drm/panfrost: Tighten polling for soft reset and power on

In many cases, soft reset takes more than 1 microsecond, but definitely
less than 10; moreover in the poweron flow, tilers, shaders and l2 will
become ready (each) in less than 10 microseconds as well.

Even in the cases (at least on my platforms, rarely) in which those take
more than 10 microseconds, it's very unlikely to see both soft reset and
poweron to take more than 70 microseconds.

Shorten the polling delay to 10 microseconds to consistently reduce the
runtime resume time of the GPU.

As an indicative example, measurements taken on a MediaTek MT8195 SoC

Average runtime resume time in nanoseconds before this commit:
GDM, user selection up/down:            88435ns
GDM, Text Entry (typing user/password): 91489ns
GNOME Desktop, idling, GKRELLM running: 73200ns

After this commit:

GDM: user selection up/down:            26690ns
GDM: Text Entry (typing user/password): 27917ns
GNOME Desktop, idling, GKRELLM running: 25304ns

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231109102543.42971-3-angelogioacchino.delregno@collabora.com

drm/panfrost: Perform hard reset to recover GPU if soft reset fails

Even though soft reset should ideally never fail, during development of
some power management features I managed to get some bits wrong: this
resulted in GPU soft reset failures, where the GPU was never able to
recover, not even after suspend/resume cycles, meaning that the only
way to get functionality back was to reboot the machine.

Perform a hard reset after a soft reset failure to be able to recover
the GPU during runtime (so, without any machine reboot).

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231109102543.42971-2-angelogioacchino.delregno@collabora.com

drm/panfrost: Really power off GPU cores in panfrost_gpu_power_off()

The layout of the registers {TILER,SHADER,L2}_PWROFF_LO, used to request
powering off cores, is the same as the {TILER,SHADER,L2}_PWRON_LO ones:
this means that in order to request poweroff of cores, we are supposed
to write a bitmask of cores that should be powered off!
This means that the panfrost_gpu_power_off() function has always been
doing nothing.

Fix powering off the GPU by writing a bitmask of the cores to poweroff
to the relevant PWROFF_LO registers and then check that the transition
(from ON to OFF) has finished by polling the relevant PWRTRANS_LO
registers.

While at it, in order to avoid code duplication, move the core mask
logic from panfrost_gpu_power_on() to a new panfrost_get_core_mask()
function, used in both poweron and poweroff.

Fixes: f3ba91228e8e ("drm/panfrost: Add initial panfrost driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102141507.73481-1-angelogioacchino.delregno@collabora.com

drm/sched: implement dynamic job-flow control

Currently, job flow control is implemented simply by limiting the number
of jobs in flight. Therefore, a scheduler is initialized with a credit
limit that corresponds to the number of jobs which can be sent to the
hardware.

This implies that for each job, drivers need to account for the maximum
job size possible in order to not overflow the ring buffer.

However, there are drivers, such as Nouveau, where the job size has a
rather large range. For such drivers it can easily happen that job
submissions not even filling the ring by 1% can block subsequent
submissions, which, in the worst case, can lead to the ring run dry.

In order to overcome this issue, allow for tracking the actual job size
instead of the number of jobs. Therefore, add a field to track a job's
credit count, which represents the number of credits a job contributes
to the scheduler's credit limit.

Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110001638.71750-1-dakr@redhat.com

drm/sched: Define pr_fmt() for DRM using pr_*()

Define pr_fmt() as "[drm] " for DRM code using pr_*() facilities, especially
when no devices are available. This makes it easier to browse kernel logs.

Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>
Acked-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110002659.113208-2-ltuikov89@gmail.com

drm/panel-edp: drm/panel-edp: Add several generic edp panels

Add a few generic edp panels used by mt8186 chromebooks.

Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107204611.3082200-4-hsinyi@chromium.org

drm/panel-edp: drm/panel-edp: Fix AUO B116XTN02 name

Rename AUO 0x235c B116XTN02 to B116XTN02.3 according to decoding edid.

Fixes: 3db2420422a5 ("drm/panel-edp: Add AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49 V8.0")
Cc: stable@vger.kernel.org
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107204611.3082200-3-hsinyi@chromium.org

drm/panel-edp: drm/panel-edp: Fix AUO B116XAK01 name and timing

Rename AUO 0x405c B116XAK01 to B116XAK01.0 and adjust the timing of
auo_b116xak01: T3=200, T12=500, T7_max = 50 according to decoding edid
and datasheet.

Fixes: da458286a5e2 ("drm/panel: Add support for AUO B116XAK01 panel")
Cc: stable@vger.kernel.org
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107204611.3082200-2-hsinyi@chromium.org

drm/sched: Qualify drm_sched_wakeup() by drm_sched_entity_is_ready()

Don't "wake up" the GPU scheduler unless the entity is ready, as well as we
can queue to the scheduler, i.e. there is no point in waking up the scheduler
for the entity unless the entity is ready.

Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>
Fixes: bc8d6a9df99038 ("drm/sched: Don't disturb the entity when in RR-mode scheduling")
Reviewed-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110000123.72565-2-ltuikov89@gmail.com

drm/eld: add helpers to modify the SADs of an ELD

Occasionally it's necessary for drivers to modify the SADs of an ELD,
but it's not so cool to have drivers poke at the ELD buffer directly.

Using the helpers to translate between 3-byte SAD and struct cea_sad,
add ELD helpers to get/set the SADs from/to an ELD.

v2: s/i/sad_index/ (Mitul)

Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8e9a05f2b1e0dd184132d636e1e778e8917ec25d.1698747331.git.jani.nikula@intel.com

drm/edid: add helpers to get/set struct cea_sad from/to 3-byte sad

Add helpers to pack/unpack SADs. Both ways and non-static, as follow-up
work needs them.

v2: Add include to get the declarations

Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/21d657ca854ce26423b461c0bb71e7a0727ba437.1698747331.git.jani.nikula@intel.com

drm/edid: use a temp variable for sads to drop one level of dereferences

Use a temporary variable struct cea_sad *, instead of using struct
cea_sad ** directly with the double dereferences. It's arguably easier
on the eyes, and drops a set of parenthesis too.

Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b6e2f295ae5491c2bb0f528508f0f5fca921dc77.1698747331.git.jani.nikula@intel.com

drm/edid: include drm_eld.h only where required

Reduce the dependencies on drm_eld.h. Some files might be able to drop
the dependency on drm_edid.h too with the direct inclusion of drm_eld.h.

Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9f5963ce900d747f3279312c0cd1da599fd83f94.1698747331.git.jani.nikula@intel.com

drm/eld: replace uint8_t with u8

Unify on kernel types.

Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e048fc4c8a3ebec638ce27b0b8b969a3d2fa8bc.1698747331.git.jani.nikula@intel.com

drm/edid: split out drm_eld.h from drm_edid.h

The drm_edid.[ch] files are starting to be a bit crowded, and with plans
to add more ELD related functionality, it's perhaps cleanest to split
the ELD code out to a header of its own.

Include drm_eld.h from drm_edid.h for starters, and leave it to
follow-up work to only include drm_eld.h where needed.

Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0c6d631fa1058036d72dd25d1cabc90a7c52490e.1698747331.git.jani.nikula@intel.com

MAINTAINERS: Add Maira to V3D maintainers

I've been contributing to V3D with improvements, reviews, testing and
debugging. Therefore, add myself as a co-maintainer of the V3D driver.

Signed-off-by: Maíra Canal <mcanal@igalia.com>
Acked-by: Melissa Wen <mwen@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231106134201.725805-1-mcanal@igalia.com

drm/todo: Add entry to clean up former seltests suites

Most of those suites are undocumented and aren't really clear about what
they are testing. Let's add a TODO entry as a future task to get started
into KUnit and DRM.

Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://lore.kernel.org/r/20231025132428.723672-2-mripard@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/tests: Remove slow tests

Both the drm_buddy and drm_mm tests have been converted from selftest to
kunit recently.

