dt-bindings: serial: stm32: override FIFO threshold properties

Override rx-threshold and tx-threshold properties:
- extend description
- provide default and expected values

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Changes in v2:
Change added properties naming and factorize it in serial.yaml as proposed
by Rob Herring.

Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210413174015.23011-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: serial: add RX and TX FIFO properties

Add two optional DT properties to configure RX and TX FIFO thresholds:
- rx-threshold
- tx-threshold

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210413174015.23011-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: xilinx_uartps: drop low-latency workaround

Commit c8dbdc842d30 ("serial: xuartps: Rewrite the interrupt handling
logic") reworked the driver interrupt processing but also, without
comment, added an unnecessary workaround for the infamous low_latency
behaviour of tty_flip_buffer_push() which had been removed years
before.

Specifically, since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-27-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: vt8500: drop low-latency workaround

Commit de49df58366f ("tty: serial: vt8500: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-26-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: timbuart: drop low-latency workaround

The timbuart driver has always carried a workaround for the infamous
low_latency behaviour of tty_flip_buffer_push() which required not
holding the port lock when the low_latency flag was set.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-25-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: sunsu: drop low-latency workaround

The sunsu driver has been carrying a workaround for the infamous
low_latency behaviour of tty_flip_buffer_push() by dropping and
reacquiring the port lock in the interrupt handler since 2004.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-24-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: sifive: drop low-latency workaround

The sifive driver has always carried an unnecessary workaround for the
infamous low_latency behaviour of tty_flip_buffer_push() which had been
removed years before the driver was added by commit 45c054d0815b ("tty:
serial: add driver for the SiFive UART").

Specifically, since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-23-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: txx9: drop low-latency workaround

Commit f5ee56cc184e ("[PATCH] txx9 serial update") worked around the
infamous low_latency behaviour of tty_flip_buffer_push() by simply
dropping and reacquiring the port lock in the interrupt handler.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-22-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: sa1100: drop low-latency workaround

Commit 53e0e6706c76 ("tty: serial: sa1100: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-21-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: rp2: drop low-latency workaround

Commit de7053c77123 ("tty: serial: rp2: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-20-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: rda: drop low-latency workaround

The rda driver has always carried an unnecessary workaround for the
infamous low_latency behaviour of tty_flip_buffer_push(), which had
been removed years before the driver was added by commit c10b13325ced
("tty: serial: Add RDA8810PL UART driver").

Specifically, since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-19-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: owl: drop low-latency workaround

The owl driver has always carried an unnecessary workaround for the
infamous low_latency behaviour of tty_flip_buffer_push(), which had
been removed years before the driver was added by commit fc60a8b675bd
("tty: serial: owl: Implement console driver").

Specifically, since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-18-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: msm_serial: drop low-latency workaround

Commit f77232dab25b ("tty: serial: msm: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-17-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: mpc52xx_uart: drop low-latency workaround

Commit fbe543b412ce ("Fix a potential issue in mpc52xx uart driver")
worked around the infamous low_latency behaviour of
tty_flip_buffer_push() by simply dropping and reacquiring the port lock
in the interrupt handler.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-16-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: meson: drop low-latency workaround

The meson driver has always carried an unnecessary workaround for the
infamous low_latency behaviour of tty_flip_buffer_push(), which had
already been removed by the time the driver was added by commit
ff7693d079e5 ("ARM: meson: serial: add MesonX SoC on-chip uart driver").

Specifically, since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-15-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: mcf: drop low-latency workaround

Commit 5275ad70fed3 ("tty: serial: mcf: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-14-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: lpc32xx_hs: drop low-latency workaround

Commit ec128510905c ("tty: serial: lpc32xx_hs: drop uart_port->lock
before calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-13-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: icom: drop low-latency workaround

Commit 5faf75d7fed2 ("tty: serial: icom: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-12-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: bcm63xx: drop low-latency workaround

Commit b4d499241c34 ("tty: serial: bcm63xx: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-11-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: atmel_serial: drop low-latency workaround

Commit 1ecc26bd2789 ("atmel_serial: split the interrupt handler") worked
around the infamous low_latency behaviour of tty_flip_buffer_push() by
dropping and reacquiring the port lock in the tasklet callback.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Cc: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-10-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: arc_uart: drop low-latency workaround

Commit 3fa1200851c7 ("tty: serial: arc: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: ar933x: drop low-latency workaround

Commit b16c8e3eed12 ("tty: serial: ar933x: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: apbuart: drop low-latency workaround

Commit 78d34d75c84d ("tty: serial: apbuart: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: amba-pl011: drop low-latency workaround

Commit ead76f329f77 ("ARM: 6763/1: pl011: add optional RX DMA to PL011
v2") added RX DMA support and also reproduced the workaround for the
infamous low_latency behaviour of tty_flip_buffer_push() by dropping and
reacquiring the port lock during receive processing.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Note that the port lock is also dropped in the PIO path
(see pl011_rx_chars), but it is not clear whether this is still needed
by the DMA code added by the aforementioned commit.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: amba-pl010: drop low-latency workaround

Commit 2389b272168c ("[ARM] 4417/1: Serial: Fix AMBA drivers locking")
worked around the infamous low_latency behaviour of
tty_flip_buffer_push() by simply dropping and reacquiring the port lock
in the interrupt handler.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: altera_uart: drop low-latency workaround

Commit dd085ed8ef6c ("tty: serial: altera: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: altera_jtaguart: drop low-latency workaround

Commit 53dd0ba7a6f4 ("tty: serial: altera_jtag: drop uart_port->lock
before calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.

Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.

