git.monstr.eu Git - linux-2.6-microblaze.git/log

net: phy: smsc: fix printing too many logs

Commit 7ae7ad2f11ef47 ("net: phy: smsc: use phy_read_poll_timeout()
to simplify the code") will print a lot of logs as follows when Ethernet
cable is not connected:

[ 4.473105] SMSC LAN8710/LAN8720 2188000.ethernet-1:00: lan87xx_read_status failed: -110

When wait 640 ms for check ENERGYON bit, the timeout should not be
regarded as an actual error and an error message also should not be
printed. due to a hardware bug in LAN87XX device, it leads to unstable
detection of plugging in Ethernet cable when LAN87xx is in Energy Detect
Power-Down mode. the workaround for it involves, when the link is down,
and at each read_status() call:

- disable EDPD mode, forcing the PHY out of low-power mode
- waiting 640ms to see if we have any energy detected from the media
- re-enable entry to EDPD mode

This is presumably enough to allow the PHY to notice that a cable is
connected, and resume normal operations to negotiate with the partner.
The problem is that when no media is detected, the 640ms wait times
out and this commit was modified to prints an error message. it is an
inappropriate conversion by used phy_read_poll_timeout() to introduce
this bug. so fix this issue by use read_poll_timeout() to replace
phy_read_poll_timeout().

Fixes: 7ae7ad2f11ef47 ("net: phy: smsc: use phy_read_poll_timeout() to simplify the code")
Reported-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: update email address for Felix Fietkau

The old address has been bouncing for a while now

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Add MODULE_DESCRIPTION entries to network modules

The user tool modinfo is used to get information on kernel modules, including a
description where it is available.

This patch adds a brief MODULE_DESCRIPTION to the following modules:

9p
drop_monitor
esp4_offload
esp6_offload
fou
fou6
ila
sch_fq
sch_fq_codel
sch_hhf

Signed-off-by: Rob Gill <rrobgill@protonmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rxrpc: Fix notification call on completion of discarded calls

When preallocated service calls are being discarded, they're passed to
->discard_new_call() to have the caller clean up any attached higher-layer
preallocated pieces before being marked completed. However, the act of
marking them completed now invokes the call's notification function - which
causes a problem because that function might assume that the previously
freed pieces of memory are still there.

Fix this by setting a dummy notification function on the socket after
calling ->discard_new_call().

This results in the following kasan message when the kafs module is
removed.

==================================================================
BUG: KASAN: use-after-free in afs_wake_up_async_call+0x6aa/0x770 fs/afs/rxrpc.c:707
Write of size 1 at addr ffff8880946c39e4 by task kworker/u4:1/21

CPU: 0 PID: 21 Comm: kworker/u4:1 Not tainted 5.8.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x18f/0x20d lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd3/0x413 mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
afs_wake_up_async_call+0x6aa/0x770 fs/afs/rxrpc.c:707
rxrpc_notify_socket+0x1db/0x5d0 net/rxrpc/recvmsg.c:40
__rxrpc_set_call_completion.part.0+0x172/0x410 net/rxrpc/recvmsg.c:76
__rxrpc_call_completed net/rxrpc/recvmsg.c:112 [inline]
rxrpc_call_completed+0xca/0xf0 net/rxrpc/recvmsg.c:111
rxrpc_discard_prealloc+0x781/0xab0 net/rxrpc/call_accept.c:233
rxrpc_listen+0x147/0x360 net/rxrpc/af_rxrpc.c:245
afs_close_socket+0x95/0x320 fs/afs/rxrpc.c:110
afs_net_exit+0x1bc/0x310 fs/afs/main.c:155
ops_exit_list.isra.0+0xa8/0x150 net/core/net_namespace.c:186
cleanup_net+0x511/0xa50 net/core/net_namespace.c:603
process_one_work+0x965/0x1690 kernel/workqueue.c:2269
worker_thread+0x96/0xe10 kernel/workqueue.c:2415
kthread+0x3b5/0x4a0 kernel/kthread.c:291
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293

Allocated by task 6820:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc mm/kasan/common.c:494 [inline]
__kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:467
kmem_cache_alloc_trace+0x153/0x7d0 mm/slab.c:3551
kmalloc include/linux/slab.h:555 [inline]
kzalloc include/linux/slab.h:669 [inline]
afs_alloc_call+0x55/0x630 fs/afs/rxrpc.c:141
afs_charge_preallocation+0xe9/0x2d0 fs/afs/rxrpc.c:757
afs_open_socket+0x292/0x360 fs/afs/rxrpc.c:92
afs_net_init+0xa6c/0xe30 fs/afs/main.c:125
ops_init+0xaf/0x420 net/core/net_namespace.c:151
setup_net+0x2de/0x860 net/core/net_namespace.c:341
copy_net_ns+0x293/0x590 net/core/net_namespace.c:482
create_new_namespaces+0x3fb/0xb30 kernel/nsproxy.c:110
unshare_nsproxy_namespaces+0xbd/0x1f0 kernel/nsproxy.c:231
ksys_unshare+0x43d/0x8e0 kernel/fork.c:2983
__do_sys_unshare kernel/fork.c:3051 [inline]
__se_sys_unshare kernel/fork.c:3049 [inline]
__x64_sys_unshare+0x2d/0x40 kernel/fork.c:3049
do_syscall_64+0x60/0xe0 arch/x86/entry/common.c:359
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Freed by task 21:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
kasan_set_free_info mm/kasan/common.c:316 [inline]
__kasan_slab_free+0xf7/0x140 mm/kasan/common.c:455
__cache_free mm/slab.c:3426 [inline]
kfree+0x109/0x2b0 mm/slab.c:3757
afs_put_call+0x585/0xa40 fs/afs/rxrpc.c:190
rxrpc_discard_prealloc+0x764/0xab0 net/rxrpc/call_accept.c:230
rxrpc_listen+0x147/0x360 net/rxrpc/af_rxrpc.c:245
afs_close_socket+0x95/0x320 fs/afs/rxrpc.c:110
afs_net_exit+0x1bc/0x310 fs/afs/main.c:155
ops_exit_list.isra.0+0xa8/0x150 net/core/net_namespace.c:186
cleanup_net+0x511/0xa50 net/core/net_namespace.c:603
process_one_work+0x965/0x1690 kernel/workqueue.c:2269
worker_thread+0x96/0xe10 kernel/workqueue.c:2415
kthread+0x3b5/0x4a0 kernel/kthread.c:291
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293

The buggy address belongs to the object at ffff8880946c3800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 484 bytes inside of
1024-byte region [ffff8880946c3800, ffff8880946c3c00)
The buggy address belongs to the page:
page:ffffea000251b0c0 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0xfffe0000000200(slab)
raw: 00fffe0000000200 ffffea0002546508 ffffea00024fa248 ffff8880aa000c40
raw: 0000000000000000 ffff8880946c3000 0000000100000002 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
ffff8880946c3880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880946c3900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8880946c3980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8880946c3a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880946c3a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================

Reported-by: syzbot+d3eccef36ddbd02713e9@syzkaller.appspotmail.com
Fixes: 5ac0d62226a0 ("rxrpc: Fix missing notification")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'ieee802154-for-davem-2020-06-19' of git://git./linux/kernel/git/sschmidt/wpan

Stefan Schmidt says:

====================
pull-request: ieee802154 for net 2020-06-19

An update from ieee802154 for your *net* tree.

Just two small maintenance fixes to update references to the new project
homepage.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tc-testing: update geneve options match in tunnel_key unit tests

Since iproute2 commit f72c3ad00f3b ("tc: m_tunnel_key: add options
support for vxlan"), the geneve opt output use key word "geneve_opts"
instead of "geneve_opt". To make compatibility for both old and new
iproute2, let's accept both "geneve_opt" and "geneve_opts".

Suggested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: fix firmware not resetting tp->ocp_base

Typically the firmware takes care that tp->ocp_base is reset to its
default value. That's not the case (at least) for RTL8117.
As a result subsequent PHY access reads/writes the wrong page and
the link is broken. Fix this be resetting tp->ocp_base explicitly.

Fixes: 229c1e0dfd3d ("r8169: load firmware for RTL8168fp/RTL8117")
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmvnic: continue to init in CRQ reset returns H_CLOSED

Continue the reset path when partner adapter is not ready or H_CLOSED is
returned from reset crq. This patch allows the CRQ init to proceed to
establish a valid CRQ for traffic to flow after reset.

Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: tame the watchdog timer on reconfig

Even with moving netif_tx_disable() to an earlier point when
taking down the queues for a reconfiguration, we still end
up with the occasional netdev watchdog Tx Timeout complaint.
The old method of using netif_trans_update() works fine for
queue 0, but has no effect on the remaining queues. Using
netif_device_detach() allows us to signal to the watchdog to
ignore us for the moment.

Fixes: beead698b173 ("ionic: Add the basic NDO callbacks for netdev support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests/net: report etf errors correctly

The ETF qdisc can queue skbs that it could not pace on the errqueue.

Address a few issues in the selftest

- recv buffer size was too small, and incorrectly calculated
- compared errno to ee_code instead of ee_errno
- missed invalid request error type

v2:
- fix a few checkpatch --strict indentation warnings

Fixes: ea6a547669b3 ("selftests/net: make so_txtime more robust to timer variance")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ibmveth: Fix max MTU limit

The max MTU limit defined for ibmveth is not accounting for
virtual ethernet buffer overhead, which is twenty-two additional
bytes set aside for the ethernet header and eight additional bytes
of an opaque handle reserved for use by the hypervisor. Update the
max MTU to reflect this overhead.

Fixes: d894be57ca92 ("ethernet: use net core MTU range checking in more drivers")
Fixes: 110447f8269a ("ethernet: fix min/max MTU typos")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'several-fixes-for-indirect-flow_blocks-offload'

wenxu says:

====================
several fixes for indirect flow_blocks offload

v2:
patch2: store the cb_priv of representor to the flow_block_cb->indr.cb_priv
in the driver. And make the correct check with the statments
this->indr.cb_priv == cb_priv

patch4: del the driver list only in the indriect cleanup callbacks

v3:
add the cover letter and changlogs.

v4:
collapsed 1/4, 2/4, 4/4 in v3 to one fix
Add the prepare patch 1 and 2

v5:
patch1: place flow_indr_block_cb_alloc() right before
flow_indr_dev_setup_offload() to avoid moving flow_block_indr_init()

This series fixes commit 1fac52da5942 ("net: flow_offload: consolidate
indirect flow_block infrastructure") that revists the flow_block
infrastructure.

patch #1 #2: prepare for fix patch #3
add and use flow_indr_block_cb_alloc/remove function

patch #3: fix flow_indr_dev_unregister path
If the representor is removed, then identify the indirect flow_blocks
that need to be removed by the release callback and the port representor
structure. To identify the port representor structure, a new
indr.cb_priv field needs to be introduced. The flow_block also needs to
be removed from the driver list from the cleanup path

patch#4 fix block->nooffloaddevcnt warning dmesg log.
When a indr device add in offload success. The block->nooffloaddevcnt
should be 0. After the representor go away. When the dir device go away
the flow_block UNBIND operation with -EOPNOTSUPP which lead the warning
demesg log.
The block->nooffloaddevcnt should always count for indr block.
even the indr block offload successful. The representor maybe
gone away and the ingress qdisc can work in software mode.
====================

Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sched: cls_api: fix nooffloaddevcnt warning dmesg log

