+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * U300 clock implementation
- * Copyright (C) 2007-2012 ST-Ericsson AB
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- */
-#include <linux/clkdev.h>
-#include <linux/slab.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/clk-provider.h>
-#include <linux/spinlock.h>
-#include <linux/of.h>
-#include <linux/platform_data/clk-u300.h>
-
-/* APP side SYSCON registers */
-/* CLK Control Register 16bit (R/W) */
-#define U300_SYSCON_CCR (0x0000)
-#define U300_SYSCON_CCR_I2S1_USE_VCXO (0x0040)
-#define U300_SYSCON_CCR_I2S0_USE_VCXO (0x0020)
-#define U300_SYSCON_CCR_TURN_VCXO_ON (0x0008)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK (0x0007)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER (0x04)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW (0x03)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE (0x02)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH (0x01)
-#define U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST (0x00)
-/* CLK Status Register 16bit (R/W) */
-#define U300_SYSCON_CSR (0x0004)
-#define U300_SYSCON_CSR_PLL208_LOCK_IND (0x0002)
-#define U300_SYSCON_CSR_PLL13_LOCK_IND (0x0001)
-/* Reset lines for SLOW devices 16bit (R/W) */
-#define U300_SYSCON_RSR (0x0014)
-#define U300_SYSCON_RSR_PPM_RESET_EN (0x0200)
-#define U300_SYSCON_RSR_ACC_TMR_RESET_EN (0x0100)
-#define U300_SYSCON_RSR_APP_TMR_RESET_EN (0x0080)
-#define U300_SYSCON_RSR_RTC_RESET_EN (0x0040)
-#define U300_SYSCON_RSR_KEYPAD_RESET_EN (0x0020)
-#define U300_SYSCON_RSR_GPIO_RESET_EN (0x0010)
-#define U300_SYSCON_RSR_EH_RESET_EN (0x0008)
-#define U300_SYSCON_RSR_BTR_RESET_EN (0x0004)
-#define U300_SYSCON_RSR_UART_RESET_EN (0x0002)
-#define U300_SYSCON_RSR_SLOW_BRIDGE_RESET_EN (0x0001)
-/* Reset lines for FAST devices 16bit (R/W) */
-#define U300_SYSCON_RFR (0x0018)
-#define U300_SYSCON_RFR_UART1_RESET_ENABLE (0x0080)
-#define U300_SYSCON_RFR_SPI_RESET_ENABLE (0x0040)
-#define U300_SYSCON_RFR_MMC_RESET_ENABLE (0x0020)
-#define U300_SYSCON_RFR_PCM_I2S1_RESET_ENABLE (0x0010)
-#define U300_SYSCON_RFR_PCM_I2S0_RESET_ENABLE (0x0008)
-#define U300_SYSCON_RFR_I2C1_RESET_ENABLE (0x0004)
-#define U300_SYSCON_RFR_I2C0_RESET_ENABLE (0x0002)
-#define U300_SYSCON_RFR_FAST_BRIDGE_RESET_ENABLE (0x0001)
-/* Reset lines for the rest of the peripherals 16bit (R/W) */
-#define U300_SYSCON_RRR (0x001c)
-#define U300_SYSCON_RRR_CDS_RESET_EN (0x4000)
-#define U300_SYSCON_RRR_ISP_RESET_EN (0x2000)
-#define U300_SYSCON_RRR_INTCON_RESET_EN (0x1000)
-#define U300_SYSCON_RRR_MSPRO_RESET_EN (0x0800)
-#define U300_SYSCON_RRR_XGAM_RESET_EN (0x0100)
-#define U300_SYSCON_RRR_XGAM_VC_SYNC_RESET_EN (0x0080)
-#define U300_SYSCON_RRR_NANDIF_RESET_EN (0x0040)
-#define U300_SYSCON_RRR_EMIF_RESET_EN (0x0020)
-#define U300_SYSCON_RRR_DMAC_RESET_EN (0x0010)
-#define U300_SYSCON_RRR_CPU_RESET_EN (0x0008)
-#define U300_SYSCON_RRR_APEX_RESET_EN (0x0004)
-#define U300_SYSCON_RRR_AHB_RESET_EN (0x0002)
-#define U300_SYSCON_RRR_AAIF_RESET_EN (0x0001)
-/* Clock enable for SLOW peripherals 16bit (R/W) */
-#define U300_SYSCON_CESR (0x0020)
-#define U300_SYSCON_CESR_PPM_CLK_EN (0x0200)
-#define U300_SYSCON_CESR_ACC_TMR_CLK_EN (0x0100)
-#define U300_SYSCON_CESR_APP_TMR_CLK_EN (0x0080)
-#define U300_SYSCON_CESR_KEYPAD_CLK_EN (0x0040)
-#define U300_SYSCON_CESR_GPIO_CLK_EN (0x0010)
-#define U300_SYSCON_CESR_EH_CLK_EN (0x0008)
-#define U300_SYSCON_CESR_BTR_CLK_EN (0x0004)
-#define U300_SYSCON_CESR_UART_CLK_EN (0x0002)
-#define U300_SYSCON_CESR_SLOW_BRIDGE_CLK_EN (0x0001)
-/* Clock enable for FAST peripherals 16bit (R/W) */
-#define U300_SYSCON_CEFR (0x0024)
-#define U300_SYSCON_CEFR_UART1_CLK_EN (0x0200)
-#define U300_SYSCON_CEFR_I2S1_CORE_CLK_EN (0x0100)
-#define U300_SYSCON_CEFR_I2S0_CORE_CLK_EN (0x0080)
-#define U300_SYSCON_CEFR_SPI_CLK_EN (0x0040)
-#define U300_SYSCON_CEFR_MMC_CLK_EN (0x0020)
-#define U300_SYSCON_CEFR_I2S1_CLK_EN (0x0010)
-#define U300_SYSCON_CEFR_I2S0_CLK_EN (0x0008)
-#define U300_SYSCON_CEFR_I2C1_CLK_EN (0x0004)
-#define U300_SYSCON_CEFR_I2C0_CLK_EN (0x0002)
-#define U300_SYSCON_CEFR_FAST_BRIDGE_CLK_EN (0x0001)
-/* Clock enable for the rest of the peripherals 16bit (R/W) */
-#define U300_SYSCON_CERR (0x0028)
-#define U300_SYSCON_CERR_CDS_CLK_EN (0x2000)
-#define U300_SYSCON_CERR_ISP_CLK_EN (0x1000)
-#define U300_SYSCON_CERR_MSPRO_CLK_EN (0x0800)
-#define U300_SYSCON_CERR_AHB_SUBSYS_BRIDGE_CLK_EN (0x0400)
