Xin Long [Thu, 29 Oct 2020 07:05:06 +0000 (15:05 +0800)]
sctp: support for sending packet over udp4 sock
This patch does what the rfc6951#section-5.3 says for ipv4:
"Within the UDP header, the source port MUST be the local UDP
encapsulation port number of the SCTP stack, and the destination port
MUST be the remote UDP encapsulation port number maintained for the
association and the destination address to which the packet is sent
(see Section 5.1).
Because the SCTP packet is the UDP payload, the length of the UDP
packet MUST be the length of the SCTP packet plus the size of the UDP
header.
The SCTP checksum MUST be computed for IPv4 and IPv6, and the UDP
checksum SHOULD be computed for IPv4 and IPv6."
Some places need to be adjusted in sctp_packet_transmit():
1. For non-gso packets, when transport's encap_port is set, sctp
checksum has to be done in sctp_packet_pack(), as the outer
udp will use ip_summed = CHECKSUM_PARTIAL to do the offload
setting for checksum.
2. Delay calling dst_clone() and skb_dst_set() for non-udp packets
until sctp_v4_xmit(), as for udp packets, skb_dst_set() is not
needed before calling udp_tunnel_xmit_skb().
then in sctp_v4_xmit():
1. Go to udp_tunnel_xmit_skb() only when transport->encap_port and
net->sctp.udp_port both are set, as these are one for dst port
and another for src port.
2. For gso packet, SKB_GSO_UDP_TUNNEL_CSUM is set for gso_type, and
with this udp checksum can be done in __skb_udp_tunnel_segment()
for each segments after the sctp gso.
3. inner_mac_header and inner_transport_header are set, as these
will be needed in __skb_udp_tunnel_segment() to find the right
headers.
4. df and ttl are calculated, as these are the required params by
udp_tunnel_xmit_skb().
5. nocheck param has to be false, as "the UDP checksum SHOULD be
computed for IPv4 and IPv6", says in rfc6951#section-5.3.
v1->v2:
- Use sp->udp_port instead in sctp_v4_xmit(), which is more safe.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:05:05 +0000 (15:05 +0800)]
sctp: call sk_setup_caps in sctp_packet_transmit instead
sk_setup_caps() was originally called in Commit
90017accff61 ("sctp:
Add GSO support"), as:
"We have to refresh this in case we are xmiting to more than one
transport at a time"
This actually happens in the loop of sctp_outq_flush_transports(),
and it shouldn't be tied to gso, so move it out of gso part and
before sctp_packet_pack().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:05:04 +0000 (15:05 +0800)]
sctp: add udphdr to overhead when udp_port is set
sctp_mtu_payload() is for calculating the frag size before making
chunks from a msg. So we should only add udphdr size to overhead
when udp socks are listening, as only then sctp can handle the
incoming sctp over udp packets and outgoing sctp over udp packets
will be possible.
Note that we can't do this according to transport->encap_port, as
different transports may be set to different values, while the
chunks were made before choosing the transport, we could not be
able to meet all rfc6951#section-5.6 recommends.
v1->v2:
- Add udp_port for sctp_sock to avoid a potential race issue, it
will be used in xmit path in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:05:03 +0000 (15:05 +0800)]
sctp: allow changing transport encap_port by peer packets
As rfc6951#section-5.4 says:
"After finding the SCTP association (which
includes checking the verification tag), the UDP source port MUST be
stored as the encapsulation port for the destination address the SCTP
packet is received from (see Section 5.1).
When a non-encapsulated SCTP packet is received by the SCTP stack,
the encapsulation of outgoing packets belonging to the same
association and the corresponding destination address MUST be
disabled."
transport encap_port should be updated by a validated incoming packet's
udp src port.
We save the udp src port in sctp_input_cb->encap_port, and then update
the transport in two places:
1. right after vtag is verified, which is required by RFC, and this
allows the existent transports to be updated by the chunks that
can only be processed on an asoc.
2. right before processing the 'init' where the transports are added,
and this allows building a sctp over udp connection by client with
the server not knowing the remote encap port.
3. when processing ootb_pkt and creating the temporary transport for
the reply pkt.
Note that sctp_input_cb->header is removed, as it's not used any more
in sctp.
v1->v2:
- Change encap_port as __be16 for sctp_input_cb.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:05:02 +0000 (15:05 +0800)]
sctp: add SCTP_REMOTE_UDP_ENCAPS_PORT sockopt
This patch is to implement:
rfc6951#section-6.1: Get or Set the Remote UDP Encapsulation Port Number
with the param of the struct:
struct sctp_udpencaps {
sctp_assoc_t sue_assoc_id;
struct sockaddr_storage sue_address;
uint16_t sue_port;
};
the encap_port of sock, assoc or transport can be changed by users,
which also means it allows the different transports of the same asoc
to have different encap_port value.
v1->v2:
- no change.
v2->v3:
- fix the endian warning when setting values between encap_port and
sue_port.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:05:01 +0000 (15:05 +0800)]
sctp: add encap_port for netns sock asoc and transport
encap_port is added as per netns/sock/assoc/transport, and the
latter one's encap_port inherits the former one's by default.
The transport's encap_port value would mostly decide if one
packet should go out with udp encapsulated or not.
This patch also allows users to set netns' encap_port by sysctl.
v1->v2:
- Change to define encap_port as __be16 for sctp_sock, asoc and
transport.
v2->v3:
- No change.
v3->v4:
- Add 'encap_port' entry in ip-sysctl.rst.
v4->v5:
- Improve the description of encap_port in ip-sysctl.rst.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:05:00 +0000 (15:05 +0800)]
sctp: add encap_err_lookup for udp encap socks
As it says in rfc6951#section-5.5:
"When receiving ICMP or ICMPv6 response packets, there might not be
enough bytes in the payload to identify the SCTP association that the
SCTP packet triggering the ICMP or ICMPv6 packet belongs to. If a
received ICMP or ICMPv6 packet cannot be related to a specific SCTP
association or the verification tag cannot be verified, it MUST be
discarded silently. In particular, this means that the SCTP stack
MUST NOT rely on receiving ICMP or ICMPv6 messages. Implementation
constraints could prevent processing received ICMP or ICMPv6
messages."
ICMP or ICMPv6 packets need to be handled, and this is implemented by
udp encap sock .encap_err_lookup function.
The .encap_err_lookup function is called in __udp(6)_lib_err_encap()
to confirm this path does need to be updated. For sctp, what we can
do here is check if the corresponding asoc and transport exist.
Note that icmp packet process for sctp over udp is done by udp sock
.encap_err_lookup(), and it means for now we can't do as much as
sctp_v4/6_err() does. Also we can't do the two mappings mentioned
in rfc6951#section-5.5.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:04:59 +0000 (15:04 +0800)]
sctp: create udp6 sock and set its encap_rcv
This patch is to add the udp6 sock part in sctp_udp_sock_start/stop().
udp_conf.use_udp6_rx_checksums is set to true, as:
"The SCTP checksum MUST be computed for IPv4 and IPv6, and the UDP
checksum SHOULD be computed for IPv4 and IPv6"
says in rfc6951#section-5.3.
v1->v2:
- Add pr_err() when fails to create udp v6 sock.
- Add #if IS_ENABLED(CONFIG_IPV6) not to create v6 sock when ipv6 is
disabled.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:04:58 +0000 (15:04 +0800)]
sctp: create udp4 sock and add its encap_rcv
This patch is to add the functions to create/release udp4 sock,
and set the sock's encap_rcv to process the incoming udp encap
sctp packets. In sctp_udp_rcv(), as we can see, all we need to
do is fix the transport header for sctp_rcv(), then it would
implement the part of rfc6951#section-5.4:
"When an encapsulated packet is received, the UDP header is removed.
Then, the generic lookup is performed, as done by an SCTP stack
whenever a packet is received, to find the association for the
received SCTP packet"
Note that these functions will be called in the last patch of
this patchset when enabling this feature.
v1->v2:
- Add pr_err() when fails to create udp v4 sock.
v2->v3:
- Add 'select NET_UDP_TUNNEL' in sctp Kconfig.
v3->v4:
- No change.
v4->v5:
- Change to set udp_port to 0 by default.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:04:57 +0000 (15:04 +0800)]
udp: support sctp over udp in skb_udp_tunnel_segment
For the gso of sctp over udp packets, sctp_gso_segment() will be called in
skb_udp_tunnel_segment(), we need to set transport_header to sctp header.
As all the current HWs can't handle both crc checksum and udp checksum at
the same time, the crc checksum has to be done in sctp_gso_segment() by
removing the NETIF_F_SCTP_CRC flag from the features.
Meanwhile, if the HW can't do udp checksum, csum and csum_start has to be
set correctly, and udp checksum will be done in __skb_udp_tunnel_segment()
by calling gso_make_checksum().
Thanks to Paolo, Marcelo and Guillaume for helping with this one.
v1->v2:
- no change.
v2->v3:
- remove the he NETIF_F_SCTP_CRC flag from the features.
- set csum and csum_start in sctp_gso_make_checksum().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:04:56 +0000 (15:04 +0800)]
udp6: move the mss check after udp gso tunnel processing
For some protocol's gso, like SCTP, it's using GSO_BY_FRAGS for
gso_size. When using UDP to encapsulate its packet, it will
return error in udp6_ufo_fragment() as skb->len < gso_size,
and it will never go to the gso tunnel processing.
So we should move this check after udp gso tunnel processing,
the same as udp4_ufo_fragment() does.
v1->v2:
- no change.
v2->v3:
- not do any cleanup.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 29 Oct 2020 07:04:55 +0000 (15:04 +0800)]
udp: check udp sock encap_type in __udp_lib_err
There is a chance that __udp4/6_lib_lookup() returns a udp encap
sock in __udp_lib_err(), like the udp encap listening sock may
use the same port as remote encap port, in which case it should
go to __udp4/6_lib_err_encap() for more validation before
processing the icmp packet.
This patch is to check encap_type in __udp_lib_err() for the
further validation for a encap sock.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King [Thu, 29 Oct 2020 16:09:03 +0000 (16:09 +0000)]
net: dsa: mv88e6xxx: fix vlan setup
DSA assumes that a bridge which has vlan filtering disabled is not
vlan aware, and ignores all vlan configuration. However, the kernel
software bridge code allows configuration in this state.
