ready to commit

In the loadbalance arp monitoring scheme, when a slave link change is
detected, the slave->link is immediately updated and slave_state_changed
is set. Later down the function, the rtnl_lock is acquired and the
changes are committed, updating the bond link state.

However, the acquisition of the rtnl_lock can fail. The next time the
monitor runs, since slave->link is already updated, it determines that
link is unchanged. This results in the bond link state permanently out
of sync with the slave link.

This patch modifies bond_loadbalance_arp_mon() to handle link changes
identical to bond_ab_arp_{inspect/commit}(). The new link state is
maintained in slave->new_link until we're ready to commit at which point
it's copied into slave->link.

NOTE: miimon_{inspect/commit}() has a more complex state machine
requiring the use of the bond_{propose,commit}_link_state() functions
which maintains the intermediate state in slave->link_new_state. The arp
monitors don't require that.

Testing: This bug is very easy to reproduce with the following steps.
1. In a loop, toggle a slave link of a bond slave interface.
2. In a separate loop, do ifconfig up/down of an unrelated interface to
create contention for rtnl_lock.
Within a few iterations, the bond link goes out of sync with the slave
link.

Signed-off-by: Nithin Nayak Sujir <nsujir@tintri.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

test_bpf: Add a couple of tests for BPF_JSGE.

Some JITs can optimize comparisons with zero. Add a couple of
BPF_JSGE tests against immediate zero.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bpf-fixes'

Daniel Borkmann says:

====================
Various BPF fixes

Follow-up to fix incorrect pruning when alignment tracking is
in use and to properly clear regs after call to not leave stale
data behind, also a fix that adds bpf_clone_redirect to the
bpf_helper_changes_pkt_data helper and exposes correct map_flags
for lpm map into fdinfo. For details, please see individual
patches.

v1 -> v2:
  - Reworked first patch so that env->strict_alignment is the
    final indicator on whether we have to deal with strict
    alignment rather than having CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
    checks on various locations, so only checking env->strict_alignment
    is sufficient after that. Thanks for spotting, Dave!
  - Added patch 3 and 4.
  - Rest as is.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: add various verifier test cases

This patch adds various verifier test cases:

1) A test case for the pruning issue when tracking alignment
   is used.
2) Various PTR_TO_MAP_VALUE_OR_NULL tests to make sure pointer
   arithmetic turns such register into UNKNOWN_VALUE type.
3) Test cases for the special treatment of LD_ABS/LD_IND to
   make sure verifier doesn't break calling convention here.
   Latter is needed, since f.e. arm64 JIT uses r1 - r5 for
   storing temporary data, so they really must be marked as
   NOT_INIT.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: fix wrong exposure of map_flags into fdinfo for lpm

trie_alloc() always needs to have BPF_F_NO_PREALLOC passed in via
attr->map_flags, since it does not support preallocation yet. We
check the flag, but we never copy the flag into trie->map.map_flags,
which is later on exposed into fdinfo and used by loaders such as
iproute2. Latter uses this in bpf_map_selfcheck_pinned() to test
whether a pinned map has the same spec as the one from the BPF obj
file and if not, bails out, which is currently the case for lpm
since it exposes always 0 as flags.

Also copy over flags in array_map_alloc() and stack_map_alloc().
They always have to be 0 right now, but we should make sure to not
miss to copy them over at a later point in time when we add actual
flags for them to use.

Fixes: b95a5c4db09b ("bpf: add a longest prefix match trie map implementation")
Reported-by: Jarno Rajahalme <jarno@covalent.io>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data

The bpf_clone_redirect() still needs to be listed in
bpf_helper_changes_pkt_data() since we call into
bpf_try_make_head_writable() from there, thus we need
to invalidate prior pkt regs as well.

