drm/amd/display: FreeSync not active near lower bound of non-LFC monitor range

[Why]
On narrow range monitors without LFC, a margin prevents good utilization
of the available range.

[How]
Decrease the margin for exiting fixed mode and fix the frame counter to
reset if a non-consecutive render is found.

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix OPTC_DATA_FORMAT programming

This should be programmed with timing rather than with odm.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add i2c speed arbitration for dc_i2c and hdcp_i2c

[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.

[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.

This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.

Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Block ABM in case of eDP ODM

[Why]
enable ODM on eDP panel with ABM will result in color difference
on the panel due to only one ABM module to set one pipe.

[How]
Block ABM in case of ODM enabled on eDP.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Copy WM values from set A to other sets in hw_init

[Why]
When we transfer the WM range table to SMU, they can perform a watermark
switch right away. This can be a problem if we're in not in accelerated mode
during hw_init as SMU may initiate a dummy p-state change before the rest
of the watermarks are programmed. Watermark set A is defined to be
sufficient for all cases, so we can copy the values from set A to all other
sets, avoiding any issues from SMU doing WM switches.

[How]
 - new hubbub func init_watermarks
 - copy register values from set A to all other sets
 - call init_watermarks before calling notify_wm_ranges

Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Force enable pstate on driver unload

[Why]
During driver unload, it is expected that p-state switching is supported.
If it's not supported, PMFW will hang due to a forced p-state switch. Even
if the current timing does not support p-state normally, we still want to
force allow because the worst that can happen is underflow. This will
match Navi10 behaviour.

[How]
 - new hubbub func to control the force pstate register
 - force allow when releasing display ownership
   - registers are inaccessible after due to m_cgs.hwNotAvailable
 - explicitly disable force signal during hw_init
   - if driver is disabled and re-enabled, register not cleared otherwise

Also, remove DCN3 part of dcn10_init_hw, we will not be going back to it.

Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fixed comments (uniform style)

[WHY]
This change was implemented because the comment style was not uniform
across the file. In some lines comments were initiated with // and in
others they were in between /* ... */.
Additionally, the style for multi-line comments was also not uniform and
some comment lines were missing the space between the opening /* and the
first word of the comment.

[HOW]
All comments are now in between /*.../*, multi line comments also use
/*...*/ and for every comment there is now a space between the opening
/* and the first word of the comment.

Signed-off-by: Felipe <Felipe.Clark@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Check for flip pending before locking pipes

[Why]
When running games or benchmarking with v-sync disabled, disabling
a plane (which is v-sync) can cause underflow. This is caused by
flips pending before pipe locking being applied after locks are
released and pipes could have been re-arranged or disconnected. This
could potentially apply a flip on incorrect pipe. Also, previous logic
of always locking pipes was unnecessary.

[How]
Only lock the pipes when there is a pipe being disabled to increase
efficiency. Before the pipes are locked, check that any pending flips
are cleared to ensure the flips are applied to the correct pipe.

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Don't allow pstate if no support in blank

[Why]
We will hang if we report switch in VACTIVE but not in VBLANK and DPG_EN = 1

[How]
Block switch in ACTIVE if not supported in BLANK

Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.105

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add van gogh pci id

Add Van Gogh PCI id support.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add dcn3.01 support to DM

Update dm for vangogh support.

Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add dcn3.01 support to DC (v2)

Update dc for vangogh support.

v2: fix compilation without DCN 301 set.

Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable gfx clock gating and power gating for vangogh

This patch is to enable the gfx cg and pg for vangogh.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add gfx power gating for gfx10

This patch adds power gating handler for gfx10.

v2: simplify function

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/mmhub2.3: print client id string for mmhub

Print the name of the client rather than the number.  This
makes it easier to debug what block is causing the fault.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: IP discovery table is not ready yet for VG

Fallback to legacy path for now.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: disable gfxoff on vangogh for the moment (v2)

GFXOFF will be enabled once it's verified on real asic.

v2: move check into gfx10 module.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable psp support for vangogh

This patch is to enable psp support for vangogh

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add TOC firmware support for apu (v3)

APU needs load toc firmware for gfx10 series on psp front door loading.