-#define U300_SYSCON_CERR_SEMI_CLK_EN (0x0200)
-#define U300_SYSCON_CERR_XGAM_CLK_EN (0x0100)
-#define U300_SYSCON_CERR_VIDEO_ENC_CLK_EN (0x0080)
-#define U300_SYSCON_CERR_NANDIF_CLK_EN (0x0040)
-#define U300_SYSCON_CERR_EMIF_CLK_EN (0x0020)
-#define U300_SYSCON_CERR_DMAC_CLK_EN (0x0010)
-#define U300_SYSCON_CERR_CPU_CLK_EN (0x0008)
-#define U300_SYSCON_CERR_APEX_CLK_EN (0x0004)
-#define U300_SYSCON_CERR_AHB_CLK_EN (0x0002)
-#define U300_SYSCON_CERR_AAIF_CLK_EN (0x0001)
-/* Single block clock enable 16bit (-/W) */
-#define U300_SYSCON_SBCER (0x002c)
-#define U300_SYSCON_SBCER_PPM_CLK_EN (0x0009)
-#define U300_SYSCON_SBCER_ACC_TMR_CLK_EN (0x0008)
-#define U300_SYSCON_SBCER_APP_TMR_CLK_EN (0x0007)
-#define U300_SYSCON_SBCER_KEYPAD_CLK_EN (0x0006)
-#define U300_SYSCON_SBCER_GPIO_CLK_EN (0x0004)
-#define U300_SYSCON_SBCER_EH_CLK_EN (0x0003)
-#define U300_SYSCON_SBCER_BTR_CLK_EN (0x0002)
-#define U300_SYSCON_SBCER_UART_CLK_EN (0x0001)
-#define U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN (0x0000)
-#define U300_SYSCON_SBCER_UART1_CLK_EN (0x0019)
-#define U300_SYSCON_SBCER_I2S1_CORE_CLK_EN (0x0018)
-#define U300_SYSCON_SBCER_I2S0_CORE_CLK_EN (0x0017)
-#define U300_SYSCON_SBCER_SPI_CLK_EN (0x0016)
-#define U300_SYSCON_SBCER_MMC_CLK_EN (0x0015)
-#define U300_SYSCON_SBCER_I2S1_CLK_EN (0x0014)
-#define U300_SYSCON_SBCER_I2S0_CLK_EN (0x0013)
-#define U300_SYSCON_SBCER_I2C1_CLK_EN (0x0012)
-#define U300_SYSCON_SBCER_I2C0_CLK_EN (0x0011)
-#define U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN (0x0010)
-#define U300_SYSCON_SBCER_CDS_CLK_EN (0x002D)
-#define U300_SYSCON_SBCER_ISP_CLK_EN (0x002C)
-#define U300_SYSCON_SBCER_MSPRO_CLK_EN (0x002B)
-#define U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN (0x002A)
-#define U300_SYSCON_SBCER_SEMI_CLK_EN (0x0029)
-#define U300_SYSCON_SBCER_XGAM_CLK_EN (0x0028)
-#define U300_SYSCON_SBCER_VIDEO_ENC_CLK_EN (0x0027)
-#define U300_SYSCON_SBCER_NANDIF_CLK_EN (0x0026)
-#define U300_SYSCON_SBCER_EMIF_CLK_EN (0x0025)
-#define U300_SYSCON_SBCER_DMAC_CLK_EN (0x0024)
-#define U300_SYSCON_SBCER_CPU_CLK_EN (0x0023)
-#define U300_SYSCON_SBCER_APEX_CLK_EN (0x0022)
-#define U300_SYSCON_SBCER_AHB_CLK_EN (0x0021)
-#define U300_SYSCON_SBCER_AAIF_CLK_EN (0x0020)
-/* Single block clock disable 16bit (-/W) */
-#define U300_SYSCON_SBCDR (0x0030)
-/* Same values as above for SBCER */
-/* Clock force SLOW peripherals 16bit (R/W) */
-#define U300_SYSCON_CFSR (0x003c)
-#define U300_SYSCON_CFSR_PPM_CLK_FORCE_EN (0x0200)
-#define U300_SYSCON_CFSR_ACC_TMR_CLK_FORCE_EN (0x0100)
-#define U300_SYSCON_CFSR_APP_TMR_CLK_FORCE_EN (0x0080)
-#define U300_SYSCON_CFSR_KEYPAD_CLK_FORCE_EN (0x0020)
-#define U300_SYSCON_CFSR_GPIO_CLK_FORCE_EN (0x0010)
-#define U300_SYSCON_CFSR_EH_CLK_FORCE_EN (0x0008)
-#define U300_SYSCON_CFSR_BTR_CLK_FORCE_EN (0x0004)
-#define U300_SYSCON_CFSR_UART_CLK_FORCE_EN (0x0002)
-#define U300_SYSCON_CFSR_SLOW_BRIDGE_CLK_FORCE_EN (0x0001)
-/* Clock force FAST peripherals 16bit (R/W) */
-#define U300_SYSCON_CFFR (0x40)
-/* Values not defined. Define if you want to use them. */
-/* Clock force the rest of the peripherals 16bit (R/W) */
-#define U300_SYSCON_CFRR (0x44)
-#define U300_SYSCON_CFRR_CDS_CLK_FORCE_EN (0x2000)
-#define U300_SYSCON_CFRR_ISP_CLK_FORCE_EN (0x1000)
-#define U300_SYSCON_CFRR_MSPRO_CLK_FORCE_EN (0x0800)
-#define U300_SYSCON_CFRR_AHB_SUBSYS_BRIDGE_CLK_FORCE_EN (0x0400)
-#define U300_SYSCON_CFRR_SEMI_CLK_FORCE_EN (0x0200)
-#define U300_SYSCON_CFRR_XGAM_CLK_FORCE_EN (0x0100)
-#define U300_SYSCON_CFRR_VIDEO_ENC_CLK_FORCE_EN (0x0080)
-#define U300_SYSCON_CFRR_NANDIF_CLK_FORCE_EN (0x0040)
-#define U300_SYSCON_CFRR_EMIF_CLK_FORCE_EN (0x0020)
-#define U300_SYSCON_CFRR_DMAC_CLK_FORCE_EN (0x0010)
-#define U300_SYSCON_CFRR_CPU_CLK_FORCE_EN (0x0008)
-#define U300_SYSCON_CFRR_APEX_CLK_FORCE_EN (0x0004)
-#define U300_SYSCON_CFRR_AHB_CLK_FORCE_EN (0x0002)
-#define U300_SYSCON_CFRR_AAIF_CLK_FORCE_EN (0x0001)
-/* PLL208 Frequency Control 16bit (R/W) */
-#define U300_SYSCON_PFCR (0x48)
-#define U300_SYSCON_PFCR_DPLL_MULT_NUM (0x000F)
-/* Power Management Control 16bit (R/W) */
-#define U300_SYSCON_PMCR (0x50)
-#define U300_SYSCON_PMCR_DCON_ENABLE (0x0002)
-#define U300_SYSCON_PMCR_PWR_MGNT_ENABLE (0x0001)
-/* Reset Out 16bit (R/W) */
-#define U300_SYSCON_RCR (0x6c)
-#define U300_SYSCON_RCR_RESOUT0_RST_N_DISABLE (0x0001)
-/* EMIF Slew Rate Control 16bit (R/W) */
