scsi: hpsa: Do not set COMMAND_COMPLETE

COMMAND_COMPLETE is defined as '0', and it is a SCSI parallel message to
boot. Drop the call to set_msg_byte().

Link: https://lore.kernel.org/r/20210113090500.129644-17-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Avoid setting message byte on completion

The aacraid controller is a RAID controller and the driver will never see
any SCSI messages. Plus it's quite pointless to set the message byte if the
host byte is already set, as the latter takes precedence during error
recovery.  Drop the message byte values for the final result.

Link: https://lore.kernel.org/r/20210113090500.129644-16-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: zfcp: Do not set COMMAND_COMPLETE

COMMAND_COMPLETE is defined as '0', and it is a SCSI parallel message to
boot. So drop the call to set_msg_byte().

Link: https://lore.kernel.org/r/20210113090500.129644-15-hare@suse.de
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Use standard SAM status definitions

Use standard SAM status definitions and drop the driver-defined ones.

Link: https://lore.kernel.org/r/20210113090500.129644-14-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: dc395: Drop private SAM status code definitions

We don't need to duplicate definitions from the common include files.

Link: https://lore.kernel.org/r/20210113090500.129644-13-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: nsp32: Fixup status handling

SCp.status is always the SAM-defined status value, not the Linux
ones. Fixup the one wrong definition.

Link: https://lore.kernel.org/r/20210113090500.129644-12-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: acornscsi: Use standard defines

Use midlayer-defined values and drop the non-existing QUEUE_FULL case; we
are checking the SCSI messages in the switch statement, and QUEUE_FULL is a
SCSI status hence it can never occur here.

Link: https://lore.kernel.org/r/20210113090500.129644-11-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Drop driver-defined SCSI status codes

Drop the driver-defined SCSI status codes and use the generic ones instead.

Link: https://lore.kernel.org/r/20210113090500.129644-10-hare@suse.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aic7xxx: aic79xx: Remove driver-defined SAM status definitions

Replace the driver-defined SAM status definitions with the standard
mid-layer defined ones.

Link: https://lore.kernel.org/r/20210113090500.129644-9-hare@suse.de
Reviewed-by: Bart van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aic7xxx: aic79xx: Kill pointless forward declarations

Link: https://lore.kernel.org/r/20210113090500.129644-8-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aic7xxx: aic79xx: Whitespace cleanup

Link: https://lore.kernel.org/r/20210113090500.129644-7-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: atp870u: Whitespace cleanup

Link: https://lore.kernel.org/r/20210113090500.129644-6-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: 3w-sas: Whitespace cleanup

Link: https://lore.kernel.org/r/20210113090500.129644-5-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: 3w-9xxx: Whitespace cleanup

Link: https://lore.kernel.org/r/20210113090500.129644-4-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: 3w-xxxx: Whitespace cleanup

Link: https://lore.kernel.org/r/20210113090500.129644-3-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: Drop gdth driver

The gdth driver refers to a SCSI parallel, PCI-only HBA RAID adapter which
was manufactured by the now-defunct ICP Vortex company, later acquired by
Adaptec and superseded by the aacraid series of controllers.  The driver
itself would require a major overhaul before any modifications can be
attempted, but seeing that it's unlikely to have any users left it should
rather be removed completely.

Link: https://lore.kernel.org/r/20210113090500.129644-2-hare@suse.de
Cautiously-Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: core: Remove in_interrupt() check in transport_handle_cdb_direct()

transport_handle_cdb_direct() uses in_interrupt() to detect if it is safe
to sleep. It produces a stack trace and returns with an error which is
clearly for debugging.

The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

transport_handle_cdb_direct() has a comment saying that it may only be
invoked from process context. It invokes transport_generic_new_cmd() which
performs GFP_KERNEL memory allocations. in_interrupt() does not detect all
the contexts where it is invalid to sleep (for the blocking GFP_KERNEL
allocation) as it fails to detect sections with disabled preemption.

Replace the in_interrupt() based check with a might_sleep() annotation.

Link: https://lore.kernel.org/r/20201220203638.43615-7-bigeasy@linutronix.de
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: core: Replace in_interrupt() usage in target_submit_cmd_map_sgls()

target_submit_cmd_map_sgls() uses in_interrupt() to crash if it returns
true.

The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

The usage of in_interrupt() is clearly for debugging. might_sleep() is
better at this because it also detects other contexts in which it is not
allowed to sleep, like preempt-disabled section.

Replace BUG_ON(in_interrupt) with might_sleep().

Link: https://lore.kernel.org/r/20201220203638.43615-6-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: alua: Remove in_interrupt() usage in core_alua_check_nonop_delay()

core_alua_check_nonop_delay() uses in_interrupt() to decide if it is safe
to sleep.

The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

core_alua_check_nonop_delay() has two callers:

 - target_submit_cmd_map_sgls()
   Kernel doc says it that it must be called from process context. Also has
   a BUG_ON(in_interrupt()).

 - iscsit_setup_scsi_cmd()
   Invokes iscsit_add_reject_cmd() which does GFP_KERNEL allocation and
   target_cmd_init_cdb() which may do GFP_KERNEL allocations.

Remove the in_interrupt() check because all callers are from preemptible
context.

Link: https://lore.kernel.org/r/20201220203638.43615-5-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: iscsi: Redo iscsit_check_session_usage_count() return code

The return value of iscsit_check_session_usage_count() is only checked if
it was not allowed to sleep. If it returns `2' then a timer is prepared. If
it returns something else or if it was allowed to sleep then it is ignored.