v2: rebase against latest code
v3: clarify error message

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add TOC firmware definition

This patch is to add TOC firmware definition on uapi.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add smu ip block for vangogh

This patch is to add ip block for vangogh.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: add vangogh ppt into swSMU

This patch is to add vangogh ppt funcions into swSMU block.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: partially enable swsmu for vangogh

This patch is to partially enable swSMU for vangogh for the moment.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/powerplay: add smu initialize funcitons for vangogh (v4)

This patch is to add smu initialize functions for vangogh.

v2: squash in updates
v3: drop duplicate table entries
v4: rebase fixes

Signed-off-by: Xiaojian Du <xiaojian.du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/powerplay: add vangogh asic name in smu v11 (v2)

This patch is to add vangogh asic name in smu v11.

v2: drop smu firmware name (N/A for VG)

Signed-off-by: Xiaojian Du <xiaojian.du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/powerplay: add smu v11.5 smc header for vangogh

This patch is to add smu v11.5 smc header for vangogh.

Signed-off-by: Xiaojian Du <xiaojian.du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/powerplay: add smu v11.5 firmware header for vangogh (v2)

This patch is to add smu v11.5 firmware header for vangogh

v2: squash in updates

Signed-off-by: Xiaojian Du <xiaojian.du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/admgpu/powerplay: add smu v11.5 driver interface header for vangogh

This patch is to add smu v11.5 driver interface header for vangogh.

Signed-off-by: Xiaojian Du <xiaojian.du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/powerplay: add new smu messages and feature masks for vangogh (v2)

This patch is to add new smu messages and feature masks for vangogh.

v2: squash in updates and typo fixes

Signed-off-by: Xiaojian Du <xiaojian.du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add nbio v7.2 for vangogh (v2)

VanGogh uses nbio v7.2, and a couple of offsets are changed since nbio
v2.3 for navi series, so add new nbio v7.2 block.

v2: squash in fix for sdma and vcn instances

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add pcie port indirect read and write on nv

This patch is to add pcie port indirect read/write callback for nv
series. They will be used for new asic.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable vcn3.0 for van gogh

Same as other VCN 3.0 asics.

Signed-off-by: Thong Thai <thong.thai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add mmhub v2.3 for vangogh (v4)

There are too many register offset mismatch between mmhub v2.0 and v2.3.

E.X:

mmMM_ATC_L2_MISC_CG:  0x064a(v2.0)  0x06cd(v2.3)
mmMMVM_L2_PROTECTION_FAULT_CNTL: 0x0688(v2.0) 0x0708(v2.3)
mmMMVM_CONTEXT0_PAGE_TABLE_BASE_ADDR_LO32: 0x072b(v2.0) 0x0940(v2.3)
mmMMVM_CONTEXT0_PAGE_TABLE_BASE_ADDR_HI32: 0x072c(v2.0) 0x0941(v2.3)
mmMMVM_INVALIDATE_ENG0_REQ: 0x06e3(v2.0) 0x0a01(v2.3)
mmMMVM_INVALIDATE_ENG0_ACK: 0x06f5(v2.0) 0x0a02(v2.3)
mmMMVM_CONTEXT0_CNTL: 0x06c0(v2.0) 0x0740(v2.3)
mmMMVM_L2_PROTECTION_FAULT_STATUS: 0x068c(v2.0) 0x070c(v2.3)
mmMMVM_L2_PROTECTION_FAULT_CNTL: 0x0688(v2.0) 0x0708(v2.3)
mmMM_ATC_L2_MISC_CG: 0x064a(v2.0) 0x06cd(v2.3)
mmDAGB0_CNTL_MISC2: 0x0071(v2.0) 0x0096(v2.3)
...

Continuing using the same file mmhub v2.0 is not good choice, it will
introduce a lot of checking with ASIC types. And also easy to introduce the
issues that offset not align, this kind of issues are really hard to find. Van
Gogh's mmhub vm invalidation is actually caused by the offset mismatch as well.

