arm64: dts: qcom: msm8916: Disable venus by default

Venus needs firmware that is usually signed with a device-specific key.
There are also devices that might not need it (especially during
bring-up), so let's follow more recent SoCs and disable it by default.

Enable it explicitly for all current devices except msm8916-mtp. That
one has just UART enabled currently so it cannot really benefit from
Venus.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-1-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7180: Add ADSP

sc7180 has an ADSP remoteproc that exclusively controls the audio
hardware on devices that use Qualcomm firmware.

Add it along with the relevant audio services.

Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230907-sc7180-adsp-rproc-v3-4-6515c3fbe0a3@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7180: Add tertiary mi2s pinctrl

Some devices use tertiary mi2s to connect external audio codec.
Add it near the other two i2s pinctrl definitions so the devices don't
have to duplicate it.

Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230907-sc7180-adsp-rproc-v3-3-6515c3fbe0a3@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

Revert "arm64: dts: qcom: sm8450: Add PRNG"

This reverts commit 76a6dd7bfcbb ("arm64: dts: qcom: sm8450: Add PRNG"),
since the RNG HW on the SM8450 SoC is in fact a True Random Number Generator,
a more appropriate compatible should be instead as reported at [1].

[1] https://lore.kernel.org/all/20230818161720.3644424-1-quic_omprsing@quicinc.com/

Suggested-by: Om Prakash Singh <quic_omprsing@quicinc.com>
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230828-topic-sm8550-rng-v3-1-7a0678ca7988@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: pm8916: Drop codec reg-names and mclk

Drop the redundant reg-names and mclk from the PM8916 analog codec that
were removed from the DT schema. Having the mclk on the analog codec is
incorrect because only the digital codec consumes it directly.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230718-pm8916-mclk-v1-6-4b4a58b4240a@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdx75-idp: align RPMh regulator nodes with bindings

Device node names should be generic and bindings expect certain pattern
for RPMh regulator nodes:

  sdx75-idp.dtb: rsc@17a00000: 'pmx75-rpmh-regulators' does not match any of the regexes: '^regulators(-[0-9])?$', 'pinctrl-[0-9]+'

Fixes: 8a2dc39d1043 ("arm64: dts: qcom: sdx75-idp: Add regulator nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905163103.257412-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm4250-billie2: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  sm4250-oneplus-billie2.dtb: phy@4807000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-13-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8998-sagit: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  msm8998-xiaomi-sagit.dtb: phy@1da7000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-12-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8998-oneplus: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  msm8998-oneplus-dumpling.dtb: phy@1da7000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-11-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8998-mtp: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  msm8998-mtp.dtb: phy@1da7000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-10-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8998-pro1: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  msm8998-fxtec-pro1.dtb: phy@1da7000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-9-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8996-gemini: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  msm8996-xiaomi-gemini.dtb: phy@627000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8996-oneplus: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  msm8996-oneplus3t.dtb: phy@627000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: apq8096-db820c: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  apq8096-db820c.dtb: phy@627000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6115p-j606f: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  sm6115p-lenovo-j606f.dtb: phy@4807000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6115-pro1x: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  sm6115-fxtec-pro1x.dtb: phy@4807000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6125-sprout: correct UFS pad supply

The Qualcomm UFS phy switched from dedicated driver to QMP phy driver.
Eventually the old driver was removed in commit 02dca8c981b5 ("phy:
qcom: remove ufs qmp phy driver").  The original driver and its binding
used vddp-ref-clk regulator supply, but the new one did not and left the
supply unused.

The Qualcomm UFS phy bindings were also migrated to newer ones and
dropped support for vddp-ref-clk regulator in commit dc5cb63592bd
("dt-bindings: phy: migrate QMP UFS PHY bindings to
qcom,sc8280xp-qmp-ufs-phy.yaml").

It turns out that this regulator, although with inaccurate name
vddp-ref-clk, is actually needed to provide supply for VDD_PX10 (or
similar, depending on the SoC) used by UFS controller.

