iio: adc: ad7768-1: reorganize driver headers

Remove kernel.h since it adds a lot of unnecessary dependencies.
Add specific headers to ensure all functions and macros used in the driver
are directly declared.

Suggested-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/1f7677d31a0165cb30d7eb3b4d613e1337937f9a.1746662899.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: bmp280: zero-init buffer

Zero-initialize the buffer used with iio_push_to_buffers_with_ts(). The
struct used for the buffer has holes in it, so we need to make sure that
the holes are zeroed out rather than containing uninitialized data from
the stack.

Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-iio/aBoBR5D1UMjsSUfZ@stanley.mountain/
Fixes: 872c8014e05e ("iio: pressure: bmp280: drop sensor_data array")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250506-iio-pressure-bmp280-zero-init-buffer-v1-1-0935c31558ac@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ssp_sensors: optimalize -> optimize

Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Link: https://patch.msgid.link/5a64aa3034c6127d7587de9b7045a12892c01ee5.1746558529.git.nabijaczleweli@nabijaczleweli.xyz
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

HID: sensor-hub: Fix typo and improve documentation

Includes the following corrections -
 - Changed Measurment -> Measurement
 - Changed clode -> close
 - Gyro -> gyro

Signed-off-by: Chelsy Ratnawat <chelsyratnawat2001@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507055745.4069933-1-chelsyratnawat2001@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: admv1013: replace redundant ternary operator with just len

The variable ret is being assigned a return value and non-zero error
return paths are taken at all stages. At the end of the function ret
is always zero, so the ternary operator checking for zero ret is
redundant and can be replaced with just len instead.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507134502.254736-1-colin.i.king@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: chemical: mhz19b: Fix error code in probe()

Return -ENOMEM if devm_iio_device_alloc() fails.  Don't return success.

Fixes: 4572a70b3681 ("iio: chemical: Add support for Winsen MHZ19B CO2 sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Acked-by: Gyeyoung Baek <gye976@gmail.com>
Link: https://patch.msgid.link/aBtZFLFlr0slcYSi@stanley.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS

Use IIO_DECLARE_BUFFER_WITH_TS() to declare the buffer that gets used
with iio_push_to_buffers_with_ts(). This makes the code a bit easier to
read and understand.

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-7-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS

Use IIO_DECLARE_BUFFER_WITH_TS() to declare the buffer that gets used
with iio_push_to_buffers_with_ts(). This makes the code a bit easier to
read and understand.

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-6-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS

Use IIO_DECLARE_DMA_BUFFER_WITH_TS() to declare the buffer that gets
used with iio_push_to_buffers_with_ts(). This makes the code a bit
easier to read and understand.

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-5-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS

Rename AD4695_MAX_CHANNELS to AD4695_MAX_VIN_CHANNELS. It has been a
point of confusion that this macro is only the voltage input channels
and not all channels.

Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-4-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS

Use IIO_DECLARE_DMA_BUFFER_WITH_TS() to declare the buffer that gets
used with iio_push_to_buffers_with_ts(). This makes the code a bit
easier to read and understand.

Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-3-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros

Add new macros to help with the common case of declaring a buffer that
is safe to use with iio_push_to_buffers_with_ts(). This is not trivial
to do correctly because of the alignment requirements of the timestamp.
This will make it easier for both authors and reviewers.

To avoid double __align() attributes in cases where we also need DMA
alignment, add a 2nd variant IIO_DECLARE_DMA_BUFFER_WITH_TS().

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-2-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: make IIO_DMA_MINALIGN minimum of 8 bytes

Add a condition to ensure that IIO_DMA_MINALIGN is at least 8 bytes.
On some 32-bit architectures, IIO_DMA_MINALIGN is 4. In many cases,
drivers are using this alignment for buffers that include a 64-bit
timestamp that is used with iio_push_to_buffers_with_ts(), which expects
the timestamp to be aligned to 8 bytes. To handle this, we can just make
IIO_DMA_MINALIGN at least 8 bytes.

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-1-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: pressure: zpa2326_spi: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the zpa2326 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-14-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: pressure: ms5611_spi: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the ms5611 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-13-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: pressure: bmp280-spi: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the bmp280 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Since no other SPI settings are changed, we can also remove the call to
spi_setup().

