Jacky Chou [Mon, 15 Nov 2021 03:49:41 +0000 (11:49 +0800)]
net: usb: ax88179_178a: add TSO feature
On low-effciency embedded platforms, transmission performance is poor
due to on Bulk-out with single packet.
Adding TSO feature improves the transmission performance and reduces
the number of interrupt caused by Bulk-out complete.
Reference to module, net: usb: aqc111.
Signed-off-by: Jacky Chou <jackychou@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 15 Nov 2021 14:11:25 +0000 (14:11 +0000)]
Merge branch 'mctp-i2c-driver'
Matt Johnston says:
====================
MCTP I2C driver
This patch series adds a netdev driver providing MCTP transport over
I2C.
It applies against net-next using recent MCTP changes there, though also
has I2C core changes for review. I'll leave it to maintainers where it
should be applied - please let me know if it needs to be submitted
differently.
The I2C patches were previously sent as RFC though the only feedback
there was an ack to 255 bytes for aspeed.
The dt-bindings patch went through review on the list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Mon, 15 Nov 2021 02:49:26 +0000 (10:49 +0800)]
mctp i2c: MCTP I2C binding driver
Provides MCTP network transport over an I2C bus, as specified in
DMTF DSP0237. All messages between nodes are sent as SMBus Block Writes.
Each I2C bus to be used for MCTP is flagged in devicetree by a
'mctp-controller' property on the bus node. Each flagged bus gets a
mctpi2cX net device created based on the bus number. A
'mctp-i2c-controller' I2C client needs to be added under the adapter. In
an I2C mux situation the mctp-i2c-controller node must be attached only
to the root I2C bus. The I2C client will handle incoming I2C slave block
write data for subordinate busses as well as its own bus.
In configurations without devicetree a driver instance can be attached
to a bus using the I2C slave new_device mechanism.
The MCTP core will hold/release the MCTP I2C device while responses
are pending (a 6 second timeout or once a socket is closed, response
received etc). While held the MCTP I2C driver will lock the I2C bus so
that the correct I2C mux remains selected while responses are received.
(Ideally we would just lock the mux to keep the current bus selected for
the response rather than a full I2C bus lock, but that isn't exposed in
the I2C mux API)
This driver requires I2C adapters that allow 255 byte transfers
(SMBus 3.0) as the specification requires a minimum MTU of 68 bytes.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Mon, 15 Nov 2021 02:49:25 +0000 (10:49 +0800)]
dt-bindings: net: New binding mctp-i2c-controller
Used to define a local endpoint to communicate with MCTP peripherals
attached to an I2C bus. This I2C endpoint can communicate with remote
MCTP devices on the I2C bus.
In the example I2C topology below (matching the second yaml example) we
have MCTP devices on busses i2c1 and i2c6. MCTP-supporting busses are
indicated by the 'mctp-controller' DT property on an I2C bus node.
A mctp-i2c-controller I2C client DT node is placed at the top of the
mux topology, since only the root I2C adapter will support I2C slave
functionality.
.-------.
|eeprom |
.------------. .------. /'-------'
| adapter | | mux --@0,i2c5------'
| i2c1 ----.*| --@1,i2c6--.--.
|............| \'------' \ \ .........
| mctp-i2c- | \ \ \ .mctpB .
| controller | \ \ '.0x30 .
| | \ ......... \ '.......'
| 0x50 | \ .mctpA . \ .........
'------------' '.0x1d . '.mctpC .
'.......' '.0x31 .
'.......'
(mctpX boxes above are remote MCTP devices not included in the DT at
present, they can be hotplugged/probed at runtime. A DT binding for
specific fixed MCTP devices could be added later if required)
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Mon, 15 Nov 2021 02:49:24 +0000 (10:49 +0800)]
i2c: npcm7xx: Allow 255 byte block SMBus transfers
255 byte support has been tested on a npcm750 board
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Patrick Venture <venture@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Mon, 15 Nov 2021 02:49:23 +0000 (10:49 +0800)]
i2c: aspeed: Allow 255 byte block transfers
255 byte transfers have been tested on an AST2500 board
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Mon, 15 Nov 2021 02:49:22 +0000 (10:49 +0800)]
i2c: dev: Handle 255 byte blocks for i2c ioctl
I2C_SMBUS is limited to 32 bytes due to compatibility with the
32 byte i2c_smbus_data.block
I2C_RDWR allows larger transfers if sufficient sized buffers are passed.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Mon, 15 Nov 2021 02:49:21 +0000 (10:49 +0800)]
i2c: core: Allow 255 byte transfers for SMBus 3.x
SMBus 3.0 increased the maximum block transfer size from 32 bytes to
255 bytes. We increase the size of struct i2c_smbus_data's block[]
member.
i2c_smbus_xfer() and i2c_smbus_xfer_emulated() now support 255 byte
block operations, other block functions remain limited to 32 bytes for
compatibility with existing callers.
We allow adapters to indicate support for the larger size with
I2C_FUNC_SMBUS_V3_BLOCK. Most emulated drivers should be able to use 255
byte blocks by replacing I2C_SMBUS_BLOCK_MAX with I2C_SMBUS_V3_BLOCK_MAX
though some will have hardware limitations that need testing.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sun, 14 Nov 2021 19:02:35 +0000 (20:02 +0100)]
net: bridge: Slightly optimize 'find_portno()'
The 'inuse' bitmap is local to this function. So we can use the
non-atomic '__set_bit()' to save a few cycles.
While at it, also remove some useless {}.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Harshit Mogalapalli [Fri, 12 Nov 2021 21:36:47 +0000 (13:36 -0800)]
net: sched: sch_netem: Refactor code in 4-state loss generator
Fixed comments to match description with variable names and
refactored code to match the convention as per [1].
To match the convention mapping is done as follows:
State 3 - LOST_IN_BURST_PERIOD
State 4 - LOST_IN_GAP_PERIOD
[1] S. Salsano, F. Ludovici, A. Ordine, "Definition of a general
and intuitive loss model for packet networks and its implementation
in the Netem module in the Linux kernel"
Fixes:
a6e2fe17eba4 ("sch_netem: replace magic numbers with enumerate")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uwe Kleine-König [Fri, 12 Nov 2021 14:53:52 +0000 (15:53 +0100)]
net: dsa: vsc73xxx: Make vsc73xx_remove() return void
vsc73xx_remove() returns zero unconditionally and no caller checks the
returned value. So convert the function to return no value.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ong Boon Leong [Thu, 11 Nov 2021 14:39:49 +0000 (22:39 +0800)]
net: stmmac: enhance XDP ZC driver level switching performance
The previous stmmac_xdp_set_prog() implementation uses stmmac_release()
and stmmac_open() which tear down the PHY device and causes undesirable
autonegotiation which causes a delay whenever AFXDP ZC is setup.
This patch introduces two new functions that just sufficiently tear
down DMA descriptors, buffer, NAPI process, and IRQs and reestablish
them accordingly in both stmmac_xdp_release() and stammac_xdp_open().
As the results of this enhancement, we get rid of transient state
introduced by the link auto-negotiation:
$ ./xdpsock -i eth0 -t -z
sock0@eth0:0 txonly xdp-drv
pps pkts 1.00
rx 0 0
tx 634444 634560
sock0@eth0:0 txonly xdp-drv
pps pkts 1.00
rx 0 0
tx 632330
1267072
sock0@eth0:0 txonly xdp-drv
pps pkts 1.00
rx 0 0
tx 632438
1899584
sock0@eth0:0 txonly xdp-drv
pps pkts 1.00
rx 0 0
tx 632502
2532160
Reported-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
luo penghao [Thu, 11 Nov 2021 15:09:24 +0000 (15:09 +0000)]
ipv6: Remove duplicate statements
This statement is repeated with the initialization statement
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
luo penghao [Thu, 11 Nov 2021 09:20:47 +0000 (09:20 +0000)]
ipv4: Remove duplicate assignments
there is a same action when the variable is initialized
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
luo penghao [Thu, 11 Nov 2021 09:18:09 +0000 (09:18 +0000)]
ipv4: drop unused assignment
The assignment in the if statement will be overwritten by the
following statement
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 12 Nov 2021 20:35:46 +0000 (12:35 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a boot crash regression"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: api - Fix boot-up crash when crypto manager is disabled
Linus Torvalds [Fri, 12 Nov 2021 20:25:50 +0000 (12:25 -0800)]
Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This series is all the stragglers that didn't quite make the first
merge window pull. It's mostly minor updates and bug fixes of merge
window code but it also has two driver updates: ufs and qla2xxx"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
scsi: scsi_debug: Don't call kcalloc() if size arg is zero
scsi: core: Remove command size deduction from scsi_setup_scsi_cmnd()
scsi: scsi_ioctl: Validate command size
scsi: ufs: ufshpb: Properly handle max-single-cmd
scsi: core: Avoid leaving shost->last_reset with stale value if EH does not run
scsi: bsg: Fix errno when scsi_bsg_register_queue() fails
scsi: sr: Remove duplicate assignment
scsi: ufs: ufs-exynos: Introduce ExynosAuto v9 virtual host
scsi: ufs: ufs-exynos: Multi-host configuration for ExynosAuto v9
scsi: ufs: ufs-exynos: Support ExynosAuto v9 UFS
scsi: ufs: ufs-exynos: Add pre/post_hce_enable drv callbacks
scsi: ufs: ufs-exynos: Factor out priv data init
scsi: ufs: ufs-exynos: Add EXYNOS_UFS_OPT_SKIP_CONFIG_PHY_ATTR option
scsi: ufs: ufs-exynos: Support custom version of ufs_hba_variant_ops
scsi: ufs: ufs-exynos: Add setup_clocks callback
scsi: ufs: ufs-exynos: Add refclkout_stop control
scsi: ufs: ufs-exynos: Simplify drv_data retrieval
scsi: ufs: ufs-exynos: Change pclk available max value
scsi: ufs: Add quirk to enable host controller without PH configuration
scsi: ufs: Add quirk to handle broken UIC command
...
Linus Torvalds [Fri, 12 Nov 2021 20:22:06 +0000 (12:22 -0800)]
Merge tag 'pwm/for-5.16-rc1' of git://git./linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set is mostly small fixes and cleanups, so more of a janitorial
update for this cycle"
* tag 'pwm/for-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: vt8500: Rename pwm_busy_wait() to make it obviously driver-specific
dt-bindings: pwm: tpu: Add R-Car M3-W+ device tree bindings
dt-bindings: pwm: tpu: Add R-Car V3U device tree bindings
pwm: pwm-samsung: Trigger manual update when disabling PWM
pwm: visconti: Simplify using devm_pwmchip_add()
pwm: samsung: Describe driver in Kconfig
pwm: Make it explicit that pwm_apply_state() might sleep
pwm: Add might_sleep() annotations for !CONFIG_PWM API functions
pwm: atmel: Drop unused header
Linus Torvalds [Fri, 12 Nov 2021 20:17:30 +0000 (12:17 -0800)]
Merge tag 'sound-fix-5.16-rc1' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fixes for 5.16-rc1, notably for a few regressions that
were found in 5.15 and pre-rc1:
- revert of the unification of SG-buffer helper functions on x86 and
the relevant fix
- regression fixes for mmap after the recent code refactoring
- two NULL dereference fixes in HD-audio controller driver
- UAF fixes in ALSA timer core
- a few usual HD-audio and FireWire quirks"
* tag 'sound-fix-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fireworks: add support for Loud Onyx 1200f quirk
ALSA: hda: fix general protection fault in azx_runtime_idle
ALSA: hda: Free card instance properly at probe errors
ALSA: hda/realtek: Add quirk for HP EliteBook 840 G7 mute LED
ALSA: memalloc: Remove a stale comment
ALSA: synth: missing check for possible NULL after the call to kstrdup
ALSA: memalloc: Use proper SG helpers for noncontig allocations
ALSA: pci: rme: Fix unaligned buffer addresses
ALSA: firewire-motu: add support for MOTU Track 16
ALSA: PCM: Fix NULL dereference at mmap checks
ALSA: hda/realtek: Add quirk for ASUS UX550VE
ALSA: timer: Unconditionally unlink slave instances, too
ALSA: memalloc: Catch call with NULL snd_dma_buffer pointer
Revert "ALSA: memalloc: Convert x86 SG-buffer handling with non-contiguous type"
ALSA: hda/realtek: Add a quirk for Acer Spin SP513-54N
ALSA: firewire-motu: add support for MOTU Traveler mk3
ALSA: hda/realtek: Headset fixup for Clevo NH77HJQ
ALSA: timer: Fix use-after-free problem
Linus Torvalds [Fri, 12 Nov 2021 20:11:07 +0000 (12:11 -0800)]
Merge tag 'drm-next-2021-11-12' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Dave Airlie:
"I missed a drm-misc-next pull for the main pull last week. It wasn't
that major and isn't the bulk of this at all. This has a bunch of
fixes all over, a lot for amdgpu and i915.
