omap_hsmmc: only MMC1 allows HCTL.SDVS != 1.8V

Based on a patch from Tony Lindgren ... after initialization,
never change HCTL.SDVS except for MMC1.  The other controller
instances only support 1.8V in that field, although they can
suport other card/SDIO/eMMC/... voltages with level shifting
solutions such as external transceivers.

MMC2 behavior sanity tested on Overo/WLAN, OMAP3430 SDP, and
custom hardware.  MMC1 also sanity tested on those platforms
plus Beagle.  This also fixes a bug preventing MMC2 (and also
presumably MMC3) from powering down when requested.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 4dba486..3bfd0fa 100644 (file)
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -55,6 +55,7 @@
 #define VS30                   (1 << 25)
 #define SDVS18                 (0x5 << 9)
 #define SDVS30                 (0x6 << 9)
+#define SDVS33                 (0x7 << 9)
 #define SDVSCLR                        0xFFFFF1FF
 #define SDVSDET                        0x00000400
 #define AUTOIDLE               0x1
@@ -456,13 +457,20 @@ static irqreturn_t mmc_omap_irq(int irq, void *dev_id)
 }
 
 /*
- * Switch MMC operating voltage
+ * Switch MMC interface voltage ... only relevant for MMC1.
+ *
+ * MMC2 and MMC3 use fixed 1.8V levels, and maybe a transceiver.
+ * The MMC2 transceiver controls are used instead of DAT4..DAT7.
+ * Some chips, like eMMC ones, use internal transceivers.
  */
 static int omap_mmc_switch_opcond(struct mmc_omap_host *host, int vdd)
 {
        u32 reg_val = 0;
        int ret;
 
+       if (host->id != OMAP_MMC1_DEVID)
+               return 0;
+
        /* Disable the clocks */
        clk_disable(host->fclk);
        clk_disable(host->iclk);
@@ -485,19 +493,26 @@ static int omap_mmc_switch_opcond(struct mmc_omap_host *host, int vdd)
        OMAP_HSMMC_WRITE(host->base, HCTL,
                OMAP_HSMMC_READ(host->base, HCTL) & SDVSCLR);
        reg_val = OMAP_HSMMC_READ(host->base, HCTL);
+
        /*
         * If a MMC dual voltage card is detected, the set_ios fn calls
         * this fn with VDD bit set for 1.8V. Upon card removal from the
         * slot, omap_mmc_set_ios sets the VDD back to 3V on MMC_POWER_OFF.
         *
-        * Only MMC1 supports 3.0V.  MMC2 will not function if SDVS30 is
-        * set in HCTL.
+        * Cope with a bit of slop in the range ... per data sheets:
+        *  - "1.8V" for vdds_mmc1/vdds_mmc1a can be up to 2.45V max,
+        *    but recommended values are 1.71V to 1.89V
+        *  - "3.0V" for vdds_mmc1/vdds_mmc1a can be up to 3.5V max,
+        *    but recommended values are 2.7V to 3.3V
+        *
+        * Board setup code shouldn't permit anything very out-of-range.
+        * TWL4030-family VMMC1 and VSIM regulators are fine (avoiding the
+        * middle range) but VSIM can't power DAT4..DAT7 at more than 3V.
         */
-       if (host->id == OMAP_MMC1_DEVID && (((1 << vdd) == MMC_VDD_32_33) ||
-                               ((1 << vdd) == MMC_VDD_33_34)))
-               reg_val |= SDVS30;
-       if ((1 << vdd) == MMC_VDD_165_195)
+       if ((1 << vdd) <= MMC_VDD_23_24)
                reg_val |= SDVS18;
+       else
+               reg_val |= SDVS30;
 
        OMAP_HSMMC_WRITE(host->base, HCTL, reg_val);
 
@@ -759,10 +774,14 @@ static void omap_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
        case MMC_POWER_OFF:
                mmc_slot(host).set_power(host->dev, host->slot_id, 0, 0);
                /*
-                * Reset bus voltage to 3V if it got set to 1.8V earlier.
+                * Reset interface voltage to 3V if it's 1.8V now;
+                * only relevant on MMC-1, the others always use 1.8V.
+                *
                 * REVISIT: If we are able to detect cards after unplugging
                 * a 1.8V card, this code should not be needed.
                 */
+               if (host->id != OMAP_MMC1_DEVID)
+                       break;
                if (!(OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET)) {
                        int vdd = fls(host->mmc->ocr_avail) - 1;
                        if (omap_mmc_switch_opcond(host, vdd) != 0)
@@ -786,7 +805,9 @@ static void omap_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
        }
 
        if (host->id == OMAP_MMC1_DEVID) {
-               /* Only MMC1 can operate at 3V/1.8V */
+               /* Only MMC1 can interface at 3V without some flavor
+                * of external transceiver; but they all handle 1.8V.
+                */
                if ((OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET) &&
                        (ios->vdd == DUAL_VOLT_OCR_BIT)) {
                                /*
@@ -1139,7 +1160,9 @@ static int omap_mmc_suspend(struct platform_device *pdev, pm_message_t state)
                                                " level suspend\n");
                        }
 
-                       if (!(OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET)) {
+                       if (host->id == OMAP_MMC1_DEVID
+                                       && !(OMAP_HSMMC_READ(host->base, HCTL)
+                                                       & SDVSDET)) {
                                OMAP_HSMMC_WRITE(host->base, HCTL,
                                        OMAP_HSMMC_READ(host->base, HCTL)
                                        & SDVSCLR);