iio: adc: ltc2497: split protocol independent part in a separate module

This allows to share most of this driver for the ltc2496 driver added in
the next commit that is an SPI variant of the ltc2497. Initially I named
the generic part ltc249x, but wild card names are frowned upon, so the
generic part is called ltc2497-core even though it's not obvious that
this is then to be reused for the ltc2496 driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ltc2496: provide device tree binding document

The ADC only requires the standard stuff for spi devices and a reference
voltage.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-ads1015: Make use of device property API

Make use of device property API in this driver so that both OF based
system and ACPI based system can use this driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-ads1015: Get rid of legacy platform data

Platform data is a legacy interface to supply device properties
to the driver. In this case we even don't have in-kernel users
for it. Just remove it for good.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-ads7950: Fix a typo in an error message

Fix a typo:
   s/get get/to get/

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: humidity: hts221: move register definitions to sensor structs

Move some register definitions to hts221_avg_list, hts221_avg_list and
hts221_channels since they are used only there and simplify driver code

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: stm32-adc: Add check on overrun interrupt

Enable overrun interrupt on STM32 ADC. In case data register hasn't been
read (by CPU or DMA), overrun condition is detected when there's new
conversion data available. Stop grabbing data and log an error message.
Use a threaded irq to avoid printing the error message from hard irq
context.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ssp_sensors: Convert to use GPIO descriptors

These three GPIO lines used by the Samsung sensor hub is pretty
straight-forward to convert to use GPIO descriptors.

Cc: Karol Wrona <k.wrona@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Move AD7091R5 entry in a alphabetical order in Makefile

Ad7091R5 was added in a non alphabetical order after AD7124 in Makefile and
KConfig. This patch fixes that and place Ad7091R5 before AD7124.

Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: atlas-ph-sensor: Drop GPIO include

The driver includes <linux/gpio.h> yet fails to use symbols
from any the header so drop the include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ad7266: Convert to use GPIO descriptors

The AD7266 have no in-tree users making use of the platform
data mechanism to pass address GPIO lines when not using
a fixed address, so we can easily convert this to use
GPIO descriptors instead of the platform data integers
currently passed.

Lowercase the labels "ad0".."ad2" as this will make a better
fit for platform descriptions like device tree that prefer
lowercase names such as "ad0-gpios" rather than "AD0-gpios".

Board files and other static users of this device can pass
the same GPIO descriptors using machine descriptor
tables if need be.

Cc: Alison Schofield <amsfield22@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ad5592r: Drop surplus GPIO header

This driver uses all the modern GPIO APIs from
<linux/gpio/driver.h> and <linux/gpio/consumer.h> so
just drop the unused legacy header <linux/gpio.h>.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adf4350: Convert to use GPIO descriptor

The lock detect GPIO line is better to grab using
a GPIO descriptor. We drop the pdata for this: clients using board
files can use machine descriptor tables to pass this GPIO from
static data.

Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: itg3200: Drop GPIO include

The driver include <linux/gpio.h> yet does not use any
of the symbols from the header, so drop the include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: apds9960: Drop GPIO includes

The driver includes <linux/gpio.h> and <linux/of_gpio.h> yet
fails to use symbols from any of the include files, so drop
these includes.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ad2s1200: Drop legacy include

This driver is using the GPIO descriptor API but yet includes
the legacy <linux/gpio.h> header for no reason. Drop the
surplus include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: si1145: Drop GPIO include

The driver include <linux/gpio.h> yet does not use any
of the symbols from the header, so drop the include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: as3935: Drop GPIO includes

The driver includes <linux/gpio.h> and <linux/of_gpio.h> yet
fails to use symbols from any of the include files, so drop
these includes.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: fix checkpatch warning

Fix following checkpatch warning:

CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+                                  const struct iio_chan_spec *chan,

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ak8975: Convert to use GPIO descriptor

The end-of-conversion (EOC) GPIO line is better to grab using
a GPIO descriptor. We drop the pdata for this: clients using board
files can use machine descriptor tables to pass this GPIO from
static data.

Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad799x: add pm_ops to disable the device completely

The device is always in a low-power state due to the hardware design. It
wakes up upon a conversion request and goes back into the low-power
state. The pm ops are added to disable the device completely and to free
the regulator. Disbaling the device completely should be not that
notable but freeing the regulator is important. Because if it is a shared
power-rail the regulator won't be disabled during suspend-to-ram/disk
and so all devices connected to that rail keeps on.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: inv_mpu6050: Select I2C_MUX again

commit f7072198f217 ("iio: imu: Fix inv_mpu6050 dependencies")
undid the explicit selection of I2C_MUX previously
done by the driver, because I2C_MUX implicitly depended
on HAS_IOMEM.

However commit 93d710a65ef0 ("i2c: mux: fix up dependencies")
cleared up the situation properly and drivers that need
to select I2C_MUX can now do so again.

It makes a lot of sense for a driver to select the driver
infrastructure it needs so restore the natural order of
things.

Cc: Richard Weinberger <richard@nod.at>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7887: Cleanup channel assignment

The channels specification assignment in chip info was simplified.
This patch makes supporting other devices by this driver easier.

Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ping: add parallax ping sensors

Add support for parallax ping and laser ping sensors with just one pin
for trigger and echo signal.

This driver is based on srf04. In contrast to it it's necessary to
change direction of the pin and to request the irq just for the period
when the echo is rising and falling. Because this adds a lot of cases
there is this individual driver for handling this type of sensors.

Add a new configuration variable CONFIG_PING to Kconfig and Makefile.

Julia reported an issue with failing to unlock a mutex in some error
paths.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: trigger: stm32-timer: remove unnecessary update event

There is no need to explicitly generate update event to update
timer master mode.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: Fix Kconfig indentation

Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^        /\t/' -i */Kconfig

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

MAINTAINERS: add maintainer for ping iio sensors

Add a maintainer for the new parallax PING))) and LaserPING IIO sensors

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: add parallax ping sensors

Add dt-bindings for parallax PING))) and LaserPING iio sensors, which
are used for measuring distances.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: add vendor prefix parallax

Add new vendor prefix parallax for newly created ping iio sensors.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad7303: use regulator get optional to check for ext supply

Previously, the code was using the of_read_property_bool() to check if
an external regulator was provided. However, this is redundant, as it's
more simple/direct to just ask the regulator is provided, via a
`devm_regulator_get_optional()` call.

Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: maxim_thermocouple: document new 'compatible' strings

Now the maxim_thermocouple has new, more specific, 'compatible' strings for
better distinguish the various supported chips.

This patch updates the DT bindings documentation accordingly

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: maxim_thermocouple: add thermocouple_type sysfs attribute

We added a sysfs ABI for getting/setting the type of a thermocouple. This
driver supports chips that support specific fixed thermocouple types; we
cannot set it, but still we can add this sysfs attribute in RO mode to
read-back the thermocouple type.

This driver supports actually several chips:
 - max6675
 - max31855[k/j/n/s/t/e/r]asa family

Max6675 supports only K-type thermocouples, so we can just report that.

Each chip in max31855 family supports just one specific thermocouple type
(in the obvious way: i.e. max31855jasa supports J-type). This driver did
accept a generic SPI ID and OF compatible "max31855" which does not give
any clue about which chip is really involved (and unfortunately it seems
we have no way to detect it).

This patch introduces a new set of, more specific, SPI IDs and OF
compatible strings to better match the chip type.

The old, generic, "max31855" binding is kept for compatibility reasons, but
this patch aims to deprecate it, so, should we hit it, a warning is spit.
In such case the reported thermocouple type in sysfs is '?', because we
have no way to know.

Regarding the implementation: the thermocouple type information is stored
in the driver private data and I've kept only two maxim_thermocouple_chip
types in order to avoid a lot of duplications (seven chip types with just
a different thermocouple type).

RFT because I have no real HW to test this.