The block->nooffloaddevcnt should always count for indr block.
even the indr block offload successful. The representor maybe
gone away and the ingress qdisc can work in software mode.

block->nooffloaddevcnt warning with following dmesg log:

[  760.667058] #####################################################
[  760.668186] ## TEST test-ecmp-add-vxlan-encap-disable-sriov.sh ##
[  760.669179] #####################################################
[  761.780655] :test: Fedora 30 (Thirty)
[  761.783794] :test: Linux reg-r-vrt-018-180 5.7.0+
[  761.822890] :test: NIC ens1f0 FW 16.26.6000 PCI 0000:81:00.0 DEVICE 0x1019 ConnectX-5 Ex
[  761.860244] mlx5_core 0000:81:00.0 ens1f0: Link up
[  761.880693] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f0: link becomes ready
[  762.059732] mlx5_core 0000:81:00.1 ens1f1: Link up
[  762.234341] :test: unbind vfs of ens1f0
[  762.257825] :test: Change ens1f0 eswitch (0000:81:00.0) mode to switchdev
[  762.291363] :test: unbind vfs of ens1f1
[  762.306914] :test: Change ens1f1 eswitch (0000:81:00.1) mode to switchdev
[  762.309237] mlx5_core 0000:81:00.1: E-Switch: Disable: mode(LEGACY), nvfs(2), active vports(3)
[  763.282598] mlx5_core 0000:81:00.1: E-Switch: Supported tc offload range - chains: 4294967294, prios: 4294967295
[  763.362825] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0)
[  763.444465] mlx5_core 0000:81:00.1 ens1f1: renamed from eth0
[  763.460088] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0)
[  763.502586] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0)
[  763.552429] ens1f1_0: renamed from eth0
[  763.569569] mlx5_core 0000:81:00.1: E-Switch: Enable: mode(OFFLOADS), nvfs(2), active vports(3)
[  763.629694] ens1f1_1: renamed from eth1
[  764.631552] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1_0: link becomes ready
[  764.670841] :test: unbind vfs of ens1f0
[  764.681966] :test: unbind vfs of ens1f1
[  764.726762] mlx5_core 0000:81:00.0 ens1f0: Link up
[  764.766511] mlx5_core 0000:81:00.1 ens1f1: Link up
[  764.797325] :test: Add multipath vxlan encap rule and disable sriov
[  764.798544] :test: config multipath route
[  764.812732] mlx5_core 0000:81:00.0: lag map port 1:2 port 2:2
[  764.874556] mlx5_core 0000:81:00.0: modify lag map port 1:1 port 2:2
[  765.603681] :test: OK
[  765.659048] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1_1: link becomes ready
[  765.675085] :test: verify rule in hw
[  765.694237] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f0: link becomes ready
[  765.711892] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1: link becomes ready
[  766.979230] :test: OK
[  768.125419] :test: OK
[  768.127519] :test: - disable sriov ens1f1
[  768.131160] pci 0000:81:02.2: Removing from iommu group 75
[  768.132646] pci 0000:81:02.3: Removing from iommu group 76
[  769.179749] mlx5_core 0000:81:00.1: E-Switch: Disable: mode(OFFLOADS), nvfs(2), active vports(3)
[  769.455627] mlx5_core 0000:81:00.0: modify lag map port 1:1 port 2:1
[  769.703990] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0)
[  769.988637] mlx5_core 0000:81:00.1 ens1f1: renamed from eth0
[  769.990022] :test: - disable sriov ens1f0
[  769.994922] pci 0000:81:00.2: Removing from iommu group 73
[  769.997048] pci 0000:81:00.3: Removing from iommu group 74
[  771.035813] mlx5_core 0000:81:00.0: E-Switch: Disable: mode(OFFLOADS), nvfs(2), active vports(3)
[  771.339091] ------------[ cut here ]------------
[  771.340812] WARNING: CPU: 6 PID: 3448 at net/sched/cls_api.c:749 tcf_block_offload_unbind.isra.0+0x5c/0x60
[  771.341728] Modules linked in: act_mirred act_tunnel_key cls_flower dummy vxlan ip6_udp_tunnel udp_tunnel sch_ingress nfsv3 nfs_acl nfs lockd grace fscache tun bridge stp llc sunrpc rdma_ucm rdma_cm iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5_core intel_rapl_msr intel_rapl_common sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp mlxfw act_ct nf_flow_table kvm_intel nf_nat kvm nf_conntrack irqbypass crct10dif_pclmul igb crc32_pclmul nf_defrag_ipv6 libcrc32c nf_defrag_ipv4 crc32c_intel ghash_clmulni_intel ptp ipmi_ssif intel_cstate pps_c
ore ses intel_uncore mei_me iTCO_wdt joydev ipmi_si iTCO_vendor_support i2c_i801 enclosure mei ioatdma dca lpc_ich wmi ipmi_devintf pcspkr acpi_power_meter ipmi_msghandler acpi_pad ast i2c_algo_bit drm_vram_helper drm_kms_helper drm_ttm_helper ttm drm mpt3sas raid_class scsi_transport_sas
[  771.347818] CPU: 6 PID: 3448 Comm: test-ecmp-add-v Not tainted 5.7.0+ #1146
[  771.348727] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[  771.349646] RIP: 0010:tcf_block_offload_unbind.isra.0+0x5c/0x60
[  771.350553] Code: 4a fd ff ff 83 f8 a1 74 0e 5b 4c 89 e7 5d 41 5c 41 5d e9 07 93 89 ff 8b 83 a0 00 00 00 8d 50 ff 89 93 a0 00 00 00 85 c0 75 df <0f> 0b eb db 0f 1f 44 00 00 41 57 41 56 41 55 41 89 cd 41 54 49 89
[  771.352420] RSP: 0018:ffffb33144cd3b00 EFLAGS: 00010246
[  771.353353] RAX: 0000000000000000 RBX: ffff8b37cf4b2800 RCX: 0000000000000000
[  771.354294] RDX: 00000000ffffffff RSI: ffff8b3b9aad0000 RDI: ffffffff8d5c6e20
[  771.355245] RBP: ffff8b37eb546948 R08: ffffffffc0b7a348 R09: ffff8b3b9aad0000
[  771.356189] R10: 0000000000000001 R11: ffff8b3ba7a0a1c0 R12: ffff8b37cf4b2850
[  771.357123] R13: ffff8b3b9aad0000 R14: ffff8b37cf4b2820 R15: ffff8b37cf4b2820
[  771.358039] FS:  00007f8a19b6e740(0000) GS:ffff8b3befa00000(0000) knlGS:0000000000000000
[  771.358965] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  771.359885] CR2: 00007f3afb91c1a0 CR3: 000000045133c004 CR4: 00000000001606e0
[  771.360825] Call Trace:
[  771.361764]  __tcf_block_put+0x84/0x150
[  771.362712]  ingress_destroy+0x1b/0x20 [sch_ingress]
[  771.363658]  qdisc_destroy+0x3e/0xc0
[  771.364594]  dev_shutdown+0x7a/0xa5
[  771.365522]  rollback_registered_many+0x20d/0x530
[  771.366458]  ? netdev_upper_dev_unlink+0x15d/0x1c0
[  771.367387]  unregister_netdevice_many.part.0+0xf/0x70
[  771.368310]  vxlan_netdevice_event+0xa4/0x110 [vxlan]
[  771.369454]  notifier_call_chain+0x4c/0x70
[  771.370579]  rollback_registered_many+0x2f5/0x530
[  771.371719]  rollback_registered+0x56/0x90
[  771.372843]  unregister_netdevice_queue+0x73/0xb0
[  771.373982]  unregister_netdev+0x18/0x20
[  771.375168]  mlx5e_vport_rep_unload+0x56/0xc0 [mlx5_core]
[  771.376327]  esw_offloads_disable+0x81/0x90 [mlx5_core]
[  771.377512]  mlx5_eswitch_disable_locked.cold+0xcb/0x1af [mlx5_core]
[  771.378679]  mlx5_eswitch_disable+0x44/0x60 [mlx5_core]
[  771.379822]  mlx5_device_disable_sriov+0xad/0xb0 [mlx5_core]
[  771.380968]  mlx5_core_sriov_configure+0xc1/0xe0 [mlx5_core]
[  771.382087]  sriov_numvfs_store+0xfc/0x130
[  771.383195]  kernfs_fop_write+0xce/0x1b0
[  771.384302]  vfs_write+0xb6/0x1a0
[  771.385410]  ksys_write+0x5f/0xe0
[  771.386500]  do_syscall_64+0x5b/0x1d0
[  771.387569]  entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 0fdcf78d5973 ("net: use flow_indr_dev_setup_offload()")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: flow_offload: fix flow_indr_dev_unregister path

If the representor is removed, then identify the indirect flow_blocks
that need to be removed by the release callback and the port representor
structure. To identify the port representor structure, a new
indr.cb_priv field needs to be introduced. The flow_block also needs to
be removed from the driver list from the cleanup path.

Fixes: 1fac52da5942 ("net: flow_offload: consolidate indirect flow_block infrastructure")

Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

flow_offload: use flow_indr_block_cb_alloc/remove function

Prepare fix the bug in the next patch. use flow_indr_block_cb_alloc/remove
function and remove the __flow_block_indr_binding.

Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

flow_offload: add flow_indr_block_cb_alloc/remove function

Add flow_indr_block_cb_alloc/remove function for next fix patch.

Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

geneve: allow changing DF behavior after creation

Currently, trying to change the DF parameter of a geneve device does
nothing:

    # ip -d link show geneve1
    14: geneve1: <snip>
        link/ether <snip>
        geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>
    # ip link set geneve1 type geneve id 1 df unset
    # ip -d link show geneve1
    14: geneve1: <snip>
        link/ether <snip>
        geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip>

We just need to update the value in geneve_changelink.

Fixes: a025fb5f49ad ("geneve: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enetc: Fix HW_VLAN_CTAG_TX|RX toggling

VLAN tag insertion/extraction offload is correctly
activated at probe time but deactivation of this feature
(i.e. via ethtool) is broken. Toggling works only for
Tx/Rx ring 0 of a PF, and is ignored for the other rings,
including the VF rings.
To fix this, the existing VLAN offload toggling code
was extended to all the rings assigned to a netdevice,
instead of the default ring 0 (likely a leftover from the
early validation days of this feature). And the code was
moved to the common set_features() function to fix toggling
for the VF driver too.

Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: macb: undo operations in case of failure

Undo previously done operation in case macb_phylink_connect()
fails. Since macb_reset_hw() is the 1st undo operation the
napi_exit label was renamed to reset_hw.

Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-fixes-20200618' of git://git./linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Performance drop fix and other fixes

Here are three fixes for rxrpc:

(1) Fix a trace symbol mapping.  It doesn't seem to let you map to "".

(2) Fix the handling of the remote receive window size when it increases
     beyond the size we can support for our transmit window.

(3) Fix a performance drop caused by retransmitted packets being
     accidentally marked as already ACK'd.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-phy-MDIO-bus-scanning-fixes'

Florian Fainelli says:

====================
net: phy: MDIO bus scanning fixes

This patch series fixes two problems with the current MDIO bus scanning
logic which was identified while moving from 4.9 to 5.4 on devices that
do rely on scanning the MDIO bus at runtime because they use pluggable
cards.