bridge:
- HPD improvments for lt9611uxc
- eDP aux-bus support for ps8640
- LVDS data-mapping selection support
ttm:
- remove huge page functionality (needs reworking)
- fix a race condition during BO eviction
panels:
- add some new panels
fbdev:
- fix double-free
- remove unused scrolling acceleration
- CONFIG_FB dep improvements
locking:
- improve contended locking logging
- naming collision fix
dma-buf:
- add dma_resv_for_each_fence iterator
- fix fence refcounting bug
- name locking fixesA
prime:
- fix object references during mmap
nouveau:
- various code style changes
- refcount fix
- device removal fixes
- protect client list with a mutex
- fix CE0 address calculation
i915:
- DP rates related fixes
- Revert disabling dual eDP that was causing state readout problems
- put the cdclk vtables in const data
- Fix DVO port type for older platforms
- Fix blankscreen by turning DP++ TMDS output buffers on encoder->shutdown
- CCS FBs related fixes
- Fix recursive lock in GuC submission
- Revert guc_id from i915_request tracepoint
- Build fix around dmabuf
amdgpu:
- GPU reset fix
- Aldebaran fix
- Yellow Carp fixes
- DCN2.1 DMCUB fix
- IOMMU regression fix for Picasso
- DSC display fixes
- BPC display calculation fixes
- Other misc display fixes
- Don't allow partial copy from user for DC debugfs
- SRIOV fixes
- GFX9 CSB pin count fix
- Various IP version check fixes
- DP 2.0 fixes
- Limit DCN1 MPO fix to DCN1
amdkfd:
- SVM fixes
- Fix gfx version for renoir
- Reset fixes
udl:
- timeout fix
imx:
- circular locking fix
virtio:
- NULL ptr deref fix"
* tag 'drm-next-2021-11-12' of git://anongit.freedesktop.org/drm/drm: (126 commits)
drm/ttm: Double check mem_type of BO while eviction
drm/amdgpu: add missed support for UVD IP_VERSION(3, 0, 64)
drm/amdgpu: drop jpeg IP initialization in SRIOV case
drm/amd/display: reject both non-zero src_x and src_y only for DCN1x
drm/amd/display: Add callbacks for DMUB HPD IRQ notifications
drm/amd/display: Don't lock connection_mutex for DMUB HPD
drm/amd/display: Add comment where CONFIG_DRM_AMD_DC_DCN macro ends
drm/amdkfd: Fix retry fault drain race conditions
drm/amdkfd: lower the VAs base offset to 8KB
drm/amd/display: fix exit from amdgpu_dm_atomic_check() abruptly
drm/amd/amdgpu: fix the kfd pre_reset sequence in sriov
drm/amdgpu: fix uvd crash on Polaris12 during driver unloading
drm/i915/adlp/fb: Prevent the mapping of redundant trailing padding NULL pages
drm/i915/fb: Fix rounding error in subsampled plane size calculation
drm/i915/hdmi: Turn DP++ TMDS output buffers back on in encoder->shutdown()
drm/locking: fix __stack_depot_* name conflict
drm/virtio: Fix NULL dereference error in virtio_gpu_poll
drm/amdgpu: fix SI handling in amdgpu_device_asic_has_dc_support()
drm/amdgpu: Fix dangling kfd_bo pointer for shared BOs
drm/amd/amdkfd: Don't sent command to HWS on kfd reset
...
Linus Torvalds [Fri, 12 Nov 2021 19:53:16 +0000 (11:53 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Just one new driver (Cypress StreetFighter touchkey), and no input
core changes this time.
Plus various fixes and enhancements to existing drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: iforce - fix control-message timeout
Input: wacom_i2c - use macros for the bit masks
Input: ili210x - reduce sample period to 15ms
Input: ili210x - improve polled sample spacing
Input: ili210x - special case ili251x sample read out
Input: elantench - fix misreporting trackpoint coordinates
Input: synaptics-rmi4 - Fix device hierarchy
Input: i8042 - Add quirk for Fujitsu Lifebook T725
Input: cap11xx - add support for cap1206
Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
Input: ili210x - add ili251x firmware update support
Input: ili210x - export ili251x version details via sysfs
Input: ili210x - use resolution from ili251x firmware
Input: pm8941-pwrkey - respect reboot_mode for warm reset
reboot: export symbol 'reboot_mode'
Input: max77693-haptic - drop unneeded MODULE_ALIAS
Input: cpcap-pwrbutton - do not set input parent explicitly
Input: max8925_onkey - don't mark comment as kernel-doc
Input: ads7846 - do not attempt IRQ workaround when deferring probe
Input: ads7846 - use input_set_capability()
...
Linus Torvalds [Fri, 12 Nov 2021 19:44:31 +0000 (11:44 -0800)]
Merge tag 'rtc-5.16' of git://git./linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"This includes new ioctls to get and set parameters and in particular
the backup switch mode that is needed for some RTCs to actually enable
the backup voltage (and have a useful RTC).
The same interface can also be used to get the actual features
supported by the RTC so userspace has a better way than trying and
failing.
Summary:
Subsystem:
- Add new ioctl to get and set extra RTC parameters, this includes
backup switch mode
- Expose available features to userspace, in particular, when alarmas
have a resolution of one minute instead of a second.
- Let the core handle those alarms with a minute resolution
New driver:
- MSTAR MSC313 RTC
Drivers:
- Add SPI ID table where necessary
- Add BSM support for rv3028, rv3032 and pcf8523
- s3c: set RTC range
- rx8025: set range, implement .set_offset and .read_offset"
* tag 'rtc-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
rtc: rx8025: use .set_offset/.read_offset
rtc: rx8025: use rtc_add_group
rtc: rx8025: clear RTC_FEATURE_ALARM when alarm are not supported
rtc: rx8025: set range
rtc: rx8025: let the core handle the alarm resolution
rtc: rx8025: switch to devm_rtc_allocate_device
rtc: ab8500: let the core handle the alarm resolution
rtc: ab-eoz9: support UIE when available
rtc: ab-eoz9: use RTC_FEATURE_UPDATE_INTERRUPT
rtc: rv3032: let the core handle the alarm resolution
rtc: s35390a: let the core handle the alarm resolution
rtc: handle alarms with a minute resolution
rtc: pcf85063: silence cppcheck warning
rtc: rv8803: fix writing back ctrl in flag register
rtc: s3c: Add time range
rtc: s3c: Extract read/write IO into separate functions
rtc: s3c: Remove usage of devm_rtc_device_register()
rtc: tps80031: Remove driver
rtc: sun6i: Allow probing without an early clock provider
rtc: pcf8523: add BSM support
...
Linus Torvalds [Fri, 12 Nov 2021 19:32:22 +0000 (11:32 -0800)]
Merge tag 'libata-5.16-rc1-p2' of git://git./linux/kernel/git/dlemoal/libata
Pull more libata updates from Damien Le Moal:
"Second round of updates for libata for 5.16:
- Fix READ LOG EXT and READ LOG DMA EXT command timeouts during disk
revalidation after a resume or a modprobe of the LLDD (me)
- Remove unnecessary error message in sata_highbank driver (Xu)
- Better handling of accesses to the IDENTIFY DEVICE data log for
drives that do not support this log page (me)
- Fix ahci_shost_attr_group declaration in ahci driver (me)"
* tag 'libata-5.16-rc1-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
libata: libahci: declare ahci_shost_attr_group as static
libata: add horkage for missing Identify Device log
ata: sata_highbank: Remove unnecessary print function dev_err()
libata: fix read log timeout value
Sasha Levin [Fri, 12 Nov 2021 15:16:02 +0000 (10:16 -0500)]
tools/lib/lockdep: drop liblockdep
TL;DR: While a tool like liblockdep is useful, it probably doesn't
belong within the kernel tree.
liblockdep attempts to reuse kernel code both directly (by directly
building the kernel's lockdep code) as well as indirectly (by using
sanitized headers). This makes liblockdep an integral part of the
kernel.
It also makes liblockdep quite unique: while other userspace code might
use sanitized headers, it generally doesn't attempt to use kernel code
directly which means that changes on the kernel side of things don't
affect (and break) it directly.
All our workflows and tooling around liblockdep don't support this
uniqueness. Changes that go into the kernel code aren't validated to not
break in-tree userspace code.
liblockdep ended up being very fragile, breaking over and over, to the
point that living in the same tree as the lockdep code lost most of it's
value.
liblockdep should continue living in an external tree, syncing with
the kernel often, in a controllable way.
Signed-off-by: Sasha Levin <sashal@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 12 Nov 2021 18:56:25 +0000 (10:56 -0800)]
thermal: int340x: fix build on 32-bit targets
Commit
aeb58c860dc5 ("thermal/drivers/int340x: processor_thermal: Suppot
64 bit RFIM responses") started using 'readq()' to read 64-bit status
responses from the int340x hardware.
That's all fine and good, but on 32-bit targets a 64-bit 'readq()' is
ambiguous, since it's no longer an atomic access. Some hardware might
require 64-bit accesses, and other hardware might want low word first or
high word first.
It's quite likely that the driver isn't relevant in a 32-bit environment
any more, and there's a patch floating around to just make it depend on
X86_64, but let's make it buildable on x86-32 anyway.
The driver previously just read the low 32 bits, so the hardware
certainly is ok with 32-bit reads, and in a little-endian environment
the low word first model is the natural one.
So just add the include for the 'io-64-nonatomic-lo-hi.h' version.
Fixes:
aeb58c860dc5 ("thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dmitry Torokhov [Fri, 12 Nov 2021 05:58:54 +0000 (21:58 -0800)]
Merge branch 'next' into for-linus
Prepare input updates for 5.16 merge window.
Dave Airlie [Fri, 12 Nov 2021 03:06:37 +0000 (13:06 +1000)]
Merge tag 'drm-misc-fixes-2021-11-11' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
* dma-buf: name_lock fixes
* prime: Keep object ref during mmap
* nouveau: Fix a refcount issue; Fix device removal; Protect client
list with dedicated mutex; Fix address CE0 address calculation
* ttm: Fix race condition during BO eviction
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YYzY6jeox9EeI15i@linux-uq9g.fritz.box
Dave Airlie [Thu, 11 Nov 2021 23:22:28 +0000 (09:22 +1000)]
BackMerge tag 'v5.15' into drm-next
I got a drm-fixes which had some 5.15 stuff in it, so to avoid
the mess just backmerge here.
Linux 5.15
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 11 Nov 2021 23:10:18 +0000 (15:10 -0800)]
Merge tag 'pci-v5.16-fixes-1' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Revert conversion to struct device.driver instead of struct
pci_dev.driver.
The device.driver is set earlier, and using it caused the PCI core to
call driver PM entry points before .probe() and after .remove(), when
the driver isn't prepared.
This caused NULL pointer dereferences in i2c_designware_pci and
probably other driver issues"
* tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Use to_pci_driver() instead of pci_dev->driver"
Revert "PCI: Remove struct pci_dev->driver"
Damien Le Moal [Thu, 11 Nov 2021 03:03:27 +0000 (12:03 +0900)]
libata: libahci: declare ahci_shost_attr_group as static
ahci_shost_attr_group is referenced only in drivers/ata/libahci.c.
Declare it as static.
