git.monstr.eu Git - linux-2.6-microblaze.git/log

Merge tag 'sound-5.18-rc4' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"At this time, the majority of changes are for pending ASoC fixes while
  a few usual HD-audio and USB-audio quirks are found.

  Almost all patches are small device-specific fixes, and nothing
  worrisome stands out, so far"

* tag 'sound-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (37 commits)
  ALSA: hda/realtek: Add quirk for Clevo NP70PNP
  ALSA: hda: intel-dsp-config: Add RaptorLake PCI IDs
  ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on EliteBook 845/865 G9
  ALSA: usb-audio: Clear MIDI port active flag after draining
  ALSA: usb-audio: add mapping for MSI MAG X570S Torpedo MAX.
  ALSA: hda/i915: Fix one too many pci_dev_put()
  ALSA: hda/hdmi: add HDMI codec VID for Raptorlake-P
  ALSA: hda/hdmi: fix warning about PCM count when used with SOF
  sound/oss/dmasound: fix 'dmasound_setup' defined but not used
  firmware: cs_dsp: Fix overrun of unterminated control name string
  ASoC: codecs: Fix an error handling path in (rx|tx|va)_macro_probe()
  ASoC: Intel: sof_es8336: Add a quirk for Huawei Matebook D15
  ASoC: Intel: sof_es8336: add a quirk for headset at mic1 port
  ASoC: Intel: sof_es8336: support a separate gpio to control headphone
  ASoC: Intel: sof_es8336: simplify speaker gpio naming
  ASoC: wm8731: Disable the regulator when probing fails
  ASoC: Intel: soc-acpi: correct device endpoints for max98373
  ASoC: codecs: wcd934x: do not switch off SIDO Buck when codec is in use
  ASoC: SOF: topology: Fix memory leak in sof_control_load()
  ASoC: SOF: topology: cleanup dailinks on widget unload
  ...

Merge branch 'akpm' (patches from Andrew)

Merge misc fixes from Andrew Morton:
"13 patches.

  Subsystems affected by this patch series: mm (memory-failure, memcg,
  userfaultfd, hugetlbfs, mremap, oom-kill, kasan, hmm), and kcov"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm/mmu_notifier.c: fix race in mmu_interval_notifier_remove()
  kcov: don't generate a warning on vm_insert_page()'s failure
  MAINTAINERS: add Vincenzo Frascino to KASAN reviewers
  oom_kill.c: futex: delay the OOM reaper to allow time for proper futex cleanup
  selftest/vm: add skip support to mremap_test
  selftest/vm: support xfail in mremap_test
  selftest/vm: verify remap destination address in mremap_test
  selftest/vm: verify mmap addr in mremap_test
  mm, hugetlb: allow for "high" userspace addresses
  userfaultfd: mark uffd_wp regardless of VM_WRITE flag
  memcg: sync flush only if periodic flush is delayed
  mm/memory-failure.c: skip huge_zero_page in memory_failure()
  mm/hwpoison: fix race between hugetlb free/demotion and memory_failure_hugetlb()

mm/vmalloc: huge vmalloc backing pages should be split rather than compound

Huge vmalloc higher-order backing pages were allocated with __GFP_COMP
in order to allow the sub-pages to be refcounted by callers such as
"remap_vmalloc_page [sic]" (remap_vmalloc_range).

However a similar problem exists for other struct page fields callers
use, for example fb_deferred_io_fault() takes a vmalloc'ed page and
not only refcounts it but uses ->lru, ->mapping, ->index.

This is not compatible with compound sub-pages, and can cause bad page
state issues like

  BUG: Bad page state in process swapper/0  pfn:00743
  page:(____ptrval____) refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x743
  flags: 0x7ffff000000000(node=0|zone=0|lastcpupid=0x7ffff)
  raw: 007ffff000000000 c00c00000001d0c8 c00c00000001d0c8 0000000000000000
  raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
  page dumped because: corrupted mapping in tail page
  Modules linked in:
  CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.18.0-rc3-00082-gfc6fff4a7ce1-dirty #2810
  Call Trace:
    dump_stack_lvl+0x74/0xa8 (unreliable)
    bad_page+0x12c/0x170
    free_tail_pages_check+0xe8/0x190
    free_pcp_prepare+0x31c/0x4e0
    free_unref_page+0x40/0x1b0
    __vunmap+0x1d8/0x420
    ...

The correct approach is to use split high-order pages for the huge
vmalloc backing. These allow callers to treat them in exactly the same
way as individually-allocated order-0 pages.

Link: https://lore.kernel.org/all/14444103-d51b-0fb3-ee63-c3f182f0b546@molgen.mpg.de/
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: Song Liu <songliubraving@fb.com>
Cc: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'drm-fixes-2022-04-22' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
"Extra quiet after Easter, only have minor i915 and msm pulls. However
  I haven't seen a PR from our misc tree in a little while, I've cc'ed
  all the suspects. Once that unblocks I expect a bit larger bunch of
  patches to arrive.

  Otherwise as I said, one msm revert and two i915 fixes.

  msm:

   - revert iommu change that broke some platforms.

  i915:

   - Unset enable_psr2_sel_fetch if PSR2 detection fails

   - Fix to detect when VRR is turned off from panel settings"

* tag 'drm-fixes-2022-04-22' of git://anongit.freedesktop.org/drm/drm:
  drm/i915/display/psr: Unset enable_psr2_sel_fetch if other checks in intel_psr2_config_valid() fails
  drm/msm: Revert "drm/msm: Stop using iommu_present()"
  drm/i915/display/vrr: Reset VRR capable property on a long hpd

mm/mmu_notifier.c: fix race in mmu_interval_notifier_remove()

In some cases it is possible for mmu_interval_notifier_remove() to race
with mn_tree_inv_end() allowing it to return while the notifier data
structure is still in use.  Consider the following sequence:

  CPU0 - mn_tree_inv_end()            CPU1 - mmu_interval_notifier_remove()
  ----------------------------------- ------------------------------------
                                      spin_lock(subscriptions->lock);
                                      seq = subscriptions->invalidate_seq;
  spin_lock(subscriptions->lock);     spin_unlock(subscriptions->lock);
  subscriptions->invalidate_seq++;
                                      wait_event(invalidate_seq != seq);
                                      return;
  interval_tree_remove(interval_sub); kfree(interval_sub);
  spin_unlock(subscriptions->lock);
  wake_up_all();

As the wait_event() condition is true it will return immediately.  This
can lead to use-after-free type errors if the caller frees the data
structure containing the interval notifier subscription while it is
still on a deferred list.  Fix this by taking the appropriate lock when
reading invalidate_seq to ensure proper synchronisation.

I observed this whilst running stress testing during some development.
You do have to be pretty unlucky, but it leads to the usual problems of
use-after-free (memory corruption, kernel crash, difficult to diagnose
WARN_ON, etc).

Link: https://lkml.kernel.org/r/20220420043734.476348-1-apopple@nvidia.com
Fixes: 99cb252f5e68 ("mm/mmu_notifier: add an interval tree notifier")
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kcov: don't generate a warning on vm_insert_page()'s failure

vm_insert_page()'s failure is not an unexpected condition, so don't do
WARN_ONCE() in such a case.

Instead, print a kernel message and just return an error code.

This flaw has been reported under an OOM condition by sysbot [1].

The message is mainly for the benefit of the test log, in this case the
fuzzer's log so that humans inspecting the log can figure out what was
going on. KCOV is a testing tool, so I think being a little more chatty
when KCOV unexpectedly is about to fail will save someone debugging
time.

We don't want the WARN, because it's not a kernel bug that syzbot should
report, and failure can happen if the fuzzer tries hard enough (as
above).

Link: https://lkml.kernel.org/r/Ylkr2xrVbhQYwNLf@elver.google.com
Link: https://lkml.kernel.org/r/20220401182512.249282-1-nogikh@google.com
Fixes: b3d7fe86fbd0 ("kcov: properly handle subsequent mmap calls"),
Signed-off-by: Aleksandr Nogikh <nogikh@google.com>
Acked-by: Marco Elver <elver@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Taras Madan <tarasmadan@google.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: add Vincenzo Frascino to KASAN reviewers

Add my email address to KASAN reviewers list to make sure that I am
Cc'ed in all the KASAN changes that may affect arm64 MTE.

Link: https://lkml.kernel.org/r/20220419170640.21404-1-vincenzo.frascino@arm.com
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

oom_kill.c: futex: delay the OOM reaper to allow time for proper futex cleanup

The pthread struct is allocated on PRIVATE|ANONYMOUS memory [1] which
can be targeted by the oom reaper.  This mapping is used to store the
futex robust list head; the kernel does not keep a copy of the robust
list and instead references a userspace address to maintain the
robustness during a process death.

A race can occur between exit_mm and the oom reaper that allows the oom
reaper to free the memory of the futex robust list before the exit path
has handled the futex death:

    CPU1                               CPU2
    --------------------------------------------------------------------
    page_fault
    do_exit "signal"
    wake_oom_reaper
                                        oom_reaper
                                        oom_reap_task_mm (invalidates mm)
    exit_mm
    exit_mm_release
    futex_exit_release
    futex_cleanup
    exit_robust_list
    get_user (EFAULT- can't access memory)

If the get_user EFAULT's, the kernel will be unable to recover the
waiters on the robust_list, leaving userspace mutexes hung indefinitely.

Delay the OOM reaper, allowing more time for the exit path to perform
the futex cleanup.

Reproducer: https://gitlab.com/jsavitz/oom_futex_reproducer

Based on a patch by Michal Hocko.

Link: https://elixir.bootlin.com/glibc/glibc-2.35/source/nptl/allocatestack.c#L370
Link: https://lkml.kernel.org/r/20220414144042.677008-1-npache@redhat.com
Fixes: 212925802454 ("mm: oom: let oom_reap_task and exit_mmap run concurrently")
Signed-off-by: Joel Savitz <jsavitz@redhat.com>
Signed-off-by: Nico Pache <npache@redhat.com>
Co-developed-by: Joel Savitz <jsavitz@redhat.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Waiman Long <longman@redhat.com>
Cc: Herton R. Krzesinski <herton@redhat.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joel Savitz <jsavitz@redhat.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

selftest/vm: add skip support to mremap_test

Allow the mremap test to be skipped due to errors such as failing to
parse the mmap_min_addr sysctl.

Link: https://lkml.kernel.org/r/20220420215721.4868-4-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

selftest/vm: support xfail in mremap_test

Use ksft_test_result_xfail for the tests which are expected to fail.

Link: https://lkml.kernel.org/r/20220420215721.4868-3-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

selftest/vm: verify remap destination address in mremap_test

Because mremap does not have a MAP_FIXED_NOREPLACE flag, it can destroy
existing mappings. This causes a segfault when regions such as text are
remapped and the permissions are changed.

Verify the requested mremap destination address does not overlap any
existing mappings by using mmap's MAP_FIXED_NOREPLACE flag. Keep
incrementing the destination address until a valid mapping is found or
fail the current test once the max address is reached.

Link: https://lkml.kernel.org/r/20220420215721.4868-2-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

selftest/vm: verify mmap addr in mremap_test

Avoid calling mmap with requested addresses that are less than the
system's mmap_min_addr. When run as root, mmap returns EACCES when
trying to map addresses < mmap_min_addr. This is not one of the error
codes for the condition to retry the mmap in the test.

Rather than arbitrarily retrying on EACCES, don't attempt an mmap until
addr > vm.mmap_min_addr.

Add a munmap call after an alignment check as the mappings are retained
after the retry and can reach the vm.max_map_count sysctl.

Link: https://lkml.kernel.org/r/20220420215721.4868-1-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, hugetlb: allow for "high" userspace addresses

This is a fix for commit f6795053dac8 ("mm: mmap: Allow for "high"
userspace addresses") for hugetlb.

This patch adds support for "high" userspace addresses that are
optionally supported on the system and have to be requested via a hint
mechanism ("high" addr parameter to mmap).

Architectures such as powerpc and x86 achieve this by making changes to
their architectural versions of hugetlb_get_unmapped_area() function.
However, arm64 uses the generic version of that function.

So take into account arch_get_mmap_base() and arch_get_mmap_end() in
hugetlb_get_unmapped_area().  To allow that, move those two macros out
of mm/mmap.c into include/linux/sched/mm.h

If these macros are not defined in architectural code then they default
to (TASK_SIZE) and (base) so should not introduce any behavioural
changes to architectures that do not define them.