Bring back handling of this supply by using more appropriate regulator -
UFS controller host supply.  This also fixes dtbs_check warning:

  sm6125-xiaomi-laurel-sprout.dtb: phy@4807000: 'vddp-ref-clk-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6125-sprout: drop incorrect UFS phy max current

Neither bindings nor UFS phy driver use properties like
'vdda-phy-max-microamp' and 'vdda-pll-max-microamp':

  sm6125-xiaomi-laurel-sprout.dtb: phy@4807000: 'vdda-phy-max-microamp', 'vdda-pll-max-microamp' do not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905161920.252013-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq6018: Fix tcsr_mutex register size

IPQ6018's TCSR Mutex HW lock register has 32 locks of size 4KB each.
Total size of the TCSR Mutex registers is 128KB.

Fix size of the tcsr_mutex hwlock register to 0x20000.

Changes in v2:
 - Drop change to remove qcom,ipq6018-tcsr-mutex compatible string
 - Added Fixes and stable tags

Cc: stable@vger.kernel.org
Fixes: 5bf635621245 ("arm64: dts: ipq6018: Add a few device nodes")
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230905095535.1263113-2-quic_viswanat@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq9574: Fix hwlock index for SMEM

SMEM uses lock index 3 of the TCSR Mutex hwlock for allocations
in SMEM region shared by the Host and FW.

Fix the SMEM hwlock index to 3 for IPQ9574.

Cc: stable@vger.kernel.org
Fixes: 46384ac7a618 ("arm64: dts: qcom: ipq9574: Add SMEM support")
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230904172516.479866-5-quic_viswanat@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq6018: Fix hwlock index for SMEM

SMEM uses lock index 3 of the TCSR Mutex hwlock for allocations
in SMEM region shared by the Host and FW.

Fix the SMEM hwlock index to 3 for IPQ6018.

Cc: stable@vger.kernel.org
Fixes: 5bf635621245 ("arm64: dts: ipq6018: Add a few device nodes")
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230904172516.479866-3-quic_viswanat@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq5332: Fix hwlock index for SMEM

SMEM uses lock index 3 of the TCSR Mutex hwlock for allocations
in SMEM region shared by the Host and FW.

Fix the SMEM hwlock index to 3 for IPQ5332.

Cc: stable@vger.kernel.org
Fixes: d56dd7f935e1 ("arm64: dts: qcom: ipq5332: add SMEM support")
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230904172516.479866-2-quic_viswanat@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq8074: Fix hwlock index for SMEM

SMEM uses lock index 3 of the TCSR Mutex hwlock for allocations
in SMEM region shared by the Host and FW.

Fix the SMEM hwlock index to 3 for IPQ8074.

Cc: stable@vger.kernel.org
Fixes: 42124b947e8e ("arm64: dts: qcom: ipq8074: add SMEM support")
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230904172516.479866-4-quic_viswanat@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8916-samsung-j5-common: Add accelerometer

J5 and J5X have ST LIS2HH12 accelerometer.
Add support for it.

Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Co-developed-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230904123123.2593-1-linmengbo0689@protonmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: split pmr735d into 2

The second PMR735D PMIC is not always presend on SM8550 based devices,
split the pmr735d.dtsi file in two so boards files can only include the
ones present on the platform.

Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230831-topic-sm8550-upstream-pmr735d-split-v1-1-98e632636415@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq5332: Enable USB

Enable USB2 in host mode.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/d4c20505dd2103b5421eab7602aec4f83bd62dbe.1693468292.git.quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq5332: Add USB related nodes

Add USB phy and controller nodes.

Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/f25777bfe2c84e203b7615527607900b756c51bd.1693468292.git.quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm7225-fp4: Revert "arm64: dts: qcom: sm7225-fairphone-fp4: Add AW8695 haptics"

This reverts commit 413821b7777d062b57f8dc66ab088ed390cbc3ec because it
was never reviewed, was buggy (report from kernel test robot:
https://lore.kernel.org/all/202204090333.QZXMI2tu-lkp@intel.com/) and
used undocumented, broken bindings.  Half of the properties in this
device are questioned, thus adding DTS node causes only errors and does
not make the device usable without the bindings and driver part:

  sm7225-fairphone-fp4.dtb: haptics@5a: failed to match any schema with compatible: ['awinic,aw8695']
  sm7225-fairphone-fp4.dtb: haptics@5a: awinic,tset: b'\x12' is not of type 'object', 'array', 'boolean', 'null'
  sm7225-fairphone-fp4.dtb: haptics@5a: awinic,r-spare: b'h' is not of type 'object', 'array', 'boolean', 'null'

Since bindings were abandoned (4 months since review), revert the commit
to avoid false sense of supporting something which is not supported.