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-12-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: magnetometer: rm3100-spi: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the rm3100 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-11-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: magnetometer: hmc5843_spi: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the hmc5843 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-10-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: adis: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the adis driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-9-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: gyro: adxrs450: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the adxrs450 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-8-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ltc2688: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the ltc2688 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-7-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad5791: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the ad5791 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-6-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad5766: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the ad5766 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-5-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad5761: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the ad5761 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-4-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: chemical: bme680_spi: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the bme680 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Since no other SPI settings are changed, we can also remove the call to
spi_setup().

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-3-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-tsc2046: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the ti-tsc2046 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-2-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad4030: remove bits_per_word = 8

Remove setting bits_per_word = 8 from the ad4030 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-1-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-ads1298: Kconfig: add kfifo dependency to fix module build

Add dependency to Kconfig’s ti-ads1298 because compiling it as a module
failed with an undefined kfifo symbol.

Fixes: 00ef7708fa60 ("iio: adc: ti-ads1298: Add driver")
Signed-off-by: Arthur-Prince <r2.arthur.prince@gmail.com>
Co-developed-by: Mariana Valério <mariana.valerio2@hotmail.com>
Signed-off-by: Mariana Valério <mariana.valerio2@hotmail.com>
Link: https://patch.msgid.link/20250430191131.120831-1-r2.arthur.prince@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ti-adc128s052: Drop variable vref

According to Jonathan, variable reference voltages are very rare. It is
unlikely it is needed, and supporting it makes the code a bit more
complex.

Simplify the driver and drop the variable vref support.

Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/59106e24332743a7f9eb0b13ad6a2f5595ab485a.1745823530.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad4000: Avoid potential double data word read

Currently, SPI-Engine offload module always sends 32-bit data elements to
DMA engine. Appropriately, when set for SPI offloading, the IIO driver uses
32 storagebits for IIO ADC channel buffer elements. However, setting SPI
transfer length according to storagebits (32-bits in case of offload) can
lead to unnecessarily long transfers for ADCs that are 16-bit or less
precision. Adjust AD4000 single-shot read to run transfers of 2 bytes when
that is enough to get all ADC data bits.

Fixes: 59b51edf717b ("iio: adc: ad4000: Add support for SPI offload")
Suggested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/8f765cfd6e93fad4e755dd95d709b7bea2a388e2.1744718916.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: mcp3911: add reset management

Add support for optional HW reset.
If specified, a reset will be asserted during driver probe.

Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-3-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: mcp3911: add reset-gpios

The MCP391X family provides an active low reset signal that is still not
described in the bindings.

Add reset-gpios to the bindings and the example.

Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-2-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: mcp3911: fix device dependent mappings for conversion result registers

The conversion result registers differs between devices. Make sure the
mapping is correct by using a device dependent .get_raw() callback function.

Fixes: 732ad34260d3 ("iio: adc: mcp3911: add support for the whole MCP39xx family")
Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-1-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad4695: use u16 for buffer elements

Change the type of the buffer elements to u16 since we currently only
support 16-bit word size. The code was originally written to also allow
for 32-bit word size when oversampling is enabled, but so far,
oversampling is only implemented when using SPI offload and therefore
doesn't use this buffer.

AD4695_MAX_CHANNEL_SIZE macro is dropped since it no longer adds any
value.

AD4695_MAX_CHANNELS + 2 is changed to AD4695_MAX_CHANNELS + 1 because
previously we were overallocating. AD4695_MAX_CHANNELS is the number of
of voltage channels and + 1 is for the temperature channel.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Link: https://patch.msgid.link/20250428-iio-introduce-iio_declare_buffer_with_ts-v4-2-6f7f6126f1cb@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad3530r: Add driver for AD3530R and AD3531R

The AD3530/AD3530R (8-channel) and AD3531/AD3531R (4-channel) are
low-power, 16-bit, buffered voltage output DACs with software-
programmable gain controls, providing full-scale output spans of 2.5V or
5V for reference voltages of 2.5V. These devices operate from a single
2.7V to 5.5V supply and are guaranteed monotonic by design. The "R"
variants include a 2.5V, 5ppm/°C internal reference, which is disabled
by default.