For the time being, only ARM64 is affected by this change.

Catalin (ARM64) said
"We should have fixed hugetlb_get_unmapped_area() as well when we added
  support for 52-bit VA. The reason for commit f6795053dac8 was to
  prevent normal mmap() from returning addresses above 48-bit by default
  as some user-space had hard assumptions about this.

  It's a slight ABI change if you do this for hugetlb_get_unmapped_area()
  but I doubt anyone would notice. It's more likely that the current
  behaviour would cause issues, so I'd rather have them consistent.

  Basically when arm64 gained support for 52-bit addresses we did not
  want user-space calling mmap() to suddenly get such high addresses,
  otherwise we could have inadvertently broken some programs (similar
  behaviour to x86 here). Hence we added commit f6795053dac8. But we
  missed hugetlbfs which could still get such high mmap() addresses. So
  in theory that's a potential regression that should have bee addressed
  at the same time as commit f6795053dac8 (and before arm64 enabled
  52-bit addresses)"

Link: https://lkml.kernel.org/r/ab847b6edb197bffdfe189e70fb4ac76bfe79e0d.1650033747.git.christophe.leroy@csgroup.eu
Fixes: f6795053dac8 ("mm: mmap: Allow for "high" userspace addresses")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> [5.0.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

userfaultfd: mark uffd_wp regardless of VM_WRITE flag

When a PTE is set by UFFD operations such as UFFDIO_COPY, the PTE is
currently only marked as write-protected if the VMA has VM_WRITE flag
set. This seems incorrect or at least would be unexpected by the users.

Consider the following sequence of operations that are being performed
on a certain page:

mprotect(PROT_READ)
UFFDIO_COPY(UFFDIO_COPY_MODE_WP)
mprotect(PROT_READ|PROT_WRITE)

At this point the user would expect to still get UFFD notification when
the page is accessed for write, but the user would not get one, since
the PTE was not marked as UFFD_WP during UFFDIO_COPY.

Fix it by always marking PTEs as UFFD_WP regardless on the
write-permission in the VMA flags.

Link: https://lkml.kernel.org/r/20220217211602.2769-1-namit@vmware.com
Fixes: 292924b26024 ("userfaultfd: wp: apply _PAGE_UFFD_WP bit")
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: sync flush only if periodic flush is delayed

Daniel Dao has reported [1] a regression on workloads that may trigger a
lot of refaults (anon and file).  The underlying issue is that flushing
rstat is expensive.  Although rstat flush are batched with (nr_cpus *
MEMCG_BATCH) stat updates, it seems like there are workloads which
genuinely do stat updates larger than batch value within short amount of
time.  Since the rstat flush can happen in the performance critical
codepaths like page faults, such workload can suffer greatly.

This patch fixes this regression by making the rstat flushing
conditional in the performance critical codepaths.  More specifically,
the kernel relies on the async periodic rstat flusher to flush the stats
and only if the periodic flusher is delayed by more than twice the
amount of its normal time window then the kernel allows rstat flushing
from the performance critical codepaths.

Now the question: what are the side-effects of this change? The worst
that can happen is the refault codepath will see 4sec old lruvec stats
and may cause false (or missed) activations of the refaulted page which
may under-or-overestimate the workingset size.  Though that is not very
concerning as the kernel can already miss or do false activations.

There are two more codepaths whose flushing behavior is not changed by
this patch and we may need to come to them in future.  One is the
writeback stats used by dirty throttling and second is the deactivation
heuristic in the reclaim.  For now keeping an eye on them and if there
is report of regression due to these codepaths, we will reevaluate then.

Link: https://lore.kernel.org/all/CA+wXwBSyO87ZX5PVwdHm-=dBjZYECGmfnydUicUyrQqndgX2MQ@mail.gmail.com
Link: https://lkml.kernel.org/r/20220304184040.1304781-1-shakeelb@google.com
Fixes: 1f828223b799 ("memcg: flush lruvec stats in the refault")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reported-by: Daniel Dao <dqminh@cloudflare.com>
Tested-by: Ivan Babrou <ivan@cloudflare.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Koutný <mkoutny@suse.com>
Cc: Frank Hofmann <fhofmann@cloudflare.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/memory-failure.c: skip huge_zero_page in memory_failure()

Kernel panic when injecting memory_failure for the global
huge_zero_page, when CONFIG_DEBUG_VM is enabled, as follows.

  Injecting memory failure for pfn 0x109ff9 at process virtual address 0x20ff9000
  page:00000000fb053fc3 refcount:2 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x109e00
  head:00000000fb053fc3 order:9 compound_mapcount:0 compound_pincount:0
  flags: 0x17fffc000010001(locked|head|node=0|zone=2|lastcpupid=0x1ffff)
  raw: 017fffc000010001 0000000000000000 dead000000000122 0000000000000000
  raw: 0000000000000000 0000000000000000 00000002ffffffff 0000000000000000
  page dumped because: VM_BUG_ON_PAGE(is_huge_zero_page(head))
  ------------[ cut here ]------------
  kernel BUG at mm/huge_memory.c:2499!
  invalid opcode: 0000 [#1] PREEMPT SMP PTI
  CPU: 6 PID: 553 Comm: split_bug Not tainted 5.18.0-rc1+ #11
  Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 3288b3c 04/01/2014
  RIP: 0010:split_huge_page_to_list+0x66a/0x880
  Code: 84 9b fb ff ff 48 8b 7c 24 08 31 f6 e8 9f 5d 2a 00 b8 b8 02 00 00 e9 e8 fb ff ff 48 c7 c6 e8 47 3c 82 4c b
  RSP: 0018:ffffc90000dcbdf8 EFLAGS: 00010246
  RAX: 000000000000003c RBX: 0000000000000001 RCX: 0000000000000000
  RDX: 0000000000000000 RSI: ffffffff823e4c4f RDI: 00000000ffffffff
  RBP: ffff88843fffdb40 R08: 0000000000000000 R09: 00000000fffeffff
  R10: ffffc90000dcbc48 R11: ffffffff82d68448 R12: ffffea0004278000
  R13: ffffffff823c6203 R14: 0000000000109ff9 R15: ffffea000427fe40
  FS:  00007fc375a26740(0000) GS:ffff88842fd80000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007fc3757c9290 CR3: 0000000102174006 CR4: 00000000003706e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   try_to_split_thp_page+0x3a/0x130
   memory_failure+0x128/0x800
   madvise_inject_error.cold+0x8b/0xa1
   __x64_sys_madvise+0x54/0x60
   do_syscall_64+0x35/0x80
   entry_SYSCALL_64_after_hwframe+0x44/0xae
  RIP: 0033:0x7fc3754f8bf9
  Code: 01 00 48 81 c4 80 00 00 00 e9 f1 fe ff ff 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 8
  RSP: 002b:00007ffeda93a1d8 EFLAGS: 00000217 ORIG_RAX: 000000000000001c
  RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fc3754f8bf9
  RDX: 0000000000000064 RSI: 0000000000003000 RDI: 0000000020ff9000
  RBP: 00007ffeda93a200 R08: 0000000000000000 R09: 0000000000000000
  R10: 00000000ffffffff R11: 0000000000000217 R12: 0000000000400490
  R13: 00007ffeda93a2e0 R14: 0000000000000000 R15: 0000000000000000

This makes huge_zero_page bail out explicitly before split in
memory_failure(), thus the panic above won't happen again.

Link: https://lkml.kernel.org/r/497d3835612610e370c74e697ea3c721d1d55b9c.1649775850.git.xuyu@linux.alibaba.com
Fixes: 6a46079cf57a ("HWPOISON: The high level memory error handler in the VM v7")
Signed-off-by: Xu Yu <xuyu@linux.alibaba.com>
Reported-by: Abaci <abaci@linux.alibaba.com>
Suggested-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/hwpoison: fix race between hugetlb free/demotion and memory_failure_hugetlb()

There is a race condition between memory_failure_hugetlb() and hugetlb
free/demotion, which causes setting PageHWPoison flag on the wrong page.
The one simple result is that wrong processes can be killed, but another
(more serious) one is that the actual error is left unhandled, so no one
prevents later access to it, and that might lead to more serious results
like consuming corrupted data.

Think about the below race window:

  CPU 1                                   CPU 2
  memory_failure_hugetlb
  struct page *head = compound_head(p);
                                          hugetlb page might be freed to
                                          buddy, or even changed to another
                                          compound page.

  get_hwpoison_page -- page is not what we want now...

The current code first does prechecks roughly and then reconfirms after
taking refcount, but it's found that it makes code overly complicated,
so move the prechecks in a single hugetlb_lock range.

A newly introduced function, try_memory_failure_hugetlb(), always takes
hugetlb_lock (even for non-hugetlb pages).  That can be improved, but
memory_failure() is rare in principle, so should not be a big problem.

Link: https://lkml.kernel.org/r/20220408135323.1559401-2-naoya.horiguchi@linux.dev
Fixes: 761ad8d7c7b5 ("mm: hwpoison: introduce memory_failure_hugetlb()")
Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Reported-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'drm-msm-fixes-2022-04-20' of https://gitlab.freedesktop.org/drm/msm into drm-fixes

Revert to fix iommu regression.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtvPo4xD2peAztDMPP2n4utb7d9WQboMFwsba9E8U2rCw@mail.gmail.com

Merge tag 'dmaengine-fix-5.18' of git://git./linux/kernel/git/vkoul/dmaengine

Pull dmaengine fixes from Vinod Koul:
"A bunch of driver fixes:

   - idxd device RO checks and device cleanup

   - dw-edma unaligned access and alignment

   - qcom: missing minItems in binding

   - mediatek pm usage fix

   - imx init script"

* tag 'dmaengine-fix-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
  dt-bindings: dmaengine: qcom: gpi: Add minItems for interrupts
  dmaengine: idxd: skip clearing device context when device is read-only
  dmaengine: idxd: add RO check for wq max_transfer_size write
  dmaengine: idxd: add RO check for wq max_batch_size write
  dmaengine: idxd: fix retry value to be constant for duration of function call
  dmaengine: idxd: match type for retries var in idxd_enqcmds()
  dmaengine: dw-edma: Fix inconsistent indenting
  dmaengine: dw-edma: Fix unaligned 64bit access
  dmaengine: mediatek:Fix PM usage reference leak of mtk_uart_apdma_alloc_chan_resources
  dmaengine: imx-sdma: Fix error checking in sdma_event_remap
  dma: at_xdmac: fix a missing check on list iterator
  dmaengine: imx-sdma: fix init of uart scripts
  dmaengine: idxd: fix device cleanup on disable

Merge tag 'drm-intel-fixes-2022-04-20' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

- Unset enable_psr2_sel_fetch if PSR2 detection fails
- Fix to detect when VRR is turned off from panel settings

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YmAKuHwon7hGyIoC@jlahtine-mobl.ger.corp.intel.com

Merge tag 'net-5.18-rc4' of git://git./linux/kernel/git/netdev/net

Pull networking fixes from Paolo Abeni:
"Including fixes from xfrm and can.

  Current release - regressions:

   - rxrpc: restore removed timer deletion

  Current release - new code bugs:

   - gre: fix device lookup for l3mdev use-case

   - xfrm: fix egress device lookup for l3mdev use-case

  Previous releases - regressions:

   - sched: cls_u32: fix netns refcount changes in u32_change()

   - smc: fix sock leak when release after smc_shutdown()

   - xfrm: limit skb_page_frag_refill use to a single page

   - eth: atlantic: invert deep par in pm functions, preventing null
     derefs

   - eth: stmmac: use readl_poll_timeout_atomic() in atomic state

  Previous releases - always broken:

   - gre: fix skb_under_panic on xmit

   - openvswitch: fix OOB access in reserve_sfa_size()

   - dsa: hellcreek: calculate checksums in tagger

   - eth: ice: fix crash in switchdev mode

   - eth: igc:
      - fix infinite loop in release_swfw_sync
      - fix scheduling while atomic"

* tag 'net-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
  drivers: net: hippi: Fix deadlock in rr_close()
  selftests: mlxsw: vxlan_flooding_ipv6: Prevent flooding of unwanted packets
  selftests: mlxsw: vxlan_flooding: Prevent flooding of unwanted packets
  nfc: MAINTAINERS: add Bug entry
  net: stmmac: Use readl_poll_timeout_atomic() in atomic state
  doc/ip-sysctl: add bc_forwarding
  netlink: reset network and mac headers in netlink_dump()
  net: mscc: ocelot: fix broken IP multicast flooding
  net: dsa: hellcreek: Calculate checksums in tagger
  net: atlantic: invert deep par in pm functions, preventing null derefs
  can: isotp: stop timeout monitoring when no first frame was sent
  bonding: do not discard lowest hash bit for non layer3+4 hashing
  net: lan966x: Make sure to release ptp interrupt
  ipv6: make ip6_rt_gc_expire an atomic_t
  net: Handle l3mdev in ip_tunnel_init_flow
  l3mdev: l3mdev_master_upper_ifindex_by_index_rcu should be using netdev_master_upper_dev_get_rcu
  net/sched: cls_u32: fix possible leak in u32_init_knode()
  net/sched: cls_u32: fix netns refcount changes in u32_change()
  powerpc: Update MAINTAINERS for ibmvnic and VAS
  net: restore alpha order to Ethernet devices in config
  ...