Changes in v2:

- added comment explaining the special value of -ENODEV
- added Andrew's Reviewed-by tag
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: Check harder for errors in get_phy_id()

Commit 02a6efcab675 ("net: phy: allow scanning busses with missing
phys") added a special condition to return -ENODEV in case -ENODEV or
-EIO was returned from the first read of the MII_PHYSID1 register.

In case the MDIO bus data line pull-up is not strong enough, the MDIO
bus controller will not flag this as a read error. This can happen when
a pluggable daughter card is not connected and weak internal pull-ups
are used (since that is the only option, otherwise the pins are
floating).

The second read of MII_PHYSID2 will be correctly flagged an error
though, but now we will return -EIO which will be treated as a hard
error, thus preventing MDIO bus scanning loops to continue succesfully.

Apply the same logic to both register reads, thus allowing the scanning
logic to proceed.

Fixes: 02a6efcab675 ("net: phy: allow scanning busses with missing phys")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

of: of_mdio: Correct loop scanning logic

Commit 209c65b61d94 ("drivers/of/of_mdio.c:fix of_mdiobus_register()")
introduced a break of the loop on the premise that a successful
registration should exit the loop. The premise is correct but not to
code, because rc && rc != -ENODEV is just a special error condition,
that means we would exit the loop even with rc == -ENODEV which is
absolutely not correct since this is the error code to indicate to the
MDIO bus layer that scanning should continue.

Fix this by explicitly checking for rc = 0 as the only valid condition
to break out of the loop.

Fixes: 209c65b61d94 ("drivers/of/of_mdio.c:fix of_mdiobus_register()")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: oki-semi: pch_gbe: fix spelling mistake

Fix typo: "Triger" --> "Trigger"

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: update ieee802154 project website URL

Update URL to our new home.

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

docs: net: ieee802154: change link to new project URL

We finally came around to setup a new project website.
Update the reference here.

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

net: ethernet: neterion: vxge: fix spelling mistake

Fix typo: "trigered" --> "triggered"

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec

Steffen Klassert says:

====================
pull request (net): ipsec 2020-06-19

1) Fix double ESP trailer insertion in IPsec crypto offload if
   netif_xmit_frozen_or_stopped is true. From Huy Nguyen.

2) Merge fixup for "remove output_finish indirection from
   xfrm_state_afinfo". From Stephen Rothwell.

3) Select CRYPTO_SEQIV for ESP as this is needed for GCM and several
   other encryption algorithms. Also modernize the crypto algorithm
   selections for ESP and AH, remove those that are maked as "MUST NOT"
   and add those that are marked as "MUST" be implemented in RFC 8221.
   From Eric Biggers.

Please note the merge conflict between commit:

a7f7f6248d97 ("treewide: replace '---help---' in Kconfig files with 'help'")

from Linus' tree and commits:

7d4e39195925 ("esp, ah: consolidate the crypto algorithm selections")
be01369859b8 ("esp, ah: modernize the crypto algorithm selections")

from the ipsec tree.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/net-queue

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2020-06-18

This series contains fixes to ixgbe, i40e and ice driver.

Ciara fixes up the ixgbe, i40e and ice drivers to protect access when
allocating and freeing the rings. In addition, made use of READ_ONCE
when reading the rings prior to accessing the statistics pointer.

Björn fixes a crash where the receive descriptor ring allocation was
moved to a different function, which broke the ethtool set_ringparam()
hook.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

i40e: fix crash when Rx descriptor count is changed

When the AF_XDP buffer allocator was introduced, the Rx SW ring
"rx_bi" allocation was moved from i40e_setup_rx_descriptors()
function, and was instead done in the i40e_configure_rx_ring()
function.

This broke the ethtool set_ringparam() hook for changing the Rx
descriptor count, which was relying on i40e_setup_rx_descriptors() to
handle the allocation.

Fix this by adding an explicit i40e_alloc_rx_bi() call to
i40e_set_ringparam().

Fixes: be1222b585fd ("i40e: Separate kernel allocated rx_bi rings from AF_XDP rings")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ice: protect ring accesses with WRITE_ONCE

The READ_ONCE macro is used when reading rings prior to accessing the
statistics pointer. The corresponding WRITE_ONCE usage when allocating and
freeing the rings to ensure protected access was not in place. Introduce
this.

Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e: protect ring accesses with READ- and WRITE_ONCE

READ_ONCE should be used when reading rings prior to accessing the
statistics pointer. Introduce this as well as the corresponding WRITE_ONCE
usage when allocating and freeing the rings, to ensure protected access.

Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe: protect ring accesses with READ- and WRITE_ONCE

READ_ONCE should be used when reading rings prior to accessing the
statistics pointer. Introduce this as well as the corresponding WRITE_ONCE
usage when allocating and freeing the rings, to ensure protected access.

Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

net: increment xmit_recursion level in dev_direct_xmit()

Back in commit f60e5990d9c1 ("ipv6: protect skb->sk accesses
from recursive dereference inside the stack") Hannes added code
so that IPv6 stack would not trust skb->sk for typical cases
where packet goes through 'standard' xmit path (__dev_queue_xmit())

Alas af_packet had a dev_direct_xmit() path that was not
dealing yet with xmit_recursion level.

Also change sk_mc_loop() to dump a stack once only.

Without this patch, syzbot was able to trigger :

[1]
[  153.567378] WARNING: CPU: 7 PID: 11273 at net/core/sock.c:721 sk_mc_loop+0x51/0x70
[  153.567378] Modules linked in: nfnetlink ip6table_raw ip6table_filter iptable_raw iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 nf_defrag_ipv6 iptable_filter macsec macvtap tap macvlan 8021q hsr wireguard libblake2s blake2s_x86_64 libblake2s_generic udp_tunnel ip6_udp_tunnel libchacha20poly1305 poly1305_x86_64 chacha_x86_64 libchacha curve25519_x86_64 libcurve25519_generic netdevsim batman_adv dummy team bridge stp llc w1_therm wire i2c_mux_pca954x i2c_mux cdc_acm ehci_pci ehci_hcd mlx4_en mlx4_ib ib_uverbs ib_core mlx4_core
[  153.567386] CPU: 7 PID: 11273 Comm: b159172088 Not tainted 5.8.0-smp-DEV #273
[  153.567387] RIP: 0010:sk_mc_loop+0x51/0x70
[  153.567388] Code: 66 83 f8 0a 75 24 0f b6 4f 12 b8 01 00 00 00 31 d2 d3 e0 a9 bf ef ff ff 74 07 48 8b 97 f0 02 00 00 0f b6 42 3a 83 e0 01 5d c3 <0f> 0b b8 01 00 00 00 5d c3 0f b6 87 18 03 00 00 5d c0 e8 04 83 e0
[  153.567388] RSP: 0018:ffff95c69bb93990 EFLAGS: 00010212
[  153.567388] RAX: 0000000000000011 RBX: ffff95c6e0ee3e00 RCX: 0000000000000007
[  153.567389] RDX: ffff95c69ae50000 RSI: ffff95c6c30c3000 RDI: ffff95c6c30c3000
[  153.567389] RBP: ffff95c69bb93990 R08: ffff95c69a77f000 R09: 0000000000000008
[  153.567389] R10: 0000000000000040 R11: 00003e0e00026128 R12: ffff95c6c30c3000
[  153.567390] R13: ffff95c6cc4fd500 R14: ffff95c6f84500c0 R15: ffff95c69aa13c00
[  153.567390] FS:  00007fdc3a283700(0000) GS:ffff95c6ff9c0000(0000) knlGS:0000000000000000
[  153.567390] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  153.567391] CR2: 00007ffee758e890 CR3: 0000001f9ba20003 CR4: 00000000001606e0
[  153.567391] Call Trace:
[  153.567391]  ip6_finish_output2+0x34e/0x550
[  153.567391]  __ip6_finish_output+0xe7/0x110
[  153.567391]  ip6_finish_output+0x2d/0xb0
[  153.567392]  ip6_output+0x77/0x120
[  153.567392]  ? __ip6_finish_output+0x110/0x110
[  153.567392]  ip6_local_out+0x3d/0x50
[  153.567392]  ipvlan_queue_xmit+0x56c/0x5e0
[  153.567393]  ? ksize+0x19/0x30
[  153.567393]  ipvlan_start_xmit+0x18/0x50
[  153.567393]  dev_direct_xmit+0xf3/0x1c0
[  153.567393]  packet_direct_xmit+0x69/0xa0
[  153.567394]  packet_sendmsg+0xbf0/0x19b0
[  153.567394]  ? plist_del+0x62/0xb0
[  153.567394]  sock_sendmsg+0x65/0x70
[  153.567394]  sock_write_iter+0x93/0xf0
[  153.567394]  new_sync_write+0x18e/0x1a0
[  153.567395]  __vfs_write+0x29/0x40
[  153.567395]  vfs_write+0xb9/0x1b0
[  153.567395]  ksys_write+0xb1/0xe0
[  153.567395]  __x64_sys_write+0x1a/0x20
[  153.567395]  do_syscall_64+0x43/0x70
[  153.567396]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[  153.567396] RIP: 0033:0x453549
[  153.567396] Code: Bad RIP value.
[  153.567396] RSP: 002b:00007fdc3a282cc8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[  153.567397] RAX: ffffffffffffffda RBX: 00000000004d32d0 RCX: 0000000000453549
[  153.567397] RDX: 0000000000000020 RSI: 0000000020000300 RDI: 0000000000000003
[  153.567398] RBP: 00000000004d32d8 R08: 0000000000000000 R09: 0000000000000000
[  153.567398] R10: 0000000000000000 R11: 0000000000000246 R12: 00000000004d32dc
[  153.567398] R13: 00007ffee742260f R14: 00007fdc3a282dc0 R15: 00007fdc3a283700
[  153.567399] ---[ end trace c1d5ae2b1059ec62 ]---

f60e5990d9c1 ("ipv6: protect skb->sk accesses from recursive dereference inside the stack")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: bcm_sf2: Fix node reference count

of_find_node_by_name() will do an of_node_put() on the "from" argument.
With CONFIG_OF_DYNAMIC enabled which checks for device_node reference
counts, we would be getting a warning like this:

[    6.347230] refcount_t: increment on 0; use-after-free.
[    6.352498] WARNING: CPU: 3 PID: 77 at lib/refcount.c:156
refcount_inc_checked+0x38/0x44
[    6.360601] Modules linked in:
[    6.363661] CPU: 3 PID: 77 Comm: kworker/3:1 Tainted: G        W
5.4.46-gb78b3e9956e6 #13
[    6.372546] Hardware name: BCM97278SV (DT)
[    6.376649] Workqueue: events deferred_probe_work_func
[    6.381796] pstate: 60000005 (nZCv daif -PAN -UAO)
[    6.386595] pc : refcount_inc_checked+0x38/0x44
[    6.391133] lr : refcount_inc_checked+0x38/0x44
...
[    6.478791] Call trace:
[    6.481243]  refcount_inc_checked+0x38/0x44
[    6.485433]  kobject_get+0x3c/0x4c
[    6.488840]  of_node_get+0x24/0x34
[    6.492247]  of_irq_find_parent+0x3c/0xe0
[    6.496263]  of_irq_parse_one+0xe4/0x1d0
[    6.500191]  irq_of_parse_and_map+0x44/0x84
[    6.504381]  bcm_sf2_sw_probe+0x22c/0x844
[    6.508397]  platform_drv_probe+0x58/0xa8
[    6.512413]  really_probe+0x238/0x3fc
[    6.516081]  driver_probe_device+0x11c/0x12c
[    6.520358]  __device_attach_driver+0xa8/0x100
[    6.524808]  bus_for_each_drv+0xb4/0xd0
[    6.528650]  __device_attach+0xd0/0x164
[    6.532493]  device_initial_probe+0x24/0x30
[    6.536682]  bus_probe_device+0x38/0x98
[    6.540524]  deferred_probe_work_func+0xa8/0xd4
[    6.545061]  process_one_work+0x178/0x288
[    6.549078]  process_scheduled_works+0x44/0x48
[    6.553529]  worker_thread+0x218/0x270
[    6.557285]  kthread+0xdc/0xe4
[    6.560344]  ret_from_fork+0x10/0x18
[    6.563925] ---[ end trace 68f65caf69bb152a ]---

Fix this by adding a of_node_get() to increment the reference count
prior to the call.