-#define U300_SYSCON_SRCLR (0x70)
-#define U300_SYSCON_SRCLR_MASK (0x03FF)
-#define U300_SYSCON_SRCLR_VALUE (0x03FF)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_B (0x0200)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_A (0x0100)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_B (0x0080)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_A (0x0040)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_B (0x0020)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_A (0x0010)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_B (0x0008)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_A (0x0004)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_B (0x0002)
-#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_A (0x0001)
-/* EMIF Clock Control Register 16bit (R/W) */
-#define U300_SYSCON_ECCR (0x0078)
-#define U300_SYSCON_ECCR_MASK (0x000F)
-#define U300_SYSCON_ECCR_EMIF_1_STATIC_CLK_EN_N_DISABLE (0x0008)
-#define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE (0x0004)
-#define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE (0x0002)
-#define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE (0x0001)
-/* MMC/MSPRO frequency divider register 0 16bit (R/W) */
-#define U300_SYSCON_MMF0R (0x90)
-#define U300_SYSCON_MMF0R_MASK (0x00FF)
-#define U300_SYSCON_MMF0R_FREQ_0_HIGH_MASK (0x00F0)
-#define U300_SYSCON_MMF0R_FREQ_0_LOW_MASK (0x000F)
-/* MMC/MSPRO frequency divider register 1 16bit (R/W) */
-#define U300_SYSCON_MMF1R (0x94)
-#define U300_SYSCON_MMF1R_MASK (0x00FF)
-#define U300_SYSCON_MMF1R_FREQ_1_HIGH_MASK (0x00F0)
-#define U300_SYSCON_MMF1R_FREQ_1_LOW_MASK (0x000F)
-/* Clock control for the MMC and MSPRO blocks 16bit (R/W) */
-#define U300_SYSCON_MMCR (0x9C)
-#define U300_SYSCON_MMCR_MASK (0x0003)
-#define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE (0x0002)
-#define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE (0x0001)
-/* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */
-#define U300_SYSCON_S0CCR (0x120)
-#define U300_SYSCON_S0CCR_FIELD_MASK (0x43FF)
-#define U300_SYSCON_S0CCR_CLOCK_REQ (0x4000)
-#define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR (0x2000)
-#define U300_SYSCON_S0CCR_CLOCK_INV (0x0200)
-#define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK (0x01E0)
-#define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK (0x001E)
-#define U300_SYSCON_S0CCR_CLOCK_ENABLE (0x0001)
-#define U300_SYSCON_S0CCR_SEL_MCLK (0x8 << 1)
-#define U300_SYSCON_S0CCR_SEL_ACC_FSM_CLK (0xA << 1)
-#define U300_SYSCON_S0CCR_SEL_PLL60_48_CLK (0xC << 1)
-#define U300_SYSCON_S0CCR_SEL_PLL60_60_CLK (0xD << 1)
-#define U300_SYSCON_S0CCR_SEL_ACC_PLL208_CLK (0xE << 1)
-#define U300_SYSCON_S0CCR_SEL_APP_PLL13_CLK (0x0 << 1)
-#define U300_SYSCON_S0CCR_SEL_APP_FSM_CLK (0x2 << 1)
-#define U300_SYSCON_S0CCR_SEL_RTC_CLK (0x4 << 1)
-#define U300_SYSCON_S0CCR_SEL_APP_PLL208_CLK (0x6 << 1)
-/* SYS_1_CLK_CONTROL second clock control 16 bit (R/W) */
-#define U300_SYSCON_S1CCR (0x124)
-#define U300_SYSCON_S1CCR_FIELD_MASK (0x43FF)
-#define U300_SYSCON_S1CCR_CLOCK_REQ (0x4000)
-#define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR (0x2000)
-#define U300_SYSCON_S1CCR_CLOCK_INV (0x0200)
-#define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK (0x01E0)
-#define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK (0x001E)
-#define U300_SYSCON_S1CCR_CLOCK_ENABLE (0x0001)
-#define U300_SYSCON_S1CCR_SEL_MCLK (0x8 << 1)
-#define U300_SYSCON_S1CCR_SEL_ACC_FSM_CLK (0xA << 1)
-#define U300_SYSCON_S1CCR_SEL_PLL60_48_CLK (0xC << 1)
-#define U300_SYSCON_S1CCR_SEL_PLL60_60_CLK (0xD << 1)
-#define U300_SYSCON_S1CCR_SEL_ACC_PLL208_CLK (0xE << 1)
-#define U300_SYSCON_S1CCR_SEL_ACC_PLL13_CLK (0x0 << 1)
-#define U300_SYSCON_S1CCR_SEL_APP_FSM_CLK (0x2 << 1)
-#define U300_SYSCON_S1CCR_SEL_RTC_CLK (0x4 << 1)
-#define U300_SYSCON_S1CCR_SEL_APP_PLL208_CLK (0x6 << 1)
-/* SYS_2_CLK_CONTROL third clock control 16 bit (R/W) */
-#define U300_SYSCON_S2CCR (0x128)
-#define U300_SYSCON_S2CCR_FIELD_MASK (0xC3FF)
-#define U300_SYSCON_S2CCR_CLK_STEAL (0x8000)
-#define U300_SYSCON_S2CCR_CLOCK_REQ (0x4000)
-#define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR (0x2000)
-#define U300_SYSCON_S2CCR_CLOCK_INV (0x0200)
-#define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK (0x01E0)
-#define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK (0x001E)