ALSA: hda/realtek: Add quirk for Clevo NP70PNP

Fixes headset detection on Clevo NP70PNP.

Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220421170412.3697-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda: intel-dsp-config: Add RaptorLake PCI IDs

Add RaptorLake-P PCI IDs

Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220421163546.319604-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

drivers: net: hippi: Fix deadlock in rr_close()

There is a deadlock in rr_close(), which is shown below:

   (Thread 1)                |      (Thread 2)
                             | rr_open()
rr_close()                   |  add_timer()
spin_lock_irqsave() //(1)   |  (wait a time)
...                         | rr_timer()
del_timer_sync()            |  spin_lock_irqsave() //(2)
(wait timer to stop)        |  ...

We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.

This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.

Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417125519.82618-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on EliteBook 845/865 G9

On HP EliteBook 845 G9 and EliteBook 865 G9, the audio LEDs can be enabled by
ALC285_FIXUP_HP_MUTE_LED. So use it accordingly.

Signed-off-by: Andy Chi <andy.chi@canonical.com>
Fixes: 07bcab93946c ("ALSA: hda/realtek: Add support for HP Laptops")
Link: https://lore.kernel.org/r/20220421063606.39772-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'xtensa-20220416' of https://github.com/jcmvbkbc/linux-xtensa

Pull xtensa fixes from Max Filippov:

- fix patching CPU selection in patch_text

- fix potential deadlock in ISS platform serial driver

- fix potential register clobbering in coprocessor exception handler

* tag 'xtensa-20220416' of https://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix a7 clobbering in coprocessor context load/store
  arch: xtensa: platforms: Fix deadlock in rs_close()
  xtensa: patch_text: Fixup last cpu should be master

Merge tag 'erofs-for-5.18-rc4-fixes' of git://git./linux/kernel/git/xiang/erofs

Pull erofs fixes from Gao Xiang:
"One patch to fix a use-after-free race related to the on-stack
  z_erofs_decompressqueue, which happens very rarely but needs to be
  fixed properly soon.

  The other patch fixes some sysfs Sphinx warnings"

* tag 'erofs-for-5.18-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  Documentation/ABI: sysfs-fs-erofs: Fix Sphinx errors
  erofs: fix use-after-free of on-stack io[]

Revert "fs/pipe: use kvcalloc to allocate a pipe_buffer array"

This reverts commit 5a519c8fe4d620912385f94372fc8472fa98c662.

It turns out that making the pipe almost arbitrarily large has some
rather unexpected downsides.  The kernel test robot reports a kernel
warning that is due to pipe->max_usage now growing to the point where
the iter_file_splice_write() buffer allocation can no longer be
satisfied as a slab allocation, and the

        int nbufs = pipe->max_usage;
        struct bio_vec *array = kcalloc(nbufs, sizeof(struct bio_vec),
                                        GFP_KERNEL);

code sequence there will now always fail as a result.

That code could be modified to use kvcalloc() too, but I feel very
uncomfortable making those kinds of changes for a very niche use case
that really should have other options than make these kinds of
fundamental changes to pipe behavior.

Maybe the CRIU process dumping should be multi-threaded, and use
multiple pipes and multiple cores, rather than try to use one larger
pipe to minimize splice() calls.

Reported-by: kernel test robot <oliver.sang@intel.com>
Link: https://lore.kernel.org/all/20220420073717.GD16310@xsang-OptiPlex-9020/
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: __memcpy_flushcache: fix wrong alignment if size > 2^32

The first "if" condition in __memcpy_flushcache is supposed to align the
"dest" variable to 8 bytes and copy data up to this alignment. However,
this condition may misbehave if "size" is greater than 4GiB.

The statement min_t(unsigned, size, ALIGN(dest, 8) - dest); casts both
arguments to unsigned int and selects the smaller one. However, the
cast truncates high bits in "size" and it results in misbehavior.

For example:

suppose that size == 0x100000001, dest == 0x200000002
min_t(unsigned, size, ALIGN(dest, 8) - dest) == min_t(0x1, 0xe) == 0x1;
...
dest += 0x1;

so we copy just one byte "and" dest remains unaligned.

This patch fixes the bug by replacing unsigned with size_t.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

selftests: mlxsw: vxlan_flooding_ipv6: Prevent flooding of unwanted packets

The test verifies that packets are correctly flooded by the bridge and
the VXLAN device by matching on the encapsulated packets at the other
end. However, if packets other than those generated by the test also
ingress the bridge (e.g., MLD packets), they will be flooded as well and
interfere with the expected count.

Make the test more robust by making sure that only the packets generated
by the test can ingress the bridge. Drop all the rest using tc filters
on the egress of 'br0' and 'h1'.

In the software data path, the problem can be solved by matching on the
inner destination MAC or dropping unwanted packets at the egress of the
VXLAN device, but this is not currently supported by mlxsw.

Fixes: d01724dd2a66 ("selftests: mlxsw: spectrum-2: Add a test for VxLAN flooding with IPv6")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: mlxsw: vxlan_flooding: Prevent flooding of unwanted packets

The test verifies that packets are correctly flooded by the bridge and
the VXLAN device by matching on the encapsulated packets at the other
end. However, if packets other than those generated by the test also
ingress the bridge (e.g., MLD packets), they will be flooded as well and
interfere with the expected count.

Make the test more robust by making sure that only the packets generated
by the test can ingress the bridge. Drop all the rest using tc filters
on the egress of 'br0' and 'h1'.

In the software data path, the problem can be solved by matching on the
inner destination MAC or dropping unwanted packets at the egress of the
VXLAN device, but this is not currently supported by mlxsw.

Fixes: 94d302deae25 ("selftests: mlxsw: Add a test for VxLAN flooding")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ALSA: usb-audio: Clear MIDI port active flag after draining

When a rawmidi output stream is closed, it calls the drain at first,
then does trigger-off only when the drain returns -ERESTARTSYS as a
fallback.  It implies that each driver should turn off the stream
properly after the drain.  Meanwhile, USB-audio MIDI interface didn't
change the port->active flag after the drain.  This may leave the
output work picking up the port that is closed right now, which
eventually leads to a use-after-free for the already released rawmidi
object.

This patch fixes the bug by properly clearing the port->active flag
after the output drain.

Reported-by: syzbot+70e777a39907d6d5fd0a@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/00000000000011555605dceaff03@google.com
Link: https://lore.kernel.org/r/20220420130247.22062-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>

dt-bindings: dmaengine: qcom: gpi: Add minItems for interrupts

Add the minItems for interrupts property as well. In the absence of
this, we get warning if interrupts are less than 13

arch/arm64/boot/dts/qcom/qrb5165-rb5.dtb:
dma-controller@800000: interrupts: [[0, 588, 4], [0, 589, 4], [0, 590,
4], [0, 591, 4], [0, 592, 4], [0, 593, 4], [0, 594, 4], [0, 595, 4], [0,
596, 4], [0, 597, 4]] is too short

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220414064235.1182195-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

nfc: MAINTAINERS: add Bug entry

Add a Bug section, indicating preferred mailing method for bug reports,
to NFC Subsystem entry.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

dmaengine: idxd: skip clearing device context when device is read-only

If the device shows up as read-only configuration, skip the clearing of the
state as the context must be preserved for device re-enable after being
disabled.

Fixes: 0dcfe41e9a4c ("dmanegine: idxd: cleanup all device related bits after disabling device")
Reported-by: Tony Zhu <tony.zhu@intel.com>
Tested-by: Tony Zhu <tony.zhu@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/164971479479.2200566.13980022473526292759.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dmaengine: idxd: add RO check for wq max_transfer_size write

Block wq_max_transfer_size_store() when the device is configured as
read-only and not configurable.

Fixes: d7aad5550eca ("dmaengine: idxd: add support for configurable max wq xfer size")
Reported-by: Bernice Zhang <bernice.zhang@intel.com>
Tested-by: Bernice Zhang <bernice.zhang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/164971488154.2200913.10706665404118545941.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dmaengine: idxd: add RO check for wq max_batch_size write

Block wq_max_batch_size_store() when the device is configured as read-only
and not configurable.

Fixes: e7184b159dd3 ("dmaengine: idxd: add support for configurable max wq batch size")
Reported-by: Bernice Zhang <bernice.zhang@intel.com>
Tested-by: Bernice Zhang <bernice.zhang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/164971493551.2201159.1942042593642155209.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dmaengine: idxd: fix retry value to be constant for duration of function call

When retries is compared to wq->enqcmds_retries each loop of idxd_enqcmds(),
wq->enqcmds_retries can potentially changed by user. Assign the value
of retries to wq->enqcmds_retries during initialization so it is the
original value set when entering the function.

Fixes: 7930d8553575 ("dmaengine: idxd: add knob for enqcmds retries")
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/165031760154.3658664.1983547716619266558.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dmaengine: idxd: match type for retries var in idxd_enqcmds()

wq->enqcmds_retries is defined as unsigned int. However, retries on the
stack is defined as int. Change retries to unsigned int to compare the same
type.

Fixes: 7930d8553575 ("dmaengine: idxd: add knob for enqcmds retries")
Suggested-by: Thiago Macieira <thiago.macieira@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/165031747059.3658198.6035308204505664375.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dmaengine: dw-edma: Fix inconsistent indenting

Eliminate the follow smatch warning:

drivers/dma/dw-edma/dw-edma-v0-core.c:419 dw_edma_v0_core_start() warn:
inconsistent indenting.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220413023442.18856-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

net: stmmac: Use readl_poll_timeout_atomic() in atomic state

The init_systime() may be invoked in atomic state. We have observed the
following call trace when running "phc_ctl /dev/ptp0 set" on a Intel
Agilex board.
  BUG: sleeping function called from invalid context at drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:74
  in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 381, name: phc_ctl
  preempt_count: 1, expected: 0
  RCU nest depth: 0, expected: 0
  Preemption disabled at:
  [<ffff80000892ef78>] stmmac_set_time+0x34/0x8c
  CPU: 2 PID: 381 Comm: phc_ctl Not tainted 5.18.0-rc2-next-20220414-yocto-standard+ #567
  Hardware name: SoCFPGA Agilex SoCDK (DT)
  Call trace:
   dump_backtrace.part.0+0xc4/0xd0
   show_stack+0x24/0x40
   dump_stack_lvl+0x7c/0xa0
   dump_stack+0x18/0x34
   __might_resched+0x154/0x1c0
   __might_sleep+0x58/0x90
   init_systime+0x78/0x120
   stmmac_set_time+0x64/0x8c
   ptp_clock_settime+0x60/0x9c
   pc_clock_settime+0x6c/0xc0
   __arm64_sys_clock_settime+0x88/0xf0
   invoke_syscall+0x5c/0x130
   el0_svc_common.constprop.0+0x4c/0x100
   do_el0_svc+0x7c/0xa0
   el0_svc+0x58/0xcc
   el0t_64_sync_handler+0xa4/0x130
   el0t_64_sync+0x18c/0x190

So we should use readl_poll_timeout_atomic() here instead of
readl_poll_timeout().

Also adjust the delay time to 10us to fix a "__bad_udelay" build error
reported by "kernel test robot <lkp@intel.com>". I have tested this on
Intel Agilex and NXP S32G boards, there is no delay needed at all.
So the 10us delay should be long enough for most cases.

