hpsa: add discovery polling for PT RAID devices.

There are problems with getting configuration change notification
in pass-through RAID environments.  So, activate flag
h->discovery_polling when one of these devices is detected in
update_scsi_devices.

After discovery_polling is set, execute a report luns from
rescan_controller_worker (every 30 seconds).

If the data from report_luns is different than last
time (binary compare), execute a full rescan via update_scsi_devices.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: eliminate fake lun0 enclosures

We don't need to create fake enclosure devices at Lun0
in external target array configurations anymore.
This was done to support Pre-SCSI rev 5 controllers
that didn't suppoprt report luns commands, so the
SCSI layer had to scan targets. If there was no
LUN at LUN 0, then the target scan would stop, and
move to the next target.  Lun0 enclosure device
was added to prevent sparsely-numbered LUNs from
being missed.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: generalize external arrays

External array LUNs must use target and lun numbers assigned by the
external array. So the driver must treat these differently from
local LUNs when assigning lun/target.

LUN's 'model' field has been used to detect Lun types that need
special treatment, but the desire is to eliminate the need to reference
specific array models, and support any external array.

Pass-through RAID (PTRAID) luns are not luns of the local controller,
so they are not reported in LUN count of command 'ID controller'.
However, they ARE reported in "Report logical Luns" command.
Local luns are listed first, then PTRAID LUNs.

The number of luns from "Report LUNs" in excess of those reported by
'ID controller' are therefore the PTRAID LUNS.

We can now remove function is_ext_target, and the 'white list'
array of supported model names.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: move scsi_add_device and scsi_remove_device calls to new function

preparation for adding the sas transport class

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: refactor hpsa_figure_bus_target_lun

setup for sas transport. Need to set the
bus and target accordingly.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: enhance hpsa_get_device_id

use an index into vpd data for SAS/SATA drives

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: add function is_logical_device

simplify checking for logical/physical devices

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: simplify update scsi devices

remove repeated calculation that checks for physical
or logical devices.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: simplify check for device exposure

remove macros and cleanup device exposure checking

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: correct ioaccel2 sg chain len

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: correct check for non-disk devices

The driver is using two MACROs which seemingly are looking in
the wrong location for the device_flags returned from
CISS_REPORT_PHYS. Both MACROs, NON_DISK_PHYS_DEV and
PHYS_IOACCEL, are using the pointer returned from figure_lunaddrbytes
which is the address of the LUN.lunid element in
the extended CISS_REPORT_PHYS.  But the MACROS are using offsets
beyond the range of the element (offset 17 of an 8 byte element).

These MACROs actually are looking at the correct location but
they fail static checker analysis. It also will not work
if any new elements are added to the extended LUN structure.

Change the code to use the structure elements directly
since this MACRO is only used in one location.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: fix physical target reset

Set reset type in device_reset_handler to do either
logical unit reset for logical devices, or physical
target reset, for physical devices.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: fix hpsa_adjust_hpsa_scsi_table

Fix a NULL pointer issue in the driver when devices are removed
during a reset.

Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: correct transfer length for 6 byte read/write commands

handle block counts of 0. Cleanup block and block count calculations.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: abandon rescans on memory alloaction failures.

Abandon and reschedule rescan process only if device inquiries
fail due to mem alloc failures, which are likely to occur for
all devices.

Otherwise, skip device if inquiry fails for other reasons,
and continue rescanning process for other devices.

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: allow driver requested rescans

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by; Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: fix null device issues

Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: check for null arguments to dev_printk

Check for NULLs.

Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: change devtype to unsigned

This member is used in calls to scsi_device_type.
It should be unsigned since the kernel checks for upper bounds
and it should never be negative.

Suggested-by: Tomas Henzl <thenzl@redhat.com>
Suggested-by: Hannes Reinecke <hare@suse.de>
Suggested-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: remove unused hpsa_tag_discard_error_bits

This function is no longer used.

Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: stop zeroing reset_cmds_out and ioaccel_cmds_out during rescan

pulling the rug out from under the reset handler
likewise for ioaccel_cmds_out

Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hpsa: remove unused parameter hostno

This parameter was once used before scan_start was defined
but now it is no longer used.

Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_sysfs: Fix queue_ramp_up_period return code

Writing a number to /sys/bus/scsi/devices/<sdev>/queue_ramp_up_period
returns the value of that number instead of the number of bytes written.
This behavior can confuse programs expecting POSIX write() semantics.
Fix this by returning the number of bytes written instead.

Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: Export SCSI Inquiry data to sysfs

Export the RAW SCSI Inquiry to sysfs as binfile. This way the data can be used
by userland without the need to have and ioctl or use the sg_inq tool.

Here is an example of the provided data

linux:~ # hexdump /sys/class/scsi_device/1\:0\:0\:0/device/inquiry
0000000 8005 3205 001f 0000 4551 554d 2020 2020
0000010 4551 554d 4420 4456 522d 4d4f 2020 2020
0000020 2e32 2e33
0000024

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Fix sparse warning

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Make tape drives visible on PERC5 controllers

The DELL PERC5 controller firmware does not list tape drives in response
to MR_DCMD_PD_LIST_QUERY. This causes tape drives not be exposed to the
OS when connected to a PERC5 controller.

This patch permits detection of tape drives connected to a PERC5
controller by exposing non-TYPE_DISK devices unconditionally.

Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

sg: Fix double-free when drives detach during SG_IO

In sg_common_write(), we free the block request and return -ENODEV if
the device is detached in the middle of the SG_IO ioctl().

Unfortunately, sg_finish_rem_req() also tries to free srp->rq, so we
end up freeing rq->cmd in the already free rq object, and then free
the object itself out from under the current user.