The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.

Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: mxser: drop low-latency workaround

Commit 67d2bc58afdd ("Char: mxser_new, fix recursive locking") worked
around the infamous low_latency behaviour of tty_flip_buffer_push() by
simply dropping and reacquiring the port lock in the interrupt handler.

Since commit a9c3f68f3cd8 ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.

Link: https://lore.kernel.org/lkml/3018694794025219@wsc.cz/T/#m06b04c640a7b6f41afb3d34a4cf29b1df4935d3a
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: omap: fix rs485 half-duplex filtering

Data received during half-duplex transmission must be filtered.
If the target device responds quickly, emptying the FIFO at the end of
the transmission can erase not only the echo characters but also part of
the response message.
By keeping the receive interrupt enabled even during transmission, it
allows you to filter each echo character and only in a number equal to
those transmitted.
The issue was generated by a target device that started responding
240us later having received a request in communication at 115200bps.
Sometimes, some messages received by the target were missing some of the
first bytes.

Fixes: 3a13884abea0 ("tty/serial: omap: empty the RX FIFO at the end of half-duplex TX")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20210418094705.27014-1-dariobin@libero.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: omap: don't disable rs485 if rts gpio is missing

There are rs485 transceivers (e.g. MAX13487E/MAX13488E) which
automatically disable or enable the driver and receiver to keep the bus
in the correct state.
In these cases we don't need a GPIO for flow control.

Fixes: 4a0ac0f55b18 ("OMAP: add RS485 support")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20210415210945.25863-1-dariobin@libero.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: stm32: defer sysrq processing

Use the uart_unlock_and_check_sysrq() helper to defer sysrq processing
until receive processing is done and the port lock has been released.

This allows cleaning up the console_write() implementation by not having
to work around the recursive sysrq case (by dropping locking completely)
and also makes the console code work with PREEMPT_RT by no longer
relying on local_irq_save().

Reviewed-by: Valentin Caron<valentin.caron@foss.st.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210416140557.25177-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: stm32: fix threaded interrupt handling

When DMA is enabled the receive handler runs in a threaded handler, but
the primary handler up until very recently neither disabled interrupts
in the device or used IRQF_ONESHOT. This would lead to a deadlock if an
interrupt comes in while the threaded receive handler is running under
the port lock.

Commit ad7676812437 ("serial: stm32: fix a deadlock condition with
wakeup event") claimed to fix an unrelated deadlock, but unfortunately
also disabled interrupts in the threaded handler. While this prevents
the deadlock mentioned in the previous paragraph it also defeats the
purpose of using a threaded handler in the first place.

Fix this by making the interrupt one-shot and not disabling interrupts
in the threaded handler.

Note that (receive) DMA must not be used for a console port as the
threaded handler could be interrupted while holding the port lock,
something which could lead to a deadlock in case an interrupt handler
ends up calling printk.

Fixes: ad7676812437 ("serial: stm32: fix a deadlock condition with wakeup event")
Fixes: 3489187204eb ("serial: stm32: adding dma support")
Cc: stable@vger.kernel.org # 4.9
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Gerald Baeza <gerald.baeza@st.com>
Reviewed-by: Valentin Caron<valentin.caron@foss.st.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210416140557.25177-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: do not restore interrupt state in sysrq helper

The uart_unlock_and_check_sysrq() helper can be used to defer processing
of sysrq until the interrupt handler has released the port lock and is
about to return.

Since commit 81e2073c175b ("genirq: Disable interrupts for force
threaded handlers") interrupt handlers that are not explicitly requested
as threaded are always called with interrupts disabled and there is no
need to save the interrupt state when taking the port lock.

Instead of adding another sysrq helper for when the interrupt state has
not needlessly been saved, drop the state parameter from
uart_unlock_and_check_sysrq() and update its callers to no longer
explicitly disable interrupts in their interrupt handlers.

Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210416140557.25177-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: synclink_gt: remove redundant initialization of variable count

The variable count is being initialized with a value that is
never read and it is being updated later with a new value.  The
initialization is redundant and can be removed.

Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210420105718.377086-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ttyprintk: Add TTY hangup callback.

syzbot is reporting hung task due to flood of

  tty_warn(tty, "%s: tty->count = 1 port count = %d\n", __func__,
           port->count);

message [1], for ioctl(TIOCVHANGUP) prevents tty_port_close() from
decrementing port->count due to tty_hung_up_p() == true.

----------
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <sys/ioctl.h>
#include <unistd.h>

int main(int argc, char *argv[])
{
int i;
int fd[10];

for (i = 0; i < 10; i++)
fd[i] = open("/dev/ttyprintk", O_WRONLY);
ioctl(fd[0], TIOCVHANGUP);
for (i = 0; i < 10; i++)
close(fd[i]);
close(open("/dev/ttyprintk", O_WRONLY));
return 0;
}
----------

When TTY hangup happens, port->count needs to be reset via
"struct tty_operations"->hangup callback.

[1] https://syzkaller.appspot.com/bug?id=39ea6caa479af471183997376dc7e90bc7d64a6a

Reported-by: syzbot <syzbot+43e93968b964e369db0b@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+3ed715090790806d8b18@syzkaller.appspotmail.com>
Tested-by: syzbot <syzbot+43e93968b964e369db0b@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 24b4b67d17c308aa ("add ttyprintk driver")
Link: https://lore.kernel.org/r/17e0652d-89b7-c8c0-fb53-e7566ac9add4@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: core: Do core softreset when switch mode

From: John Stultz <john.stultz@linaro.org>

According to the programming guide, to switch mode for DRD controller,
the driver needs to do the following.