Fixes:
c3f69c7f629f ("scsi: ata: Switch to attribute groups")
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Damien Le Moal [Mon, 8 Nov 2021 23:45:25 +0000 (08:45 +0900)]
libata: add horkage for missing Identify Device log
ACS-3 introduced the ATA Identify Device Data log as mandatory. A
warning message currently signals to the user if a device does not
report supporting this log page in the log directory page, regardless
of the ATA version of the device. Furthermore, this warning will appear
for all attempts at accessing this missing log page during device
revalidation.
Since it is useless to constantly access the log directory and warn
about this lack of support once we have discovered that the device
does not support this log page, introduce the horkage flag
ATA_HORKAGE_NO_ID_DEV_LOG to mark a device as lacking support for
the Identify Device Data log page. Set this flag when
ata_log_supported() returns false in ata_identify_page_supported().
The warning is printed only if the device ATA level is 10 or above
(ACS-3 or above), and only once on device scan. With this flag set, the
log directory page is not accessed again to test for Identify Device
Data log page support.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Linus Torvalds [Thu, 11 Nov 2021 23:00:04 +0000 (15:00 -0800)]
Merge tag 'kcsan.2021.11.11a' of git://git./linux/kernel/git/paulmck/linux-rcu
Pull KCSAN updates from Paul McKenney:
"This contains initialization fixups, testing improvements, addition of
instruction pointer to data-race reports, and scoped data-race checks"
* tag 'kcsan.2021.11.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
kcsan: selftest: Cleanup and add missing __init
kcsan: Move ctx to start of argument list
kcsan: Support reporting scoped read-write access type
kcsan: Start stack trace with explicit location if provided
kcsan: Save instruction pointer for scoped accesses
kcsan: Add ability to pass instruction pointer of access to reporting
kcsan: test: Fix flaky test case
kcsan: test: Use kunit_skip() to skip tests
kcsan: test: Defer kcsan_test_init() after kunit initialization
Linus Torvalds [Thu, 11 Nov 2021 22:47:32 +0000 (14:47 -0800)]
Merge tag 'apparmor-pr-2021-11-10' of git://git./linux/kernel/git/jj/linux-apparmor
Pull apparmor updates from John Johansen:
"Features
- use per file locks for transactional queries
- update policy management capability checks to work with LSM stacking
Bug Fixes:
- check/put label on apparmor_sk_clone_security()
- fix error check on update of label hname
- fix introspection of of task mode for unconfined tasks
Cleanups:
- avoid -Wempty-body warning
- remove duplicated 'Returns:' comments
- fix doc warning
- remove unneeded one-line hook wrappers
- use struct_size() helper in kzalloc()
- fix zero-length compiler warning in AA_BUG()
- file.h: delete duplicated word
- delete repeated words in comments
- remove repeated declaration"
* tag 'apparmor-pr-2021-11-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: remove duplicated 'Returns:' comments
apparmor: remove unneeded one-line hook wrappers
apparmor: Use struct_size() helper in kzalloc()
apparmor: fix zero-length compiler warning in AA_BUG()
apparmor: use per file locks for transactional queries
apparmor: fix doc warning
apparmor: Remove the repeated declaration
apparmor: avoid -Wempty-body warning
apparmor: Fix internal policy capable check for policy management
apparmor: fix error check
security: apparmor: delete repeated words in comments
security: apparmor: file.h: delete duplicated word
apparmor: switch to apparmor to internal capable check for policy management
apparmor: update policy capable checks to use a label
apparmor: fix introspection of of task mode for unconfined tasks
apparmor: check/put label on apparmor_sk_clone_security()
Linus Torvalds [Thu, 11 Nov 2021 22:31:47 +0000 (14:31 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge more updates from Andrew Morton:
"The post-linux-next material.
7 patches.
Subsystems affected by this patch series (all mm): debug,
slab-generic, migration, memcg, and kasan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kasan: add kasan mode messages when kasan init
mm: unexport {,un}lock_page_memcg
mm: unexport folio_memcg_{,un}lock
mm/migrate.c: remove MIGRATE_PFN_LOCKED
mm: migrate: simplify the file-backed pages validation when migrating its mapping
mm: allow only SLUB on PREEMPT_RT
mm/page_owner.c: modify the type of argument "order" in some functions
Linus Torvalds [Thu, 11 Nov 2021 22:22:05 +0000 (14:22 -0800)]
Merge tag 'm68knommu-for-v5.16' of git://git./linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"Only two changes.
One removes the now unused CONFIG_MCPU32 symbol. The other sets a
default for the CONFIG_MEMORY_RESERVE config symbol (this aids
scripting and other automation) so you don't interactively get asked
for a value at configure time.
Summary:
- remove unused CONFIG_MCPU32 symbol
- default CONFIG_MEMORY_RESERVE value (for scripting)"
* tag 'm68knommu-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: Remove MCPU32 config symbol
m68k: set a default value for MEMORY_RESERVE
Bjorn Helgaas [Wed, 10 Nov 2021 18:03:34 +0000 (12:03 -0600)]
Revert "PCI: Use to_pci_driver() instead of pci_dev->driver"
This reverts commit
2a4d9408c9e8b6f6fc150c66f3fef755c9e20d4a.
Robert reported a NULL pointer dereference caused by the PCI core
(local_pci_probe()) calling the i2c_designware_pci driver's
.runtime_resume() method before the .probe() method. i2c_dw_pci_resume()
depends on initialization done by i2c_dw_pci_probe().
Prior to
2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of
pci_dev->driver"), pci_pm_runtime_resume() avoided calling the
.runtime_resume() method because pci_dev->driver had not been set yet.
2a4d9408c9e8 and
b5f9c644eb1b ("PCI: Remove struct pci_dev->driver"),
removed pci_dev->driver, replacing it by device->driver, which *has* been
set by this time, so pci_pm_runtime_resume() called the .runtime_resume()
method when it previously had not.
Fixes:
2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bjorn Helgaas [Wed, 10 Nov 2021 18:01:14 +0000 (12:01 -0600)]
Revert "PCI: Remove struct pci_dev->driver"
This reverts commit
b5f9c644eb1baafcd349ad134e2110773f8d0a38.
Revert
b5f9c644eb1b ("PCI: Remove struct pci_dev->driver"), which is needed
to revert
2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of
pci_dev->driver").
2a4d9408c9e8 caused a NULL pointer dereference reported by Robert Święcki.
Details in the revert of that commit.
Fixes:
2a4d9408c9e8 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Linus Torvalds [Thu, 11 Nov 2021 18:16:33 +0000 (10:16 -0800)]
Merge tag 'trace-v5.16-3' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two locking fixes:
- Add mutex protection to ring_buffer_reset()
- Fix deadlock in modify_ftrace_direct_multi()"
* tag 'trace-v5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/direct: Fix lockup in modify_ftrace_direct_multi
ring-buffer: Protect ring_buffer_reset() from reentrancy
Linus Torvalds [Thu, 11 Nov 2021 17:49:36 +0000 (09:49 -0800)]
Merge tag 'net-5.16-rc1' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- bpf: do not reject when the stack read size is different from the
tracked scalar size
- net: fix premature exit from NAPI state polling in napi_disable()
- riscv, bpf: fix RV32 broken build, and silence RV64 warning
Current release - new code bugs:
- net: fix possible NULL deref in sock_reserve_memory
- amt: fix error return code in amt_init(); fix stopping the
workqueue
- ax88796c: use the correct ioctl callback
Previous releases - always broken:
- bpf: stop caching subprog index in the bpf_pseudo_func insn
- security: fixups for the security hooks in sctp
- nfc: add necessary privilege flags in netlink layer, limit
operations to admin only
- vsock: prevent unnecessary refcnt inc for non-blocking connect
- net/smc: fix sk_refcnt underflow on link down and fallback
- nfnetlink_queue: fix OOB when mac header was cleared
- can: j1939: ignore invalid messages per standard
- bpf, sockmap:
- fix race in ingress receive verdict with redirect to self
- fix incorrect sk_skb data_end access when src_reg = dst_reg
- strparser, and tls are reusing qdisc_skb_cb and colliding
- ethtool: fix ethtool msg len calculation for pause stats
- vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries to
access an unregistering real_dev
- udp6: make encap_rcv() bump the v6 not v4 stats
- drv: prestera: add explicit padding to fix m68k build
- drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge
- drv: mvpp2: fix wrong SerDes reconfiguration order
Misc & small latecomers:
- ipvs: auto-load ipvs on genl access
- mctp: sanity check the struct sockaddr_mctp padding fields
- libfs: support RENAME_EXCHANGE in simple_rename()
- avoid double accounting for pure zerocopy skbs"
* tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (123 commits)
selftests/net: udpgso_bench_rx: fix port argument
net: wwan: iosm: fix compilation warning
cxgb4: fix eeprom len when diagnostics not implemented
net: fix premature exit from NAPI state polling in napi_disable()
net/smc: fix sk_refcnt underflow on linkdown and fallback
net/mlx5: Lag, fix a potential Oops with mlx5_lag_create_definer()
gve: fix unmatched u64_stats_update_end()
net: ethernet: lantiq_etop: Fix compilation error
selftests: forwarding: Fix packet matching in mirroring selftests
vsock: prevent unnecessary refcnt inc for nonblocking connect
net: marvell: mvpp2: Fix wrong SerDes reconfiguration order
net: ethernet: ti: cpsw_ale: Fix access to un-initialized memory
net: stmmac: allow a tc-taprio base-time of zero
selftests: net: test_vxlan_under_vrf: fix HV connectivity test
net: hns3: allow configure ETS bandwidth of all TCs
net: hns3: remove check VF uc mac exist when set by PF
net: hns3: fix some mac statistics is always 0 in device version V2
net: hns3: fix kernel crash when unload VF while it is being reset
net: hns3: sync rx ring head in echo common pull
net: hns3: fix pfc packet number incorrect after querying pfc parameters
...
Linus Torvalds [Thu, 11 Nov 2021 17:44:29 +0000 (09:44 -0800)]
Merge tag 'char-misc-5.16-rc1' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc fix from Greg KH:
"Here is a single fix for 5.16-rc1 to resolve a build problem that came
in through the coresight tree (and as such came in through the
char/misc tree merge in the 5.16-rc1 merge window).
It resolves a build problem with 'allmodconfig' on arm64 and is acked
by the proper subsystem maintainers. It has been in linux-next all
week with no reported problems"
* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
arm64: cpufeature: Export this_cpu_has_cap helper
Linus Torvalds [Thu, 11 Nov 2021 17:40:15 +0000 (09:40 -0800)]
Merge tag 'usb-5.16-rc1' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small reverts and fixes for USB drivers for issues that
came up during the 5.16-rc1 merge window.
These include:
- two reverts of xhci and USB core patches that are causing problems
in many systems.
- xhci 3.1 enumeration delay fix for systems that were having
problems.
All three of these have been in linux-next all week with no reported
issues"
* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Fix USB 3.1 enumeration issues by increasing roothub power-on-good delay
Revert "usb: core: hcd: Add support for deferring roothub registration"
Revert "xhci: Set HCD flag to defer primary roothub registration"
Kuan-Ying Lee [Thu, 11 Nov 2021 04:32:49 +0000 (20:32 -0800)]
kasan: add kasan mode messages when kasan init
There are multiple kasan modes. It makes sense that we add some
messages to know which kasan mode is active when booting up [1].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=212195
Link: https://lkml.kernel.org/r/20211020094850.4113-1-Kuan-Ying.Lee@mediatek.com
Signed-off-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Reviewed-by: Marco Elver <elver@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: Yee Lee <yee.lee@mediatek.com>
Cc: Nicholas Tang <nicholas.tang@mediatek.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Thu, 11 Nov 2021 04:32:46 +0000 (20:32 -0800)]
mm: unexport {,un}lock_page_memcg
These are only used in built-in core mm code.
Link: https://lkml.kernel.org/r/20210820095815.445392-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig [Thu, 11 Nov 2021 04:32:43 +0000 (20:32 -0800)]
mm: unexport folio_memcg_{,un}lock
Patch series "unexport memcg locking helpers".
Neither the old page-based nor the new folio-based memcg locking helpers
are used in modular code at all, so drop the exports.
This patch (of 2):
folio_memcg_{,un}lock are only used in built-in core mm code.
