- atmel,at91sam9x60
- const: atmel,at91sam9
+ - items:
+ - enum:
+ - overkiz,kizboxmini-base # Overkiz kizbox Mini Base Board
+ - overkiz,kizboxmini-mb # Overkiz kizbox Mini Mother Board
+ - overkiz,kizboxmini-rd # Overkiz kizbox Mini RailDIN
+ - overkiz,smartkiz # Overkiz SmartKiz Board
+ - const: atmel,at91sam9g25
+ - const: atmel,at91sam9x5
+ - const: atmel,at91sam9
+
- items:
- enum:
- atmel,at91sam9g15
- const: atmel,sama5d2
- const: atmel,sama5
+ - description: Microchip SAMA5D27 WLSOM1
+ items:
+ - const: microchip,sama5d27-wlsom1
+ - const: atmel,sama5d27
+ - const: atmel,sama5d2
+ - const: atmel,sama5
+
+ - description: Microchip SAMA5D27 WLSOM1 Evaluation Kit
+ items:
+ - const: microchip,sama5d27-wlsom1-ek
+ - const: microchip,sama5d27-wlsom1
+ - const: atmel,sama5d27
+ - const: atmel,sama5d2
+ - const: atmel,sama5
+
- items:
- const: atmel,sama5d27
- const: atmel,sama5d2
at91-ariag25.dtb \
at91-ariettag25.dtb \
at91-cosino_mega2560.dtb \
- at91-kizboxmini.dtb \
+ at91-kizboxmini-base.dtb \
+ at91-kizboxmini-mb.dtb \
+ at91-kizboxmini-rd.dtb \
+ at91-smartkiz.dtb \
at91-wb45n.dtb \
at91sam9g15ek.dtb \
at91sam9g25ek.dtb \
at91-kizbox3-hs.dtb \
at91-nattis-2-natte-2.dtb \
at91-sama5d27_som1_ek.dtb \
+ at91-sama5d27_wlsom1_ek.dtb \
at91-sama5d2_ptc_ek.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
};
};
- ahb {
- apb {
- tcb0: timer@fffa0000 {
- timer@0 {
- compatible = "atmel,tcb-timer";
- reg = <0>, <1>;
- };
-
- timer@2 {
- compatible = "atmel,tcb-timer";
- reg = <2>;
- };
- };
-
- macb0: ethernet@fffc4000 {
- phy-mode = "mii";
- pinctrl-0 = <&pinctrl_macb_rmii
- &pinctrl_macb_rmii_mii_alt>;
- status = "okay";
- };
-
- usart3: serial@fffd0000 {
- status = "okay";
- };
-
- dbgu: serial@fffff200 {
- status = "okay";
- };
-
- watchdog@fffffd40 {
- timeout-sec = <15>;
- atmel,max-heartbeat-sec = <16>;
- atmel,min-heartbeat-sec = <0>;
- status = "okay";
- };
- };
-
- usb0: ohci@500000 {
- num-ports = <1>;
- status = "okay";
- };
-
- ebi: ebi@10000000 {
- status = "okay";
-
- nand_controller: nand-controller {
- status = "okay";
- pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
- pinctrl-names = "default";
-
- nand@3 {
- reg = <0x3 0x0 0x800000>;
- rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
- cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
- nand-bus-width = <8>;
- nand-ecc-mode = "soft";
- nand-on-flash-bbt;
- label = "atmel_nand";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- bootstrap@0 {
- label = "bootstrap";
- reg = <0x0 0x20000>;
- };
-
- ubi@20000 {
- label = "ubi";
- reg = <0x20000 0x7fe0000>;
- };
- };
- };
- };
- };
- };
-
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
};
};
- i2c-gpio-0 {
- status = "okay";
-
- rtc: pcf8563@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
- };
-
pwm_leds {
compatible = "pwm-leds";
&pinctrl_tcb1_tiob0>;
};
};
+
+&tcb0 {
+ timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>, <1>;
+ };
+
+ timer@2 {
+ compatible = "atmel,tcb-timer";
+ reg = <2>;
+ };
+};
+
+&ebi {
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
+ pinctrl-names = "default";
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ bootstrap@0 {
+ label = "bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ ubi@20000 {
+ label = "ubi";
+ reg = <0x20000 0x7fe0000>;
+ };
+ };
+ };
+};
+
+&macb0 {
+ phy-mode = "mii";
+ pinctrl-0 = <&pinctrl_macb_rmii
+ &pinctrl_macb_rmii_mii_alt>;