This causes the kernel's idea of the bridge vlan state and the
hardware state to disagree, so "bridge vlan show" indicates a correct
configuration but the hardware lacks all configuration. Even worse,
enabling vlan filtering on a DSA bridge immediately blocks all traffic
which, given the output of "bridge vlan show", is very confusing.
Allow the VLAN configuration to be updated on Marvell DSA bridges,
otherwise we end up cutting all traffic when enabling vlan filtering.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1kYAU3-00071C-1G@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bhaskar Chowdhury [Thu, 29 Oct 2020 09:55:25 +0000 (15:25 +0530)]
drivers: net: phy: Fix spelling in comment defalut to default
Fixed spelling in comment like below:
s/defalut/default/p
This is in linux-next.
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201029095525.20200-1-unixbhaskar@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lukas Bulwahn [Wed, 28 Oct 2020 11:35:33 +0000 (12:35 +0100)]
net: cls_api: remove unneeded local variable in tc_dump_chain()
make clang-analyzer on x86_64 defconfig caught my attention with:
net/sched/cls_api.c:2964:3: warning: Value stored to 'parent' is never read
[clang-analyzer-deadcode.DeadStores]
parent = 0;
^
net/sched/cls_api.c:2977:4: warning: Value stored to 'parent' is never read
[clang-analyzer-deadcode.DeadStores]
parent = q->handle;
^
Commit
32a4f5ecd738 ("net: sched: introduce chain object to uapi")
introduced tc_dump_chain() and this initial implementation already
contained these unneeded dead stores.
Simplify the code to make clang-analyzer happy.
As compilers will detect these unneeded assignments and optimize this
anyway, the resulting binary is identical before and after this change.
No functional change. No change in object code.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20201028113533.26160-1-lukas.bulwahn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lukas Bulwahn [Wed, 28 Oct 2020 11:53:49 +0000 (12:53 +0100)]
ipv6: mcast: make annotations for ip6_mc_msfget() consistent
Commit
931ca7ab7fe8 ("ip*_mc_gsfget(): lift copyout of struct group_filter
into callers") adjusted the type annotations for ip6_mc_msfget() at its
declaration, but missed the type annotations at its definition.
Hence, sparse complains on ./net/ipv6/mcast.c:
mcast.c:550:5: error: symbol 'ip6_mc_msfget' redeclared with different type \
(incompatible argument 3 (different address spaces))
Make ip6_mc_msfget() annotations consistent, which also resolves this
warning from sparse:
mcast.c:607:34: warning: incorrect type in argument 1 (different address spaces)
mcast.c:607:34: expected void [noderef] __user *to
mcast.c:607:34: got struct __kernel_sockaddr_storage *p
No functional change. No change in object code.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20201028115349.6855-1-lukas.bulwahn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hoang Huu Le [Wed, 28 Oct 2020 03:27:12 +0000 (10:27 +0700)]
tipc: remove dead code in tipc_net and relatives
dist_queue is no longer used since commit
37922ea4a310
("tipc: permit overlapping service ranges in name table")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au>
Link: https://lore.kernel.org/r/20201028032712.31009-1-hoang.h.le@dektech.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 01:33:44 +0000 (02:33 +0100)]
net: ipv6: calipso: Fix kerneldoc warnings
net/ipv6/calipso.c:1236: warning: Excess function parameter 'reg' description in 'calipso_req_delattr'
net/ipv6/calipso.c:1236: warning: Function parameter or member 'req' not described in 'calipso_req_delattr'
net/ipv6/calipso.c:435: warning: Excess function parameter 'audit_secid' description in 'calipso_doi_remove'
net/ipv6/calipso.c:435: warning: Function parameter or member 'audit_info' not described in 'calipso_doi_remove'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028013344.931928-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 01:31:23 +0000 (02:31 +0100)]
net: ipv6: rpl*: Fix strange kerneldoc warnings due to bad header
net/ipv6/rpl_iptunnel.c:15: warning: cannot understand function prototype: 'struct rpl_iptunnel_encap '
The header on the file containing the author copyright message uses
kerneldoc /** opener. This confuses the parser when it gets to
struct rpl_iptunnel_encap {
struct ipv6_rpl_sr_hdr srh[0];
};
Similarly:
net//ipv6/rpl.c:10: warning: Function parameter or member 'x' not described in 'IPV6_PFXTAIL_LEN'
where IPV6_PFXTAIL_LEN is a macro definition, not a function.
Convert the header comments to a plain /* comment.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028013123.931816-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 01:27:03 +0000 (02:27 +0100)]
net: ipv4: Fix some kerneldoc warnings in TCP Low Priority
net//ipv4/tcp_lp.c:120: warning: Function parameter or member 'sk' not described in 'tcp_lp_cong_avoid'
net//ipv4/tcp_lp.c:135: warning: Function parameter or member 'sk' not described in 'tcp_lp_remote_hz_estimator'
net//ipv4/tcp_lp.c:188: warning: Function parameter or member 'sk' not described in 'tcp_lp_owd_calculator'
net//ipv4/tcp_lp.c:222: warning: Function parameter or member 'rtt' not described in 'tcp_lp_rtt_sample'
net//ipv4/tcp_lp.c:222: warning: Function parameter or member 'sk' not described in 'tcp_lp_rtt_sample'
net//ipv4/tcp_lp.c:265: warning: Function parameter or member 'sk' not described in 'tcp_lp_pkts_acked'
net//ipv4/tcp_lp.c:97: warning: Function parameter or member 'sk' not described in 'tcp_lp_init'
There are still a few kerneldoc warnings after this fix.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028012703.931632-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 01:14:12 +0000 (02:14 +0100)]
net: dccp: Fix most of the kerneldoc warnings
net/dccp/ccids/ccid2.c:190: warning: Function parameter or member 'hc' not described in 'ccid2_update_used_window'
net/dccp/ccids/ccid2.c:190: warning: Function parameter or member 'new_wnd' not described in 'ccid2_update_used_window'
net/dccp/ccids/ccid2.c:360: warning: Function parameter or member 'sk' not described in 'ccid2_rtt_estimator'
net/dccp/ccids/ccid3.c:112: warning: Function parameter or member 'sk' not described in 'ccid3_hc_tx_update_x'
net/dccp/ccids/ccid3.c:159: warning: Function parameter or member 'hc' not described in 'ccid3_hc_tx_update_s'
net/dccp/ccids/ccid3.c:268: warning: Function parameter or member 'sk' not described in 'ccid3_hc_tx_send_packet'
net/dccp/ccids/ccid3.c:667: warning: Function parameter or member 'sk' not described in 'ccid3_first_li'
net/dccp/ccids/ccid3.c:85: warning: Function parameter or member 'hc' not described in 'ccid3_update_send_interval'
net/dccp/ccids/lib/loss_interval.c:85: warning: Function parameter or member 'lh' not described in 'tfrc_lh_update_i_mean'
net/dccp/ccids/lib/loss_interval.c:85: warning: Function parameter or member 'skb' not described in 'tfrc_lh_update_i_mean'
net/dccp/ccids/lib/packet_history.c:392: warning: Function parameter or member 'h' not described in 'tfrc_rx_hist_sample_rtt'
net/dccp/ccids/lib/packet_history.c:392: warning: Function parameter or member 'skb' not described in 'tfrc_rx_hist_sample_rtt'
net/dccp/feat.c:1003: warning: Function parameter or member 'dreq' not described in 'dccp_feat_server_ccid_dependencies'
net/dccp/feat.c:1040: warning: Function parameter or member 'array_len' not described in 'dccp_feat_prefer'
net/dccp/feat.c:1040: warning: Function parameter or member 'array' not described in 'dccp_feat_prefer'
net/dccp/feat.c:1040: warning: Function parameter or member 'preferred_value' not described in 'dccp_feat_prefer'
net/dccp/output.c:151: warning: Function parameter or member 'dp' not described in 'dccp_determine_ccmps'
net/dccp/output.c:242: warning: Function parameter or member 'sk' not described in 'dccp_xmit_packet'
net/dccp/output.c:305: warning: Function parameter or member 'sk' not described in 'dccp_flush_write_queue'
net/dccp/output.c:305: warning: Function parameter or member 'time_budget' not described in 'dccp_flush_write_queue'
net/dccp/output.c:378: warning: Function parameter or member 'sk' not described in 'dccp_retransmit_skb'
net/dccp/qpolicy.c:88: warning: Function parameter or member '' not described in 'dccp_qpolicy_operations'
net/dccp/qpolicy.c:88: warning: Function parameter or member '{' not described in 'dccp_qpolicy_operations'
net/dccp/qpolicy.c:88: warning: Function parameter or member 'params' not described in 'dccp_qpolicy_operations'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028011412.931250-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 01:09:13 +0000 (02:09 +0100)]
net: dcb: Fix kerneldoc warnings
net//dcb/dcbnl.c:1836: warning: Function parameter or member 'app' not described in 'dcb_getapp'
net//dcb/dcbnl.c:1836: warning: Function parameter or member 'dev' not described in 'dcb_getapp'
net//dcb/dcbnl.c:1858: warning: Function parameter or member 'dev' not described in 'dcb_setapp'
net//dcb/dcbnl.c:1858: warning: Function parameter or member 'new' not described in 'dcb_setapp'
net//dcb/dcbnl.c:1899: warning: Function parameter or member 'app' not described in 'dcb_ieee_getapp_mask'
net//dcb/dcbnl.c:1899: warning: Function parameter or member 'dev' not described in 'dcb_ieee_getapp_mask'
net//dcb/dcbnl.c:1922: warning: Function parameter or member 'dev' not described in 'dcb_ieee_setapp'
net//dcb/dcbnl.c:1922: warning: Function parameter or member 'new' not described in 'dcb_ieee_setapp'
net//dcb/dcbnl.c:1953: warning: Function parameter or member 'del' not described in 'dcb_ieee_delapp'
net//dcb/dcbnl.c:1953: warning: Function parameter or member 'dev' not described in 'dcb_ieee_delapp'
net//dcb/dcbnl.c:1986: warning: Function parameter or member 'dev' not described in 'dcb_ieee_getapp_prio_dscp_mask_map'
net//dcb/dcbnl.c:1986: warning: Function parameter or member 'p_map' not described in 'dcb_ieee_getapp_prio_dscp_mask_map'
net//dcb/dcbnl.c:2016: warning: Function parameter or member 'dev' not described in 'dcb_ieee_getapp_dscp_prio_mask_map'
net//dcb/dcbnl.c:2016: warning: Function parameter or member 'p_map' not described in 'dcb_ieee_getapp_dscp_prio_mask_map'
net//dcb/dcbnl.c:2045: warning: Function parameter or member 'dev' not described in 'dcb_ieee_getapp_default_prio_mask'
For some of these warnings, change to comments to plain comments,
since no attempt is being made to follow kerneldoc syntax.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028010913.930929-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 00:56:53 +0000 (01:56 +0100)]
net: nfc: Fix kerneldoc warnings
net//nfc/core.c:1046: warning: Function parameter or member 'tx_headroom' not described in 'nfc_allocate_device'
net//nfc/core.c:1046: warning: Function parameter or member 'tx_tailroom' not described in 'nfc_allocate_device'
net//nfc/core.c:198: warning: Excess function parameter 'protocols' description in 'nfc_start_poll'
net//nfc/core.c:198: warning: Function parameter or member 'im_protocols' not described in 'nfc_start_poll'
net//nfc/core.c:198: warning: Function parameter or member 'tm_protocols' not described in 'nfc_start_poll'
net//nfc/core.c:441: warning: Function parameter or member 'mode' not described in 'nfc_deactivate_target'
net//nfc/core.c:711: warning: Function parameter or member 'dev' not described in 'nfc_alloc_send_skb'
net//nfc/core.c:711: warning: Function parameter or member 'err' not described in 'nfc_alloc_send_skb'
net//nfc/core.c:711: warning: Function parameter or member 'flags' not described in 'nfc_alloc_send_skb'
net//nfc/core.c:711: warning: Function parameter or member 'sk' not described in 'nfc_alloc_send_skb'
net//nfc/digital_core.c:470: warning: Function parameter or member 'im_protocols' not described in 'digital_start_poll'
net//nfc/digital_core.c:470: warning: Function parameter or member 'nfc_dev' not described in 'digital_start_poll'