However, a significant portion of them are trying to exert some part of
their API over a huge number of iterations and with random variations of
their parameters.  They are thus more a way to discover new bugs than
actual unit tests.

This is fine in itself but leads to very slow runtime (up to 25s for
some drm_test_mm_reserve and drm_test_mm_insert on a Ryzen 7950x while
running the tests in qemu) which make them a poor fit for kunit.

Let's remove those tests from the drm_mm and drm_buddy test suites for
now, and if it's ever needed we can always create proper unit tests for
them later on.

This made the entire DRM tests execution time (as of v6.6-rc1) come from
65s to less than .5s on a Ryzen 7950x system when running under qemu,
and from 9 minutes to about 4s on a RaspberryPi4.

Acked-by: Daniel Vetter <daniel@ffwll.ch>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://lore.kernel.org/r/20231025132428.723672-1-mripard@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>

accel/ivpu: Use GEM shmem helper for all buffers

Use struct drm_gem_shmem_object as a base for struct ivpu_bo.
This cuts by 50% the buffer management code.

Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031073156.1301669-5-stanislaw.gruszka@linux.intel.com

accel/ivpu: Remove support for uncached buffers

Usages of DRM_IVPU_BO_UNCACHED should be replaced by DRM_IVPU_BO_WC.
There is no functional benefit from DRM_IVPU_BO_UNCACHED if these
buffers are never mapped to host VM.

This allows to cut the buffer handling code in the kernel driver
by half.

Usage of DRM_IVPU_BO_UNCACHED buffers was removed from user-space
driver and will not be part of first UMD release.

Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031073156.1301669-4-stanislaw.gruszka@linux.intel.com

accel/ivpu: Fix locking in ivpu_bo_remove_all_bos_from_context()

ivpu_bo_remove_all_bos_from_context() could race with ivpu_bo_free()
when prime buffer was closed after vpu device was closed.

Move the bo_list from context to vdev and use a dedicated lock to
sync it. This list is not modified when BO is added/removed from
a context.

Also rename ivpu_bo_free_vpu_addr() to ivpu_bo_unbind() because this
function does more then just free vpu_addr.

Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031073156.1301669-3-stanislaw.gruszka@linux.intel.com

accel/ivpu: Allocate vpu_addr in gem->open() callback

Use gem->open() callback to simplify the code and prepare for gem_shmem
conversion. It is called during handle creation for a gem object,
during prime import and in BO_CREATE ioctl. Hence can be used for vpu_addr
allocation. On the way remove unused bo->user_ptr field.

Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031073156.1301669-2-stanislaw.gruszka@linux.intel.com

MAINTAINERS: Drop Emma Anholt from all M lines.

I am not active in the Linux kernel and don't want to see patches.

Signed-off-by: Emma Anholt <emma@anholt.net>
Acked-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031181648.48675-1-emma@anholt.net

drm/sched: Don't disturb the entity when in RR-mode scheduling

Don't call drm_sched_select_entity() in drm_sched_run_job_queue().  In fact,
rename __drm_sched_run_job_queue() to just drm_sched_run_job_queue(), and let
it do just that, schedule the work item for execution.

The problem is that drm_sched_run_job_queue() calls drm_sched_select_entity()
to determine if the scheduler has an entity ready in one of its run-queues,
and in the case of the Round-Robin (RR) scheduling, the function
drm_sched_rq_select_entity_rr() does just that, selects the _next_ entity
which is ready, sets up the run-queue and completion and returns that
entity. The FIFO scheduling algorithm is unaffected.

Now, since drm_sched_run_job_work() also calls drm_sched_select_entity(), then
in the case of RR scheduling, that would result in drm_sched_select_entity()
having been called twice, which may result in skipping a ready entity if more
than one entity is ready. This commit fixes this by eliminating the call to
drm_sched_select_entity() from drm_sched_run_job_queue(), and leaves it only
in drm_sched_run_job_work().

v2: Rebased on top of Tvrtko's renames series of patches. (Luben)
    Add fixes-tag. (Tvrtko)

Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>
Fixes: f7fe64ad0f22ff ("drm/sched: Split free_job into own work item")
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107041020.10035-2-ltuikov89@gmail.com

accel/ivpu: Fix compilation with CONFIG_PM=n

Use pm_runtime_status_suspended() instead of dev->power.runtime_status
field that is not available without PM.

Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/all/20231106130827.1600948-1-jacek.lawrynowicz@linux.intel.com

drm/panel: nt35510: fix typo

Replace 'HFP' with 'HBP'.

Fixes: 899f24ed8d3a ("drm/panel: Add driver for Novatek NT35510-based panels")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231023090613.1694133-1-dario.binacchi@amarulasolutions.com

drm/v3d: Expose the total GPU usage stats on sysfs

The previous patch exposed the accumulated amount of active time per
client for each V3D queue. But this doesn't provide a global notion of
the GPU usage.

Therefore, provide the accumulated amount of active time for each V3D
queue (BIN, RENDER, CSD, TFU and CACHE_CLEAN), considering all the jobs
submitted to the queue, independent of the client.

This data is exposed through the sysfs interface, so that if the
interface is queried at two different points of time the usage percentage
of each of the queues can be calculated.

Co-developed-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Signed-off-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Acked-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230905213416.1290219-3-mcanal@igalia.com

drm/v3d: Implement show_fdinfo() callback for GPU usage stats

This patch exposes the accumulated amount of active time per client
through the fdinfo infrastructure. The amount of active time is exposed
for each V3D queue: BIN, RENDER, CSD, TFU and CACHE_CLEAN.

In order to calculate the amount of active time per client, a CPU clock
is used through the function local_clock(). The point where the jobs has
started is marked and is finally compared with the time that the job had
finished.

Moreover, the number of jobs submitted to each queue is also exposed on
fdinfo through the identifier "v3d-jobs-<queue>".

Co-developed-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Signed-off-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Acked-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230905213416.1290219-3-mcanal@igalia.com

drm: Do not round to megabytes for greater than 1MiB sizes in fdinfo stats

It is better not to lose precision and not revert to 1 MiB size
granularity for every size greater than 1 MiB.

Sizes in KiB should not be so troublesome to read (and in fact machine
parsing is I expect the norm here), they align with other api like
/proc/meminfo, and they allow writing tests for the interface without
having to embed drm.ko implementation knowledge into them. (Like knowing
that minimum buffer size one can use for successful verification has to be
1MiB aligned, and on top account for any pre-existing memory utilisation
outside of driver's control.)

But probably even more importantly I think that it is just better to show
the accurate sizes and not arbitrary lose precision for a little bit of a
stretched use case of eyeballing fdinfo text directly.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Adrián Larumbe <adrian.larumbe@collabora.com>
Cc: steven.price@arm.com
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20230927133843.247957-2-tvrtko.ursulin@linux.intel.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/sched: Drop suffix from drm_sched_wakeup_if_can_queue

Because a) helper is exported to other parts of the scheduler and
b) there isn't a plain drm_sched_wakeup to begin with, I think we can
drop the suffix and by doing so separate the intimiate knowledge
between the scheduler components a bit better.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Luben Tuikov <ltuikov89@gmail.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102105538.391648-6-tvrtko.ursulin@linux.intel.com
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

drm/sched: Rename drm_sched_run_job_queue_if_ready and clarify kerneldoc

"If ready" is not immediately clear what it means - is the scheduler
ready or something else? Drop the suffix, clarify kerneldoc, and employ
the same naming scheme as in drm_sched_run_free_queue:

 - drm_sched_run_job_queue   - enqueues if there is something to enqueue
                               *and* scheduler is ready (can queue)
 - __drm_sched_run_job_queue - low-level helper to simply queue the job

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Luben Tuikov <ltuikov89@gmail.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102105538.391648-5-tvrtko.ursulin@linux.intel.com
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

drm/sched: Rename drm_sched_free_job_queue to be more descriptive

The current name makes it sound like helper will free a queue, while what
it does is it enqueues the free job worker.

Rename it to drm_sched_run_free_queue to align with existing
drm_sched_run_job_queue.