Let iscsit_check_session_usage_count() return true if it needs to arm the
timer - otherwise false. This simplifies the code flow of the only caller.

Link: https://lore.kernel.org/r/20201220203638.43615-4-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: iscsi: Avoid in_interrupt() usage in iscsit_check_session_usage_count()

iscsit_check_session_usage_count() uses in_interrupt() to find out if it is
safe to invoke wait_for_completion().

The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

There is only one caller of iscsit_check_session_usage_count() which
already has an argument indicating if it is safe to sleep.

Extend iscsit_check_session_usage_count() by an argument indicating if it
may sleep.

Link: https://lore.kernel.org/r/20201220203638.43615-3-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: iscsi: Avoid in_interrupt() usage in iscsit_close_session()

iscsit_close_session() uses in_interrupt() to decide if it needs to check
the return value of iscsit_check_session_usage_count() if it was not able
to sleep.

The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.

iscsit_close_session() has two callers:

 - iscsit_handle_time2retain_timeout()
   A timer_list callback.

 - iscsit_close_connection()
   Runs in preemptible context, acquires a mutex.

Add an argument to iscsit_close_session() indicating if sleeping is
possible.

Link: https://lore.kernel.org/r/20201220203638.43615-2-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Clean up and refactor clk-scaling feature

Manipulate clock scaling related stuff only if the host capability supports
clock scaling feature to avoid redundant code execution.

Link: https://lore.kernel.org/r/20210120150142.5049-4-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Remove redundant null checking of devfreq instance

hba->devfreq is zero-initialized thus it is not required to check its
existence in ufshcd_add_lus() function which is invoked during
initialization only.

Link: https://lore.kernel.org/r/20210120150142.5049-3-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Refactor cancelling clkscaling works

Cancelling suspend_work and resume_work is only required while suspending
clk-scaling. Move these two invocations into ufshcd_suspend_clkscaling()
function.

Link: https://lore.kernel.org/r/20210120150142.5049-2-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Revert "Make sure clk scaling happens only when HBA is runtime ACTIVE"

Commit 73cc291c2702 ("scsi: ufs: Make sure clk scaling happens only
when HBA is runtime ACTIVE") is no longer needed since commit
0e9d4ca43ba8 ("scsi: ufs: Protect some contexts from unexpected clock
scaling") is a more mature fix to protect UFS LLD stability from clock
scaling invoked through sysfs nodes by users.

Link: https://lore.kernel.org/r/1611137065-14266-4-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Refactor ufshcd_init/exit_clk_scaling/gating()

ufshcd_hba_exit() is always called after ufshcd_exit_clk_scaling() and
ufshcd_exit_clk_gating(). Move ufshcd_exit_clk_scaling/gating() to
ufshcd_hba_exit(). Meanwhile, add dedicated functions to initialize
and remove sysfs nodes of clock scaling/gating to make the code more
readable. Overall functionality remains same.

Link: https://lore.kernel.org/r/1611137065-14266-3-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Protect some contexts from unexpected clock scaling

In contexts like suspend, shutdown, and error handling we need to
suspend devfreq to make sure these contexts won't be disturbed by
clock scaling.  However, suspending devfreq is not enough since users
can still trigger a clock scaling by manipulating the devfreq sysfs
nodes like min/max_freq and governor even after devfreq is
suspended. Moreover, mere suspending devfreq cannot synchroinze a
clock scaling which has already been invoked through these sysfs
nodes. Add one more flag in struct clk_scaling and wrap the entire
func ufshcd_devfreq_scale() with the clk_scaling_lock, so that we can
use this flag and clk_scaling_lock to control and synchronize clock
scaling invoked through devfreq sysfs nodes.

Link: https://lore.kernel.org/r/1611137065-14266-2-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Group UFS WB related flags in struct ufs_dev_info

UFS device-related flags should be grouped in ufs_dev_info. Move wb_enabled
and wb_buf_flush_enabled out from struct ufs_hba, group them in struct
ufs_dev_info, and align the names of the structure members vertically.

Link: https://lore.kernel.org/r/20210119163847.20165-6-huobean@gmail.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Remove two WB related fields from struct ufs_dev_info

d_wb_alloc_units and d_ext_ufs_feature_sup are only used during WB probe.
They are used to confirm the condition that "if bWriteBoosterBufferType
is set to 01h but dNumSharedWriteBoosterBufferAllocUnits is set to zero,
the WriteBooster feature is disabled", and if UFS device supports WB.

No need to keep them after probing is complete.

Link: https://lore.kernel.org/r/20210119163847.20165-5-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Update comment in the function ufshcd_wb_probe()

USFHCD supports both WriteBooster "LU dedicated buffer" mode and "shared
buffer" mode. Update the comment accordingly in the function
ufshcd_wb_probe().

Link: https://lore.kernel.org/r/20210119163847.20165-4-huobean@gmail.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: docs: ABI: Add wb_on documentation for new entry wb_on

Adds UFS sysfs documentation for new entry wb_on.

[mkp: fix doc formatting]

Link: https://lore.kernel.org/r/20210119163847.20165-3-huobean@gmail.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fix format

scsi: ufs: Add "wb_on" sysfs node to control WB on/off

Currently UFS WriteBooster driver uses clock scaling up/down to set WB
on/off. For the platforms which don't support UFSHCD_CAP_CLK_SCALING, WB
will be always on. Provide a sysfs attribute to enable/disable WB during
runtime. Write 1/0 to "wb_on" sysfs node to enable/disable UFS WB.