So it would like to create a new file rather than stick to re-use orignal mmhub
v2.0 here.

v2: add missed translate_further programming.
v3: sync with latest code
v4: add missing callbacks

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: add Van Gogh KFD support

This patch is to add GFX10 based APU Van Gogh KFD support. We will treat Van
Gogh as "dgpu" (bypass IOMMU v2).

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: set ip blocks for van gogh

Enable ip blocks for van gogh.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add sdma support for van gogh

This patch adds the sdma v5.2 support for van gogh.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gfx10: add updated register offsets for VGH

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add gfx golden settings for vangogh (v3)

This patch is to add gfx golden settings for vangogh post si.

v2: squash in updates
v3: fix SPI register offset

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add gfx support for van gogh (v3)

Add van gogh checks to gfx10 code.

v2: squash in fixes
v3: fix mode

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: set fw load type for van gogh

This patch sets fw load type as direct for van gogh for the moment.
Will switch to psp when psp is ready.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add gmc v10 supports for van gogh (v4)

Add gfx memory controller support for van gogh.

v2: don't use dynamic invalidate eng allocation for van gogh.
v3: squash in other fixes
v4: rebase

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: get the correct vram type for van gogh

This patch is to get the correct vram type from atombios for van gogh.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/atomfirmware: Add edp and integrated info v2.1 tables

Required for vangogh.

Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: update new memory types in atomfirmware header

Add new nemory types in atomfirmware header.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add uapi to define van gogh memory type

This patch adds van gogh memory type as DDR5.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use gpu virtual address for interrupt packet write space for vangogh

The interrupts are not stable while uses guest physical address (GPA)
for interrupt packet write space even on direct loading case.

v2: make condition more readable

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add van gogh support for ih block

This patch adds the support for van gogh ih block.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: skip sdma1 in nv_allowed_read_registers list for van gogh (v2)

Van gogh only has one sdma.

v2: use num_instances rather than APU flag

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add nv common ip block support for van gogh

This patch adds common ip support for van gogh.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add vangogh_reg_base_init function for van gogh

This patch adds vangogh_reg_base_init function to init the register base for
van gogh.

v2: make vangogh_reg_base_init void, align equality sign

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add van gogh support for gpu_info and ip block setting

This patch adds van gogh support for gpu_info firmware and ip block setting.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add uapi to define van gogh series

Add a flag to define van gogh series.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add van gogh asic_type enum (v2)

This patch adds van gogh to amd_asic_type enum and amdgpu_asic_name[].

v2: add missing comma

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add vangogh asic header files (v2)

This patch is to add vangogh asic header files.

v2: squash in updates

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: HDMI remote sink need mode validation for Linux

[Why]
Currently mode validation is bypassed if remote sink exists. That
leads to mode set issue when a BW bottle neck exists in the link path,
e.g., a DP-to-HDMI converter that only supports HDMI 1.4.

Any invalid mode passed to Linux user space will cause the modeset
failure due to limitation of Linux user space implementation.

[How]
Mode validation is skipped only if in edid override. For real remote
sink, clock limit check should be done for HDMI remote sink.

Have HDMI related remote sink going through mode validation to
elimiate modes which pixel clock exceeds BW limitation.

Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Change to correct unit on audio rate

[Why]
Formula uses kHz in their formula while our driver operates with Hz.

[How]
Divide audio rate by 1000 on the initial variable that is entered into formula.

Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Avoid set zero in the requested clk

[Why]
Sometimes CRTCs can be disabled due to display unplugging or temporarily
transition in the userspace; in these circumstances, DCE tries to set
the minimum clock threshold. When we have this situation, the function
bw_calcs is invoked with number_of_displays set to zero, making DCE set
dispclk_khz and sclk_khz to zero. For these reasons, we have seen some
ATOM bios errors that look like:

[drm:atom_op_jump [amdgpu]] *ERROR* atombios stuck in loop for more than
5secs aborting
[drm:amdgpu_atom_execute_table_locked [amdgpu]] *ERROR* atombios stuck
executing EA8A (len 761, WS 0, PS 0) @ 0xEABA

[How]
This error happens due to an attempt to optimize the bandwidth using the
sclk, and the dispclk clock set to zero. Technically we handle this in
the function dce112_set_clock, but we are not considering the case that
this value is set to zero. This commit fixes this issue by ensuring that
we never set a minimum value below the minimum clock threshold.

Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: align frag_end to covered address space

align frag_end to the next pd when there are no
page table entries on the current pde.
This fixes invalidation of larger address space areas
where some page tables are allocated and other aren't.

Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix NULL pointer dereference for Renoir

Commit c1cf79ca5ced46 ("drm/amdgpu: use IP discovery table for renoir")
introduced a NULL pointer dereference when booting with
amdgpu.discovery=0, because it removed the call of vega10_reg_base_init()
for that case.

Fix this by calling that funcion if amdgpu_discovery == 0 in addition to
the case that amdgpu_discovery_reg_base_init() failed.

Fixes: c1cf79ca5ced46 ("drm/amdgpu: use IP discovery table for renoir")
Signed-off-by: Dirk Gouders <dirk@gouders.net>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/swsmu: add interrupt work handler for smu11 parts

We need to schedule the smu AC/DC interrupt ack to avoid
potentially sleeping if the smu message mutex is contended.

Fixes: e1188aacad1730 ("drm/amdgpu/smu11: add support for SMU AC/DC interrupts")
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/swsmu: add interrupt work function

So we can schedule work from interrupts.  This might include
long tasks or things that could sleep.

Fixes: e1188aacad1730 ("drm/amdgpu/smu11: add support for SMU AC/DC interrupts")
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable GDDR6 save-restore support for navy_flounder

add mp0 11_0_11 for navy_flounder to the mem training
supported list, otherwise the modeprobe would fail
on navy_flounder with latest vbios.

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: support indirect access reg outside of mmio bar (v2)

support both direct and indirect accessor in unified
helper functions.

v2: Retire indirect mmio access via mm_index/data

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: switch to indirect reg access helper

Switch WREG32/RREG32_PCIE to use indirect reg access
helper for soc15 and onwards

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add helper function for indirect reg access (v3)

Add helper function in order to remove RREG32/WREG32
in current pcie_rreg/wreg function for soc15 and
onwards adapters.
PCIE_INDEX/DATA pairs are used to access regsiters
outside of mmio bar in the helper functions.
The new helper functions help remove the recursion
of amdgpu_mm_rreg/wreg from pcie_rreg/wreg and
provide the oppotunity to centralize direct and
indirect access in a single function.

v2: Fixed typo and refine the comments

v3: Remove unnecessary volatile local variable

Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdkfd: Surface files in Sysfs to allow users to get number of
compute units that are in use.

[Why]
Allow user to know how many compute units (CU) are in use at any given
moment.

[How]
Surface files in Sysfs that allow user to determine the number of compute
units that are in use for a given process. One Sysfs file is used per
device.

Signed-off-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Reviewed-By: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: Define and implement a function that collects number of
waves that are in flight.

[Why]
Allow user to know how many compute units (CU) are in use at any given
moment.

[How]
Read registers of SQ that give number of waves that are in flight
of various queues. Use this information to determine number of CU's
in use.

Signed-off-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Reviewed-By: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: disable gfxoff temporarily for navy_flounder

gfxoff is temporarily disabled for navy_flounder, since
at present the feature caused some tdr when performing
display operations.

Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: drop duplicated ecc check for vega10 (v5)

The same ECC check has been executed in amdgpu_ras_init for vega10,
prior to gmc_v9_0_late_init.

v2: drop all atombios helper callings
v3: use bit operation
v4: correct inline comment, remove parity check statement
v5: squash in build fix

Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add pipe reassignment prevention code to dcn3

Add code to gracefuly handle any pipe reassignment
occuring on dcn3 hardware. This should only happen when new
surfaces are used for an update rather than old ones updated.

Fixes: 69fc1f4b976cea ("amd/drm/display: avoid dcn3 on flip opp change for slave pipes")
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use function pointer for gfxhub functions

gfxhub functions are now called from function pointers,
instead of from asic-specific functions.

Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: Prepare implementation to support reporting of CU usage

[Why]
Allow user to know number of compute units (CU) that are in use at any
given moment.