Fixes: ff8ed737860e ("net: stmmac: use readl_poll_timeout() function in init_systime()")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

doc/ip-sysctl: add bc_forwarding

Let's describe this sysctl.

Fixes: 5cbf777cfdf6 ("route: add support for directed broadcast forwarding")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drm/i915/display/psr: Unset enable_psr2_sel_fetch if other checks in intel_psr2_config_valid() fails

If any of the PSR2 checks after intel_psr2_sel_fetch_config_valid()
fails, enable_psr2_sel_fetch will be kept enabled causing problems
in the functions that only checks for it and not for has_psr2.

So here moving the check that do not depend on enable_psr2_sel_fetch
and for the remaning ones jumping to a section that unset
enable_psr2_sel_fetch in case of failure to support PSR2.

Fixes: 6e43e276b8c9 ("drm/i915: Initial implementation of PSR2 selective fetch")
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414151118.21980-1-jose.souza@intel.com
(cherry picked from commit 554ae8dce1268789e72767a67f0635cb743b3cea)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

vmalloc: replace VM_NO_HUGE_VMAP with VM_ALLOW_HUGE_VMAP

Huge page backed vmalloc memory could benefit performance in many cases.
However, some users of vmalloc may not be ready to handle huge pages for
various reasons: hardware constraints, potential pages split, etc.
VM_NO_HUGE_VMAP was introduced to allow vmalloc users to opt-out huge
pages. However, it is not easy to track down all the users that require
the opt-out, as the allocation are passed different stacks and may cause
issues in different layers.

To address this issue, replace VM_NO_HUGE_VMAP with an opt-in flag,
VM_ALLOW_HUGE_VMAP, so that users that benefit from huge pages could ask
specificially.

Also, remove vmalloc_no_huge() and add opt-in helper vmalloc_huge().

Fixes: fac54e2bfb5b ("x86/Kconfig: Select HAVE_ARCH_HUGE_VMALLOC with HAVE_ARCH_HUGE_VMAP")
Link: https://lore.kernel.org/netdev/14444103-d51b-0fb3-ee63-c3f182f0b546@molgen.mpg.de/"
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <song@kernel.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drm/msm: Revert "drm/msm: Stop using iommu_present()"

This reverts commit e2a88eabb02410267519b838fb9b79f5206769be. The commit
in question makes msm_use_mmu() check whether the DRM 'component master'
device is translated by the IOMMU. At this moment it is the 'mdss'
device.
However on platforms using the MDP5 driver (e.g. MSM8916/APQ8016,
MSM8996/APQ8096) it's the mdp5 device, which has the iommus property
(and thus is "translated by the IOMMU"). This results in these devices
being broken with the following lines in the dmesg.

[drm] Initialized msm 1.9.0 20130625 for 1a00000.mdss on minor 0
msm 1a00000.mdss: [drm:adreno_request_fw] loaded qcom/a300_pm4.fw from new location
msm 1a00000.mdss: [drm:adreno_request_fw] loaded qcom/a300_pfp.fw from new location
msm 1a00000.mdss: [drm:get_pages] *ERROR* could not get pages: -28
msm 1a00000.mdss: could not allocate stolen bo
msm 1a00000.mdss: [drm:get_pages] *ERROR* could not get pages: -28
msm 1a00000.mdss: [drm:msm_alloc_stolen_fb] *ERROR* failed to allocate buffer object
msm 1a00000.mdss: [drm:msm_fbdev_create] *ERROR* failed to allocate fb

Getting the mdp5 device pointer from this function is not that easy at
this moment. Thus this patch is reverted till the MDSS rework [1] lands.
It will make the mdp5/dpu1 device component master and the check will be
legit.

[1] https://patchwork.freedesktop.org/series/98525/

Fixes: e2a88eabb024 ("drm/msm: Stop using iommu_present()")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220419130422.1033699-1-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>

Merge tag 'spi-fix-v5.18-rc3' of git://git./linux/kernel/git/broonie/spi

Pull spi fixes from Mark Brown:
"A few more fixes for SPI, plus one new PCI ID for another Intel
  chipset.

  All device specific stuff"

* tag 'spi-fix-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: atmel-quadspi: Fix the buswidth adjustment between spi-mem and controller
  spi: cadence-quadspi: fix incorrect supports_op() return value
  spi: intel: Add support for Raptor Lake-S SPI serial flash
  spi: spi-mtk-nor: initialize spi controller after resume

fs: fix acl translation

Last cycle we extended the idmapped mounts infrastructure to support
idmapped mounts of idmapped filesystems (No such filesystem yet exist.).
Since then, the meaning of an idmapped mount is a mount whose idmapping
is different from the filesystems idmapping.

While doing that work we missed to adapt the acl translation helpers.
They still assume that checking for the identity mapping is enough.  But
they need to use the no_idmapping() helper instead.

Note, POSIX ACLs are always translated right at the userspace-kernel
boundary using the caller's current idmapping and the initial idmapping.
The order depends on whether we're coming from or going to userspace.
The filesystem's idmapping doesn't matter at the border.

Consequently, if a non-idmapped mount is passed we need to make sure to
always pass the initial idmapping as the mount's idmapping and not the
filesystem idmapping.  Since it's irrelevant here it would yield invalid
ids and prevent setting acls for filesystems that are mountable in a
userns and support posix acls (tmpfs and fuse).

I verified the regression reported in [1] and verified that this patch
fixes it.  A regression test will be added to xfstests in parallel.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=215849
Fixes: bd303368b776 ("fs: support mapped mounts of mapped filesystems")
Cc: Seth Forshee <sforshee@digitalocean.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # 5.17
Cc: <regressions@lists.linux.dev>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'asoc-fix-v5.18-rc3' of https://git./linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v5.18

A collection of fixes that came in since the merge window, plus one new
device ID for an x86 laptop. Nothing that really stands out with
particularly big impact outside of the affected device.

netlink: reset network and mac headers in netlink_dump()

netlink_dump() is allocating an skb, reserves space in it
but forgets to reset network header.

This allows a BPF program, invoked later from sk_filter()
to access uninitialized kernel memory from the reserved
space.

Theorically mac header reset could be omitted, because
it is set to a special initial value.
bpf_internal_load_pointer_neg_helper calls skb_mac_header()
without checking skb_mac_header_was_set().
Relying on skb->len not being too big seems fragile.
We also could add a sanity check in bpf_internal_load_pointer_neg_helper()
to avoid surprises in the future.

syzbot report was:

BUG: KMSAN: uninit-value in ___bpf_prog_run+0xa22b/0xb420 kernel/bpf/core.c:1637
___bpf_prog_run+0xa22b/0xb420 kernel/bpf/core.c:1637
__bpf_prog_run32+0x121/0x180 kernel/bpf/core.c:1796
bpf_dispatcher_nop_func include/linux/bpf.h:784 [inline]
__bpf_prog_run include/linux/filter.h:626 [inline]
bpf_prog_run include/linux/filter.h:633 [inline]
__bpf_prog_run_save_cb+0x168/0x580 include/linux/filter.h:756
bpf_prog_run_save_cb include/linux/filter.h:770 [inline]
sk_filter_trim_cap+0x3bc/0x8c0 net/core/filter.c:150
sk_filter include/linux/filter.h:905 [inline]
netlink_dump+0xe0c/0x16c0 net/netlink/af_netlink.c:2276
netlink_recvmsg+0x1129/0x1c80 net/netlink/af_netlink.c:2002
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
sock_read_iter+0x5a9/0x630 net/socket.c:1039
do_iter_readv_writev+0xa7f/0xc70
do_iter_read+0x52c/0x14c0 fs/read_write.c:786
vfs_readv fs/read_write.c:906 [inline]
do_readv+0x432/0x800 fs/read_write.c:943
__do_sys_readv fs/read_write.c:1034 [inline]
__se_sys_readv fs/read_write.c:1031 [inline]
__x64_sys_readv+0xe5/0x120 fs/read_write.c:1031
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:81
entry_SYSCALL_64_after_hwframe+0x44/0xae

Uninit was stored to memory at:
___bpf_prog_run+0x96c/0xb420 kernel/bpf/core.c:1558
__bpf_prog_run32+0x121/0x180 kernel/bpf/core.c:1796
bpf_dispatcher_nop_func include/linux/bpf.h:784 [inline]
__bpf_prog_run include/linux/filter.h:626 [inline]
bpf_prog_run include/linux/filter.h:633 [inline]
__bpf_prog_run_save_cb+0x168/0x580 include/linux/filter.h:756
bpf_prog_run_save_cb include/linux/filter.h:770 [inline]
sk_filter_trim_cap+0x3bc/0x8c0 net/core/filter.c:150
sk_filter include/linux/filter.h:905 [inline]
netlink_dump+0xe0c/0x16c0 net/netlink/af_netlink.c:2276
netlink_recvmsg+0x1129/0x1c80 net/netlink/af_netlink.c:2002
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
sock_read_iter+0x5a9/0x630 net/socket.c:1039
do_iter_readv_writev+0xa7f/0xc70
do_iter_read+0x52c/0x14c0 fs/read_write.c:786
vfs_readv fs/read_write.c:906 [inline]
do_readv+0x432/0x800 fs/read_write.c:943
__do_sys_readv fs/read_write.c:1034 [inline]
__se_sys_readv fs/read_write.c:1031 [inline]
__x64_sys_readv+0xe5/0x120 fs/read_write.c:1031
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:81
entry_SYSCALL_64_after_hwframe+0x44/0xae

Uninit was created at:
slab_post_alloc_hook mm/slab.h:737 [inline]
slab_alloc_node mm/slub.c:3244 [inline]
__kmalloc_node_track_caller+0xde3/0x14f0 mm/slub.c:4972
kmalloc_reserve net/core/skbuff.c:354 [inline]
__alloc_skb+0x545/0xf90 net/core/skbuff.c:426
alloc_skb include/linux/skbuff.h:1158 [inline]
netlink_dump+0x30f/0x16c0 net/netlink/af_netlink.c:2242
netlink_recvmsg+0x1129/0x1c80 net/netlink/af_netlink.c:2002
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
sock_read_iter+0x5a9/0x630 net/socket.c:1039
do_iter_readv_writev+0xa7f/0xc70
do_iter_read+0x52c/0x14c0 fs/read_write.c:786
vfs_readv fs/read_write.c:906 [inline]
do_readv+0x432/0x800 fs/read_write.c:943
__do_sys_readv fs/read_write.c:1034 [inline]
__se_sys_readv fs/read_write.c:1031 [inline]
__x64_sys_readv+0xe5/0x120 fs/read_write.c:1031
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:81
entry_SYSCALL_64_after_hwframe+0x44/0xae

CPU: 0 PID: 3470 Comm: syz-executor751 Not tainted 5.17.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: db65a3aaf29e ("netlink: Trim skb to alloc size to avoid MSG_TRUNC")
Fixes: 9063e21fb026 ("netlink: autosize skb lengthes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220415181442.551228-1-eric.dumazet@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: mscc: ocelot: fix broken IP multicast flooding

When the user runs:
bridge link set dev $br_port mcast_flood on

this command should affect not only L2 multicast, but also IPv4 and IPv6
multicast.

In the Ocelot switch, unknown multicast gets flooded according to
different PGIDs according to its type, and PGID_MC only handles L2
multicast. Therefore, by leaving PGID_MCIPV4 and PGID_MCIPV6 at their
default value of 0, unknown IP multicast traffic is never flooded.

Fixes: 421741ea5672 ("net: mscc: ocelot: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220415151950.219660-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: hellcreek: Calculate checksums in tagger

In case the checksum calculation is offloaded to the DSA master network
interface, it will include the switch trailing tag. As soon as the switch strips
that tag on egress, the calculated checksum is wrong.

Therefore, add the checksum calculation to the tagger (if required) before
adding the switch tag. This way, the hellcreek code works with all DSA master
interfaces regardless of their declared feature set.

Fixes: 01ef09caad66 ("net: dsa: Add tag handling for Hirschmann Hellcreek switches")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220415103320.90657-1-kurt@linutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

drm/i915/display/vrr: Reset VRR capable property on a long hpd

With some VRR panels, user can turn VRR ON/OFF on the fly from the panel settings.
When VRR is turned OFF ,sends a long HPD to the driver clearing the Ignore MSA bit
in the DPCD. Currently the driver parses that onevery HPD but fails to reset
the corresponding VRR Capable Connector property.
Hence the userspace still sees this as VRR Capable panel which is incorrect.