To switch from device to host:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(host mode)
3. Reset the host with USBCMD.HCRESET
4. Then follow up with the initializing host registers sequence

To switch from host to device:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(device mode)
3. Reset the device with DCTL.CSftRst
4. Then follow up with the initializing registers sequence

Currently we're missing step 1) to do GCTL.CoreSoftReset and step 3) of
switching from host to device. John Stult reported a lockup issue seen
with HiKey960 platform without these steps[1]. Similar issue is observed
with Ferry's testing platform[2].

So, apply the required steps along with some fixes to Yu Chen's and John
Stultz's version. The main fixes to their versions are the missing wait
for clocks synchronization before clearing GCTL.CoreSoftReset and only
apply DCTL.CSftRst when switching from host to device.

[1] https://lore.kernel.org/linux-usb/20210108015115.27920-1-john.stultz@linaro.org/
[2] https://lore.kernel.org/linux-usb/0ba7a6ba-e6a7-9cd4-0695-64fc927e01f1@gmail.com/

Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Ferry Toth <fntoth@gmail.com>
Cc: Wesley Cheng <wcheng@codeaurora.org>
Cc: <stable@vger.kernel.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Wesley Cheng <wcheng@codeaurora.org>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/374440f8dcd4f06c02c2caf4b1efde86774e02d9.1618521663.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Get rid of useless error checks in suspend interrupt

Squashed from Douglas Anderson's suggested commit
"usb: dwc2: Get rid of useless error checks for
hibernation/partial power down"

 - After this commit there should never be any
case where dwc2_enter_partial_power_down() and
dwc2_enter_hibernation() are called when
'params.power_down' is not correct.  Get rid of
the pile of error checking.

- As part of this cleanup some of the error messages
not to have __func__ in them.  That's not needed
for dev_err() calls since they already have the
device name as part of the message.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210416124843.9EDCDA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Update dwc2_handle_usb_suspend_intr function.

To avoid working in two modes (partial power down
and hibernation) changed conditions for entering
partial power down or hibernation.

Instead of checking hw_params.power_optimized and
hw_params.hibernation now checking power_down
param which already set to one of the options
(Hibernation or Partial Power Down) based on
OTG_EN_PWROPT.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124835.9F257A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Add exit hibernation mode before removing drive

When dwc2 core is in hibernation mode loading
driver again causes driver fail. Because in
that mode registers are not accessible.

In order to exit from hibernation checking
dwc2 core power saving state in "dwc2_driver_remove()"
function. If core is in hibernation, then checking the
operational mode of the driver. To check whether dwc2 core
is operating in host mode or device mode there is one way
which is retrieving the backup value of "gotgctl" and compare
the "CurMod" value. If previously core entered hibernation
in host mode then the exit is performed for host if not then
exit is performed for device mode. The introduced checking
is because in hibernation state all registers are not
accessible.

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124827.9BB59A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Add hibernation exiting flow by system resume

Adds a new flow of exiting hibernation when PC is resumed
from suspend state.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124819.A3B26A005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Add hibernation entering flow by system suspend

Adds a new flow of entering hibernation when PC is
hibernated or suspended.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124811.BBFDBA005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Allow exit hibernation in urb enqueue

When core is in hibernation state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.

- Added exit from hibernation state to avoid port
reset issue and process upper layer request properly.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124803.D1C1FA005F@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Move exit hibernation to dwc2_port_resume() function

This move is done to call hibernation exit handler in
"dwc2_port_resume()" function when core receives port resume.
Otherwise it could be confusing to exit hibernation in
"dwc2_hcd_hub_control()" function but other power saving modes
in "dwc2_port_resume()" function.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124755.E47F3A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Move enter hibernation to dwc2_port_suspend() function

This move is done to call enter hibernation handler in
"dwc2_port_suspend()" function when core receives port suspend.
Otherwise it could be confusing to enter to hibernation in
"dwc2_hcd_hub_control()" function but other power saving modes
in "dwc2_port_suspend()" function.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124747.EE79EA005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Clear GINTSTS_RESTOREDONE bit after restore is generated.

When hibernation exit is performed the dwc2_hib_restore_common()
function is called. In that function we wait until GINTSTS_RESTOREDONE
bit is set. However, after the setting of that bit we get a lot of
(dwc2_hsotg_irq:) interrupts which indicates that (GINTSTS.RstrDoneInt)
restore done interrupt is asserted.

To avoid restore done interrupt storm after restore is generated
clear GINTSTS_RESTOREDONE bit in GINTSTS register.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124739.D6269A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Clear fifo_map when resetting core.

Switching from device mode to host mode by disconnecting
device cable core enters and exits form hibernation.
However, the fifo map remains not cleared. It results
to a WARNING (WARNING: CPU: 5 PID: 0 at drivers/usb/dwc2/
gadget.c:307 dwc2_hsotg_init_fifo+0x12/0x152 [dwc2])
if in host mode we disconnect the micro a to b host
cable. Because core reset occurs.

To avoid the WARNING, fifo_map should be cleared
in dwc2_core_reset() function by taking into account configs.
fifo_map must be cleared only if driver is configured in
"CONFIG_USB_DWC2_PERIPHERAL" or "CONFIG_USB_DWC2_DUAL_ROLE"
mode.

- Added "static inline void dwc2_clear_fifo_map()" helper
function to clear fifo_map with peripheral or dual role mode.

- Added a dummy version of "dwc2_clear_fifo_map()" helper
for host-only mode.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124731.C500AA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Allow exiting hibernation from gpwrdn rst detect

When device cable is disconnected core receives suspend
interrupt and enters hibernation. After entering
into hibernation GPWRDN_RST_DET and GPWRDN_STS_CHGINT
interrupts are asserted.

