ssb: Fix indentation of comment

Shifted the closing */ to the next line
This is done to maintain code uniformity.

Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210428162907.bn5q3oh3sji6wlh4@kewl-virtual-machine

diff --git a/drivers/ssb/main.c b/drivers/ssb/main.c
index 0a26984..0e180c3 100644 (file)
--- a/drivers/ssb/main.c
+++ b/drivers/ssb/main.c
@@ -37,7 +37,8 @@ static LIST_HEAD(buses);
 /* Software ID counter */
 static unsigned int next_busnumber;
 /* buses_mutes locks the two buslists and the next_busnumber.
- * Don't lock this directly, but use ssb_buses_[un]lock() below. */
+ * Don't lock this directly, but use ssb_buses_[un]lock() below.
+ */
 static DEFINE_MUTEX(buses_mutex);
 
 /* There are differences in the codeflow, if the bus is
@@ -45,7 +46,8 @@ static DEFINE_MUTEX(buses_mutex);
  * are not available early. This is a mechanism to delay
  * these initializations to after early boot has finished.
  * It's also used to avoid mutex locking, as that's not
- * available and needed early. */
+ * available and needed early.
+ */
 static bool ssb_is_early_boot = 1;
 
 static void ssb_buses_lock(void);
@@ -161,7 +163,8 @@ int ssb_bus_resume(struct ssb_bus *bus)
        int err;
 
        /* Reset HW state information in memory, so that HW is
-        * completely reinitialized. */
+        * completely reinitialized.
+        */
        bus->mapped_device = NULL;
 #ifdef CONFIG_SSB_DRIVER_PCICORE
        bus->pcicore.setup_done = 0;
@@ -467,7 +470,8 @@ static int ssb_devices_register(struct ssb_bus *bus)
                sdev = &(bus->devices[i]);
 
                /* We don't register SSB-system devices to the kernel,
-                * as the drivers for them are built into SSB. */
+                * as the drivers for them are built into SSB.
+                */
                switch (sdev->id.coreid) {
                case SSB_DEV_CHIPCOMMON:
                case SSB_DEV_PCI:
@@ -521,7 +525,8 @@ static int ssb_devices_register(struct ssb_bus *bus)
                if (err) {
                        pr_err("Could not register %s\n", dev_name(dev));
                        /* Set dev to NULL to not unregister
-                        * dev on error unwinding. */
+                        * dev on error unwinding.
+                        */
                        sdev->dev = NULL;
                        put_device(dev);
                        goto error;
@@ -667,7 +672,8 @@ ssb_bus_register(struct ssb_bus *bus,
        ssb_bus_may_powerdown(bus);
 
        /* Queue it for attach.
-        * See the comment at the ssb_is_early_boot definition. */
+        * See the comment at the ssb_is_early_boot definition.
+        */
        list_add_tail(&bus->list, &attach_queue);
        if (!ssb_is_early_boot) {
                /* This is not early boot, so we must attach the bus now */
@@ -1007,7 +1013,8 @@ static void ssb_flush_tmslow(struct ssb_device *dev)
         * a machine check exception otherwise.
         * Do this by reading the register back to commit the
         * PCI write and delay an additional usec for the device
-        * to react to the change. */
+        * to react to the change.
+        */
        ssb_read32(dev, SSB_TMSLOW);
        udelay(1);
 }
@@ -1044,7 +1051,8 @@ void ssb_device_enable(struct ssb_device *dev, u32 core_specific_flags)
 EXPORT_SYMBOL(ssb_device_enable);
 
 /* Wait for bitmask in a register to get set or cleared.
- * timeout is in units of ten-microseconds */
+ * timeout is in units of ten-microseconds
+ */
 static int ssb_wait_bits(struct ssb_device *dev, u16 reg, u32 bitmask,
                         int timeout, int set)
 {
@@ -1153,7 +1161,8 @@ int ssb_bus_may_powerdown(struct ssb_bus *bus)
 
        /* On buses where more than one core may be working
         * at a time, we must not powerdown stuff if there are
-        * still cores that may want to run. */
+        * still cores that may want to run.
+        */
        if (bus->bustype == SSB_BUSTYPE_SSB)
                goto out;
 
@@ -1322,7 +1331,8 @@ out:
 }
 /* ssb must be initialized after PCI but before the ssb drivers.
  * That means we must use some initcall between subsys_initcall
- * and device_initcall. */
+ * and device_initcall.
+ */
 fs_initcall(ssb_modinit);
 
 static void __exit ssb_modexit(void)