Link: https://lore.kernel.org/r/20210119163847.20165-2-huobean@gmail.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: ufs-exynos: Use UFSHCD_QUIRK_ALIGN_SG_WITH_PAGE_SIZE

Exynos needs scatterlist entries aligned to page size because it isn't
capable of transferring data contained in one DATA IN operation to seversal
areas in memory.

Link: https://lore.kernel.org/r/80d7e27d6ec537e650a6bd74897b6c60618efcdc.1611026909.git.kwmad.kim@samsung.com
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Introduce a quirk to allow only page-aligned sg entries

Some SoCs require a single scatterlist entry for smaller than page size,
i.e. 4KB. When dispatching commands with more than one scatterlist entry
under 4KB in size the following behavior is observed:

A command to read a block range is dispatched with two scatterlist entries
that are named AAA and BBB. After dispatching, the host builds two PRDT
entries and during transmission, device sends just one DATA IN because
device doesn't care about host DMA. The host then transfers the combined
amount of data from start address of the area named AAA. As a consequence,
the area that follows AAA in memory would be corrupted.

    |<------------->|
    +-------+------------         +-------+
    +  AAA  + (corrupted)   ...   +  BBB  +
    +-------+------------         +-------+

To avoid this we need to enforce page size alignment for sg entries.

Link: https://lore.kernel.org/r/56dddef94f60bd9466fd77e69f64bbbd657ed2a1.1611026909.git.kwmad.kim@samsung.com
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Delete redundant if statement in ufshcd_intr()

Once going into while-do loop, intr_status is already true, this
if-statement is redundant, remove it.

Link: https://lore.kernel.org/r/20210118201233.3043-1-huobean@gmail.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Fix spelling mistake "succeded" -> "succeeded"

There is a spelling mistake in a ibmvfc_dbg debug message. Fix it.

Link: https://lore.kernel.org/r/20210118111346.70798-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Switch from 'pci_' to 'dma_' API

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.  It has been compile
tested.

When memory is allocated in 'pm8001_init_ccb_tag()' GFP_KERNEL can be used
because this function already uses this flag a few lines above.

While at it, remove "pm80xx: " in a debug message. 'pm8001_dbg()' already
adds the driver name in the message.

@@
@@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@
@@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@
@@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@
@@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)

Link: https://lore.kernel.org/r/20210117132445.562552-1-christophe.jaillet@wanadoo.fr
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Clean up indentation of a code block

A block of code is indented one level too deeply, clean this up.

Link: https://lore.kernel.org/r/20210115095824.9170-1-colin.king@canonical.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Indentation does not match nesting level")

Merge branch '5.11/scsi-fixes' into 5.12/scsi-queue

Pull in the 5.11 SCSI fixes branch to provide an updated baseline for
megaraid and hisi_sas. Both drivers received core changes in
v5.11-rc3.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Add support for eh_should_retry_cmd()

Add support for eh_should_retry_cmd callback in lpfc_template.

Link: https://lore.kernel.org/r/1609969748-17684-6-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_transport_fc: Add store capability to rport port_state in sysfs

Add store capability to the rport port_state using sysfs under
fc_remote_ports/rport-*/port_state.

With this the user can move the port_state from Marginal->Online and
Online->Marginal.

 - Marginal: This interface will set SCMD_NORETRIES_ABORT bit in
   scmd->state for all the pending I/Os on the SCSI device associated with
   target port.

 - Online: This interface will clear SCMD_NORETRIES_ABORT bit in
   scmd->state for all the pending I/Os on the SCSI device associated with
   target port.

The following interface is provided to set the port state to Marginal and
Online respectively:

echo "Marginal" >> /sys/class/fc_remote_ports/rport-X\:Y-Z/port_state
echo "Online" >> /sys/class/fc_remote_ports/rport-X\:Y-Z/port_state

Link: https://lore.kernel.org/r/1609969748-17684-5-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_transport_fc: Add a new rport state FC_PORTSTATE_MARGINAL

Add a new interface, fc_eh_should_retry_cmd(), which checks if the cmd
should be retried or not by checking the rport state. If the rport state is
marginal it returns false to make sure there won't be any retries on the
cmd.

Make the fc_remote_port_delete(), fc_user_scan_tgt(), and
fc_timeout_deleted_rport() functions handle the new rport state.

Link: https://lore.kernel.org/r/1609969748-17684-4-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: core: No retries on abort success

Add a new optional routine, eh_should_retry_cmd(), in scsi_host_template
that allows the transport to decide if a cmd is retryable. Return true if
the transport is in a state the cmd should be retried on.

Update scmd_eh_abort_handler() and scsi_eh_flush_done_q() to both call
scsi_eh_should_retry_cmd() to check whether the command needs to be
retried.

The above changes were based on a patch by Mike Christie.

Link: https://lore.kernel.org/r/1609969748-17684-3-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: core: Add a new error code DID_TRANSPORT_MARGINAL in scsi.h

Add code in scsi_result_to_blk_status to translate a new error
DID_TRANSPORT_MARGINAL to the corresponding blk_status_t i.e
BLK_STS_TRANSPORT.

Add DID_TRANSPORT_MARGINAL case to scsi_decide_disposition().