-#define U300_SYSCON_S2CCR_CLOCK_ENABLE (0x0001)
-#define U300_SYSCON_S2CCR_SEL_MCLK (0x8 << 1)
-#define U300_SYSCON_S2CCR_SEL_ACC_FSM_CLK (0xA << 1)
-#define U300_SYSCON_S2CCR_SEL_PLL60_48_CLK (0xC << 1)
-#define U300_SYSCON_S2CCR_SEL_PLL60_60_CLK (0xD << 1)
-#define U300_SYSCON_S2CCR_SEL_ACC_PLL208_CLK (0xE << 1)
-#define U300_SYSCON_S2CCR_SEL_ACC_PLL13_CLK (0x0 << 1)
-#define U300_SYSCON_S2CCR_SEL_APP_FSM_CLK (0x2 << 1)
-#define U300_SYSCON_S2CCR_SEL_RTC_CLK (0x4 << 1)
-#define U300_SYSCON_S2CCR_SEL_APP_PLL208_CLK (0x6 << 1)
-/* SC_PLL_IRQ_CONTROL 16bit (R/W) */
-#define U300_SYSCON_PICR (0x0130)
-#define U300_SYSCON_PICR_MASK (0x00FF)
-#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE (0x0080)
-#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE (0x0040)
-#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE (0x0020)
-#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE (0x0010)
-#define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE (0x0008)
-#define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE (0x0004)
-#define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE (0x0002)
-#define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE (0x0001)
-/* SC_PLL_IRQ_STATUS 16 bit (R/-) */
-#define U300_SYSCON_PISR (0x0134)
-#define U300_SYSCON_PISR_MASK (0x000F)
-#define U300_SYSCON_PISR_PLL13_UNLOCK_IND (0x0008)
-#define U300_SYSCON_PISR_PLL13_LOCK_IND (0x0004)
-#define U300_SYSCON_PISR_PLL208_UNLOCK_IND (0x0002)
-#define U300_SYSCON_PISR_PLL208_LOCK_IND (0x0001)
-/* SC_PLL_IRQ_CLEAR 16 bit (-/W) */
-#define U300_SYSCON_PICLR (0x0138)
-#define U300_SYSCON_PICLR_MASK (0x000F)
-#define U300_SYSCON_PICLR_RWMASK (0x0000)
-#define U300_SYSCON_PICLR_PLL13_UNLOCK_SC (0x0008)
-#define U300_SYSCON_PICLR_PLL13_LOCK_SC (0x0004)
-#define U300_SYSCON_PICLR_PLL208_UNLOCK_SC (0x0002)
-#define U300_SYSCON_PICLR_PLL208_LOCK_SC (0x0001)
-/* Clock activity observability register 0 */
-#define U300_SYSCON_C0OAR (0x140)
-#define U300_SYSCON_C0OAR_MASK (0xFFFF)
-#define U300_SYSCON_C0OAR_VALUE (0xFFFF)
-#define U300_SYSCON_C0OAR_BT_H_CLK (0x8000)
-#define U300_SYSCON_C0OAR_ASPB_P_CLK (0x4000)
-#define U300_SYSCON_C0OAR_APP_SEMI_H_CLK (0x2000)
-#define U300_SYSCON_C0OAR_APP_SEMI_CLK (0x1000)
-#define U300_SYSCON_C0OAR_APP_MMC_MSPRO_CLK (0x0800)
-#define U300_SYSCON_C0OAR_APP_I2S1_CLK (0x0400)
-#define U300_SYSCON_C0OAR_APP_I2S0_CLK (0x0200)
-#define U300_SYSCON_C0OAR_APP_CPU_CLK (0x0100)
-#define U300_SYSCON_C0OAR_APP_52_CLK (0x0080)
-#define U300_SYSCON_C0OAR_APP_208_CLK (0x0040)
-#define U300_SYSCON_C0OAR_APP_104_CLK (0x0020)
-#define U300_SYSCON_C0OAR_APEX_CLK (0x0010)
-#define U300_SYSCON_C0OAR_AHPB_M_H_CLK (0x0008)
-#define U300_SYSCON_C0OAR_AHB_CLK (0x0004)
-#define U300_SYSCON_C0OAR_AFPB_P_CLK (0x0002)
-#define U300_SYSCON_C0OAR_AAIF_CLK (0x0001)
-/* Clock activity observability register 1 */
-#define U300_SYSCON_C1OAR (0x144)
-#define U300_SYSCON_C1OAR_MASK (0x3FFE)
-#define U300_SYSCON_C1OAR_VALUE (0x3FFE)
-#define U300_SYSCON_C1OAR_NFIF_F_CLK (0x2000)
-#define U300_SYSCON_C1OAR_MSPRO_CLK (0x1000)
-#define U300_SYSCON_C1OAR_MMC_P_CLK (0x0800)
-#define U300_SYSCON_C1OAR_MMC_CLK (0x0400)
-#define U300_SYSCON_C1OAR_KP_P_CLK (0x0200)
-#define U300_SYSCON_C1OAR_I2C1_P_CLK (0x0100)
-#define U300_SYSCON_C1OAR_I2C0_P_CLK (0x0080)
-#define U300_SYSCON_C1OAR_GPIO_CLK (0x0040)
-#define U300_SYSCON_C1OAR_EMIF_MPMC_CLK (0x0020)
-#define U300_SYSCON_C1OAR_EMIF_H_CLK (0x0010)
-#define U300_SYSCON_C1OAR_EVHIST_CLK (0x0008)
-#define U300_SYSCON_C1OAR_PPM_CLK (0x0004)
-#define U300_SYSCON_C1OAR_DMA_CLK (0x0002)
-/* Clock activity observability register 2 */
-#define U300_SYSCON_C2OAR (0x148)
-#define U300_SYSCON_C2OAR_MASK (0x0FFF)
-#define U300_SYSCON_C2OAR_VALUE (0x0FFF)
-#define U300_SYSCON_C2OAR_XGAM_CDI_CLK (0x0800)
-#define U300_SYSCON_C2OAR_XGAM_CLK (0x0400)
-#define U300_SYSCON_C2OAR_VC_H_CLK (0x0200)
-#define U300_SYSCON_C2OAR_VC_CLK (0x0100)
-#define U300_SYSCON_C2OAR_UA_P_CLK (0x0080)
-#define U300_SYSCON_C2OAR_TMR1_CLK (0x0040)
-#define U300_SYSCON_C2OAR_TMR0_CLK (0x0020)
-#define U300_SYSCON_C2OAR_SPI_P_CLK (0x0010)
-#define U300_SYSCON_C2OAR_PCM_I2S1_CORE_CLK (0x0008)
-#define U300_SYSCON_C2OAR_PCM_I2S1_CLK (0x0004)
-#define U300_SYSCON_C2OAR_PCM_I2S0_CORE_CLK (0x0002)
-#define U300_SYSCON_C2OAR_PCM_I2S0_CLK (0x0001)
-
-
-/*
- * The clocking hierarchy currently looks like this.