+ status = "okay";
+};
+
+&usart3 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+};
+
+&watchdog {
+ timeout-sec = <15>;
+ atmel,max-heartbeat-sec = <16>;
+ atmel,min-heartbeat-sec = <0>;
+ status = "okay";
+};
+
+&usb0 {
+ num-ports = <1>;
+ status = "okay";
+};
+
+&i2c_gpio0 {
+ status = "okay";
+
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * at91-kizboxmini-base.dts - Device Tree file for Overkiz Kizbox mini
+ * base board
+ *
+ * Copyright (C) 2015 Overkiz SAS
+ * Author: Antoine Aubert <a.aubert@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+ model = "Overkiz Kizbox Mini";
+ compatible = "overkiz,kizboxmini-base", "atmel,at91sam9g25",
+ "atmel,at91sam9x5", "atmel,at91sam9";
+};
+
+&pinctrl_usart0 {
+ atmel,pins =
+ <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_NONE
+ AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-kizboxmini.dts - Device Tree file for Overkiz Kizbox mini board
+ *
+ * Copyright (C) 2014-2018 Overkiz SAS
+ * Author: Antoine Aubert <a.aubert@overkiz.com>
+ * Gaël Portay <g.portay@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ * Dorian Rocipon <d.rocipon@overkiz.com>
+ */
+#include "at91sam9g25.dtsi"
+
+/ {
+ chosen {
+ bootargs = "ubi.mtd=ubi";
+ stdout-path = &dbgu;
+ };
+
+ memory {
+ reg = <0x20000000 0x8000000>;
+ };
+
+ clocks {
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ adc_op_clk {
+ status = "disabled";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ prog {
+ label = "PB_PROG";
+ gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
+ linux,code = <0x102>;
+ wakeup-source;
+ };
+
+ reset {
+ label = "PB_RST";
+ gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
+ linux,code = <0x100>;
+ wakeup-source;
+ };
+ };
+
+ leds: pwm_leds {
+ compatible = "pwm-leds";
+
+ led_blue: pwm_blue {
+ label = "pwm:blue:user";
+ pwms = <&pwm0 2 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "none";
+ status = "disabled";
+ };
+
+ led_green: pwm_green {
+ label = "pwm:green:user";
+ pwms = <&pwm0 0 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "default-on";
+ };
+
+ led_red: pwm_red {
+ label = "pwm:red:user";
+ pwms = <&pwm0 1 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "default-on";
+ };
+ };
+};
+
+&usart0 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+};
+
+&macb0 {
+ phy-mode = "rmii";
+ status = "okay";
+};
+
+&pwm0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_pwm0_1
+ &pinctrl_pwm0_pwm1_1
+ &pinctrl_pwm0_pwm2_1>;
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&adc0 {
+ status = "disabled";
+};
+
+&rtc {
+ status = "disabled";
+};
+
+&ebi {
+ pinctrl-0 = <&pinctrl_ebi_addr_nand
+ &pinctrl_ebi_data_0_7>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_nand_oe_we
+ &pinctrl_nand_cs
+ &pinctrl_nand_rb>;
+ pinctrl-names = "default";
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ bootstrap@0 {
+ label = "bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ ubi@20000 {
+ label = "ubi";
+ reg = <0x20000 0x7fe0000>;
+ };
+ };
+ };
+};
+
+&usb0 {
+ num-ports = <1>;
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2015-2018 Overkiz SAS
+ * Author: Mickael Gardet <m.gardet@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+ model = "Overkiz Kizbox Mini Mother Board";
+ compatible = "overkiz,kizboxmini-mb", "atmel,at91sam9g25",
+ "atmel,at91sam9x5", "atmel,at91sam9";
+};
+
+&usb0 {
+ num-ports = <2>;
+};
+
+&rtc {
+ status = "okay";