Support for monitoring internal die temperature, output voltages, and
current of a selected channel via the MUXOUT pin using an external ADC
is currently not implemented.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250429-togreg-v7-3-0af9c543b545@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: dac: Add adi,ad3530r.yaml

Document the AD3530/AD3530R (8-channel) and AD3531/AD3531R (4-channel)
low-power, 16-bit, buffered voltage output DACs with software-
programmable gain controls. They provide full-scale output spans of 2.5V
or 5V for reference voltages of 2.5V. These devices operate on a single
2.7V to 5.5V supply and are guaranteed to be monotonic by design.
The "R" variants include a 2.5V, 5ppm/°C internal reference, which is
disabled by default.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Link: https://patch.msgid.link/20250429-togreg-v7-2-0af9c543b545@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ABI: add new DAC powerdown mode

Add a new powerdown mode for DACs with 7.7kohm and 32kohm resistor
to GND.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Link: https://patch.msgid.link/20250429-togreg-v7-1-0af9c543b545@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

HID: sensor-hub: Fix typo and improve documentation for sensor_hub_remove_callback()

Fixed a typo in "registered" and improved grammar for better readability
and consistency with kernel-doc standards. No functional changes.

Signed-off-by: Chelsy Ratnawat <chelsyratnawat2001@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250502003655.1943000-1-chelsyratnawat2001@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7606: explicit timestamp alignment

Use struct with aligned_s64 timestamp to make timestamp alignment
explicit. Technically, what we have works because for all known
architectures, IIO_DMA_MINALIGN is a multiple of __alignof__(s64).
But this way, we don't have to make people read the comments to know
why there are extra elements in each buffer.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250428-iio-adc-ad7606-fix-buffer-alignment-v1-1-88dfc57e5df0@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

MAINTAINERS: add maintainers for ad4851 driver

Add the ad4851 entry in the MAINTAINERS file.

Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250502100016.26279-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7606_spi: add offload scan mask check

Validate the scan mask when SPI offloading is being used.

Since this family of ADCs is simultaneous sampling, there isn't a way
to selectively disable channels when reading sample data. (Technically,
AD7616 has a sequencer so the driver could have some control, but that
is for another day).

For "regular" IIO triggered buffer reads, this isn't a problem and the
IIO core will demux the data and ignore data from disabled channels.
However, since SPI offloading is done completely in hardware, we don't
have a way to do the same. So before this patch, if less than all
channels were enabled, the data would be misplaced in the buffer.

By adding a check in update_scan_mode, we can fail to enable the buffer
instead of having bad data returned to userspace.

Fixes: e96d35faf357 ("iio: adc: ad7606: add SPI offload support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250502-iio-adc-ad7606_spi-fix-offload-scan-mask-check-v2-1-e70c6d71baa3@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: Add compatible for Dimensity 1200 MT6893

Add a compatible for the Dimensity 1200 (MT6893) SoC; The AUXADC
IP in this chip is fully compatible with the one found in MT8173.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250416120235.147889-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad7293: add adc reference configuration

Add support for configurating the ADC reference (internal/external).

According to the datasheet, the external reference is enabled by
default.

Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250422085529.4407-2-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: dac: ad7293: add vrefin support

Add support for vrefin supply responsible for providing external
reference to the SAR ADC within the part.

Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250422085529.4407-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7091r-base: Remove duplicate code on volatile reg check

Both ad7091r_writeable_reg() and ad7091r_volatile_reg() perform the
same test, checking whether a given 'reg' code is
AD7091R_REG_RESULT or AD7091R_REG_ALERT. As the volatile ad7091r
registers happen to be the only read-only ones, the volatile_reg()
function now returns the negated output of writeable_reg().

Co-developed-by: Bruno Stephan <bruno.stephan@usp.br>
Signed-off-by: Bruno Stephan <bruno.stephan@usp.br>
Co-developed-by: Andre de Lima <aschwarz@usp.br>
Signed-off-by: Andre de Lima <aschwarz@usp.br>
Signed-off-by: Arthur Pilone <art.pilone@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/20250421145534.91146-1-arthurpilone@usp.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: pressure: bmp280: drop sensor_data array

Drop the sensor_data array from struct bmp280_data and replace it using
local structs in each interrupt handler.