Fixes: 36bbef52c7eb ("bpf: direct packet write and access for helpers for clsact progs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: properly reset caller saved regs after helper call and ld_abs/ind

Currently, after performing helper calls, we clear all caller saved
registers, that is r0 - r5 and fill r0 depending on struct bpf_func_proto
specification. The way we reset these regs can affect pruning decisions
in later paths, since we only reset register's imm to 0 and type to
NOT_INIT. However, we leave out clearing of other variables such as id,
min_value, max_value, etc, which can later on lead to pruning mismatches
due to stale data.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: fix incorrect pruning decision when alignment must be tracked

Currently, when we enforce alignment tracking on direct packet access,
the verifier lets the following program pass despite doing a packet
write with unaligned access:

  0: (61) r2 = *(u32 *)(r1 +76)
  1: (61) r3 = *(u32 *)(r1 +80)
  2: (61) r7 = *(u32 *)(r1 +8)
  3: (bf) r0 = r2
  4: (07) r0 += 14
  5: (25) if r7 > 0x1 goto pc+4
   R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
   R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
  6: (2d) if r0 > r3 goto pc+1
   R0=pkt(id=0,off=14,r=14) R1=ctx R2=pkt(id=0,off=0,r=14)
   R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
  7: (63) *(u32 *)(r0 -4) = r0
  8: (b7) r0 = 0
  9: (95) exit

  from 6 to 8:
   R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
   R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
  8: (b7) r0 = 0
  9: (95) exit

  from 5 to 10:
   R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
   R3=pkt_end R7=inv,min_value=2 R10=fp
  10: (07) r0 += 1
  11: (05) goto pc-6
  6: safe                           <----- here, wrongly found safe
  processed 15 insns

However, if we enforce a pruning mismatch by adding state into r8
which is then being mismatched in states_equal(), we find that for
the otherwise same program, the verifier detects a misaligned packet
access when actually walking that path:

  0: (61) r2 = *(u32 *)(r1 +76)
  1: (61) r3 = *(u32 *)(r1 +80)
  2: (61) r7 = *(u32 *)(r1 +8)
  3: (b7) r8 = 1
  4: (bf) r0 = r2
  5: (07) r0 += 14
  6: (25) if r7 > 0x1 goto pc+4
   R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
   R3=pkt_end R7=inv,min_value=0,max_value=1
   R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
  7: (2d) if r0 > r3 goto pc+1
   R0=pkt(id=0,off=14,r=14) R1=ctx R2=pkt(id=0,off=0,r=14)
   R3=pkt_end R7=inv,min_value=0,max_value=1
   R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
  8: (63) *(u32 *)(r0 -4) = r0
  9: (b7) r0 = 0
  10: (95) exit

  from 7 to 9:
   R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
   R3=pkt_end R7=inv,min_value=0,max_value=1
   R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
  9: (b7) r0 = 0
  10: (95) exit

  from 6 to 11:
   R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
   R3=pkt_end R7=inv,min_value=2
   R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
  11: (07) r0 += 1
  12: (b7) r8 = 0
  13: (05) goto pc-7                <----- mismatch due to r8
  7: (2d) if r0 > r3 goto pc+1
   R0=pkt(id=0,off=15,r=15) R1=ctx R2=pkt(id=0,off=0,r=15)
   R3=pkt_end R7=inv,min_value=2
   R8=imm0,min_value=0,max_value=0,min_align=2147483648 R10=fp
  8: (63) *(u32 *)(r0 -4) = r0
  misaligned packet access off 2+15+-4 size 4

The reason why we fail to see it in states_equal() is that the
third test in compare_ptrs_to_packet() ...

  if (old->off <= cur->off &&
      old->off >= old->range && cur->off >= cur->range)
          return true;

... will let the above pass. The situation we run into is that
old->off <= cur->off (14 <= 15), meaning that prior walked paths
went with smaller offset, which was later used in the packet
access after successful packet range check and found to be safe
already.