This ends up corrupting random memory via the list_head on the rq
object. The most common crash trace I saw is this:

  ------------[ cut here ]------------
  kernel BUG at block/blk-core.c:1420!
  Call Trace:
  [<ffffffff81281eab>] blk_put_request+0x5b/0x80
  [<ffffffffa0069e5b>] sg_finish_rem_req+0x6b/0x120 [sg]
  [<ffffffffa006bcb9>] sg_common_write.isra.14+0x459/0x5a0 [sg]
  [<ffffffff8125b328>] ? selinux_file_alloc_security+0x48/0x70
  [<ffffffffa006bf95>] sg_new_write.isra.17+0x195/0x2d0 [sg]
  [<ffffffffa006cef4>] sg_ioctl+0x644/0xdb0 [sg]
  [<ffffffff81170f80>] do_vfs_ioctl+0x90/0x520
  [<ffffffff81258967>] ? file_has_perm+0x97/0xb0
  [<ffffffff811714a1>] SyS_ioctl+0x91/0xb0
  [<ffffffff81602afb>] tracesys+0xdd/0xe2
    RIP [<ffffffff81281e04>] __blk_put_request+0x154/0x1a0

The solution is straightforward: just set srp->rq to NULL in the
failure branch so that sg_finish_rem_req() doesn't attempt to re-free
it.

Additionally, since sg_rq_end_io() will never be called on the object
when this happens, we need to free memory backing ->cmd if it isn't
embedded in the object itself.

KASAN was extremely helpful in finding the root cause of this bug.

Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: avoid a panic if MSI(X) interrupts are disabled

If MSI(X) interrupts are disabled via the kernel command line
(pci=nomsi), the pm8001 driver will kernel panic because it does not
detect that MSI interrupts are disabled and will soldier on and attempt to
configure MSI interrupts anyways.  This leads to a kernel panic, most
likely because a required data structure is not available down the
line.  Using the pci_msi_enabled() function in order to detect if MSI
interrupts are enabled before configuring them resolves this issue and
avoids a kernel panic when the module is loaded.  Additionally, the
irq_vector structure must be initialized when legacy interrupts are
being used otherwise legacy interrupts will simply not function and
result in another panic.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: wait a minimum of 500ms before issuing commands to SPCv

The documentation for the 8070 and 8072 SPCv chip explicitly states that
a minimum of 500ms must elapse before issuing commands, otherwise the
SPCv may not process them and the firmware may get into an unrecoverable
state requiring a reboot.  While the Linux guys will probably think this
is 'racy', it is called out in the chip documentation and inserting this
delay makes power management function properly.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: do not examine registers for iButton feature if ATTO adapter

ATTO adapters do not support this feature.  If the firmware fails to be
ready, it should not check the examined registers in order to examine
the state of the feature in order to prevent undefined behavior.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: set PHY profiles for ATTO 12Gb SAS controllers

PHY profiles are not saved in NVRAM on ATTO 12Gb SAS controllers.
Therefore, in order for the controller to function in a wide range of
configurations, the PHY profiles must be statically set.  This patch
provides the necessary functionality to do so.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: add support for ATTO devices during SAS address initiailization

ATTO SAS controllers retrieve the SAS address from the NVRAM in a location
different from non-ATTO PMC Sierra SAS controllers.  This patch makes the
necessary adjustments in order to retrieve the SAS address on these types
of adapters.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: add ATTO PCI IDs to pm8001_pci_table

These PCI IDs allow the pm8001 driver to load against ATTO 12Gb SAS
controllers that use PMC Sierra 8070 and PMC Sierra 8072 SAS chips.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: add support for PMC Sierra 8070 and PMC Sierra 8072 SAS controllers

These SAS controllers support speeds up to 12Gb.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm80xx: configure PHY settings based on subsystem vendor ID

Previuosly, all PMC Sierra 80xx controllers are assumed to be a
motherboard controller, except if the subsystem vendor ID was equal to
PCI_VENDOR_ID_ADAPTEC.  The driver then attempts to load PHY settings
from NVRAM.  While this may be correct behavior for most controllers, it
does not work with Adaptec and ATTO controllers since they do not store
PHY settings in NVRAM and choose to use either custom PHY settings or
chip defaults.  Loading random values from NVRAM may cause the
controllers to malfunction in this edge case.

Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

SCSI: Increase REPORT_LUNS timeout

This patch fixes an issue seen with an IBM 2145 (SVC) where, following an error
injection test which results in paths going offline, when they came
back online, the path would timeout the REPORT_LUNS issued during the
scan. This timeout situation continued until retries were expired, resulting in
falling back to a sequential LUN scan. Then, since the target responds
with PQ=1, PDT=0 for all possible LUNs, due to the way the sequential
LUN scan code works, we end up adding 512 LUNs for each target, when there
is really only a small handful of LUNs that are actually present.

This patch increases the timeout used on the REPORT_LUNS to 30 seconds.
This patch solves the issue of 512 non existent LUNs showing up after
this event.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas : Remove debug print from function megasas_update_span_set

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas : Driver version upgrade

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas : SMAP restriction--do not access user memory from IOCTL code

This is an issue on SMAP enabled CPUs and 32 bit apps running on 64 bit
OS. Do not access user memory from kernel code. The SMAP bit restricts
accessing user memory from kernel code.

Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Make PI enabled VD 8 byte DMA aligned

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Initialize tasklet before setting up IRQs

It may happen (kdump), that an interrupt is invoked just after the
setup_irqs function was called but before the tasklet was initialised.
At this phase the hw ints should have been disabled, but for unknown
reason this mechanism seems to not work properly.

From: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Indicate online firmware upgrade support for Secure JBOD feature

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Update OCR capability on controller properties change

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Do not use PAGE_SIZE for max_sectors

Do not use PAGE_SIZE marco to calculate max_sectors per I/O
request. Driver code assumes PAGE_SIZE will be always 4096 which can
lead to wrongly calculated value if PAGE_SIZE is not 4096. This issue
was reported in Ubuntu Bugzilla Bug #1475166.

Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Support for Cutlass (12 Gbps) controller

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Support for Intruder (12 Gbps) controller

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Remove PCI id checks

Remove PCI id based checks and use instance->ctrl_context to decide
whether controller is MFI-based or a Fusion adapter. Additionally,
Fusion adapters are divided into two categories: Thunderbolt and
Invader.

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Expose TAPE drives unconditionally

Expose non-disk (TAPE drive, CD-ROM) unconditionally.

Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Version update

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Code refactor for use of requestorId

Some of these code changes were proposed by David Binderman.

Removed redudant check of requestorId. Redundant condition:
instance.requestorId. Check for plasma firmware 1.11 are now
restructured to support only specific device id.

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Fix validHandles check in I/O path

Syncro firmware supports round robin I/O switching on dual path. Driver
uses validHandles to check for dual path. However, it is supposed to
check for values > 1 (not > 2).

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Print critical firmware event messages

Print firmware events in human-readable form. This will help users track
any critical firmware events without special application support.

Sample syslogd output:

megaraid_sas 0000:02:00.0: 8619 (491648347s/0x0020/WARN) - Controller temperature threshold exceeded. This may indicate inadequate system cooling. Switching to low performance mode.

The format of logged events is:

"<pci_dev_id>: <sequence_number> (<timestamp>/<locale>/<class>) - <description>"

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Chip reset if driver fails to get IOC ready

Fix the issue reported at:

http://marc.info/?l=linux-scsi&m=143694494104544&w=2

Try to do chip reset at driver load time. If firmware fails to reach
ready state, try chip reset using adp_reset() callback. For Fusion
adapters the call back was previously void. Provide a suitable reset
function.

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Support for max_io_size 1MB

Driver will expose max sge = 256 (earlier it was 64) if firmware
supports extended IO size (1M).

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Code cleanup-use local variable drv_ops inside megasas_ioc_init_fusion

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: JBOD sequence number support

Implemented JBOD map which will provide quick access for JBOD path and
also provide sequence number.  This will help hardware to fail command
to the FW in case of any sequence mismatch.

Fast Path I/O for JBOD will refer JBOD map (which has sequence number
per JBOD device) instead of RAID map.  Previously, the driver used RAID
map to get device handle for fast path I/O and this not have sequence
number information. Now, driver will use JBOD map instead.  As part of
error handling, if JBOD map is failed/not supported by firmware, driver
will continue using legacy behavior.

Now there will be three IO paths for JBOD (syspd):

 - JBOD map with sequence number (Fast Path)
 - RAID map without sequence number (Fast Path)
 - FW path via h/w exception queue deliberately setup devhandle
   0xFFFF (FW path).

Relevant data structures:

 - Driver send new DCMD MR_DCMD_SYSTEM_PD_MAP_GET_INFO for this purpose.
 - struct MR_PD_CFG_SEQ- This structure represent map of single physical
   device.
 - struct MR_PD_CFG_SEQ_NUM_SYNC- This structure represent whole JBOD
   map in general(size, count of sysPDs configured, struct MR_PD_CFG_SEQ
   of syspD with 0 index).
 - JBOD sequence map size is: sizeof(struct MR_PD_CFG_SEQ_NUM_SYNC)
   + (sizeof(struct MR_PD_CFG_SEQ) * (MAX_PHYSICAL_DEVICES - 1)) which
   is allocated while setting up JBOD map at driver load time.

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Increase timeout to 60 secs for abort frames during shutdown

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Synchronize driver headers with firmware APIs

Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

SCSI: fix bug in scsi_dev_info_list matching

The "compatible" matching algorithm used for looking up old-style
blacklist entries in a scsi_dev_info_list is buggy.  The core of the
algorithm looks like this:

if (memcmp(devinfo->vendor, vendor,
    min(max, strlen(devinfo->vendor))))
/* not a match */

where max is the length of the device's vendor string after leading
spaces have been removed but trailing spaces have not.  Because of the
min() computation, either entry could be a proper substring of the
other and the code would still think that they match.

In the case originally reported, the device's vendor and product
strings were "Inateck " and "                ".  These matched against
the following entry in the global device list:

{"", "Scanner", "1.80", BLIST_NOLUN}

because "" is a substring of "Inateck " and "" (the result of removing
leading spaces from the device's product string) is a substring of
"Scanner".  The mistaken match prevented the system from scanning and
finding the device's second Logical Unit.

This patch fixes the problem by making two changes.  First, the code
for leading-space removal is hoisted out of the loop.  (This means it
will sometimes run unnecessarily, but since a large percentage of all
lookups involve the "compatible" entries in global device list, this
should be an overall improvement.)  Second and more importantly, the
patch removes trailing spaces and adds a check to verify that the two
resulting strings are exactly the same length.  This prevents matches
where one entry is a proper substring of the other.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Giulio Bernardi <ugilio@gmail.com>
Tested-by: Giulio Bernardi <ugilio@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

SCSI: refactor device-matching code in scsi_devinfo.c

In drivers/scsi/scsi_devinfo.c, the scsi_dev_info_list_del_keyed() and
scsi_get_device_flags_keyed() routines contain a large amount of
duplicate code for finding vendor/product matches in a
scsi_dev_info_list.  This patch factors out the duplicate code and
puts it in a separate function, scsi_dev_info_list_find().

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Giulio Bernardi <ugilio@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

fnic: check pci_map_single() return value

the kernel prints some warnings when compiled with CONFIG_DMA_API_DEBUG.
This is because the fnic driver doesn't check the return value of
pci_map_single().