Fix this by explicitly resetting the connector property.

v2: Reset vrr capable if status == connector_disconnected
v3: Use i915 and use bool vrr_capable (Jani Nikula)
v4: Move vrr_capable to after update modes call (Jani N)
Remove the redundant comment (Jan N)
v5: Fixes the regression on older platforms by resetting the VRR
only if HAS_VRR
v6: Remove the checks from driver, add in drm core before
setting VRR prop (Ville)
v7: Move VRR set/reset to set/unset_edid (Ville)

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 9bc34b4d0f3c ("drm/i915/display/vrr: Reset VRR capable property on a long hpd")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303233222.4698-1-manasi.d.navare@intel.com
(cherry picked from commit d999ad1079f574be06a8f1701cd24a5dc0ada48c)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

ALSA: usb-audio: add mapping for MSI MAG X570S Torpedo MAX.

The USB audio device 0db0:a073 based on the Realtek ALC4080 chipset
exposes all playback volume controls as "PCM". This makes
distinguishing the individual functions hard.
The mapping already adopted for device 0db0:419c based on the same
chipset fixes the issue, apply it for this device too.

Signed-off-by: Maurizio Avogadro <mavoga@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Yl1ykPaGgsFf3SnW@ryzen
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda/i915: Fix one too many pci_dev_put()

pci_get_class() will already unref the pci device passed as argument.
So if it's unconditionally unref'ed, even if the loop is not stopped,
there will be one too many unref for each device not matched.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5701
Fixes: c9db8a30d9f0 ("ALSA: hda/i915 - skip acomp init if no matching display")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20220416064418.2364582-1-lucas.demarchi@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

net: atlantic: invert deep par in pm functions, preventing null derefs

This will reset deeply on freeze and thaw instead of suspend and
resume and prevent null pointer dereferences of the uninitialized ring
0 buffer while thawing.

The impact is an indefinitely hanging kernel. You can't switch
consoles after this and the only possible user interaction is SysRq.

BUG: kernel NULL pointer dereference
RIP: 0010:aq_ring_rx_fill+0xcf/0x210 [atlantic]
aq_vec_init+0x85/0xe0 [atlantic]
aq_nic_init+0xf7/0x1d0 [atlantic]
atl_resume_common+0x4f/0x100 [atlantic]
pci_pm_thaw+0x42/0xa0

resolves in aq_ring.o to

```
0000000000000ae0 <aq_ring_rx_fill>:
{
/* ... */
baf: 48 8b 43 08 mov 0x8(%rbx),%rax
buff->flags = 0U; /* buff is NULL */
```

The bug has been present since the introduction of the new pm code in
8aaa112a57c1 ("net: atlantic: refactoring pm logic") and was hidden
until 8ce84271697a ("net: atlantic: changes for multi-TC support"),
which refactored the aq_vec_{free,alloc} functions into
aq_vec_{,ring}_{free,alloc}, but is technically not wrong. The
original functions just always reinitialized the buffers on S3/S4. If
the interface is down before freezing, the bug does not occur. It does
not matter, whether the initrd contains and loads the module before
thawing.

So the fix is to invert the boolean parameter deep in all pm function
calls, which was clearly intended to be set like that.

First report was on Github [1], which you have to guess from the
resume logs in the posted dmesg snippet. Recently I posted one on
Bugzilla [2], since I did not have an AQC device so far.

#regzbot introduced: 8ce84271697a
#regzbot from: koo5 <kolman.jindrich@gmail.com>
#regzbot monitor: https://github.com/Aquantia/AQtion/issues/32

Fixes: 8aaa112a57c1 ("net: atlantic: refactoring pm logic")
Link: https://github.com/Aquantia/AQtion/issues/32
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215798
Cc: stable@vger.kernel.org
Reported-by: koo5 <kolman.jindrich@gmail.com>
Signed-off-by: Manuel Ullmann <labre@posteo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.18-20220417' of git://git./linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2022-04-17

this is a pull request of 1 patch for net/master.

The patch is by Oliver Hartkopp and fixes a timeout monitoring problem
in the ISO TP protocol found by the syzbot.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Linux 5.18-rc3

Merge tag 'for-linus-5.18-rc3-tag' of git://git./linux/kernel/git/xen/tip

Pull xen fixlet from Juergen Gross:
"A single cleanup patch for the Xen balloon driver"

* tag 'for-linus-5.18-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: don't use PV mode extra memory for zone device allocations

Merge tag 'x86-urgent-2022-04-17' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Thomas Gleixner:
"Two x86 fixes related to TSX:

   - Use either MSR_TSX_FORCE_ABORT or MSR_IA32_TSX_CTRL to disable TSX
     to cover all CPUs which allow to disable it.

   - Disable TSX development mode at boot so that a microcode update
     which provides TSX development mode does not suddenly make the
     system vulnerable to TSX Asynchronous Abort"

* tag 'x86-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tsx: Disable TSX development mode at boot
  x86/tsx: Use MSR_TSX_CTRL to clear CPUID bits

Merge tag 'timers-urgent-2022-04-17' of git://git./linux/kernel/git/tip/tip

Pull timer fixes from Thomas Gleixner:
"A small set of fixes for the timers core:

   - Fix the warning condition in __run_timers() which does not take
     into account that a CPU base (especially the deferrable base) never
     has a timer armed on it and therefore the next_expiry value can
     become stale.

   - Replace a WARN_ON() in the NOHZ code with a WARN_ON_ONCE() to
     prevent endless spam in dmesg.

   - Remove the double star from a comment which is not meant to be in
     kernel-doc format"

* tag 'timers-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/sched: Fix non-kernel-doc comment
  tick/nohz: Use WARN_ON_ONCE() to prevent console saturation
  timers: Fix warning condition in __run_timers()

Merge tag 'smp-urgent-2022-04-17' of git://git./linux/kernel/git/tip/tip

Pull SMP fixes from Thomas Gleixner:
"Two fixes for the SMP core:

   - Make the warning condition in flush_smp_call_function_queue()
     correct, which checked a just emptied list head for being empty
     instead of validating that there was no pending entry on the
     offlined CPU at all.

   - The @cpu member of struct cpuhp_cpu_state is initialized when the
     CPU hotplug thread for the upcoming CPU is created. That's too late
     because the creation of the thread can fail and then the following
     rollback operates on CPU0. Get rid of the CPU member and hand the
     CPU number to the involved functions directly"

* tag 'smp-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Remove the 'cpu' member of cpuhp_cpu_state
  smp: Fix offline cpu check in flush_smp_call_function_queue()

Merge tag 'irq-urgent-2022-04-17' of git://git./linux/kernel/git/tip/tip

Pull irq fix from Thomas Gleixner:
"A single fix for the interrupt affinity spreading logic to take into
  account that there can be an imbalance between present and possible
  CPUs, which causes already assigned bits to be overwritten"

* tag 'irq-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/affinity: Consider that CPUs on nodes can be unbalanced

Merge tag 'for-v5.18-rc' of git://git./linux/kernel/git/sre/linux-power-supply

Pull power supply fixes from Sebastian Reichel:

- Fix a regression with battery data failing to load from DT

* tag 'for-v5.18-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: Reset err after not finding static battery
power: supply: samsung-sdi-battery: Add missing charge restart voltages

Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux

Pull i2c fixes from Wolfram Sang:
"Regular set of fixes for drivers and the dev-interface"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: ismt: Fix undefined behavior due to shift overflowing the constant
  i2c: dev: Force case user pointers in compat_i2cdev_ioctl()
  i2c: dev: check return value when calling dev_set_name()
  i2c: qcom-geni: Use dev_err_probe() for GPI DMA error
  i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit
  i2c: pasemi: Wait for write xfers to finish

can: isotp: stop timeout monitoring when no first frame was sent

The first attempt to fix a the 'impossible' WARN_ON_ONCE(1) in
isotp_tx_timer_handler() focussed on the identical CAN IDs created by
the syzbot reproducer and lead to upstream fix/commit 3ea566422cbd
("can: isotp: sanitize CAN ID checks in isotp_bind()"). But this did
not catch the root cause of the wrong tx.state in the tx_timer handler.

In the isotp 'first frame' case a timeout monitoring needs to be started
before the 'first frame' is send. But when this sending failed the timeout
monitoring for this specific frame has to be disabled too.

Otherwise the tx_timer is fired with the 'warn me' tx.state of ISOTP_IDLE.

Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/20220405175112.2682-1-socketcan@hartkopp.net
Reported-by: syzbot+2339c27f5c66c652843e@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

bonding: do not discard lowest hash bit for non layer3+4 hashing

Commit b5f862180d70 was introduced to discard lowest hash bit for layer3+4 hashing
but it also removes last bit from non layer3+4 hashing

Below script shows layer2+3 hashing will result in same slave to be used with above commit.
$ cat hash.py
#/usr/bin/python3.6

h_dests=[0xa0, 0xa1]
h_source=0xe3
hproto=0x8
saddr=0x1e7aa8c0
daddr=0x17aa8c0

for h_dest in h_dests:
    hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
    hash ^= hash >> 16
    hash ^= hash >> 8
    print(hash)

print("with last bit removed")
for h_dest in h_dests:
    hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
    hash ^= hash >> 16
    hash ^= hash >> 8
    hash = hash >> 1
    print(hash)

Output:
$ python3.6 hash.py
522133332
522133333   <-------------- will result in both slaves being used

with last bit removed
261066666
261066666   <-------------- only single slave used

Signed-off-by: suresh kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'devicetree-fixes-for-5.18-2' of git://git./linux/kernel/git/robh/linux

Pull devicetree fixes from Rob Herring:

- Fix scalar property schemas with array constraints

- Fix 'enum' lists with duplicate entries

- Fix incomplete if/then/else schemas

- Add Renesas RZ/V2L SoC support to Mali Bifrost binding

- Maintainers update for Marvell irqchip

* tag 'devicetree-fixes-for-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: display: panel-timing: Define a single type for properties
  dt-bindings: Fix array constraints on scalar properties
  dt-bindings: gpu: mali-bifrost: Document RZ/V2L SoC
  dt-bindings: net: snps: remove duplicate name
  dt-bindings: Fix 'enum' lists with duplicate entries
  dt-bindings: irqchip: mrvl,intc: refresh maintainers
  dt-bindings: Fix incomplete if/then/else schemas
  dt-bindings: power: renesas,apmu: Fix cpus property limits
  dt-bindings: extcon: maxim,max77843: fix ports type

Merge tag 'gpio-fixes-for-v5.18-rc3' of git://git./linux/kernel/git/brgl/linux

Pull gpio fixes from Bartosz Golaszewski:
"A single fix for gpio-sim and two patches for GPIO ACPI pulled from
  Andy:

   - fix the set/get_multiple() callbacks in gpio-sim

   - use correct format characters in gpiolib-acpi

   - use an unsigned type for pins in gpiolib-acpi"

* tag 'gpio-fixes-for-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: sim: fix setting and getting multiple lines
  gpiolib: acpi: Convert type for pin to be unsigned
  gpiolib: acpi: use correct format characters

Merge tag 'soc-fixes-5.18-2' of git://git./linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
"There are a number of SoC bugfixes that came in since the merge
  window, and more of them are already pending.

  This batch includes:

   - A boot time regression fix for davinci that triggered on
     multi_v5_defconfig when booting any platform

   - Defconfig updates to address removed features, changed symbol names
     or dependencies, for gemini, ux500, and pxa

   - Email address changes for Krzysztof Kozlowski

   - Build warning fixes for ep93xx and iop32x

   - Devicetree warning fixes across many platforms

   - Minor bugfixes for the reset controller, memory controller and SCMI
     firmware subsystems plus the versatile-express board"

* tag 'soc-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (34 commits)
  ARM: config: Update Gemini defconfig
  arm64: dts: qcom/sdm845-shift-axolotl: Fix boolean properties with values
  ARM: dts: align SPI NOR node name with dtschema
  ARM: dts: Fix more boolean properties with values
  arm/arm64: dts: qcom: Fix boolean properties with values
  arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
  arm: dts: imx: Fix boolean properties with values
  arm64: dts: tegra: Fix boolean properties with values
  arm: dts: at91: Fix boolean properties with values
  arm: configs: imote2: Drop defconfig as board support dropped.
  ep93xx: clock: Don't use plain integer as NULL pointer
  ep93xx: clock: Fix UAF in ep93xx_clk_register_gate()
  ARM: vexpress/spc: Fix all the kernel-doc build warnings
  ARM: vexpress/spc: Fix kernel-doc build warning for ve_spc_cpu_in_wfi
  ARM: config: u8500: Re-enable AB8500 battery charging
  ARM: config: u8500: Add some common hardware
  memory: fsl_ifc: populate child nodes of buses and mfd devices
  ARM: config: Refresh U8500 defconfig
  firmware: arm_scmi: Fix sparse warnings in OPTEE transport driver
  firmware: arm_scmi: Replace zero-length array with flexible-array member
  ...