For example: Given is R0=pkt(id=0,off=0,r=0). Adding offset 14
as in above program to it, results in R0=pkt(id=0,off=14,r=0)
before the packet range test. Now, testing this against R3=pkt_end
with 'if r0 > r3 goto out' will transform R0 into R0=pkt(id=0,off=14,r=14)
for the case when we're within bounds. A write into the packet
at offset *(u32 *)(r0 -4), that is, 2 + 14 -4, is valid and
aligned (2 is for NET_IP_ALIGN). After processing this with
all fall-through paths, we later on check paths from branches.
When the above skb->mark test is true, then we jump near the
end of the program, perform r0 += 1, and jump back to the
'if r0 > r3 goto out' test we've visited earlier already. This
time, R0 is of type R0=pkt(id=0,off=15,r=0), and we'll prune
that part because this time we'll have a larger safe packet
range, and we already found that with off=14 all further insn
were already safe, so it's safe as well with a larger off.
However, the problem is that the subsequent write into the packet
with 2 + 15 -4 is then unaligned, and not caught by the alignment
tracking. Note that min_align, aux_off, and aux_off_align were
all 0 in this example.

Since we cannot tell at this time what kind of packet access was
performed in the prior walk and what minimal requirements it has
(we might do so in the future, but that requires more complexity),
fix it to disable this pruning case for strict alignment for now,
and let the verifier do check such paths instead. With that applied,
the test cases pass and reject the program due to misalignment.

Fixes: d1174416747d ("bpf: Track alignment of register values in the verifier.")
Reference: http://patchwork.ozlabs.org/patch/761909/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

arp: fixed -Wuninitialized compiler warning

Commit 7d472a59c0e5ec117220a05de6b370447fb6cb66 ("arp: always override
existing neigh entries with gratuitous ARP") introduced a compiler
warning:

net/ipv4/arp.c:880:35: warning: 'addr_type' may be used uninitialized in
this function [-Wmaybe-uninitialized]

While the code logic seems to be correct and doesn't allow the variable
to be used uninitialized, and the warning is not consistently
reproducible, it's still worth fixing it for other people not to waste
time looking at the warning in case it pops up in the build environment.
Yes, compiler is probably at fault, but we will need to accommodate.

Fixes: 7d472a59c0e5 ("arp: always override existing neigh entries with gratuitous ARP")
Signed-off-by: Ihar Hrachyshka <ihrachys@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: avoid fastopen API to be used on AF_UNSPEC

Fastopen API should be used to perform fastopen operations on the TCP
socket. It does not make sense to use fastopen API to perform disconnect
by calling it with AF_UNSPEC. The fastopen data path is also prone to
race conditions and bugs when using with AF_UNSPEC.

One issue reported and analyzed by Vegard Nossum is as follows:
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Thread A:                            Thread B:
------------------------------------------------------------------------
sendto()
- tcp_sendmsg()
     - sk_stream_memory_free() = 0
         - goto wait_for_sndbuf
     - sk_stream_wait_memory()
        - sk_wait_event() // sleep
          |                          sendto(flags=MSG_FASTOPEN, dest_addr=AF_UNSPEC)
  |                           - tcp_sendmsg()
  |                              - tcp_sendmsg_fastopen()
  |                                 - __inet_stream_connect()
  |                                    - tcp_disconnect() //because of AF_UNSPEC
  |                                       - tcp_transmit_skb()// send RST
  |                                    - return 0; // no reconnect!
  |                           - sk_stream_wait_connect()
  |                                 - sock_error()
  |                                    - xchg(&sk->sk_err, 0)
  |                                    - return -ECONNRESET
- ... // wake up, see sk->sk_err == 0
    - skb_entail() on TCP_CLOSE socket

If the connection is reopened then we will send a brand new SYN packet
after thread A has already queued a buffer. At this point I think the
socket internal state (sequence numbers etc.) becomes messed up.

When the new connection is closed, the FIN-ACK is rejected because the
sequence number is outside the window. The other side tries to
retransmit,
but __tcp_retransmit_skb() calls tcp_trim_head() on an empty skb which
corrupts the skb data length and hits a BUG() in copy_and_csum_bits().
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Hence, this patch adds a check for AF_UNSPEC in the fastopen data path
and return EOPNOTSUPP to user if such case happens.