Cc: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20230827122842.63741-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8180x: drop incorrect cell-index from SPMI

The SPMI controller (PMIC Arbiter) does not use nor allow 'cell-index'
property:

  sc8180x-primus.dtb: spmi@c440000: Unevaluated properties are not allowed ('cell-index' was unexpected)

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230827122842.63741-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8939-longcheer-l9100: Add initial device tree

This dts adds support for BQ Aquaris M5 (Longcheer L9100) released in
2015.

Add a device tree with initial support for:

- GPIO keys
- Hall sensor
- SDHCI
- WCNSS (BT/WIFI)
- Accelerometer/Magnetometer
- Vibrator
- Touchscreen
- Front flash

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Link: https://lore.kernel.org/r/20230827-bq_m5-v4-2-f8435fb8f955@apitzsch.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

dt-bindings: arm: qcom: Add BQ Aquaris M5

Add a compatible for BQ Aquaris M5 (Longcheer L9100).

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Link: https://lore.kernel.org/r/20230827-bq_m5-v4-1-f8435fb8f955@apitzsch.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845-mtp: enable PCIe support

Enable two PCIe hosts support on Qualcomm SDM845 MTP board.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230826221915.846937-6-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845-mtp: enable Vol-/reset button

Wire up the Vol- / reset button on Qualcomm SDM845 MTP board.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230826221915.846937-5-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845-mtp: switch to mbn firmware

We have switched most of devices to use mbn (squashed) firmware files
instead of spit mdt+bNN. Even this DT uses modem.mbn and a630_zap.mbn.
Let's switch adsp and cdsp firmware files to use .mbn format too.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230826221915.846937-4-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845-mtp: specify wifi variant

Specify the variant for the WiFi BDF file, "Qualcomm_sdm845mtp" to ease
distinguishing from other (possible) devices using the same board id.

For the reference:

ath10k_snoc 18800000.wifi: qmi chip_id 0x30214 chip_family 0x4001 board_id 0x3f soc_id 0x40030001
ath10k_snoc 18800000.wifi: qmi fw_version 0x2009856b fw_build_timestamp 2018-07-19 12:28 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
ath10k_snoc 18800000.wifi: failed to fetch board data for bus=snoc,qmi-board-id=3f,qmi-chip-id=30214,variant=Qualcomm_sdm845mtp from ath10k/WCN3990/hw1.0/board-2.bin
ath10k_snoc 18800000.wifi: wcn3990 hw1.0 target 0x00000008 chip_id 0x00000000 sub 0000:0000
ath10k_snoc 18800000.wifi: kconfig debug 1 debugfs 0 tracing 0 dfs 0 testmode 0
ath10k_snoc 18800000.wifi: firmware ver  api 5 features wowlan,mgmt-tx-by-reference,non-bmi crc32 b3d4b790
ath10k_snoc 18800000.wifi: htt-ver 3.53 wmi-op 4 htt-op 3 cal file max-sta 32 raw 0 hwcrypto 1
ath10k_snoc 18800000.wifi: invalid MAC address; choosing random

Cc: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230826221915.846937-3-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845-mtp: fix WiFi configuration

Enable the host-cap-8bit quirk on this device. It is required for the
WiFi to function properly.

Fixes: 022bccb840b7 ("arm64: dts: sdm845: Add WCN3990 WLAN module device node")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230826221915.846937-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8350-hdk: add pmr735a regulators

The SM8350 HDK uses pmr735a to supply some of the voltages (e.g. to
WiFi/BT chip). Declare corresponding regulators together with voltage
boundaries.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230825214550.1650938-3-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8350-hdk: add missing PMICs

Include configuration for several PMICs presend on the board.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230825214550.1650938-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8350: fix pinctrl for UART18

On sm8350 QUP18 uses GPIO 68/69, not 58/59. Fix correponding UART18
pinconf configuraion.