The sensor_data array in struct bmp280_data is not used to share data
between functions and isn't used for DMA, so there isn't really a need
to have it in the struct. Instead, we can use the struct pattern for
scan data in each interrupt handler. This has the advantage of allowing
us to see the actual layout of each scan buffer for each different type
of supported sensor. It also avoid juggling values between local
variables and the array which makes the code a bit simpler by avoiding
some extra assignments.

We can also drop the BME280_NUM_MAX_CHANNELS macro as it is no longer
used.

Suggested-by: Jonathan Cameron <jic23@kernel.org>
Link: https://lore.kernel.org/linux-iio/20250421135540.1a667221@jic23-huawei/
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250422-iio-pressure-bmp280-rework-push-to-buffers-v1-1-ee722f29aeca@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

MAINTAINERS: Add WINSEN MHZ19B

Add undersigned as a maintainer for the WINSEN MHZ19B.

Signed-off-by: Gyeyoung Baek <gye976@gmail.com>
Link: https://patch.msgid.link/20250423194100.53934-5-gye976@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: chemical: Add support for Winsen MHZ19B CO2 sensor

Add support for Winsen MHZ19B CO2 sensor.

Datasheet: https://www.winsen-sensor.com/d/files/infrared-gas-sensor/mh-z19b-co2-ver1_0.pdf
Signed-off-by: Gyeyoung Baek <gye976@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250423194100.53934-4-gye976@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: Add device tree support for Winsen MHZ19B CO2 sensor

Add device tree support for Winsen MHZ19B sensor.

Signed-off-by: Gyeyoung Baek <gye976@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250423194100.53934-3-gye976@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: Add Winsen to the vendor prefixes

Add Winsen to the vendor prefixes.

Signed-off-by: Gyeyoung Baek <gye976@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250423194100.53934-2-gye976@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: kxcjk-1013: Deduplicate setup interrupt functions

The contents of kxcjk1013_setup_any_motion_interrupt and
kxcj1013_setup_new_data_interrupt are very similar. Deduplicate these
functions by introducing a generic function named
kxcjk1013_setup_interrupt that has an additional flag indicating if
it's a new data interrupt.

Signed-off-by: Gustavo Vaz <gustavo.vaz@usp.br>
Co-developed-by: Francisco Henriques <franciscolealhenriques@usp.br>
Signed-off-by: Francisco Henriques <franciscolealhenriques@usp.br>
Link: https://patch.msgid.link/20250423204631.16460-1-gustavo.vaz@usp.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: cros_ec_sensors: Flush when changing the FIFO timeout

|hwfifo_timeout| is used by the EC firmware only when new samples are
available.
When the timeout changes, espcially when the new timeout is shorter than
the current one, send the samples waiting in the FIFO to the host.
Inline the call to transmit |hwfifo_timeout| value to the firmware.

Now flush when a sensor is suspended (ODR set to 0) as well.

Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://patch.msgid.link/20250423220506.2061021-1-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: light: zopt2201: Remove code duplication in scale write functions

Consolidate duplicated logic from zopt2201_write_scale_als_by_idx() and
zopt2201_write_scale_uvb_by_idx() into a new generic helper function
zopt2201_write_scale_by_idx(). This function takes an additional
parameter: a pointer to a zopt2201_scale array.

To support this, the previously anonymous and duplicated struct used in
the scale arrays was promoted to a named struct: zopt2201_scale.

This change also corrects an incorrect array access that existed in
zopt2201_write_scale_uvb_by_idx().

Signed-off-by: Beatriz Viana Costa <beatrizvianacosta16@gmail.com>
Co-developed-by: Gabriela Victor <gabevictor333@gmail.com>
Signed-off-by: Gabriela Victor <gabevictor333@gmail.com>
Link: https://patch.msgid.link/20250424002144.23260-1-beatrizvianacosta16@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: PAC1934: fix typo in documentation link

Fix a typo,(PAC1934 -> PAC193X), into the link from an application note
related to the ACPI device definition.

Fixes: 0fb528c8255b ("iio: adc: adding support for PAC193x")
Reported-by: Matteo Martelli <matteomartelli3@gmail.com>
Closes: https://patch.msgid.link/172794015844.2520.11909797050797595912@njaxe.localdomain
Signed-off-by: Marius Cristea <marius.cristea@microchip.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250424-pac1934-doc_link-v1-1-9832445cb270@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: stm32: add oversampling support

Add oversampling support for STM32H7, STM32MP15 & STM32MP13.
STM32F4 ADC has no oversampling feature.