Allowed exit from gadget hibernation from
GPWRDN_RST_DET by checking only linestate.

Changed the return type of "dwc2_handle_gpwrdn_intr()"
function from void to int because exit from hibernation
functions have a return value.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124723.B6F17A005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Fix hibernation between host and device modes.

When core is in hibernation in host mode and a device cable
was connected then driver exited from device hibernation.
However, registers saved for host mode and when exited from
device hibernation register restore would be done for device
register which was wrong because there was no device registers
stored to restore.

- Added dwc_handle_gpwrdn_disc_det() function which handles
  gpwrdn disconnect detect flow and exits hibernation
  without restoring the registers.
- Updated exiting from hibernation in GPWRDN_STS_CHGINT with
  calling dwc_handle_gpwrdn_disc_det() function. Here no register
  is restored which is the solution described above.

Fixes: 65c9c4c6b01f ("usb: dwc2: Add dwc2_handle_gpwrdn_intr() handler")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124715.75355A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Fix host mode hibernation exit with remote wakeup flow.

Added setting "port_connect_status_change" flag to "1" in order
to re-enumerate, because after exit from hibernation port
connection status is not detected.

Fixes: c5c403dc4336 ("usb: dwc2: Add host/device hibernation functions")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124707.5EEC2A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Reset DEVADDR after exiting gadget hibernation.

Initially resetting device address was done in dwc2_hsotg_irq()
interrupt handler. However, when core is hibernated USB RESET
is not handled in dwc2_hsotg_irq() handler, instead USB RESET
interrupt is handled in dwc2_handle_gpwrdn_intr() handler.

- Added reset device address to zero when core exits from gadget
  hibernation.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124659.652CFA005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Update exit hibernation when port reset is asserted

No need to check for "DWC2_POWER_DOWN_PARAM_HIBERNATION" param
as "hsotg->hibernated" flag is already enough for exiting from
hibernation mode.

- Removes checking of "DWC2_POWER_DOWN_PARAM_HIBERNATION" param.

- For code readability Hibernation exit code moved after
debug message print.

- Added "dwc2_exit_hibernation()" function error checking.

Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124651.51C8DA005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-5.13-rc1' of https://git./linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial updates for 5.13-rc1

Here are the USB-serial updates for 5.13-rc1, including:

 - better type detection for pl2303
 - support for more line speeds for pl2303 (TA/TB)
 - fixed CSIZE handling for the new xr driver
 - core support for multi-interface functions
 - TIOCGSERIAL and TIOCSSERIAL fixes
 - generic TIOCSSERIAL support (e.g. for closing_wait)
 - fixed return value for unsupported ioctls
 - support for gpio valid masks in cp210x
 - drain-delay fixes and improvements
 - support for multi-port devices for xr
 - generalisation of the xr driver to support three new device classes
   (XR21B142X, XR21B1411 and XR2280X)

Included are also various clean ups.

All have been in linux-next with no reported issues.

* tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (72 commits)
  USB: cdc-acm: add more Maxlinear/Exar models to ignore list
  USB: serial: xr: add copyright notice
  USB: serial: xr: reset FIFOs on open
  USB: serial: xr: add support for XR22801, XR22802, XR22804
  USB: serial: xr: add support for XR21B1411
  USB: serial: xr: add support for XR21B1421, XR21B1422 and XR21B1424
  USB: serial: xr: add type abstraction
  USB: serial: xr: drop type prefix from shared defines
  USB: serial: xr: move pin configuration to probe
  USB: serial: xr: rename GPIO-pin defines
  USB: serial: xr: rename GPIO-mode defines
  USB: serial: xr: add support for XR21V1412 and XR21V1414
  USB: serial: ti_usb_3410_5052: clean up termios CSIZE handling
  USB: serial: ti_usb_3410_5052: use kernel types consistently
  USB: serial: ti_usb_3410_5052: add port-command helpers
  USB: serial: ti_usb_3410_5052: clean up vendor-request helpers
  USB: serial: ti_usb_3410_5052: drop unnecessary packed attributes
  USB: serial: io_ti: drop unnecessary packed attributes
  USB: serial: io_ti: use kernel types consistently
  USB: serial: io_ti: add read-port-command helper
  ...

usb: dwc3: gadget: Remove FS bInterval_m1 limitation

The programming guide incorrectly stated that the DCFG.bInterval_m1 must
be set to 0 when operating in fullspeed. There's no such limitation for
all IPs. See DWC_usb3x programming guide section 3.2.2.1.

Fixes: a1679af85b2a ("usb: dwc3: gadget: Fix setting of DEPCFG.bInterval_m1")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5d4139ae89d810eb0a2d8577fb096fc88e87bfab.1618472454.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci-mtk: remove bus status check

PM will take care of the status of child device, so no need
check each port anymore.

Suggested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618555706-6810-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: connector: Add slow-charger-loop definition

Allows PMIC charger loops which are slow(i.e. cannot meet the
15ms deadline) to still comply to pSnkStby i.e Maximum power
that can be consumed by sink while in Sink Standby state as defined
in 7.4.2 Sink Electrical Parameters of USB Power Delivery Specification
Revision 3.0, Version 1.2.