Fixes: afa3b592953b ("net: dsa: bcm_sf2: Ensure correct sub-node is parsed")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethtool: add missing NETIF_F_GSO_FRAGLIST feature string

Commit 3b33583265ed ("net: Add fraglist GRO/GSO feature flags") missed
an entry for NETIF_F_GSO_FRAGLIST in netdev_features_strings array. As
a result, fraglist GSO feature is not shown in 'ethtool -k' output and
can't be toggled on/off.
The fix is trivial.

Fixes: 3b33583265ed ("net: Add fraglist GRO/GSO feature flags")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: driver sleeps indefinitely when EEH errors exceed eeh_max_freezes

The driver function tg3_io_error_detected() calls napi_disable twice,
without an intervening napi_enable, when the number of EEH errors exceeds
eeh_max_freezes, resulting in an indefinite sleep while holding rtnl_lock.

Add check for pcierr_recovery which skips code already executed for the
"Frozen" state.

Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bareudp: Fixed multiproto mode configuration

Code to handle multiproto configuration is missing.

Fixes: 4b5f67232d95 ("net: Special handling for IP & MPLS")
Signed-off-by: Martin <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 's390-qeth-fixes'

Julian Wiedmann says:

====================
s390/qeth: fixes 2020-06-17

please apply the following patch series for qeth to netdev's net tree.

The first patch fixes a regression in the error handling for a specific
cmd type. I have some follow-ups queued up for net-next to clean this
up properly...

The second patch fine-tunes the HW offload restrictions that went in
with this merge window. In some setups we don't need to apply them.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: let isolation mode override HW offload restrictions

When a device is configured with ISOLATION_MODE_FWD, traffic never goes
through the internal switch. Don't apply the offload restrictions in
this case.

Fixes: c619e9a6f52f ("s390/qeth: don't use restricted offloads for local traffic")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: fix error handling for isolation mode cmds

Current(?) OSA devices also store their cmd-specific return codes for
SET_ACCESS_CONTROL cmds into the top-level cmd->hdr.return_code.
So once we added stricter checking for the top-level field a while ago,
none of the error logic that rolls back the user's configuration to its
old state is applied any longer.

For this specific cmd, go back to the old model where we peek into the
cmd structure even though the top-level field indicated an error.

Fixes: 686c97ee29c8 ("s390/qeth: fix error handling in adapter command callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'mptcp-cope-with-syncookie-on-MP_JOINs'

Paolo Abeni says:

====================
mptcp: cope with syncookie on MP_JOINs

Currently syncookies on MP_JOIN connections are not handled correctly: the
connections fallback to TCP and are kept alive instead of resetting them at
fallback time.

The first patch propagates the required information up to syn_recv_sock time,
and the 2nd patch addresses the unifying the error path for all MP_JOIN
requests.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

mptcp: drop MP_JOIN request sock on syn cookies

Currently any MPTCP socket using syn cookies will fallback to
TCP at 3rd ack time. In case of MP_JOIN requests, the RFC mandate
closing the child and sockets, but the existing error paths
do not handle the syncookie scenario correctly.

Address the issue always forcing the child shutdown in case of
MP_JOIN fallback.

Fixes: ae2dd7164943 ("mptcp: handle tcp fallback when using syn cookies")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mptcp: cache msk on MP_JOIN init_req

The msk ownership is transferred to the child socket at
3rd ack time, so that we avoid more lookups later. If the
request does not reach the 3rd ack, the MSK reference is
dropped at request sock release time.

As a side effect, fallback is now tracked by a NULL msk
reference instead of zeroed 'mp_join' field. This will
simplify the next patch.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Fix the arp error in some cases

ie.,
$ ifconfig eth0 6.6.6.6 netmask 255.255.255.0

$ ip rule add from 6.6.6.6 table 6666

$ ip route add 9.9.9.9 via 6.6.6.6

$ ping -I 6.6.6.6 9.9.9.9
PING 9.9.9.9 (9.9.9.9) from 6.6.6.6 : 56(84) bytes of data.

3 packets transmitted, 0 received, 100% packet loss, time 2079ms

$ arp
Address HWtype HWaddress Flags Mask Iface
6.6.6.6 (incomplete) eth0

The arp request address is error, this is because fib_table_lookup in
fib_check_nh lookup the destnation 9.9.9.9 nexthop, the scope of
the fib result is RT_SCOPE_LINK,the correct scope is RT_SCOPE_HOST.
Here I add a check of whether this is RT_TABLE_MAIN to solve this problem.

Fixes: 3bfd847203c6 ("net: Use passed in table for nexthop lookups")
Signed-off-by: guodeqing <geffrey.guo@huawei.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'sja1105-fixes'

Vladimir Oltean says:

====================
Fix VLAN checks for SJA1105 DSA tc-flower filters

This fixes a ridiculous situation where the driver, in VLAN-unaware
mode, would refuse accepting any tc filter:

tc filter replace dev sw1p3 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate (...)
Error: sja1105: Can only gate based on {DMAC, VID, PCP}.

tc filter replace dev sw1p3 ingress protocol 802.1Q flower skip_sw \
vlan_id 1 vlan_prio 0 dst_mac 42:be:24:9b:76:20 \
action gate (...)
Error: sja1105: Can only gate based on DMAC.

So, without changing the VLAN awareness state, it says it doesn't want
VLAN-aware rules, and it doesn't want VLAN-unaware rules either. One
would say it's in Schrodinger's state...

Now, the situation has been made worse by commit 7f14937facdc ("net:
dsa: sja1105: keep the VLAN awareness state in a driver variable"),
which made VLAN awareness a ternary attribute, but after inspecting the
code from before that patch with a truth table, it looks like the
logical bug was there even before.

While attempting to fix this, I also noticed some leftover debugging
code in one of the places that needed to be fixed. It would have
appeared in the context of patch 3/3 anyway, so I decided to create a
patch that removes it.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: fix checks for VLAN state in gate action

This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:

- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.

But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.

Fixes: 834f8933d5dd ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: fix checks for VLAN state in redirect action

This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:

- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.

But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.

Fixes: dfacc5a23e22 ("net: dsa: sja1105: support flow-based redirection via virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: remove debugging code in sja1105_vl_gate

This shouldn't be there.

Fixes: 834f8933d5dd ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'act_gate-fixes'

Davide Caratti says:

====================
two fixes for 'act_gate' control plane

- patch 1/2 attempts to fix the error path of tcf_gate_init() when users
  try to configure 'act_gate' rules with wrong parameters
- patch 2/2 is a follow-up of a recent fix for NULL dereference in
  the error path of tcf_gate_init()

further work will introduce a tdc test for 'act_gate'.

changes since v2:
  - fix undefined behavior in patch 1/2
  - improve comment in patch 2/2
changes since v1:
  coding style fixes in patch 1/2 and 2/2
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net/sched: act_gate: fix configuration of the periodic timer

assigning a dummy value of 'clock_id' to avoid cancellation of the cycle
timer before its initialization was a temporary solution, and we still
need to handle the case where act_gate timer parameters are changed by
commands like the following one:

# tc action replace action gate <parameters>

the fix consists in the following items:

1) remove the workaround assignment of 'clock_id', and init the list of
   entries before the first error path after IDR atomic check/allocation
2) validate 'clock_id' earlier: there is no need to do IDR atomic
   check/allocation if we know that 'clock_id' is a bad value
3) use a dedicated function, 'gate_setup_timer()', to ensure that the
   timer is cancelled and re-initialized on action overwrite, and also
   ensure we initialize the timer in the error path of tcf_gate_init()

v3: improve comment in the error path of tcf_gate_init() (thanks to
    Vladimir Oltean)
v2: avoid 'goto' in gate_setup_timer (thanks to Cong Wang)

CC: Ivan Vecera <ivecera@redhat.com>
Fixes: a01c245438c5 ("net/sched: fix a couple of splats in the error path of tfc_gate_init()")
Fixes: a51c328df310 ("net: qos: introduce a gate control flow action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sched: act_gate: fix NULL dereference in tcf_gate_init()

it is possible to see a KASAN use-after-free, immediately followed by a
NULL dereference crash, with the following command:

# tc action add action gate index 3 cycle-time 100000000ns \
> cycle-time-ext 100000000ns clockid CLOCK_TAI

BUG: KASAN: use-after-free in tcf_action_init_1+0x8eb/0x960
Write of size 1 at addr ffff88810a5908bc by task tc/883

CPU: 0 PID: 883 Comm: tc Not tainted 5.7.0+ #188
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
Call Trace:
  dump_stack+0x75/0xa0
  print_address_description.constprop.6+0x1a/0x220
  kasan_report.cold.9+0x37/0x7c
  tcf_action_init_1+0x8eb/0x960
  tcf_action_init+0x157/0x2a0
  tcf_action_add+0xd9/0x2f0
  tc_ctl_action+0x2a3/0x39d
  rtnetlink_rcv_msg+0x5f3/0x920
  netlink_rcv_skb+0x120/0x380
  netlink_unicast+0x439/0x630
  netlink_sendmsg+0x714/0xbf0
  sock_sendmsg+0xe2/0x110
  ____sys_sendmsg+0x5b4/0x890
  ___sys_sendmsg+0xe9/0x160
  __sys_sendmsg+0xd3/0x170
  do_syscall_64+0x9a/0x370
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

[...]