- * NOTE: the idea is NOT to show how the clocks are routed on the chip!
- * The ideas is to show dependencies, so a clock higher up in the
- * hierarchy has to be on in order for another clock to be on. Now,
- * both CPU and DMA can actually be on top of the hierarchy, and that
- * is not modeled currently. Instead we have the backbone AMBA bus on
- * top. This bus cannot be programmed in any way but conceptually it
- * needs to be active for the bridges and devices to transport data.
- *
- * Please be aware that a few clocks are hw controlled, which mean that
- * the hw itself can turn on/off or change the rate of the clock when
- * needed!
- *
- * AMBA bus
- * |
- * +- CPU
- * +- FSMC NANDIF NAND Flash interface
- * +- SEMI Shared Memory interface
- * +- ISP Image Signal Processor (U335 only)
- * +- CDS (U335 only)
- * +- DMA Direct Memory Access Controller
- * +- AAIF APP/ACC Interface (Mobile Scalable Link, MSL)
- * +- APEX
- * +- VIDEO_ENC AVE2/3 Video Encoder
- * +- XGAM Graphics Accelerator Controller
- * +- AHB
- * |
- * +- ahb:0 AHB Bridge
- * | |
- * | +- ahb:1 INTCON Interrupt controller
- * | +- ahb:3 MSPRO Memory Stick Pro controller
- * | +- ahb:4 EMIF External Memory interface
- * |
- * +- fast:0 FAST bridge
- * | |
- * | +- fast:1 MMCSD MMC/SD card reader controller
- * | +- fast:2 I2S0 PCM I2S channel 0 controller
- * | +- fast:3 I2S1 PCM I2S channel 1 controller
- * | +- fast:4 I2C0 I2C channel 0 controller
- * | +- fast:5 I2C1 I2C channel 1 controller
- * | +- fast:6 SPI SPI controller
- * | +- fast:7 UART1 Secondary UART (U335 only)
- * |
- * +- slow:0 SLOW bridge
- * |
- * +- slow:1 SYSCON (not possible to control)
- * +- slow:2 WDOG Watchdog
- * +- slow:3 UART0 primary UART
- * +- slow:4 TIMER_APP Application timer - used in Linux
- * +- slow:5 KEYPAD controller
- * +- slow:6 GPIO controller
- * +- slow:7 RTC controller
- * +- slow:8 BT Bus Tracer (not used currently)
- * +- slow:9 EH Event Handler (not used currently)
- * +- slow:a TIMER_ACC Access style timer (not used currently)
- * +- slow:b PPM (U335 only, what is that?)
- */
-
-/* Global syscon virtual base */
-static void __iomem *syscon_vbase;
-
-/**
- * struct clk_syscon - U300 syscon clock
- * @hw: corresponding clock hardware entry
- * @hw_ctrld: whether this clock is hardware controlled (for refcount etc)
- * and does not need any magic pokes to be enabled/disabled
- * @reset: state holder, whether this block's reset line is asserted or not
- * @res_reg: reset line enable/disable flag register
- * @res_bit: bit for resetting or taking this consumer out of reset
- * @en_reg: clock line enable/disable flag register
- * @en_bit: bit for enabling/disabling this consumer clock line
- * @clk_val: magic value to poke in the register to enable/disable
- * this one clock
- */
-struct clk_syscon {
- struct clk_hw hw;
- bool hw_ctrld;
- bool reset;
- void __iomem *res_reg;
- u8 res_bit;
- void __iomem *en_reg;
- u8 en_bit;
- u16 clk_val;
-};
-
-#define to_syscon(_hw) container_of(_hw, struct clk_syscon, hw)
-
-static DEFINE_SPINLOCK(syscon_resetreg_lock);
-
-/*
- * Reset control functions. We remember if a block has been
- * taken out of reset and don't remove the reset assertion again
- * and vice versa. Currently we only remove resets so the
- * enablement function is defined out.