Merge tag 'random-5.18-rc3-for-linus' of git://git./linux/kernel/git/crng/random

Pull random number generator fixes from Jason Donenfeld:

- Per your suggestion, random reads now won't fail if there's a page
   fault after some non-zero amount of data has been read, which makes
   the behavior consistent with all other reads in the kernel.

- Rather than an inconsistent mix of random_get_entropy() returning an
   unsigned long or a cycles_t, now it just returns an unsigned long.

- A memcpy() was replaced with an memmove(), because the addresses are
   sometimes overlapping. In practice the destination is always before
   the source, so not really an issue, but better to be correct than
   not.

* tag 'random-5.18-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
  random: use memmove instead of memcpy for remaining 32 bytes
  random: make random_get_entropy() return an unsigned long
  random: allow partial reads if later user copies fail

Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
"13 fixes, all in drivers.

  The most extensive changes are in the iscsi series (affecting drivers
  qedi, cxgbi and bnx2i), the next most is scsi_debug, but that's just a
  simple revert and then minor updates to pm80xx"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: iscsi: MAINTAINERS: Add Mike Christie as co-maintainer
  scsi: qedi: Fix failed disconnect handling
  scsi: iscsi: Fix NOP handling during conn recovery
  scsi: iscsi: Merge suspend fields
  scsi: iscsi: Fix unbound endpoint error handling
  scsi: iscsi: Fix conn cleanup and stop race during iscsid restart
  scsi: iscsi: Fix endpoint reuse regression
  scsi: iscsi: Release endpoint ID when its freed
  scsi: iscsi: Fix offload conn cleanup when iscsid restarts
  scsi: iscsi: Move iscsi_ep_disconnect()
  scsi: pm80xx: Enable upper inbound, outbound queues
  scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63
  Revert "scsi: scsi_debug: Address races following module load"

Merge tag 'intel-gpio-v5.18-2' of gitolite.pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-current

intel-gpio for v5.18-2

* Couple of fixes related to handling unsigned value of the pin from ACPI

gpiolib:
- acpi: Convert type for pin to be unsigned
- acpi: use correct format characters

Merge tag 'dma-mapping-5.18-2' of git://git.infradead.org/users/hch/dma-mapping

Pull dma-mapping fix from Christoph Hellwig:

- avoid a double memory copy for swiotlb (Chao Gao)

* tag 'dma-mapping-5.18-2' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: avoid redundant memory sync for swiotlb

random: use memmove instead of memcpy for remaining 32 bytes

In order to immediately overwrite the old key on the stack, before
servicing a userspace request for bytes, we use the remaining 32 bytes
of block 0 as the key. This means moving indices 8,9,a,b,c,d,e,f ->
4,5,6,7,8,9,a,b. Since 4 < 8, for the kernel implementations of
memcpy(), this doesn't actually appear to be a problem in practice. But
relying on that characteristic seems a bit brittle. So let's change that
to a proper memmove(), which is the by-the-books way of handling
overlapping memory copies.

Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>

xtensa: fix a7 clobbering in coprocessor context load/store

Fast coprocessor exception handler saves a3..a6, but coprocessor context
load/store code uses a4..a7 as temporaries, potentially clobbering a7.
'Potentially' because coprocessor state load/store macros may not use
all four temporary registers (and neither FPU nor HiFi macros do).
Use a3..a6 as intended.

Cc: stable@vger.kernel.org
Fixes: c658eac628aa ("[XTENSA] Add support for configurable registers and coprocessors")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>

Merge branch 'akpm' (patches from Andrew)

Merge misc fixes from Andrew Morton:
"14 patches.

  Subsystems affected by this patch series: MAINTAINERS, binfmt, and
  mm (tmpfs, secretmem, kasan, kfence, pagealloc, zram, compaction,
  hugetlb, vmalloc, and kmemleak)"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: kmemleak: take a full lowmem check in kmemleak_*_phys()
  mm/vmalloc: fix spinning drain_vmap_work after reading from /proc/vmcore
  revert "fs/binfmt_elf: use PT_LOAD p_align values for static PIE"
  revert "fs/binfmt_elf: fix PT_LOAD p_align values for loaders"
  hugetlb: do not demote poisoned hugetlb pages
  mm: compaction: fix compiler warning when CONFIG_COMPACTION=n
  mm: fix unexpected zeroed page mapping with zram swap
  mm, page_alloc: fix build_zonerefs_node()
  mm, kfence: support kmem_dump_obj() for KFENCE objects
  kasan: fix hw tags enablement when KUNIT tests are disabled
  irq_work: use kasan_record_aux_stack_noalloc() record callstack
  mm/secretmem: fix panic when growing a memfd_secret
  tmpfs: fix regressions from wider use of ZERO_PAGE
  MAINTAINERS: Broadcom internal lists aren't maintainers

Merge tag 'for-5.18/dm-fixes-2' of git://git./linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

- Fix memory corruption in DM integrity target when tag_size is less
   than digest size.

- Fix DM multipath's historical-service-time path selector to not use
   sched_clock() and ktime_get_ns(); only use ktime_get_ns().

- Fix dm_io->orig_bio NULL pointer dereference in dm_zone_map_bio() due
   to 5.18 changes that overlooked DM zone's use of ->orig_bio

- Fix for regression that broke the use of dm_accept_partial_bio() for
   "abnormal" IO (e.g. WRITE ZEROES) that does not need duplicate bios

- Fix DM's issuing of empty flush bio so that it's size is 0.

* tag 'for-5.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix bio length of empty flush
  dm: allow dm_accept_partial_bio() for dm_io without duplicate bios
  dm zone: fix NULL pointer dereference in dm_zone_map_bio
  dm mpath: only use ktime_get_ns() in historical selector
  dm integrity: fix memory corruption when tag_size is less than digest size

mm: kmemleak: take a full lowmem check in kmemleak_*_phys()

The kmemleak_*_phys() apis do not check the address for lowmem's min
boundary, while the caller may pass an address below lowmem, which will
trigger an oops:

  # echo scan > /sys/kernel/debug/kmemleak
  Unable to handle kernel paging request at virtual address ff5fffffffe00000
  Oops [#1]
  Modules linked in:
  CPU: 2 PID: 134 Comm: bash Not tainted 5.18.0-rc1-next-20220407 #33
  Hardware name: riscv-virtio,qemu (DT)
  epc : scan_block+0x74/0x15c
   ra : scan_block+0x72/0x15c
  epc : ffffffff801e5806 ra : ffffffff801e5804 sp : ff200000104abc30
   gp : ffffffff815cd4e8 tp : ff60000004cfa340 t0 : 0000000000000200
   t1 : 00aaaaaac23954cc t2 : 00000000000003ff s0 : ff200000104abc90
   s1 : ffffffff81b0ff28 a0 : 0000000000000000 a1 : ff5fffffffe01000
   a2 : ffffffff81b0ff28 a3 : 0000000000000002 a4 : 0000000000000001
   a5 : 0000000000000000 a6 : ff200000104abd7c a7 : 0000000000000005
   s2 : ff5fffffffe00ff9 s3 : ffffffff815cd998 s4 : ffffffff815d0e90
   s5 : ffffffff81b0ff28 s6 : 0000000000000020 s7 : ffffffff815d0eb0
   s8 : ffffffffffffffff s9 : ff5fffffffe00000 s10: ff5fffffffe01000
   s11: 0000000000000022 t3 : 00ffffffaa17db4c t4 : 000000000000000f
   t5 : 0000000000000001 t6 : 0000000000000000
  status: 0000000000000100 badaddr: ff5fffffffe00000 cause: 000000000000000d
    scan_gray_list+0x12e/0x1a6
    kmemleak_scan+0x2aa/0x57e
    kmemleak_write+0x32a/0x40c
    full_proxy_write+0x56/0x82
    vfs_write+0xa6/0x2a6
    ksys_write+0x6c/0xe2
    sys_write+0x22/0x2a
    ret_from_syscall+0x0/0x2

The callers may not quite know the actual address they pass(e.g. from
devicetree).  So the kmemleak_*_phys() apis should guarantee the address
they finally use is in lowmem range, so check the address for lowmem's
min boundary.

Link: https://lkml.kernel.org/r/20220413122925.33856-1-patrick.wang.shcn@gmail.com
Signed-off-by: Patrick Wang <patrick.wang.shcn@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/vmalloc: fix spinning drain_vmap_work after reading from /proc/vmcore

Commit 3ee48b6af49c ("mm, x86: Saving vmcore with non-lazy freeing of
vmas") introduced set_iounmap_nonlazy(), which sets vmap_lazy_nr to
lazy_max_pages() + 1, ensuring that any future vunmaps() immediately
purge the vmap areas instead of doing it lazily.

Commit 690467c81b1a ("mm/vmalloc: Move draining areas out of caller
context") moved the purging from the vunmap() caller to a worker thread.
Unfortunately, set_iounmap_nonlazy() can cause the worker thread to spin
(possibly forever).  For example, consider the following scenario:

1. Thread reads from /proc/vmcore. This eventually calls
    __copy_oldmem_page() -> set_iounmap_nonlazy(), which sets
    vmap_lazy_nr to lazy_max_pages() + 1.

2. Then it calls free_vmap_area_noflush() (via iounmap()), which adds 2
    pages (one page plus the guard page) to the purge list and
    vmap_lazy_nr. vmap_lazy_nr is now lazy_max_pages() + 3, so the
    drain_vmap_work is scheduled.

3. Thread returns from the kernel and is scheduled out.

4. Worker thread is scheduled in and calls drain_vmap_area_work(). It
    frees the 2 pages on the purge list. vmap_lazy_nr is now
    lazy_max_pages() + 1.

5. This is still over the threshold, so it tries to purge areas again,
    but doesn't find anything.

6. Repeat 5.

If the system is running with only one CPU (which is typicial for kdump)
and preemption is disabled, then this will never make forward progress:
there aren't any more pages to purge, so it hangs.  If there is more
than one CPU or preemption is enabled, then the worker thread will spin
forever in the background.  (Note that if there were already pages to be
purged at the time that set_iounmap_nonlazy() was called, this bug is
avoided.)

This can be reproduced with anything that reads from /proc/vmcore
multiple times.  E.g., vmcore-dmesg /proc/vmcore.

It turns out that improvements to vmap() over the years have obsoleted
the need for this "optimization".  I benchmarked `dd if=/proc/vmcore
of=/dev/null` with 4k and 1M read sizes on a system with a 32GB vmcore.
The test was run on 5.17, 5.18-rc1 with a fix that avoided the hang, and
5.18-rc1 with set_iounmap_nonlazy() removed entirely:

    |5.17  |5.18+fix|5.18+removal
  4k|40.86s|  40.09s|      26.73s
  1M|24.47s|  23.98s|      21.84s

The removal was the fastest (by a wide margin with 4k reads).  This
patch removes set_iounmap_nonlazy().

Link: https://lkml.kernel.org/r/52f819991051f9b865e9ce25605509bfdbacadcd.1649277321.git.osandov@fb.com
Fixes: 690467c81b1a  ("mm/vmalloc: Move draining areas out of caller context")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Acked-by: Chris Down <chris@chrisdown.name>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

revert "fs/binfmt_elf: use PT_LOAD p_align values for static PIE"

Despite Mike's attempted fix (925346c129da117122), regressions reports
continue:

  https://lore.kernel.org/lkml/cb5b81bd-9882-e5dc-cd22-54bdbaaefbbc@leemhuis.info/
  https://bugzilla.kernel.org/show_bug.cgi?id=215720
  https://lkml.kernel.org/r/b685f3d0-da34-531d-1aa9-479accd3e21b@leemhuis.info

So revert this patch.