Link: https://lore.kernel.org/r/1609969748-17684-2-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Provide modules parameters for MQ settings

Add the various module parameter toggles for adjusting the MQ
characteristics at boot/load time as well as a device attribute for
changing the client scsi channel request amount.

Link: https://lore.kernel.org/r/20210114203148.246656-22-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Enable MQ and set reasonable defaults

Turn on MQ by default and set sane values for the upper limit on hw queues
for the SCSI host, and number of hw SCSI channels to request from the
partner VIOS.

Link: https://lore.kernel.org/r/20210114203148.246656-21-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Purge SCSI channels after transport loss/reset

Grab the queue and list lock for each Sub-CRQ and add any uncompleted
events to the host purge list.

Link: https://lore.kernel.org/r/20210114203148.246656-20-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Send Cancel MAD down each hw SCSI channel

In general the client needs to send Cancel MADs and task management
commands down the same channel as the command(s) intended to cancel or
abort. The client assigns cancel keys per LUN and thus must send a Cancel
down each channel commands were submitted for that LUN. Further, the client
then must wait for those cancel completions prior to submitting a LUN RESET
or ABORT TASK SET.

Add a cancel rsp iu syncronization field to the ibmvfc_queue struct such
that the cancel routine can sync the cancel response to each queue that
requires a cancel command. Build a list of each cancel event sent and wait
for the completion of each submitted cancel.

Link: https://lore.kernel.org/r/20210114203148.246656-19-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Add cancel mad initialization helper

Add a helper routine for initializing a Cancel MAD. This will be useful for
a channelized client that needs to send Cancel commands down every channel
commands were sent for a particular LUN.

Link: https://lore.kernel.org/r/20210114203148.246656-18-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Register Sub-CRQ handles with VIOS during channel setup

If the ibmvfc client adapter requests channels it must submit a number of
Sub-CRQ handles matching the number of channels being requested. The VIOS
in its response will overwrite the actual number of channel resources
allocated which may be less than what was requested. The client then must
store the VIOS Sub-CRQ handle for each queue. This VIOS handle is needed as
a parameter with h_send_sub_crq().

Link: https://lore.kernel.org/r/20210114203148.246656-17-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Send commands down HW Sub-CRQ when channelized

When the client has negotiated the use of channels all vfcFrames are
required to go down a Sub-CRQ channel or it is a protocoal violation. If
the adapter state is channelized submit vfcFrames to the appropriate
Sub-CRQ via the h_send_sub_crq() helper.

Link: https://lore.kernel.org/r/20210114203148.246656-16-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Set and track hw queue in ibmvfc_event struct

Extract the hwq id from a SCSI command and store it in the ibmvfc_event
structure to identify which Sub-CRQ to send the command down when channels
are being utilized.

Link: https://lore.kernel.org/r/20210114203148.246656-15-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Advertise client support for using hardware channels

Previous patches have plumbed the necessary Sub-CRQ interface and channel
negotiation MADs to fully channelize via hardware backed queues.

Advertise client support via NPIV Login capability IBMVFC_CAN_USE_CHANNELS
when the client bits have MQ enabled via vhost->mq_enabled, or when
channels were already in use during a subsequent NPIV Login. The later is
required because channel support is only renegotiated after a CRQ pair is
broken. Simple NPIV Logout/Logins require the client to continue to
advertise the channel capability until the CRQ pair between the client is
broken.

Link: https://lore.kernel.org/r/20210114203148.246656-14-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Implement channel enquiry and setup commands

New NPIV_ENQUIRY_CHANNEL and NPIV_SETUP_CHANNEL management datagrams (MADs)
were defined in a previous patchset. If the client advertises a desire to
use channels and the partner VIOS is channel capable then the client must
proceed with channel enquiry to determine the maximum number of channels
the VIOS is capable of providing, and registering SubCRQs via channel setup
with the VIOS immediately following NPIV Login. This handshaking should not
be performed for subsequent NPIV Logins unless the CRQ connection has been
reset.

Implement these two new MADs and issue them following a successful NPIV
login where the VIOS has set the SUPPORT_CHANNELS capability bit in the
NPIV Login response.

Link: https://lore.kernel.org/r/20210114203148.246656-13-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Map/request irq and register Sub-CRQ interrupt handler

Create an irq mapping for the hw_irq number provided from phyp firmware.
Request an irq assigned our Sub-CRQ interrupt handler. Unmap these irqs at
Sub-CRQ teardown.

Link: https://lore.kernel.org/r/20210114203148.246656-12-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Define Sub-CRQ interrupt handler routine

Simple handler that calls Sub-CRQ drain routine directly.

Link: https://lore.kernel.org/r/20210114203148.246656-11-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Add handlers to drain and complete Sub-CRQ responses

The logic for iterating over the Sub-CRQ responses is similiar to that of
the primary CRQ. Add the necessary handlers for processing those responses.

Link: https://lore.kernel.org/r/20210114203148.246656-10-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Add Sub-CRQ IRQ enable/disable routine

Each Sub-CRQ has its own interrupt. A hypercall is required to toggle the
IRQ state. Provide the necessary mechanism via a helper function.

Link: https://lore.kernel.org/r/20210114203148.246656-9-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Add alloc/dealloc routines for SCSI Sub-CRQ Channels

Allocate a set of Sub-CRQs in advance. During channel setup the client and
VIOS negotiate the number of queues the VIOS supports and the number that
the client desires to request. Its possible that the final channel
resources allocated is less than requested, but the client is still
responsible for sending handles for every queue it is hoping for.