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: max31856: add support for runtime-configuring the thermocouple type

The sensor support various thermocouple types (e.g. J, K, N, ...). The
driver allows to configure this parameter using a DT property.

This is useful when i.e. the thermocouple is physically tied to the sensor
and it is usually not removed, or when it is at least known in advance
which sensor will be connected to the circuit.

However, if the user can randomly connect any kind of thermocouples (i.e.
the device exposes a connector, and the user is free to connect its own
sensors), it would be more appropriate to provide a mechanism to
dynamically switch from one thermocouple type to another. This can be i.e.
handled in userspace by a GUI, a configuration file or a program that
detects the thermocouple type by reading a GPIO, or a eeprom on the probe,
or whatever.

This patch adds a IIO attribute that can be used to override, at run-time,
the DT-provided setting (which serves as default).

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Documentation: ABI: document IIO thermocouple_type file

IIO core layer gained a new sysfs standard attribute "thermocouple_type".
This patch adds it to the list of documented ABI for sysfs-bus-iio

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: core: add thermocouple_type standard attribute

We have a couple of thermocouple IIO drivers, supporting several chips.
Some of them support only one specific thermocouple type (e.g. "K", "J"),
one of them can be configured to work with several different thermocouple
types.

In certain applications thermocouples could be externally connected to the
chip by the user.

This patch introduces a new IIO standard attribute to report the supported
thermocouple type and, where applicable, to allow it to be dynamically set
using sysfs.

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: core: add char type for sysfs attributes

This patch introduces IIO_VAL_CHAR type for standard IIO attributes to
allow for attributes that needs to be represented by character rather
than a number. This is preparatory for introducing a new attribute whose
purpose is to describe thermocouple type, that can be i.e. "J", "K", etc..

The char-type value is stored in the first "value" integer that is passed
to the .[read/write]_raw() callbacks.

Note that in order to make it possible for the IIO core to correctly parse
this type (actually, to avoid integer parsing), it became mandatory for
any driver that wish to use IIO_VAL_CHAR on a writable attribute to
implement .write_raw_get_fmt().

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: max31856: add support for configuring the HW averaging

This sensor can perform samples averaging in hardware, but currently the
driver leaves this setting alone (default is no averaging).

This patch binds this HW setting to the "oversampling_ratio" IIO attribute
and allows the user to set the averaging as desired (the HW supports
averaging of 2, 5, 8 or 16 samples; in-between values are rounded up).

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Documentation: ABI: document IIO in_temp_filter_notch_center_frequency file

max31856 IIO driver introduced a new attribute
"in_temp_filter_notch_center_frequency".
This patch adds it to the list of documented ABI for sysfs-bus-iio

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: max31856: add option for setting mains filter rejection frequency

This sensor has an embedded notch filter for reducing interferences caused
by the power mains. This filter can be tuned to reject either 50Hz or 60Hz
(and harmonics).

Currently the said setting is left alone (the sensor defaults to 60Hz).
This patch introduces a IIO attribute that allows the user to set the said
filter to the desired frequency.

NOTE: this has been intentionally not tied to any DT property to allow
the configuration of this setting from userspace, e.g. with a GUI or by
reading a configuration file, or maybe reading a GPIO tied to a physical
switch or accessing some device that can autodetect the line frequency.

Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: gyro: adis16260: replace mlock with ADIS lib's state_lock

This change uses the ADIS library's state_lock to protect the state of the
`max_speed_hz` change that is done during the set of the sampling
frequency.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis16480: use state lock for filter freq set

It's the only operation that does 2 operations (a read & a write), so the
unlocked functions can be used under a single state lock.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: gyro: adis16136: rework locks using ADIS library's state lock

This replaces indio_dev's mlock with the state lock/mutex from the ADIS
library.

The __adis16136_get_freq() function has been prefixed to mark it as
unlocked. The adis16136_{set,get}_filter() functions now hold the state
lock for all the ops that they do.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis16400: rework locks using ADIS library's state lock

This change removes the use of indio_dev's mlock in favor using the state
lock from the ADIS library.