Fixes: 98374e6925b8 ("arm64: dts: qcom: sm8350: Set up WRAP2 QUPs")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230825214550.1650938-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845-tama: Add camera GPIO regulators

Like on many other platforms, Tama devices utilize lots of GPIO-
enabled regulators for the camera sensors. Define them in the DT.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230824-topic-tama_gpio-v1-3-014e9d198dce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845-tama: Add GPIO line names for PMIC GPIOs

Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).

Add these to the Akari, Apollo & Akatsuki DTS-es to better document
the hardware.

pm8005 and pm8998 config is common for all three boards.
Apollo has VIB_LDO_EN (replacing NC) on PMI8998_GPIO_5

Akari and Akatsuki have WLC_EN_N (replacing NC) on PMI8998_GPIO_8

Akari additionally has RSVD(WLC_EN_N) (replacing) on PMI8998_GPIO_11
which sounds a bit like a forgot-to-update-documentation, but maybe
it differs between SKUs.. Time will tell, when we get to enabling the
wireless charger.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230824-topic-tama_gpio-v1-2-014e9d198dce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845-tama: Add GPIO line names for TLMM

Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).

Add these to the Akari, Apollo & Akatsuki DTS-es to better document
the hardware.

Apollo can be considered the 'base configuration'. Akari brings
WLC_INT_N on GPIO_31 over that.

Akatsuki & Akari diff:

<                         "NC",
>                         "SAMD_RSTEN_N",
<                         "NC",
>                         "MASTER_RST_N",
<                         "NC",
>                         "DISP_ERR_FG",
<                         "NC",
>                         "SAMD_BOOTL_PIN",
<                         "NC",
<                         "NC",
<                         "NC", /* GPIO_60 */
>                         "SDM_SWD_CLK",
>                         "SDM_SWD_DAT",
>                         "SAMD_RST", /* GPIO_60 */
<                         "NC",
>                         "MODE_SEL2",
<                         "NC",
>                         "NFC_ESE_PWR_REQ",
<                         "NC",
>                         "TS_VDDIO_EN",

Which makes sense, as Akari and Akatsuki have a wireless charger and
Akatsuki also additionally has a super-high-end-complex-for-the-time
Samsung OLED display, as opposed to LCDs on the other Tama devices.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230824-topic-tama_gpio-v1-1-014e9d198dce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: Add support for the Xiaomi SM7125 platform

There are 6 Xiaomi smartphones with the SM7125 SoC:

- POCO M2 Pro (gram)
- Redmi Note 9S (curtana)
- Redmi Note 9 Pro (Global, joyeuse)
- Redmi Note 9 Pro (India, curtana)
- Redmi Note 9 Pro Max (excalibur)
- Redmi Note 10 Lite (curtana)

These devices share a common board design (a.k.a miatoll) with only a
few differences. Add support for the common board, as well as support
for the global Redmi Note 9 Pro.

Signed-off-by: David Wronek <davidwronek@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230824091737.75813-5-davidwronek@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: Add SM7125 device tree

The Snapdragon 720G (sm7125) is software-wise very similar to the
Snapdragon 7c with minor differences in clock speeds and as added here,
it uses the Kryo 465 instead of Kryo 468.

Signed-off-by: David Wronek <davidwronek@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230824091737.75813-4-davidwronek@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: pm6150: Add resin and rtc nodes

Add support for the RTC which is the same as on other PMICs and add the
resin child node to the PM6150 PON device, both disabled by default.