Despite that creating an illusion there are two queues, while in reality
there is only one, at least it creates a consistent naming for the two
enqueuing helpers.

At the same time simplify the "if done" helper by dropping the suffix and
adding a double underscore prefix to the one which just enqueues.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Luben Tuikov <ltuikov89@gmail.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102105538.391648-4-tvrtko.ursulin@linux.intel.com
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

drm/sched: Move free worker re-queuing out of the if block

Whether or not there are more jobs to clean up does not depend on the
existance of the current job, given both drm_sched_get_finished_job and
drm_sched_free_job_queue_if_done take and drop the job list lock.
Therefore it is confusing to make it read like there is a dependency.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Luben Tuikov <ltuikov89@gmail.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102105538.391648-3-tvrtko.ursulin@linux.intel.com
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

drm/sched: Rename drm_sched_get_cleanup_job to be more descriptive

"Get cleanup job" makes it sound like helper is returning a job which will
execute some cleanup, or something, while the kerneldoc itself accurately
says "fetch the next _finished_ job". So lets rename the helper to be self
documenting.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Luben Tuikov <ltuikov89@gmail.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231102105538.391648-2-tvrtko.ursulin@linux.intel.com
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

accel/qaic: Support for 0 resize slice execution in BO

Add support to partially execute a slice which is resized to zero.
Executing a zero size slice in a BO should mean that there is no DMA
transfers involved but you should still configure doorbell and semaphores.

For example consider a BO of size 18K and it is sliced into 3 6K slices
and user calls partial execute ioctl with resize as 10K.
slice 0 - size is 6k and offset is 0, so resize of 10K will not cut short
          this slice hence we send the entire slice for execution.
slice 1 - size is 6k and offset is 6k, so resize of 10K will cut short this
          slice and only the first 4k should be DMA along with configuring
          doorbell and semaphores.
slice 2 - size is 6k and offset is 12k, so resize of 10k will cut short
          this slice and no DMA transfer would be involved but we should
          would configure doorbell and semaphores.

This change begs to change the behavior of 0 resize. Currently, 0 resize
partial execute ioctl behaves exactly like execute ioctl i.e. no resize.
After this patch all the slice in BO should behave exactly like slice 2 in
above example.

Refactor copy_partial_exec_reqs() to make it more readable and less
complex.

Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231027164330.11978-1-quic_jhugo@quicinc.com

accel/qaic: Quiet array bounds check on DMA abort message

Current wrapper is right-sized to the message being transferred;
however, this is smaller than the structure defining message wrappers
since the trailing element is a union of message/transfer headers of
various sizes (8 and 32 bytes on 32-bit system where issue was
reported). Using the smaller header with a small message
(wire_trans_dma_xfer is 24 bytes including header) ends up being smaller
than a wrapper with the larger header. There are no accesses outside of
the defined size, however they are possible if the larger union member
is referenced.

Abort messages are outside of hot-path and changing the wrapper struct
would require a larger rewrite, so having the memory allocated to the
message be 8 bytes too big is acceptable.

Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310182253.bcb9JcyJ-lkp@intel.com/
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231027180810.4873-1-quic_jhugo@quicinc.com

drm/v3d: add brcm,2712-v3d as a compatible V3D device

This is required to get the V3D module to load with Raspberry Pi 5.

Signed-off-by: Iago Toral Quiroga <itoral@igalia.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031073859.25298-5-itoral@igalia.com

dt-bindings: gpu: v3d: Add BCM2712's compatible

BCM2712, Raspberry Pi 5's SoC, contains a V3D core. So add its specific
compatible to the bindings.

Signed-off-by: Iago Toral Quiroga <itoral@igalia.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031073859.25298-4-itoral@igalia.com

drm/v3d: fix up register addresses for V3D 7.x

This patch updates a number of register addresses that have
been changed in Raspberry Pi 5 (V3D 7.1) and updates the
code to use the corresponding registers and addresses based
on the actual V3D version.

Signed-off-by: Iago Toral Quiroga <itoral@igalia.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031073859.25298-3-itoral@igalia.com

drm/v3d: update UAPI to match user-space for V3D 7.x

V3D 7.x takes a new parameter to configure TFU jobs that needs
to be provided by user space.

Signed-off-by: Iago Toral Quiroga <itoral@igalia.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031073859.25298-2-itoral@igalia.com

fbdev/simplefb: Add support for generic power-domains

The simple-framebuffer device tree bindings document the power-domains
property, so make sure that simplefb supports it. This ensures that the
power domains remain enabled as long as simplefb is active.

v2: - remove unnecessary call to simplefb_detach_genpds() since that's
      already done automatically by devres
    - fix crash if power-domains property is missing in DT

Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231101172017.3872242-3-thierry.reding@gmail.com

fbdev/simplefb: Support memory-region property

The simple-framebuffer bindings specify that the "memory-region"
property can be used as an alternative to the "reg" property to define
the framebuffer memory used by the display hardware. Implement support
for this in the simplefb driver.

Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231101172017.3872242-2-thierry.reding@gmail.com

drm/sched: Add a helper to queue TDR immediately

Add a helper whereby a driver can invoke TDR immediately.

v2:
 - Drop timeout args, rename function, use mod delayed work (Luben)
v3:
 - s/XE/Xe (Luben)
 - present tense in commit message (Luben)
 - Adjust comment for drm_sched_tdr_queue_imm (Luben)
v4:
 - Adjust commit message (Luben)

Cc: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Link: https://lore.kernel.org/r/20231031032439.1558703-6-matthew.brost@intel.com
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

drm/sched: Add drm_sched_start_timeout_unlocked helper

Also add a lockdep assert to drm_sched_start_timeout.

Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Link: https://lore.kernel.org/r/20231031032439.1558703-5-matthew.brost@intel.com
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

drm/sched: Split free_job into own work item

Rather than call free_job and run_job in same work item have a dedicated
work item for each. This aligns with the design and intended use of work
queues.

v2:
   - Test for DMA_FENCE_FLAG_TIMESTAMP_BIT before setting
     timestamp in free_job() work item (Danilo)
v3:
  - Drop forward dec of drm_sched_select_entity (Boris)
  - Return in drm_sched_run_job_work if entity NULL (Boris)
v4:
  - Replace dequeue with peek and invert logic (Luben)
  - Wrap to 100 lines (Luben)
  - Update comments for *_queue / *_queue_if_ready functions (Luben)
v5:
  - Drop peek argument, blindly reinit idle (Luben)
  - s/drm_sched_free_job_queue_if_ready/drm_sched_free_job_queue_if_done (Luben)
  - Update work_run_job & work_free_job kernel doc (Luben)
v6:
  - Do not move drm_sched_select_entity in file (Luben)

Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20231031032439.1558703-4-matthew.brost@intel.com
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

drm/sched: Convert drm scheduler to use a work queue rather than kthread

In Xe, the new Intel GPU driver, a choice has made to have a 1 to 1
mapping between a drm_gpu_scheduler and drm_sched_entity. At first this
seems a bit odd but let us explain the reasoning below.

1. In Xe the submission order from multiple drm_sched_entity is not
guaranteed to be the same completion even if targeting the same hardware
engine. This is because in Xe we have a firmware scheduler, the GuC,
which allowed to reorder, timeslice, and preempt submissions. If a using
shared drm_gpu_scheduler across multiple drm_sched_entity, the TDR falls
apart as the TDR expects submission order == completion order. Using a
dedicated drm_gpu_scheduler per drm_sched_entity solve this problem.

2. In Xe submissions are done via programming a ring buffer (circular
buffer), a drm_gpu_scheduler provides a limit on number of jobs, if the
limit of number jobs is set to RING_SIZE / MAX_SIZE_PER_JOB we get flow
control on the ring for free.