The set_freq() & get_freq() hooks are unlocked, so they require specific
locking. That is because in some cases the get_freq() hook is used in
combination with adis16400_set_filter().

In cases where only one read/write is done, the functions that hold the
state lock are used.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis: group single conversion under a single state lock

The single conversion function does a series of reads + writes. This change
extends the use of the state_lock for the entire set of operations.
Previously, indio_dev's mlock was used. This change also removes the use of
this lock.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis: protect initial startup routine with state lock

The initial startup routine is called by some ADIS drivers during probe,
and before registering with IIO. Normally, userspace should not be able to
do any access to the device (as there shouldn't be any available).

This change extends the state lock to the entire initial-startup routine.
Behaviourally nothing should change, but this should make the library
function a bit more robust.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis: create an unlocked version of adis_reset()

The reset routine may also be important to be protected by the state-lock
and grouped with other operations, so create an unlocked version, so that
this can be done.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis: create an unlocked version of adis_check_status()

This one also gets re-used in certain operations, so it makes sense to
have an unlocked version of this to group it with other
reads/writes/operations to have a single lock for the whole state change.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis[16480]: group RW into a single lock in adis_enable_irq()

The adis_enable_irq() does a read & a write. This change keeps a lock for
the duration of both operations vs for each op.

The change is also needed in adis16480, since that has it's own
implementation for adis_enable_irq().

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis: add unlocked read/write function versions

This will allow more flexible control to group reads & writes into a single
lock (particularly the state_lock).

The end-goal is to remove the indio_dev->mlock usage, and the simplest fix
would have been to just add another lock, which would not be a good idea on
the long-run.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis: rename txrx_lock -> state_lock

The lock can be extended a bit to protect other elements that are not
particular to just TX/RX. Another idea would have been to just add a new
`state_lock`, but that would mean 2 locks which would be redundant, and
probably cause more potential for dead-locks.

What will be done in the next patches, will be to add some unlocked
versions for read/write_reg functions.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max9611: Make enum relations more future proof

The relations between enum values and array indices values are currently
not enforced by the code, which makes them fragile w.r.t. future
changes.

Fix this by:
  1. Using designated array initializers, to make sure array indices and
     enums values match,
  2. Linking max9611_csa_gain enum values to the corresponding
     max9611_conf_ids enum values, as the latter is cast to the former
     in max9611_read_csa_voltage().

No change in generated code.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: inv_mpu6050: add support of MPU9150 magnetometer

Add support for driving MPU9150 magnetometer (AK8975) from mpu.

Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: inv_mpu6050: delete not existing MPU9150 spi support

MPU9150 is i2c only.
Update Kconfig to delete in description chips that are i2c or
spi only.

Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

MAINTAINERS: add entry for AD7091R5 driver

Add Beniamin Bia as a maintainer for AD7091R5 ADC.

Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-binding: iio: Add documentation for AD7091R5

Documentation for AD7091R5 ADC was added.

Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7091r5: Add scale and external VREF support

The scale can now be obtained with the "in_voltage_scale" file.
By default, the scale returned corresponds to the internal VREF of 2.5V.

It is possible to use an external VREF (through the REFIN/REFOUT pin of
the chip), by passing a regulator to the driver. The scale will then be
calculated according to the voltage reported by the regulator.

Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Add support for AD7091R5 ADC

AD7091R5 is 4-Channel, I2C, Ultra Low Power,12-Bit ADC.

This driver will also support AD7091R2/4/8 in the future.

Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7091r-5.pdf
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: buffer-dmaengine: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: vchiq: Refactor indentation in vchiq_platform_conn_state_changed()

Reducing the indentation level helps a bit with
the readability of this function. There's also a checkpatch
fix here, moving the first argument to kthread_create() onto
the same line, as well as a relocation of the statement
"char threadname[16];" to the top of the function to avoid
a declaration in the middle of code.