Signed-off-by: David Wronek <davidwronek@gmail.com>
Tested-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230824091737.75813-3-davidwronek@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

dt-bindings: arm: qcom: Document SM7125 and xiaomi,joyeuse board

Document the xiaomi,joyeuse board based on the Qualcomm SM7125 SoC.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David Wronek <davidwronek@gmail.com>
Link: https://lore.kernel.org/r/20230824091737.75813-2-davidwronek@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7180: Add sku_id and board id for lazor/limozeen

SKU ID 10: Lazor LTE+Wifi, no-esim (Strapped 0 X 0)
SKU ID 15: Limozeen LTE+Wifi, TS, no esim (Strapped 1 X 0)
SKU ID 18: Limozeen LTE+Wifi, no TS, no esim (Strapped X 0 0)

Even though the "no esim" boards are strapped differently than
ones that have an esim, the esim isn't represented in the
device tree so the same device tree can be used for LTE w/ esim
and LTE w/out esim.

add BRD_ID(0, Z, 0) = 10 for new board with ALC5682i-VS

Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230823151005.v6.2.I8f20fdfe34a2e8a38373bbd65587754b324f3dcb@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

dt-bindings: arm: qcom: add sc7180-lazor board bindings

Introduce more sc7180-lazor sku and board version configuration,
add no-eSIM SKU 10 for Lazor, no-eSIM SKU 15 and 18 for Limozeen,
add new board version 10 for audio codec ALC5682i-VS.

Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230823151005.v6.1.I26e017b00a341e7a5a2e94a83596923713408817@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8450: switch PCIe QMP PHY to new style of bindings

Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes). As a part of this conversion also
change the "refgen" name to more correct "rchng".

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-18-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8250: switch PCIe QMP PHY to new style of bindings

Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-17-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8150: switch PCIe QMP PHY to new style of bindings

Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes). As a part of this conversion also
add the missing "ref" clock to the PCIe PHY devices.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-16-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8150: add ref clock to PCIe PHYs

Follow the rest of the platforms and add "ref" clocks to both PCIe PHYs
found on the Qualcomm SM8150 platform.

Fixes: a1c86c680533 ("arm64: dts: qcom: sm8150: Add PCIe nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-15-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845: switch PCIe QMP PHY to new style of bindings

Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-14-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8180x: switch PCIe QMP PHY to new style of bindings

Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes). While we are at it, rename PHY
nodes to `phy@`.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-13-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7280: switch PCIe QMP PHY to new style of bindings

Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-12-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8998: switch PCIe QMP PHY to new style of bindings

Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-11-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq8074: switch PCIe QMP PHY to new style of bindings

Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-10-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq6018: switch PCIe QMP PHY to new style of bindings

Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-9-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7280: drop incorrect EUD port on SoC side

Qualcomm Embedded USB Debugger (EUD) second port should point to Type-C
USB connector.  Such connector was defined directly in root node of
sc7280.dtsi which is clearly wrong.  SC7280 is a chip, so physically it
does not have USB Type-C port.  The connector is usually accessible
through some USB switch or controller.

Doug Anderson said that he wasn't ever able to use EUD on Herobrine
boards, probably because of invalid or missing DTS description - DTS is
saying EUD is on usb_2 node, which is connected to a USB Hub, not to the
Type-C port.

Correct the EUD/USB connector topology by removing the top-level fake
USB connector and EUD port pointing to it, and disabling the incomplete
EUD device node.

This fixes also dtbs_check warnings:

  sc7280-herobrine-crd.dtb: connector: ports:port@0: 'reg' is a required property

Link: https://lore.kernel.org/all/CAD=FV=Xt26=rBf99mzkAuwwtb2f-jnKtnHaEhXnthz0a5zke4Q@mail.gmail.com/
Fixes: 9ee402ccfeb1 ("arm64: dts: qcom: sc7280: Fix EUD dt node syntax")
Cc: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Cc: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230820075626.22600-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm670: Fix pdc mapping

As pointed out by Richard, I missed a non-continuity in one of the ranges.
Fix it.

Reported-by: Richard Acayan <mailingradian@gmail.com>
Fixes: b51ee205dc4f ("arm64: dts: qcom: sdm670: Add PDC")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20230818-topic-670_pdc_fix-v1-1-1ba025041de7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: Use QCOM_SCM_VMID defines for qcom,vmid

Since we have those defines available in a header, let's use them
everywhere where qcom,vmid property is used.

Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230818-qcom-vmid-defines-v1-1-45b610c96b13@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sa8775p-ride: Describe sgmii_phy1 irq

There's an irq hooked up, so let's describe it.