The current support of the oversampling feature aims at increasing the
data SNR, without changing the data resolution.
As the oversampling by itself increases data resolution, a right shift
is applied to keep the initial resolution.
Only the oversampling ratio corresponding to a power of two are
supported here, to get a direct link between right shift and
oversampling ratio. (2^n ratio <=> n right shift)

The oversampling ratio is shared by all channels, whatever channel type.
(e.g. single ended or differential).

Oversampling can be configured using IIO ABI:
- oversampling_ratio_available
- oversampling_ratio

Co-developed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250424151604.626758-1-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad5933: Correct settling cycles encoding per datasheet

The AD5933 datasheet (Table 13) lists the maximum cycles to be 0x7FC
(2044).

Clamp the user input to the maximum effective value of 0x7FC cycles.

Fixes: f94aa354d676 ("iio: impedance-analyzer: New driver for AD5933/4 Impedance Converter, Network Analyzer")
Cc: stable@vger.kernel.org
Signed-off-by: Gabriel Shahrouzi <gshahrouzi@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/20250420013009.847851-1-gshahrouzi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: orientation: hid-sensor-rotation: remove unnecessary alignment

Remove __aligned(16) in the scan data struct in the hid-sensor-rotation
driver. There is nothing in the code that requires this alignment.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250418-iio-orientation-hid-sensor-rotation-remove-alignment-v1-1-6da68eae7ecf@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: hx711: use struct with aligned_s64 timestamp

Use a struct with aligned s64_timestamp instead of a padded array for
the buffer used for iio_push_to_buffers_with_ts(). This makes it easier
to see the correctness of the size and alignment of the buffer.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250418-iio-prefer-aligned_s64-timestamp-v1-3-4c6080710516@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: adxl345: set the tap suppress bit permanently

Set the suppress bit feature to the double tap detection, whenever
double tap is enabled. This impedes the suppress bit dangling in any
state, and thus varying in sensitivity for double tap detection.

Any tap event is defined by a rising signal edge above threshold, i.e.
duration time starts counting; and the falling edge under threshold
within duration time, i.e. then the tap event is issued. This means
duration is used individually for each tap event.

For double tap detection after a single tap, a latency time needs to be
specified. Usually tap events, i.e. spikes above and returning below
threshold will be ignored within latency. After latency, the window
time starts counting for a second tap detection which has to happen
within a duration time.

If the suppress bit is not set, spikes within latency time are ignored.
Setting the suppress bit will invalidate the double tap function. The
sensor will thus be able to save the window time for double tap
detection, and follow a more strict definition of what signal qualifies
for a double tap.

In a summary having the suppress bit set, fewer signal spikes will be
considered as double taps. This is an optional add on to double tap,
thus a separate patch.

Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250414184245.100280-5-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: adxl345: add double tap feature

Add the double tap feature of the sensor. The interrupt handler needs
to catch and forward the event to the IIO channel. The single tap
implementation now is extended to deal with double tap as well.

Doubletap introduces window and latency times, both in us. Since both
times are scaled, the 8-bit register value is stored in hardware,
where the scaled value in [us] is stored as member variable.

Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250414184245.100280-4-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: adxl345: add single tap feature

Add the single tap feature with a threshold in 62.5mg/LSB points and a
scaled duration in us. Keep singletap threshold in regmap cache but
the scaled value of duration in us as member variable.

Both use IIO channels for individual enable of the x/y/z axis. Initializes
threshold and duration with reasonable content. When an interrupt is
caught it will be pushed to the according IIO channel.

Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250414184245.100280-3-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: adxl345: introduce adxl345_push_event function

Move the fifo handling into a separate function. This is a preparation
for a generic handling of the interrupt status register results. The
function is supposed to handle particular sensor events, and later to
forward them to the iio channel. This is needed to read out the interrupt
status register.

The function shall return occurring errors, if any, or 0 in case of
handled events or read fifo content. Thus migrate fifo read-out and push
fifo content to iio channels into this function to be built up with
additional event handling.

Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250414184245.100280-2-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad5592r: Delete stray unlock in ad5592r_write_raw()

This code was converted to use guard locks but one of the unlocks was
accidentally overlooked.  Delete it.

Fixes: 135e101f4dd6 ("iio: dac: ad5592r: use lock guards")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/Z_-P7bsD3KL5K25R@stanley.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: frequency: ad9832: Remove unused parameter from data documentation

This is a leftover from the patch: commit 566564e80b0e ("staging: iio:
ad9832: use clock framework for clock reference").

The AD9832 driver uses the Common Clock Framework (CCF) to obtain the
master clock (MCLK) frequency rather than relying on a frequency value
passed from platform data.

Signed-off-by: Gabriel Shahrouzi <gshahrouzi@gmail.com>
Link: https://patch.msgid.link/20250417173333.607844-1-gshahrouzi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: frequency: ad9832: Use FIELD_PREP macro to set bit fields

Use bitfield and bitmask macros to clearly specify AD9832 SPI
command fields to make register write code more readable.

Suggested-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Siddharth Menon <simeddon@gmail.com>
Link: https://patch.msgid.link/20250416140259.13431-1-simeddon@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: addac: ad74413r: use aligned_s64 for timestamp

Follow the pattern of other drivers and use aligned_s64 for the
timestamp. Technically there was no issue here since
AD74413R_FRAME_SIZE * AD74413R_CHANNEL_MAX == 16 and IIO_DMA_MINALIGN
is always a multiple of 8. But best to conform in case someone copies
this to new code and then tweaks something.

Also move the unaligned.h header while touching this since it was the
only one not in alphabetical order.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250417-iio-more-timestamp-alignment-v1-3-eafac1e22318@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: mt6360-adc: use aligned_s64 for timestamp

Follow the pattern of other drivers and use aligned_s64 for the
timestamp. This will ensure that the timestamp is correctly aligned on
all architectures. It also ensures that the struct itself it also 8-byte
aligned so we can drop the explicit __aligned(8) attribute.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250417-iio-more-timestamp-alignment-v1-2-eafac1e22318@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: magnetometer: Use iio_push_to_buffers_with_ts() to provide length for runtime checks.

This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur.  Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-21-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: pressure: Use iio_push_to_buffers_with_ts() to provide length for runtime checks.

This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur.  Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.

Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com> # ROHM BM1390
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-20-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: pressure: zpa2326: Use aligned_s64 for the timestamp

On x86_32 s64 fields are only 32-bit aligned.  Hence force the alignment of
the field and padding in the structure by using aligned_s64 instead.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-19-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: proximity: Use iio_push_to_buffers_with_ts() to provide length for runtime checks.

This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-18-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: proximity: irsd200: Use a struct for scan and iio_push_to_buffers_with_ts()

The driver previously used an array of two s64, then type cast the
pointer to write an s16 to the start. The code is made more readable
using a structure.  At the same time switch to the new
iio_push_to_buffers_with_ts() helper to enable runtime checking of the
size of the source buffer.

Note that this approach uses a structure with holes, so use memset()
to ensure those do not contain old kernel data as this data is passed
to userspace.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-17-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: resolver: Use iio_push_to_buffers_with_ts() to provide length for runtime checks.

This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur.  Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-16-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: temperature: Use iio_push_to_buffers_with_ts() to provide length for runtime checks.

This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur.  Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-15-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: chemical: Use iio_push_to_buffers_with_ts() to provide length for runtime checks.

This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur.  Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-13-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: hid: Use iio_push_to_buffers_with_ts() to provide length for runtime checks.

This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. For this case, the length being provided
is already passed into the caller function so reuse that.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-12-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: Use iio_push_to_buffers_with_ts() to provide length for runtime checks.

This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur.  Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-11-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Use iio_push_to_buffers_with_ts() to provide length for runtime checks.

This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur.  Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-10-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-ads131e08: Use new iio_push_to_buffers_with_ts() to provide length sanity check.

By providing the size of the buffer used, runtime checks can be performed
to ensure not overrun.

Also change the pushed data pointer to be that of the structure that also
contains the timestamp.  Not an actual bug but semantically incorrect to
push the channel data when we want the storage with the timestamp as well.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-9-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dummy: Switch to iio_push_to_buffers_with_ts() and provide size of storage

Provide the storage size so that the helper can sanity check that it
is large enough for the configured channels.