net//nfc/digital_core.c:470: warning: Function parameter or member 'tm_protocols' not described in 'digital_start_poll'
net//nfc/nci/core.c:1119: warning: Function parameter or member 'tx_headroom' not described in 'nci_allocate_device'
net//nfc/nci/core.c:1119: warning: Function parameter or member 'tx_tailroom' not described in 'nci_allocate_device'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028005653.930467-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 00:55:27 +0000 (01:55 +0100)]
net: appletalk: fix kerneldoc warnings
net/appletalk/aarp.c:68: warning: Function parameter or member 'dev' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'expires_at' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'hwaddr' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'last_sent' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'next' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'packet_queue' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'status' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'target_addr' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'xmit_count' not described in 'aarp_entry'
net/appletalk/ddp.c:1422: warning: Function parameter or member 'dev' not described in 'atalk_rcv'
net/appletalk/ddp.c:1422: warning: Function parameter or member 'orig_dev' not described in 'atalk_rcv'
net/appletalk/ddp.c:1422: warning: Function parameter or member 'pt' not described in 'atalk_rcv'
net/appletalk/ddp.c:1422: warning: Function parameter or member 'skb' not described in 'atalk_rcv'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028005527.930388-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 00:53:50 +0000 (01:53 +0100)]
net: netlabel: Fix kerneldoc warnings
net/netlabel/netlabel_calipso.c:376: warning: Function parameter or member 'ops' not described in 'netlbl_calipso_ops_register'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Paul Moore <paul@paul-moore.com>
Link: https://lore.kernel.org/r/20201028005350.930299-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 00:50:59 +0000 (01:50 +0100)]
net: l3mdev: Fix kerneldoc warning
net/l3mdev/l3mdev.c:249: warning: Function parameter or member 'arg' not described in 'l3mdev_fib_rule_match'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201028005059.930192-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 00:48:49 +0000 (01:48 +0100)]
net: openvswitch: Fix kerneldoc warnings
net/openvswitch/flow.c:303: warning: Function parameter or member 'key_vh' not described in 'parse_vlan_tag'
net/openvswitch/flow.c:303: warning: Function parameter or member 'skb' not described in 'parse_vlan_tag'
net/openvswitch/flow.c:303: warning: Function parameter or member 'untag_vlan' not described in 'parse_vlan_tag'
net/openvswitch/vport.c:122: warning: Function parameter or member 'parms' not described in 'ovs_vport_alloc'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028004849.930094-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 00:46:44 +0000 (01:46 +0100)]
net: llc: Fix kerneldoc warnings
net/llc/llc_conn.c:917: warning: Function parameter or member 'kern' not described in 'llc_sk_alloc'
net/llc/llc_conn.c:917: warning: Function parameter or member 'prot' not described in 'llc_sk_alloc'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028004644.929997-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 30 Oct 2020 18:31:46 +0000 (11:31 -0700)]
Merge branch 'markup-some-printk-like-functions'
Andrew Lunn says:
====================
Markup some printk like functions
W=1 warns of functions which look like printk but don't have
attributes so the compile can check that arguments matches the format
string.
====================
Link: https://lore.kernel.org/r/20201028003849.929490-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 00:38:49 +0000 (01:38 +0100)]
net: tipc: Add __printf() markup to fix -Wsuggest-attribute=format
net/tipc/netlink_compat.c: In function ‘tipc_tlv_sprintf’:
net/tipc/netlink_compat.c:137:2: warning: function ‘tipc_tlv_sprintf’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
137 | n = vscnprintf(buf, rem, fmt, args);
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 00:38:48 +0000 (01:38 +0100)]
net: dccp: Add __printf() markup to fix -Wsuggest-attribute=format
net/dccp/ccid.c: In function ‘ccid_kmem_cache_create’:
net/dccp/ccid.c:85:2: warning: function ‘ccid_kmem_cache_create’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
85 | vsnprintf(slab_name_fmt, CCID_SLAB_NAME_LENGTH, fmt, args);
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn [Wed, 28 Oct 2020 00:43:33 +0000 (01:43 +0100)]
net: tipc: Fix parameter types passed to %s formater
Now that the compiler is performing printf checking, we get the warning:
net/tipc/netlink_compat.c: In function ‘tipc_nl_compat_link_stat_dump’:
net/tipc/netlink_compat.c:591:39: warning: format ‘%s’ expects argument of type ‘char *’, but argument 3 has type ‘void *’ [-Wformat=]
591 | tipc_tlv_sprintf(msg->rep, "\nLink <%s>\n",
| ~^
| |
| char *
| %p
592 | nla_data(link[TIPC_NLA_LINK_NAME]));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| void *
There is no nla_string(), so cast to a char *.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028004333.929816-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 30 Oct 2020 17:50:32 +0000 (10:50 -0700)]
Merge branch 'selftests-net-bridge-add-tests-for-igmpv3'
Nikolay Aleksandrov says:
====================
selftests: net: bridge: add tests for IGMPv3
This set adds tests for the bridge's new IGMPv3 support. The tests use
precooked packets which are sent via mausezahn and the resulting state
after each test is checked for proper X,Y sets, (*,G) source list, source
list entry timers, (S,G) existence and flags, packet forwarding and
blocking, exclude group expiration and (*,G) auto-add. The first 3 patches
prepare the existing IGMPv2 tests, then patch 4 adds new helpers which are
used throughout the rest of the v3 tests.
The following new tests are added:
- base case: IGMPv3 report 239.10.10.10 is_include (A)
- include -> allow report
- include -> is_include report
- include -> is_exclude report
- include -> to_exclude report
- exclude -> allow report
- exclude -> is_include report
- exclude -> is_exclude report
- exclude -> to_exclude report
- include -> block report
- exclude -> block report
- exclude timeout (move to include + entry deletion)
- S,G port entry automatic add to a *,G,exclude port
The variable names and set notation are the same as per RFC 3376,
for more information check RFC 3376 sections 4.2.15 and 6.4.1.
MLDv2 tests will be added by a separate patch-set.
====================
Link: https://lore.kernel.org/r/20201027185934.227040-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:34 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 *,g auto-add
When we have *,G ports in exclude mode and a new S,G,port is added
the kernel has to automatically create an S,G entry for each exclude
port to get proper forwarding.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:33 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 exclude timeout
Test that when a group in exclude mode expires it changes mode to
include and the blocked entries are deleted.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:32 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 exc -> block report
The test checks for the following case:
state report result action
EXCLUDE (X,Y) BLOCK (A) EXCLUDE (X+(A-Y),Y) (A-X-Y)=Group Timer
Send Q(G,A-Y)
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:31 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 inc -> block report
The test checks for the following case:
state report result action
INCLUDE (A) BLOCK (B) INCLUDE (A) Send Q(G,A*B)
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:30 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 exc -> to_exclude report
The test checks for the following case:
state report result action
EXCLUDE (X,Y) TO_EX (A) EXCLUDE (A-Y,Y*A) (A-X-Y)=Group Timer
Delete (X-A)
Delete (Y-A)
Send Q(G,A-Y)
Group Timer=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:29 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 exc -> is_exclude report
The test checks for the following case:
state report result action
EXCLUDE (X,Y) IS_EX (A) EXCLUDE (A-Y,Y*A) (A-X-Y)=GMI
Delete (X-A)
Delete (Y-A)
Group Timer=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:28 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 exc -> is_include report
The test checks for the following case:
state report result action
EXCLUDE (X,Y) IS_IN (A) EXCLUDE (X+A,Y-A) (A)=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:27 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 exc -> allow report
The test checks for the following case:
state report result action
EXCLUDE (X,Y) ALLOW (A) EXCLUDE (X+A,Y-A) (A)=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:26 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 inc -> to_exclude report
The test checks for the following case:
state report result action
INCLUDE (A) TO_EX (B) EXCLUDE (A*B,B-A) (B-A)=0
Delete (A-B)
Send Q(G,A*B)
Group Timer=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:25 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 inc -> is_exclude report
The test checks for the following case:
state report result action
INCLUDE (A) IS_EX (B) EXCLUDE (A*B,B-A) (B-A)=0
Delete (A-B)
Group Timer=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:24 +0000 (20:59 +0200)]
selftests: net: bridge: add test for igmpv3 inc -> is_include report
The test checks for the following case:
state report result action
INCLUDE (A) IS_IN (B) INCLUDE (A+B) (B)=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:23 +0000 (20:59 +0200)]
selftests: net: bridge: add tests for igmpv3 is_include and inc -> allow reports
First we test is_include/include mode then we build on that with allow
effectively achieving:
state report result action
INCLUDE (A) ALLOW (B) INCLUDE (A+B) (B)=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:22 +0000 (20:59 +0200)]
selftests: net: bridge: igmp: add IGMPv3 entries' state helpers
Add helpers which will be used in subsequent tests, they are:
- check_sg_entries: check for proper source list and S,G entry
existence
- check_sg_fwding: check for proper traffic forwarding/blocking
- check_sg_state: check for proper blocked/forwarding entry state
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:21 +0000 (20:59 +0200)]
selftests: net: bridge: igmp: check for specific udp ip protocol
We have to specifically check for udp protocol in addition to the mac
address because in IGMPv3 tests group-specific queries will use the same
mac address.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:20 +0000 (20:59 +0200)]
selftests: net: bridge: igmp: add support for packet source address
Add support for one more argument which specifies the source address to
use. It will be later used for IGMPv3 S,G entry testing.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 27 Oct 2020 18:59:19 +0000 (20:59 +0200)]
selftests: net: bridge: rename current igmp tests to igmpv2
To prepare the bridge_igmp.sh for IGMPv3 we need to rename the
current test to IGMPv2.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andy Shevchenko [Tue, 27 Oct 2020 18:21:46 +0000 (20:21 +0200)]
net: phy: leds: Deduplicate link LED trigger registration
Refactor phy_led_trigger_register() and deduplicate its functionality
when registering LED trigger for link.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201027182146.21355-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vineetha G. Jaya Kumaran [Tue, 27 Oct 2020 16:00:51 +0000 (00:00 +0800)]
net: stmmac: Enable EEE HW LPI timer with auto SW/HW switching
This patch enables the HW LPI Timer which controls the automatic entry
and exit of the LPI state.