Fixes: 9630f0d60fec ("fs/binfmt_elf: use PT_LOAD p_align values for static PIE")
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Chris Kennelly <ckennelly@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Fangrui Song <maskray@google.com>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Sandeep Patil <sspatil@google.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

revert "fs/binfmt_elf: fix PT_LOAD p_align values for loaders"

Commit 925346c129da11 ("fs/binfmt_elf: fix PT_LOAD p_align values for
loaders") was an attempt to fix regressions due to 9630f0d60fec5f
("fs/binfmt_elf: use PT_LOAD p_align values for static PIE").

But regressionss continue to be reported:

  https://lore.kernel.org/lkml/cb5b81bd-9882-e5dc-cd22-54bdbaaefbbc@leemhuis.info/
  https://bugzilla.kernel.org/show_bug.cgi?id=215720
  https://lkml.kernel.org/r/b685f3d0-da34-531d-1aa9-479accd3e21b@leemhuis.info

This patch reverts the fix, so the original can also be reverted.

Fixes: 925346c129da11 ("fs/binfmt_elf: fix PT_LOAD p_align values for loaders")
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Chris Kennelly <ckennelly@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Sandeep Patil <sspatil@google.com>
Cc: Fangrui Song <maskray@google.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hugetlb: do not demote poisoned hugetlb pages

It is possible for poisoned hugetlb pages to reside on the free lists.
The huge page allocation routines which dequeue entries from the free
lists make a point of avoiding poisoned pages.  There is no such check
and avoidance in the demote code path.

If a hugetlb page on the is on a free list, poison will only be set in
the head page rather then the page with the actual error.  If such a
page is demoted, then the poison flag may follow the wrong page.  A page
without error could have poison set, and a page with poison could not
have the flag set.

Check for poison before attempting to demote a hugetlb page.  Also,
return -EBUSY to the caller if only poisoned pages are on the free list.

Link: https://lkml.kernel.org/r/20220307215707.50916-1-mike.kravetz@oracle.com
Fixes: 8531fc6f52f5 ("hugetlb: add hugetlb demote page support")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: compaction: fix compiler warning when CONFIG_COMPACTION=n

The below warning is reported when CONFIG_COMPACTION=n:

   mm/compaction.c:56:27: warning: 'HPAGE_FRAG_CHECK_INTERVAL_MSEC' defined but not used [-Wunused-const-variable=]
      56 | static const unsigned int HPAGE_FRAG_CHECK_INTERVAL_MSEC = 500;
         |                           ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Fix it by moving 'HPAGE_FRAG_CHECK_INTERVAL_MSEC' under
CONFIG_COMPACTION defconfig.

Also since this is just a 'static const int' type, use #define for it.

Link: https://lkml.kernel.org/r/1647608518-20924-1-git-send-email-quic_charante@quicinc.com
Signed-off-by: Charan Teja Kalla <quic_charante@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Nitin Gupta <nigupta@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: fix unexpected zeroed page mapping with zram swap

Two processes under CLONE_VM cloning, user process can be corrupted by
seeing zeroed page unexpectedly.

      CPU A                        CPU B

  do_swap_page                do_swap_page
  SWP_SYNCHRONOUS_IO path     SWP_SYNCHRONOUS_IO path
  swap_readpage valid data
    swap_slot_free_notify
      delete zram entry
                              swap_readpage zeroed(invalid) data
                              pte_lock
                              map the *zero data* to userspace
                              pte_unlock
  pte_lock
  if (!pte_same)
    goto out_nomap;
  pte_unlock
  return and next refault will
  read zeroed data

The swap_slot_free_notify is bogus for CLONE_VM case since it doesn't
increase the refcount of swap slot at copy_mm so it couldn't catch up
whether it's safe or not to discard data from backing device.  In the
case, only the lock it could rely on to synchronize swap slot freeing is
page table lock.  Thus, this patch gets rid of the swap_slot_free_notify
function.  With this patch, CPU A will see correct data.

      CPU A                        CPU B

  do_swap_page                do_swap_page
  SWP_SYNCHRONOUS_IO path     SWP_SYNCHRONOUS_IO path
                              swap_readpage original data
                              pte_lock
                              map the original data
                              swap_free
                                swap_range_free
                                  bd_disk->fops->swap_slot_free_notify
  swap_readpage read zeroed data
                              pte_unlock
  pte_lock
  if (!pte_same)
    goto out_nomap;
  pte_unlock
  return
  on next refault will see mapped data by CPU B

The concern of the patch would increase memory consumption since it
could keep wasted memory with compressed form in zram as well as
uncompressed form in address space.  However, most of cases of zram uses
no readahead and do_swap_page is followed by swap_free so it will free
the compressed form from in zram quickly.

Link: https://lkml.kernel.org/r/YjTVVxIAsnKAXjTd@google.com
Fixes: 0bcac06f27d7 ("mm, swap: skip swapcache for swapin of synchronous device")
Reported-by: Ivan Babrou <ivan@cloudflare.com>
Tested-by: Ivan Babrou <ivan@cloudflare.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, page_alloc: fix build_zonerefs_node()

Since commit 6aa303defb74 ("mm, vmscan: only allocate and reclaim from
zones with pages managed by the buddy allocator") only zones with free
memory are included in a built zonelist.  This is problematic when e.g.
all memory of a zone has been ballooned out when zonelists are being
rebuilt.

The decision whether to rebuild the zonelists when onlining new memory
is done based on populated_zone() returning 0 for the zone the memory
will be added to.  The new zone is added to the zonelists only, if it
has free memory pages (managed_zone() returns a non-zero value) after
the memory has been onlined.  This implies, that onlining memory will
always free the added pages to the allocator immediately, but this is
not true in all cases: when e.g. running as a Xen guest the onlined new
memory will be added only to the ballooned memory list, it will be freed
only when the guest is being ballooned up afterwards.

Another problem with using managed_zone() for the decision whether a
zone is being added to the zonelists is, that a zone with all memory
used will in fact be removed from all zonelists in case the zonelists
happen to be rebuilt.

Use populated_zone() when building a zonelist as it has been done before
that commit.

There was a report that QubesOS (based on Xen) is hitting this problem.
Xen has switched to use the zone device functionality in kernel 5.9 and
QubesOS wants to use memory hotplugging for guests in order to be able
to start a guest with minimal memory and expand it as needed.  This was
the report leading to the patch.

Link: https://lkml.kernel.org/r/20220407120637.9035-1-jgross@suse.com
Fixes: 6aa303defb74 ("mm, vmscan: only allocate and reclaim from zones with pages managed by the buddy allocator")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, kfence: support kmem_dump_obj() for KFENCE objects

Calling kmem_obj_info() via kmem_dump_obj() on KFENCE objects has been
producing garbage data due to the object not actually being maintained
by SLAB or SLUB.

Fix this by implementing __kfence_obj_info() that copies relevant
information to struct kmem_obj_info when the object was allocated by
KFENCE; this is called by a common kmem_obj_info(), which also calls the
slab/slub/slob specific variant now called __kmem_obj_info().

For completeness, kmem_dump_obj() now displays if the object was
allocated by KFENCE.

Link: https://lore.kernel.org/all/20220323090520.GG16885@xsang-OptiPlex-9020/
Link: https://lkml.kernel.org/r/20220406131558.3558585-1-elver@google.com
Fixes: b89fb5ef0ce6 ("mm, kfence: insert KFENCE hooks for SLUB")
Fixes: d3fb45f370d9 ("mm, kfence: insert KFENCE hooks for SLAB")
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz> [slab]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kasan: fix hw tags enablement when KUNIT tests are disabled

Kasan enables hw tags via kasan_enable_tagging() which based on the mode
passed via kernel command line selects the correct hw backend.
kasan_enable_tagging() is meant to be invoked indirectly via the cpu
features framework of the architectures that support these backends.
Currently the invocation of this function is guarded by
CONFIG_KASAN_KUNIT_TEST which allows the enablement of the correct backend
only when KUNIT tests are enabled in the kernel.

This inconsistency was introduced in commit:

ed6d74446cbf ("kasan: test: support async (again) and asymm modes for HW_TAGS")

... and prevents to enable MTE on arm64 when KUNIT tests for kasan hw_tags are
disabled.

Fix the issue making sure that the CONFIG_KASAN_KUNIT_TEST guard does not
prevent the correct invocation of kasan_enable_tagging().

Link: https://lkml.kernel.org/r/20220408124323.10028-1-vincenzo.frascino@arm.com
Fixes: ed6d74446cbf ("kasan: test: support async (again) and asymm modes for HW_TAGS")
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

irq_work: use kasan_record_aux_stack_noalloc() record callstack

On PREEMPT_RT kernel and KASAN is enabled.  the kasan_record_aux_stack()
may call alloc_pages(), and the rt-spinlock will be acquired, if currently
in atomic context, will trigger warning:

  BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
  in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 239, name: bootlogd
  Preemption disabled at:
  [<ffffffffbab1a531>] rt_mutex_slowunlock+0xa1/0x4e0
  CPU: 3 PID: 239 Comm: bootlogd Tainted: G        W 5.17.1-rt17-yocto-preempt-rt+ #105
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
  Call Trace:
     __might_resched.cold+0x13b/0x173
     rt_spin_lock+0x5b/0xf0
     get_page_from_freelist+0x20c/0x1610
     __alloc_pages+0x25e/0x5e0
     __stack_depot_save+0x3c0/0x4a0
     kasan_save_stack+0x3a/0x50
     __kasan_record_aux_stack+0xb6/0xc0
     kasan_record_aux_stack+0xe/0x10
     irq_work_queue_on+0x6a/0x1c0
     pull_rt_task+0x631/0x6b0
     do_balance_callbacks+0x56/0x80
     __balance_callbacks+0x63/0x90
     rt_mutex_setprio+0x349/0x880
     rt_mutex_slowunlock+0x22a/0x4e0
     rt_spin_unlock+0x49/0x80
     uart_write+0x186/0x2b0
     do_output_char+0x2e9/0x3a0
     n_tty_write+0x306/0x800
     file_tty_write.isra.0+0x2af/0x450
     tty_write+0x22/0x30
     new_sync_write+0x27c/0x3a0
     vfs_write+0x3f7/0x5d0
     ksys_write+0xd9/0x180
     __x64_sys_write+0x43/0x50
     do_syscall_64+0x44/0x90
     entry_SYSCALL_64_after_hwframe+0x44/0xae

Fix it by using kasan_record_aux_stack_noalloc() to avoid the call to
alloc_pages().

Link: https://lkml.kernel.org/r/20220402142555.2699582-1-qiang1.zhang@intel.com
Signed-off-by: Zqiang <qiang1.zhang@intel.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/secretmem: fix panic when growing a memfd_secret

When one tries to grow an existing memfd_secret with ftruncate, one gets
a panic [1].  For example, doing the following reliably induces the
panic:

    fd = memfd_secret();

    ftruncate(fd, 10);
    ptr = mmap(NULL, 10, PROT_READ | PROT_WRITE, MAP_SHARED, fd, 0);
    strcpy(ptr, "123456789");

    munmap(ptr, 10);
    ftruncate(fd, 20);

The basic reason for this is, when we grow with ftruncate, we call down
into simple_setattr, and then truncate_inode_pages_range, and eventually
we try to zero part of the memory.  The normal truncation code does this
via the direct map (i.e., it calls page_address() and hands that to
memset()).

For memfd_secret though, we specifically don't map our pages via the
direct map (i.e.  we call set_direct_map_invalid_noflush() on every
fault).  So the address returned by page_address() isn't useful, and
when we try to memset() with it we panic.

This patch avoids the panic by implementing a custom setattr for
memfd_secret, which detects resizes specifically (setting the size for
the first time works just fine, since there are no existing pages to try
to zero), and rejects them with EINVAL.

One could argue growing should be supported, but I think that will
require a significantly more lengthy change.  So, I propose a minimal
fix for the benefit of stable kernels, and then perhaps to extend
memfd_secret to support growing in a separate patch.