KASAN: null-ptr-deref in range [0x0000000000000070-0x0000000000000077]
CPU: 0 PID: 883 Comm: tc Tainted: G    B             5.7.0+ #188
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
RIP: 0010:tcf_action_fill_size+0xa3/0xf0
[....]
RSP: 0018:ffff88813a48f250 EFLAGS: 00010212
RAX: dffffc0000000000 RBX: 0000000000000094 RCX: ffffffffa47c3eb6
RDX: 000000000000000e RSI: 0000000000000008 RDI: 0000000000000070
RBP: ffff88810a590800 R08: 0000000000000004 R09: ffffed1027491e03
R10: 0000000000000003 R11: ffffed1027491e03 R12: 0000000000000000
R13: 0000000000000000 R14: dffffc0000000000 R15: ffff88810a590800
FS:  00007f62cae8ce40(0000) GS:ffff888147c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f62c9d20a10 CR3: 000000013a52a000 CR4: 0000000000340ef0
Call Trace:
  tcf_action_init+0x172/0x2a0
  tcf_action_add+0xd9/0x2f0
  tc_ctl_action+0x2a3/0x39d
  rtnetlink_rcv_msg+0x5f3/0x920
  netlink_rcv_skb+0x120/0x380
  netlink_unicast+0x439/0x630
  netlink_sendmsg+0x714/0xbf0
  sock_sendmsg+0xe2/0x110
  ____sys_sendmsg+0x5b4/0x890
  ___sys_sendmsg+0xe9/0x160
  __sys_sendmsg+0xd3/0x170
  do_syscall_64+0x9a/0x370
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

this is caused by the test on 'cycletime_ext', that is still unassigned
when the action is newly created. This makes the action .init() return 0
without calling tcf_idr_insert(), hence the UAF + crash.

rework the logic that prevents zero values of cycle-time, as follows:

1) 'tcfg_cycletime_ext' seems to be unused in the action software path,
   and it was already possible by other means to obtain non-zero
   cycletime and zero cycletime-ext. So, removing that test should not
   cause any damage.
2) while at it, we must prevent overwriting configuration data with wrong
   ones: use a temporary variable for 'tcfg_cycletime', and validate it
   preserving the original semantic (that allowed computing the cycle
   time as the sum of all intervals, when not specified by
   TCA_GATE_CYCLE_TIME).
3) remove the test on 'tcfg_cycletime', no more useful, and avoid
   returning -EFAULT, which did not seem an appropriate return value for
   a wrong netlink attribute.

v3: fix uninitialized 'cycletime' (thanks to Vladimir Oltean)
v2: remove useless 'return;' at the end of void gate_get_start_time()

Fixes: a51c328df310 ("net: qos: introduce a gate control flow action")
CC: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_tunnel: fix use-after-free in ip_tunnel_lookup()

In the datapath, the ip_tunnel_lookup() is used and it internally uses
fallback tunnel device pointer, which is fb_tunnel_dev.
This pointer variable should be set to NULL when a fb interface is deleted.
But there is no routine to set fb_tunnel_dev pointer to NULL.
So, this pointer will be still used after interface is deleted and
it eventually results in the use-after-free problem.

Test commands:
    ip netns add A
    ip netns add B
    ip link add eth0 type veth peer name eth1
    ip link set eth0 netns A
    ip link set eth1 netns B

    ip netns exec A ip link set lo up
    ip netns exec A ip link set eth0 up
    ip netns exec A ip link add gre1 type gre local 10.0.0.1 \
    remote 10.0.0.2
    ip netns exec A ip link set gre1 up
    ip netns exec A ip a a 10.0.100.1/24 dev gre1
    ip netns exec A ip a a 10.0.0.1/24 dev eth0

    ip netns exec B ip link set lo up
    ip netns exec B ip link set eth1 up
    ip netns exec B ip link add gre1 type gre local 10.0.0.2 \
    remote 10.0.0.1
    ip netns exec B ip link set gre1 up
    ip netns exec B ip a a 10.0.100.2/24 dev gre1
    ip netns exec B ip a a 10.0.0.2/24 dev eth1
    ip netns exec A hping3 10.0.100.2 -2 --flood -d 60000 &
    ip netns del B

Splat looks like:
[   77.793450][    C3] ==================================================================
[   77.794702][    C3] BUG: KASAN: use-after-free in ip_tunnel_lookup+0xcc4/0xf30
[   77.795573][    C3] Read of size 4 at addr ffff888060bd9c84 by task hping3/2905
[   77.796398][    C3]
[   77.796664][    C3] CPU: 3 PID: 2905 Comm: hping3 Not tainted 5.8.0-rc1+ #616
[   77.797474][    C3] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   77.798453][    C3] Call Trace:
[   77.798815][    C3]  <IRQ>
[   77.799142][    C3]  dump_stack+0x9d/0xdb
[   77.799605][    C3]  print_address_description.constprop.7+0x2cc/0x450
[   77.800365][    C3]  ? ip_tunnel_lookup+0xcc4/0xf30
[   77.800908][    C3]  ? ip_tunnel_lookup+0xcc4/0xf30
[   77.801517][    C3]  ? ip_tunnel_lookup+0xcc4/0xf30
[   77.802145][    C3]  kasan_report+0x154/0x190
[   77.802821][    C3]  ? ip_tunnel_lookup+0xcc4/0xf30
[   77.803503][    C3]  ip_tunnel_lookup+0xcc4/0xf30
[   77.804165][    C3]  __ipgre_rcv+0x1ab/0xaa0 [ip_gre]
[   77.804862][    C3]  ? rcu_read_lock_sched_held+0xc0/0xc0
[   77.805621][    C3]  gre_rcv+0x304/0x1910 [ip_gre]
[   77.806293][    C3]  ? lock_acquire+0x1a9/0x870
[   77.806925][    C3]  ? gre_rcv+0xfe/0x354 [gre]
[   77.807559][    C3]  ? erspan_xmit+0x2e60/0x2e60 [ip_gre]
[   77.808305][    C3]  ? rcu_read_lock_sched_held+0xc0/0xc0
[   77.809032][    C3]  ? rcu_read_lock_held+0x90/0xa0
[   77.809713][    C3]  gre_rcv+0x1b8/0x354 [gre]
[ ... ]

Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_gre: fix use-after-free in ip6gre_tunnel_lookup()

In the datapath, the ip6gre_tunnel_lookup() is used and it internally uses
fallback tunnel device pointer, which is fb_tunnel_dev.
This pointer variable should be set to NULL when a fb interface is deleted.
But there is no routine to set fb_tunnel_dev pointer to NULL.
So, this pointer will be still used after interface is deleted and
it eventually results in the use-after-free problem.

Test commands:
    ip netns add A
    ip netns add B
    ip link add eth0 type veth peer name eth1
    ip link set eth0 netns A
    ip link set eth1 netns B

    ip netns exec A ip link set lo up
    ip netns exec A ip link set eth0 up
    ip netns exec A ip link add ip6gre1 type ip6gre local fc:0::1 \
    remote fc:0::2
    ip netns exec A ip -6 a a fc:100::1/64 dev ip6gre1
    ip netns exec A ip link set ip6gre1 up
    ip netns exec A ip -6 a a fc:0::1/64 dev eth0
    ip netns exec A ip link set ip6gre0 up

    ip netns exec B ip link set lo up
    ip netns exec B ip link set eth1 up
    ip netns exec B ip link add ip6gre1 type ip6gre local fc:0::2 \
    remote fc:0::1
    ip netns exec B ip -6 a a fc:100::2/64 dev ip6gre1
    ip netns exec B ip link set ip6gre1 up
    ip netns exec B ip -6 a a fc:0::2/64 dev eth1
    ip netns exec B ip link set ip6gre0 up
    ip netns exec A ping fc:100::2 -s 60000 &
    ip netns del B

Splat looks like:
[   73.087285][    C1] BUG: KASAN: use-after-free in ip6gre_tunnel_lookup+0x1064/0x13f0 [ip6_gre]
[   73.088361][    C1] Read of size 4 at addr ffff888040559218 by task ping/1429
[   73.089317][    C1]
[   73.089638][    C1] CPU: 1 PID: 1429 Comm: ping Not tainted 5.7.0+ #602
[   73.090531][    C1] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   73.091725][    C1] Call Trace:
[   73.092160][    C1]  <IRQ>
[   73.092556][    C1]  dump_stack+0x96/0xdb
[   73.093122][    C1]  print_address_description.constprop.6+0x2cc/0x450
[   73.094016][    C1]  ? ip6gre_tunnel_lookup+0x1064/0x13f0 [ip6_gre]
[   73.094894][    C1]  ? ip6gre_tunnel_lookup+0x1064/0x13f0 [ip6_gre]
[   73.095767][    C1]  ? ip6gre_tunnel_lookup+0x1064/0x13f0 [ip6_gre]
[   73.096619][    C1]  kasan_report+0x154/0x190
[   73.097209][    C1]  ? ip6gre_tunnel_lookup+0x1064/0x13f0 [ip6_gre]
[   73.097989][    C1]  ip6gre_tunnel_lookup+0x1064/0x13f0 [ip6_gre]
[   73.098750][    C1]  ? gre_del_protocol+0x60/0x60 [gre]
[   73.099500][    C1]  gre_rcv+0x1c5/0x1450 [ip6_gre]
[   73.100199][    C1]  ? ip6gre_header+0xf00/0xf00 [ip6_gre]
[   73.100985][    C1]  ? rcu_read_lock_sched_held+0xc0/0xc0
[   73.101830][    C1]  ? ip6_input_finish+0x5/0xf0
[   73.102483][    C1]  ip6_protocol_deliver_rcu+0xcbb/0x1510
[   73.103296][    C1]  ip6_input_finish+0x5b/0xf0
[   73.103920][    C1]  ip6_input+0xcd/0x2c0
[   73.104473][    C1]  ? ip6_input_finish+0xf0/0xf0
[   73.105115][    C1]  ? rcu_read_lock_held+0x90/0xa0
[   73.105783][    C1]  ? rcu_read_lock_sched_held+0xc0/0xc0
[   73.106548][    C1]  ipv6_rcv+0x1f1/0x300
[ ... ]

Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: c12b395a4664 ("gre: Support GRE over IPv6")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: core: reduce recursion limit value

In the current code, ->ndo_start_xmit() can be executed recursively only
10 times because of stack memory.
But, in the case of the vxlan, 10 recursion limit value results in
a stack overflow.
In the current code, the nested interface is limited by 8 depth.
There is no critical reason that the recursion limitation value should
be 10.
So, it would be good to be the same value with the limitation value of
nesting interface depth.

Test commands:
    ip link add vxlan10 type vxlan vni 10 dstport 4789 srcport 4789 4789
    ip link set vxlan10 up
    ip a a 192.168.10.1/24 dev vxlan10
    ip n a 192.168.10.2 dev vxlan10 lladdr fc:22:33:44:55:66 nud permanent

    for i in {9..0}
    do
        let A=$i+1
ip link add vxlan$i type vxlan vni $i dstport 4789 srcport 4789 4789
ip link set vxlan$i up
ip a a 192.168.$i.1/24 dev vxlan$i
ip n a 192.168.$i.2 dev vxlan$i lladdr fc:22:33:44:55:66 nud permanent
bridge fdb add fc:22:33:44:55:66 dev vxlan$A dst 192.168.$i.2 self
    done
    hping3 192.168.10.2 -2 -d 60000

Splat looks like:
[  103.814237][ T1127] =============================================================================
[  103.871955][ T1127] BUG kmalloc-2k (Tainted: G    B            ): Padding overwritten. 0x00000000897a2e4f-0x000
[  103.873187][ T1127] -----------------------------------------------------------------------------
[  103.873187][ T1127]
[  103.874252][ T1127] INFO: Slab 0x000000005cccc724 objects=5 used=5 fp=0x0000000000000000 flags=0x10000000001020
[  103.881323][ T1127] CPU: 3 PID: 1127 Comm: hping3 Tainted: G    B             5.7.0+ #575
[  103.882131][ T1127] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[  103.883006][ T1127] Call Trace:
[  103.883324][ T1127]  dump_stack+0x96/0xdb
[  103.883716][ T1127]  slab_err+0xad/0xd0
[  103.884106][ T1127]  ? _raw_spin_unlock+0x1f/0x30
[  103.884620][ T1127]  ? get_partial_node.isra.78+0x140/0x360
[  103.885214][ T1127]  slab_pad_check.part.53+0xf7/0x160
[  103.885769][ T1127]  ? pskb_expand_head+0x110/0xe10
[  103.886316][ T1127]  check_slab+0x97/0xb0
[  103.886763][ T1127]  alloc_debug_processing+0x84/0x1a0
[  103.887308][ T1127]  ___slab_alloc+0x5a5/0x630
[  103.887765][ T1127]  ? pskb_expand_head+0x110/0xe10
[  103.888265][ T1127]  ? lock_downgrade+0x730/0x730
[  103.888762][ T1127]  ? pskb_expand_head+0x110/0xe10
[  103.889244][ T1127]  ? __slab_alloc+0x3e/0x80
[  103.889675][ T1127]  __slab_alloc+0x3e/0x80
[  103.890108][ T1127]  __kmalloc_node_track_caller+0xc7/0x420
[ ... ]