Signed-off-by: Marcelo Diop-Gonzalez <marcgonzalez@google.com>
Link: https://lore.kernel.org/r/20191114232801.71458-1-marcgonzalez@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: fix spelling mistake "maont" -> "mount"

There is a spelling mistake in a kernel info message. Fix it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191114221509.10728-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: remove two unused functions

Fix sparse warnings:

drivers/staging/exfat/exfat_core.c:2045:4: warning: symbol 'calc_checksum_1byte' was not declared. Should it be static?
drivers/staging/exfat/exfat_core.c:2080:5: warning: symbol 'calc_checksum_4byte' was not declared. Should it be static?

The two functions has no caller in tree, so remove it.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191114140348.46088-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: fix indentation issue

There is a block of statements that are indented
too deeply, remove the extraneous tabs.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191114095747.132407-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: fix indentation issue

There is a block of statements that are indented
too deeply, remove the extraneous tabs.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191114095430.132120-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ralink: enable PCI support only if driver for mt7621 SoC is selected

Some versions of SoC MT7621 have three PCI express hosts. Some boards
make use of those PCI through the staging driver mt7621-pci. Recently
PCI support has been removed from MT7621 Soc kernel configuration due
to a build error. This makes imposible to compile staging driver and
produces a regression for gnubee based boards. Enable support for PCI
again but enable it only if staging mt7621-pci driver is selected.

Fixes: c4d48cf5e2f0 ("MIPS: ralink: deactivate PCI support for SOC_MT7621")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: john@phrozen.org
Cc: NeilBrown <neil@brown.name>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20191019081233.7337-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: align to fix warnings of line over 80 characters

Align to fix multiple warnings of line over 80 characters.
Issue detected by checkpatch tool.

Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20191113110052.14855-1-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: fix indentation issue

There is a declaration that requires indentation. Add in
the missing tab.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191113164210.103586-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-5.5c' of https://git./linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Third set of IIO new device support cleanups and fixes for the 5.5 cycle.

New device support
* ad5446
  - Support the ad5600 DAC (id only needed).
* ad7292 ADC DAC etc
  - New driver plus dt-bindings.
* veml6030 ambient light sensor
  - New driver plus dt-bindings and sysfs docs.

Features
* mpu6050
  - Explicit VDD control.
* stm32-adc
  - Allow limiting of max clock frequency from devicetree to ensure it's
    suitable for external circuitry.

yaml binding conversions
* ltc1660
* mcp3911

Fixes
* adis16480
  - Fix wrong scale factors.
  - Fix debugfs reg access by providing the callback.
* cros_ec_baro
  - Fixing missing mask entry to make available sample frequencies visible
    in sysfs.
* st_lsm6dsx
  - Explicitly handle different ODR table sizes.
  - Handle restrictions between slave ODR and accel ODR when
    both are enabled.
  - Allow ODR to be expressed more accurately by using miliHz.
* tools
  - Fix an issue with parallel builds.

Cleanups and warning fixes
* adis16136, adis16400, adis16460, adis-lib
  - Change some checks on return values to be for 0 rather than strictly
    negative. Avoids some fiddly issues with the compiler concluding some
    variables are initialized due to a mixture of error checks.
  - Assign values only on success of 'read' operations - avoiding any
    chance the compiler will falsly suggest they might be used uninitialized.
  - Whitespace and simlar cleanups.
* aspeed adc
  - devm_platfom_ioremap_resource to reduce boilerplate.
* bcm-iproc-adc
  - Stray semicolon removal.
* cc10001
  - devm_platfom_ioremap_resource to reduce boilerplate.
* dln2-adc
  - Reorganise the buffered mode setup and tear down. Part of moving towards
    being able to refactor this area of the IIO core.
* hdc100x
  - Reorganise the buffered mode setup and tear down.
* ingenic-adc
  - devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-adc
  - devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-dac
  - devm_platfom_ioremap_resource to reduce boilerplate.
* mt6577
  - devm_platfom_ioremap_resource to reduce boilerplate.
* npcm
  - devm_platfom_ioremap_resource to reduce boilerplate.
* rcar-gyroadc
  - devm_platfom_ioremap_resource to reduce boilerplate.
* spear-adc
  - devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-adc
  - devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-dac
  - devm_platfom_ioremap_resource to reduce boilerplate.