Fixes: cf60af03ca4e7 ("tcp: Fast Open client - sendmsg(MSG_FASTOPEN)")
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: move somaxconn init from sysctl code

The default value for somaxconn is set in sysctl_core_net_init(), but this
function is not called when kernel is configured without CONFIG_SYSCTL.

This results in the kernel not being able to accept TCP connections,
because the backlog has zero size. Usually, the user ends up with:
"TCP: request_sock_TCP: Possible SYN flooding on port 7. Dropping request. Check SNMP counters."
If SYN cookies are not enabled the connection is rejected.

Before ef547f2ac16 (tcp: remove max_qlen_log), the effects were less
severe, because the backlog was always at least eight slots long.

Signed-off-by: Roman Kapl <roman.kapl@sysgo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Input: elan_i2c - ignore signals when finishing updating firmware

Use wait_for_completion_timeout() instead of
wait_for_completion_interruptible_timeout() to avoid stray signals ruining
firmware update. Our timeout is only 300 msec so we are fine simply letting
it expire in case device misbehaves.

Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Input: elan_i2c - clear INT before resetting controller

Some old touchpad FWs need to have interrupt cleared before issuing reset
command after updating firmware. We clear interrupt by attempting to read
full report from the controller, and discarding any data read.

Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

net: fix potential null pointer dereference

Add null check to avoid a potential null pointer dereference.

Addresses-Coverity-ID: 1408831
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drm/amdgpu: fix null point error when rmmod amdgpu.

this bug happened when amdgpu load failed.

[   75.740951] BUG: unable to handle kernel paging request at 00000000000031c0
[   75.748167] IP: [<ffffffffa064a0e0>] amdgpu_fbdev_restore_mode+0x20/0x60 [amdgpu]
[   75.755774] PGD 0