This patch introduces slow-charger-loop which when set makes
the port request PD_P_SNK_STDBY_MW(2.5W i.e 500mA@5V) upon entering
SNK_DISCOVERY (instead of 3A or the 1.5A during SNK_DISCOVERY) and the
actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during
SNK_READY for non-pd link.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414142656.63749-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Enable RPi in ACPI mode

The dwc2 driver has everything we need to run
in ACPI mode except for the ACPI module device table
boilerplate. With that added and identified as "BCM2848",
an id in use by other OSs for this device, the dw2
controller on the BCM2711 will work.

Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20210413215834.3126447-2-jeremy.linton@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: dwc3: Add disabling LPM for gadget

Add a new DT option to disable LPM for gadget and update the description
for usb2-lpm-disable related to host for clarity.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f31348ba744318c83b3a9ab1eab75c61122b15ae.1618366071.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: CDC-ACM: fix poison/unpoison imbalance

suspend() does its poisoning conditionally, resume() does it
unconditionally. On a device with combined interfaces this
will balance, on a device with two interfaces the counter will
go negative and resubmission will fail.

Both actions need to be done conditionally.

Fixes: 6069e3e927c8f ("USB: cdc-acm: untangle a circular dependency between callback and softint")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210421074513.4327-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Add reset-resume quirk for WD19's Realtek Hub

Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)

Information of this hub:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480  MxCh= 5
D:  Ver= 2.10 Cls=09(hub  ) Sub=00 Prot=02 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=5487 Rev= 1.47
S:  Manufacturer=Dell Inc.
S:  Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=01 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=02 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.

The quirky hub needs the reset-resume quirk to function correctly.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: net2272: remove redundant initialization of status

The variable status is being initialized with a value that is
never read and it is being updated later with a new value.  The
initialization is redundant and can be removed and move the
declaration of status to the scope where it is used.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210420110622.377339-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: storage: datafab: remove redundant assignment of variable result

The variable result is being assigned with a value that is
never read, the assignment is redundant and can be removed.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210420113818.378478-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: misc: adutux: fix whitespace coding style issue

Correct missing space error ceckpatch.pl is complaining about.

Signed-off-by: Malte Deiseroth <mdeiseroth88@gmail.com>
Link: https://lore.kernel.org/r/20210416080843.GA137657@utop
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: musb_core: Add space after that ','

Fix Error reported by checkpatch.pl

ERROR: space required after that ',' (ctx:VxV)
+#define can_bulk_split(musb,type) \
                            ^

ERROR: space required after that ',' (ctx:VxV)
+#define can_bulk_combine(musb,type) \
                              ^

Signed-off-by: Saurav Girepunje <saurav.girepunje@google.com>
Link: https://lore.kernel.org/r/20210418174720.GA59520@user
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: dummy_hcd: fix gpf in gadget_setup

Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.

The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:

        usb_gadget_disconnect(udc->gadget);
        if (udc->gadget->irq)
                synchronize_irq(udc->gadget->irq);
        udc->driver->unbind(udc->gadget);
        usb_gadget_udc_stop(udc);

usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.

But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.

To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.

Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: octeon: Use 'for_each_child_of_node'

Use 'for_each_child_of_node' instead of hand writing it.
This saves a few line of code.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/eaffe388e6c51e97caf3e8fa474de74428575455.1618920182.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Staging: rtl8723bs: rtw_xmit: fixed tabbing issue

Fixed warning from checkpatch for code block not being indented
correctly.

Signed-off-by: Amos Gross <email@amosgross.com>
Link: https://lore.kernel.org/r/YIAVfRxQ+XmKEf47@arch.localdomain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: remove unused function parameters

The Enable and Linked parameters of _BeaconFunctionEnable are not used.
Remove them.

Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20210419201126.25633-4-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: cmdThread is a task_struct

cmdThread is the return value of kthread_run, i.e. a struct task_struct.

Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20210419201126.25633-3-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: remove constant variable and dead code

g_wifi_on is always true. Remove the variable and the code that would
be run only if g_wifi_on was false.

While at it, remove a pointlesss comment that starts with /** and is
misinterpreted as a kernel-doc comment.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20210419201126.25633-2-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: change bLeisurePs' type to bool

bLeisurePs is used as a boolean variable. Change its type from
u8 to bool.

Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20210419201126.25633-1-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: remove empty #ifdef block

remove #ifdef block left empty after DBG_871X_LEVEL
deletion.

Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/c2600c9a71d4e222963cbc600b2e703fe2b1289f.1618480688.git.fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: remove unused DBG_871X_LEVEL macro declarations

remove unused DBG_871X_LEVEL macro declarations.

DBG_871X_LEVEL macro wraps a raw printk call which is not
recommended in a device driver context, prefer using
netdev_*() log functions.

Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/ec371fd8a4e53b4730b45f0a1c9210106b2914f2.1618480688.git.fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: split too long line

fix the following post-commit hook checkpatch issue.

WARNING: line length of 103 exceeds 100 columns
30: FILE: drivers/staging/rtl8723bs/core/rtw_mlme_ext.c:711:
+
receive_disconnect(padapter, pmlmeinfo->network.MacAddress, 0);

Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/4e87fb741205b9f314aec739921405a7ebef908a.1618480688.git.fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: fix indentation in if block

fix following post-commit hook checkpatch issues:

WARNING: suspect code indent for conditional statements (32, 48)
323: FILE: drivers/staging/rtl8723bs/core/rtw_mlme_ext.c:708:
  if (!ret) {
+
netdev_dbg(padapter->pnetdev,

Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/7f548510ebe2427e85f3fe8b33ed937160c64e9f.1618480688.git.fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: fix code indent issue

fix following post-commit hook checkpatch issues:

ERROR: code indent should use tabs where possible
887: FILE: drivers/staging/rtl8723bs/os_dep/os_intfs.c:1145:
+^I^I           "%s: ### ERROR #### driver in IPS
+ ####ERROR###!!!\n",$

ERROR: code indent should use tabs where possible
888: FILE: drivers/staging/rtl8723bs/os_dep/os_intfs.c:1146:
+^I^I           __func__);$

Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/2e0ba5214df41de7e46b8df4e62d2f38acea92ec.1618480688.git.fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: replace DBG_871X_LEVEL logs with netdev_*()

Replace DBG_871X_LEVEL logs with netdev_*() functions
where possible (i.e. where a pointer to netdev is easily
available).