Also, provide deallocation cleanup routines.

Link: https://lore.kernel.org/r/20210114203148.246656-8-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Add Subordinate CRQ definitions

Subordinate Command Response Queues (Sub CRQ) are used in conjunction with
the primary CRQ when more than one queue is needed by the virtual I/O
adapter. Recent phyp firmware versions support Sub CRQ's with ibmvfc
adapters. This feature is a prerequisite for supporting multiple hardware
backed submission queues in the vfc adapter.

The Sub CRQ command element differs from the standard CRQ in that it is
32bytes long as opposed to 16bytes for the latter. Despite this extra
16bytes the ibmvfc protocol will use the original CRQ command element
mapped to the first 16bytes of the Sub CRQ element initially.

Add definitions for the Sub CRQ command element and queue.

Link: https://lore.kernel.org/r/20210114203148.246656-7-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Define hcall wrapper for registering a Sub-CRQ

Sub-CRQs are registred with firmware via a hypercall. Abstract that
interface into a simpler helper function.

Link: https://lore.kernel.org/r/20210114203148.246656-6-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Add size parameter to ibmvfc_init_event_pool()

With the upcoming addition of Sub-CRQs the event pool size may vary
per-queue.

Add a size parameter to ibmvfc_init_event_pool() such that different size
event pools can be requested by ibmvfc_alloc_queue().

Link: https://lore.kernel.org/r/20210114203148.246656-5-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Init/free event pool during queue allocation/free

The event pool and CRQ used to be separate entities of the adapter host
structure and as such were allocated and freed independently of each
other. Recent work as defined a generic queue structure with an event pool
specific to each queue. As such the event pool for each queue shouldn't be
allocated/freed independently, but instead performed as part of the queue
allocation/free routines.

Move the calls to ibmvfc_event_pool_{init|free} into
ibmvfc_{alloc|free}_queue respectively. The only functional change here is
that the CRQ cannot be released in ibmvfc_remove until after the event pool
has been successfully purged since releasing the queue will also free the
event pool.

Link: https://lore.kernel.org/r/20210114203148.246656-4-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Move event pool init/free routines

The next patch in this series reworks the event pool allocation calls to
happen within the individual queue allocation routines instead of as
independent calls.

Move the init/free routines earlier in ibmvfc.c to prevent undefined
reference errors when calling these functions from the queue allocation
code. No functional change.

Link: https://lore.kernel.org/r/20210114203148.246656-3-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvfc: Add vhost fields and defaults for MQ enablement

Introduce several new vhost fields for managing MQ state of the adapter as
well as initial defaults for MQ enablement.

Link: https://lore.kernel.org/r/20210114203148.246656-2-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Protect PM ops and err_handler from user access through sysfs

User layer may access sysfs nodes when system PM ops or error handling is
running. This can cause various problems. Rename eh_sem to host_sem and use
it to protect PM ops and error handling from user layer intervention.

Link: https://lore.kernel.org/r/1610594010-7254-3-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Fix a possible NULL pointer issue

During system resume/suspend, hba could be NULL. In this case, do not touch
eh_sem.

Fixes: 88a92d6ae4fe ("scsi: ufs: Serialize eh_work with system PM events and async scan")
Link: https://lore.kernel.org/r/1610594010-7254-2-git-send-email-cang@codeaurora.org
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: MAINTAINERS: Remove intel-linux-scu@intel.com for INTEL C600 SAS DRIVER

The mail address intel-linux-scu@intel.com bounces. Remove it.

Link: https://lore.kernel.org/r/1610449890-198089-1-git-send-email-john.garry@huawei.com
Cc: Ahmed S. Darwish <a.darwish@linutronix.de>
Cc: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Acked-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: Remove unnecessary devm_kfree()

The memory allocated with devm_kzalloc() is freed automatically no need to
explicitly call devm_kfree(). Delete it and save some instruction cycles.

Link: https://lore.kernel.org/r/20210112092128.19295-1-huobean@gmail.com
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Simplify bool comparison

Fix the following coccicheck warning:

./drivers/scsi/lpfc/lpfc_bsg.c:5392:5-29: WARNING: Comparison to bool

Link: https://lore.kernel.org/r/1610439893-64872-1-git-send-email-abaci-bugfix@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: WB is only available on LUN #0 to #7

Kernel stack violation when getting unit_descriptor/wb_buf_alloc_units from
rpmb LUN. The reason is that the unit descriptor length is different per
LU.

The length of Normal LU is 45 while the one of rpmb LU is 35.

int ufshcd_read_desc_param(struct ufs_hba *hba, ...)
{
param_offset=41;
param_size=4;
buff_len=45;
...
buff_len=35 by rpmb LU;

if (is_kmalloc) {
/* Make sure we don't copy more data than available */
if (param_offset + param_size > buff_len)
param_size = buff_len - param_offset;
--> param_size = 250;
memcpy(param_read_buf, &desc_buf[param_offset], param_size);
--> memcpy(param_read_buf, desc_buf+41, 250);

[  141.868974][ T9174] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: wb_buf_alloc_units_show+0x11c/0x11c
}
}

Link: https://lore.kernel.org/r/20210111095927.1830311-1-jaegeuk@kernel.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Update version to 10.02.00.105-k

Link: https://lore.kernel.org/r/20210111093134.1206-8-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Enable NVMe CONF (BIT_7) when enabling SLER

Enable NVMe confirmation bit in PRLI.