[   75.759185] Oops: 0000 [#1] SMP
[   75.762408] Modules linked in: amdgpu(OE-) ttm(OE) drm_kms_helper(OE) drm(OE) i2c_algo_bit(E) fb_sys_fops(E) syscopyarea(E) sysfillrect(E) sysimgblt(E) rpcsec_gss_krb5(E) nfsv4(E) nfs(E) fscache(E) eeepc_wmi(E) asus_wmi(E) sparse_keymap(E) intel_rapl(E) snd_hda_codec_hdmi(E) snd_hda_codec_realtek(E) snd_hda_codec_generic(E) snd_hda_intel(E) snd_hda_codec(E) snd_hda_core(E) x86_pkg_temp_thermal(E) intel_powerclamp(E) snd_hwdep(E) snd_pcm(E) snd_seq_midi(E) coretemp(E) kvm_intel(E) snd_seq_midi_event(E) snd_rawmidi(E) kvm(E) snd_seq(E) joydev(E) snd_seq_device(E) snd_timer(E) irqbypass(E) crct10dif_pclmul(E) crc32_pclmul(E) mei_me(E) ghash_clmulni_intel(E) snd(E) aesni_intel(E) mei(E) soundcore(E) aes_x86_64(E) shpchp(E) serio_raw(E) lrw(E) acpi_pad(E) gf128mul(E) glue_helper(E) ablk_helper(E) mac_hid(E)
[   75.835574]  cryptd(E) parport_pc(E) ppdev(E) lp(E) nfsd(E) parport(E) auth_rpcgss(E) nfs_acl(E) lockd(E) grace(E) sunrpc(E) autofs4(E) hid_generic(E) usbhid(E) mxm_wmi(E) psmouse(E) e1000e(E) ptp(E) pps_core(E) ahci(E) libahci(E) wmi(E) video(E) i2c_hid(E) hid(E)
[   75.858489] CPU: 5 PID: 1603 Comm: rmmod Tainted: G           OE   4.9.0-custom #2
[   75.866183] Hardware name: System manufacturer System Product Name/Z170-A, BIOS 0901 08/31/2015
[   75.875050] task: ffff88045d1bbb80 task.stack: ffffc90002de4000
[   75.881094] RIP: 0010:[<ffffffffa064a0e0>]  [<ffffffffa064a0e0>] amdgpu_fbdev_restore_mode+0x20/0x60 [amdgpu]
[   75.891238] RSP: 0018:ffffc90002de7d48  EFLAGS: 00010286
[   75.896648] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000001
[   75.903933] RDX: 0000000000000000 RSI: ffff88045d1bbb80 RDI: 0000000000000286
[   75.911183] RBP: ffffc90002de7d50 R08: 0000000000000502 R09: 0000000000000004
[   75.918449] R10: 0000000000000000 R11: 0000000000000001 R12: ffff880464bf0000
[   75.925675] R13: ffffffffa0853000 R14: 0000000000000000 R15: 0000564e44f88210
[   75.932980] FS:  00007f13d5400700(0000) GS:ffff880476540000(0000) knlGS:0000000000000000
[   75.941238] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   75.947088] CR2: 00000000000031c0 CR3: 000000045fd0b000 CR4: 00000000003406e0
[   75.954332] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   75.961566] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   75.968834] Stack:
[   75.970881]  ffff880464bf0000 ffffc90002de7d60 ffffffffa0636592 ffffc90002de7d80
[   75.978454]  ffffffffa059015f ffff880464bf0000 ffff880464bf0000 ffffc90002de7da8
[   75.986076]  ffffffffa0595216 ffff880464bf0000 ffff880460f4d000 ffffffffa0853000
[   75.993692] Call Trace:
[   75.996177]  [<ffffffffa0636592>] amdgpu_driver_lastclose_kms+0x12/0x20 [amdgpu]
[   76.003700]  [<ffffffffa059015f>] drm_lastclose+0x2f/0xd0 [drm]
[   76.009777]  [<ffffffffa0595216>] drm_dev_unregister+0x16/0xd0 [drm]
[   76.016255]  [<ffffffffa0595944>] drm_put_dev+0x34/0x70 [drm]
[   76.022139]  [<ffffffffa062f365>] amdgpu_pci_remove+0x15/0x20 [amdgpu]
[   76.028800]  [<ffffffff81416499>] pci_device_remove+0x39/0xc0
[   76.034661]  [<ffffffff81531caa>] __device_release_driver+0x9a/0x140
[   76.041121]  [<ffffffff81531e58>] driver_detach+0xb8/0xc0
[   76.046575]  [<ffffffff81530c95>] bus_remove_driver+0x55/0xd0
[   76.052401]  [<ffffffff815325fc>] driver_unregister+0x2c/0x50
[   76.058244]  [<ffffffff81416289>] pci_unregister_driver+0x29/0x90
[   76.064466]  [<ffffffffa0596c5e>] drm_pci_exit+0x9e/0xb0 [drm]
[   76.070507]  [<ffffffffa0796d71>] amdgpu_exit+0x1c/0x32 [amdgpu]
[   76.076609]  [<ffffffff81104810>] SyS_delete_module+0x1a0/0x200
[   76.082627]  [<ffffffff810e2b1a>] ? rcu_eqs_enter.isra.36+0x4a/0x50
[   76.089001]  [<ffffffff8100392e>] do_syscall_64+0x6e/0x180
[   76.094583]  [<ffffffff817e1d2f>] entry_SYSCALL64_slow_path+0x25/0x25
[   76.101114] Code: 94 c0 c3 31 c0 5d c3 0f 1f 40 00 0f 1f 44 00 00 55 31 c0 48 89 e5 53 48 89 fb 48 c7 c7 1d 21 84 a0 e8 ab 77 b3 e0 e8 fc 8b d7 e0 <48> 8b bb c0 31 00 00 48 85 ff 74 09 e8 ff eb fc ff 85 c0 75 03
[   76.121432] RIP  [<ffffffffa064a0e0>] amdgpu_fbdev_restore_mode+0x20/0x60 [amdgpu]

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

geneve: fix fill_info when using collect_metadata

Since 9b4437a5b870 ("geneve: Unify LWT and netdev handling.") fill_info
does not return UDP_ZERO_CSUM6_RX when using COLLECT_METADATA. This is
because it uses ip_tunnel_info_af() with the device level info, which is
not valid for COLLECT_METADATA.