[   11.942770] scsi host12: fnic
[   11.950811] ------------[ cut here ]------------
[   11.950818] WARNING: at lib/dma-debug.c:937 check_unmap+0x47b/0x920()
[   11.950821] fnic 0000:0c:00.0: DMA-API: device driver failed to check map error[device address=0x0000002020a30040] [size=44 bytes] [mapped as single]

Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed By: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

be2iscsi: Revert ownership to Emulex

We would like to get the following updates in:
    Revert ownership to "Emulex" from "Avago Technologies"

Signed-off-by: Ketan Mukadam <ketan.mukadam@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

MAINTAINERS: Update be2iscsi driver

Signed-off-by: Ketan Mukadam <ketan.mukadam@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

bnx2fc: Do not log error for netevents that need no action

Do not log error for netevents that need no action such as
NETDEV_REGISTER 0x0005, NETDEV_CHANGEADDR, and NETDEV_CHANGENAME.
It results in logging error messages such as these

[   35.315872] bnx2fc: Unknown netevent 5
[   35.315935] bnx2fc: Unknown netevent 8
[   35.353866] bnx2fc: Unknown netevent 10

and generating bug reports.
Remove logging this message as an ERROR instead of turning them into
either DEBUG or INFO level messages.

Signed-off-by: Shirish Pargaonkar <spargaonkar@suse.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: Update version to 11.0.0.0 for upstream patch set

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: Fix default RA_TOV and ED_TOV in the FC/FCoE driver for all topologies

Initial link up defaults were not properly being tracked relative to
initial FLOGI or pt2pt PLOGI. Add code to initialize them.

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: The linux driver does not reinitiate discovery after a failed FLOGI

Forgot to clear FCF Discovery in-progress flag upon FLOGI failures.
Thus we didn't restart FLOGI.

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: Fix for discovery failure in PT2PT when FLOGI's ELS ACC response gets aborted

Fix for discovery failure in PT2PT when FLOGI's ELS ACC response gets aborted

Change login state machine to:
- Restart FLOGI if prior is ABTS'd
- Reject incoming FLOGIs if we have one pending

The above ensures that we always finish FLOGI processing, regardless
of who initated FLOGI, before processing PLOGI's.

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: Add support for Lancer G6 and 32G FC links

Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

fix: lpfc_send_rscn_event sends bigger buffer size

lpfc_send_rscn_event() allocates data for sizeof(struct
lpfc_rscn_event_header) + payload_len, but claims that the data has size
of sizeof(struct lpfc_els_event_header) + payload_len. That leads to
buffer overruns.

Signed-off-by: Ales Novak <alnovak@suse.cz>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: remove set but not used variables

Remove set but not used variables.

Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc:Make the function lpfc_sli4_mbox_completions_pending static in order to comply with function prototype

This makes the function lpfc_sli4_mbox_completion's definition
static now in order to comply with its prototype being also
declared as static too.

Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

Fix kmalloc overflow in LPFC driver at large core count

This patch allows the LPFC to start up without a fatal kernel bug based
on an exceeded KMALLOC_MAX_SIZE and a too large NR_CPU-based maskbits
field. The bug was based on the number of CPU cores in a system.
Using the get_cpu_mask() function declared in kernel/cpu.c allows the
driver to load on the community kernel 4.2 RC1.

Below is the kernel bug reproduced:

8<--------------------------------------------------------------------
2199382.828437 (    0.005216)| lpfc 0003:02:00.0: enabling device (0140 -> 0142)
2199382.999272 (    0.170835)| ------------[ cut here ]------------
2199382.999337 (    0.000065)| WARNING: CPU: 84 PID: 404 at mm/slab_common.c:653 kmalloc_slab+0x2f/0x89()
2199383.004534 (    0.005197)| Modules linked in: lpfc(+) usbcore(+) mptctl scsi_transport_fc sg lpc_ich i2c_i801 usb_common tpm_tis mfd_core tpm acpi_cpufreq button scsi_dh_alua scsi_dh_rdacusbcore: registered new device driver usb
2199383.020568 (    0.016034)|
2199383.020581 (    0.000013)|  scsi_dh_hp_sw scsi_dh_emc scsi_dh gru thermal sata_nv processor piix fan thermal_sysehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
2199383.035288 (    0.014707)|
2199383.035306 (    0.000018)|  hwmon ata_piix
2199383.035336 (    0.000030)| CPU: 84 PID: 404 Comm: kworker/84:0 Not tainted 3.18.0-rc2-gat-00106-ga7ca10f-dirty #178
2199383.047077 (    0.011741)| ehci-pci: EHCI PCI platform driver
2199383.047134 (    0.000057)| Hardware name: SGI UV2000/ROMLEY, BIOS SGI UV 2000/3000 series BIOS 01/15/2013
2199383.056245 (    0.009111)| Workqueue: events work_for_cpu_fn
2199383.066174 (    0.009929)|  000000000000028d ffff88eef827bbe8 ffffffff815a542f 000000000000028d
2199383.069545 (    0.003371)|  ffffffff810ea142 ffff88eef827bc28 ffffffff8104365c ffff88eefe4006c8
2199383.076214 (    0.006669)|  0000000000000000 00000000000080d0 0000000000000000 0000000000000004
2199383.079213 (    0.002999)| Call Trace:
2199383.084084 (    0.004871)|  [<ffffffff815a542f>] dump_stack+0x49/0x62
2199383.087283 (    0.003199)|  [<ffffffff810ea142>] ? kmalloc_slab+0x2f/0x89
2199383.091415 (    0.004132)|  [<ffffffff8104365c>] warn_slowpath_common+0x77/0x92
2199383.095197 (    0.003782)|  [<ffffffff8104368c>] warn_slowpath_null+0x15/0x17
2199383.103336 (    0.008139)|  [<ffffffff810ea142>] kmalloc_slab+0x2f/0x89
2199383.107082 (    0.003746)|  [<ffffffff8110fd9e>] __kmalloc+0x13/0x16a
2199383.112531 (    0.005449)|  [<ffffffffa01a8ed9>] lpfc_pci_probe_one_s4+0x105b/0x1644 [lpfc]
2199383.115316 (    0.002785)|  [<ffffffff81302b92>] ? pci_bus_read_config_dword+0x75/0x87
2199383.123431 (    0.008115)|  [<ffffffffa01a951f>] lpfc_pci_probe_one+0x5d/0xcb5 [lpfc]
2199383.127364 (    0.003933)|  [<ffffffff81497119>] ? dbs_check_cpu+0x168/0x177
2199383.136438 (    0.009074)|  [<ffffffff81496fa5>] ? gov_queue_work+0xb4/0xc0
2199383.140407 (    0.003969)|  [<ffffffff8130b2a1>] local_pci_probe+0x1e/0x52
2199383.143105 (    0.002698)|  [<ffffffff81052c47>] work_for_cpu_fn+0x13/0x1b
2199383.147315 (    0.004210)|  [<ffffffff81054965>] process_one_work+0x222/0x35e
2199383.151379 (    0.004064)|  [<ffffffff81054e76>] worker_thread+0x3d5/0x46e
2199383.159402 (    0.008023)|  [<ffffffff81054aa1>] ? process_one_work+0x35e/0x35e
2199383.163097 (    0.003695)|  [<ffffffff810599c6>] kthread+0xc8/0xd2
2199383.167476 (    0.004379)|  [<ffffffff810598fe>] ? kthread_freezable_should_stop+0x5b/0x5b
2199383.176434 (    0.008958)|  [<ffffffff815a8cac>] ret_from_fork+0x7c/0xb0
2199383.180086 (    0.003652)|  [<ffffffff810598fe>] ? kthread_freezable_should_stop+0x5b/0x5b
2199383.192333 (    0.012247)| ehci-pci 0000:00:1a.0: EHCI Host Controller
-------------------------------------------------------------------->8