Link: https://lore.kernel.org/r/20210111093134.1206-7-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix mailbox Ch erroneous error

Mailbox Ch/dump ram extend expects mb register 10 to be set. If not
set/clear, firmware can pick up garbage from previous invocation of this
mailbox. Example: mctp dump can set mb10.  On subsequent flash read which
use mailbox cmd Ch, mb10 can retain previous value.

Link: https://lore.kernel.org/r/20210111093134.1206-6-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Wait for ABTS response on I/O timeouts for NVMe

FW needs to wait for an ABTS response before completing the I/O.

Link: https://lore.kernel.org/r/20210111093134.1206-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bikash Hazarika <bhazarika@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Move some messages from debug to normal log level

This change will aid in debugging issues arising because of dropped frame,
DIF errors, queue full etc where debug level is not set.

Link: https://lore.kernel.org/r/20210111093134.1206-4-njavali@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Add error counters to debugfs node

Display error counters via debugfs node.

Link: https://lore.kernel.org/r/20210111093134.1206-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Implementation to get and manage host, target stats and initiator port

This statistics will help in debugging process and checking specific error
counts. It also provides a capability to isolate the port or bring it out
of isolation.

Link: https://lore.kernel.org/r/20210111093134.1206-2-njavali@marvell.com
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedf: Simplify bool comparison

Fix the following coccicheck warning:

./drivers/scsi/qedf/qedf_main.c:3716:5-31: WARNING: Comparison to bool

Link: https://lore.kernel.org/r/1610357368-62866-1-git-send-email-abaci-bugfix@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aha1542: Fix multi-line comment style

Some comments in this driver don't comply with the preferred multi-line
comment style, as reported by 'scripts/checkpatch.pl':

WARNING: Block comments use * on subsequent lines
WARNING: Block comments use a trailing */ on a separate line

Fix those comments, along with the (unreported for some reason?) starts of
the multi-line comments not being /* on their own line...

Link: https://lore.kernel.org/r/08c231e5-d86f-9d0b-19ac-ad46fa0c0b58@omprussia.ru
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aha1542: Kill trailing whitespace

Some source lines (mostly the comments) in this driver end with spaces, as
reported by 'scripts/checkpatch.pl'. Trim these lines.

Link: https://lore.kernel.org/r/59829052-4932-4ea3-b504-857bbb19e6a0@omprussia.ru
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aha1542: Clarify 'struct ccb' comments

This driver's original authors did pretty bad job of documenting the
Command Control Block (CCB) structure -- especially its 2nd byte, where the
bit numbers were completely left out. Sync up the 'struct ccb' comments to
the Adaptec AHA-154xA manual.

Link: https://lore.kernel.org/r/17a7be14-a9d2-9822-bb3e-1d7385f486b0@omprussia.ru
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: A tad optimization in query upiu trace

Remove a redundant if clause in ufshcd_add_query_upiu_trace.

Link: https://lore.kernel.org/r/20210110084618.189371-1-avri.altman@wdc.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: file: Don't zero iter before iov_iter_bvec

iov_iter_bvec() initialises iterators well, no need to pre-zero it
beforehand as done in fd_execute_rw_aio(). Compilers can't optimise it out
and generate extra code for that (confirmed with assembly).

Link: https://lore.kernel.org/r/34cd22d6cec046e3adf402accb1453cc255b9042.1610207523.git.asml.silence@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Log SATA IOMB completion status on failure

Added a log message in SATA completion path to capture the status of failed
command. If the status does not match any expected status, another message
will be logged.

On IO failure with known status, the log message will be:

  [ 1712.951735] pm80xx0:: mpi_sata_completion 2269: IO failed device_id 16385 status 0x1 tag XX

If the firmware returns unexpected status, a message of the following
format will be logged:

  [ 1712.951735] pm80xx0:: mpi_sata_completion XXXX: Unknown status device_id XXXXX status 0xX tag XX

Link: https://lore.kernel.org/r/20210109123849.17098-8-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vishakha Channapattan <vishakhavc@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Simultaneous poll for all FW readiness

In check_fw_ready() we first wait for ILA to come up and then we wait for
RAAE to come up and IOPs and so on. This is a sequential check.  Because of
this, ILA image seems to be not ready in the allocated time and so the
driver marks it as "not ready" and then moves on to other FW images.

ILA does become ready eventually, but is not checked again. The driver
concludes that FW is not ready when it actually is.

Instead of sequentially polling each image, we keep polling for all images
to be ready. The timeout for the polling has been set to the sum of what
was used for each individual image.

Link: https://lore.kernel.org/r/20210109123849.17098-7-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Bhavesh Jashnani <bjashnani@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Fix driver fatal dump failure

The function pm80xx_get_fatal_dump() has two issues that result in the
fatal dump not being able to complete successfully.

 1. Trying to collect fatal_logs from the application fails because we are
    not shifting the MEMBASE-II register properly. Once we read 64K region
    of data we have to shift the MEMBASE-II register and read the next
    chunk. Only then would we be able to get complete data.

 2. If a timeout occurs, our application will get stuck.

Link: https://lore.kernel.org/r/20210109123849.17098-6-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Fix missing tag_free in NVMD DATA req

Tag was not freed in NVMD get/set data request failure scenario. This
caused a tag leak each time a request failed.