+};
+
+&led_blue {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2015-2018 Overkiz SAS
+ * Author: Mickael Gardet <m.gardet@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+ model = "Overkiz Kizbox Mini RailDIN";
+ compatible = "overkiz,kizboxmini-rd", "atmel,at91sam9g25",
+ "atmel,at91sam9x5", "atmel,at91sam9";
+
+ clocks {
+ adc_op_clk {
+ status = "okay";
+ };
+ };
+};
+
+&pinctrl {
+ adc0 {
+ pinctrl_adc0_ad5: adc0_ad5-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+};
+
+&usart0 {
+ status = "disabled";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&led_blue {
+ status = "okay";
+};
+
+&adc0 {
+ atmel,adc-vref = <2500>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_ad5>;
+ atmel,adc-channels-used = <0x0020>;
+ status = "okay";
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * at91-kizboxmini.dts - Device Tree file for Overkiz Kizbox mini board
- *
- * Copyright (C) 2014 Gaël PORTAY <g.portay@overkiz.com>
- */
-/dts-v1/;
-#include "at91sam9g25.dtsi"
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
- model = "Overkiz Kizbox mini";
- compatible = "overkiz,kizboxmini", "atmel,at91sam9g25", "atmel,at91sam9x5", "atmel,at91sam9";
-
- chosen {
- bootargs = "ubi.mtd=ubi";
- stdout-path = &dbgu;
- };
-
- memory {
- reg = <0x20000000 0x8000000>;
- };
-
- clocks {
- slow_xtal {
- clock-frequency = <32768>;
- };
-
- main_xtal {
- clock-frequency = <12000000>;
- };
- };
-
- ahb {
- nand0: nand@40000000 {
- nand-bus-width = <8>;
- nand-ecc-mode = "hw";
- atmel,has-pmecc;
- atmel,pmecc-cap = <4>;
- atmel,pmecc-sector-size = <512>;
- nand-on-flash-bbt;
- status = "okay";
- };
- };
-
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
-
- prog {
- label = "PB_PROG";
- gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
- linux,code = <0x102>;
- wakeup-source;
- };
-
- reset {
- label = "PB_RST";
- gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
- linux,code = <0x100>;
- wakeup-source;
- };
- };
-
- pwm_leds {
- compatible = "pwm-leds";
-
- green {
- label = "pwm:green:user";
- pwms = <&pwm0 0 10000000 0>;
- max-brightness = <255>;
- linux,default-trigger = "default-on";
- };
-
- red {
- label = "pwm:red:user";
- pwms = <&pwm0 1 10000000 0>;
- max-brightness = <255>;
- linux,default-trigger = "default-on";
- };
- };
-};
-
-&dbgu {
- status = "okay";
-};
-
-&ebi {
- pinctrl-0 = <&pinctrl_ebi_addr_nand
- &pinctrl_ebi_data_0_7>;
- pinctrl-names = "default";
- status = "okay";
-
- nand-controller {
- pinctrl-0 = <&pinctrl_nand_oe_we
- &pinctrl_nand_cs
- &pinctrl_nand_rb>;
- pinctrl-names = "default";
- status = "okay";
-
- nand@3 {
- reg = <0x3 0x0 0x800000>;
- rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
- cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
- nand-bus-width = <8>;
- nand-ecc-mode = "hw";
- nand-ecc-strength = <4>;
- nand-ecc-step-size = <512>;
- nand-on-flash-bbt;
- label = "atmel_nand";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- bootstrap@0 {
- label = "bootstrap";
- reg = <0x0 0x20000>;
- };
-
- ubi@20000 {
- label = "ubi";
- reg = <0x20000 0x7fe0000>;
- };
- };
- };
- };
-};
-
-&macb0 {
- phy-mode = "rmii";
- status = "okay";
-};
-
-&pwm0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm0_pwm0_1
- &pinctrl_pwm0_pwm1_1>;
- status = "okay";
-};
-
-&tcb0 {
- timer@0 {
- compatible = "atmel,tcb-timer";
- reg = <0>;
- };
-
- timer@1 {
- compatible = "atmel,tcb-timer";