Fixes: 11a766ce915f ("net: Increase xmit RECURSION_LIMIT to 10.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix memleak in register_netdevice()

I got a memleak report when doing some fuzz test:

unreferenced object 0xffff888112584000 (size 13599):
  comm "ip", pid 3048, jiffies 4294911734 (age 343.491s)
  hex dump (first 32 bytes):
    74 61 70 30 00 00 00 00 00 00 00 00 00 00 00 00  tap0............
    00 ee d9 19 81 88 ff ff 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<000000002f60ba65>] __kmalloc_node+0x309/0x3a0
    [<0000000075b211ec>] kvmalloc_node+0x7f/0xc0
    [<00000000d3a97396>] alloc_netdev_mqs+0x76/0xfc0
    [<00000000609c3655>] __tun_chr_ioctl+0x1456/0x3d70
    [<000000001127ca24>] ksys_ioctl+0xe5/0x130
    [<00000000b7d5e66a>] __x64_sys_ioctl+0x6f/0xb0
    [<00000000e1023498>] do_syscall_64+0x56/0xa0
    [<000000009ec0eb12>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
unreferenced object 0xffff888111845cc0 (size 8):
  comm "ip", pid 3048, jiffies 4294911734 (age 343.491s)
  hex dump (first 8 bytes):
    74 61 70 30 00 88 ff ff                          tap0....
  backtrace:
    [<000000004c159777>] kstrdup+0x35/0x70
    [<00000000d8b496ad>] kstrdup_const+0x3d/0x50
    [<00000000494e884a>] kvasprintf_const+0xf1/0x180
    [<0000000097880a2b>] kobject_set_name_vargs+0x56/0x140
    [<000000008fbdfc7b>] dev_set_name+0xab/0xe0
    [<000000005b99e3b4>] netdev_register_kobject+0xc0/0x390
    [<00000000602704fe>] register_netdevice+0xb61/0x1250
    [<000000002b7ca244>] __tun_chr_ioctl+0x1cd1/0x3d70
    [<000000001127ca24>] ksys_ioctl+0xe5/0x130
    [<00000000b7d5e66a>] __x64_sys_ioctl+0x6f/0xb0
    [<00000000e1023498>] do_syscall_64+0x56/0xa0
    [<000000009ec0eb12>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
unreferenced object 0xffff88811886d800 (size 512):
  comm "ip", pid 3048, jiffies 4294911734 (age 343.491s)
  hex dump (first 32 bytes):
    00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00  .....N..........
    ff ff ff ff ff ff ff ff c0 66 3d a3 ff ff ff ff  .........f=.....
  backtrace:
    [<0000000050315800>] device_add+0x61e/0x1950
    [<0000000021008dfb>] netdev_register_kobject+0x17e/0x390
    [<00000000602704fe>] register_netdevice+0xb61/0x1250
    [<000000002b7ca244>] __tun_chr_ioctl+0x1cd1/0x3d70
    [<000000001127ca24>] ksys_ioctl+0xe5/0x130
    [<00000000b7d5e66a>] __x64_sys_ioctl+0x6f/0xb0
    [<00000000e1023498>] do_syscall_64+0x56/0xa0
    [<000000009ec0eb12>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

If call_netdevice_notifiers() failed, then rollback_registered()
calls netdev_unregister_kobject() which holds the kobject. The
reference cannot be put because the netdev won't be add to todo
list, so it will leads a memleak, we need put the reference to
avoid memleak.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: mvneta: Add 2500BaseX support for SoCs without comphy

The older SoCs like Armada XP support a 2500BaseX mode in the datasheets
referred to as DR-SGMII (Double rated SGMII) or HS-SGMII (High Speed
SGMII). This is an upclocked 1000BaseX mode, thus
PHY_INTERFACE_MODE_2500BASEX is the appropriate mode define for it.
adding support for it merely means writing the correct magic value into
the MVNETA_SERDES_CFG register.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: mvneta: Fix Serdes configuration for SoCs without comphy

The MVNETA_SERDES_CFG register is only available on older SoCs like the
Armada XP. On newer SoCs like the Armada 38x the fields are moved to
comphy. This patch moves the writes to this register next to the comphy
initialization, so that depending on the SoC either comphy or
MVNETA_SERDES_CFG is configured.
With this we no longer write to the MVNETA_SERDES_CFG on SoCs where it
doesn't exist.

Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: export features for vlans to use

Set up vlan_features for use by any vlans above us.

Fixes: beead698b173 ("ionic: Add the basic NDO callbacks for netdev support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic: no link check while resetting queues

If the driver is busy resetting queues after a change in
MTU or queue parameters, don't bother checking the link,
wait until the next watchdog cycle.

Fixes: 987c0871e8ae ("ionic: check for linkup in watchdog")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rxrpc: Fix afs large storage transmission performance drop

Commit 2ad6691d988c, which moved the modification of the status annotation
for a packet in the Tx buffer prior to the retransmission moved the state
clearance, but managed to lose the bit that set it to UNACK.

Consequently, if a retransmission occurs, the packet is accidentally
changed to the ACK state (ie. 0) by masking it off, which means that the
packet isn't counted towards the tally of newly-ACK'd packets if it gets
hard-ACK'd. This then prevents the congestion control algorithm from
recovering properly.

Fix by reinstating the change of state to UNACK.

Spotted by the generic/460 xfstest.

Fixes: 2ad6691d988c ("rxrpc: Fix race between incoming ACK parser and retransmitter")
Signed-off-by: David Howells <dhowells@redhat.com>

rxrpc: Fix handling of rwind from an ACK packet

The handling of the receive window size (rwind) from a received ACK packet
is not correct. The rxrpc_input_ackinfo() function currently checks the
current Tx window size against the rwind from the ACK to see if it has
changed, but then limits the rwind size before storing it in the tx_winsize
member and, if it increased, wake up the transmitting process. This means
that if rwind > RXRPC_RXTX_BUFF_SIZE - 1, this path will always be
followed.

Fix this by limiting rwind before we compare it to tx_winsize.

The effect of this can be seen by enabling the rxrpc_rx_rwind_change
tracepoint.

Fixes: 702f2ac87a9a ("rxrpc: Wake up the transmitter if Rx window size increases on the peer")
Signed-off-by: David Howells <dhowells@redhat.com>

net: usb: ax88179_178a: fix packet alignment padding

Using a AX88179 device (0b95:1790), I see two bytes of appended data on
every RX packet. For example, this 48-byte ping, using 0xff as a
payload byte:

  04:20:22.528472 IP 192.168.1.1 > 192.168.1.2: ICMP echo request, id 2447, seq 1, length 64
0x0000:  000a cd35 ea50 000a cd35 ea4f 0800 4500
0x0010:  0054 c116 4000 4001 f63e c0a8 0101 c0a8
0x0020:  0102 0800 b633 098f 0001 87ea cd5e 0000
0x0030:  0000 dcf2 0600 0000 0000 ffff ffff ffff
0x0040:  ffff ffff ffff ffff ffff ffff ffff ffff
0x0050:  ffff ffff ffff ffff ffff ffff ffff ffff
0x0060:  ffff 961f

Those last two bytes - 96 1f - aren't part of the original packet.

In the ax88179 RX path, the usbnet rx_fixup function trims a 2-byte
'alignment pseudo header' from the start of the packet, and sets the
length from a per-packet field populated by hardware. It looks like that
length field *includes* the 2-byte header; the current driver assumes
that it's excluded.

This change trims the 2-byte alignment header after we've set the packet
length, so the resulting packet length is correct. While we're moving
the comment around, this also fixes the spelling of 'pseudo'.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

rxrpc: Fix trace string

The trace symbol printer (__print_symbolic()) ignores symbols that map to
an empty string and prints the hex value instead.

Fix the symbol for rxrpc_cong_no_change to " -" instead of "" to avoid
this.

Fixes: b54a134a7de4 ("rxrpc: Fix handling of enums-to-string translation in tracing")
Signed-off-by: David Howells <dhowells@redhat.com>

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Alexei Starovoitov says:

====================
pull-request: bpf 2020-06-17

The following pull-request contains BPF updates for your *net* tree.

We've added 10 non-merge commits during the last 2 day(s) which contain
a total of 14 files changed, 158 insertions(+), 59 deletions(-).

The main changes are:

1) Important fix for bpf_probe_read_kernel_str() return value, from Andrii.

2) [gs]etsockopt fix for large optlen, from Stanislav.

3) devmap allocation fix, from Toke.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: Document optval > PAGE_SIZE behavior for sockopt hooks

Extend existing doc with more details about requiring ctx->optlen = 0
for handling optval > PAGE_SIZE.

Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200617010416.93086-3-sdf@google.com

selftests/bpf: Make sure optvals > PAGE_SIZE are bypassed

We are relying on the fact, that we can pass > sizeof(int) optvals
to the SOL_IP+IP_FREEBIND option (the kernel will take first 4 bytes).
In the BPF program we check that we can only touch PAGE_SIZE bytes,
but the real optlen is PAGE_SIZE * 2. In both cases, we override it to
some predefined value and trim the optlen.

Also, let's modify exiting IP_TOS usecase to test optlen=0 case
where BPF program just bypasses the data as is.

Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200617010416.93086-2-sdf@google.com

bpf: Don't return EINVAL from {get,set}sockopt when optlen > PAGE_SIZE

Attaching to these hooks can break iptables because its optval is
usually quite big, or at least bigger than the current PAGE_SIZE limit.
David also mentioned some SCTP options can be big (around 256k).

For such optvals we expose only the first PAGE_SIZE bytes to
the BPF program. BPF program has two options:
1. Set ctx->optlen to 0 to indicate that the BPF's optval
   should be ignored and the kernel should use original userspace
   value.
2. Set ctx->optlen to something that's smaller than the PAGE_SIZE.

v5:
* use ctx->optlen == 0 with trimmed buffer (Alexei Starovoitov)
* update the docs accordingly

v4:
* use temporary buffer to avoid optval == optval_end == NULL;
  this removes the corner case in the verifier that might assume
  non-zero PTR_TO_PACKET/PTR_TO_PACKET_END.

v3:
* don't increase the limit, bypass the argument

v2:
* proper comments formatting (Jakub Kicinski)

Fixes: 0d01da6afc54 ("bpf: implement getsockopt and setsockopt hooks")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Link: https://lore.kernel.org/bpf/20200617010416.93086-1-sdf@google.com

devmap: Use bpf_map_area_alloc() for allocating hash buckets

Syzkaller discovered that creating a hash of type devmap_hash with a large
number of entries can hit the memory allocator limit for allocating
contiguous memory regions. There's really no reason to use kmalloc_array()
directly in the devmap code, so just switch it to the existing
bpf_map_area_alloc() function that is used elsewhere.