Link: https://lore.kernel.org/r/20210109123849.17098-5-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Check main config table address

The driver initializes main configuration, general status, inbound queue
and outbound queue table addresses based on a value read from
MSGU_SCRATCH_PAD_0 register.

We should validate these addresses before dereferencing them.

Adds two validations:

 1. Check if main configuration table offset lies within the pcibar
    mapped

 2. Check if first dword of main configuration table reads "PMCS"

There are two calls to init_pci_device_addresses() done during
pm8001_pci_probe() in this sequence:

 1. First inside chip_soft_rst, where if init_pci_device_addresses fails we
    will go ahead assuming MPI state is not ready and reset the device as
    long as bootloader is okay.  This gives chance to second call of
    init_pci_device_addresses to set up the addresses after reset.

 2. The second call is via pm80xx_chip_init, after soft reset is done and
    firmware is checked to be ready. Once that is done we are safe to go
    ahead and initialize default table values and use them.

Tests:

 1. Enabled debugging logs and observed no issues during initialization,
    with a controller with no issues:

    pm80xx0:: pm8001_setup_msix 1034: pci_alloc_irq_vectors request ret:64 no of intr 64
    pm80xx0:: init_pci_device_addresses 917: Scratchpad 0 Offset: 0x2000 value 0x40002000
    pm80xx0:: init_pci_device_addresses 925: Scratchpad 0 PCI BAR: 0
    pm80xx0:: init_pci_device_addresses 952: VALID main config signature 0x53434d50
    pm80xx0:: init_pci_device_addresses 975: GST OFFSET 0xc4
    pm80xx0:: init_pci_device_addresses 978: INBND OFFSET 0x20000128
    pm80xx0:: init_pci_device_addresses 981: OBND OFFSET 0x24000928
    pm80xx0:: init_pci_device_addresses 984: IVT OFFSET 0x8001408
    pm80xx0:: init_pci_device_addresses 987: PSPA OFFSET 0x8001608
    pm80xx0:: init_pci_device_addresses 991: addr - main cfg (ptrval) general status (ptrval)
    pm80xx0:: init_pci_device_addresses 995: addr - inbnd (ptrval) obnd (ptrval)
    pm80xx0:: init_pci_device_addresses 999: addr - pspa (ptrval) ivt (ptrval)
    pm80xx0:: pm80xx_chip_soft_rst 1446: reset register before write : 0x0
    pm80xx0:: pm80xx_chip_soft_rst 1478: reset register after write 0x40
    pm80xx0:: pm80xx_chip_soft_rst 1544: SPCv soft reset Complete
    pm80xx0:: init_pci_device_addresses 917: Scratchpad 0 Offset: 0x2000 value 0x40002000
    pm80xx0:: init_pci_device_addresses 925: Scratchpad 0 PCI BAR: 0
    pm80xx0:: init_pci_device_addresses 952: VALID main config signature 0x53434d50
    pm80xx0:: init_pci_device_addresses 975: GST OFFSET 0xc4
    pm80xx0:: init_pci_device_addresses 978: INBND OFFSET 0x20000128
    pm80xx0:: init_pci_device_addresses 981: OBND OFFSET 0x24000928
    pm80xx0:: init_pci_device_addresses 984: IVT OFFSET 0x8001408
    pm80xx0:: init_pci_device_addresses 987: PSPA OFFSET 0x8001608
    pm80xx0:: init_pci_device_addresses 991: addr - main cfg (ptrval) general status (ptrval)
    pm80xx0:: init_pci_device_addresses 995: addr - inbnd (ptrval) obnd (ptrval)
    pm80xx0:: init_pci_device_addresses 999: addr - pspa (ptrval) ivt (ptrval)
    pm80xx0:: pm80xx_chip_init 1329: MPI initialize successful!

 2. Tested controller with firmware known to have initialization issue and
    observed no crashes with this fix:

    pm80xx 0000:01:00.0: pm80xx: driver version 0.1.38
    pm80xx 0000:01:00.0: Removing from 1:1 domain
    pm80xx 0000:01:00.0: Requesting non-1:1 mappings
    pm80xx0:: init_pci_device_addresses 948: BAD main config signature 0x0
    pm80xx0:: mpi_uninit_check 1365: Failed to init pci addresses
    pm80xx0:: pm80xx_chip_soft_rst 1435: MPI state is not ready scratch:0:8:62a01000:0
    pm80xx0:: pm80xx_chip_soft_rst 1518: Firmware is not ready!
    pm80xx0:: pm80xx_chip_soft_rst 1532: iButton Feature is not Available!!!
    pm80xx0:: pm80xx_chip_init 1301: Firmware is not ready!
    pm80xx0:: pm8001_pci_probe 1215: chip_init failed [ret: -16]
    pm80xx: probe of 0000:01:00.0 failed with error -16
    pm80xx 0000:07:00.0: pm80xx: driver version 0.1.38
    pm80xx 0000:07:00.0: Removing from 1:1 domain
    pm80xx 0000:07:00.0: Requesting non-1:1 mappings
    scsi host6: pm80xx
    pm80xx1:: pm8001_setup_sgpio 5568: failed sgpio_req timeout
    pm80xx1:: mpi_phy_start_resp 3447: phy start resp status:0x0, phyid:0x0
    pm80xx 0000:08:00.0: pm80xx: driver version 0.1.38
    pm80xx 0000:08:00.0: Removing from 1:1 domain
    pm80xx 0000:08:00.0: Requesting non-1:1 mappings