- */
-static void syscon_block_reset_enable(struct clk_syscon *sclk)
-{
- unsigned long iflags;
- u16 val;
-
- /* Not all blocks support resetting */
- if (!sclk->res_reg)
- return;
- spin_lock_irqsave(&syscon_resetreg_lock, iflags);
- val = readw(sclk->res_reg);
- val |= BIT(sclk->res_bit);
- writew(val, sclk->res_reg);
- spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
- sclk->reset = true;
-}
-
-static void syscon_block_reset_disable(struct clk_syscon *sclk)
-{
- unsigned long iflags;
- u16 val;
-
- /* Not all blocks support resetting */
- if (!sclk->res_reg)
- return;
- spin_lock_irqsave(&syscon_resetreg_lock, iflags);
- val = readw(sclk->res_reg);
- val &= ~BIT(sclk->res_bit);
- writew(val, sclk->res_reg);
- spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
- sclk->reset = false;
-}
-
-static int syscon_clk_prepare(struct clk_hw *hw)
-{
- struct clk_syscon *sclk = to_syscon(hw);
-
- /* If the block is in reset, bring it out */
- if (sclk->reset)
- syscon_block_reset_disable(sclk);
- return 0;
-}
-
-static void syscon_clk_unprepare(struct clk_hw *hw)
-{
- struct clk_syscon *sclk = to_syscon(hw);
-
- /* Please don't force the console into reset */
- if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
- return;
- /* When unpreparing, force block into reset */
- if (!sclk->reset)
- syscon_block_reset_enable(sclk);
-}
-
-static int syscon_clk_enable(struct clk_hw *hw)
-{
- struct clk_syscon *sclk = to_syscon(hw);
-
- /* Don't touch the hardware controlled clocks */
- if (sclk->hw_ctrld)
- return 0;
- /* These cannot be controlled */
- if (sclk->clk_val == 0xFFFFU)
- return 0;
-
- writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCER);
- return 0;
-}
-
-static void syscon_clk_disable(struct clk_hw *hw)
-{
- struct clk_syscon *sclk = to_syscon(hw);
-
- /* Don't touch the hardware controlled clocks */
- if (sclk->hw_ctrld)
- return;
- if (sclk->clk_val == 0xFFFFU)
- return;
- /* Please don't disable the console port */
- if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
- return;
-
- writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCDR);
-}
-
-static int syscon_clk_is_enabled(struct clk_hw *hw)
-{
- struct clk_syscon *sclk = to_syscon(hw);
- u16 val;
-
- /* If no enable register defined, it's always-on */
- if (!sclk->en_reg)
- return 1;
-
- val = readw(sclk->en_reg);
- val &= BIT(sclk->en_bit);
-
- return val ? 1 : 0;
-}
-
-static u16 syscon_get_perf(void)
-{
- u16 val;
-
- val = readw(syscon_vbase + U300_SYSCON_CCR);
- val &= U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
- return val;
-}
-
-static unsigned long
-syscon_clk_recalc_rate(struct clk_hw *hw,
- unsigned long parent_rate)
-{
- struct clk_syscon *sclk = to_syscon(hw);
- u16 perf = syscon_get_perf();
-
- switch (sclk->clk_val) {
- case U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN:
- case U300_SYSCON_SBCER_I2C0_CLK_EN:
- case U300_SYSCON_SBCER_I2C1_CLK_EN:
- case U300_SYSCON_SBCER_MMC_CLK_EN:
- case U300_SYSCON_SBCER_SPI_CLK_EN:
- /* The FAST clocks have one progression */
- switch (perf) {
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
- return 13000000;
- default:
- return parent_rate; /* 26 MHz */
- }
- case U300_SYSCON_SBCER_DMAC_CLK_EN:
- case U300_SYSCON_SBCER_NANDIF_CLK_EN:
- case U300_SYSCON_SBCER_XGAM_CLK_EN:
- /* AMBA interconnect peripherals */
- switch (perf) {
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
- return 6500000;
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
- return 26000000;
- default:
- return parent_rate; /* 52 MHz */
- }
- case U300_SYSCON_SBCER_SEMI_CLK_EN:
- case U300_SYSCON_SBCER_EMIF_CLK_EN:
- /* EMIF speeds */
- switch (perf) {
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
- return 13000000;
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
- return 52000000;
- default:
- return 104000000;
- }
- case U300_SYSCON_SBCER_CPU_CLK_EN:
- /* And the fast CPU clock */
- switch (perf) {
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
- return 13000000;
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
- return 52000000;
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
- return 104000000;
- default:
- return parent_rate; /* 208 MHz */
- }
- default:
- /*
- * The SLOW clocks and default just inherit the rate of
- * their parent (typically PLL13 13 MHz).
- */
- return parent_rate;
- }
-}
-
-static long
-syscon_clk_round_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long *prate)
-{
- struct clk_syscon *sclk = to_syscon(hw);
-
- if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
- return *prate;
- /* We really only support setting the rate of the CPU clock */
- if (rate <= 13000000)
- return 13000000;
- if (rate <= 52000000)
- return 52000000;
- if (rate <= 104000000)
- return 104000000;
- return 208000000;
-}
-
-static int syscon_clk_set_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long parent_rate)
-{
- struct clk_syscon *sclk = to_syscon(hw);
- u16 val;
-
- /* We only support setting the rate of the CPU clock */
- if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
- return -EINVAL;
- switch (rate) {
- case 13000000:
- val = U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER;
- break;
- case 52000000:
- val = U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE;
- break;
- case 104000000:
- val = U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH;
- break;
- case 208000000:
- val = U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST;
- break;
- default:
- return -EINVAL;
- }
- val |= readw(syscon_vbase + U300_SYSCON_CCR) &
- ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK ;
- writew(val, syscon_vbase + U300_SYSCON_CCR);
- return 0;
-}
-
-static const struct clk_ops syscon_clk_ops = {
- .prepare = syscon_clk_prepare,
- .unprepare = syscon_clk_unprepare,
- .enable = syscon_clk_enable,
- .disable = syscon_clk_disable,
- .is_enabled = syscon_clk_is_enabled,
- .recalc_rate = syscon_clk_recalc_rate,
- .round_rate = syscon_clk_round_rate,
- .set_rate = syscon_clk_set_rate,
-};
-
-static struct clk_hw * __init
-syscon_clk_register(struct device *dev, const char *name,
- const char *parent_name, unsigned long flags,
- bool hw_ctrld,
- void __iomem *res_reg, u8 res_bit,
- void __iomem *en_reg, u8 en_bit,
- u16 clk_val)
-{
- struct clk_hw *hw;
- struct clk_syscon *sclk;
- struct clk_init_data init;
- int ret;
-
- sclk = kzalloc(sizeof(*sclk), GFP_KERNEL);
- if (!sclk)
- return ERR_PTR(-ENOMEM);
-
- init.name = name;
- init.ops = &syscon_clk_ops;
- init.flags = flags;
- init.parent_names = (parent_name ? &parent_name : NULL);
- init.num_parents = (parent_name ? 1 : 0);
- sclk->hw.init = &init;
- sclk->hw_ctrld = hw_ctrld;
- /* Assume the block is in reset at registration */