Link: https://lkml.kernel.org/r/20210820095815.445392-1-hch@lst.de
Link: https://lkml.kernel.org/r/20210820095815.445392-2-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alistair Popple [Thu, 11 Nov 2021 04:32:40 +0000 (20:32 -0800)]
mm/migrate.c: remove MIGRATE_PFN_LOCKED
MIGRATE_PFN_LOCKED is used to indicate to migrate_vma_prepare() that a
source page was already locked during migrate_vma_collect(). If it
wasn't then the a second attempt is made to lock the page. However if
the first attempt failed it's unlikely a second attempt will succeed,
and the retry adds complexity. So clean this up by removing the retry
and MIGRATE_PFN_LOCKED flag.
Destination pages are also meant to have the MIGRATE_PFN_LOCKED flag
set, but nothing actually checks that.
Link: https://lkml.kernel.org/r/20211025041608.289017-1-apopple@nvidia.com
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Baolin Wang [Thu, 11 Nov 2021 04:32:37 +0000 (20:32 -0800)]
mm: migrate: simplify the file-backed pages validation when migrating its mapping
There is no need to validate the file-backed page's refcount before
trying to freeze the page's expected refcount, instead we can rely on
the folio_ref_freeze() to validate if the page has the expected refcount
before migrating its mapping.
Moreover we are always under the page lock when migrating the page
mapping, which means nowhere else can remove it from the page cache, so
we can remove the xas_load() validation under the i_pages lock.
Link: https://lkml.kernel.org/r/cover.1629447552.git.baolin.wang@linux.alibaba.com
Link: https://lkml.kernel.org/r/df4c129fd8e86a95dbc55f4663d77441cc0d3bd1.1629447552.git.baolin.wang@linux.alibaba.com
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Suggested-by: Matthew Wilcox <willy@infradead.org>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Alistair Popple <apopple@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Molnar [Thu, 11 Nov 2021 04:32:33 +0000 (20:32 -0800)]
mm: allow only SLUB on PREEMPT_RT
Memory allocators may disable interrupts or preemption as part of the
allocation and freeing process. For PREEMPT_RT it is important that
these sections remain deterministic and short and therefore don't depend
on the size of the memory to allocate/ free or the inner state of the
algorithm.
Until v3.12-RT the SLAB allocator was an option but involved several
changes to meet all the requirements. The SLUB design fits better with
PREEMPT_RT model and so the SLAB patches were dropped in the 3.12-RT
patchset. Comparing the two allocator, SLUB outperformed SLAB in both
throughput (time needed to allocate and free memory) and the maximal
latency of the system measured with cyclictest during hackbench.
SLOB was never evaluated since it was unlikely that it preforms better
than SLAB. During a quick test, the kernel crashed with SLOB enabled
during boot.
Disable SLAB and SLOB on PREEMPT_RT.
[bigeasy@linutronix.de: commit description]
Link: https://lkml.kernel.org/r/20211015210336.gen3tib33ig5q2md@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yixuan Cao [Thu, 11 Nov 2021 04:32:30 +0000 (20:32 -0800)]
mm/page_owner.c: modify the type of argument "order" in some functions
The type of "order" in struct page_owner is unsigned short.
However, it is unsigned int in the following 3 functions:
__reset_page_owner
__set_page_owner_handle
__set_page_owner_handle
The type of "order" in argument list is unsigned int, which is
inconsistent.
[akpm@linux-foundation.org: update include/linux/page_owner.h]
Link: https://lkml.kernel.org/r/20211020125945.47792-1-caoyixuan2019@email.szu.edu.cn
Signed-off-by: Yixuan Cao <caoyixuan2019@email.szu.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Sakamoto [Thu, 11 Nov 2021 10:30:15 +0000 (19:30 +0900)]
ALSA: fireworks: add support for Loud Onyx 1200f quirk
Loud Technologies shipped Onyx 1200f 2008 in its Mackie brand and
already discontinued. The model uses component of Fireworks board
module as its communication and DSP function.
The latest firmware (v4.6.0) has a quirk that tx packet includes wrong
value (0x1f) in its dbs field at middle and higher sampling transfer
frequency. It brings ALSA fireworks driver discontinuity of data block
counter.
This commit fixes it by assuming it as a quirk of firmware version
4.6.0.
$ cd linux-firewire-tools/src
$ python crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400
0404b9ef bus_info_length 4, crc_length 4, crc 47599
404
31333934 bus_name "1394"
408
e064a212 irmc 1, cmc 1, isc 1, bmc 0, pmc 0, cyc_clk_acc 100,
max_rec 10 (2048), max_rom 2, gen 1, spd 2 (S400)
40c
000ff209 company_id 000ff2 |
410
62550ce0 device_id
0962550ce0 | EUI-64
000ff20962550ce0
root directory
-----------------------------------------------------------------
414
0008088e directory_length 8, crc 2190
418
03000ff2 vendor
41c
8100000f --> descriptor leaf at 458
420
1701200f model
424
81000018 --> descriptor leaf at 484
428
0c008380 node capabilities
42c
8d000003 --> eui-64 leaf at 438
430
d1000005 --> unit directory at 444
434
08000ff2 (immediate value)
eui-64 leaf at 438
-----------------------------------------------------------------
438
000281ae leaf_length 2, crc 33198
43c
000ff209 company_id 000ff2 |
440
62550ce0 device_id
0962550ce0 | EUI-64
000ff20962550ce0
unit directory at 444
-----------------------------------------------------------------
444
00045d94 directory_length 4, crc 23956
448
1200a02d specifier id: 1394 TA
44c
13010000 version
450
1701200f model
454
8100000c --> descriptor leaf at 484
descriptor leaf at 458
-----------------------------------------------------------------
458
000a199d leaf_length 10, crc 6557
45c
00000000 textual descriptor
460
00000000 minimal ASCII
464
4d61636b "Mack"
468
69650000 "ie"
46c
00000000
470
00000000
474
00000000
478
00000000
47c
00000000
480
00000000
descriptor leaf at 484
-----------------------------------------------------------------
484
000a0964 leaf_length 10, crc 2404
488
00000000 textual descriptor
48c
00000000 minimal ASCII
490
4f6e7978 "Onyx"
494
20313230 " 120"
498
30460000 "0F"
49c
00000000
4a0
00000000
4a4
00000000
4a8
00000000
4ac
00000000
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20211111103015.7498-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Willem de Bruijn [Thu, 11 Nov 2021 11:57:17 +0000 (06:57 -0500)]
selftests/net: udpgso_bench_rx: fix port argument
The below commit added optional support for passing a bind address.
It configures the sockaddr bind arguments before parsing options and
reconfigures on options -b and -4.
This broke support for passing port (-p) on its own.
Configure sockaddr after parsing all arguments.
Fixes:
3327a9c46352 ("selftests: add functionals test for UDP GRO")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Wed, 10 Nov 2021 16:20:36 +0000 (21:50 +0530)]
net: wwan: iosm: fix compilation warning
curr_phase is unused. Removed the dead code.
Fixes:
8d9be0634181 ("net: wwan: iosm: transport layer support for fw flashing/cd")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Thu, 11 Nov 2021 10:25:16 +0000 (15:55 +0530)]
cxgb4: fix eeprom len when diagnostics not implemented
Ensure diagnostics monitoring support is implemented for the SFF 8472
compliant port module and set the correct length for ethtool port
module eeprom read.
Fixes:
f56ec6766dcf ("cxgb4: Add support for ethtool i2c dump")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xinhui pan [Wed, 10 Nov 2021 04:31:49 +0000 (12:31 +0800)]
drm/ttm: Double check mem_type of BO while eviction
BO might sit in a wrong lru list as there is a small period of memory
moving and lru list updating.
Lets skip eviction if we hit such mismatch.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211110043149.57554-2-xinhui.pan@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Xu Wang [Fri, 5 Nov 2021 01:50:21 +0000 (01:50 +0000)]
ata: sata_highbank: Remove unnecessary print function dev_err()
The print function dev_err() is redundant because
platform_get_irq() already prints an error.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Damien Le Moal [Thu, 4 Nov 2021 08:31:58 +0000 (17:31 +0900)]
libata: fix read log timeout value
Some ATA drives are very slow to respond to READ_LOG_EXT and
READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the
device is revalidated right after resuming a system or inserting the
ATA adapter driver (e.g. ahci). The default 5s timeout
(ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing
errors during the device configuration. Ex:
...
ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: ATA-9: XXX XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133
ata9.00: qc timeout (cmd 0x2f)
ata9.00: Read log page 0x00 failed, Emask 0x4
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: NCQ Send/Recv Log not supported
ata9.00: Read log page 0x08 failed, Emask 0x40
ata9.00:
27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: ATA Identify Device Log not supported
ata9.00: failed to set xfermode (err_mask=0x40)
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: configured for UDMA/133
...
The timeout error causes a soft reset of the drive link, followed in
most cases by a successful revalidation as that give enough time to the
drive to become fully ready to quickly process the read log commands.
However, in some cases, this also fails resulting in the device being
dropped.
Fix this by using adding the ata_eh_revalidate_timeouts entries for the
READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout
increased to 15s, retriable one time.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Alexander Lobakin [Wed, 10 Nov 2021 19:56:05 +0000 (20:56 +0100)]
net: fix premature exit from NAPI state polling in napi_disable()
Commit
719c57197010 ("net: make napi_disable() symmetric with
enable") accidentally introduced a bug sometimes leading to a kernel
BUG when bringing an iface up/down under heavy traffic load.
Prior to this commit, napi_disable() was polling n->state until
none of (NAPIF_STATE_SCHED | NAPIF_STATE_NPSVC) is set and then
always flip them. Now there's a possibility to get away with the
NAPIF_STATE_SCHE unset as 'continue' drops us to the cmpxchg()
call with an uninitialized variable, rather than straight to
another round of the state check.
Error path looks like:
napi_disable():
unsigned long val, new; /* new is uninitialized */
do {
val = READ_ONCE(n->state); /* NAPIF_STATE_NPSVC and/or
NAPIF_STATE_SCHED is set */
if (val & (NAPIF_STATE_SCHED | NAPIF_STATE_NPSVC)) { /* true */
usleep_range(20, 200);
continue; /* go straight to the condition check */
}
new = val | <...>
} while (cmpxchg(&n->state, val, new) != val); /* state == val, cmpxchg()
writes garbage */
napi_enable():
do {
val = READ_ONCE(n->state);
BUG_ON(!test_bit(NAPI_STATE_SCHED, &val)); /* 50/50 boom */
<...>
while the typical BUG splat is like:
[ 172.652461] ------------[ cut here ]------------
[ 172.652462] kernel BUG at net/core/dev.c:6937!
[ 172.656914] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[ 172.661966] CPU: 36 PID: 2829 Comm: xdp_redirect_cp Tainted: G I 5.15.0 #42
[ 172.670222] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0014.
082620210524 08/26/2021
[ 172.680646] RIP: 0010:napi_enable+0x5a/0xd0
[ 172.684832] Code: 07 49 81 cc 00 01 00 00 4c 89 e2 48 89 d8 80 e6 fb f0 48 0f b1 55 10 48 39 c3 74 10 48 8b 5d 10 f6 c7 04 75 3d f6 c3 01 75 b4 <0f> 0b 5b 5d 41 5c c3 65 ff 05 b8 e5 61 53 48 c7 c6 c0 f3 34 ad 48
[ 172.703578] RSP: 0018:
ffffa3c9497477a8 EFLAGS:
00010246
[ 172.708803] RAX:
ffffa3c96615a014 RBX:
0000000000000000 RCX:
ffff8a4b575301a0
< snip >
[ 172.782403] Call Trace:
[ 172.784857] <TASK>
[ 172.786963] ice_up_complete+0x6f/0x210 [ice]
[ 172.791349] ice_xdp+0x136/0x320 [ice]
[ 172.795108] ? ice_change_mtu+0x180/0x180 [ice]
[ 172.799648] dev_xdp_install+0x61/0xe0
[ 172.803401] dev_xdp_attach+0x1e0/0x550
[ 172.807240] dev_change_xdp_fd+0x1e6/0x220
[ 172.811338] do_setlink+0xee8/0x1010
[ 172.814917] rtnl_setlink+0xe5/0x170
[ 172.818499] ? bpf_lsm_binder_set_context_mgr+0x10/0x10
[ 172.823732] ? security_capable+0x36/0x50
< snip >
Fix this by replacing 'do { } while (cmpxchg())' with an "infinite"
for-loop with an explicit break.