A problem with this design is currently a drm_gpu_scheduler uses a
kthread for submission / job cleanup. This doesn't scale if a large
number of drm_gpu_scheduler are used. To work around the scaling issue,
use a worker rather than kthread for submission / job cleanup.

v2:
  - (Rob Clark) Fix msm build
  - Pass in run work queue
v3:
  - (Boris) don't have loop in worker
v4:
  - (Tvrtko) break out submit ready, stop, start helpers into own patch
v5:
  - (Boris) default to ordered work queue
v6:
  - (Luben / checkpatch) fix alignment in msm_ringbuffer.c
  - (Luben) s/drm_sched_submit_queue/drm_sched_wqueue_enqueue
  - (Luben) Update comment for drm_sched_wqueue_enqueue
  - (Luben) Positive check for submit_wq in drm_sched_init
  - (Luben) s/alloc_submit_wq/own_submit_wq
v7:
  - (Luben) s/drm_sched_wqueue_enqueue/drm_sched_run_job_queue
v8:
  - (Luben) Adjust var names / comments

Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Link: https://lore.kernel.org/r/20231031032439.1558703-3-matthew.brost@intel.com
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

drm/sched: Add drm_sched_wqueue_* helpers

Add scheduler wqueue ready, stop, and start helpers to hide the
implementation details of the scheduler from the drivers.

v2:
  - s/sched_wqueue/sched_wqueue (Luben)
  - Remove the extra white line after the return-statement (Luben)
  - update drm_sched_wqueue_ready comment (Luben)

Cc: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Link: https://lore.kernel.org/r/20231031032439.1558703-2-matthew.brost@intel.com
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

dma-buf: add dma_fence_timestamp helper

When a fence signals there is a very small race window where the timestamp
isn't updated yet. sync_file solves this by busy waiting for the
timestamp to appear, but on other ocassions didn't handled this
correctly.

Provide a dma_fence_timestamp() helper function for this and use it in
all appropriate cases.

Another alternative would be to grab the spinlock when that happens.

v2 by teddy: add a wait parameter to wait for the timestamp to show up, in case
   the accurate timestamp is needed and/or the timestamp is not based on
   ktime (e.g. hw timestamp)
v3 chk: drop the parameter again for unified handling

Signed-off-by: Yunxiang Li <Yunxiang.Li@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 1774baa64f93 ("drm/scheduler: Change scheduled fence track v2")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20230929104725.2358-1-christian.koenig@amd.com

accel/ivpu: Rename VPU to NPU in product strings

VPU was rebranded as NPU (Neural Processing Unit) so user facing
strings have to be updated but the code remains as is and the module
is still called intel_vpu.ko.

Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-9-stanislaw.gruszka@linux.intel.com

accel/ivpu: Simplify MMU SYNC command

CMD_SYNC does not need any args as we poll for completion anyway.

Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-8-stanislaw.gruszka@linux.intel.com

accel/ivpu: Make DMA allocations for MMU600 write combined

Previously using dma_alloc_wc() API we created cache coherent
(mapped as write-back) mappings.

Because we disable MMU600 snooping it was required to do costly
page walk and cache flushes after each page table modification.

With write-combined buffers it's possible to do a single write memory
barrier to flush write-combined buffer to memory which simplifies the
driver and significantly reduce time of map/unmap operations.

Mapping time of 255 MB is reduced from 2.5 ms to 500 us.

Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-7-stanislaw.gruszka@linux.intel.com

accel/ivpu: Print CMDQ errors after consumer timeout

Add checking of error reason bits in IVPU_MMU_CMDQ_CONS
register when waiting for consumer timeout occurred.

Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-6-stanislaw.gruszka@linux.intel.com

accel/ivpu: Abort pending rx ipc on reset

Waking up process, which wait for particular condition, will go to
sleep again on wake_up() if the condition is not met. Add abort flag
to wake up IPC receivers, which will finish with -ECANCELED error.

This is only needed for reset, run time power management prevent to
suspend VPU when there is pending IPC processing or pending job.

Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-5-stanislaw.gruszka@linux.intel.com

accel/ivpu: Stop job_done_thread on suspend

Stop job_done thread when going to suspend. Use kthread_park() instead
of kthread_stop() to avoid memory allocation and potential failure
on resume.

Use separate function as thread wake up condition. Use spin lock to assure
rx_msg_list is properly protected against concurrent access. This avoid
race condition when the rx_msg_list list is modified and read in
ivpu_ipc_recive() at the same time.

Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-4-stanislaw.gruszka@linux.intel.com

accel/ivpu: Assure device is off if power up sequence fail

We should not leave device half enabled if there is failure somewhere
it power up sequence. Fix device init and resume paths.

Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-3-stanislaw.gruszka@linux.intel.com

accel/ivpu/40xx: Allow to change profiling frequency

Profiling freq is a debug firmware feature. It switches default clock
to higher resolution for fine-grained and more accurate firmware task
profiling. We already configure it during boot up of VPU4.

Add debugfs knob and helpers per HW generation that allow to change it.
For vpu37xx the implementation is empty as profiling frequency can only
be changed on VPU4 or newer.

Signed-off-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028155936.1183342-2-stanislaw.gruszka@linux.intel.com

Revert "drm/omapdrm: Annotate dma-fence critical section in commit path"

This reverts commit 250aa22920cd5d956a5d3e9c6a43d671c2bae217.

The DMA-fence annotations cause a lockdep warning (see below). As per
https://patchwork.freedesktop.org/patch/462170/ it sounds like the
annotations don't work correctly.

======================================================
WARNING: possible circular locking dependency detected
6.5.0-rc2+ #2 Not tainted
------------------------------------------------------
kmstest/219 is trying to acquire lock:
c4705838 (&hdmi->lock){+.+.}-{3:3}, at: hdmi5_bridge_mode_set+0x1c/0x50

but task is already holding lock:
c11e1128 (dma_fence_map){++++}-{0:0}, at: omap_atomic_commit_tail+0x14/0xbc

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (dma_fence_map){++++}-{0:0}:
       __dma_fence_might_wait+0x48/0xb4
       dma_resv_lockdep+0x1b8/0x2bc
       do_one_initcall+0x68/0x3b0
       kernel_init_freeable+0x260/0x34c
       kernel_init+0x14/0x140
       ret_from_fork+0x14/0x28

-> #1 (fs_reclaim){+.+.}-{0:0}:
       fs_reclaim_acquire+0x70/0xa8
       __kmem_cache_alloc_node+0x3c/0x368
       kmalloc_trace+0x28/0x58
       _drm_do_get_edid+0x7c/0x35c
       hdmi5_bridge_get_edid+0xc8/0x1ac
       drm_bridge_connector_get_modes+0x64/0xc0
       drm_helper_probe_single_connector_modes+0x170/0x528
       drm_client_modeset_probe+0x208/0x1334
       __drm_fb_helper_initial_config_and_unlock+0x30/0x548
       omap_fbdev_client_hotplug+0x3c/0x6c
       drm_client_register+0x58/0x94
       pdev_probe+0x544/0x6b0
       platform_probe+0x58/0xbc
       really_probe+0xd8/0x3fc
       __driver_probe_device+0x94/0x1f4
       driver_probe_device+0x2c/0xc4
       __device_attach_driver+0xa4/0x11c
       bus_for_each_drv+0x84/0xdc
       __device_attach+0xac/0x20c
       bus_probe_device+0x8c/0x90
       device_add+0x588/0x7e0
       platform_device_add+0x110/0x24c
       platform_device_register_full+0x108/0x15c
       dss_bind+0x90/0xc0
       try_to_bring_up_aggregate_device+0x1e0/0x2c8
       __component_add+0xa4/0x174
       hdmi5_probe+0x1c8/0x270
       platform_probe+0x58/0xbc
       really_probe+0xd8/0x3fc
       __driver_probe_device+0x94/0x1f4
       driver_probe_device+0x2c/0xc4
       __device_attach_driver+0xa4/0x11c
       bus_for_each_drv+0x84/0xdc
       __device_attach+0xac/0x20c
       bus_probe_device+0x8c/0x90
       deferred_probe_work_func+0x8c/0xd8
       process_one_work+0x2ac/0x6e4
       worker_thread+0x30/0x4ec
       kthread+0x100/0x124
       ret_from_fork+0x14/0x28