The proposed solution was approved by James Smart at Emulex and tested
on a UV2 machine with 6144 cores. With the fix, the LPFC module loads
with no unwanted effects on the system.

Signed-off-by: Ian Mitchell <imitchell@sgi.com>
Signed-off-by: Alex Thorlton <athorlton@sgi.com>
Suggested-by: Robert Elliot <elliott@hp.com>
[james.smart: resolve unused variable warning]
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: Destroy lpfc_hba_index IDR on module exit

Destroy lpfc_hba_index IDR on module exit, reclaiming the allocated memory.

This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@

module_init(init);

@ defines_module_exit @
identifier exit;
@@

module_exit(exit);

@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@

DEFINE_IDR(idr);

@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 idr_destroy(&idr);
 ...
}

@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 +idr_destroy(&idr);
}
</SmPL>

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: in sli3 use configured sg_seg_cnt for sg_tablesize

Currently the module parameter lpfc_sg_seg_count does not have effect
for sli3 devices.

In lpfc_sli_driver_resource_setup(), which is used for sli3, the code
writes the configured sg_seg_cnt into lpfc_template.sg_tablesize.
But lpfc_template is the template used for sli4 only. Thus the value should
correctly be written to lpfc_template_s3->sg_tablesize.

This patch is for kernel 4.1-rc5, but is tested with lpfc 10.2.405.26 only.

Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: Remove unnessary cast

kzalloc() returns a void pointer - no need to cast it in
drivers/scsi/lpfc/lpfc_init.c::lpfc_sli_driver_resource_setup()

Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

lpfc: fix model description

Remove trailing space from model description.

Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

3w-9xxx: don't unmap bounce buffered commands

3w controller don't dma map small single SGL entry commands but instead
bounce buffer them.  Add a helper to identify these commands and don't
call scsi_dma_unmap for them.

Based on an earlier patch from James Bottomley.

Fixes: 118c85 ("3w-9xxx: fix command completion race")
Reported-by: Tóth Attila <atoth@atoth.sote.hu>
Tested-by: Tóth Attila <atoth@atoth.sote.hu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

scsi_dh: Use the correct module name when loading device handler

This fixes a bug in recent kernels which results in failure to boot
on systems that have multipath SCSI disks.  I observed this failure
on a POWER8 server where all the disks are multipath SCSI disks.
The symptoms are several messages like this on the console:

[    3.018700] device-mapper: table: 253:0: multipath: error attaching hardware handler
[    3.018828] device-mapper: ioctl: error adding target to table

and the system does not find its disks, and therefore fails to boot.

Bisection revealed that the bug was introduced in commit 566079c849cf,
"dm-mpath, scsi_dh: request scsi_dh modules in scsi_dh, not dm-mpath".
The specific reason for the failure is that where we previously loaded
the "scsi_dh_alua" module, we are now trying to load the "alua" module,
which doesn't exist.

To fix this, we change the request_module call in scsi_dh_lookup()
to prepend "scsi_dh_" to the name, just like the old code in
drivers/md/dm-mpath.c:parse_hw_handler() used to do.

[jejb: also fixes issue spotted by Sasha Levin that formatting
characters could be passed in via sysfs and cause issues with
request_module()]

Fixes: 566079c849cf
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

libiscsi: Fix iscsi_check_transport_timeouts possible infinite loop

Connection last_ping is not being updated when iscsi_send_nopout fails.
Not updating the last_ping will cause firing a timer to a past time
(last_ping + ping_tmo < current_time) which triggers an infinite loop of
iscsi_check_transport_timeouts() and hogs the cpu.

Fix this issue by checking the return value of iscsi_send_nopout.
If it fails set the next_timeout to one second later.