* tag 'iio-for-5.5c' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (43 commits)
  iio: adis16480: Add debugfs_reg_access entry
  iio: adis16480: Fix scales factors
  tools: iio: Correctly add make dependency for iio_utils
  iio: adc: Add driver support for AD7292
  dt-bindings: iio: adc: Add dt-schema for AD7292
  dt-bindings: iio: adc: Migrate MCP3911 documentation to yaml
  iio: imu: mpu6050: Add support for vdd-supply regulator
  dt-bindings: iio: imu: mpu6050: add vdd-supply
  iio: cros_ec_baro: set info_mask_shared_by_all_available field
  iio: dac: ad5446: Add support for new AD5600 DAC
  dt-bindings: iio: dac: Migrate LTC1660 documentation to yaml
  iio: documentation: light: Add veml6030 sysfs documentation
  dt-bindings: iio: light: add veml6030 ALS bindings
  iio: light: add driver for veml6030 ambient light sensor
  iio: imu: st_lsm6dsx: express odr in mHZ
  iio: imu: st_lsm6dsx: fix ODR check in st_lsm6dsx_write_raw
  iio: imu: st_lsm6dsx: explicitly define odr table size
  iio: adc: stm32: allow to tune analog clock
  dt-bindings: iio: stm32-adc: add max clock rate property
  iio: dac: vf610: Use devm_platform_ioremap_resource
  ...

staging: exfat: Update the TODO file

Updating with the current laundry list of things that need attention.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112223609.163501-1-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up the namespace pollution part 8

Rename all the FAT_* functions to exfat_fat_*.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-13-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up the namespace pollution part 7

Global functions called 'buf*' are a linkage editor disaster waiting to
happen.  Rename our buf_* functions to exfat_buf_*

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-12-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up the namespace pollution part 6

Move a few more things so we can make them static and clear exfat.h out.
At this point, pretty much everything that can be static is static.
(Note: FAT_sync(), buf_sync(), and sync_alloc_bitmap() aren't called
anyplace, but aren't static because (a) that will toss an error and
(b) they probably *should* be getting called someplace

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-11-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up the namespace pollution part 5

Some more functions that can be moved and made static

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-10-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up the namespace pollution part 4

Relocating these functions to before first use lets us make them static

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-9-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up the namespace pollution part 3

These functions are only used in the local file, make them static

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-8-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up the namespace pollution part 2

Rename all the bdev_* to exfat_bdev_*

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-7-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up the namespace pollution part 1

Everything referenced in the struct fs_func exfat_fs_func is located
in that same .c file.  Make them static and remove from exfat.h

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-6-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Remove FAT/VFAT mount support, part 4

The code simplification from the previous patch rendered a few more
routines unreferenced, so heave them over the side as well.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-5-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Remove FAT/VFAT mount support, part 3

In this patch, we straighten out most of the cases where the
code was testing 'p_fs->vol_type == EXFAT' and '!= EXFAT'

There's still some ?: ops and a few places where the code
is doing checks for '.' and '..' that require looking at,
but those are future patches

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-4-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Remove FAT/VFAT mount support, part 2

Remove no longer referenced FAT/VFAT routines.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-3-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Remove FAT/VFAT mount support, part 1

Remove the top-level mount functionality, to make this driver handle
only exfat file systems.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112211238.156490-2-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Correct return code

Use -ENOTEMPTY rather than -EEXIST for attempting to remove
a directory that still has files in it.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112021000.42091-10-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Collapse redundant return code translations

Now that we no longer use odd internal return codes, we can
heave the translation code over the side, and just pass the
error code back up the call chain.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112021000.42091-9-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up return codes - FFS_SUCCESS

Convert FFS_SUCCESS to 0.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112021000.42091-8-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up return codes - remove unused codes

There are 6 FFS_* error values not used at all. Remove them.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112021000.42091-7-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up return codes - FFS_ERROR

Convert FFS_ERROR to -EINVAL

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112021000.42091-6-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up return codes - FFS_INVALIDFID

Covert FFS_INVALIDFID to -EINVAL

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112021000.42091-5-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up return codes - FFS_EOF

Convert FFS_EOF to return 0 for a zero-length read() as per 'man 2 read'.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112021000.42091-4-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up return codes - FFS_MEDIAERR

Convert FFS_MEDIAERR to (mostly) -ENOENT and -EIO.  Some additional code surgery
needed to propogate correct error codes upwards.