From v1 [0]:
- just use a for-loop to simplify both the fix and the existing
code (Eric).
[0] https://lore.kernel.org/netdev/
20211110191126.1214-1-alexandr.lobakin@intel.com
Fixes:
719c57197010 ("net: make napi_disable() symmetric with enable")
Suggested-by: Eric Dumazet <edumazet@google.com> # for-loop
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211110195605.1304-1-alexandr.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 11 Nov 2021 01:05:37 +0000 (17:05 -0800)]
Merge tag 'ext4_for_linus' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"Only bug fixes and cleanups for ext4 this merge window.
Of note are fixes for the combination of the inline_data and
fast_commit fixes, and more accurately calculating when to schedule
additional lazy inode table init, especially when CONFIG_HZ is 100HZ"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix error code saved on super block during file system abort
ext4: inline data inode fast commit replay fixes
ext4: commit inline data during fast commit
ext4: scope ret locally in ext4_try_to_trim_range()
ext4: remove an unused variable warning with CONFIG_QUOTA=n
ext4: fix boolreturn.cocci warnings in fs/ext4/name.c
ext4: prevent getting empty inode buffer
ext4: move ext4_fill_raw_inode() related functions
ext4: factor out ext4_fill_raw_inode()
ext4: prevent partial update of the extent blocks
ext4: check for inconsistent extents between index and leaf block
ext4: check for out-of-order index extents in ext4_valid_extent_entries()
ext4: convert from atomic_t to refcount_t on ext4_io_end->count
ext4: refresh the ext4_ext_path struct after dropping i_data_sem.
ext4: ensure enough credits in ext4_ext_shift_path_extents
ext4: correct the left/middle/right debug message for binsearch
ext4: fix lazy initialization next schedule time computation in more granular unit
Revert "ext4: enforce buffer head state assertion in ext4_da_map_blocks"
Linus Torvalds [Thu, 11 Nov 2021 00:50:57 +0000 (16:50 -0800)]
Merge tag 'for-5.16-deadlock-fix-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"Fix for a deadlock when direct/buffered IO is done on a mmaped file
and a fault happens (details in the patch). There's a fstest
generic/647 that triggers the problem and makes testing hard"
* tag 'for-5.16-deadlock-fix-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix deadlock due to page faults during direct IO reads and writes
Linus Torvalds [Thu, 11 Nov 2021 00:45:54 +0000 (16:45 -0800)]
Merge tag 'nfsd-5.16' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"A slow cycle for nfsd: mainly cleanup, including Neil's patch dropping
support for a filehandle format deprecated 20 years ago, and further
xdr-related cleanup from Chuck"
* tag 'nfsd-5.16' of git://linux-nfs.org/~bfields/linux: (26 commits)
nfsd4: remove obselete comment
nfsd: document server-to-server-copy parameters
NFSD:fix boolreturn.cocci warning
nfsd: update create verifier comment
SUNRPC: Change return value type of .pc_encode
SUNRPC: Replace the "__be32 *p" parameter to .pc_encode
NFSD: Save location of NFSv4 COMPOUND status
SUNRPC: Change return value type of .pc_decode
SUNRPC: Replace the "__be32 *p" parameter to .pc_decode
SUNRPC: De-duplicate .pc_release() call sites
SUNRPC: Simplify the SVC dispatch code path
SUNRPC: Capture value of xdr_buf::page_base
SUNRPC: Add trace event when alloc_pages_bulk() makes no progress
svcrdma: Split svcrmda_wc_{read,write} tracepoints
svcrdma: Split the svcrdma_wc_send() tracepoint
svcrdma: Split the svcrdma_wc_receive() tracepoint
NFSD: Have legacy NFSD WRITE decoders use xdr_stream_subsegment()
SUNRPC: xdr_stream_subsegment() must handle non-zero page_bases
NFSD: Initialize pointer ni with NULL and not plain integer 0
NFSD: simplify struct nfsfh
...
Linus Torvalds [Thu, 11 Nov 2021 00:32:46 +0000 (16:32 -0800)]
Merge tag 'nfs-for-5.16-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Features:
- NFSv4.1 can always retrieve and cache the ACCESS mode on OPEN
- Optimisations for READDIR and the 'ls -l' style workload
- Further replacements of dprintk() with tracepoints and other
tracing improvements
- Ensure we re-probe NFSv4 server capabilities when the user does a
"mount -o remount"
Bugfixes:
- Fix an Oops in pnfs_mark_request_commit()
- Fix up deadlocks in the commit code
- Fix regressions in NFSv2/v3 attribute revalidation due to the
change_attr_type optimisations
- Fix some dentry verifier races
- Fix some missing dentry verifier settings
- Fix a performance regression in nfs_set_open_stateid_locked()
- SUNRPC was sending multiple SYN calls when re-establishing a TCP
connection.
- Fix multiple NFSv4 issues due to missing sanity checking of server
return values
- Fix a potential Oops when FREE_STATEID races with an unmount
Cleanups:
- Clean up the labelled NFS code
- Remove unused header <linux/pnfs_osd_xdr.h>"
* tag 'nfs-for-5.16-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (84 commits)
NFSv4: Sanity check the parameters in nfs41_update_target_slotid()
NFS: Remove the nfs4_label argument from decode_getattr_*() functions
NFS: Remove the nfs4_label argument from nfs_setsecurity
NFS: Remove the nfs4_label argument from nfs_fhget()
NFS: Remove the nfs4_label argument from nfs_add_or_obtain()
NFS: Remove the nfs4_label argument from nfs_instantiate()
NFS: Remove the nfs4_label from the nfs_setattrres
NFS: Remove the nfs4_label from the nfs4_getattr_res
NFS: Remove the f_label from the nfs4_opendata and nfs_openres
NFS: Remove the nfs4_label from the nfs4_lookupp_res struct
NFS: Remove the label from the nfs4_lookup_res struct
NFS: Remove the nfs4_label from the nfs4_link_res struct
NFS: Remove the nfs4_label from the nfs4_create_res struct
NFS: Remove the nfs4_label from the nfs_entry struct
NFS: Create a new nfs_alloc_fattr_with_label() function
NFS: Always initialise fattr->label in nfs_fattr_alloc()
NFSv4.2: alloc_file_pseudo() takes an open flag, not an f_mode
NFS: Don't allocate nfs_fattr on the stack in __nfs42_ssc_open()
NFSv4: Remove unnecessary 'minor version' check
NFSv4: Fix potential Oops in decode_op_map()
...
Linus Torvalds [Thu, 11 Nov 2021 00:15:54 +0000 (16:15 -0800)]
Merge branch 'exit-cleanups-for-v5.16' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull exit cleanups from Eric Biederman:
"While looking at some issues related to the exit path in the kernel I
found several instances where the code is not using the existing
abstractions properly.
This set of changes introduces force_fatal_sig a way of sending a
signal and not allowing it to be caught, and corrects the misuse of
the existing abstractions that I found.
A lot of the misuse of the existing abstractions are silly things such
as doing something after calling a no return function, rolling BUG by
hand, doing more work than necessary to terminate a kernel thread, or
calling do_exit(SIGKILL) instead of calling force_sig(SIGKILL).
In the review a deficiency in force_fatal_sig and force_sig_seccomp
where ptrace or sigaction could prevent the delivery of the signal was
found. I have added a change that adds SA_IMMUTABLE to change that
makes it impossible to interrupt the delivery of those signals, and
allows backporting to fix force_sig_seccomp
And Arnd found an issue where a function passed to kthread_run had the
wrong prototype, and after my cleanup was failing to build."
* 'exit-cleanups-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (23 commits)
soc: ti: fix wkup_m3_rproc_boot_thread return type
signal: Add SA_IMMUTABLE to ensure forced siganls do not get changed
signal: Replace force_sigsegv(SIGSEGV) with force_fatal_sig(SIGSEGV)
exit/r8188eu: Replace the macro thread_exit with a simple return 0
exit/rtl8712: Replace the macro thread_exit with a simple return 0
exit/rtl8723bs: Replace the macro thread_exit with a simple return 0
signal/x86: In emulate_vsyscall force a signal instead of calling do_exit
signal/sparc32: In setup_rt_frame and setup_fram use force_fatal_sig
signal/sparc32: Exit with a fatal signal when try_to_clear_window_buffer fails
exit/syscall_user_dispatch: Send ordinary signals on failure
signal: Implement force_fatal_sig
exit/kthread: Have kernel threads return instead of calling do_exit
signal/s390: Use force_sigsegv in default_trap_handler
signal/vm86_32: Properly send SIGSEGV when the vm86 state cannot be saved.
signal/vm86_32: Replace open coded BUG_ON with an actual BUG_ON
signal/sparc: In setup_tsb_params convert open coded BUG into BUG
signal/powerpc: On swapcontext failure force SIGSEGV
signal/sh: Use force_sig(SIGKILL) instead of do_group_exit(SIGKILL)
signal/mips: Update (_save|_restore)_fp_context to fail with -EFAULT
signal/sparc32: Remove unreachable do_exit in do_sparc_fault
...
Dave Airlie [Thu, 11 Nov 2021 00:14:44 +0000 (10:14 +1000)]
Merge tag 'amd-drm-fixes-5.16-2021-11-10' of https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-fixes-5.16-2021-11-10:
amdgpu:
- Don't allow partial copy from user for DC debugfs
- SRIOV fixes
- GFX9 CSB pin count fix
- Various IP version check fixes
- DP 2.0 fixes
- Limit DCN1 MPO fix to DCN1
amdkfd:
- SVM fixes
- Reset fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211110222536.7527-1-alexander.deucher@amd.com
Linus Torvalds [Thu, 11 Nov 2021 00:10:47 +0000 (16:10 -0800)]
Merge tag 'kernel.sys.v5.16' of git://git./linux/kernel/git/brauner/linux
Pull prctl updates from Christian Brauner:
"This contains the missing prctl uapi pieces for PR_SCHED_CORE.
In order to activate core scheduling the caller is expected to specify
the scope of the new core scheduling domain.
For example, passing 2 in the 4th argument of
prctl(PR_SCHED_CORE, PR_SCHED_CORE_CREATE, <pid>, 2, 0);
would indicate that the new core scheduling domain encompasses all
tasks in the process group of <pid>. Specifying 0 would only create a
core scheduling domain for the thread identified by <pid> and 2 would
encompass the whole thread-group of <pid>.
Note, the values 0, 1, and 2 correspond to PIDTYPE_PID, PIDTYPE_TGID,
and PIDTYPE_PGID. A first version tried to expose those values
directly to which I objected because:
- PIDTYPE_* is an enum that is kernel internal which we should not
expose to userspace directly.
- PIDTYPE_* indicates what a given struct pid is used for it doesn't
express a scope.
But what the 4th argument of PR_SCHED_CORE prctl() expresses is the
scope of the operation, i.e. the scope of the core scheduling domain
at creation time. So Eugene's patch now simply introduces three new
defines PR_SCHED_CORE_SCOPE_THREAD, PR_SCHED_CORE_SCOPE_THREAD_GROUP,
and PR_SCHED_CORE_SCOPE_PROCESS_GROUP. They simply express what
happens.
This has been on the mailing list for quite a while with all relevant
scheduler folks Cced. I announced multiple times that I'd pick this up
if I don't see or her anyone else doing it. None of this touches
proper scheduler code but only concerns uapi so I think this is fine.
With core scheduling being quite common now for vm managers (e.g.
moving individual vcpu threads into their own core scheduling domain)
and container managers (e.g. moving the init process into its own core
scheduling domain and letting all created children inherit it) having
to rely on raw numbers passed as the 4th argument in prctl() is a bit
annoying and everyone is starting to come up with their own defines"
* tag 'kernel.sys.v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
uapi/linux/prctl: provide macro definitions for the PR_SCHED_CORE type argument
Linus Torvalds [Thu, 11 Nov 2021 00:02:08 +0000 (16:02 -0800)]
Merge tag 'pidfd.v5.16' of git://git./linux/kernel/git/brauner/linux
Pull pidfd updates from Christian Brauner:
"Various places in the kernel have picked up pidfds.