Signed-off-by: Ariel Nahum <arieln@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

Linux 4.3-rc1

Merge tag 'cris-for-4.3' of git://git./linux/kernel/git/jesper/cris

Pull CRIS updates from Jesper Nilsson:
 "Mostly removal of old cruft of which we can use a generic version, or
  fixes for code not commonly run in the cris port, but also additions
  to enable some good debug"

* tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits)
  CRISv10: delete unused lib/dmacopy.c
  CRISv10: delete unused lib/old_checksum.c
  CRIS: fix switch_mm() lockdep splat
  CRISv32: enable LOCKDEP_SUPPORT
  CRIS: add STACKTRACE_SUPPORT
  CRISv32: annotate irq enable in idle loop
  CRISv32: add support for irqflags tracing
  CRIS: UAPI: use generic types.h
  CRIS: UAPI: use generic shmbuf.h
  CRIS: UAPI: use generic msgbuf.h
  CRIS: UAPI: use generic socket.h
  CRIS: UAPI: use generic sembuf.h
  CRIS: UAPI: use generic sockios.h
  CRIS: UAPI: use generic auxvec.h
  CRIS: UAPI: use generic headers via Kbuild
  CRIS: UAPI: fix elf.h export
  CRIS: don't make asm/elf.h depend on asm/user.h
  CRIS: UAPI: fix ptrace.h
  CRISv32: Squash compile warnings for axisflashmap
  CRISv32: Add GPIO driver to the default configs
  ...

blk: rq_data_dir() should not return a boolean

rq_data_dir() returns either READ or WRITE (0 == READ, 1 == WRITE), not
a boolean value.

Now, admittedly the "!= 0" doesn't really change the value (0 stays as
zero, 1 stays as one), but it's not only redundant, it confuses gcc, and
causes gcc to warn about the construct

    switch (rq_data_dir(req)) {
        case READ:
            ...
        case WRITE:
            ...

that we have in a few drivers.

Now, the gcc warning is silly and stupid (it seems to warn not about the
switch value having a different type from the case statements, but about
_any_ boolean switch value), but in this case the code itself is silly
and stupid too, so let's just change it, and get rid of warnings like
this:

  drivers/block/hd.c: In function ‘hd_request’:
  drivers/block/hd.c:630:11: warning: switch condition has boolean value [-Wswitch-bool]
     switch (rq_data_dir(req)) {

The odd '!= 0' came in when "cmd_flags" got turned into a "u64" in
commit 5953316dbf90 ("block: make rq->cmd_flags be 64-bit") and is
presumably because the old code (that just did a logical 'and' with 1)
would then end up making the type of rq_data_dir() be u64 too.

But if we want to retain the old regular integer type, let's just cast
the result to 'int' rather than use that rather odd '!= 0'.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'writeback-plugging'

Fix up the writeback plugging introduced in commit d353d7587d02
("writeback: plug writeback at a high level") that then caused problems
due to the unplug happening with a spinlock held.

* writeback-plugging:
  writeback: plug writeback in wb_writeback() and writeback_inodes_wb()
  Revert "writeback: plug writeback at a high level"

writeback: plug writeback in wb_writeback() and writeback_inodes_wb()

We had to revert the pluggin in writeback_sb_inodes() because the
wb->list_lock is held, but we could easily plug at a higher level before
taking that lock, and unplug after releasing it.  This does that.

Chris will run performance numbers, just to verify that this approach is
comparable to the alternative (we could just drop and re-take the lock
around the blk_finish_plug() rather than these two commits.

I'd have preferred waiting for actual performance numbers before picking
one approach over the other, but I don't want to release rc1 with the
known "sleeping function called from invalid context" issue, so I'll
pick this cleanup version for now.  But if the numbers show that we
really want to plug just at the writeback_sb_inodes() level, and we
should just play ugly games with the spinlock, we'll switch to that.

Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

thermal: fix intel PCH thermal driver mismerge

I didn't notice this when merging the thermal code from Zhang, but his
merge (commit 5a924a07f882: "Merge branches 'thermal-core' and
'thermal-intel' of .git into next") of the thermal-core and
thermal-intel branches was wrong.

In thermal-core, commit 17e8351a7739 ("thermal: consistently use int for
temperatures") converted the thermal layer to use "int" for
temperatures.

But in parallel, in the thermal-intel branch commit d0a12625d2ff
("thermal: Add Intel PCH thermal driver") added support for the intel
PCH thermal sensor using the old interfaces that used "unsigned long"
pointers.

This resulted in warnings like this:

  drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
    .get_temp = pch_thermal_get_temp,
                ^
  drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’)
  drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
    .get_trip_temp = pch_get_trip_temp,
                     ^
  drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’)

This fixes it.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'akpm' (patches from Andrew)

Merge fourth patch-bomb from Andrew Morton:

 - sys_membarier syscall

 - seq_file interface changes

 - a few misc fixups

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each"
  mm/early_ioremap: add explicit #include of asm/early_ioremap.h
  fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void
  selftests: enhance membarrier syscall test
  selftests: add membarrier syscall test
  sys_membarrier(): system-wide memory barrier (generic, x86)
  MODSIGN: fix a compilation warning in extract-cert

ARCv2: [axs103_smp] Reduce clk for SMP FPGA configs

Newer bitfiles needs the reduced clk even for SMP builds

Cc: <stable@vger.kernel.org> #4.2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'ntb-4.3' of git://github.com/jonmason/ntb

Pull NTB fixes from Jon Mason:
 "NTB bug and documentation fixes, new device IDs, performance
  improvements, and adding a mailing list to MAINTAINERS for NTB"

* tag 'ntb-4.3' of git://github.com/jonmason/ntb:
  NTB: Fix range check on memory window index
  NTB: Improve index handling in B2B MW workaround
  NTB: Fix documentation for ntb_peer_db_clear.
  NTB: Fix documentation for ntb_link_is_up
  NTB: Use unique DMA channels for TX and RX
  NTB: Remove dma_sync_wait from ntb_async_rx
  NTB: Clean up QP stats info
  NTB: Make the transport list in order of discovery
  NTB: Add PCI Device IDs for Broadwell Xeon
  NTB: Add flow control to the ntb_netdev
  NTB: Add list to MAINTAINERS

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull more input updates from Dmitry Torokhov:
 "Second round of updates for the input subsystem.