[1]:

  BUG: unable to handle page fault for address: ffffa0a889277028
  #PF: supervisor write access in kernel mode
  #PF: error_code(0x0002) - not-present page
  PGD afa01067 P4D afa01067 PUD 83f909067 PMD 83f8bf067 PTE 800ffffef6d88060
  Oops: 0002 [#1] PREEMPT SMP DEBUG_PAGEALLOC PTI
  CPU: 0 PID: 281 Comm: repro Not tainted 5.17.0-dbg-DEV #1
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
  RIP: 0010:memset_erms+0x9/0x10
  Code: c1 e9 03 40 0f b6 f6 48 b8 01 01 01 01 01 01 01 01 48 0f af c6 f3 48 ab 89 d1 f3 aa 4c 89 c8 c3 90 49 89 f9 40 88 f0 48 89 d1 <f3> aa 4c 89 c8 c3 90 49 89 fa 40 0f b6 ce 48 b8 01 01 01 01 01 01
  RSP: 0018:ffffb932c09afbf0 EFLAGS: 00010246
  RAX: 0000000000000000 RBX: ffffda63c4249dc0 RCX: 0000000000000fd8
  RDX: 0000000000000fd8 RSI: 0000000000000000 RDI: ffffa0a889277028
  RBP: ffffb932c09afc00 R08: 0000000000001000 R09: ffffa0a889277028
  R10: 0000000000020023 R11: 0000000000000000 R12: ffffda63c4249dc0
  R13: ffffa0a890d70d98 R14: 0000000000000028 R15: 0000000000000fd8
  FS:  00007f7294899580(0000) GS:ffffa0af9bc00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: ffffa0a889277028 CR3: 0000000107ef6006 CR4: 0000000000370ef0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   ? zero_user_segments+0x82/0x190
   truncate_inode_partial_folio+0xd4/0x2a0
   truncate_inode_pages_range+0x380/0x830
   truncate_setsize+0x63/0x80
   simple_setattr+0x37/0x60
   notify_change+0x3d8/0x4d0
   do_sys_ftruncate+0x162/0x1d0
   __x64_sys_ftruncate+0x1c/0x20
   do_syscall_64+0x44/0xa0
   entry_SYSCALL_64_after_hwframe+0x44/0xae
  Modules linked in: xhci_pci xhci_hcd virtio_net net_failover failover virtio_blk virtio_balloon uhci_hcd ohci_pci ohci_hcd evdev ehci_pci ehci_hcd 9pnet_virtio 9p netfs 9pnet
  CR2: ffffa0a889277028

[lkp@intel.com: secretmem_iops can be static]
Signed-off-by: kernel test robot <lkp@intel.com>
[axelrasmussen@google.com: return EINVAL]

Link: https://lkml.kernel.org/r/20220324210909.1843814-1-axelrasmussen@google.com
Link: https://lkml.kernel.org/r/20220412193023.279320-1-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: kernel test robot <lkp@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tmpfs: fix regressions from wider use of ZERO_PAGE

Chuck Lever reported fsx-based xfstests generic 075 091 112 127 failing
when 5.18-rc1 NFS server exports tmpfs: bisected to recent tmpfs change.

Whilst nfsd_splice_action() does contain some questionable handling of
repeated pages, and Chuck was able to work around there, history from
Mark Hemment makes clear that there might be similar dangers elsewhere:
it was not a good idea for me to pass ZERO_PAGE down to unknown actors.

Revert shmem_file_read_iter() to using ZERO_PAGE for holes only when
iter_is_iovec(); in other cases, use the more natural iov_iter_zero()
instead of copy_page_to_iter().

We would use iov_iter_zero() throughout, but the x86 clear_user() is not
nearly so well optimized as copy to user (dd of 1T sparse tmpfs file
takes 57 seconds rather than 44 seconds).

And now pagecache_init() does not need to SetPageUptodate(ZERO_PAGE(0)):
which had caused boot failure on arm noMMU STM32F7 and STM32H7 boards

Link: https://lkml.kernel.org/r/9a978571-8648-e830-5735-1f4748ce2e30@google.com
Fixes: 56a8c8eb1eaf ("tmpfs: do not allocate pages on read")
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Patrice CHOTARD <patrice.chotard@foss.st.com>
Reported-by: Chuck Lever III <chuck.lever@oracle.com>
Tested-by: Chuck Lever III <chuck.lever@oracle.com>
Cc: Mark Hemment <markhemm@googlemail.com>
Cc: Patrice CHOTARD <patrice.chotard@foss.st.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Lukas Czerner <lczerner@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: Broadcom internal lists aren't maintainers

Convert the broadcom internal list M: and L: entries to R: as exploder
email addresses are neither maintainers nor mailing lists.

Reorder the entries as necessary.

Link: https://lkml.kernel.org/r/04eb301f5b3adbefdd78e76657eff0acb3e3d87f.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

i2c: ismt: Fix undefined behavior due to shift overflowing the constant

Fix:

  drivers/i2c/busses/i2c-ismt.c: In function ‘ismt_hw_init’:
  drivers/i2c/busses/i2c-ismt.c:770:2: error: case label does not reduce to an integer constant
    case ISMT_SPGT_SPD_400K:
    ^~~~
  drivers/i2c/busses/i2c-ismt.c:773:2: error: case label does not reduce to an integer constant
    case ISMT_SPGT_SPD_1M:
    ^~~~

See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.

Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

i2c: dev: Force case user pointers in compat_i2cdev_ioctl()

Sparse has warned us about wrong address space for user pointers:

  i2c-dev.c:561:50: warning: incorrect type in initializer (different address spaces)
  i2c-dev.c:561:50:    expected unsigned char [usertype] *buf
  i2c-dev.c:561:50:    got void [noderef] __user *

Force cast the pointer to (__u8 *) that is used by I²C core code.

Note, this is an additional fix to the previously addressed similar issue
in the I2C_RDWR case in the same function.

Fixes: 3265a7e6b41b ("i2c: dev: Add __user annotation")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

net: lan966x: Make sure to release ptp interrupt

When the lan966x driver is removed make sure to remove also the ptp_irq
IRQ.

Fixes: e85a96e48e3309 ("net: lan966x: Add support for ptp interrupts")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220413195716.3796467-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ipv6: make ip6_rt_gc_expire an atomic_t

Reads and Writes to ip6_rt_gc_expire always have been racy,
as syzbot reported lately [1]

There is a possible risk of under-flow, leading
to unexpected high value passed to fib6_run_gc(),
although I have not observed this in the field.

Hosts hitting ip6_dst_gc() very hard are under pretty bad
state anyway.

[1]
BUG: KCSAN: data-race in ip6_dst_gc / ip6_dst_gc

read-write to 0xffff888102110744 of 4 bytes by task 13165 on cpu 1:
ip6_dst_gc+0x1f3/0x220 net/ipv6/route.c:3311
dst_alloc+0x9b/0x160 net/core/dst.c:86
ip6_dst_alloc net/ipv6/route.c:344 [inline]
icmp6_dst_alloc+0xb2/0x360 net/ipv6/route.c:3261
mld_sendpack+0x2b9/0x580 net/ipv6/mcast.c:1807
mld_send_cr net/ipv6/mcast.c:2119 [inline]
mld_ifc_work+0x576/0x800 net/ipv6/mcast.c:2651
process_one_work+0x3d3/0x720 kernel/workqueue.c:2289
worker_thread+0x618/0xa70 kernel/workqueue.c:2436
kthread+0x1a9/0x1e0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30

read-write to 0xffff888102110744 of 4 bytes by task 11607 on cpu 0:
ip6_dst_gc+0x1f3/0x220 net/ipv6/route.c:3311
dst_alloc+0x9b/0x160 net/core/dst.c:86
ip6_dst_alloc net/ipv6/route.c:344 [inline]
icmp6_dst_alloc+0xb2/0x360 net/ipv6/route.c:3261
mld_sendpack+0x2b9/0x580 net/ipv6/mcast.c:1807
mld_send_cr net/ipv6/mcast.c:2119 [inline]
mld_ifc_work+0x576/0x800 net/ipv6/mcast.c:2651
process_one_work+0x3d3/0x720 kernel/workqueue.c:2289
worker_thread+0x618/0xa70 kernel/workqueue.c:2436
kthread+0x1a9/0x1e0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30

value changed: 0x00000bb3 -> 0x00000ba9

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 11607 Comm: kworker/0:21 Not tainted 5.18.0-rc1-syzkaller-00037-g42e7a03d3bad-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: mld mld_ifc_work

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220413181333.649424-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'l3mdev-fix-ip-tunnel-case-after-recent-l3mdev-change'

David Ahern says:

====================
l3mdev: Fix ip tunnel case after recent l3mdev change

Second patch provides a fix for ip tunnels after the recent l3mdev change
that avoids touching the oif in the flow struct. First patch preemptively
provides a fix to an existing function that the second patch uses.
====================

Link: https://lore.kernel.org/r/20220413174320.28989-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: Handle l3mdev in ip_tunnel_init_flow

Ido reported that the commit referenced in the Fixes tag broke
a gre use case with dummy devices. Add a check to ip_tunnel_init_flow
to see if the oif is an l3mdev port and if so set the oif to 0 to
avoid the oif comparison in fib_lookup_good_nhc.

Fixes: 40867d74c374 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

l3mdev: l3mdev_master_upper_ifindex_by_index_rcu should be using netdev_master_upper_dev_get_rcu

Next patch uses l3mdev_master_upper_ifindex_by_index_rcu which throws
a splat with debug kernels:

[13783.087570] ------------[ cut here ]------------
[13783.093974] RTNL: assertion failed at net/core/dev.c (6702)
[13783.100761] WARNING: CPU: 3 PID: 51132 at net/core/dev.c:6702 netdev_master_upper_dev_get+0x16a/0x1a0

[13783.184226] CPU: 3 PID: 51132 Comm: kworker/3:3 Not tainted 5.17.0-custom-100090-g6f963aafb1cc #682
[13783.194788] Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017
[13783.204755] Workqueue: mld mld_ifc_work [ipv6]
[13783.210338] RIP: 0010:netdev_master_upper_dev_get+0x16a/0x1a0
[13783.217209] Code: 0f 85 e3 fe ff ff e8 65 ac ec fe ba 2e 1a 00 00 48 c7 c6 60 6f 38 83 48 c7 c7 c0 70 38 83 c6 05 5e b5 d7 01 01 e8 c6 29 52 00 <0f> 0b e9 b8 fe ff ff e8 5a 6c 35 ff e9 1c ff ff ff 48 89 ef e8 7d
[13783.238659] RSP: 0018:ffffc9000b37f5a8 EFLAGS: 00010286
[13783.244995] RAX: 0000000000000000 RBX: ffff88812ee5c000 RCX: 0000000000000000
[13783.253379] RDX: ffff88811ce09d40 RSI: ffffffff812d0fcd RDI: fffff5200166fea7
[13783.261769] RBP: 0000000000000000 R08: 0000000000000001 R09: ffff8882375f4287
[13783.270138] R10: ffffed1046ebe850 R11: 0000000000000001 R12: dffffc0000000000
[13783.278510] R13: 0000000000000275 R14: ffffc9000b37f688 R15: ffff8881273b4af8
[13783.286870] FS:  0000000000000000(0000) GS:ffff888237400000(0000) knlGS:0000000000000000
[13783.296352] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[13783.303177] CR2: 00007ff25fc9b2e8 CR3: 0000000174d23000 CR4: 00000000001006e0
[13783.311546] Call Trace:
[13783.314660]  <TASK>
[13783.317553]  l3mdev_master_upper_ifindex_by_index_rcu+0x43/0xe0
...

Change l3mdev_master_upper_ifindex_by_index_rcu to use
netdev_master_upper_dev_get_rcu.

Fixes: 6a6d6681ac1a ("l3mdev: add function to retreive upper master")
Signed-off-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Alexis Bauvin <abauvin@scaleway.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'net-sched-two-fixes-for-cls_u32'

Eric Dumazet says:

====================
net/sched: two fixes for cls_u32

One syzbot report brought my attention to cls_u32.

This series addresses the syzbot report, and an additional
issue discovered in code review.
====================

Link: https://lore.kernel.org/r/20220413173542.533060-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/sched: cls_u32: fix possible leak in u32_init_knode()

While investigating a related syzbot report,
I found that whenever call to tcf_exts_init()
from u32_init_knode() is failing, we end up
with an elevated refcount on ht->refcnt

To avoid that, only increase the refcount after
all possible errors have been evaluated.

Fixes: b9a24bb76bf6 ("net_sched: properly handle failure case of tcf_exts_init()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>