This is not possible in correspondance of redundant
log in module initialization.

So remove those ones.

DBG_871X_LEVEL macro wraps a raw printk call which is not
recommended in a device driver context, prefer using
netdev_*() log functions.

The remove/replace operation has been done with the
following semantic patch script:

@@
expression list args;
identifier padapter;
identifier func;
symbol _drv_always_, _drv_info_, _drv_warning_;
symbol _drv_err_, _drv_emerg_;
@@

func(..., struct adapter *padapter, ...) {
<...
(
- DBG_871X_LEVEL(_drv_always_, args);
+ netdev_dbg(padapter->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_info_, args);
+ netdev_info(padapter->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_warning_, args);
+ netdev_warn(padapter->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_err_, args);
+ netdev_err(padapter->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_emerg_, args);
+ netdev_emerg(padapter->pnetdev, args);
)
...>
}

@rule@
identifier func, context, padapter;
@@

func(void *context)
{
...
struct adapter *padapter = context;
...
}

@@
expression list args;
identifier rule.padapter;
identifier rule.func, rule.context;
@@

func(void *context)
{
<...
(
- DBG_871X_LEVEL(_drv_always_, args);
+ netdev_dbg(padapter->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_info_, args);
+ netdev_info(padapter->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_warning_, args);
+ netdev_warn(padapter->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_err_, args);
+ netdev_err(padapter->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_emerg_, args);
+ netdev_emerg(padapter->pnetdev, args);
)
...>
}

@@
expression list args;
expression get_dev;
identifier func, dev;
@@

func(...)
{
...
struct net_device *dev = get_dev;
<...
(
- DBG_871X_LEVEL(_drv_always_, args);
+ netdev_dbg(dev, args);
|
- DBG_871X_LEVEL(_drv_info_, args);
+ netdev_info(dev, args);
|
- DBG_871X_LEVEL(_drv_warning_, args);
+ netdev_warn(dev, args);
|
- DBG_871X_LEVEL(_drv_err_, args);
+ netdev_err(dev, args);
|
- DBG_871X_LEVEL(_drv_emerg_, args);
+ netdev_emerg(dev, args);
)
...>
}

@@
expression list args;
identifier func, dev;
@@

func(struct net_device *dev)
{
<...
(
- DBG_871X_LEVEL(_drv_always_, args);
+ netdev_dbg(dev, args);
|
- DBG_871X_LEVEL(_drv_info_, args);
+ netdev_info(dev, args);
|
- DBG_871X_LEVEL(_drv_warning_, args);
+ netdev_warn(dev, args);
|
- DBG_871X_LEVEL(_drv_err_, args);
+ netdev_err(dev, args);
|
- DBG_871X_LEVEL(_drv_emerg_, args);
+ netdev_emerg(dev, args);
)
...>
}

@@
expression list args;
identifier func, dvobj;
@@

func(struct dvobj_priv *dvobj)
{
<...
(
- DBG_871X_LEVEL(_drv_always_, args);
+ netdev_dbg(dvobj->if1->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_info_, args);
+ netdev_info(dvobj->if1->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_warning_, args);
+ netdev_warn(dvobj->if1->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_err_, args);
+ netdev_err(dvobj->if1->pnetdev, args);
|
- DBG_871X_LEVEL(_drv_emerg_, args);
+ netdev_emerg(dvobj->if1->pnetdev, args);
)
...>
}

@@
@@

- DBG_871X_LEVEL(...);

Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/4a02f9f5665fa4b78c0b321ce0cc62254255c9dd.1618480688.git.fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192e: indent statement properly

Indent statement in an else branch.  Reported by checkpatch:
WARNING:SUSPECT_CODE_INDENT: suspect code indent for
conditional statements (8, 8)

Signed-off-by: Ian Kewish <iankewish@gmail.com>
Link: https://lore.kernel.org/r/20210415180645.65699-1-iankewish@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: allwinner: Revert SD card CD GPIO for Pine64-LTS

Commit 941432d00768 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.

This was based on the observation that the Pine64-LTS has as "push-push"
SD card socket, and that the schematic mentions the card detect GPIO.

After having received two reports about failing SD card access with that
patch, some more research and polls on that subject revealed that there
are at least two different versions of the Pine64-LTS out there:
- On some boards (including mine) the card detect pin is "stuck" at
  high, regardless of an microSD card being inserted or not.
- On other boards the card-detect is working, but is active-high, by
  virtue of an explicit inverter circuit, as shown in the schematic.

To cover all versions of the board out there, and don't take any chances,
let's revert the introduction of the active-low CD GPIO, but let's use
the broken-cd property for the Pine64-LTS this time. That should avoid
regressions and should work for everyone, even allowing SD card changes
now.
The SOPine card detect has proven to be working, so let's keep that
GPIO in place.