The two most recent additions have probably been the ability to use
pidfds in bpf maps and the usage of pidfds in mm-based syscalls such
as process_mrelease() and process_madvise().
The same pattern to turn a pidfd into a struct task exists in two
places. One of those places used PIDTYPE_TGID while the other one used
PIDTYPE_PID even though it is clearly documented in all pidfd-helpers
that pidfds __currently__ only refer to thread-group leaders (subject
to change in the future if need be).
This isn't a bug per se but has the potential to be one if we allow
pidfds to refer to individual threads. If that happens we want to
audit all codepaths that make use of them to ensure they can deal with
pidfds refering to individual threads.
This adds a simple helper to turn a pidfd into a struct task making it
easy to grep for such places. Plus, it gets rid of code-duplication"
* tag 'pidfd.v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
mm: use pidfd_get_task()
pid: add pidfd_get_task() helper
Dave Airlie [Wed, 10 Nov 2021 22:14:02 +0000 (08:14 +1000)]
Merge tag 'drm-misc-next-fixes-2021-11-10' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
Removed the TTM Huge Page functionnality to address a crash, a timeout
fix for udl, CONFIG_FB dependency improvements, a fix for a circular
locking depency in imx, a NULL pointer dereference fix for virtio, and a
naming collision fix for drm/locking.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211110082114.vfpkpnecwdfg27lk@gilmour
Kai Vehmanen [Wed, 10 Nov 2021 21:03:07 +0000 (23:03 +0200)]
ALSA: hda: fix general protection fault in azx_runtime_idle
Fix a corner case between PCI device driver remove callback and
runtime PM idle callback.
Following sequence of events can happen:
- at azx_create, context is allocated with devm_kzalloc() and
stored as pci_set_drvdata()
- user-space requests to unbind audio driver
- dd.c:__device_release_driver() calls PCI remove
- pci-driver.c:pci_device_remove() calls the audio
driver azx_remove() callback and this is completed
- pci-driver.c:pm_runtime_put_sync() leads to a call
to rpm_idle() which again calls azx_runtime_idle()
- the azx context object, as returned by dev_get_drvdata(),
is no longer valid
-> access fault in azx_runtime_idle when executing
struct snd_card *card = dev_get_drvdata(dev);
chip = card->private_data;
if (chip->disabled || hda->init_failed)
This was discovered by i915_module_load test with 5.15.0 based
linux-next tree.
Example log caught by i915_module_load test with linux-next
https://intel-gfx-ci.01.org/tree/linux-next/
<4> [264.038232] general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b73f0: 0000 [#1] PREEMPT SMP NOPTI
<4> [264.038248] CPU: 0 PID: 5374 Comm: i915_module_loa Not tainted
5.15.0-next-20211109-gc8109c2ba35e-next-
20211109 #1
[...]
<4> [264.038267] RIP: 0010:azx_runtime_idle+0x12/0x60 [snd_hda_intel]
[...]
<4> [264.038355] Call Trace:
<4> [264.038359] <TASK>
<4> [264.038362] __rpm_callback+0x3d/0x110
<4> [264.038371] rpm_idle+0x27f/0x380
<4> [264.038376] __pm_runtime_idle+0x3b/0x100
<4> [264.038382] pci_device_remove+0x6d/0xa0
<4> [264.038388] device_release_driver_internal+0xef/0x1e0
<4> [264.038395] unbind_store+0xeb/0x120
<4> [264.038400] kernfs_fop_write_iter+0x11a/0x1c0
Fix the issue by setting drvdata to NULL at end of azx_remove().
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211110210307.1172004-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Wed, 10 Nov 2021 20:07:22 +0000 (12:07 -0800)]
Merge tag 'thermal-5.16-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"These fix two issues in the thermal core and one in the int340x
thermal driver.
Specifics:
- Replace pr_warn() with pr_warn_once() in user_space_bind() to
reduce kernel log noise (Rafael Wysocki).
- Extend the RFIM mailbox interface in the int340x thermal driver to
return 64 bit values to allow all values returned by the hardware
to be handled correctly (Srinivas Pandruvada).
- Fix possible NULL pointer dereferences in the of_thermal_ family of
functions (Subbaraman Narayanamurthy)"
* tag 'thermal-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: Replace pr_warn() with pr_warn_once() in user_space_bind()
thermal: Fix NULL pointer dereferences in of_thermal_ functions
thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses
Linus Torvalds [Wed, 10 Nov 2021 19:59:55 +0000 (11:59 -0800)]
Merge tag 'pm-5.16-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These fix three intel_pstate driver regressions, fix locking in the
core code suspending and resuming devices during system PM
transitions, fix the handling of cpuidle drivers based on runtime PM
during system-wide suspend, fix two issues in the operating
performance points (OPP) framework and resource-managed helpers to it.
Specifics:
- Fix two intel_pstate driver regressions related to the HWP
interrupt handling added recently (Srinivas Pandruvada).
- Fix intel_pstate driver regression introduced during the 5.11 cycle
and causing HWP desired performance to be mishandled in some cases
when switching driver modes and during system suspend and shutdown
(Rafael Wysocki).
- Fix system-wide device suspend and resume locking to avoid
deadlocks when device objects are deleted during a system-wide PM
transition (Rafael Wysocki).
- Modify system-wide suspend of devices to prevent cpuidle drivers
based on runtime PM from misbehaving during the "no IRQ" phase of
it (Ulf Hansson).
- Fix return value of _opp_add_static_v2() helper (YueHaibing).
- Fix required-opp handle count (Pavankumar Kondeti).
- Add resource managed OPP helpers, update dev_pm_opp_attach_genpd(),
update their devfreq users, and make minor DT binding change
(Dmitry Osipenko)"
* tag 'pm-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: sleep: Avoid calling put_device() under dpm_list_mtx
cpufreq: intel_pstate: Clear HWP Status during HWP Interrupt enable
cpufreq: intel_pstate: Fix unchecked MSR 0x773 access
cpufreq: intel_pstate: Clear HWP desired on suspend/shutdown and offline
PM: sleep: Fix runtime PM based cpuidle support
dt-bindings: opp: Allow multi-worded OPP entry name
opp: Fix return in _opp_add_static_v2()
PM / devfreq: tegra30: Check whether clk_round_rate() returns zero rate
PM / devfreq: tegra30: Use resource-managed helpers
PM / devfreq: Add devm_devfreq_add_governor()
opp: Add more resource-managed variants of dev_pm_opp_of_add_table()
opp: Change type of dev_pm_opp_attach_genpd(names) argument
opp: Fix required-opps phandle array count check
Linus Torvalds [Wed, 10 Nov 2021 19:52:40 +0000 (11:52 -0800)]
Merge tag 'acpi-5.16-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add support for a new ACPI device configuration object called
_DSC, fix some issues including one recent regression, add two new
items to quirk lists and clean up assorted pieces of code.
Specifics:
- Add support for new ACPI device configuration object called _DSC
("Deepest State for Configuration") to allow certain devices to be
probed without changing their power states, document it and make
two drivers use it (Sakari Ailus, Rajmohan Mani).
- Fix device wakeup power reference counting broken recently by
mistake (Rafael Wysocki).
- Drop unused symbol and macros depending on it from acgcc.h (Rafael
Wysocki).
- Add HP ZHAN 66 Pro to the "no EC wakeup" quirk list (Binbin Zhou).
- Add Xiaomi Mi Pad 2 to the backlight quirk list and drop an unused
piece of data from all of the list entries (Hans de Goede).
- Fix register read accesses handling in the Intel PMIC operation
region driver (Hans de Goede).
- Clean up static variables initialization in the EC driver
(wangzhitong)"
* tag 'acpi-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Documentation: ACPI: Fix non-D0 probe _DSC object example
ACPI: Drop ACPI_USE_BUILTIN_STDARG ifdef from acgcc.h
ACPI: PM: Fix device wakeup power reference counting error
ACPI: video: use platform backlight driver on Xiaomi Mi Pad 2
ACPI: video: Drop dmi_system_id.ident settings from video_detect_dmi_table[]
ACPI: PMIC: Fix intel_pmic_regs_handler() read accesses
ACPI: EC: Remove initialization of static variables to false
ACPI: EC: Use ec_no_wakeup on HP ZHAN 66 Pro
at24: Support probing while in non-zero ACPI D state
media: i2c: imx319: Support device probe in non-zero ACPI D state
ACPI: Add a convenience function to tell a device is in D0 state
Documentation: ACPI: Document _DSC object usage for enum power state
i2c: Allow an ACPI driver to manage the device's power state during probe
ACPI: scan: Obtain device's desired enumeration power state
Linus Torvalds [Wed, 10 Nov 2021 19:47:55 +0000 (11:47 -0800)]
Merge tag 'dmaengine-5.16-rc1' of git://git./linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"A bunch of driver updates, no new driver or controller support this
time though:
- Another pile of idxd updates
- pm routines cleanup for at_xdmac driver
- Correct handling of callback_result for few drivers
- zynqmp_dma driver updates and descriptor management refinement
- Hardware handshaking support for dw-axi-dmac
- Support for remotely powered controllers in Qcom bam dma
- tegra driver updates"
* tag 'dmaengine-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (69 commits)
dmaengine: ti: k3-udma: Set r/tchan or rflow to NULL if request fail
dmaengine: ti: k3-udma: Set bchan to NULL if a channel request fail
dmaengine: stm32-dma: avoid 64-bit division in stm32_dma_get_max_width
dmaengine: fsl-edma: support edma memcpy
dmaengine: idxd: fix resource leak on dmaengine driver disable
dmaengine: idxd: cleanup completion record allocation
dmaengine: zynqmp_dma: Correctly handle descriptor callbacks
dmaengine: xilinx_dma: Correctly handle cyclic descriptor callbacks
dmaengine: altera-msgdma: Correctly handle descriptor callbacks
dmaengine: at_xdmac: fix compilation warning
dmaengine: dw-axi-dmac: Simplify assignment in dma_chan_pause()
dmaengine: qcom: bam_dma: Add "powered remotely" mode
dt-bindings: dmaengine: bam_dma: Add "powered remotely" mode
dmaengine: sa11x0: Mark PM functions as __maybe_unused
dmaengine: switch from 'pci_' to 'dma_' API
dmaengine: ioat: switch from 'pci_' to 'dma_' API
dmaengine: hsu: switch from 'pci_' to 'dma_' API
dmaengine: hisi_dma: switch from 'pci_' to 'dma_' API
dmaengine: dw: switch from 'pci_' to 'dma_' API
dmaengine: dw-edma-pcie: switch from 'pci_' to 'dma_' API
...
Takashi Iwai [Wed, 10 Nov 2021 19:46:33 +0000 (20:46 +0100)]
ALSA: hda: Free card instance properly at probe errors
The recent change in hda-intel driver to allow repeated probes
surfaced a problem that has been hidden until; the probe process in
the work calls azx_free() at the error path, and this skips the card
free process that eventually releases codec instances. As a result,
we get a kernel WARNING like:
snd_hda_intel 0000:00:1f.3: Cannot probe codecs, giving up
------------[ cut here ]------------
WARNING: CPU: 14 PID: 186 at sound/hda/hdac_bus.c:73
....
For fixing this, we need to call snd_card_free() instead of
azx_free(). Additionally, the device drvdata has to be cleared, as
the driver binding itself is still active. Then the PM and other
driver callbacks will ignore the procedure.
Fixes:
c0f1886de7e1 ("ALSA: hda: intel: Allow repeatedly probing on codec configuration errors")
Reported-and-tested-by: Scott Branden <scott.branden@broadcom.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/063e2397-7edb-5f48-7b0d-618b938d9dd8@broadcom.com
Link: https://lore.kernel.org/r/20211110194633.19098-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Wed, 10 Nov 2021 19:36:43 +0000 (11:36 -0800)]
Merge tag 'tag-chrome-platform-for-v5.16' of git://git./linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros_ec_typec:
- Clean up use of cros_ec_check_features
cros_ec_*:
- Rename and move cros_ec_pd_command to cros_ec_command, and make
changes to cros_ec_typec and cros_ec_proto to use the new common
command, reducing duplication.
sensorhub:
- simplify getting .driver_data in cros_ec_sensors_core and
cros_ec_sensorhub
misc:
- Maintainership change. Enric Balletbo i Serra has moved on from
Collabora, so removing him from chrome/platform maintainers. Thanks
for all of your hard work maintaining this, Enric, and best of luck
to you in your new role!