- reg = <1>;
- };
-};
-
-&usart0 {
- status = "okay";
-};
-
-&usb0 {
- num-ports = <1>;
- status = "okay";
-};
-
-&usb1 {
- status = "okay";
-};
-
-&watchdog {
- status = "okay";
-};
*/
/dts-v1/;
#include "at91-linea.dtsi"
-#include "sama5d3_lcd.dtsi"
#include "at91-natte.dtsi"
/ {
};
ahb {
+ sdmmc0: sdio-host@a0000000 {
+ microchip,sdcal-inverted;
+ };
+
apb {
qspi1: spi@f0024000 {
pinctrl-names = "default";
interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <0>, <0>;
dma-names = "tx", "rx";
+ i2c-analog-filter;
+ i2c-digital-filter;
+ i2c-digital-filter-width-ns = <35>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
+ i2c-analog-filter;
+ i2c-digital-filter;
+ i2c-digital-filter-width-ns = <35>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1_default>;
status = "okay";
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d27_wlsom1.dtsi - Device Tree file for SAMA5D27 WLSOM1
+ *
+ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Nicolas Ferre <nicolas.ferre@microcihp.com>
+ * Author: Eugen Hristev <eugen.hristev@microcihp.com>
+ */
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+ model = "Microchip SAMA5D27 WLSOM1";
+ compatible = "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <24000000>;
+ };
+ };
+};
+
+&flx1 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+
+ uart6: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+ clock-names = "usart";
+ pinctrl-0 = <&pinctrl_flx1_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&i2c0 {
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&i2c1 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ status = "okay";
+
+ mcp16502@5b {
+ compatible = "microchip,mcp16502";
+ reg = <0x5b>;
+ status = "okay";
+ lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>;
+
+ regulators {
+ vdd_3v3: VDD_IO {
+ regulator-name = "VDD_IO";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-mode = <4>;
+ };
+ };
+
+ vddio_ddr: VDD_DDR {
+ regulator-name = "VDD_DDR";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1200000>;
+ regulator-changeable-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1200000>;
+ regulator-changeable-in-suspend;
+ regulator-mode = <4>;
+ };
+ };
+
+ vdd_core: VDD_CORE {
+ regulator-name = "VDD_CORE";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1850000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-mode = <4>;
+ };
+ };
+
+ vdd_ddr: VDD_OTHER {
+ regulator-name = "VDD_OTHER";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <2>;
+ regulator-allowed-modes = <2>, <4>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ regulator-changeable-in-suspend;
+ regulator-mode = <4>;
+ };
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ regulator-changeable-in-suspend;
+ regulator-mode = <4>;
+ };
+ };
+
+ LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+
+ regulator-state-standby {
+ regulator-on-in-suspend;
+ };
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&macb0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_default>;
+ phy-mode = "rmii";
+
+ ethernet-phy@0 {
+ reg = <0x0>;
+ interrupt-parent = <&pioA>;
+ interrupts = <PIN_PB24 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_phy_irq>;
+ };
+};
+
+&pmc {
+ atmel,osc-bypass;
+};
+
+&qspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi1_default>;
+ status = "disabled";
+
+ qspi1_flash: spi_flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+ m25p,fast-read;