  This introduces two brand new touchscreen drivers (Colibri and
  imx6ul_tsc), some small driver fixes, and we are no longer report
  errors from evdev_flush() as users do not really have a way of
  handling errors, error codes that we were returning were not on the
  list of errors supposed to be returned by close(), and errors were
  causing issues with one of older versions of systemd"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: imx_keypad - remove obsolete comment
  Input: touchscreen - add imx6ul_tsc driver support
  Input: Add touchscreen support for Colibri VF50
  Input: i8042 - lower log level for "no controller" message
  Input: evdev - do not report errors form flush()
  Input: elants_i2c - extend the calibration timeout to 12 seconds
  Input: sparcspkr - fix module autoload for OF platform drivers
  Input: regulator-haptic - fix module autoload for OF platform driver
  Input: pwm-beeper - fix module autoload for OF platform driver
  Input: ab8500-ponkey - Fix module autoload for OF platform driver
  Input: cyttsp - remove unnecessary MODULE_ALIAS()
  Input: elan_i2c - add ACPI ID "ELAN1000"

Merge tag 'pm+acpi-4.3-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm

Pull more power management and ACPI updates from Rafael Wysocki:
 "These are mostly fixes and cleanups on top of the previous PM+ACPI
  pull request (cpufreq core and drivers, cpuidle, generic power domains
  framework).  Some of them didn't make to that pull request and some
  fix issues introduced by it.

  The only really new thing is the support for suspend frequency in the
  cpufreq-dt driver, but it is needed to fix an issue with Exynos
  platforms.

  Specifics:

   - build fix for the new Mediatek MT8173 cpufreq driver (Guenter
     Roeck).

   - generic power domains framework fixes (power on error code path,
     subdomain removal) and cleanup of a deprecated API user (Geert
     Uytterhoeven, Jon Hunter, Ulf Hansson).

   - cpufreq-dt driver fixes including two fixes for bugs related to the
     new Operating Performance Points Device Tree bindings introduced
     recently (Viresh Kumar).

   - suspend frequency support for the cpufreq-dt driver (Bartlomiej
     Zolnierkiewicz, Viresh Kumar).

   - cpufreq core cleanups (Viresh Kumar).

   - intel_pstate driver fixes (Chen Yu, Kristen Carlson Accardi).

   - additional sanity check in the cpuidle core (Xunlei Pang).

   - fix for a comment related to CPU power management (Lina Iyer)"

* tag 'pm+acpi-4.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  intel_pstate: fix PCT_TO_HWP macro
  intel_pstate: Fix user input of min/max to legal policy region
  PM / OPP: Return suspend_opp only if it is enabled
  cpufreq-dt: add suspend frequency support
  cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency
  PM / OPP: add dev_pm_opp_get_suspend_opp() helper
  staging: board: Migrate away from __pm_genpd_name_add_device()
  cpufreq: Use __func__ to print function's name
  cpufreq: staticize cpufreq_cpu_get_raw()
  PM / Domains: Ensure subdomain is not in use before removing
  cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL
  cpuidle/coupled: Add sanity check for safe_state_index
  PM / Domains: Try power off masters in error path of __pm_genpd_poweron()
  cpufreq: dt: Tolerance applies on both sides of target voltage
  cpufreq: dt: Print error on failing to mark OPPs as shared
  cpufreq: dt: Check OPP count before marking them shared
  kernel/cpu_pm: fix cpu_cluster_pm_exit comment

Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending

Pull SCSI target updates from Nicholas Bellinger:
 "Here are the outstanding target-pending updates for v4.3-rc1.

  Mostly bug-fixes and minor changes this round.  The fallout from the
  big v4.2-rc1 RCU conversion have (thus far) been minimal.

  The highlights this round include:

   - Move sense handling routines into scsi_common code (Sagi)

   - Return ABORTED_COMMAND sense key for PI errors (Sagi)

   - Add tpg_enabled_sendtargets attribute for disabled iscsi-target
     discovery (David)

   - Shrink target struct se_cmd by rearranging fields (Roland)

   - Drop iSCSI use of mutex around max_cmd_sn increment (Roland)

   - Replace iSCSI __kernel_sockaddr_storage with sockaddr_storage (Andy +
     Chris)

   - Honor fabric max_data_sg_nents I/O transfer limit (Arun + Himanshu +
     nab)

   - Fix EXTENDED_COPY >= v4.1 regression OOPsen (Alex + nab)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (37 commits)
  target: use stringify.h instead of own definition
  target/user: Fix UFLAG_UNKNOWN_OP handling
  target: Remove no-op conditional
  target/user: Remove unused variable
  target: Fix max_cmd_sn increment w/o cmdsn mutex regressions
  target: Attach EXTENDED_COPY local I/O descriptors to xcopy_pt_sess
  target/qla2xxx: Honor max_data_sg_nents I/O transfer limit
  target/iscsi: Replace __kernel_sockaddr_storage with sockaddr_storage
  target/iscsi: Replace conn->login_ip with login_sockaddr
  target/iscsi: Keep local_ip as the actual sockaddr
  target/iscsi: Fix np_ip bracket issue by removing np_ip
  target: Drop iSCSI use of mutex around max_cmd_sn increment
  qla2xxx: Update tcm_qla2xxx module description to 24xx+
  iscsi-target: Add tpg_enabled_sendtargets for disabled discovery
  drivers: target: Drop unlikely before IS_ERR(_OR_NULL)
  target: check DPO/FUA usage for COMPARE AND WRITE
  target: Shrink struct se_cmd by rearranging fields
  target: Remove cmd->se_ordered_id (unused except debug log lines)
  target: add support for START_STOP_UNIT SCSI opcode
  target: improve unsupported opcode message
  ...

Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi

Pull second round of SCSI updates from James Bottomley:
 "There's one late arriving patch here (added today), fixing a build
  issue which the scsi_dh patch set in here uncovered.  Other than that,
  everything has been incubated in -next and the checkers for a week.