Fixes: 6f9d451ab1a3 ("xdp: Add devmap_hash map type for looking up devices by hashed index")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200616142829.114173-1-toke@redhat.com

xdp: Handle frame_sz in xdp_convert_zc_to_xdp_frame()

In commit 34cc0b338a61 we only handled the frame_sz in convert_to_xdp_frame().
This patch will also handle frame_sz in xdp_convert_zc_to_xdp_frame().

Fixes: 34cc0b338a61 ("xdp: Xdp_frame add member frame_sz and handle in convert_to_xdp_frame")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200616103518.2963410-1-liuhangbin@gmail.com

tools, bpftool: Add ringbuf map type to map command docs

Commit c34a06c56df7 ("tools/bpftool: Add ringbuf map to a list of known
map types") added the symbolic "ringbuf" name. Document it in the bpftool
map command docs and usage as well.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200616113303.8123-1-tklauser@distanz.ch

bpf: bpf_probe_read_kernel_str() has to return amount of data read on success

During recent refactorings, bpf_probe_read_kernel_str() started returning 0 on
success, instead of amount of data successfully read. This majorly breaks
applications relying on bpf_probe_read_kernel_str() and bpf_probe_read_str()
and their results. Fix this by returning actual number of bytes read.

Fixes: 8d92db5c04d1 ("bpf: rework the compat kernel probe handling")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200616050432.1902042-1-andriin@fb.com

Merge git://git./linux/kernel/git/netdev/net

Pull networking fixes from David Miller:

1) Don't get per-cpu pointer with preemption enabled in nft_set_pipapo,
    fix from Stefano Brivio.

2) Fix memory leak in ctnetlink, from Pablo Neira Ayuso.

3) Multiple definitions of MPTCP_PM_MAX_ADDR, from Geliang Tang.

4) Accidently disabling NAPI in non-error paths of macb_open(), from
    Charles Keepax.

5) Fix races between alx_stop and alx_remove, from Zekun Shen.

6) We forget to re-enable SRIOV during resume in bnxt_en driver, from
    Michael Chan.

7) Fix memory leak in ipv6_mc_destroy_dev(), from Wang Hai.

8) rxtx stats use wrong index in mvpp2 driver, from Sven Auhagen.

9) Fix memory leak in mptcp_subflow_create_socket error path, from Wei
    Yongjun.

10) We should not adjust the TCP window advertised when sending dup acks
    in non-SACK mode, because it won't be counted as a dup by the sender
    if the window size changes. From Eric Dumazet.

11) Destroy the right number of queues during remove in mvpp2 driver,
    from Sven Auhagen.

12) Various WOL and PM fixes to e1000 driver, from Chen Yu, Vaibhav
    Gupta, and Arnd Bergmann.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (35 commits)
  e1000e: fix unused-function warning
  e1000: use generic power management
  e1000e: Do not wake up the system via WOL if device wakeup is disabled
  lan743x: add MODULE_DEVICE_TABLE for module loading alias
  mlxsw: spectrum: Adjust headroom buffers for 8x ports
  bareudp: Fixed configuration to avoid having garbage values
  mvpp2: remove module bugfix
  tcp: grow window for OOO packets only for SACK flows
  mptcp: fix memory leak in mptcp_subflow_create_socket()
  netfilter: flowtable: Make nf_flow_table_offload_add/del_cb inline
  net/sched: act_ct: Make tcf_ct_flow_table_restore_skb inline
  net: dsa: sja1105: fix PTP timestamping with large tc-taprio cycles
  mvpp2: ethtool rxtx stats fix
  MAINTAINERS: switch to my private email for Renesas Ethernet drivers
  rocker: fix incorrect error handling in dma_rings_init
  test_objagg: Fix potential memory leak in error handling
  net: ethernet: mtk-star-emac: simplify interrupt handling
  mld: fix memory leak in ipv6_mc_destroy_dev()
  bnxt_en: Return from timer if interface is not in open state.
  bnxt_en: Fix AER reset logic on 57500 chips.
  ...

Merge tag 'afs-fixes-20200616' of git://git./linux/kernel/git/dhowells/linux-fs

Pull AFS fixes from David Howells:
"I've managed to get xfstests kind of working with afs. Here are a set
  of patches that fix most of the bugs found.

  There are a number of primary issues:

   - Incorrect handling of mtime and non-handling of ctime. It might be
     argued, that the latter isn't a bug since the AFS protocol doesn't
     support ctime, but I should probably still update it locally.

   - Shared-write mmap, truncate and writeback bugs. This includes not
     changing i_size under the callback lock, overwriting local i_size
     with the reply from the server after a partial writeback, not
     limiting the writeback from an mmapped page to EOF.

   - Checks for an abort code indicating that the primary vnode in an
     operation was deleted by a third-party are done in the wrong place.

   - Silly rename bugs. This includes an incomplete conversion to the
     new operation handling, duplicate nlink handling, nlink changing
     not being done inside the callback lock and insufficient handling
     of third-party conflicting directory changes.

  And some secondary ones:

   - The UAEOVERFLOW abort code should map to EOVERFLOW not EREMOTEIO.

   - Remove a couple of unused or incompletely used bits.

   - Remove a couple of redundant success checks.

  These seem to fix all the data-corruption bugs found by

./check -afs -g quick

  along with the obvious silly rename bugs and time bugs.

  There are still some test failures, but they seem to fall into two
  classes: firstly, the authentication/security model is different to
  the standard UNIX model and permission is arbitrated by the server and
  cached locally; and secondly, there are a number of features that AFS
  does not support (such as mknod). But in these cases, the tests
  themselves need to be adapted or skipped.

  Using the in-kernel afs client with xfstests also found a bug in the
  AuriStor AFS server that has been fixed for a future release"

* tag 'afs-fixes-20200616' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Fix silly rename
  afs: afs_vnode_commit_status() doesn't need to check the RPC error
  afs: Fix use of afs_check_for_remote_deletion()
  afs: Remove afs_operation::abort_code
  afs: Fix yfs_fs_fetch_status() to honour vnode selector
  afs: Remove yfs_fs_fetch_file_status() as it's not used
  afs: Fix the mapping of the UAEOVERFLOW abort code
  afs: Fix truncation issues and mmap writeback size
  afs: Concoct ctimes
  afs: Fix EOF corruption
  afs: afs_write_end() should change i_size under the right lock
  afs: Fix non-setting of mtime when writing into mmap

Documentation: remove SH-5 index entries

Remove SH-5 documentation index entries following the removal
of SH-5 source code.

Error: Cannot open file ../arch/sh/mm/tlb-sh5.c
Error: Cannot open file ../arch/sh/mm/tlb-sh5.c
Error: Cannot open file ../arch/sh/include/asm/tlb_64.h
Error: Cannot open file ../arch/sh/include/asm/tlb_64.h

Fixes: 3b69e8b45711 ("Merge tag 'sh-for-5.8' of git://git.libc.org/linux-sh")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Rich Felker <dalias@libc.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: ysato@users.sourceforge.jp
Cc: linux-sh@vger.kernel.org
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'flex-array-conversions-5.8-rc2' of git://git./linux/kernel/git/gustavoars/linux

Pull flexible-array member conversions from Gustavo A. R. Silva:
"Replace zero-length arrays with flexible-array members.

  Notice that all of these patches have been baking in linux-next for
  two development cycles now.

  There is a regular need in the kernel to provide a way to declare
  having a dynamically sized set of trailing elements in a structure.
  Kernel code should always use “flexible array members”[1] for these
  cases. The older style of one-element or zero-length arrays should no
  longer be used[2].

  C99 introduced “flexible array members”, which lacks a numeric size
  for the array declaration entirely:

        struct something {
                size_t count;
                struct foo items[];
        };

  This is the way the kernel expects dynamically sized trailing elements
  to be declared. It allows the compiler to generate errors when the
  flexible array does not occur last in the structure, which helps to
  prevent some kind of undefined behavior[3] bugs from being
  inadvertently introduced to the codebase.

  It also allows the compiler to correctly analyze array sizes (via
  sizeof(), CONFIG_FORTIFY_SOURCE, and CONFIG_UBSAN_BOUNDS). For
  instance, there is no mechanism that warns us that the following
  application of the sizeof() operator to a zero-length array always
  results in zero:

        struct something {
                size_t count;
                struct foo items[0];
        };

        struct something *instance;

        instance = kmalloc(struct_size(instance, items, count), GFP_KERNEL);
        instance->count = count;

        size = sizeof(instance->items) * instance->count;
        memcpy(instance->items, source, size);

  At the last line of code above, size turns out to be zero, when one
  might have thought it represents the total size in bytes of the
  dynamic memory recently allocated for the trailing array items. Here
  are a couple examples of this issue[4][5].

  Instead, flexible array members have incomplete type, and so the
  sizeof() operator may not be applied[6], so any misuse of such
  operators will be immediately noticed at build time.

  The cleanest and least error-prone way to implement this is through
  the use of a flexible array member:

        struct something {
                size_t count;
                struct foo items[];
        };

        struct something *instance;

        instance = kmalloc(struct_size(instance, items, count), GFP_KERNEL);
        instance->count = count;

        size = sizeof(instance->items[0]) * instance->count;
        memcpy(instance->items, source, size);

  instead"

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
[4] commit f2cd32a443da ("rndis_wlan: Remove logically dead code")
[5] commit ab91c2a89f86 ("tpm: eventlog: Replace zero-length array with flexible-array member")
[6] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html

* tag 'flex-array-conversions-5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (41 commits)
  w1: Replace zero-length array with flexible-array
  tracing/probe: Replace zero-length array with flexible-array
  soc: ti: Replace zero-length array with flexible-array
  tifm: Replace zero-length array with flexible-array
  dmaengine: tegra-apb: Replace zero-length array with flexible-array
  stm class: Replace zero-length array with flexible-array
  Squashfs: Replace zero-length array with flexible-array
  ASoC: SOF: Replace zero-length array with flexible-array
  ima: Replace zero-length array with flexible-array
  sctp: Replace zero-length array with flexible-array
  phy: samsung: Replace zero-length array with flexible-array
  RxRPC: Replace zero-length array with flexible-array
  rapidio: Replace zero-length array with flexible-array
  media: pwc: Replace zero-length array with flexible-array
  firmware: pcdp: Replace zero-length array with flexible-array
  oprofile: Replace zero-length array with flexible-array
  block: Replace zero-length array with flexible-array
  tools/testing/nvdimm: Replace zero-length array with flexible-array
  libata: Replace zero-length array with flexible-array
  kprobes: Replace zero-length array with flexible-array
  ...

x86/purgatory: Add -fno-stack-protector

The purgatory Makefile removes -fstack-protector options if they were
configured in, but does not currently add -fno-stack-protector.

If gcc was configured with the --enable-default-ssp configure option,
this results in the stack protector still being enabled for the
purgatory (absent distro-specific specs files that might disable it
again for freestanding compilations), if the main kernel is being
compiled with stack protection enabled (if it's disabled for the main
kernel, the top-level Makefile will add -fno-stack-protector).

This will break the build since commit
e4160b2e4b02 ("x86/purgatory: Fail the build if purgatory.ro has missing symbols")
and prior to that would have caused runtime failure when trying to use
kexec.

Explicitly add -fno-stack-protector to avoid this, as done in other
Makefiles that need to disable the stack protector.