-> #0 (&hdmi->lock){+.+.}-{3:3}:
       __lock_acquire+0x145c/0x29cc
       lock_acquire.part.0+0xb4/0x258
       __mutex_lock+0x90/0x950
       mutex_lock_nested+0x1c/0x24
       hdmi5_bridge_mode_set+0x1c/0x50
       drm_bridge_chain_mode_set+0x48/0x5c
       crtc_set_mode+0x188/0x1d0
       omap_atomic_commit_tail+0x2c/0xbc
       commit_tail+0x9c/0x188
       drm_atomic_helper_commit+0x158/0x18c
       drm_atomic_commit+0xa4/0xe8
       drm_mode_atomic_ioctl+0x9a4/0xc38
       drm_ioctl+0x210/0x4a8
       sys_ioctl+0x138/0xf00
       ret_fast_syscall+0x0/0x1c

other info that might help us debug this:

Chain exists of:
  &hdmi->lock --> fs_reclaim --> dma_fence_map

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  rlock(dma_fence_map);
                               lock(fs_reclaim);
                               lock(dma_fence_map);
  lock(&hdmi->lock);

 *** DEADLOCK ***

3 locks held by kmstest/219:
 #0: f1011de4 (crtc_ww_class_acquire){+.+.}-{0:0}, at: drm_mode_atomic_ioctl+0xf0/0xc38
 #1: c47059c8 (crtc_ww_class_mutex){+.+.}-{3:3}, at: modeset_lock+0xf8/0x230
 #2: c11e1128 (dma_fence_map){++++}-{0:0}, at: omap_atomic_commit_tail+0x14/0xbc

stack backtrace:
CPU: 1 PID: 219 Comm: kmstest Not tainted 6.5.0-rc2+ #2
Hardware name: Generic DRA74X (Flattened Device Tree)
 unwind_backtrace from show_stack+0x10/0x14
 show_stack from dump_stack_lvl+0x58/0x70
 dump_stack_lvl from check_noncircular+0x164/0x198
 check_noncircular from __lock_acquire+0x145c/0x29cc
 __lock_acquire from lock_acquire.part.0+0xb4/0x258
 lock_acquire.part.0 from __mutex_lock+0x90/0x950
 __mutex_lock from mutex_lock_nested+0x1c/0x24
 mutex_lock_nested from hdmi5_bridge_mode_set+0x1c/0x50
 hdmi5_bridge_mode_set from drm_bridge_chain_mode_set+0x48/0x5c
 drm_bridge_chain_mode_set from crtc_set_mode+0x188/0x1d0
 crtc_set_mode from omap_atomic_commit_tail+0x2c/0xbc
 omap_atomic_commit_tail from commit_tail+0x9c/0x188
 commit_tail from drm_atomic_helper_commit+0x158/0x18c
 drm_atomic_helper_commit from drm_atomic_commit+0xa4/0xe8
 drm_atomic_commit from drm_mode_atomic_ioctl+0x9a4/0xc38
 drm_mode_atomic_ioctl from drm_ioctl+0x210/0x4a8
 drm_ioctl from sys_ioctl+0x138/0xf00
 sys_ioctl from ret_fast_syscall+0x0/0x1c
Exception stack(0xf1011fa8 to 0xf1011ff0)
1fa0:                   00466d58 be9ab510 00000003 c03864bc be9ab510 be9ab4e0
1fc0: 00466d58 be9ab510 c03864bc 00000036 00466ef0 00466fc0 00467020 00466f20
1fe0: b6bc7ef4 be9ab4d0 b6bbbb00 b6cb2cc0

Fixes: 250aa22920cd ("drm/omapdrm: Annotate dma-fence critical section in commit path")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920-dma-fence-annotation-revert-v1-2-7ebf6f7f5bf6@ideasonboard.com

Revert "drm/tidss: Annotate dma-fence critical section in commit path"

This reverts commit 4d56a4f08391857ba93465de489707b66adad114.

The DMA-fence annotations cause a lockdep warning (see below). As per
https://patchwork.freedesktop.org/patch/462170/ it sounds like the
annotations don't work correctly.

======================================================
WARNING: possible circular locking dependency detected
6.6.0-rc2+ #1 Not tainted
------------------------------------------------------
kmstest/733 is trying to acquire lock:
ffff8000819377f0 (fs_reclaim){+.+.}-{0:0}, at: __kmem_cache_alloc_node+0x58/0x2d4

but task is already holding lock:
ffff800081a06aa0 (dma_fence_map){++++}-{0:0}, at: tidss_atomic_commit_tail+0x20/0xc0 [tidss]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (dma_fence_map){++++}-{0:0}:
       __dma_fence_might_wait+0x5c/0xd0
       dma_resv_lockdep+0x1a4/0x32c
       do_one_initcall+0x84/0x2fc
       kernel_init_freeable+0x28c/0x4c4
       kernel_init+0x24/0x1dc
       ret_from_fork+0x10/0x20

-> #1 (mmu_notifier_invalidate_range_start){+.+.}-{0:0}:
       fs_reclaim_acquire+0x70/0xe4
       __kmem_cache_alloc_node+0x58/0x2d4
       kmalloc_trace+0x38/0x78
       __kthread_create_worker+0x3c/0x150
       kthread_create_worker+0x64/0x8c
       workqueue_init+0x1e8/0x2f0
       kernel_init_freeable+0x11c/0x4c4
       kernel_init+0x24/0x1dc
       ret_from_fork+0x10/0x20

-> #0 (fs_reclaim){+.+.}-{0:0}:
       __lock_acquire+0x1370/0x20d8
       lock_acquire+0x1e8/0x308
       fs_reclaim_acquire+0xd0/0xe4
       __kmem_cache_alloc_node+0x58/0x2d4
       __kmalloc_node_track_caller+0x58/0xf0
       kmemdup+0x34/0x60
       regmap_bulk_write+0x64/0x2c0
       tc358768_bridge_pre_enable+0x8c/0x12d0 [tc358768]
       drm_atomic_bridge_call_pre_enable+0x68/0x80 [drm]
       drm_atomic_bridge_chain_pre_enable+0x50/0x158 [drm]
       drm_atomic_helper_commit_modeset_enables+0x164/0x264 [drm_kms_helper]
       tidss_atomic_commit_tail+0x58/0xc0 [tidss]
       commit_tail+0xa0/0x188 [drm_kms_helper]
       drm_atomic_helper_commit+0x1a8/0x1c0 [drm_kms_helper]
       drm_atomic_commit+0xa8/0xe0 [drm]
       drm_mode_atomic_ioctl+0x9ec/0xc80 [drm]
       drm_ioctl_kernel+0xc4/0x170 [drm]
       drm_ioctl+0x234/0x4b0 [drm]
       drm_compat_ioctl+0x110/0x12c [drm]
       __arm64_compat_sys_ioctl+0x128/0x150
       invoke_syscall+0x48/0x110
       el0_svc_common.constprop.0+0x40/0xe0
       do_el0_svc_compat+0x1c/0x38
       el0_svc_compat+0x48/0xb4
       el0t_32_sync_handler+0xb0/0x138
       el0t_32_sync+0x194/0x198

other info that might help us debug this:

Chain exists of:
  fs_reclaim --> mmu_notifier_invalidate_range_start --> dma_fence_map

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  rlock(dma_fence_map);
                               lock(mmu_notifier_invalidate_range_start);
                               lock(dma_fence_map);
  lock(fs_reclaim);