- sclk->reset = true;
- sclk->res_reg = res_reg;
- sclk->res_bit = res_bit;
- sclk->en_reg = en_reg;
- sclk->en_bit = en_bit;
- sclk->clk_val = clk_val;
-
- hw = &sclk->hw;
- ret = clk_hw_register(dev, hw);
- if (ret) {
- kfree(sclk);
- hw = ERR_PTR(ret);
- }
-
- return hw;
-}
-
-#define U300_CLK_TYPE_SLOW 0
-#define U300_CLK_TYPE_FAST 1
-#define U300_CLK_TYPE_REST 2
-
-/**
- * struct u300_clock - defines the bits and pieces for a certain clock
- * @type: the clock type, slow fast or rest
- * @id: the bit in the slow/fast/rest register for this clock
- * @hw_ctrld: whether the clock is hardware controlled
- * @clk_val: a value to poke in the one-write enable/disable registers
- */
-struct u300_clock {
- u8 type;
- u8 id;
- bool hw_ctrld;
- u16 clk_val;
-};
-
-static struct u300_clock const u300_clk_lookup[] __initconst = {
- {
- .type = U300_CLK_TYPE_REST,
- .id = 3,
- .hw_ctrld = true,
- .clk_val = U300_SYSCON_SBCER_CPU_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_REST,
- .id = 4,
- .hw_ctrld = true,
- .clk_val = U300_SYSCON_SBCER_DMAC_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_REST,
- .id = 5,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_EMIF_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_REST,
- .id = 6,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_NANDIF_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_REST,
- .id = 8,
- .hw_ctrld = true,
- .clk_val = U300_SYSCON_SBCER_XGAM_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_REST,
- .id = 9,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_SEMI_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_REST,
- .id = 10,
- .hw_ctrld = true,
- .clk_val = U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_REST,
- .id = 12,
- .hw_ctrld = false,
- /* INTCON: cannot be enabled, just taken out of reset */
- .clk_val = 0xFFFFU,
- },
- {
- .type = U300_CLK_TYPE_FAST,
- .id = 0,
- .hw_ctrld = true,
- .clk_val = U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_FAST,
- .id = 1,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_I2C0_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_FAST,
- .id = 2,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_I2C1_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_FAST,
- .id = 5,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_MMC_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_FAST,
- .id = 6,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_SPI_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_SLOW,
- .id = 0,
- .hw_ctrld = true,
- .clk_val = U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_SLOW,
- .id = 1,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_UART_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_SLOW,
- .id = 4,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_GPIO_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_SLOW,
- .id = 6,
- .hw_ctrld = true,
- /* No clock enable register bit */
- .clk_val = 0xFFFFU,
- },
- {
- .type = U300_CLK_TYPE_SLOW,
- .id = 7,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_APP_TMR_CLK_EN,
- },
- {
- .type = U300_CLK_TYPE_SLOW,
- .id = 8,
- .hw_ctrld = false,
- .clk_val = U300_SYSCON_SBCER_ACC_TMR_CLK_EN,
- },
-};
-
-static void __init of_u300_syscon_clk_init(struct device_node *np)
-{
- struct clk_hw *hw = ERR_PTR(-EINVAL);
- const char *clk_name = np->name;
- const char *parent_name;
- void __iomem *res_reg;
- void __iomem *en_reg;
- u32 clk_type;
- u32 clk_id;
- int i;
-
- if (of_property_read_u32(np, "clock-type", &clk_type)) {
- pr_err("%s: syscon clock \"%s\" missing clock-type property\n",
- __func__, clk_name);
- return;
- }
- if (of_property_read_u32(np, "clock-id", &clk_id)) {
- pr_err("%s: syscon clock \"%s\" missing clock-id property\n",
- __func__, clk_name);
- return;
- }
- parent_name = of_clk_get_parent_name(np, 0);
-
- switch (clk_type) {
- case U300_CLK_TYPE_SLOW:
- res_reg = syscon_vbase + U300_SYSCON_RSR;
- en_reg = syscon_vbase + U300_SYSCON_CESR;
- break;
- case U300_CLK_TYPE_FAST:
- res_reg = syscon_vbase + U300_SYSCON_RFR;
- en_reg = syscon_vbase + U300_SYSCON_CEFR;
- break;
- case U300_CLK_TYPE_REST:
- res_reg = syscon_vbase + U300_SYSCON_RRR;
- en_reg = syscon_vbase + U300_SYSCON_CERR;
- break;
- default:
- pr_err("unknown clock type %x specified\n", clk_type);
- return;
- }
-
- for (i = 0; i < ARRAY_SIZE(u300_clk_lookup); i++) {
- const struct u300_clock *u3clk = &u300_clk_lookup[i];
-
- if (u3clk->type == clk_type && u3clk->id == clk_id)
- hw = syscon_clk_register(NULL, clk_name, parent_name,
- 0, u3clk->hw_ctrld,
- res_reg, u3clk->id,
- en_reg, u3clk->id,
- u3clk->clk_val);
- }
-
- if (!IS_ERR(hw)) {
- of_clk_add_hw_provider(np, of_clk_hw_simple_get, hw);
-
- /*
- * Some few system clocks - device tree does not
- * represent clocks without a corresponding device node.
- * for now we add these three clocks here.
- */
- if (clk_type == U300_CLK_TYPE_REST && clk_id == 5)
- clk_hw_register_clkdev(hw, NULL, "pl172");
- if (clk_type == U300_CLK_TYPE_REST && clk_id == 9)
- clk_hw_register_clkdev(hw, NULL, "semi");
- if (clk_type == U300_CLK_TYPE_REST && clk_id == 12)
- clk_hw_register_clkdev(hw, NULL, "intcon");
- }
-}
-
-/**
- * struct clk_mclk - U300 MCLK clock (MMC/SD clock)
- * @hw: corresponding clock hardware entry
- * @is_mspro: if this is the memory stick clock rather than MMC/SD
- */
-struct clk_mclk {
- struct clk_hw hw;
- bool is_mspro;
-};
-
-#define to_mclk(_hw) container_of(_hw, struct clk_mclk, hw)
-
-static int mclk_clk_prepare(struct clk_hw *hw)
-{
- struct clk_mclk *mclk = to_mclk(hw);
- u16 val;
-
- /* The MMC and MSPRO clocks need some special set-up */
- if (!mclk->is_mspro) {
- /* Set default MMC clock divisor to 18.9 MHz */
- writew(0x0054U, syscon_vbase + U300_SYSCON_MMF0R);
- val = readw(syscon_vbase + U300_SYSCON_MMCR);
- /* Disable the MMC feedback clock */
- val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
- /* Disable MSPRO frequency */
- val &= ~U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
- writew(val, syscon_vbase + U300_SYSCON_MMCR);
- } else {
- val = readw(syscon_vbase + U300_SYSCON_MMCR);
- /* Disable the MMC feedback clock */
- val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
- /* Enable MSPRO frequency */
- val |= U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
- writew(val, syscon_vbase + U300_SYSCON_MMCR);
- }
-
- return 0;
-}
-
-static unsigned long
-mclk_clk_recalc_rate(struct clk_hw *hw,
- unsigned long parent_rate)
-{
- u16 perf = syscon_get_perf();
-
- switch (perf) {
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
- /*
- * Here, the 208 MHz PLL gets shut down and the always
- * on 13 MHz PLL used for RTC etc kicks into use
- * instead.