  The major pieces of this patch are a set patches facilitating better
  integration between scsi and scsi_dh (the device handling layer used
  by multi-path; all the dm parts are acked by Mike Snitzer).

  This also includes driver updates for mp3sas, scsi_debug and an
  assortment of bug fixes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (50 commits)
  scsi_dh: fix randconfig build error
  scsi: fix scsi_error_handler vs. scsi_host_dev_release race
  fcoe: Convert use of __constant_htons to htons
  mpt2sas: setpci reset kernel oops fix
  pm80xx: Don't override ts->stat on IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY
  lpfc: Fix possible use-after-free and double free in lpfc_mbx_cmpl_rdp_page_a2()
  bfa: Fix incorrect de-reference of pointer
  bfa: Fix indentation
  scsi_transport_sas: Remove check for SAS expander when querying bay/enclosure IDs.
  scsi_debug: resp_request: remove unused variable
  scsi_debug: fix REPORT LUNS Well Known LU
  scsi_debug: schedule_resp fix input variable check
  scsi_debug: make dump_sector static
  scsi_debug: vfree is null safe so drop the check
  scsi_debug: use SCSI_W_LUN_REPORT_LUNS instead of SAM2_WLUN_REPORT_LUNS;
  scsi_debug: define pr_fmt() for consistent logging
  mpt2sas: Refcount fw_events and fix unsafe list usage
  mpt2sas: Refcount sas_device objects and fix unsafe list usage
  scsi_dh: return SCSI_DH_NOTCONN in scsi_dh_activate()
  scsi_dh: don't allow to detach device handlers at runtime
  ...

Merge tag 'media/v4.3-2' of git://git./linux/kernel/git/mchehab/linux-media

Pull media updates from Mauro Carvalho Chehab:
 "A series of patches that move part of the code used to allocate memory
  from the media subsystem to the mm subsystem"

[ The mm parts have been acked by VM people, and the series was
  apparently in -mm for a while   - Linus ]

* tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] drm/exynos: Convert g2d_userptr_get_dma_addr() to use get_vaddr_frames()
  [media] media: vb2: Remove unused functions
  [media] media: vb2: Convert vb2_dc_get_userptr() to use frame vector
  [media] media: vb2: Convert vb2_vmalloc_get_userptr() to use frame vector
  [media] media: vb2: Convert vb2_dma_sg_get_userptr() to use frame vector
  [media] vb2: Provide helpers for mapping virtual addresses
  [media] media: omap_vout: Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns()
  [media] mm: Provide new get_vaddr_frames() helper
  [media] vb2: Push mmap_sem down to memops

Merge tag 'edac/v4.3-1' of git://git./linux/kernel/git/mchehab/linux-edac

Pull edac updates from Mauro Carvalho Chehab:
 "Two EDAC fixes for Intel systems (Haswell and Ivy Bridge)"

* tag 'edac/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
  sb_edac: correctly fetch DIMM width on Ivy Bridge and Haswell
  sb_edac: look harder for DDRIO on Haswell systems

Merge branch 'next' of git://git./linux/kernel/git/rzhang/linux

Pull thermal updates from Zhang Rui:

 - use int instead of unsigned long to represent temperature to avoid
   bogus overheat detection when negative temperature reported.  From
   Sascha Hauer.

 - export available thermal governors information to user space via
   sysfs.  From Wei Ni.

 - introduce new thermal driver for Wildcat Point platform controller
   hub, which uses PCH thermal sensor and associated critical and hot
   trip points.  From Tushar Dave.

 - add suuport for Intel Skylake and Denlow platforms in powerclamp
   driver.

 - some small cleanups in thermal core.

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: Add Intel PCH thermal driver
  thermal: Add comment explaining test for critical temperature
  thermal: Use IS_ENABLED instead of #ifdef
  thermal: remove unnecessary call to thermal_zone_device_set_polling
  thermal: trivial: fix typo in comment
  thermal: consistently use int for temperatures
  thermal: add available policies sysfs attribute
  thermal/powerclamp: add cpu id for denlow platform
  thermal/powerclamp: add cpu id for Skylake u/y
  thermal/powerclamp: add cpu id for skylake h/s

revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each"

Revert commit f83c7b5e9fd6 ("ocfs2/dlm: use list_for_each_entry instead
of list_for_each").

list_for_each_entry() will dereference its `pos' argument, which can be
NULL in dlm_process_recovery_data().

Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: Fengguang Wu <fengguang.wu@gmail.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/early_ioremap: add explicit #include of asm/early_ioremap.h

Commit 6b0f68e32ea8 ("mm: add utility for early copy from unmapped ram")
introduces a function copy_from_early_mem() into mm/early_ioremap.c
which itself calls early_memremap()/early_memunmap().  However, since
early_memunmap() has not been declared yet at this point in the .c file,
nor by any explicitly included header files, we are depending on a
transitive include of asm/early_ioremap.h to declare it, which is
fragile.

So instead, include this header explicitly.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void

The seq_<foo> function return values were frequently misused.

See: commit 1f33c41c03da ("seq_file: Rename seq_overflow() to
     seq_has_overflowed() and make public")

All uses of these return values have been removed, so convert the
return types to void.

Miscellanea:

o Move seq_put_decimal_<type> and seq_escape prototypes closer the
  other seq_vprintf prototypes
o Reorder seq_putc and seq_puts to return early on overflow
o Add argument names to seq_vprintf and seq_printf
o Update the seq_escape kernel-doc
o Convert a couple of leading spaces to tabs in seq_escape

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

selftests: enhance membarrier syscall test

Update the membarrier syscall self-test to match the membarrier
interface.  Extend coverage of the interface.  Consider ENOSYS as a
"SKIP" test, since it is a valid configuration, but does not allow
testing the system call.

Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Pranith Kumar <bobby.prani@gmail.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>