The EEE LPI timer value is configured through ethtool. The driver will
auto select the LPI HW timer if the value in the HW timer supported range.
Else, the driver will fallback to SW timer.
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Link: https://lore.kernel.org/r/20201027160051.22898-1-weifeng.voon@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 30 Oct 2020 16:07:37 +0000 (09:07 -0700)]
Merge tag 'wimax-staging' of git://git./linux/kernel/git/arnd/playground
Arnd Bergmann says:
====================
wimax: move to staging
After I sent a fix for what appeared to be a harmless warning in
the wimax user interface code, the conclusion was that the whole
thing has most likely not been used in a very long time, and the
user interface possibly been broken since
b61a5eea5904 ("wimax: use
genl_register_family_with_ops()").
Using a shared branch between net-next and staging should help
coordinate patches getting submitted against it.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jon Maloy [Fri, 30 Oct 2020 01:29:38 +0000 (21:29 -0400)]
tipc: add stricter control of reserved service types
TIPC reserves 64 service types for current and future internal use.
Therefore, the bind() function is meant to block regular user sockets
from being bound to these values, while it should let through such
bindings from internal users.
However, since we at the design moment saw no way to distinguish
between regular and internal users the filter function ended up
with allowing all bindings of the reserved types which were really
in use ([0,1]), and block all the rest ([2,63]).
This is risky, since a regular user may bind to the service type
representing the topology server (TIPC_TOP_SRV == 1) or the one used
for indicating neighboring node status (TIPC_CFG_SRV == 0), and wreak
havoc for users of those services, i.e., most users.
The reality is however that TIPC_CFG_SRV never is bound through the
bind() function, since it doesn't represent a regular socket, and
TIPC_TOP_SRV can also be made to bypass the checks in tipc_bind()
by introducing a different entry function, tipc_sk_bind().
It should be noted that although this is a change of the API semantics,
there is no risk we will break any currently working applications by
doing this. Any application trying to bind to the values in question
would be badly broken from the outset, so there is no chance we would
find any such applications in real-world production systems.
v2: Added warning printout when a user is blocked from binding,
as suggested by Jakub Kicinski
Acked-by: Yung Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/20201030012938.489557-1-jmaloy@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhang Qilong [Tue, 27 Oct 2020 13:51:59 +0000 (21:51 +0800)]
net/mac8390: discard unnecessary breaks
The 'break' is unnecessary because of previous 'return',
and we could discard it.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201027135159.71444-1-zhangqilong3@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Łukasz Stelmach [Tue, 27 Oct 2020 11:43:17 +0000 (12:43 +0100)]
net: mii: Report advertised link capabilities when autonegotiation is off
Unify the set of information returned by mii_ethtool_get_link_ksettings(),
mii_ethtool_gset() and phy_ethtool_ksettings_get(). Make the mii_*()
functions report advertised settings when autonegotiation if disabled.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201027114317.8259-1-l.stelmach@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 30 Oct 2020 01:39:49 +0000 (18:39 -0700)]
Merge branch 'net-bridge-cfm-add-support-for-connectivity-fault-management-cfm'
Henrik Bjoernlund says:
====================
net: bridge: cfm: Add support for Connectivity Fault Management(CFM)
Connectivity Fault Management (CFM) is defined in 802.1Q
section 12.14.
Connectivity Fault Management (CFM) comprises capabilities for
detecting, verifying, and isolating connectivity failures in Virtual
Bridged Networks. These capabilities can be used in networks
operated by multiple independent organizations, each with restricted
management access to each other’s equipment.
CFM functions are partitioned as follows:
— Path discovery
— Fault detection
— Fault verification and isolation
— Fault notification
— Fault recovery
The primary CFM protocol shims are called Maintenance Points (MPs).
A MP can be either a MEP or a MHF.
The MEP:
-It is the Maintenance association End Point
described in 802.1Q section 19.2.
-It is created on a specific level (1-7) and is assuring
that no CFM frames are passing through this MEP on lower levels.
-It initiates and terminates/validates CFM frames on its level.
-It can only exist on a port that is related to a bridge.
The MHF:
-It is the Maintenance Domain Intermediate Point
(MIP) Half Function (MHF) described in 802.1Q section 19.3.
-It is created on a specific level (1-7).
-It is extracting/injecting certain CFM frame on this level.
-It can only exist on a port that is related to a bridge.
-Currently not supported.
There are defined the following CFM protocol functions:
-Continuity Check
-Loopback. Currently not supported.
-Linktrace. Currently not supported.
This CFM component supports create/delete of MEP instances and
configuration of the different CFM protocols. Also status information
can be fetched and delivered through notification due to defect
status change.
The user interacts with CFM using the 'cfm' user space client
program, the client talks with the kernel using netlink.
Any notification emitted by CFM from the kernel can be monitored in
user space by starting 'cfm_server' program.
Currently this 'cfm' and 'cfm_server' programs are standalone placed
in a cfm repository https://github.com/microchip-ung/cfm but it is
considered to integrate this into 'iproute2'.
v1 -> v2
Added the CFM switchdev interface and also added utilization by
calling the interface from the kernel CFM implementation trying
to offload CFM functionality to HW. This offload (CFM driver) is
currently not implemented.
Corrections based on RCF comments:
-The single CFM kernel implementation Patch is broken up into
three patches.
-Changed the list of MEP instances from list_head to
hlist_head.
-Removed unnecessary RCU list traversing.
-Solved RCU unlocking problem.
-Removed unnecessary comments.
-Added ASSERT_RTNL() where required.
-Shaping up on error messages.
-Correction NETLINK br_fill_ifinfo() to be able to handle
'filter_mask' with multiple flags asserted.
v2 -> v3
-The switchdev definition and utilization has been removed as
there was no switchdev implementation.
-Some compiling issues are fixed as Reported-by:
kernel test robot <lkp@intel.com>.
v3 -> v4
-Fixed potential crash during hlist walk where elements are
removed.
-Giving all commits unique titles.
-NETLINK implementation split into three commits.
-Commit "bridge: cfm: Bridge port remove" is merged with
commit "bridge: cfm: Kernel space implementation of CFM. MEP
create/delete."
v4 -> v5
-Reordered members in struct net_bridge to bring member
frame_type_list to the first cache line.
-Helper functions nla_get_mac() and nla_get_maid() are removed.
-The NLA_POLICY_NESTED() macro is used to initialize the
br_cfm_policy array.
-Fixed reverse xmas tree.
v5 -> v6
-Fixed that the SKB buffer was not freed during error handling return.
-Removed unused struct definition.
-Changed bool to u8 bitfields for space save.
-Utilizing the NETLINK policy validation feature.
v6 -> v7
-Removed check of parameters in br_cfm_mep_config_set() and
br_cfm_cc_peer_mep_add() in first commit of MEP implementation
(Patch 4 out of 10)
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
====================
Link: https://lore.kernel.org/r/20201027100251.3241719-1-henrik.bjoernlund@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:51 +0000 (10:02 +0000)]
bridge: cfm: Netlink Notifications.
This is the implementation of Netlink notifications out of CFM.
Notifications are initiated whenever a state change happens in CFM.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_STATUS_INFO:
This indicate that the MEP instance status are following.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO:
This indicate that the peer MEP status are following.
CFM nested attribute has the following attributes in next level.
IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected Opcode.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected version.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN:
The MEP instance received CCM PDU with MD level lower than
configured level. This frame is discarded.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID:
The added Peer MEP ID of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT:
The CCM defect status.
The type is NLA_U32 (bool).
True means no CCM frame is received for 3.25 intervals.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI:
The last received CCM PDU RDI.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE:
The last received CCM PDU Port Status TLV value field.
The type is NLA_U8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE:
The last received CCM PDU Interface Status TLV value field.
The type is NLA_U8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN:
A CCM frame has been received from Peer MEP.
The type is NLA_U32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN:
A CCM frame with TLV has been received from Peer MEP.
The type is NLA_U32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN:
A CCM frame with unexpected sequence number has been received
from Peer MEP.
The type is NLA_U32 (bool).
When a sequence number is not one higher than previously received
then it is unexpected.
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:50 +0000 (10:02 +0000)]
bridge: cfm: Netlink GET status Interface.