- */
- return 13000000;
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
- case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST:
- {
- /*
- * This clock is under program control. The register is
- * divided in two nybbles, bit 7-4 gives cycles-1 to count
- * high, bit 3-0 gives cycles-1 to count low. Distribute
- * these with no more than 1 cycle difference between
- * low and high and add low and high to get the actual
- * divisor. The base PLL is 208 MHz. Writing 0x00 will
- * divide by 1 and 1 so the highest frequency possible
- * is 104 MHz.
- *
- * e.g. 0x54 =>
- * f = 208 / ((5+1) + (4+1)) = 208 / 11 = 18.9 MHz
- */
- u16 val = readw(syscon_vbase + U300_SYSCON_MMF0R) &
- U300_SYSCON_MMF0R_MASK;
- switch (val) {
- case 0x0054:
- return 18900000;
- case 0x0044:
- return 20800000;
- case 0x0043:
- return 23100000;
- case 0x0033:
- return 26000000;
- case 0x0032:
- return 29700000;
- case 0x0022:
- return 34700000;
- case 0x0021:
- return 41600000;
- case 0x0011:
- return 52000000;
- case 0x0000:
- return 104000000;
- default:
- break;
- }
- }
- default:
- break;
- }
- return parent_rate;
-}
-
-static long
-mclk_clk_round_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long *prate)
-{
- if (rate <= 18900000)
- return 18900000;
- if (rate <= 20800000)
- return 20800000;
- if (rate <= 23100000)
- return 23100000;
- if (rate <= 26000000)
- return 26000000;
- if (rate <= 29700000)
- return 29700000;
- if (rate <= 34700000)
- return 34700000;
- if (rate <= 41600000)
- return 41600000;
- /* Highest rate */
- return 52000000;
-}
-
-static int mclk_clk_set_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long parent_rate)
-{
- u16 val;
- u16 reg;
-
- switch (rate) {
- case 18900000:
- val = 0x0054;
- break;
- case 20800000:
- val = 0x0044;
- break;
- case 23100000:
- val = 0x0043;
- break;
- case 26000000:
- val = 0x0033;
- break;
- case 29700000:
- val = 0x0032;
- break;
- case 34700000:
- val = 0x0022;
- break;
- case 41600000:
- val = 0x0021;
- break;
- case 52000000:
- val = 0x0011;
- break;
- case 104000000:
- val = 0x0000;
- break;
- default:
- return -EINVAL;
- }
-
- reg = readw(syscon_vbase + U300_SYSCON_MMF0R) &
- ~U300_SYSCON_MMF0R_MASK;
- writew(reg | val, syscon_vbase + U300_SYSCON_MMF0R);
- return 0;
-}
-
-static const struct clk_ops mclk_ops = {
- .prepare = mclk_clk_prepare,
- .recalc_rate = mclk_clk_recalc_rate,
- .round_rate = mclk_clk_round_rate,
- .set_rate = mclk_clk_set_rate,
-};
-
-static struct clk_hw * __init
-mclk_clk_register(struct device *dev, const char *name,
- const char *parent_name, bool is_mspro)
-{
- struct clk_hw *hw;
- struct clk_mclk *mclk;
- struct clk_init_data init;
- int ret;
-
- mclk = kzalloc(sizeof(*mclk), GFP_KERNEL);
- if (!mclk)
- return ERR_PTR(-ENOMEM);
-
- init.name = "mclk";
- init.ops = &mclk_ops;
- init.flags = 0;
- init.parent_names = (parent_name ? &parent_name : NULL);
- init.num_parents = (parent_name ? 1 : 0);
- mclk->hw.init = &init;
- mclk->is_mspro = is_mspro;
-
- hw = &mclk->hw;
- ret = clk_hw_register(dev, hw);
- if (ret) {
- kfree(mclk);
- hw = ERR_PTR(ret);
- }
-
- return hw;
-}
-
-static void __init of_u300_syscon_mclk_init(struct device_node *np)
-{
- struct clk_hw *hw;
- const char *clk_name = np->name;
- const char *parent_name;
-
- parent_name = of_clk_get_parent_name(np, 0);
- hw = mclk_clk_register(NULL, clk_name, parent_name, false);
- if (!IS_ERR(hw))
- of_clk_add_hw_provider(np, of_clk_hw_simple_get, hw);
-}
-
-static const struct of_device_id u300_clk_match[] __initconst = {
- {
- .compatible = "fixed-clock",
- .data = of_fixed_clk_setup,
- },
- {
- .compatible = "fixed-factor-clock",
- .data = of_fixed_factor_clk_setup,
- },
- {
- .compatible = "stericsson,u300-syscon-clk",
- .data = of_u300_syscon_clk_init,
- },
- {
- .compatible = "stericsson,u300-syscon-mclk",
- .data = of_u300_syscon_mclk_init,
- },
- {}
-};
-
-
-void __init u300_clk_init(void __iomem *base)
-{
- u16 val;
-
- syscon_vbase = base;
-
- /* Set system to run at PLL208, max performance, a known state. */
- val = readw(syscon_vbase + U300_SYSCON_CCR);
- val &= ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
- writew(val, syscon_vbase + U300_SYSCON_CCR);
- /* Wait for the PLL208 to lock if not locked in yet */
- while (!(readw(syscon_vbase + U300_SYSCON_CSR) &
- U300_SYSCON_CSR_PLL208_LOCK_IND));
-
- /* Power management enable */
- val = readw(syscon_vbase + U300_SYSCON_PMCR);
- val |= U300_SYSCON_PMCR_PWR_MGNT_ENABLE;
- writew(val, syscon_vbase + U300_SYSCON_PMCR);
-
- of_clk_init(u300_clk_match);
-}
projects / linux-2.6-microblaze.git / commitdiff