 *** DEADLOCK ***

3 locks held by kmstest/733:
 #0: ffff800082e5bba0 (crtc_ww_class_acquire){+.+.}-{0:0}, at: drm_mode_atomic_ioctl+0x118/0xc80 [drm]
 #1: ffff000004224c88 (crtc_ww_class_mutex){+.+.}-{3:3}, at: modeset_lock+0xdc/0x1a0 [drm]
 #2: ffff800081a06aa0 (dma_fence_map){++++}-{0:0}, at: tidss_atomic_commit_tail+0x20/0xc0 [tidss]

stack backtrace:
CPU: 0 PID: 733 Comm: kmstest Not tainted 6.6.0-rc2+ #1
Hardware name: Toradex Verdin AM62 on Verdin Development Board (DT)
Call trace:
 dump_backtrace+0x98/0x118
 show_stack+0x18/0x24
 dump_stack_lvl+0x60/0xac
 dump_stack+0x18/0x24
 print_circular_bug+0x288/0x368
 check_noncircular+0x168/0x17c
 __lock_acquire+0x1370/0x20d8
 lock_acquire+0x1e8/0x308
 fs_reclaim_acquire+0xd0/0xe4
 __kmem_cache_alloc_node+0x58/0x2d4
 __kmalloc_node_track_caller+0x58/0xf0
 kmemdup+0x34/0x60
 regmap_bulk_write+0x64/0x2c0
 tc358768_bridge_pre_enable+0x8c/0x12d0 [tc358768]
 drm_atomic_bridge_call_pre_enable+0x68/0x80 [drm]
 drm_atomic_bridge_chain_pre_enable+0x50/0x158 [drm]
 drm_atomic_helper_commit_modeset_enables+0x164/0x264 [drm_kms_helper]
 tidss_atomic_commit_tail+0x58/0xc0 [tidss]
 commit_tail+0xa0/0x188 [drm_kms_helper]
 drm_atomic_helper_commit+0x1a8/0x1c0 [drm_kms_helper]
 drm_atomic_commit+0xa8/0xe0 [drm]
 drm_mode_atomic_ioctl+0x9ec/0xc80 [drm]
 drm_ioctl_kernel+0xc4/0x170 [drm]
 drm_ioctl+0x234/0x4b0 [drm]
 drm_compat_ioctl+0x110/0x12c [drm]
 __arm64_compat_sys_ioctl+0x128/0x150
 invoke_syscall+0x48/0x110
 el0_svc_common.constprop.0+0x40/0xe0
 do_el0_svc_compat+0x1c/0x38
 el0_svc_compat+0x48/0xb4
 el0t_32_sync_handler+0xb0/0x138
 el0t_32_sync+0x194/0x198

Fixes: 4d56a4f08391 ("drm/tidss: Annotate dma-fence critical section in commit path")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920-dma-fence-annotation-revert-v1-1-7ebf6f7f5bf6@ideasonboard.com

drm/panfrost: Remove incorrect IS_ERR() check

sg_page_iter_page() doesn't return an error code, so the IS_ERR() check
is wrong and the error path will never be executed. This also allows
simplifying the code to remove the local variable 'page'.

CC: Adrián Larumbe <adrian.larumbe@collabora.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/376713ff-9a4f-4ea3-b097-fb5efb685d95@moroto.mountain
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Tested-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020104405.53992-1-steven.price@arm.com

drm/v3d: wait for all jobs to finish before unregistering

Currently, we are only warning the user if the BIN or RENDER jobs don't
finish before we unregister V3D. We must wait for all jobs to finish
before unregistering. Therefore, warn the user if TFU or CSD jobs
are not done by the time the driver is unregistered.

Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20231023105927.101502-1-mcanal@igalia.com

accel/ivpu: Add support for delayed D0i3 entry message

Currently the VPU firmware prepares for D0i3 every time the VPU
is entering D0i2 Idle state. This is not optimal as we might not
enter D0i3 every time we enter D0i2 Idle and this preparation
is quite costly.

This optimization moves D0i3 preparation to a dedicated
message sent from the host driver only when the driver is about
to enter D0i3 - this reduces power consumption and latency for
certain workloads, for example audio workloads that submit
inference every 10 ms.

The VPU needs non zero time to enter IDLE state after responding to
D0i3 entry message. If the driver does not wait for the VPU to enter
IDLE state it could cause warm boot failures.

Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-12-stanislaw.gruszka@linux.intel.com

accel/ivpu/37xx: Print warning when VPUIP is not idle during power down

Print warning if VPUIP is not idle during power down.

Use warn log level also when we fail to enter reset state
as this is not really an error but unexpected behavior.

Reviewed-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-11-stanislaw.gruszka@linux.intel.com

accel/ivpu: Introduce ivpu_ipc_send_receive_active()

Split ivpu_ipc_send_receive() implementation to have a version
that does not call pm_runtime_resume_and_get(). That implementation
can be invoked when device is up and runtime resume is prohibited
(for example at the end of boot sequence).

The new function will be used for D0i3 entry IPC message addition
in the separate change.

Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-10-stanislaw.gruszka@linux.intel.com

accel/ivpu: Pass D0i3 residency time to the VPU firmware

The firmware needs to know the time spent in D0i3/D3 to
calculate telemetry data. The D0i3/D3 residency time is
calculated by the driver and passed to the firmware
in the boot parameters.

The driver also passes VPU perf counter value captured
right before entering D0i3 - this allows the VPU firmware
to generate monotonic timestamps for the logs.

Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-9-stanislaw.gruszka@linux.intel.com

accel/ivpu/40xx: Capture D0i3 entry host and device timestamps

The driver needs to capture the D0i3 entry timestamp to
calculate D0i3 residency time.

The D0i3 residency time and the VPU timestamp are passed
to the firmware at D0i3 exit (warm boot).

Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-8-stanislaw.gruszka@linux.intel.com

accel/ivpu: Change test_mode module param to bitmask

Change meaning of test_mode module parameter from integer value
to bitmask allowing setting different test features with corresponding
bits.

Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-7-stanislaw.gruszka@linux.intel.com

accel/ivpu: Add support for VPU_JOB_FLAGS_NULL_SUBMISSION_MASK

Add test_mode = 3 that add VPU_JOB_FLAGS_NULL_SUBMISSION_MASK
flag to the job send to the VPU device. Then the VPU will process
the job but won't execute commands (except the command to signal
the fence).

This can be used to estimate job processing overhead in the host
software and VPU firmware.

Unlike the null hardware mode, the null submission mode will
still work even if UMD uses VPU fences to track job completion.

Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-6-stanislaw.gruszka@linux.intel.com

accel/ivpu: Remove reset from power up sequence

Setting a non-zero work point resets the IP hence IP_RESET
trigger is redundant.

Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-5-stanislaw.gruszka@linux.intel.com

accel/ivpu: Add dvfs_mode file to debugfs

Add new debugfs file to set dvfs_mode FW boot parameter and restart
the FW to allow experimenting with DVFS (dynamic voltage & frequency
scaling).

Signed-off-by: Tomasz Rusinowicz <tomasz.rusinowicz@intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-4-stanislaw.gruszka@linux.intel.com

accel/ivpu: Remove unneeded drm_driver declaration

Cleanup drm_driver declaration leftover.

Reviewed-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-3-stanislaw.gruszka@linux.intel.com

accel/ivpu: Update FW API

Bump boot API to 4.20
Bump JSM API to 3.15

Signed-off-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231028133415.1169975-2-stanislaw.gruszka@linux.intel.com

accel/ivpu: avoid build failure with CONFIG_PM=n

The usage count of struct dev_pm_info is an implementation detail that
is only available if CONFIG_PM is enabled, so printing it in a debug message
causes a build failure in configurations without PM:

In file included from include/linux/device.h:15,
                 from include/linux/pci.h:37,
                 from drivers/accel/ivpu/ivpu_pm.c:8:
drivers/accel/ivpu/ivpu_pm.c: In function 'ivpu_rpm_get_if_active':
drivers/accel/ivpu/ivpu_pm.c:254:51: error: 'struct dev_pm_info' has no member named 'usage_count'
  254 |                  atomic_read(&vdev->drm.dev->power.usage_count));
      |                                                   ^
include/linux/dev_printk.h:129:48: note: in definition of macro 'dev_printk'
  129 |                 _dev_printk(level, dev, fmt, ##__VA_ARGS__);            \
      |                                                ^~~~~~~~~~~
drivers/accel/ivpu/ivpu_drv.h:75:17: note: in expansion of macro 'dev_dbg'
   75 |                 dev_dbg((vdev)->drm.dev, "[%s] " fmt, #type, ##args);          \
      |                 ^~~~~~~
drivers/accel/ivpu/ivpu_pm.c:253:9: note: in expansion of macro 'ivpu_dbg'
  253 |         ivpu_dbg(vdev, RPM, "rpm_get_if_active count %d\n",
      |         ^~~~~~~~

The print message does not seem essential, so the easiest workaround is
to just remove it.