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112021000.42091-3-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: exfat: Clean up return codes - FFS_FORMATERR

Convert FFS_FORMATERR to -EFSCORRUPTED

Signed-off-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Link: https://lore.kernel.org/r/20191112021000.42091-2-Valdis.Kletnieks@vt.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dpaa2-ethsw: ordered workqueue should be per ethsw

Create a different ordered workqueue per dpaa2-ethsw instance.  Without
this change, we overwrite the global queue and leak memory when probing
multiple instances of the driver.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1573491058-24766-5-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dpaa2-ethsw: move port switchdev blocking notifier per ethsw

Register a different switchdev blocking notifier block per ethsw
instance.  When probing multiple dpaa2-ethsw instances, without this the
register will fail.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1573491058-24766-4-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dpaa2-ethsw: move port switchdev notifier per ethsw

Register a different switchdev notifier block per ethsw instance.
When probing multiple dpaa2-ethsw instances, without this the register
will fail.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1573491058-24766-3-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dpaa2-ethsw: move port notifier per ethsw

Register a different net_device notifier block per ethsw instance.
When probing multiple dpaa2-ethsw instances, without this the register
will fail.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1573491058-24766-2-git-send-email-ioana.ciornei@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Remove unnecessary braces

This patch removes unnecessary braces on single statement blocks or
that aren't necessary in any arm of the statement.
Issue found by Checkpatch.

Signed-off-by: Javier F. Arias <jarias.linux@gmail.com>
Link: https://lore.kernel.org/r/041503946a1c58111e69579838b184359745d8c1.1573577309.git.jarias.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Remove blank lines after an open brace

This patch removes blank lines after an open brace.
Issue found by checkpatch.

Signed-off-by: Javier F. Arias <jarias.linux@gmail.com>
Link: https://lore.kernel.org/r/847ce59f8429afaac1299794987779d0db54d0be.1573577309.git.jarias.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Remove blank lines before a close brace

This patch removes blank lines before a close brase.
Issue found by checkpatch.

Signed-off-by: Javier F. Arias <jarias.linux@gmail.com>
Link: https://lore.kernel.org/r/369fa1068078d98d658fe5e8fc335df1b22f5238.1573577309.git.jarias.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Remove multiple blank lines

This patch removes multiple blank lines to solve the warning found by
checkpatch.

Signed-off-by: Javier F. Arias <jarias.linux@gmail.com>
Link: https://lore.kernel.org/r/257b08ad13aa23c2ee53fc333ea3c3f7e3105791.1573577309.git.jarias.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: most: core: add comments to mutex and spinlock definitions

This patch adds a comment to the start_mutex and fifo_lock fields of
the most_channel structure definition.

Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Link: https://lore.kernel.org/r/1573566036-2279-1-git-send-email-christian.gromm@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adis16480: Add debugfs_reg_access entry

The driver is defining debugfs entries by calling
`adis16480_debugfs_init()`. However, those entries are attached to the
iio_dev debugfs entry which won't exist if no debugfs_reg_access
callback is provided.

Fixes: 2f3abe6cbb6c ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adis16480: Fix scales factors

This patch fixes the scales for the gyroscope, accelerometer and
barometer. The pressure scale was just wrong. For the others, the scale
factors were not taking into account that a 32bit word is being read
from the device.

Fixes: 7abad1063deb ("iio: adis16480: Fix scale factors")
Fixes: 82e7a1b25017 ("iio: imu: adis16480: Add support for ADIS1649x family of devices")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>