+ status = "disabled";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader@40000 {
+ label = "bootloader";
+ reg = <0x40000 0xc0000>;
+ };
+
+ bootloaderenvred@100000 {
+ label = "bootloader env redundant";
+ reg = <0x100000 0x40000>;
+ };
+
+ bootloaderenv@140000 {
+ label = "bootloader env";
+ reg = <0x140000 0x40000>;
+ };
+
+ dtb@180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+ };
+};
+
+&pioA {
+ pinctrl_flx1_default: flx1_usart_default {
+ pinmux = <PIN_PA24__FLEXCOM1_IO0>,
+ <PIN_PA23__FLEXCOM1_IO1>,
+ <PIN_PA25__FLEXCOM1_IO3>,
+ <PIN_PA26__FLEXCOM1_IO4>;
+ bias-disable;
+ };
+
+ pinctrl_i2c0_default: i2c0_default {
+ pinmux = <PIN_PD21__TWD0>,
+ <PIN_PD22__TWCK0>;
+ bias-disable;
+ };
+
+ pinctrl_i2c1_default: i2c1_default {
+ pinmux = <PIN_PD19__TWD1>,
+ <PIN_PD20__TWCK1>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_default: macb0_default {
+ pinmux = <PIN_PB14__GTXCK>,
+ <PIN_PB15__GTXEN>,
+ <PIN_PB16__GRXDV>,
+ <PIN_PB17__GRXER>,
+ <PIN_PB18__GRX0>,
+ <PIN_PB19__GRX1>,
+ <PIN_PB20__GTX0>,
+ <PIN_PB21__GTX1>,
+ <PIN_PB22__GMDC>,
+ <PIN_PB23__GMDIO>;
+ bias-disable;
+ };
+
+ pinctrl_macb0_phy_irq: macb0_phy_irq {
+ pinmux = <PIN_PB24__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_qspi1_default: qspi1_default {
+ pinmux = <PIN_PB5__QSPI1_SCK>,
+ <PIN_PB6__QSPI1_CS>,
+ <PIN_PB7__QSPI1_IO0>,
+ <PIN_PB8__QSPI1_IO1>,
+ <PIN_PB9__QSPI1_IO2>,
+ <PIN_PB10__QSPI1_IO3>;
+ bias-pull-up;
+ };
+};
+
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d27_wlsom1_ek.dts - Device Tree file for SAMA5D27 WLSOM1 EK
+ *
+ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Nicolas Ferre <nicolas.ferre@microcihp.com>
+ */
+/dts-v1/;
+#include "at91-sama5d27_wlsom1.dtsi"
+
+/ {
+ model = "Microchip SAMA5D27 WLSOM1 EK";
+ compatible = "microchip,sama5d27-wlsom1-ek", "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+ aliases {
+ serial0 = &uart0; /* DBGU */
+ serial1 = &uart6; /* BT */
+ serial2 = &uart5; /* mikro BUS 2 */
+ serial3 = &uart3; /* mikro BUS 1 */
+ i2c1 = &i2c1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio_default>;
+ status = "okay";
+
+ sw4 {
+ label = "USER BUTTON";
+ gpios = <&pioA PIN_PB2 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_gpio_default>;
+ status = "okay";
+
+ red {
+ label = "red";
+ gpios = <&pioA PIN_PA6 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "green";
+ gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "blue";
+ gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&adc {
+ vddana-supply = <&vdd_3v3>;
+ vref-supply = <&vdd_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc_default>;
+ status = "okay";
+};
+
+&flx0 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+ status = "okay";
+
+ uart5: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
+ clock-names = "usart";
+ pinctrl-0 = <&pinctrl_flx0_default>;
+ pinctrl-names = "default";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+};
+
+&flx1 {
+ status = "okay";
+
+ uart6: serial@200 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+};
+
+&macb0 {
+ status = "okay";
+};
+
+&pioA {
+ /*
+ * There is no real pinmux for ADC, if the pin
+ * is not requested by another peripheral then
+ * the muxing is done when channel is enabled.
+ * Requesting pins for ADC is GPIO is
+ * encouraged to prevent conflicts and to
+ * disable bias in order to be in the same
+ * state when the pin is not muxed to the adc.