[How]
Read registers of SQ that give number of waves that are in flight
of various queues. Use this information to determine number of CU's
in use.

Signed-off-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: Clean up header file of symbols that are defined to be static

[Why]
Header file exports functions get_gpu_clock_counter(), get_cu_info() and
select_se_sh() that are defined to be static

Signed-off-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Use SKU instead of DID for FRU check v2

The VG20 DIDs 66a0, 66a1 and 66a4 are used for various SKUs that may or may
not have the FRU EEPROM on it. Parse the VBIOS to check for server SKU
variants (D131 or D134) until a more general solution can be determined.

v2: Remove string-based logic, correct the VBIOS string comment

Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/swsmu/smu12: fix force clock handling for mclk

The state array is in the reverse order compared to other asics
(high to low rather than low to high).

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1313
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove duplicate call to rn_vbios_smu_get_smu_version()

Commit 78fe9f63947a2b ("drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions")
added a call to rn_vbios_smu_get_smu_version() to set clk_mgr->smu_ver.
That field is initialized prior to the if-statement, already.

Fixes: 78fe9f63947a2b (drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions)
Signed-off-by: Dirk Gouders <dirk@gouders.net>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sung Lee <sung.lee@amd.com>
Cc: Yongqiang Sun <yongqiang.sun@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: add one sysfs file to support the feature to modify gfx clock on Raven/Raven2/Picasso APU.

This patch is to add one sysfs file -- "pp_od_clk_voltage" for
Raven/Raven2/Picasso APU, which is only used by dGPU like VEGA10.
This sysfs file supports the feature to modify gfx engine clock(Mhz units), it can
be used to configure the min value and the max value for gfx clock limited in the
safe range.

Command guide:
echo "s level clock" > pp_od_clk_voltage
s - adjust teh sclk level
level - 0 or 1, "0" represents the min value, "1" represents the max value
clock - the clock value(Mhz units), like 400, 800 or 1200, the value must be within the
                OD_RANGE limits.
Example:
$ cat pp_od_clk_voltage
OD_SCLK:
0:        200Mhz
1:       1400Mhz
OD_RANGE:
SCLK:     200MHz       1400MHz

$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0:        600Mhz
1:       1000Mhz
OD_RANGE:
SCLK:     200MHz       1400MHz

Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add new trace event for page table update

This patch adds a new trace event to track the PTE update
events. This specific event will provide information like:
- start and end of virtual memory mapping
- HW engine flags for the map
- physical address for mapping

This will be particularly useful for memory profiling tools
(like RMV) which are monitoring the page table update events.

V2: Added physical address lookup logic in trace point
V3: switch to use __dynamic_array
    added nptes int the TPprint arguments list
    added page size in the arg list
V4: Addressed Christian's review comments
    add start/end instead of seg
    use incr instead of page_sz to be accurate
V5: Addressed Christian's review comments:
    add pid and vm context information in the event
V6: Re-sequence the variables (put pid and ctx_id first)

Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix incorrect comment

It should be one copy-paste typo.

Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: restore proper ref count in amdgpu_display_crtc_set_config

A recent attempt to fix a ref count leak in
amdgpu_display_crtc_set_config() turned out to be doing too much and
"fixed" an intended decrease as if it were a leak. Undo that part to
restore the proper balance. This is the very nature of this function
to increase or decrease the power reference count depending on the
situation.

Consequences of this bug is that the power reference would
eventually get down to 0 while the display was still in use,
resulting in that display switching off unexpectedly.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: e008fa6fb415 ("drm/amdgpu: fix ref count leak in amdgpu_display_crtc_set_config")
Cc: stable@vger.kernel.org
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: make two symbols static

This addresses the following sparse warning:

drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:2740:6:
warning: symbol 'dce110_set_cursor_position' was not declared. Should it
be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:2785:6:
warning: symbol 'dce110_set_cursor_attribute' was not declared. Should
it be static?

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: make get_color_space_type() static

This addresses the following sparse warning:

drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_hw_sequencer.c:180:26:
warning: symbol 'get_color_space_type' was not declared. Should it be
static?