Prior to commit 9757300d2750
("pinctrl: qcom: Add intr_target_width field to support increased number of interrupt targets")
one would not see the IRQ fire, despite some (invasive) debugging
showing that the GPIO was in fact asserted, resulting in the interface
staying down.

Now that the IRQ is properly routed we can describe it.

Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230817213815.638189-3-ahalaney@redhat.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sa8775p-ride: Describe sgmii_phy0 irq

There's an irq hooked up, so let's describe it.

Prior to commit 9757300d2750
("pinctrl: qcom: Add intr_target_width field to support increased number of interrupt targets")
one would not see the IRQ fire, despite some (invasive) debugging
showing that the GPIO was in fact asserted, resulting in the interface
staying down.

Now that the IRQ is properly routed we can describe it.

Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230817213815.638189-2-ahalaney@redhat.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb5165-rb5: enable DP altmode

Add displayport altmode declaration to the Type-C controller node to
enable DP altmode negotiation.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230817145940.9887-5-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb5165-rb5: enable displayport controller

Enable the onboard displayport controller, connect it to QMP PHY.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230817145940.9887-4-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb5165-rb5: add onboard USB-C redriver

Add the nb7vpq904m, onboard USB-C redriver / retimer.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230817145940.9887-3-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8250: Add DisplayPort device node

Declare the displayport controller present on the Qualcomm SM8250 SoC.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230817145940.9887-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb5165-rb5: Switch on TCPM orientation-switch for usb_1_qmpphy

Switch on USB orientation-switching for usb_1_qmp via TCPM. Detecting the
orientation switch is required to get the PHY to reset and bring-up the PHY
with the CC lines set to the appropriate lane.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230816115151.501736-8-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb5165-rb5: Switch on TCPM usb-role-switching for usb_1

Switch on usb-role-switching for usb_1 via TCPM. We need to declare
usb-role-switch in &usb_1 and associate with the remote-endpoint in TCPM
which provides the necessary signal.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230816115151.501736-7-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb5165-rb5: Switch on basic TCPM

Switch on TCPM for the RB5. Here we declare as a source only not a sink
since qrb5165 doesn't support powering exclusively from the type-c port.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230816115151.501736-6-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb5165-rb5: Switch on Type-C VBUS boost

Switch on VBUS for the Type-C port. We need to support a higher amperage
than the bootloader set 2 Amps.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230816115151.501736-5-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: pm8150b: Add a TCPM description

Type-C port management functionality lives inside of the PMIC block on
pm8150b.

The Type-C port management logic controls orientation detection, vbus/vconn
sense and to send/receive Type-C Power Domain messages.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230816115151.501736-4-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8250: Define ports for qmpphy orientation-switching

ports for orientation switching input and output. The individual board dts
files will instantiate port@0, port@1 and/or port@2 depending on the supported
feature-set.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230816115151.501736-3-bryan.odonoghue@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7180: Reorganize trogdor rt5682 audio codec dts

It was asserted that the "/delete-property/ VBAT-supply;" that we
needed to do in the rt5682s dts fragment was ugly. Let's change up all
the trogdor device trees to make it explicit which version of "rt5682"
we have and avoid the need for the "delete-property".

As a side effect, this nicely gets rid of the need for a delete-node
in coachz, which doesn't use "rt5682" at all.

A few notes:
- This doesn't get rid of every "/delete-node/" in trogdor, just the
  one that was used for rt5682s.
- Though we no longer have any "/delete-node/", we do still override
  the "model" in the "sound" node in one case (in pompom) since that
  uses the "2mic" sound setup.

This is validated to produce the same result (other than a few
properties being reordered) when taking the dtbs generated by the
kernel build and then doing:

  for dtb in *trogdor*.dtb; do
    dtc -I dtb -O dts $dtb -o out/$dtb.dts;
  done

Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Link: https://lore.kernel.org/r/20230816112143.2.I29a5a330b6994afca81871f74bbacaf55b155937@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7180: Move trogdor rt5682s bits to a fragment

Several trogdor boards have moved from the older rt5862i to the newer
rt5862s, at least on newer revisions of boards. Let's get rid of the
dts duplication across boards and promote this to a fragment.