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-8-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dummy: Use a fixed structure to build up scan to push to buffers.

It has long been discouraged for drivers to make use of iio_dev->scan_bytes
directly as that is an implementation detail of the core. As such our
example driver should definitely not be doing so.

In order to illustrate the more complex case, where a DMA safe buffer is
needed, continue to kzalloc() the storage (but with a structure definition
to provide an explicit data layout). Also add comments on when a DMA safe
buffer is necessary and the two common ways of obtaining one.

Whilst we have a mixture of signed and unsigned channels, the unsigned
channels have ranges that can be stored in a signed value - hence
use signed storage for all channels, simplifying the structure definition.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-7-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: introduced iio_push_to_buffers_with_ts() that takes a data_total_len argument.

Check that data_total_len argument against iio_dev->scan_bytes.

The size needs to be at least as big as the scan. It can be larger,
which is typical if only part of fixed sized storage is used due to
a subset of channels being enabled.

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-6-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

docs: iio: ad3552r: fix malformed table

Fix malformed table.

Fixes: ede84c455659 ("docs: iio: add documentation for ad3552r driver")
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250415-wip-bl-ad3552r-fix-doc-table-v1-1-717ffd320c9d@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: normalize array sentinel style

Use `\t(\{ ?\},|\{\}|\{\s*/\*.*\*/\s*\},?)$` regex to find and replace
the array sentinel in all IIO drivers to the same style.

For some time, we've been trying to consistently use `{ }` (no trailing
comma, no comment, one space between braces) for array sentinels in the
IIO subsystem. Still nearly 50% of existing code uses a different style.
To save reviewers from having to request this trivial change as
frequently, let's normalize the style in all existing IIO drivers.
At least when code is copy/pasted to new drivers, the style will be
consistent.

Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250411-iio-sentinel-normalization-v1-1-d293de3e3d93@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7768-1: Move buffer allocation to a separate function

This change moves the buffer allocation and related trigger allocation
in a separate function, making space for adding another type of iio
buffer if needed.

Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/11c1777b406875ce1a7216dc4b094ff99af8da7f.1744325346.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7768-1: Add reset gpio

Implement asynchronous hardware reset GPIO.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Co-developed-by: Jonathan Santos <Jonathan.Santos@analog.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/25a413babeddf29583f1c26abf4234dfd606a595.1744325346.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7768-1: convert driver to use regmap

Convert the AD7768-1 driver to use the regmap API for register
access. This change simplifies and standardizes register interactions,
reducing code duplication and improving maintainability.

Create two regmap configurations, one for 8-bit register values and
other for 24-bit register values.

Since we are using regmap now, define the remaining registers from 0x32
to 0x34.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/aec9e5452c1ac16d5379a80dfce97c00d85614a2.1744325346.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad_sigma_delta: Fix use of uninitialized status_pos

Fix Smatch-detected issue:
drivers/iio/adc/ad_sigma_delta.c:604 ad_sd_trigger_handler() error:
uninitialized symbol 'status_pos'.

The variable `status_pos` was only initialized in specific switch cases
(1, 2, 3, 4), which could leave it uninitialized if `reg_size` had an
unexpected value.

Fix by adding a default case to the switch block to catch unexpected
values of `reg_size`. Use `dev_err_ratelimited()` for error logging and
`goto irq_handled` instead of returning early.

Signed-off-by: Purva Yeshi <purvayeshi550@gmail.com>
Link: https://patch.msgid.link/20250410170408.8585-1-purvayeshi550@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad3552r-hs: add support for internal ramp

The ad3552r can be feeded from the HDL controller by an internally
generated 16bit ramp, useful for debug pourposes. Add debugfs a file
to enable or disable it.

Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250409-wip-bl-ad3552r-fixes-v5-5-fb429c3a6515@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: adi-axi-dac: add data source get

Add data source getter.

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250409-wip-bl-ad3552r-fixes-v5-4-fb429c3a6515@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: backend: add support for data source get

Add backend support for getting the data source used.

The ad3552r HDL implements an internal ramp generator, so adding the
getter to allow data source get/set by debugfs.