+ */
+ pinctrl_adc_default: adc_default {
+ pinmux = <PIN_PD25__GPIO>,
+ <PIN_PD26__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_flx0_default: flx0_usart_default {
+ pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+ <PIN_PB29__FLEXCOM0_IO1>;
+ bias-disable;
+ };
+
+ pinctrl_key_gpio_default: key_gpio_default {
+ pinmux = <PIN_PB2__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_led_gpio_default: led_gpio_default {
+ pinmux = <PIN_PA6__GPIO>,
+ <PIN_PA7__GPIO>,
+ <PIN_PA8__GPIO>;
+ bias-pull-down;
+ };
+
+ pinctrl_sdmmc0_default: sdmmc0_default {
+ cmd_data {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA2__SDMMC0_DAT0>,
+ <PIN_PA3__SDMMC0_DAT1>,
+ <PIN_PA4__SDMMC0_DAT2>,
+ <PIN_PA5__SDMMC0_DAT3>;
+ bias-disable;
+ };
+
+ ck_cd_vddsel {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA11__SDMMC0_VDDSEL>,
+ <PIN_PA12__SDMMC0_WP>,
+ <PIN_PA13__SDMMC0_CD>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart0_default: uart0_default {
+ pinmux = <PIN_PB26__URXD0>,
+ <PIN_PB27__UTXD0>;
+ bias-disable;
+ };
+
+ pinctrl_uart3_default: uart3_default {
+ pinmux = <PIN_PB11__URXD3>,
+ <PIN_PB12__UTXD3>;
+ bias-disable;
+ };
+
+ pinctrl_pwm0_default: pwm0_default {
+ pinmux = <PIN_PA31__PWML0>,
+ <PIN_PA30__PWMH0>;
+ bias-disable;
+ };
+
+ pinctrl_usb_default: usb_default {
+ pinmux = <PIN_PA10__GPIO>;
+ bias-disable;
+ };
+};
+
+&pwm0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_default>;
+ status = "okay";
+};
+
+&qspi1 {
+ status = "okay";
+
+ qspi1_flash: spi_flash@0 {
+ status = "okay";
+ };
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ mmc-ddr-3_3v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ status = "okay";
+};
+
+&shutdown_controller {
+ atmel,shdwc-debouncer = <976>;
+ atmel,wakeup-rtc-timer;
+
+ input@0 {
+ reg = <0>;
+ atmel,wakeup-type = "low";
+ };
+};
+
+&tcb0 {
+ timer0: timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>;
+ };
+
+ timer1: timer@1 {
+ compatible = "atmel,tcb-timer";
+ reg = <1>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+};
+
+&usb1 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0
+ &pioA PIN_PA10 GPIO_ACTIVE_HIGH
+ 0
+ >;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+};
+
+&usb2 {
+ phy_type = "hsic";
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017-2018 Overkiz SAS
+ * Author: Mickael Gardet <m.gardet@overkiz.com>
+ * Kévin Raymond <k.raymond@overkiz.com>
+ * Dorian Rocipon <d.rocipon@overkiz.com>
+ */
+/dts-v1/;
+#include "at91-kizboxmini-common.dtsi"
+
+/ {
+ model = "Overkiz SmartKiz";
+ compatible = "overkiz,smartkiz", "atmel,at91sam9g25",
+ "atmel,at91sam9x5", "atmel,at91sam9";
+
+ clocks {
+ adc_op_clk {
+ status = "okay";
+ };
+ };
+
+ aliases {
+ serial5 = &uart0;
+ };
+
+ pio_keys {
+ hk_reset {
+ label = "HK_RESET";
+ gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_rf {
+ label = "POWER_RF";
+ gpios = <&pioA 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_wifi {
+ label = "POWER_WIFI";
+ gpios = <&pioA 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&pinctrl {
+ i2c1 {
+ pinctrl_i2c1: i2c1-0 {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_PULL_UP
+ AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>;
+ };
+ };
+
+ adc0 {
+ pinctrl_adc0_ad0: adc0_ad0-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 11 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad5: adc0_ad5-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad6: adc0_ad6-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 17 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ pinctrl_adc0_ad11: adc0_ad11-0 {
+ /* pull-up disable */
+ atmel,pins = <AT91_PIOB 10 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+};
+
+&i2c1 {
+ dmas = <0>, <0>;
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "disabled";
+};
+
+&macb0 {
+ status = "disabled";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&leds {
+ blue {
+ status = "okay";
+ };
+};
+
+&adc0 {
+ atmel,adc-vref = <2500>;
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &pinctrl_adc0_ad0
+ &pinctrl_adc0_ad5
+ &pinctrl_adc0_ad6
+ &pinctrl_adc0_ad11
+ >;
+ atmel,adc-channels-used = <0x0861>;
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
usart0 {
pinctrl_usart0: usart0-0 {
atmel,pins =
- <AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart1 {
pinctrl_usart1: usart1-0 {
atmel,pins =
- <AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart2 {
pinctrl_usart2: usart2-0 {
atmel,pins =
- <AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart3 {
pinctrl_usart3: usart3-0 {
atmel,pins =
- <AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOB 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
uart0 {
pinctrl_uart0: uart0-0 {