This is the implementation of CFM netlink status
get information interface.
Add new nested netlink attributes. These attributes are used by the
user space to get status information.
GETLINK:
Request filter RTEXT_FILTER_CFM_STATUS:
Indicating that CFM status information must be delivered.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_STATUS_INFO:
This indicate that the MEP instance status are following.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO:
This indicate that the peer MEP status are following.
CFM nested attribute has the following attributes in next level.
GETLINK RTEXT_FILTER_CFM_STATUS:
IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected Opcode.
The type is u32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected version.
The type is u32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN:
The MEP instance received CCM PDU with MD level lower than
configured level. This frame is discarded.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID:
The added Peer MEP ID of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT:
The CCM defect status.
The type is u32 (bool).
True means no CCM frame is received for 3.25 intervals.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI:
The last received CCM PDU RDI.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE:
The last received CCM PDU Port Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE:
The last received CCM PDU Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN:
A CCM frame has been received from Peer MEP.
The type is u32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN:
A CCM frame with TLV has been received from Peer MEP.
The type is u32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN:
A CCM frame with unexpected sequence number has been received
from Peer MEP.
The type is u32 (bool).
When a sequence number is not one higher than previously received
then it is unexpected.
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:49 +0000 (10:02 +0000)]
bridge: cfm: Netlink GET configuration Interface.
This is the implementation of CFM netlink configuration
get information interface.
Add new nested netlink attributes. These attributes are used by the
user space to get configuration information.
GETLINK:
Request filter RTEXT_FILTER_CFM_CONFIG:
Indicating that CFM configuration information must be delivered.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_CREATE_INFO:
This indicate that MEP instance create parameters are following.
IFLA_BRIDGE_CFM_MEP_CONFIG_INFO:
This indicate that MEP instance config parameters are following.
IFLA_BRIDGE_CFM_CC_CONFIG_INFO:
This indicate that MEP instance CC functionality
parameters are following.
IFLA_BRIDGE_CFM_CC_RDI_INFO:
This indicate that CC transmitted CCM PDU RDI
parameters are following.
IFLA_BRIDGE_CFM_CC_CCM_TX_INFO:
This indicate that CC transmitted CCM PDU parameters are
following.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INFO:
This indicate that the added peer MEP IDs are following.
CFM nested attribute has the following attributes in next level.
GETLINK RTEXT_FILTER_CFM_CONFIG:
IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE:
The created MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN:
The created MEP domain.
The type is u32 (br_cfm_domain).
It must be BR_CFM_PORT.
This means that CFM frames are transmitted and received
directly on the port - untagged. Not in a VLAN.
IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION:
The created MEP direction.
The type is u32 (br_cfm_mep_direction).
It must be BR_CFM_MEP_DIRECTION_DOWN.
This means that CFM frames are transmitted and received on
the port. Not in the bridge.
IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX:
The created MEP residence port ifindex.
The type is u32 (ifindex).
IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE:
The deleted MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC:
The configured MEP unicast MAC address.
The type is 6*u8 (array).
This is used as SMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL:
The configured MEP unicast MD level.
The type is u32.
It must be in the range 1-7.
No CFM frames are passing through this MEP on lower levels.
IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID:
The configured MEP ID.
The type is u32.
It must be in the range 0-0x1FFF.
This MEP ID is inserted in any transmitted CCM frame.
IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE:
The Continuity Check (CC) functionality is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL:
The CC expected receive interval of CCM frames.
The type is u32 (br_cfm_ccm_interval).
This is also the transmission interval of CCM frames when enabled.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID:
The CC expected receive MAID in CCM frames.
The type is CFM_MAID_LENGTH*u8.
This is MAID is also inserted in transmitted CCM frames.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_MEPID:
The CC Peer MEP ID added.
The type is u32.
When a Peer MEP ID is added and CC is enabled it is expected to
receive CCM frames from that Peer MEP.
IFLA_BRIDGE_CFM_CC_RDI_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_RDI_RDI:
The RDI that is inserted in transmitted CCM PDU.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC:
The transmitted CCM frame destination MAC address.
The type is 6*u8 (array).
This is used as DMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE:
The transmitted CCM frame update (increment) of sequence
number is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD:
The period of time where CCM frame are transmitted.
The type is u32.
The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX
must be done before timeout to keep transmission alive.
When period is zero any ongoing CCM frame transmission
will be stopped.
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV:
The transmitted CCM frame update with Interface Status TLV
is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE:
The transmitted Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV:
The transmitted CCM frame update with Port Status TLV is enabled
or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE:
The transmitted Port Status TLV value field.
The type is u8.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:48 +0000 (10:02 +0000)]
bridge: cfm: Netlink SET configuration Interface.
This is the implementation of CFM netlink configuration
set information interface.
Add new nested netlink attributes. These attributes are used by the
user space to create/delete/configure CFM instances.
SETLINK:
IFLA_BRIDGE_CFM:
Indicate that the following attributes are CFM.
IFLA_BRIDGE_CFM_MEP_CREATE:
This indicate that a MEP instance must be created.
IFLA_BRIDGE_CFM_MEP_DELETE:
This indicate that a MEP instance must be deleted.
IFLA_BRIDGE_CFM_MEP_CONFIG:
This indicate that a MEP instance must be configured.
IFLA_BRIDGE_CFM_CC_CONFIG:
This indicate that a MEP instance Continuity Check (CC)
functionality must be configured.
IFLA_BRIDGE_CFM_CC_PEER_MEP_ADD:
This indicate that a CC Peer MEP must be added.
IFLA_BRIDGE_CFM_CC_PEER_MEP_REMOVE:
This indicate that a CC Peer MEP must be removed.
IFLA_BRIDGE_CFM_CC_CCM_TX:
This indicate that the CC transmitted CCM PDU must be configured.
IFLA_BRIDGE_CFM_CC_RDI:
This indicate that the CC transmitted CCM PDU RDI must be
configured.
CFM nested attribute has the following attributes in next level.
SETLINK RTEXT_FILTER_CFM_CONFIG:
IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE:
The created MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN:
The created MEP domain.
The type is u32 (br_cfm_domain).
It must be BR_CFM_PORT.
This means that CFM frames are transmitted and received
directly on the port - untagged. Not in a VLAN.
IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION:
The created MEP direction.
The type is u32 (br_cfm_mep_direction).
It must be BR_CFM_MEP_DIRECTION_DOWN.
This means that CFM frames are transmitted and received on
the port. Not in the bridge.
IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX:
The created MEP residence port ifindex.
The type is u32 (ifindex).
IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE:
The deleted MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC:
The configured MEP unicast MAC address.
The type is 6*u8 (array).
This is used as SMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL:
The configured MEP unicast MD level.
The type is u32.
It must be in the range 1-7.
No CFM frames are passing through this MEP on lower levels.
IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID:
The configured MEP ID.
The type is u32.
It must be in the range 0-0x1FFF.
This MEP ID is inserted in any transmitted CCM frame.
IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE:
The Continuity Check (CC) functionality is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL:
The CC expected receive interval of CCM frames.
The type is u32 (br_cfm_ccm_interval).
This is also the transmission interval of CCM frames when enabled.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID:
The CC expected receive MAID in CCM frames.
The type is CFM_MAID_LENGTH*u8.
This is MAID is also inserted in transmitted CCM frames.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_MEPID:
The CC Peer MEP ID added.
The type is u32.
When a Peer MEP ID is added and CC is enabled it is expected to
receive CCM frames from that Peer MEP.
IFLA_BRIDGE_CFM_CC_RDI_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_RDI_RDI:
The RDI that is inserted in transmitted CCM PDU.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC:
The transmitted CCM frame destination MAC address.
The type is 6*u8 (array).
This is used as DMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE:
The transmitted CCM frame update (increment) of sequence
number is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD:
The period of time where CCM frame are transmitted.
The type is u32.
The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX
must be done before timeout to keep transmission alive.
When period is zero any ongoing CCM frame transmission
will be stopped.
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV:
The transmitted CCM frame update with Interface Status TLV
is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE:
The transmitted Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV:
The transmitted CCM frame update with Port Status TLV is enabled
or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE:
The transmitted Port Status TLV value field.
The type is u8.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:47 +0000 (10:02 +0000)]
bridge: cfm: Kernel space implementation of CFM. CCM frame RX added.
This is the third commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
Functionality is extended with CCM frame reception.
The MEP instance now contains CCM based status information.
Most important is the CCM defect status indicating if correct
CCM frames are received with the expected interval.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:46 +0000 (10:02 +0000)]
bridge: cfm: Kernel space implementation of CFM. CCM frame TX added.
This is the second commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
Functionality is extended with CCM frame transmission.
Interface is extended with these functions:
br_cfm_cc_rdi_set()
br_cfm_cc_ccm_tx()
br_cfm_cc_config_set()
A MEP Continuity Check feature can be configured by
br_cfm_cc_config_set()
The Continuity Check parameters can be configured to be used when
transmitting CCM.
A MEP can be configured to start or stop transmission of CCM frames by
br_cfm_cc_ccm_tx()
The CCM will be transmitted for a selected period in seconds.
Must call this function before timeout to keep transmission alive.
A MEP transmitting CCM can be configured with inserted RDI in PDU by
br_cfm_cc_rdi_set()
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:45 +0000 (10:02 +0000)]
bridge: cfm: Kernel space implementation of CFM. MEP create/delete.
This is the first commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
It contains MEP instance create, delete and configuration.
Connectivity Fault Management (CFM) comprises capabilities for
detecting, verifying, and isolating connectivity failures in
Virtual Bridged Networks. These capabilities can be used in
networks operated by multiple independent organizations, each
with restricted management access to each others equipment.
CFM functions are partitioned as follows:
- Path discovery
- Fault detection
- Fault verification and isolation
- Fault notification
- Fault recovery
Interface consists of these functions:
br_cfm_mep_create()
br_cfm_mep_delete()
br_cfm_mep_config_set()
br_cfm_cc_config_set()
br_cfm_cc_peer_mep_add()
br_cfm_cc_peer_mep_remove()
A MEP instance is created by br_cfm_mep_create()
-It is the Maintenance association End Point
described in 802.1Q section 19.2.