 3. Without this fix we observe crash on the same controller:

    pm80xx 0000:01:00.0: pm80xx: driver version 0.1.38
    pm80xx 0000:01:00.0: Removing from 1:1 domain
    pm80xx 0000:01:00.0: Requesting non-1:1 mappings
    [<ffffffffc0451b3b>] pm80xx_chip_soft_rst+0x6b/0x4c0 [pm80xx]
    [<ffffffffc043a933>] pm8001_pci_probe+0xa43/0x1630 [pm80xx]
    RIP: 0010:pm80xx_chip_soft_rst+0x71/0x4c0 [pm80xx]
    [<ffffffffc0451b3b>] ? pm80xx_chip_soft_rst+0x6b/0x4c0 [pm80xx]
    [<ffffffffc043a933>] pm8001_pci_probe+0xa43/0x1630 [pm80xx]
    pm80xx0:: mpi_uninit_check 1339: TIMEOUT:IBDB value/=2
    pm80xx0:: pm80xx_chip_soft_rst 1387: MPI state is not ready scratch:0:8:62a01000:0
    pm80xx0:: pm80xx_chip_soft_rst 1470: Firmware is not ready!
    pm80xx0:: pm80xx_chip_soft_rst 1484: iButton Feature is not Available!!!
    pm80xx0:: pm80xx_chip_init 1266: Firmware is not ready!
    pm80xx0:: pm8001_pci_probe 1207: chip_init failed [ret: -16]
    pm80xx: probe of 0000:01:00.0 failed with error -16

Link: https://lore.kernel.org/r/20210109123849.17098-4-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Check for fatal error

When the controller runs into a fatal error, commands get stuck due to no
response. If the controller is in fatal error state, abort requests issued
to the controller get stuck too.

Check the controller state for fatal error conditions.

Link: https://lore.kernel.org/r/20210109123849.17098-3-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm80xx: Do not busy wait in MPI init check

We do not need to busy wait during mpi_init_check() since it is not being
invoked in atomic context. mpi_init_check() is being called from
pm8001_pci_resume(), pm8001_pci_probe(). Hence we are replacing udelay with
msleep.

Link: https://lore.kernel.org/r/20210109123849.17098-2-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs-qcom: Fix ufs RST_n spec violation

According to the spec (JESD220E chapter 7.2), while powering off/on the ufs
device, RST_n signal should be between VSS(Ground) and VCCQ/VCCQ2.

Link: https://lore.kernel.org/r/1610103385-45755-3-git-send-email-ziqichen@codeaurora.org
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ziqi Chen <ziqichen@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: core: Fix ufs clk specs violation

According to the spec (JESD220E chapter 7.2), while powering off/on the ufs
device, REF_CLK signal should be between VSS(Ground) and VCCQ/VCCQ2.

Link: https://lore.kernel.org/r/1610103385-45755-2-git-send-email-ziqichen@codeaurora.org
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ziqi Chen <ziqichen@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: isci: Remove the unneeded variable "status"

The variable 'status' is being initialized with SCI_SUCCESS and never
updated later with a new value. The initialization is redundant and can be
removed.

Link: https://lore.kernel.org/r/1609311860-102820-1-git-send-email-abaci-bugfix@linux.alibaba.com
Reported-by: Abaci <abaci@linux.alibaba.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: ufs-debugfs: Add error counters

People testing have a need to know how many errors might be occurring over
time. Add error counters and expose them via debugfs.

A module initcall is used to create a debugfs root directory for
ufshcd-related items. In the case that modules are built-in, then
initialization is done in link order, so move ufshcd-core to the top of the
Makefile.

Link: https://lore.kernel.org/r/20210107072538.21782-1-adrian.hunter@intel.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: storvsc: Validate length of incoming packet in storvsc_on_channel_callback()

Check that the packet is of the expected size at least, don't copy data
past the packet.

Link: https://lore.kernel.org/r/20201217203321.4539-4-parri.andrea@gmail.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Reported-by: Saruhan Karademir <skarade@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: storvsc: Resolve data race in storvsc_probe()

vmscsi_size_delta can be written concurrently by multiple instances of
storvsc_probe(), corresponding to multiple synthetic IDE/SCSI devices;
cf. storvsc_drv's probe_type == PROBE_PREFER_ASYNCHRONOUS.  Change the
global variable vmscsi_size_delta to per-synthetic-IDE/SCSI-device.

Link: https://lore.kernel.org/r/20201217203321.4539-3-parri.andrea@gmail.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Suggested-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: storvsc: Fix max_outstanding_req_per_channel for Win8 and newer

Current code overestimates the value of max_outstanding_req_per_channel for
Win8 and newer hosts, since vmscsi_size_delta is set to the initial value
of sizeof(vmscsi_win8_extension) rather than zero.  This may lead to wrong
decisions when using ring_avail_percent_lowater equals to zero.  The
estimate of max_outstanding_req_per_channel is 'exact' for Win7 and older
hosts.  A better choice, keeping the algorithm for the estimation simple,
is to err the other way around, i.e., to underestimate for Win7 and older
but to use the exact value for Win8 and newer.

Link: https://lore.kernel.org/r/20201217203321.4539-2-parri.andrea@gmail.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Suggested-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Update lpfc version to 12.8.0.7

Update lpfc version to 12.8.0.7

Link: https://lore.kernel.org/r/20210104180240.46824-16-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>