Reported-by: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch '1GbE' of git://git./linux/kernel/git/jkirsher/net-queue

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2020-06-16

This series contains fixes to e1000 and e1000e.

Chen fixes an e1000e issue where systems could be waken via WoL, even
though the user has disabled the wakeup bit via sysfs.

Vaibhav Gupta updates the e1000 driver to clean up the legacy Power
Management hooks.

Arnd Bergmann cleans up the inconsistent use CONFIG_PM_SLEEP
preprocessor tags, which also resolves the compiler warnings about the
possibility of unused structure.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: fix unused-function warning

The CONFIG_PM_SLEEP #ifdef checks in this file are inconsistent,
leading to a warning about sometimes unused function:

drivers/net/ethernet/intel/e1000e/netdev.c:137:13: error: unused function 'e1000e_check_me' [-Werror,-Wunused-function]

Rather than adding more #ifdefs, just remove them completely
and mark the PM functions as __maybe_unused to let the compiler
work it out on it own.

Fixes: e086ba2fccda ("e1000e: disable s0ix entry and exit flows for ME systems")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000: use generic power management

With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let PCI
core handle the work.

e1000_suspend() calls __e1000_shutdown() to perform intermediate tasks.
__e1000_shutdown() modifies the value of "wake" (device should be wakeup
enabled or not), responsible for controlling the flow of legacy PM.

Since, PCI core has no idea about the value of "wake", new code for generic
PM may produce unexpected results. Thus, use "device_set_wakeup_enable()"
to wakeup-enable the device accordingly.

Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e: Do not wake up the system via WOL if device wakeup is disabled

Currently the system will be woken up via WOL(Wake On LAN) even if the
device wakeup ability has been disabled via sysfs:
cat /sys/devices/pci0000:00/0000:00:1f.6/power/wakeup
disabled

The system should not be woken up if the user has explicitly
disabled the wake up ability for this device.

This patch clears the WOL ability of this network device if the
user has disabled the wake up ability in sysfs.

Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver")
Reported-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

lan743x: add MODULE_DEVICE_TABLE for module loading alias

Without a MODULE_DEVICE_TABLE the attributes are missing that create
an alias for auto-loading the module in userspace via hotplug.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

afs: Fix silly rename

Fix AFS's silly rename by the following means:

(1) Set the destination directory in afs_do_silly_rename() so as to avoid
     misbehaviour and indicate that the directory data version will
     increment by 1 so as to avoid warnings about unexpected changes in the
     DV.  Also indicate that the ctime should be updated to avoid xfstest
     grumbling.

(2) Note when the server indicates that a directory changed more than we
     expected (AFS_OPERATION_DIR_CONFLICT), indicating a conflict with a
     third party change, checking on successful completion of unlink and
     rename.

     The problem is that the FS.RemoveFile RPC op doesn't report the status
     of the unlinked file, though YFS.RemoveFile2 does.  This can be
     mitigated by the assumption that if the directory DV cranked by
     exactly 1, we can be sure we removed one link from the file; further,
     ordinarily in AFS, files cannot be hardlinked across directories, so
     if we reduce nlink to 0, the file is deleted.

     However, if the directory DV jumps by more than 1, we cannot know if a
     third party intervened by adding or removing a link on the file we
     just removed a link from.

     The same also goes for any vnode that is at the destination of the
     FS.Rename RPC op.

(3) Make afs_vnode_commit_status() apply the nlink drop inside the cb_lock
     section along with the other attribute updates if ->op_unlinked is set
     on the descriptor for the appropriate vnode.

(4) Issue a follow up status fetch to the unlinked file in the event of a
     third party conflict that makes it impossible for us to know if we
     actually deleted the file or not.

(5) Provide a flag, AFS_VNODE_SILLY_DELETED, to make afs_getattr() lie to
     the user about the nlink of a silly deleted file so that it appears as
     0, not 1.

Found with the generic/035 and generic/084 xfstests.

Fixes: e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>

mlxsw: spectrum: Adjust headroom buffers for 8x ports

The port's headroom buffers are used to store packets while they
traverse the device's pipeline and also to store packets that are egress
mirrored.

On Spectrum-3, ports with eight lanes use two headroom buffers between
which the configured headroom size is split.

In order to prevent packet loss, multiply the calculated headroom size
by two for 8x ports.

Fixes: da382875c616 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bareudp: Fixed configuration to avoid having garbage values

Code to initialize the conf structure while gathering the configuration
of the device was missing.

Fixes: 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Martin <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mvpp2: remove module bugfix

The remove function does not destroy all
BM Pools when per cpu pool is active.

When reloading the mvpp2 as a module the BM Pools
are still active in hardware and due to the bug
have twice the size now old + new.

This eventually leads to a kernel crash.

v2:
* add Fixes tag

Fixes: 7d04b0b13b11 ("mvpp2: percpu buffers")
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: grow window for OOO packets only for SACK flows

Back in 2013, we made a change that broke fast retransmit
for non SACK flows.

Indeed, for these flows, a sender needs to receive three duplicate
ACK before starting fast retransmit. Sending ACK with different
receive window do not count.

Even if enabling SACK is strongly recommended these days,
there still are some cases where it has to be disabled.

Not increasing the window seems better than having to
rely on RTO.

After the fix, following packetdrill test gives :

// Initialize connection
    0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

   +0 < S 0:0(0) win 32792 <mss 1000,nop,wscale 7>
   +0 > S. 0:0(0) ack 1 <mss 1460,nop,wscale 8>
   +0 < . 1:1(0) ack 1 win 514

   +0 accept(3, ..., ...) = 4

   +0 < . 1:1001(1000) ack 1 win 514
// Quick ack
   +0 > . 1:1(0) ack 1001 win 264

   +0 < . 2001:3001(1000) ack 1 win 514
// DUPACK : Normally we should not change the window
   +0 > . 1:1(0) ack 1001 win 264

   +0 < . 3001:4001(1000) ack 1 win 514
// DUPACK : Normally we should not change the window
   +0 > . 1:1(0) ack 1001 win 264

   +0 < . 4001:5001(1000) ack 1 win 514
// DUPACK : Normally we should not change the window
    +0 > . 1:1(0) ack 1001 win 264

   +0 < . 1001:2001(1000) ack 1 win 514
// Hole is repaired.
   +0 > . 1:1(0) ack 5001 win 272

Fixes: 4e4f1fc22681 ("tcp: properly increase rcv_ssthresh for ofo packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mfd-fixes-5.8' of git://git./linux/kernel/git/lee/mfd

Pull MFD fix from Lee Jones:
"Fix NULL pointer dereference in mt6360 driver"

* tag 'mfd-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: mt6360: Fix register driver NULL pointer by adding driver name

afs: afs_vnode_commit_status() doesn't need to check the RPC error

afs_vnode_commit_status() is only ever called if op->error is 0, so remove
the op->error checks from the function.

Fixes: e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept")
Signed-off-by: David Howells <dhowells@redhat.com>

afs: Fix use of afs_check_for_remote_deletion()

afs_check_for_remote_deletion() checks to see if error ENOENT is returned
by the server in response to an operation and, if so, marks the primary
vnode as having been deleted as the FID is no longer valid.

However, it's being called from the operation success functions, where no
abort has happened - and if an inline abort is recorded, it's handled by
afs_vnode_commit_status().

Fix this by actually calling the operation aborted method if provided and
having that point to afs_check_for_remote_deletion().

Fixes: e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept")
Signed-off-by: David Howells <dhowells@redhat.com>

afs: Remove afs_operation::abort_code

Remove afs_operation::abort_code as it's read but never set. Use
ac.abort_code instead.

Signed-off-by: David Howells <dhowells@redhat.com>

afs: Fix yfs_fs_fetch_status() to honour vnode selector

Fix yfs_fs_fetch_status() to honour the vnode selector in
op->fetch_status.which as does afs_fs_fetch_status() that allows
afs_do_lookup() to use this as an alternative to the InlineBulkStatus RPC
call if not implemented by the server.

This doesn't matter in the current code as YFS servers always implement
InlineBulkStatus, but a subsequent will call it on YFS servers too in some
circumstances.

Fixes: e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept")
Signed-off-by: David Howells <dhowells@redhat.com>

afs: Remove yfs_fs_fetch_file_status() as it's not used

Remove yfs_fs_fetch_file_status() as it's no longer used.

Signed-off-by: David Howells <dhowells@redhat.com>

bpf, xdp, samples: Fix null pointer dereference in *_user code

Memset on the pointer right after malloc can cause a NULL pointer
deference if it failed to allocate memory. A simple fix is to
replace malloc()/memset() pair with a simple call to calloc().

Fixes: 0fca931a6f21 ("samples/bpf: program demonstrating access to xdp_rxq_info")
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>

mfd: mt6360: Fix register driver NULL pointer by adding driver name

The driver name was accidentally removed when .probe() by was replaced
by .probe_new() during an early patch review.

[  121.243012] EAX: c2a8bc64 EBX: 00000000 ECX: 00000000 EDX: 00000000
[  121.243012] ESI: c2a8bc79 EDI: 00000000 EBP: e54bdea8 ESP: e54bdea0
[  121.243012] DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068 EFLAGS: 00010286
[  121.243012] CR0: 80050033 CR2: 00000000 CR3: 02ec3000 CR4: 000006b0
[  121.243012] Call Trace:
[  121.243012]  kset_find_obj+0x3d/0xc0
[  121.243012]  driver_find+0x16/0x40
[  121.243012]  driver_register+0x49/0x100
[  121.243012]  ? i2c_for_each_dev+0x39/0x50
[  121.243012]  ? __process_new_adapter+0x20/0x20
[  121.243012]  ? cht_wc_driver_init+0x11/0x11
[  121.243012]  i2c_register_driver+0x30/0x80
[  121.243012]  ? intel_lpss_pci_driver_init+0x16/0x16
[  121.243012]  mt6360_pmu_driver_init+0xf/0x11
[  121.243012]  do_one_initcall+0x33/0x1a0
[  121.243012]  ? parse_args+0x1eb/0x3d0
[  121.243012]  ? __might_sleep+0x31/0x90
[  121.243012]  ? kernel_init_freeable+0x10a/0x17f
[  121.243012]  kernel_init_freeable+0x12c/0x17f
[  121.243012]  ? rest_init+0x110/0x110
[  121.243012]  kernel_init+0xb/0x100
[  121.243012]  ? schedule_tail_wrapper+0x9/0xc
[  121.243012]  ret_from_fork+0x19/0x24
[  121.243012] Modules linked in:
[  121.243012] CR2: 0000000000000000
[  121.243012] random: get_random_bytes called from init_oops_id+0x3a/0x40 with crng_init=0
[  121.243012] ---[ end trace 38a803400f1a2bee ]---
[  121.243012] EIP: strcmp+0x11/0x30

Fixes: 7edd363421dab ("mfd: Add support for PMIC MT6360")
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@kernel.org>
[Lee: Taking the opportunity to fix the compatible string too 's/_/-/']
Signed-off-by: Lee Jones <lee.jones@linaro.org>

w1: Replace zero-length array with flexible-array

There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

tracing/probe: Replace zero-length array with flexible-array

There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

soc: ti: Replace zero-length array with flexible-array

There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

tifm: Replace zero-length array with flexible-array

There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

dmaengine: tegra-apb: Replace zero-length array with flexible-array

There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>