-It is created on a specific level (1-7) and is assuring
that no CFM frames are passing through this MEP on lower levels.
-It initiates and validates CFM frames on its level.
-It can only exist on a port that is related to a bridge.
-Attributes given cannot be changed until the instance is
deleted.
A MEP instance can be deleted by br_cfm_mep_delete().
A created MEP instance has attributes that can be
configured by br_cfm_mep_config_set().
A MEP Continuity Check feature can be configured by
br_cfm_cc_config_set()
The Continuity Check Receiver state machine can be
enabled and disabled.
According to 802.1Q section 19.2.8
A MEP can have Peer MEPs added and removed by
br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove()
The Continuity Check feature can maintain connectivity
status on each added Peer MEP.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:44 +0000 (10:02 +0000)]
bridge: uapi: cfm: Added EtherType used by the CFM protocol.
This EtherType is used by all CFM protocal frames transmitted
according to 802.1Q section 12.14.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:43 +0000 (10:02 +0000)]
bridge: cfm: Add BRIDGE_CFM to Kconfig.
This makes it possible to include or exclude the CFM
protocol according to 802.1Q section 12.14.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund [Tue, 27 Oct 2020 10:02:42 +0000 (10:02 +0000)]
net: bridge: extend the process of special frames
This patch extends the processing of frames in the bridge. Currently MRP
frames needs special processing and the current implementation doesn't
allow a nice way to process different frame types. Therefore try to
improve this by adding a list that contains frame types that need
special processing. This list is iterated for each input frame and if
there is a match based on frame type then these functions will be called
and decide what to do with the frame. It can process the frame then the
bridge doesn't need to do anything or don't process so then the bridge
will do normal forwarding.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 30 Oct 2020 00:43:23 +0000 (17:43 -0700)]
Merge branch 'vsock-minor-clean-up-of-ioctl-error-handling'
Colin Ian King says:
====================
vsock: minor clean up of ioctl error handling
Two minor changes to the ioctl error handling.
====================
Link: https://lore.kernel.org/r/20201027090942.14916-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Ian King [Tue, 27 Oct 2020 09:09:42 +0000 (09:09 +0000)]
vsock: fix the error return when an invalid ioctl command is used
Currently when an invalid ioctl command is used the error return
is -EINVAL. Fix this by returning the correct error -ENOIOCTLCMD.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Ian King [Tue, 27 Oct 2020 09:09:41 +0000 (09:09 +0000)]
vsock: remove ratelimit unknown ioctl message
When exercising the kernel with stress-ng with some ioctl tests the
"Unknown ioctl" error message is spamming the kernel log at a high
rate. Remove this message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 29 Oct 2020 21:08:40 +0000 (14:08 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 29 Oct 2020 20:02:52 +0000 (13:02 -0700)]
Merge tag 'fallthrough-fixes-clang-5.10-rc2' of git://git./linux/kernel/git/gustavoars/linux
Pull fallthrough fix from Gustavo A. R. Silva:
"This fixes a ton of fall-through warnings when building with Clang
12.0.0 and -Wimplicit-fallthrough"
* tag 'fallthrough-fixes-clang-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
include: jhash/signal: Fix fall-through warnings for Clang
Linus Torvalds [Thu, 29 Oct 2020 19:55:02 +0000 (12:55 -0700)]
Merge tag 'net-5.10-rc2' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release regressions:
- r8169: fix forced threading conflicting with other shared
interrupts; we tried to fix the use of raise_softirq_irqoff from an
IRQ handler on RT by forcing hard irqs, but this driver shares
legacy PCI IRQs so drop the _irqoff() instead
- tipc: fix memory leak caused by a recent syzbot report fix to
tipc_buf_append()
Current release - bugs in new features:
- devlink: Unlock on error in dumpit() and fix some error codes
- net/smc: fix null pointer dereference in smc_listen_decline()
Previous release - regressions:
- tcp: Prevent low rmem stalls with SO_RCVLOWAT.
- net: protect tcf_block_unbind with block lock
- ibmveth: Fix use of ibmveth in a bridge; the self-imposed filtering
to only send legal frames to the hypervisor was too strict
- net: hns3: Clear the CMDQ registers before unmapping BAR region;
incorrect cleanup order was leading to a crash
- bnxt_en - handful of fixes to fixes:
- Send HWRM_FUNC_RESET fw command unconditionally, even if there
are PCIe errors being reported
- Check abort error state in bnxt_open_nic().
- Invoke cancel_delayed_work_sync() for PFs also.
- Fix regression in workqueue cleanup logic in bnxt_remove_one().
- mlxsw: Only advertise link modes supported by both driver and
device, after removal of 56G support from the driver 56G was not
cleared from advertised modes
- net/smc: fix suppressed return code
Previous release - always broken:
- netem: fix zero division in tabledist, caused by integer overflow
- bnxt_en: Re-write PCI BARs after PCI fatal error.
- cxgb4: set up filter action after rewrites
- net: ipa: command payloads already mapped
Misc:
- s390/ism: fix incorrect system EID, it's okay to change since it
was added in current release
- vsock: use ns_capable_noaudit() on socket create to suppress false
positive audit messages"
* tag 'net-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (36 commits)
r8169: fix issue with forced threading in combination with shared interrupts
netem: fix zero division in tabledist
ibmvnic: fix ibmvnic_set_mac
mptcp: add missing memory scheduling in the rx path
tipc: fix memory leak caused by tipc_buf_append()
gtp: fix an use-before-init in gtp_newlink()
net: protect tcf_block_unbind with block lock
ibmveth: Fix use of ibmveth in a bridge.
net/sched: act_mpls: Add softdep on mpls_gso.ko
ravb: Fix bit fields checking in ravb_hwtstamp_get()
devlink: Unlock on error in dumpit()
devlink: Fix some error codes
chelsio/chtls: fix memory leaks in CPL handlers
chelsio/chtls: fix deadlock issue
net: hns3: Clear the CMDQ registers before unmapping BAR region
bnxt_en: Send HWRM_FUNC_RESET fw command unconditionally.
bnxt_en: Check abort error state in bnxt_open_nic().
bnxt_en: Re-write PCI BARs after PCI fatal error.
bnxt_en: Invoke cancel_delayed_work_sync() for PFs also.
bnxt_en: Fix regression in workqueue cleanup logic in bnxt_remove_one().
...
Linus Torvalds [Thu, 29 Oct 2020 18:50:59 +0000 (11:50 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"The good news is people are testing rc1 in the RDMA world - the bad
news is testing of the for-next area is not as good as I had hoped, as
we really should have caught at least the rdma_connect_locked() issue
before now.
Notable merge window regressions that didn't get caught/fixed in time
for rc1:
- Fix in kernel users of rxe, they were broken by the rapid fix to
undo the uABI breakage in rxe from another patch
- EFA userspace needs to read the GID table but was broken with the
new GID table logic
- Fix user triggerable deadlock in mlx5 using devlink reload
- Fix deadlock in several ULPs using rdma_connect from the CM handler
callbacks
- Memory leak in qedr"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/qedr: Fix memory leak in iWARP CM
RDMA: Add rdma_connect_locked()
RDMA/uverbs: Fix false error in query gid IOCTL
RDMA/mlx5: Fix devlink deadlock on net namespace deletion
RDMA/rxe: Fix small problem in network_type patch
Heiner Kallweit [Thu, 29 Oct 2020 09:18:53 +0000 (10:18 +0100)]
r8169: fix issue with forced threading in combination with shared interrupts
As reported by Serge flag IRQF_NO_THREAD causes an error if the
interrupt is actually shared and the other driver(s) don't have this
flag set. This situation can occur if a PCI(e) legacy interrupt is
used in combination with forced threading.
There's no good way to deal with this properly, therefore we have to
remove flag IRQF_NO_THREAD. For fixing the original forced threading
issue switch to napi_schedule().
Fixes:
424a646e072a ("r8169: fix operation under forced interrupt threading")
Link: https://www.spinics.net/lists/netdev/msg694960.html
Reported-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Link: https://lore.kernel.org/r/b5b53bfe-35ac-3768-85bf-74d1290cf394@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aleksandr Nogikh [Wed, 28 Oct 2020 17:07:31 +0000 (17:07 +0000)]
netem: fix zero division in tabledist
Currently it is possible to craft a special netlink RTM_NEWQDISC
command that can result in jitter being equal to 0x80000000. It is
enough to set the 32 bit jitter to 0x02000000 (it will later be
multiplied by 2^6) or just set the 64 bit jitter via
TCA_NETEM_JITTER64. This causes an overflow during the generation of
uniformly distributed numbers in tabledist(), which in turn leads to
division by zero (sigma != 0, but sigma * 2 is 0).
The related fragment of code needs 32-bit division - see commit
9b0ed89 ("netem: remove unnecessary 64 bit modulus"), so switching to
64 bit is not an option.
Fix the issue by keeping the value of jitter within the range that can
be adequately handled by tabledist() - [0;INT_MAX]. As negative std
deviation makes no sense, take the absolute value of the passed value
and cap it at INT_MAX. Inside tabledist(), switch to unsigned 32 bit
arithmetic in order to prevent overflows.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Aleksandr Nogikh <nogikh@google.com>
Reported-by: syzbot+ec762a6342ad0d3c0d8f@syzkaller.appspotmail.com
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/20201028170731.1383332-1-aleksandrnogikh@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lijun Pan [Tue, 27 Oct 2020 22:04:56 +0000 (17:04 -0500)]
ibmvnic: fix ibmvnic_set_mac
Jakub Kicinski brought up a concern in ibmvnic_set_mac().
ibmvnic_set_mac() does this:
ether_addr_copy(adapter->mac_addr, addr->sa_data);
if (adapter->state != VNIC_PROBED)
rc = __ibmvnic_set_mac(netdev, addr->sa_data);
So if state == VNIC_PROBED, the user can assign an invalid address to
adapter->mac_addr, and ibmvnic_set_mac() will still return 0.
The fix is to validate ethernet address at the beginning of
ibmvnic_set_mac(), and move the ether_addr_copy to
the case of "adapter->state != VNIC_PROBED".
Fixes:
c26eba03e407 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201027220456.71450-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arnd Bergmann [Tue, 27 Oct 2020 20:12:12 +0000 (21:12 +0100)]
wimax: move out to staging
There are no known users of this driver as of October 2020, and it will
be removed unless someone turns out to still need it in future releases.