Note: The old boards used to override the "compatible" in the "sound"
node with the exact same thing that was in "sc7180-trogdor.dtsi"
("google,sc7180-trogdor"). I got rid of that.

This is validated to produce the same result when taking the dtbs
generated by the kernel build and then doing:

  for dtb in *trogdor*.dtb; do
    dtc -I dtb -O dts $dtb -o out/$dtb.dts;
  done

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Link: https://lore.kernel.org/r/20230816112143.1.I7227efd47e0dc42b6ff243bd22aa1a3e01923220@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq5018: add watchdog

Add the required DT node for watchdog operation.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230816161455.3310629-2-robimarko@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7280-crd: add Bluetooth VDDIO supply

Bluetooth requires VDDIO supply and Doug Anderson suggested it is
vreg_l18b_1p8.  Add one to satisfy `dtbs_check`:

  sc7280-crd-r3.dtb: bluetooth: 'vddio-supply' is a required property

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230816060502.16789-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb2210-rb1: Hook up USB3

Configure the USB3 PHY to enable USB3 functionality

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230906-topic-rb1_features_sans_icc-v1-5-e92ce6fbde16@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb2210-rb1: Add GPIO LEDs

Add the three LEDs (blue/yellow/green) connected to TLMM GPIOs.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230906-topic-rb1_features_sans_icc-v1-4-e92ce6fbde16@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb2210-rb1: Enable remote processors

Enable the ADSP, MPSS and Wi-Fi. Tighten up the Wi-Fi regulators to
make them compliant with that the chip expects.

The Wi-Fi reports:
qmi chip_id 0x120 chip_family 0x4007 board_id 0xff soc_id 0x40670000

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230906-topic-rb1_features_sans_icc-v1-3-e92ce6fbde16@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb2210-rb1: Fix regulators

Commit b4fe47d12f1f ("arm64: dts: qcom: qrb2210-rb1: Add regulators")
introduced regulator settings that were never put in place, as all of the
properties ended 'microvolts' instead of 'microvolt' (which dt schema did
not check for back then).

Fix the microvolts-microvolt typo and adjust voltage ranges where it's
necessary to fit within the volt = base + n*step formula.

Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: b4fe47d12f1f ("arm64: dts: qcom: qrb2210-rb1: Add regulators")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230906-topic-rb1_features_sans_icc-v1-2-e92ce6fbde16@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb2210-rb1: Swap UART index

Newer RB1 board revisions have a debug UART on QUP0. Sadly, it looks
like even when ordering one in retail, customers receive prototype
boards with "Enginering Sample" written on them.

Use QUP4 for UART to make all known RB1 boards boot.

Fixes: e18771961336 ("arm64: dts: qcom: Add initial QTI RB1 device tree")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230906-topic-rb1_features_sans_icc-v1-1-e92ce6fbde16@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7280: Add missing LMH interrupts

Hook up the interrupts that signal the Limits Management Hardware has
started some sort of throttling action.

Fixes: 7dbd121a2c58 ("arm64: dts: qcom: sc7280: Add cpufreq hw node")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230811-topic-7280_lmhirq-v1-1-c262b6a25c8f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8180x: switch UFS QMP PHY to new style of bindings

Change the UFS QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230731111158.3998107-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7180: Link trogdor touchscreens to the panels

Let's provide the proper link from the touchscreen to the panel on
trogdor devices where the touchscreen support it. This allows the OS
to power sequence the touchscreen more properly.

For the most part, this is just expected to marginally improve power
consumption while the screen is off. However, in at least one trogdor
model (wormdingler) it's suspected that this will fix some behavorial
corner cases when the panel power cycles (like for a modeset) without
the touchscreen power cycling.

NOTE: some trogdor variants use touchscreens that don't (yet) support
linking the touchscreen and the panel. Those variants are left alone.

Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Link: https://lore.kernel.org/r/20230727101636.v4.11.Ia06c340e3482563e6bfd3106ecd0d3139f173ca4@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8916-samsung-gt510: Add capacitive keys

gt510 has two capacitive keys on the bottom. Define keycodes to enable
them.

Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20230725-gt5-panel-v1-3-7c787e33a614@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8916-samsung-gt58: Add display panel

The device has a 8 inch lsl080al03 display. Add it to the device tree.

Signed-off-by: Siddharth Manthan <siddharth.manthan@gmail.com>
Co-developed-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230725-gt5-panel-v1-2-7c787e33a614@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8916-samsung-gt510: Add display panel

The device has a 9.7 inch ltl101at01 display. Add it to the device tree.

Signed-off-by: Jasper Korten <jja2000@gmail.com>
Co-developed-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230725-gt5-panel-v1-1-7c787e33a614@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6125-seine: Configure MDSS, DSI and panel

Enable MDSS and DSI, and configure the Samsung SOFEF01-M ams597ut01
6.0" 1080x2520 panel.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-17-a3f287dd6c07@somainline.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6125: Add display hardware nodes

Add the DT nodes that describe the MDSS hardware on SM6125, containing
one MDP (display controller) together with a single DSI and DSI PHY.  No
DisplayPort support is added for now.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-16-a3f287dd6c07@somainline.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6125: Add dispcc node

Enable and configure the dispcc node on SM6125 for consumption by MDSS
later on.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-15-a3f287dd6c07@somainline.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6125: Switch fixed xo_board clock to RPM XO clock

We have a working RPM XO clock; no other driver except rpmcc should be
parenting directly to the fixed-factor xo_board clock nor should it be
reachable by that global name.  Remove the name to that effect, so that
every clock relation is explicitly defined in DTS.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-14-a3f287dd6c07@somainline.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6125: Sort spmi_bus node numerically by reg

This node has always resided in the wrong spot, making it somewhat
harder to contribute new node entries while maintaining proper sorting
around it.  Move the node up to sit after hsusb_phy1 where it maintains
proper numerical sorting on the (first of its many) reg address
property.

Fixes: cff4bbaf2a2d ("arm64: dts: qcom: Add support for SM6125")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-3-a3f287dd6c07@somainline.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6125: Pad APPS IOMMU address to 8 characters

APPS IOMMU is the only node in sm6125.dtsi that doesn't have its
address padded to 8 hexadecimals; fix this by prepending a 0.

Fixes: 8ddb4bc3d3b5 ("arm64: dts: qcom: sm6125: Configure APPS SMMU")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-2-a3f287dd6c07@somainline.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm630: align USB DWC3 clocks with bindings

Bindings require different order of clocks for USB DWC3 nodes (sleep
before mock_utmi).

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230723141849.93078-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8180x: align USB DWC3 clocks with bindings

Bindings require different order of clocks for USB DWC3 nodes (sleep
before mock_utmi).

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230723141849.93078-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8992-libra: drop duplicated reserved memory

There are two entries for similar reserved memory: qseecom@cb400000 and
audio@cb400000.  Keep the qseecom as it is longer.

  Warning (unique_unit_address_if_enabled): /reserved-memory/audio@cb400000: duplicate unit-address (also used in node /reserved-memory/qseecom@cb400000)

Fixes: 69876bc6fd4d ("arm64: dts: qcom: msm8992-libra: Fix the memory map")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230720072048.10093-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8994: fix duplicated @6c00000 reserved memory

Reserved memory @6c00000 is defined in MSM8994 DTSI and few boards:

  Warning (unique_unit_address_if_enabled): /reserved-memory/reserved@6c00000: duplicate unit-address (also used in node /reserved-memory/hole2@6c00000)
  Warning (unique_unit_address_if_enabled): /reserved-memory/reserved@6c00000: duplicate unit-address (also used in node /reserved-memory/memory@6c00000)

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230720072048.10093-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm630: Add support for modem remoteproc

Modem subsystem in SDM630/660 is similar to MSM8998 and
device tree node for it is based on the one from msm8998.dtsi.

Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Link: https://lore.kernel.org/r/20230719093458.2668842-1-alexeymin@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7280: Remove qcom,adsp-bypass-mode

This property isn't used or defined anymore. Get rid of it.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230714-topic-lpass_lpi_cleanup-v1-3-dc18b5bd14f7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>