- Add Prashant Malani as driver maintainer for cros_ec_typec.c and
cros_usbpd_notify. He was already principal contributor of these
drivers"
* tag 'tag-chrome-platform-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_proto: Use ec_command for check_features
platform/chrome: cros_ec_proto: Use EC struct for features
MAINTAINERS: Chrome: Drop Enric Balletbo i Serra
platform/chrome: cros_ec_typec: Use cros_ec_command()
platform/chrome: cros_ec_proto: Add version for ec_command
platform/chrome: cros_ec_proto: Make data pointers void
platform/chrome: cros_usbpd_notify: Move ec_command()
platform/chrome: cros_usbpd_notify: Rename cros_ec_pd_command()
platform/chrome: cros_ec: Fix spelling mistake "responsed" -> "response"
platform/chrome: cros_ec_sensorhub: simplify getting .driver_data
iio: common: cros_ec_sensors: simplify getting .driver_data
platform/chrome: cros-ec-typec: Cleanup use of check_features
platform/chrome: cros_ec_proto: Fix check_features ret val
MAINTAINERS: Add Prashant's maintainership of cros_ec drivers
Linus Torvalds [Wed, 10 Nov 2021 19:29:30 +0000 (11:29 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix double-evaluation of 'pte' macro argument when using 52-bit PAs
- Fix signedness of some MTE prctl PR_* constants
- Fix kmemleak memory usage by skipping early pgtable allocations
- Fix printing of CPU feature register strings
- Remove redundant -nostdlib linker flag for vDSO binaries
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: pgtable: make __pte_to_phys/__phys_to_pte_val inline functions
arm64: Track no early_pgtable_alloc() for kmemleak
arm64: mte: change PR_MTE_TCF_NONE back into an unsigned long
arm64: vdso: remove -nostdlib compiler flag
arm64: arm64_ftr_reg->name may not be a human-readable string
Linus Torvalds [Wed, 10 Nov 2021 19:25:37 +0000 (11:25 -0800)]
Merge tag 'arm-fixes-5.16' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is one set of fixes for the NXP/FSL DPAA2 drivers, addressing a
few minor issues. I received these just after sending out the last
v5.15 fixes, and nothing in here seemed urgent enough for a quick
follow-up"
* tag 'arm-fixes-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: fsl: dpaa2-console: free buffer before returning from dpaa2_console_read
soc: fsl: dpio: use the combined functions to protect critical zone
soc: fsl: dpio: replace smp_processor_id with raw_smp_processor_id
Linus Torvalds [Wed, 10 Nov 2021 19:22:03 +0000 (11:22 -0800)]
Merge tag 'asm-generic-5.16' of git://git./linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanup from Arnd Bergmann:
"This is a single cleanup from Peter Collingbourne, removing some dead
code"
* tag 'asm-generic-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: remove unused function syscall_set_arguments()
Linus Torvalds [Wed, 10 Nov 2021 19:14:21 +0000 (11:14 -0800)]
Merge tag 'for-linus-5.16b-rc1-tag' of git://git./linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- a series to speed up the boot of Xen PV guests
- some cleanups in Xen related code
- replacement of license texts with the appropriate SPDX headers and
fixing of wrong SPDX headers in Xen header files
- a small series making paravirtualized interrupt masking much simpler
and at the same time removing complaints of objtool
- a fix for Xen ballooning hogging workqueues for too long
- enablement of the Xen pciback driver for Arm
- some further small fixes/enhancements
* tag 'for-linus-5.16b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen/balloon: fix unused-variable warning
xen/balloon: rename alloc/free_xenballooned_pages
xen/balloon: add late_initcall_sync() for initial ballooning done
x86/xen: remove 32-bit awareness from startup_xen
xen: remove highmem remnants
xen: allow pv-only hypercalls only with CONFIG_XEN_PV
x86/xen: remove 32-bit pv leftovers
xen-pciback: allow compiling on other archs than x86
x86/xen: switch initial pvops IRQ functions to dummy ones
x86/xen: remove xen_have_vcpu_info_placement flag
x86/pvh: add prototype for xen_pvh_init()
xen: Fix implicit type conversion
xen: fix wrong SPDX headers of Xen related headers
xen/pvcalls-back: Remove redundant 'flush_workqueue()' calls
x86/xen: Remove redundant irq_enter/exit() invocations
xen-pciback: Fix return in pm_ctrl_init()
xen/x86: restrict PV Dom0 identity mapping
xen/x86: there's no highmem anymore in PV mode
xen/x86: adjust handling of the L3 user vsyscall special page table
xen/x86: adjust xen_set_fixmap()
...
Linus Torvalds [Wed, 10 Nov 2021 18:56:02 +0000 (10:56 -0800)]
Merge tag 'libnvdimm-for-5.16' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm update from Dan Williams:
"A single cleanup that precedes some deeper PMEM/DAX reworks that did
not settle in time for v5.16:
- Continue the cleanup of the dax api in preparation for a dax-device
block-device divorce"
* tag 'libnvdimm-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm/pmem: move dax_attribute_group from dax to pmem
Linus Torvalds [Wed, 10 Nov 2021 17:41:22 +0000 (09:41 -0800)]
Merge tag 'linux-watchdog-5.16-rc1' of git://linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- f71808e_wdt: convert to watchdog framework
- db8500_wdt: Rename driver (was ux500_wdt.c)
- sunxi: Add compatibles for R329 and D1
- mtk: add disable_wdt_extrst support
- several other small fixes and improvements
* tag 'linux-watchdog-5.16-rc1' of git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: db8500_wdt: Rename symbols
watchdog: db8500_wdt: Rename driver
watchdog: ux500_wdt: Drop platform data
watchdog: bcm63xx_wdt: fix fallthrough warning
watchdog: iTCO_wdt: No need to stop the timer in probe
watchdog: s3c2410: describe driver in KConfig
watchdog: sp5100_tco: Add support for get_timeleft
watchdog: mtk: add disable_wdt_extrst support
dt-bindings: watchdog: mtk-wdt: add disable_wdt_extrst support
watchdog: rza_wdt: Use semicolons instead of commas
watchdog: mlx-wdt: Use regmap_write_bits()
watchdog: rti-wdt: Make use of the helper function devm_platform_ioremap_resource()
watchdog: iTCO_wdt: Make use of the helper function devm_platform_ioremap_resource()
watchdog: ar7_wdt: Make use of the helper function devm_platform_ioremap_resource_byname()
watchdog: sunxi_wdt: Add support for D1
dt-bindings: watchdog: sunxi: Add compatibles for D1
ar7: fix kernel builds for compiler test
dt-bindings: watchdog: sunxi: Add compatibles for R329
watchdog: meson_gxbb_wdt: add timeout parameter
watchdog: meson_gxbb_wdt: add nowayout parameter
...
Linus Torvalds [Wed, 10 Nov 2021 17:07:26 +0000 (09:07 -0800)]
Merge tag 'rproc-v5.16' of git://git./linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
"The remoteproc repo is moved to a new path on git.kernel.org, to allow
Mathieu push access to the branches.
Support for the Mediatek MT8195 SCP was added, the related DeviceTree
binding was converted to YAML and MT8192 SCP was documented as well.
Amlogic Meson6, Meson8, Meson8b and Meson8m2 has an ARC core to aid in
resuming the system after suspend, a new remoteproc driver for booting
this core is introduced.
A new driver to support the DSP processor found on NXP i.MX8QM,
i.MX8QXP, i.MX8MP and i.MX8ULP is added.
The Qualcomm modem and TrustZone based remoteproc drivers gains
support for the modem in SC7280 and MSM8996 gains support for a
missing power-domain.
Throughout the Qualcomm drivers, the support for informing the
always-on power coprocessor about the state of each remoteproc is
reworked to avoid complications related to our use of genpd and the
system suspend state.
Lastly a number of small fixes are found throughout the drivers and
framework"
* tag 'rproc-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (39 commits)
remoteproc: Remove vdev_to_rvdev and vdev_to_rproc from remoteproc API
remoteproc: omap_remoteproc: simplify getting .driver_data
remoteproc: qcom_q6v5_mss: Use devm_platform_ioremap_resource_byname() to simplify code
remoteproc: Fix a memory leak in an error handling path in 'rproc_handle_vdev()'
remoteproc: Fix spelling mistake "atleast" -> "at least"
remoteproc: imx_dsp_rproc: mark PM functions as __maybe_unused
remoteproc: imx_dsp_rproc: Correct the comment style of copyright
dt-bindings: dsp: fsl: Update binding document for remote proc driver
remoteproc: imx_dsp_rproc: Add remoteproc driver for DSP on i.MX
remoteproc: imx_rproc: Add IMX_RPROC_SCU_API method
remoteproc: imx_rproc: Move common structure to header file
rpmsg: char: Remove useless include
remoteproc: meson-mx-ao-arc: fix a bit test
remoteproc: mss: q6v5-mss: Add modem support on SC7280
dt-bindings: remoteproc: qcom: Update Q6V5 Modem PIL binding
remoteproc: qcom: pas: Add SC7280 Modem support
dt-bindings: remoteproc: qcom: pas: Add SC7280 MPSS support
remoteproc: qcom: pas: Use the same init resources for MSM8996 and MSM8998
MAINTAINERS: Update remoteproc repo url
dt-bindings: remoteproc: k3-dsp: Cleanup SoC compatible from DT example
...
Linus Torvalds [Wed, 10 Nov 2021 17:05:11 +0000 (09:05 -0800)]
Merge tag 'rpmsg-v5.16' of git://git./linux/kernel/git/remoteproc/linux
Pull rpmsg updates from Bjorn Andersson:
"For the GLINK implementation this adds support for splitting outgoing
messages that are too large to fit in the fifo, it introduces the use
of "read notifications", to avoid polling in the case where the
outgoing fifo is full and a few bugs are squashed.
The return value of rpmsg_create_ept() for when RPMSG is disabled is
corrected to return a valid error, the Mediatek rpmsg driver is
updated to match the DT binding and a couple of cleanups are done in
the virtio rpmsg driver"
* tag 'rpmsg-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
rpmsg: glink: Send READ_NOTIFY command in FIFO full case
rpmsg: glink: Remove channel decouple from rpdev release
rpmsg: glink: Remove the rpmsg dev in close_ack
rpmsg: glink: Add TX_DATA_CONT command while sending
rpmsg: virtio_rpmsg_bus: use dev_warn_ratelimited for msg with no recipient
rpmsg: virtio: Remove unused including <linux/of_device.h>
rpmsg: Change naming of mediatek rpmsg property
rpmsg: Fix rpmsg_create_ept return when RPMSG config is not defined
rpmsg: glink: Replace strncpy() with strscpy_pad()
Guchun Chen [Wed, 10 Nov 2021 05:13:55 +0000 (13:13 +0800)]
drm/amdgpu: add missed support for UVD IP_VERSION(3, 0, 64)
Fixes:
96b8dd4423e74d ("drm/amdgpu/amdgpu_vcn: convert to IP version checking")
Signed-off-by: Flora Cui <flora.cui@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Guchun Chen [Wed, 10 Nov 2021 02:07:41 +0000 (10:07 +0800)]
drm/amdgpu: drop jpeg IP initialization in SRIOV case
Fixes:
b05b9c591f9ed6 ("drm/amdgpu: clean up set IP function")
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Shirish S [Mon, 8 Nov 2021 07:38:26 +0000 (13:08 +0530)]
drm/amd/display: reject both non-zero src_x and src_y only for DCN1x
[Why]
Video plane gets rejected for non-zero src_y and src_x on DCN2.x.
[How]
Limit the rejection till DCN1.x and verified MPO, by dragging video
playback beyond display's left (0, 0) co-ordinates.