According to https://en.wikipedia.org/wiki/List_of_WiMAX_networks, there
have been many public wimax networks, but it appears that many of these
have migrated to LTE or discontinued their service altogether.
As most PCs and phones lack WiMAX hardware support, the remaining
networks tend to use standalone routers. These almost certainly
run Linux, but not a modern kernel or the mainline wimax driver stack.
NetworkManager appears to have dropped userspace support in 2015
https://bugzilla.gnome.org/show_bug.cgi?id=747846, the
www.linuxwimax.org
site had already shut down earlier.
WiMax is apparently still being deployed on airport campus networks
("AeroMACS"), but in a frequency band that was not supported by the old
Intel 2400m (used in Sandy Bridge laptops and earlier), which is the
only driver using the kernel's wimax stack.
Move all files into drivers/staging/wimax, including the uapi header
files and documentation, to make it easier to remove it when it gets
to that. Only minimal changes are made to the source files, in order
to make it possible to port patches across the move.
Also remove the MAINTAINERS entry that refers to a broken mailing
list and website.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-By: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Suggested-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Sun, 18 Oct 2020 18:00:13 +0000 (20:00 +0200)]
wimax: fix duplicate initializer warning
gcc -Wextra points out multiple fields that use the same index '1'
in the wimax_gnl_policy definition:
net/wimax/stack.c:393:29: warning: initialized field overwritten [-Woverride-init]
net/wimax/stack.c:397:28: warning: initialized field overwritten [-Woverride-init]
net/wimax/stack.c:398:26: warning: initialized field overwritten [-Woverride-init]
This seems to work since all four use the same NLA_U32 value, but it
still appears to be wrong. In addition, there is no intializer for
WIMAX_GNL_MSG_PIPE_NAME, which uses the same index '2' as
WIMAX_GNL_RFKILL_STATE.
Johannes already changed this twice to improve it, but I don't think
there is a good solution, so try to work around it by using a
numeric index and adding comments.
Fixes:
3b0f31f2b8c9 ("genetlink: make policy common to family")
Fixes:
b61a5eea5904 ("wimax: use genl_register_family_with_ops()")
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Paolo Abeni [Tue, 27 Oct 2020 14:59:14 +0000 (15:59 +0100)]
mptcp: add missing memory scheduling in the rx path
When moving the skbs from the subflow into the msk receive
queue, we must schedule there the required amount of memory.
Try to borrow the required memory from the subflow, if needed,
so that we leverage the existing TCP heuristic.
Fixes:
6771bfd9ee24 ("mptcp: update mptcp ack sequence from work queue")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Link: https://lore.kernel.org/r/f6143a6193a083574f11b00dbf7b5ad151bc4ff4.1603810630.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gustavo A. R. Silva [Thu, 3 Sep 2020 04:25:55 +0000 (23:25 -0500)]
include: jhash/signal: Fix fall-through warnings for Clang
In preparation to enable -Wimplicit-fallthrough for Clang, explicitly
add break statements instead of letting the code fall through to the
next case.
This patch adds four break statements that, together, fix almost 40,000
warnings when building Linux 5.10-rc1 with Clang 12.0.0 and this[1] change
reverted. Notice that in order to enable -Wimplicit-fallthrough for Clang,
such change[1] is meant to be reverted at some point. So, this patch helps
to move in that direction.
Something important to mention is that there is currently a discrepancy
between GCC and Clang when dealing with switch fall-through to empty case
statements or to cases that only contain a break/continue/return
statement[2][3][4].
Now that the -Wimplicit-fallthrough option has been globally enabled[5],
any compiler should really warn on missing either a fallthrough annotation
or any of the other case-terminating statements (break/continue/return/
goto) when falling through to the next case statement. Making exceptions
to this introduces variation in case handling which may continue to lead
to bugs, misunderstandings, and a general lack of robustness. The point
of enabling options like -Wimplicit-fallthrough is to prevent human error
and aid developers in spotting bugs before their code is even built/
submitted/committed, therefore eliminating classes of bugs. So, in order
to really accomplish this, we should, and can, move in the direction of
addressing any error-prone scenarios and get rid of the unintentional
fallthrough bug-class in the kernel, entirely, even if there is some minor
redundancy. Better to have explicit case-ending statements than continue to
have exceptions where one must guess as to the right result. The compiler
will eliminate any actual redundancy.
[1] commit
e2079e93f562c ("kbuild: Do not enable -Wimplicit-fallthrough for clang for now")
[2] https://github.com/ClangBuiltLinux/linux/issues/636
[3] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=91432
[4] https://godbolt.org/z/xgkvIh
[5] commit
a035d552a93b ("Makefile: Globally enable fall-through warning")
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Linus Torvalds [Thu, 29 Oct 2020 17:13:09 +0000 (10:13 -0700)]
Merge tag 'afs-fixes-
20201029' of git://git./linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
- Fix copy_file_range() to an afs file now returning EINVAL if the
splice_write file op isn't supplied.
- Fix a deref-before-check in afs_unuse_cell().
- Fix a use-after-free in afs_xattr_get_acl().
- Fix afs to not try to clear PG_writeback when laundering a page.
- Fix afs to take a ref on a page that it sets PG_private on and to
drop that ref when clearing PG_private. This is done through recently
added helpers.
- Fix a page leak if write_begin() fails.
- Fix afs_write_begin() to not alter the dirty region info stored in
page->private, but rather do this in afs_write_end() instead when we
know what we actually changed.
- Fix afs_invalidatepage() to alter the dirty region info on a page
when partial page invalidation occurs so that we don't inadvertantly
include a span of zeros that will get written back if a page gets
laundered due to a remote 3rd-party induced invalidation.
We mustn't, however, reduce the dirty region if the page has been
seen to be mapped (ie. we got called through the page_mkwrite vector)
as the page might still be mapped and we might lose data if the file
is extended again.
- Fix the dirty region info to have a lower resolution if the size of
the page is too large for this to be encoded (e.g. powerpc32 with 64K
pages).
Note that this might not be the ideal way to handle this, since it
may allow some leakage of undirtied zero bytes to the server's copy
in the case of a 3rd-party conflict.
To aid the last two fixes, two additional changes:
- Wrap the manipulations of the dirty region info stored in
page->private into helper functions.
- Alter the encoding of the dirty region so that the region bounds can
be stored with one fewer bit, making a bit available for the
indication of mappedness.
* tag 'afs-fixes-
20201029' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix dirty-region encoding on ppc32 with 64K pages
afs: Fix afs_invalidatepage to adjust the dirty region
afs: Alter dirty range encoding in page->private
afs: Wrap page->private manipulations in inline functions
afs: Fix where page->private is set during write
afs: Fix page leak on afs_write_begin() failure
afs: Fix to take ref on page when PG_private is set
afs: Fix afs_launder_page to not clear PG_writeback
afs: Fix a use after free in afs_xattr_get_acl()
afs: Fix tracing deref-before-check
afs: Fix copy_file_range()
Tung Nguyen [Tue, 27 Oct 2020 03:24:03 +0000 (10:24 +0700)]
tipc: fix memory leak caused by tipc_buf_append()
Commit
ed42989eab57 ("tipc: fix the skb_unshare() in tipc_buf_append()")
replaced skb_unshare() with skb_copy() to not reduce the data reference
counter of the original skb intentionally. This is not the correct
way to handle the cloned skb because it causes memory leak in 2
following cases:
1/ Sending multicast messages via broadcast link
The original skb list is cloned to the local skb list for local
destination. After that, the data reference counter of each skb
in the original list has the value of 2. This causes each skb not
to be freed after receiving ACK:
tipc_link_advance_transmq()
{
...
/* release skb */
__skb_unlink(skb, &l->transmq);
kfree_skb(skb); <-- memory exists after being freed
}
2/ Sending multicast messages via replicast link
Similar to the above case, each skb cannot be freed after purging
the skb list:
tipc_mcast_xmit()
{
...
__skb_queue_purge(pkts); <-- memory exists after being freed
}
This commit fixes this issue by using skb_unshare() instead. Besides,
to avoid use-after-free error reported by KASAN, the pointer to the
fragment is set to NULL before calling skb_unshare() to make sure that
the original skb is not freed after freeing the fragment 2 times in
case skb_unshare() returns NULL.
Fixes:
ed42989eab57 ("tipc: fix the skb_unshare() in tipc_buf_append()")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Reported-by: Thang Hoang Ngo <thang.h.ngo@dektech.com.au>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/r/20201027032403.1823-1-tung.q.nguyen@dektech.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Masahiro Fujiwara [Tue, 27 Oct 2020 11:48:46 +0000 (20:48 +0900)]
gtp: fix an use-before-init in gtp_newlink()
*_pdp_find() from gtp_encap_recv() would trigger a crash when a peer
sends GTP packets while creating new GTP device.
RIP: 0010:gtp1_pdp_find.isra.0+0x68/0x90 [gtp]
<SNIP>
Call Trace:
<IRQ>
gtp_encap_recv+0xc2/0x2e0 [gtp]
? gtp1_pdp_find.isra.0+0x90/0x90 [gtp]
udp_queue_rcv_one_skb+0x1fe/0x530
udp_queue_rcv_skb+0x40/0x1b0
udp_unicast_rcv_skb.isra.0+0x78/0x90
__udp4_lib_rcv+0x5af/0xc70
udp_rcv+0x1a/0x20
ip_protocol_deliver_rcu+0xc5/0x1b0
ip_local_deliver_finish+0x48/0x50
ip_local_deliver+0xe5/0xf0
? ip_protocol_deliver_rcu+0x1b0/0x1b0
gtp_encap_enable() should be called after gtp_hastable_new() otherwise
*_pdp_find() will access the uninitialized hash table.
Fixes:
1e3a3abd8b28 ("gtp: make GTP sockets in gtp_newlink optional")
Signed-off-by: Masahiro Fujiwara <fujiwara.masahiro@gmail.com>
Link: https://lore.kernel.org/r/20201027114846.3924-1-fujiwara.masahiro@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 29 Oct 2020 16:36:11 +0000 (09:36 -0700)]
Merge tag 'ext4_for_linus_fixes' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Bug fixes for the new ext4 fast commit feature, plus a fix for the
'data=journal' bug fix.