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

amd/drm/display: avoid dcn3 on flip opp change for slave pipes

At the moment on flip opp reassignment does not work in all cases
for non root pipes.
This change simply makes sure we prefer pipes not used previously
when splitting in dcn3.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Eric Bernstein <eric.bernstein@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: disable stream if pixel clock changed with link active

[Why]
Vbios uses preferred timing to turn on edp but OS could use other
timing.  If change pixel clock when link active, there is unexpected
garbage on monitor.

[How]
Once pixel clock changed, the driver needs to disable stream.

Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.35

[Header Changes]
   - Definition for retaining ABM settings during disable
   - Addition of some new AUX interface definitions
   - Addition of some outbox definitions

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Revert check for flip pending before locking pipes

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add debug param to force dio disable

[WHY]
At the moment, some tests are failing because cur_link_settings is
invalid. As a workaround, add an option to force dio disable.

Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Calc DLG from dummy p-state if full p-state unsupported

[Why]
Currently, when full p-state changes are not supported, DLG parameters
are calculated for no p-state support at all. However, we are required
to always support dummy p-state changes, so we should instead calculate
DLG based on dummy p-state latency when full p-state is unsupported.
This behaviour already exists for DCN2.

[How]
 - move DLG calculation inside WM calculation
 - if p-state unsupported, do not recalculate for set A, instead copy from
set C, and perform DLG calculation with dummy p-state latency

Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: disable stream if pixel clock changed with link active

[Why]
Vbios uses preferred timing to turn on edp but OS could use other
timing. If change pixel clock when link active, there is unexpected
garbage on monitor.

[How]
Once pixel clock changed, the driver needs to disable stream.

Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Ensure all debug bits are passed to fw

[Why]
Some debug bits are not being copied from driver to fw.

[How]
Copy debug bits properly.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add dp_set_dsc_pps_info_packet to virtual stream encoder

Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Update NV1x SR latency values

[Why]
HW team measurement requires updating values

[How]
Update bounding box values

Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: fix screen flicker seen on Navi14 with 2*4K monitors

Revert the guilty change introduced by the commit below:
drm/amd/pm: postpone SOCCLK/UCLK enablement after DAL initialization(V2)

Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix a warning in amdgpu_ras.c (v2)

drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c: In function ‘amdgpu_ras_fs_init’:
drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:1284:2: warning: ignoring return value of ‘sysfs_create_group’, declared with attribute warn_unused_result [-Wunused-result]
 1284 |  sysfs_create_group(&adev->dev->kobj, &group);
      |  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

v2: just print an error for sysfs group creation failure

Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: clean up ras sysfs creation (v2)

Merge ras sysfs creation together by calling sysfs_create_group
once, as sysfs_update_group may not work properly as expected.

v2: improve commit message

Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: stop data_exchange work thread before reset

In FLR routine, init_data_exchange is called at reset_sriov
while fini_data_exchange is not. This will duplicating work
thread.

So call fini_data_exchange before reset for SRIOV

Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Signed-off-by: Bokun Zhang <Bokun.Zhang@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Implement new guest side VF2PF message transaction (v2)

- Refactor the driver code to use amdgpu_virt_read_pf2vf_data
  and amdgpu_virt_write_vf2pf_data instead of writing all code in
  one function (which is the old amdgpu_virt_init_data_exchange)

- Adding a new transaction method for VF2PF message between host
  and guest driver. Guest side will periodically update VF2PF
  message in the framebuffer.

  In the new header, we include guest ucode information, guest
  framebuffer usage, and engine usage

- Clean up the old macros since they will cause compile error if
  the new transaction method is used

v2: squash in build fix

Signed-off-by: Bokun Zhang <Bokun.Zhang@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Update VF2PF interface

- Update guest side VF2PF interface header file

Signed-off-by: Bokun Zhang <Bokun.Zhang@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/include: add PP_FEATURE_MASK comments (v3)

Documents PP_FEATURE_MASK enum.
Provides instructions on how to use ppfeaturemasks.

v2: improve enum definitions and add kernel command line parameters to
    ppfeaturemask instructions
v3: fix alignment issues

Signed-off-by: Ryan Taylor <ryan.taylor@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>