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250409-wip-bl-ad3552r-fixes-v5-3-fb429c3a6515@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

docs: iio: add documentation for ad3552r driver

Add documentation for ad3552r driver, needed to describe the high-speed
driver debugfs attributes and shows how the user may use them.

Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250409-wip-bl-ad3552r-fixes-v5-2-fb429c3a6515@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: adi-axi-dac: add cntrl chan check

Add validity check on CNTRL_X channels (valid as 0 to 15).

Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250409-wip-bl-ad3552r-fixes-v5-1-fb429c3a6515@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: inv_icm42600: switch to use generic name irq get

Use generic fwnode_irq_get_byname() for getting interrupt pin using
interrupt name. Only INT1 is supported by the driver currently.

If not found fallback to first defined interrupt to keep compatibility.

Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://patch.msgid.link/20250410-iio-imu-inv-icm42600-rework-interrupt-using-names-v4-2-19e4e2f8f7eb@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: imu: icm42600: add interrupt naming support

Add interrupt-names field for specifying interrupt pin configured.

Chips are supporting up to 2 interrupt pins with configurable interrupt
sources. Change interrupt to support 1 or 2 entries.

Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250410-iio-imu-inv-icm42600-rework-interrupt-using-names-v4-1-19e4e2f8f7eb@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

MAINTAINERS: A driver for TI/ROHM ADCs

Add undersigned as a maintainer for the ti-adc128s052.c which supports a
few TI's ADCs and the ROHM Semiconductor BD79704 ADC.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/b303bf42b84e7ab143ff6a4a810f7d788e210b86.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-adc128s052: Support ROHM BD79104

The ROHM BD79104 ADC has identical SPI communication logic as the
ti-adc128s052. Eg, SPI transfer should be 16 clk cycles, conversion is
started when the CS is pulled low, and channel selection is done by
writing the channel ID after two zero bits. Data is contained in
big-endian format in the last 12 bits.

The BD79104 has two input voltage pins. Data sheet uses terms "vdd" and
"iovdd". The "vdd" is used also as an analog reference voltage. Hence
the driver expects finding these from the device-tree, instead of having
the "vref" only as TI's driver.

NOTE: The TI's data sheet[1] does show that the TI's IC does actually
have two voltage inputs as well. Pins are called Va (analog reference)
and Vd (digital supply pin) - but I keep the existing driver behaviour
for the TI's IC "as is", because I have no HW to test changes, and
because I have no real need to touch it.

NOTE II: The BD79104 requires SPI MODE 3.

NOTE III: I used evaluation board "BD79104FV-EVK-001" made by ROHM. With
this board I had to drop the SPI speed below the 20M which is mentioned
in the data-sheet [2]. This, however, may be a limitation of the EVK
board, not the component itself.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Datasheet: https://www.ti.com/lit/ds/symlink/adc128s052.pdf # [1]
Datasheet: https://fscdn.rohm.com/en/products/databook/datasheet/ic/data_converter/dac/bd79104fv-la-e.pdf # [2]
Link: https://patch.msgid.link/36ffa72cbdf8dbbdf1e612040db82ebcdf73fa24.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-adc128s052: Simplify using guard(mutex)

Error path in ADC reading function can be slighly simplified using the
guard(mutex).

Use guard(mutex) and document the mutex purpose.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/c4262cbf55748d505a74249d2bf46d7c3594d838.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-adc128s052: Use devm_mutex_init()

Quoting Jonathan:
"Whilst it doesn't bring huge advantage, now we have devm_mutex_init()
it seems reasonable to use it and maybe catch a use after free for the
lock"

Switch to use devm_mutex_init() while working on this file.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/efe4a039e2bfbf4dcf30743f6b7b88fce3b9ee39.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-adc128s052: Be consistent with arrays

The ti-adc128s052 driver has NULL terminated ID arrays for the
of_device_id, spi_device_id and acpi_device_id. All of these are
terminated by having an empty string as the last member of an array.
Only the of_device_id array uses the /* sentinel */ comment.

It's better to be consistent.

This /* sentinel */ comment serves no real purpose these days as people
are used to seeing these ID lists terminated with an empty array
element.

Drop the /* sentinel */ from the of_device_id.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/bb58002accc696bd4a8fbbab37100c6fa0c29941.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>