Also use the generic casefolding support which has now landed in
fs/libfs.c for 5.10"
* tag 'ext4_for_linus_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: indicate that fast_commit is available via /sys/fs/ext4/feature/...
ext4: use generic casefolding support
ext4: do not use extent after put_bh
ext4: use IS_ERR() for error checking of path
ext4: fix mmap write protection for data=journal mode
jbd2: fix a kernel-doc markup
ext4: use s_mount_flags instead of s_mount_state for fast commit state
ext4: make num of fast commit blocks configurable
ext4: properly check for dirty state in ext4_inode_datasync_dirty()
ext4: fix double locking in ext4_fc_commit_dentry_updates()
David Howells [Wed, 28 Oct 2020 12:08:39 +0000 (12:08 +0000)]
afs: Fix dirty-region encoding on ppc32 with 64K pages
The dirty region bounds stored in page->private on an afs page are 15 bits
on a 32-bit box and can, at most, represent a range of up to 32K within a
32K page with a resolution of 1 byte. This is a problem for powerpc32 with
64K pages enabled.
Further, transparent huge pages may get up to 2M, which will be a problem
for the afs filesystem on all 32-bit arches in the future.
Fix this by decreasing the resolution. For the moment, a 64K page will
have a resolution determined from PAGE_SIZE. In the future, the page will
need to be passed in to the helper functions so that the page size can be
assessed and the resolution determined dynamically.
Note that this might not be the ideal way to handle this, since it may
allow some leakage of undirtied zero bytes to the server's copy in the case
of a 3rd-party conflict. Fixing that would require a separately allocated
record and is a more complicated fix.
Fixes:
4343d00872e1 ("afs: Get rid of the afs_writeback record")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
David Howells [Thu, 22 Oct 2020 13:08:23 +0000 (14:08 +0100)]
afs: Fix afs_invalidatepage to adjust the dirty region
Fix afs_invalidatepage() to adjust the dirty region recorded in
page->private when truncating a page. If the dirty region is entirely
removed, then the private data is cleared and the page dirty state is
cleared.
Without this, if the page is truncated and then expanded again by truncate,
zeros from the expanded, but no-longer dirty region may get written back to
the server if the page gets laundered due to a conflicting 3rd-party write.
It mustn't, however, shorten the dirty region of the page if that page is
still mmapped and has been marked dirty by afs_page_mkwrite(), so a flag is
stored in page->private to record this.
Fixes:
4343d00872e1 ("afs: Get rid of the afs_writeback record")
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 26 Oct 2020 13:57:44 +0000 (13:57 +0000)]
afs: Alter dirty range encoding in page->private
Currently, page->private on an afs page is used to store the range of
dirtied data within the page, where the range includes the lower bound, but
excludes the upper bound (e.g. 0-1 is a range covering a single byte).
This, however, requires a superfluous bit for the last-byte bound so that
on a 4KiB page, it can say 0-4096 to indicate the whole page, the idea
being that having both numbers the same would indicate an empty range.
This is unnecessary as the PG_private bit is clear if it's an empty range
(as is PG_dirty).
Alter the way the dirty range is encoded in page->private such that the
upper bound is reduced by 1 (e.g. 0-0 is then specified the same single
byte range mentioned above).
Applying this to both bounds frees up two bits, one of which can be used in
a future commit.
This allows the afs filesystem to be compiled on ppc32 with 64K pages;
without this, the following warnings are seen:
../fs/afs/internal.h: In function 'afs_page_dirty_to':
../fs/afs/internal.h:881:15: warning: right shift count >= width of type [-Wshift-count-overflow]
881 | return (priv >> __AFS_PAGE_PRIV_SHIFT) & __AFS_PAGE_PRIV_MASK;
| ^~
../fs/afs/internal.h: In function 'afs_page_dirty':
../fs/afs/internal.h:886:28: warning: left shift count >= width of type [-Wshift-count-overflow]
886 | return ((unsigned long)to << __AFS_PAGE_PRIV_SHIFT) | from;
| ^~
Fixes:
4343d00872e1 ("afs: Get rid of the afs_writeback record")
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 26 Oct 2020 13:22:47 +0000 (13:22 +0000)]
afs: Wrap page->private manipulations in inline functions
The afs filesystem uses page->private to store the dirty range within a
page such that in the event of a conflicting 3rd-party write to the server,
we write back just the bits that got changed locally.
However, there are a couple of problems with this:
(1) I need a bit to note if the page might be mapped so that partial
invalidation doesn't shrink the range.
(2) There aren't necessarily sufficient bits to store the entire range of
data altered (say it's a 32-bit system with 64KiB pages or transparent
huge pages are in use).
So wrap the accesses in inline functions so that future commits can change
how this works.
Also move them out of the tracing header into the in-directory header.
There's not really any need for them to be in the tracing header.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 26 Oct 2020 14:05:33 +0000 (14:05 +0000)]
afs: Fix where page->private is set during write
In afs, page->private is set to indicate the dirty region of a page. This
is done in afs_write_begin(), but that can't take account of whether the
copy into the page actually worked.
Fix this by moving the change of page->private into afs_write_end().
Fixes:
4343d00872e1 ("afs: Get rid of the afs_writeback record")
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Thu, 22 Oct 2020 13:03:03 +0000 (14:03 +0100)]
afs: Fix page leak on afs_write_begin() failure
Fix the leak of the target page in afs_write_begin() when it fails.
Fixes:
15b4650e55e0 ("afs: convert to new aops")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Nick Piggin <npiggin@gmail.com>
David Howells [Wed, 21 Oct 2020 12:22:19 +0000 (13:22 +0100)]
afs: Fix to take ref on page when PG_private is set
Fix afs to take a ref on a page when it sets PG_private on it and to drop
the ref when removing the flag.
Note that in afs_write_begin(), a lot of the time, PG_private is already
set on a page to which we're going to add some data. In such a case, we
leave the bit set and mustn't increment the page count.
As suggested by Matthew Wilcox, use attach/detach_page_private() where
possible.
Fixes:
31143d5d515e ("AFS: implement basic file write support")
Reported-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Linus Torvalds [Wed, 28 Oct 2020 19:05:14 +0000 (12:05 -0700)]
Merge tag 'trace-v5.10-rc1' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix synthetic event "strcat" overrun
New synthetic event code used strcat() and miscalculated the ending,
causing the concatenation to write beyond the allocated memory.
Instead of using strncat(), the code is switched over to seq_buf which
has all the mechanisms in place to protect against writing more than
what is allocated, and cleans up the code a bit"
* tag 'trace-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing, synthetic events: Replace buggy strcat() with seq_buf operations
Theodore Ts'o [Wed, 28 Oct 2020 17:39:13 +0000 (13:39 -0400)]
ext4: indicate that fast_commit is available via /sys/fs/ext4/feature/...
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Daniel Rosenberg [Wed, 28 Oct 2020 05:08:20 +0000 (05:08 +0000)]
ext4: use generic casefolding support
This switches ext4 over to the generic support provided in libfs.
Since casefolded dentries behave the same in ext4 and f2fs, we decrease
the maintenance burden by unifying them, and any optimizations will
immediately apply to both.
Signed-off-by: Daniel Rosenberg <drosen@google.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20201028050820.1636571-1-drosen@google.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
yangerkun [Wed, 28 Oct 2020 05:56:17 +0000 (13:56 +0800)]
ext4: do not use extent after put_bh
ext4_ext_search_right() will read more extent blocks and call put_bh
after we get the information we need. However, ret_ex will break this
and may cause use-after-free once pagecache has been freed. Fix it by
copying the extent structure if needed.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Link: https://lore.kernel.org/r/20201028055617.2569255-1-yangerkun@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Harshad Shirwadkar [Tue, 27 Oct 2020 20:43:42 +0000 (13:43 -0700)]
ext4: use IS_ERR() for error checking of path
With this fix, fast commit recovery code uses IS_ERR() for path
returned by ext4_find_extent.
Fixes:
8016e29f4362 ("ext4: fast commit recovery path")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201027204342.2794949-1-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Jan Kara [Tue, 27 Oct 2020 13:27:51 +0000 (14:27 +0100)]
ext4: fix mmap write protection for data=journal mode
Commit
afb585a97f81 "ext4: data=journal: write-protect pages on
j_submit_inode_data_buffers()") added calls ext4_jbd2_inode_add_write()
to track inode ranges whose mappings need to get write-protected during
transaction commits. However the added calls use wrong start of a range
(0 instead of page offset) and so write protection is not necessarily
effective. Use correct range start to fix the problem.
Fixes:
afb585a97f81 ("ext4: data=journal: write-protect pages on j_submit_inode_data_buffers()")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20201027132751.29858-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Mauro Carvalho Chehab [Tue, 27 Oct 2020 09:51:27 +0000 (10:51 +0100)]
jbd2: fix a kernel-doc markup
The kernel-doc markup that documents _fc_replay_callback is
missing an asterisk, causing this warning:
../include/linux/jbd2.h:1271: warning: Function parameter or member 'j_fc_replay_callback' not described in 'journal_s'
When building the docs.
Fixes:
609f928af48f ("jbd2: fast commit recovery path")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/6055927ada2015b55b413cdd2670533bdc9a8da2.1603791716.git.mchehab+huawei@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Harshad Shirwadkar [Tue, 27 Oct 2020 04:49:15 +0000 (21:49 -0700)]
ext4: use s_mount_flags instead of s_mount_state for fast commit state
Ext4's fast commit related transient states should use
sb->s_mount_flags instead of persistent sb->s_mount_state.
Fixes:
8016e29f4362 ("ext4: fast commit recovery path")
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201027044915.2553163-3-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Harshad Shirwadkar [Tue, 27 Oct 2020 04:49:14 +0000 (21:49 -0700)]
ext4: make num of fast commit blocks configurable
This patch reserves a field in the jbd2 superblock for number of fast
commit blocks. When this value is non-zero, Ext4 uses this field to
set the number of fast commit blocks.
Fixes:
6866d7b3f2bb ("ext4/jbd2: add fast commit initialization")
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Link: https://lore.kernel.org/r/20201027044915.2553163-2-harshadshirwadkar@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
projects / linux-2.6-microblaze.git / log