Fixes: 941432d00768 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card")
Reported-by: Michael Weiser <michael.weiser@gmx.de>
Reported-by: Daniel Kulesz <kuleszdl@posteo.org>
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Michael Weiser <michael.weiser@gmx.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210414104740.31497-1-andre.przywara@arm.com

fsverity: relax build time dependency on CRYPTO_SHA256

CONFIG_CRYPTO_SHA256 denotes the generic C implementation of the SHA-256
shash algorithm, which is selected as the default crypto shash provider
for fsverity. However, fsverity has no strict link time dependency, and
the same shash could be exposed by an optimized implementation, and arm64
has a number of those (scalar, NEON-based and one based on special crypto
instructions). In such cases, it makes little sense to require that the
generic C implementation is incorporated as well, given that it will never
be called.

To address this, relax the 'select' clause to 'imply' so that the generic
driver can be omitted from the build if desired.

Acked-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

fscrypt: relax Kconfig dependencies for crypto API algorithms

Even if FS encryption has strict functional dependencies on various
crypto algorithms and chaining modes. those dependencies could potentially
be satisified by other implementations than the generic ones, and no link
time dependency exists on the 'depends on' claused defined by
CONFIG_FS_ENCRYPTION_ALGS.

So let's relax these clauses to 'imply', so that the default behavior
is still to pull in those generic algorithms, but in a way that permits
them to be disabled again in Kconfig.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: camellia - drop duplicate "depends on CRYPTO"

All 5 CAMELLIA crypto driver Kconfig symbols have a duplicate
"depends on CRYPTO" line but they are inside an
"if CRYPTO"/"endif # if CRYPTO" block, so drop the duplicate "depends"
lines.

These 5 symbols still depend on CRYPTO.

Fixes: 584fffc8b196 ("[CRYPTO] kconfig: Ordering cleanup")
Fixes: 0b95ec56ae19 ("crypto: camellia - add assembler implementation for x86_64")
Fixes: d9b1d2e7e10d ("crypto: camellia - add AES-NI/AVX/x86_64 assembler implementation of camellia cipher")
Fixes: f3f935a76aa0 ("crypto: camellia - add AVX2/AES-NI/x86_64 assembler implementation of camellia cipher")
Fixes: c5aac2df6577 ("sparc64: Add DES driver making use of the new des opcodes.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sebastian Siewior <sebastian@breakpoint.cc>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: s5p-sss - consistently use local 'dev' variable in probe()

For code readability, the probe() function uses 'dev' variable instead
of '&pdev->dev', so update remaining places.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: s5p-sss - remove unneeded local variable initialization

The initialization of 'err' local variable is not needed as it is
shortly after overwritten.

Addresses-Coverity: Unused value
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: s5p-sss - simplify getting of_device_id match data

Use of_device_get_match_data() to make the code slightly smaller.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

ccp: ccp - add support for Green Sardine

Add a new PCI device entry for Green Sardine APU.

Signed-off-by: Devaraj Rangasamy <Devaraj.Rangasamy@amd.com>
Tested-by: Babulu Ellune <Babulu.Ellune@amd.com>
Signed-off-by: Rijo Thomas <Rijo-john.Thomas@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: ccp - Make ccp_dev_suspend and ccp_dev_resume void functions

Since ccp_dev_suspend() and ccp_dev_resume() only return 0 which causes
ret to equal 0 in sp_suspend and sp_resume, making the if condition
impossible to use. it might be a more appropriate fix to have these be
void functions and eliminate the if condition in sp_suspend() and
sp_resume().

Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: John Allen <john.allen@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: octeontx2 - add support for OcteonTX2 98xx CPT block.

OcteonTX2 series of silicons have multiple variants, the
98xx variant has two crypto (CPT0 & CPT1) blocks. This patch
adds support for firmware load on new CPT block(CPT1).

Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: chelsio/chcr - Remove useless MODULE_VERSION

kernel version describes module state more accurately.
hence remove chcr versioning.

Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: ux500/cryp - Remove duplicate argument

Fix the following coccicheck warning:

./drivers/crypto/ux500/cryp/cryp_p.h:84:6-27:duplicated argument to |

Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: chelsio - remove unused function

Fix the following clang warning:

drivers/crypto/chelsio/chcr_algo.c:129:19: warning: unused function
'is_ofld_imm' [-Wunused-function].

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: sa2ul - Add support for AM64

The sa2ul module in am64 have limited support for algorithms, and the
priv and priv_id used on the platform is different compared to AM654 or
j721e.

Use match data to get the SoC specific information and use it throughout
the driver.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vaibhav Gupta <v_gupta@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: sa2ul - Support for per channel coherency

On AM64 the DMA channel for sa2ul can be configured to be coherent or
non coherent via DT binding.

Use the dmaengine_get_device_for_dma_api() to get the device pointer which
should be used for with the dma_api to use matching dma_ops for the
channel coherency/non coherency.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vaibhav Gupta <v_gupta@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

dt-bindings: crypto: ti,sa2ul: Add new compatible for AM64

Add the AM64 version of sa2ul to the compatible list.

[v_gupta@ti.com: Conditional dma-coherent requirement, clocks]
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vaibhav Gupta <v_gupta@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: hisilicon - enable new error types for QM

QM adds 'qm_mailbox_timeout' and 'qm_flr_timeout' hardware error types on
Kunpeng930. This patch enables the new error types and configures the error
types as NFE.

Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: hisilicon - add new error type for SEC

Kunpeng930 SEC adds several new hardware error types. This patch enables
the new error types and configures the error types as NFE.

Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: hisilicon - support new error types for ZIP

Kunpeng930 ZIP adds 'zip_axi_poison_err' 'zip_sva_err' and
'QM_ACC_DO_TASK_TIMEOUT' hardware error types. This patch enables the error
types and configures the error types as NFE.

Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: hisilicon - dynamic configuration 'err_info'

'err_info' does not support dynamic configuration since it is const type.
Therefore, in order to support new error type later, 'err_info' is changed
to dynamic configuration.

Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: doc - fix kernel-doc notation in chacha.c and af_alg.c

Fix function name in chacha.c kernel-doc comment to remove a warning.

Convert af_alg.c to kernel-doc notation to eliminate many kernel-doc
warnings.

../lib/crypto/chacha.c:77: warning: expecting prototype for chacha_block(). Prototype was for chacha_block_generic() instead
chacha.c:104: warning: Excess function parameter 'out' description in 'hchacha_block_generic'

af_alg.c:498: warning: Function parameter or member 'sk' not described in 'af_alg_alloc_tsgl'
../crypto/af_alg.c:539: warning: expecting prototype for aead_count_tsgl(). Prototype was for af_alg_count_tsgl() instead
../crypto/af_alg.c:596: warning: expecting prototype for aead_pull_tsgl(). Prototype was for af_alg_pull_tsgl() instead
af_alg.c:663: warning: Function parameter or member 'areq' not described in 'af_alg_free_areq_sgls'
af_alg.c:700: warning: Function parameter or member 'sk' not described in 'af_alg_wait_for_wmem'
af_alg.c:700: warning: Function parameter or member 'flags' not described in 'af_alg_wait_for_wmem'
af_alg.c:731: warning: Function parameter or member 'sk' not described in 'af_alg_wmem_wakeup'
af_alg.c:757: warning: Function parameter or member 'sk' not described in 'af_alg_wait_for_data'
af_alg.c:757: warning: Function parameter or member 'flags' not described in 'af_alg_wait_for_data'
af_alg.c:757: warning: Function parameter or member 'min' not described in 'af_alg_wait_for_data'
af_alg.c:796: warning: Function parameter or member 'sk' not described in 'af_alg_data_wakeup'
af_alg.c:832: warning: Function parameter or member 'sock' not described in 'af_alg_sendmsg'
af_alg.c:832: warning: Function parameter or member 'msg' not described in 'af_alg_sendmsg'
af_alg.c:832: warning: Function parameter or member 'size' not described in 'af_alg_sendmsg'
af_alg.c:832: warning: Function parameter or member 'ivsize' not described in 'af_alg_sendmsg'
af_alg.c:985: warning: Function parameter or member 'sock' not described in 'af_alg_sendpage'
af_alg.c:985: warning: Function parameter or member 'page' not described in 'af_alg_sendpage'
af_alg.c:985: warning: Function parameter or member 'offset' not described in 'af_alg_sendpage'
af_alg.c:985: warning: Function parameter or member 'size' not described in 'af_alg_sendpage'
af_alg.c:985: warning: Function parameter or member 'flags' not described in 'af_alg_sendpage'
af_alg.c:1040: warning: Function parameter or member 'areq' not described in 'af_alg_free_resources'
af_alg.c:1059: warning: Function parameter or member '_req' not described in 'af_alg_async_cb'
af_alg.c:1059: warning: Function parameter or member 'err' not described in 'af_alg_async_cb'
af_alg.c:1083: warning: Function parameter or member 'file' not described in 'af_alg_poll'
af_alg.c:1083: warning: Function parameter or member 'sock' not described in 'af_alg_poll'
af_alg.c:1083: warning: Function parameter or member 'wait' not described in 'af_alg_poll'
af_alg.c:1114: warning: Function parameter or member 'sk' not described in 'af_alg_alloc_areq'
af_alg.c:1114: warning: Function parameter or member 'areqlen' not described in 'af_alg_alloc_areq'
af_alg.c:1146: warning: Function parameter or member 'sk' not described in 'af_alg_get_rsgl'
af_alg.c:1146: warning: Function parameter or member 'msg' not described in 'af_alg_get_rsgl'
af_alg.c:1146: warning: Function parameter or member 'flags' not described in 'af_alg_get_rsgl'
af_alg.c:1146: warning: Function parameter or member 'areq' not described in 'af_alg_get_rsgl'
af_alg.c:1146: warning: Function parameter or member 'maxsize' not described in 'af_alg_get_rsgl'
af_alg.c:1146: warning: Function parameter or member 'outlen' not described in 'af_alg_get_rsgl'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

usb: dwc3: gadget: Fix START_TRANSFER link state check

The START_TRANSFER command needs to be executed while in ON/U0 link
state (with an exception during register initialization). Don't use
dwc->link_state to check this since the driver only tracks the link
state when the link state change interrupt is enabled. Check the link
state from DSTS register instead.

Note that often the host already brings the device out of low power
before it sends/requests the next transfer. So, the user won't see any
issue when the device starts transfer then. This issue is more
noticeable in cases when the device delays starting transfer, which can
happen during delayed control status after the host put the device in
low power.

Fixes: 799e9dc82968 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/bcefaa9ecbc3e1936858c0baa14de6612960e909.1618884221.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: Fix double free of device descriptor pointers

Upon driver unbind usb_free_all_descriptors() function frees all
speed descriptor pointers without setting them to NULL. In case
gadget speed changes (i.e from super speed plus to super speed)
after driver unbind only upto super speed descriptor pointers get
populated. Super speed plus desc still holds the stale (already
freed) pointer. Fix this issue by setting all descriptor pointers
to NULL after freeing them in usb_free_all_descriptors().

Fixes: f5c61225cf29 ("usb: gadget: Update function for SuperSpeedPlus")
cc: stable@vger.kernel.org
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1619034452-17334-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>