Fixes: c39dc15191c4 ("accel/ivpu: Read clock rate only if device is up")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231027152633.528490-1-arnd@kernel.org

drm/panel-edp: Add AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49 V8.0

Add panel identification entry for
- AUO B116XTN02 family (product ID:0x235c)
- BOE NT116WHM-N21,836X2 (product ID:0x09c3)
- BOE NV116WHM-N49 V8.0 (product ID:0x0979)

Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231027110435.1.Ia01fe9ec1c0953e0050a232eaa782fef2c037516@changeid

accel/qaic: Support MHI QAIC_TIMESYNC channel

Use QAIC_TIMESYNC MHI channel to send UTC time to device in SBL
environment. Remove support for QAIC_TIMESYNC MHI channel in AMSS
environment as it is not used in that environment.

Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231016170114.5446-3-quic_jhugo@quicinc.com

accel/qaic: Add support for periodic timesync

Device and Host have a time synchronization mechanism that happens once
during boot when device is in SBL mode. After that, in mission-mode there
is no timesync. In an experiment after continuous operation, device time
drifted w.r.t. host by approximately 3 seconds per day. This drift leads
to mismatch in timestamp of device and Host logs. To correct this
implement periodic timesync in driver. This timesync is carried out via
QAIC_TIMESYNC_PERIODIC MHI channel.

Signed-off-by: Ajit Pal Singh <quic_ajitpals@quicinc.com>
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231016170114.5446-2-quic_jhugo@quicinc.com

accel/qaic: Enable 1 MSI fallback mode

Several virtualization use-cases either don't support 32 MultiMSIs
(Xen/VMware) or have significant drawbacks to their use (KVM's vIOMMU,
which is required to support 32 MSI, needs to allocate an alternate
system memory space for each device using vIOMMU (e.g. 8GB VM mem and
2 cards => 8 + 2 * 8 = 24GB host memory required)). Support these
cases by enabling a 1 MSI fallback mode.

Whenever all 32 MSIs requested are not available, a second request for
a single MSI is made. Its success is the initiator of single MSI mode.
This mode causes all interrupts generated by the device to be directed
to the 0th MSI (firmware >=v1.10 will do this as a response to the PCIe
MSI capability configuration). Likewise, all interrupt handlers for the
device are registered to the 0th MSI.

Since the DBC interrupt handler checks if the DBC is in use or if
there is any pending changes, the 'spurious' interrupts are
disregarded. If there is work to be done, the standard threaded IRQ
handler is dispatched.

On every interrupt, the MHI handler wakes up its threaded interrupt
handler, and attempts to wake any waiters for MHI state events.

Performance is within +-0.6% for test cases that typify real world
use. Larger differences ([-4,+132]%, avg +47%) exist for very simple
tasks (e.g. addition) compiled for single NSPs. It is assumed that the
small work and many interrupts typically cause contention (e.g. 16 NSPs
vs 4 CPUs), as evidenced by the standard deviation between runs also
decreasing (r=-0.48 between delta(Performace_test) and
delta(StdDev_test/Avg_test))

Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Reviewed-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231016170036.5409-1-quic_jhugo@quicinc.com

drm/doc: describe PATH format for DP MST

This is already uAPI, xserver parses it. It's useful to document
since user-space might want to lookup the parent connector.

Additionally, people (me included) have misunderstood the PATH
property for being stable across reboots, but since a KMS object
ID is baked in there that's not the case. So PATH shouldn't be
used as-is in config files and such.

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20231023203629.198109-1-contact@emersion.fr

drm: introduce CLOSEFB IOCTL

This new IOCTL allows callers to close a framebuffer without
disabling planes or CRTCs. This takes inspiration from Rob Clark's
unref_fb IOCTL [1] and DRM_MODE_FB_PERSIST [2].

User-space patch for wlroots available at [3]. IGT test available
at [4].

v2: add an extra pad field just in case we want to extend this IOCTL
in the future (Pekka, Sima).

[1]: https://lore.kernel.org/dri-devel/20170509153654.23464-1-robdclark@gmail.com/
[2]: https://lore.kernel.org/dri-devel/20211006151921.312714-1-contact@emersion.fr/
[3]: https://gitlab.freedesktop.org/wlroots/wlroots/-/merge_requests/4394
[4]: https://lists.freedesktop.org/archives/igt-dev/2023-October/063294.html

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Dennis Filder <d.filder@web.de>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020101926.145327-2-contact@emersion.fr

drm: extract closefb logic in separate function

drm_mode_rmfb performs two operations: drop the FB from the
file_priv->fbs list, and make sure the FB is no longer used on a
plane.

In the next commit an IOCTL which only does so former will be
introduced, so let's split it into a separate function.

No functional change, only refactoring.

v2: no change

Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Dennis Filder <d.filder@web.de>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020101926.145327-1-contact@emersion.fr

drm/atomic-helper: Fix spelling mistake "preceeding" -> "preceding"

There is a typo in the kernel documentation for function
drm_atomic_helper_wait_for_dependencies. Fix it.

Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231027024459.12793-1-chentao@kylinos.cn

drm/ssd130x: Fix possible uninitialized usage of crtc_state variable

Avoid a possible uninitialized use of the crtc_state variable in function
ssd132x_primary_plane_atomic_check() and avoid the following Smatch warn:

    drivers/gpu/drm/solomon/ssd130x.c:921 ssd132x_primary_plane_atomic_check()
    error: uninitialized symbol 'crtc_state'.

Fixes: fdd591e00a9c ("drm/ssd130x: Add support for the SSD132x OLED controller family")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/dri-devel/7dd6ca45-8263-44fe-a318-2fd9d761425d@moroto.mountain/
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020225338.1686974-1-javierm@redhat.com

dt-bindings: display: ssd132x: Remove '-' before compatible enum

This is a leftover from when the binding schema had the compatible string
property enum as a 'oneOf' child and the '-' was not removed when 'oneOf'
got dropped during the binding review process.

Reported-by: Rob Herring <robh@kernel.org>
Closes: https://lore.kernel.org/dri-devel/CAL_Jsq+h8DcnpKqhokQOODCc8+Qi3M0PrxRFKz_Y4v37yMJvvA@mail.gmail.com/
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020223029.1667190-1-javierm@redhat.com

drm/amdgpu: move buffer funcs setting up a level

Rather than doing this in the IP code for the SDMA paging
engine, move it up to the core device level init level.
This should fix the scheduler init ordering.

v2: drop extra parens
v3: drop SDMA helpers
v4: Added a Fixes tag because amdgpu dereferences an uninitialized
    scheduler without this patch, and this patch fixes this. (Luben)

Tested-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20231025171928.3318505-1-alexander.deucher@amd.com
Acked-by: Christian König <christian.koenig@amd.com>
Fixes: 56e449603f0ac5 ("drm/sched: Convert the GPU scheduler to variable number of run-queues")
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>

MAINTAINERS: Update the GPU Scheduler email

Update the GPU Scheduler maintainer email.

Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: AMD Graphics <amd-gfx@lists.freedesktop.org>
Cc: Direct Rendering Infrastructure - Development <dri-devel@lists.freedesktop.org>
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>
Acked-by: Alex Deucher <Alexander.Deucher@amd.com>
Link: https://lore.kernel.org/r/20231026174438.18427-2-ltuikov89@gmail.com

drm/sched: Convert the GPU scheduler to variable number of run-queues

The GPU scheduler has now a variable number of run-queues, which are set up at
drm_sched_init() time. This way, each driver announces how many run-queues it
requires (supports) per each GPU scheduler it creates. Note, that run-queues
correspond to scheduler "priorities", thus if the number of run-queues is set
to 1 at drm_sched_init(), then that scheduler supports a single run-queue,
i.e. single "priority". If a driver further sets a single entity per
run-queue, then this creates a 1-to-1 correspondence between a scheduler and
a scheduled entity.

Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Russell King <linux+etnaviv@armlinux.org.uk>
Cc: Qiang Yu <yuq825@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Emma Anholt <emma@anholt.net>
Cc: etnaviv@lists.freedesktop.org
Cc: lima@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20231023032251.164775-1-luben.tuikov@amd.com

MAINTAINERS: drm/ci: add entries for xfail files

DRM CI keeps track of which tests are failing, flaking or being skipped
by the ci in the expectations files. Add entries for those files to the
corresponding driver maintainer, so they can be notified when they
change.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230919182249.153499-1-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: docs: add step about how to request privileges

Clarify the procedure developer must follow to request privileges to
run tests on Freedesktop gitlab CI.

This measure was added to avoid untrusted people to misuse the
infrastructure.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: David Heidelberg <david.heidelberg@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-11-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: do not automatically retry on error

Since the kernel doesn't use a bot like Mesa that requires tests to pass
in order to merge the patches, leave it to developers and/or maintainers
to manually retry.

Suggested-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: David Heidelberg <david.heidelberg@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-10-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: export kernel config

Export the resultant kernel config, making it easier to verify if the
resultant config was correctly generated.

Suggested-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: David Heidelberg <david.heidelberg@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-9-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: increase i915 job timeout to 1h30m

With the new sharding, the default job timeout is not enough for i915
and their jobs are failing before completing.

See below the current execution time:

🞋 job i915:tgl 8/8 has new status: success (37m3s)
🞋 job i915:tgl 7/8 has new status: success (19m43s)
🞋 job i915:tgl 6/8 has new status: success (21m47s)
🞋 job i915:tgl 5/8 has new status: success (18m16s)
🞋 job i915:tgl 4/8 has new status: success (21m43s)
🞋 job i915:tgl 3/8 has new status: success (17m59s)
🞋 job i915:tgl 2/8 has new status: success (22m15s)
🞋 job i915:tgl 1/8 has new status: success (18m52s)
🞋 job i915:cml 2/2 has new status: success (1h19m58s)
🞋 job i915:cml 1/2 has new status: success (55m45s)
🞋 job i915:whl 2/2 has new status: success (1h8m56s)
🞋 job i915:whl 1/2 has new status: success (54m3s)
🞋 job i915:kbl 3/3 has new status: success (37m43s)
🞋 job i915:kbl 2/3 has new status: success (36m37s)
🞋 job i915:kbl 1/3 has new status: success (34m52s)
🞋 job i915:amly 2/2 has new status: success (1h7m60s)
🞋 job i915:amly 1/2 has new status: success (59m18s)
🞋 job i915:glk 2/2 has new status: success (58m26s)
🞋 job i915:glk 1/2 has new status: success (50m23s)
🞋 job i915:apl 3/3 has new status: success (1h6m39s)
🞋 job i915:apl 2/3 has new status: success (1h4m45s)
🞋 job i915:apl 1/3 has new status: success (1h7m38s)

(generated with ci_run_n_monitor.py script)

The longest job is 1h19m58s, so adjust the timeout.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-8-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: add subset-1-gfx to LAVA_TAGS and adjust shards

The Collabora Lava farm added a tag called `subset-1-gfx` to half of
devices the graphics community use.

Lets use this tag so we don't occupy all the resources.

This is particular important because Mesa3D shares the resources with
DRM-CI and use them to do pre-merge tests, so it can block developers
from getting their patches merged.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: David Heidelberg <david.heidelberg@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-7-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: clean up xfails (specially flakes list)

Since the script that collected the list of the expectation files was
bogus and placing test to the flakes list incorrectly, restart the
expectation files with the correct script.

This reduces a lot the number of tests in the flakes list.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: David Heidelberg <david.heidelberg@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-6-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: uprev IGT and make sure core_getversion is run

IGT has recently merged a patch that makes code_getversion test to fails
if the driver isn't loaded or if it isn't the expected one defined in
variable IGT_FORCE_DRIVER.

Without this test, jobs were passing when the driver didn't load or
probe for some reason, giving the illusion that everything was ok.

Uprev IGT to include this modification and include core_getversion test
in all the shards.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: David Heidelberg <david.heidelberg@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-5-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: add helper script update-xfails.py

Add helper script that given a gitlab pipeline url, analyse which are
the failures and flakes and update the xfails folder accordingly.

Example:
Trigger a pipeline in gitlab infrastructure, than re-try a few jobs more
than once (so we can have data if failures are consistent across jobs
with the same name or if they are flakes) and execute:

update-xfails.py https://gitlab.freedesktop.org/helen.fornazier/linux/-/pipelines/970661

git diff should show you that it updated files in xfails folder.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: Vignesh Raman <vignesh.raman@collabora.com>
Reviewed-by: David Heidelberg <david.heidelberg@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-4-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: fix DEBIAN_ARCH and get amdgpu probing

amdgpu driver wasn't loading because amdgpu firmware wasn't being
installed in the rootfs due to the wrong DEBIAN_ARCH variable.

rename ARCH to DEBIAN_ARCH also, so we don't have the confusing
DEBIAN_ARCH, KERNEL_ARCH and ARCH.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: David Heidelberg <david.heidelberg@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-3-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: uprev mesa version: fix container build & crosvm

When building containers, some rust packages were installed without
locking the dependencies version, which got updated and started giving
errors like:

error: failed to compile `bindgen-cli v0.62.0`, intermediate artifacts can be found at `/tmp/cargo-installkNKRwf`
Caused by:
  package `rustix v0.38.13` cannot be built because it requires rustc 1.63 or newer, while the currently active rustc version is 1.60.0

A patch to Mesa was added fixing this error, so update it.

Also, commit in linux kernel 6.6 rc3 broke booting in crosvm.
Mesa has upreved crosvm to fix this issue.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
[crosvm mesa update]
Co-Developed-by: Vignesh Raman <vignesh.raman@collabora.com>
Signed-off-by: Vignesh Raman <vignesh.raman@collabora.com>
[v1 container build uprev]
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Acked-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: David Heidelberg <david.heidelberg@collabora.com>
Link: https://lore.kernel.org/r/20231024004525.169002-2-helen.koike@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: Enable CONFIG_BACKLIGHT_CLASS_DEVICE

Dependency for CONFIG_DRM_PANEL_EDP.  Missing this was causing the drm
driver to not probe on devices that use panel-edp.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/20231002164715.157298-1-robdclark@gmail.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: force-enable CONFIG_MSM_MMCC_8996 as built-in

Enable CONFIG_MSM_MMCC_8996, the multimedia clock controller on Qualcomm
MSM8996 to prevent the the board from hitting the probe deferral
timeouts in CI run.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/20231008132320.762542-2-dmitry.baryshkov@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/ci: pick up -external-fixes from the merge target repo

In case of the merge requests it might be useful to push repo-specific
fixes which have not yet propagated to the -external-fixes branch in the
main UPSTREAM_REPO. For example, in case of drm/msm development, we are
staging fixes locally for testing, before pushing them to the drm/drm
repo. Thus, if the CI run was triggered by merge request, also pick up
the -external fixes basing on the the CI_MERGE target repo / and branch.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/20231008132320.762542-1-dmitry.baryshkov@linaro.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/doc: ci: Require more context for flaky tests

Flaky tests can be very difficult to reproduce after the facts, which
will make it even harder to ever fix.

Let's document the metadata we agreed on to provide more context to
anyone trying to address these fixes.

Link: https://lore.kernel.org/dri-devel/CAPj87rPbJ1V1-R7WMTHkDat2A4nwSd61Df9mdGH2PR=ZzxaU=Q@mail.gmail.com/
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231025142441.745947-1-mripard@kernel.org