Fixes:
d89f6048bdcb ("drm/amd/display: Reject non-zero src_y and src_x for video planes")
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jiri Olsa [Tue, 9 Nov 2021 11:42:17 +0000 (12:42 +0100)]
ftrace/direct: Fix lockup in modify_ftrace_direct_multi
We can't call unregister_ftrace_function under ftrace_lock.
Link: https://lkml.kernel.org/r/20211109114217.1645296-1-jolsa@kernel.org
Fixes:
ed29271894aa ("ftrace/direct: Do not disable when switching direct callers")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Mon, 8 Nov 2021 15:58:10 +0000 (10:58 -0500)]
ring-buffer: Protect ring_buffer_reset() from reentrancy
The resetting of the entire ring buffer use to simply go through and reset
each individual CPU buffer that had its own protection and synchronization.
But this was very slow, due to performing a synchronization for each CPU.
The code was reshuffled to do one disabling of all CPU buffers, followed
by a single RCU synchronization, and then the resetting of each of the CPU
buffers. But unfortunately, the mutex that prevented multiple occurrences
of resetting the buffer was not moved to the upper function, and there is
nothing to protect from it.
Take the ring buffer mutex around the global reset.
Cc: stable@vger.kernel.org
Fixes:
b23d7a5f4a07a ("ring-buffer: speed up buffer resets by avoiding synchronize_rcu for each CPU")
Reported-by: "Tzvetomir Stoyanov (VMware)" <tz.stoyanov@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Kai-Heng Feng [Wed, 10 Nov 2021 14:40:32 +0000 (22:40 +0800)]
ALSA: hda/realtek: Add quirk for HP EliteBook 840 G7 mute LED
The mute and micmute LEDs don't work on HP EliteBook 840 G7. The same
quirk for other HP laptops can let LEDs work, so apply it.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211110144033.118451-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dust Li [Wed, 10 Nov 2021 07:02:34 +0000 (15:02 +0800)]
net/smc: fix sk_refcnt underflow on linkdown and fallback
We got the following WARNING when running ab/nginx
test with RDMA link flapping (up-down-up).
The reason is when smc_sock fallback and at linkdown
happens simultaneously, we may got the following situation:
__smc_lgr_terminate()
--> smc_conn_kill()
--> smc_close_active_abort()
smc_sock->sk_state = SMC_CLOSED
sock_put(smc_sock)
smc_sock was set to SMC_CLOSED and sock_put() been called
when terminate the link group. But later application call
close() on the socket, then we got:
__smc_release():
if (smc_sock->fallback)
smc_sock->sk_state = SMC_CLOSED
sock_put(smc_sock)
Again we set the smc_sock to CLOSED through it's already
in CLOSED state, and double put the refcnt, so the following
warning happens:
refcount_t: underflow; use-after-free.
WARNING: CPU: 5 PID: 860 at lib/refcount.c:28 refcount_warn_saturate+0x8d/0xf0
Modules linked in:
CPU: 5 PID: 860 Comm: nginx Not tainted 5.10.46+ #403
Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS
8c24b4c 04/01/2014
RIP: 0010:refcount_warn_saturate+0x8d/0xf0
Code: 05 5c 1e b5 01 01 e8 52 25 bc ff 0f 0b c3 80 3d 4f 1e b5 01 00 75 ad 48
RSP: 0018:
ffffc90000527e50 EFLAGS:
00010286
RAX:
0000000000000026 RBX:
ffff8881300df2c0 RCX:
0000000000000027
RDX:
0000000000000000 RSI:
ffff88813bd58040 RDI:
ffff88813bd58048
RBP:
0000000000000000 R08:
0000000000000003 R09:
0000000000000001
R10:
ffff8881300df2c0 R11:
ffffc90000527c78 R12:
ffff8881300df340
R13:
ffff8881300df930 R14:
ffff88810b3dad80 R15:
ffff8881300df4f8
FS:
00007f739de8fb80(0000) GS:
ffff88813bd40000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
000000000a01b008 CR3:
0000000111b64003 CR4:
00000000003706e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
smc_release+0x353/0x3f0
__sock_release+0x3d/0xb0
sock_close+0x11/0x20
__fput+0x93/0x230
task_work_run+0x65/0xa0
exit_to_user_mode_prepare+0xf9/0x100
syscall_exit_to_user_mode+0x27/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This patch adds check in __smc_release() to make
sure we won't do an extra sock_put() and set the
socket to CLOSED when its already in CLOSED state.
Fixes:
51f1de79ad8e (net/smc: replace sock_put worker by socket refcounting)
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 10 Nov 2021 08:07:06 +0000 (11:07 +0300)]
net/mlx5: Lag, fix a potential Oops with mlx5_lag_create_definer()
There is a minus character missing from ERR_PTR(ENOMEM) so if this
allocation fails it will lead to an Oops in the caller.
Fixes:
dc48516ec7d3 ("net/mlx5: Lag, add support to create definers for LAG")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 10 Nov 2021 08:11:09 +0000 (11:11 +0300)]
gve: fix unmatched u64_stats_update_end()
The u64_stats_update_end() call is supposed to be inside the curly
braces so it pairs with the u64_stats_update_begin().
Fixes:
37149e9374bf ("gve: Implement packet continuation for RX.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksander Jan Bajkowski [Tue, 9 Nov 2021 22:23:54 +0000 (23:23 +0100)]
net: ethernet: lantiq_etop: Fix compilation error
This fixes the error detected when compiling the driver.
Fixes:
14d4e308e0aa ("net: lantiq: configure the burst length in ethernet drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Tue, 9 Nov 2021 16:17:34 +0000 (17:17 +0100)]
selftests: forwarding: Fix packet matching in mirroring selftests
In commit
6de6e46d27ef ("cls_flower: Fix inability to match GRE/IPIP
packets"), cls_flower was fixed to match an outer packet of a tunneled
packet as would be expected, rather than dissecting to the inner packet and
matching on that.
This fix uncovered several issues in packet matching in mirroring
selftests:
- in mirror_gre_bridge_1d_vlan.sh and mirror_gre_vlan_bridge_1q.sh, the
vlan_ethtype match is copied around as "ip", even as some of the tests
are running over ip6gretap. This is fixed by using an "ipv6" for
vlan_ethtype in the ip6gretap tests.
- in mirror_gre_changes.sh, a filter to count GRE packets is set up to
match TTL of 50. This used to trigger in the offloaded datapath, where
the envelope TTL was matched, but not in the software datapath, which
considered TTL of the inner packet. Now that both match consistently, all
the packets were double-counted. This is fixed by marking the filter as
skip_hw, leaving only the SW datapath component active.
Fixes:
6de6e46d27ef ("cls_flower: Fix inability to match GRE/IPIP packets")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eiichi Tsukata [Tue, 9 Nov 2021 00:15:02 +0000 (00:15 +0000)]
vsock: prevent unnecessary refcnt inc for nonblocking connect
Currently vosck_connect() increments sock refcount for nonblocking
socket each time it's called, which can lead to memory leak if
it's called multiple times because connect timeout function decrements
sock refcount only once.
Fixes it by making vsock_connect() return -EALREADY immediately when
sock state is already SS_CONNECTING.
Fixes:
d021c344051a ("VSOCK: Introduce VM Sockets")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Mon, 8 Nov 2021 21:49:18 +0000 (22:49 +0100)]
net: marvell: mvpp2: Fix wrong SerDes reconfiguration order
Commit
bfe301ebbc94 ("net: mvpp2: convert to use
mac_prepare()/mac_finish()") introduced a bug wherein it leaves the MAC
RESET register asserted after mac_finish(), due to wrong order of
function calls.
Before it was:
.mac_config()
mvpp22_mode_reconfigure()
assert reset
mvpp2_xlg_config()
deassert reset
Now it is:
.mac_prepare()
.mac_config()
mvpp2_xlg_config()
deassert reset
.mac_finish()
mvpp2_xlg_config()
assert reset
Obviously this is wrong.
This bug is triggered when phylink tries to change the PHY interface
mode from a GMAC mode (sgmii, 1000base-x, 2500base-x) to XLG mode
(10gbase-r, xaui). The XLG mode does not work since reset is left
asserted. Only after
ifconfig down && ifconfig up
is called will the XLG mode work.
Move the call to mvpp22_mode_reconfigure() to .mac_prepare()
implementation. Since some of the subsequent functions need to know
whether the interface is being changed, we unfortunately also need to
pass around the new interface mode before setting port->phy_interface.
Fixes:
bfe301ebbc94 ("net: mvpp2: convert to use mac_prepare()/mac_finish()")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Mon, 8 Nov 2021 21:28:55 +0000 (22:28 +0100)]
net: ethernet: ti: cpsw_ale: Fix access to un-initialized memory
It is spurious to allocate a bitmap without initializing it.
So, better safe than sorry, initialize it to 0 at least to have some known
values.
While at it, switch to the devm_bitmap_ API which is less verbose.
Fixes:
4b41d3436796 ("net: ethernet: ti: cpsw: allow untagged traffic on host port")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 8 Nov 2021 20:28:54 +0000 (22:28 +0200)]
net: stmmac: allow a tc-taprio base-time of zero
Commit
fe28c53ed71d ("net: stmmac: fix taprio configuration when
base_time is in the past") allowed some base time values in the past,
but apparently not all, the base-time value of 0 (Jan 1st 1970) is still
explicitly denied by the driver.
Remove the bogus check.
Fixes:
b60189e0392f ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Righi [Fri, 5 Nov 2021 15:55:29 +0000 (16:55 +0100)]
selftests: net: test_vxlan_under_vrf: fix HV connectivity test
It looks like test_vxlan_under_vrf.sh is always failing to verify the
connectivity test during the ping between the two simulated VMs.
This is due to the fact that veth-hv in each VM should have a distinct
MAC address.
Fix by setting a unique MAC address on each simulated VM interface.
Without this fix:
$ sudo ./tools/testing/selftests/net/test_vxlan_under_vrf.sh
Checking HV connectivity [ OK ]
Check VM connectivity through VXLAN (underlay in the default VRF) [FAIL]
With this fix applied:
$ sudo ./tools/testing/selftests/net/test_vxlan_under_vrf.sh
Checking HV connectivity [ OK ]
Check VM connectivity through VXLAN (underlay in the default VRF) [ OK ]
Check VM connectivity through VXLAN (underlay in a VRF) [FAIL]
NOTE: the connectivity test with the underlay VRF is still failing; it
seems that ARP requests are blocked at the simulated hypervisor level,
probably due to some missing ARP forwarding rules. This requires more
investigation (in the meantime we may consider to set that test as
expected failure - XFAIL).
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 10 Nov 2021 14:20:43 +0000 (14:20 +0000)]
Merge branch 'hns3-fixes'
Guangbin Huang says:
====================
net: hns3: add some fixes for -net
This series adds some fixes for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangbin Huang [Wed, 10 Nov 2021 13:42:56 +0000 (21:42 +0800)]
net: hns3: allow configure ETS bandwidth of all TCs
Currently, driver only allow configuring ETS bandwidth of TCs according
to the max TC number queried from firmware. However, the hardware actually
supports 8 TCs and users may need to configure ETS bandwidth of all TCs,
so remove the restriction.
Fixes:
330baff5423b ("net: hns3: add ETS TC weight setting in SSU module")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangbin Huang [Wed, 10 Nov 2021 13:42:55 +0000 (21:42 +0800)]
net: hns3: remove check VF uc mac exist when set by PF
If users set unicast mac address for VFs by PF, they need to guarantee all
VFs' address is different. This patch removes the check mac address exist
of VFs, for usrs can refresh mac addresses of all VFs directly without
need to modify the exist mac address to other value firstly.
Fixes:
8e6de441b8e6 ("net: hns3: add support for configuring VF MAC from the host")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangbin Huang [Wed, 10 Nov 2021 13:42:54 +0000 (21:42 +0800)]
net: hns3: fix some mac statistics is always 0 in device version V2
When driver queries the register number of mac statistics from firmware,
the old firmware runs in device version V2 only returns number of valid
registers, not include number of three reserved registers among of them.
It cause driver doesn't record the last three data when query mac
statistics.
To fix this problem, driver never query register number in device version
V2 and set it to a fixed value which include three reserved registers.
Fixes:
c8af2887c941 ("net: hns3: add support pause/pfc durations for mac statistics")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>