Fix by checking for the presence of the actual sockets.

Fixes: 9b4437a5b870 ("geneve: Unify LWT and netdev handling.")
Signed-off-by: Eric Garver <e@erig.me>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfs: Move handling of missing page into one place in xfs_find_get_desired_pgoff()

Currently several places in xfs_find_get_desired_pgoff() handle the case
of a missing page. Make them all handled in one place after the loop has
terminated.

Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>

xfs: Fix off-by-in in loop termination in xfs_find_get_desired_pgoff()

There is an off-by-one error in loop termination conditions in
xfs_find_get_desired_pgoff() since 'end' may index a page beyond end of
desired range if 'endoff' is page aligned. It doesn't have any visible
effects but still it is good to fix it.

Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>

xfs: Fix missed holes in SEEK_HOLE implementation

XFS SEEK_HOLE implementation could miss a hole in an unwritten extent as
can be seen by the following command:

xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "pwrite 128k 8k"
-c "seek -h 0" file
wrote 57344/57344 bytes at offset 0
56 KiB, 14 ops; 0.0000 sec (49.312 MiB/sec and 12623.9856 ops/sec)
wrote 8192/8192 bytes at offset 131072
8 KiB, 2 ops; 0.0000 sec (70.383 MiB/sec and 18018.0180 ops/sec)
Whence Result
HOLE 139264

Where we can see that hole at offset 56k was just ignored by SEEK_HOLE
implementation. The bug is in xfs_find_get_desired_pgoff() which does
not properly detect the case when pages are not contiguous.

Fix the problem by properly detecting when found page has larger offset
than expected.

CC: stable@vger.kernel.org
Fixes: d126d43f631f996daeee5006714fed914be32368
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>

xfs: fix off-by-one on max nr_pages in xfs_find_get_desired_pgoff()

xfs_find_get_desired_pgoff() is used to search for offset of hole or
data in page range [index, end] (both inclusive), and the max number
of pages to search should be at least one, if end == index.
Otherwise the only page is missed and no hole or data is found,
which is not correct.

When block size is smaller than page size, this can be demonstrated
by preallocating a file with size smaller than page size and writing
data to the last block. E.g. run this xfs_io command on a 1k block
size XFS on x86_64 host.

  # xfs_io -fc "falloc 0 3k" -c "pwrite 2k 1k" \
       -c "seek -d 0" /mnt/xfs/testfile
  wrote 1024/1024 bytes at offset 2048
  1 KiB, 1 ops; 0.0000 sec (33.675 MiB/sec and 34482.7586 ops/sec)
  Whence  Result
  DATA    EOF

Data at offset 2k was missed, and lseek(2) returned ENXIO.

This is uncovered by generic/285 subtest 07 and 08 on ppc64 host,
where pagesize is 64k. Because a recent change to generic/285
reduced the preallocated file size to smaller than 64k.

Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>

xfs: fix unaligned access in xfs_btree_visit_blocks

This structure copy was throwing unaligned access warnings on sparc64:

Kernel unaligned access at TPC[1043c088] xfs_btree_visit_blocks+0x88/0xe0 [xfs]

xfs_btree_copy_ptrs does a memcpy, which avoids it.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>

powerpc: Add PPC_FEATURE userspace bits for SCV and DARN instructions

Providing "scv" support to userspace requires kernel support, so it
must be advertised as independently to the base ISA 3 instruction set.

The darn instruction relies on firmware enablement, so it has been
decided to split this out from the core ISA 3 feature as well.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>