atmel,pins =
- <AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_NONE
+ <AT91_PIOA 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP
AT91_PIOA 30 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
};
};
uart1 {
pinctrl_uart1: uart1-0 {
atmel,pins =
- <AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOB 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOB 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
};
status = "disabled";
};
- watchdog@fffffd40 {
+ watchdog: watchdog@fffffd40 {
compatible = "atmel,at91sam9260-wdt";
reg = <0xfffffd40 0x10>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
};
};
- i2c-gpio-0 {
+ i2c_gpio0: i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */
&pioA 24 GPIO_ACTIVE_HIGH /* scl */
usart0 {
pinctrl_usart0: usart0-0 {
atmel,pins =
- <AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
<AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart1 {
pinctrl_usart1: usart1-0 {
atmel,pins =
- <AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
<AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart2 {
pinctrl_usart2: usart2-0 {
atmel,pins =
- <AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
<AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart0 {
pinctrl_usart0: usart0-0 {
atmel,pins =
- <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart1 {
pinctrl_usart1: usart1-0 {
atmel,pins =
- <AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart2 {
pinctrl_usart2: usart2-0 {
atmel,pins =
- <AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart0 {
pinctrl_usart0: usart0-0 {
atmel,pins =
- <AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOB 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOB 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart1 {
pinctrl_usart1: usart1-0 {
atmel,pins =
- <AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart2 {
pinctrl_usart2: usart2-0 {
atmel,pins =
- <AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart3 {
pinctrl_usart3: usart3-0 {
atmel,pins =
- <AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_NONE
+ <AT91_PIOB 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart0 {
pinctrl_usart0: usart0-0 {
atmel,pins =
- <AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
<AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart1 {
pinctrl_usart1: usart1-0 {
atmel,pins =
- <AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
<AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart2 {
pinctrl_usart2: usart2-0 {
atmel,pins =
- <AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
<AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
usart3 {
pinctrl_usart3: usart3-0 {
atmel,pins =
- <AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE>,
+ <AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
<AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
};
interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 31>, <&pmc PMC_TYPE_GCK 31>, <&pmc PMC_TYPE_CORE PMC_MAIN>;
clock-names = "hclock", "multclk", "baseclk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 31>;
+ assigned-clock-rates = <480000000>;
status = "disabled";
};
interrupts = <32 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 32>, <&pmc PMC_TYPE_GCK 32>, <&pmc PMC_TYPE_CORE PMC_MAIN>;
clock-names = "hclock", "multclk", "baseclk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 32>;
+ assigned-clock-rates = <480000000>;
status = "disabled";
};
interrupts = <38 IRQ_TYPE_LEVEL_HIGH 7>;
#pwm-cells = <3>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+ status = "disabled";
};
sfr: sfr@f8030000 {
clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
};
- secumod@fc040000 {
+ pioBU: secumod@fc040000 {
compatible = "atmel,sama5d2-secumod", "syscon";
reg = <0xfc040000 0x100>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
};
tdes@fc044000 {
usart0_clk: usart0_clk {
#clock-cells = <0>;
reg = <12>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart1_clk: usart1_clk {
#clock-cells = <0>;
reg = <13>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart2_clk: usart2_clk {
#clock-cells = <0>;
reg = <14>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart3_clk: usart3_clk {
#clock-cells = <0>;
reg = <15>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
uart0_clk: uart0_clk {
#clock-cells = <0>;
reg = <16>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
twi0_clk: twi0_clk {
reg = <18>;
#clock-cells = <0>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
twi1_clk: twi1_clk {
#clock-cells = <0>;
reg = <19>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
twi2_clk: twi2_clk {
#clock-cells = <0>;
reg = <20>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
mci0_clk: mci0_clk {
spi0_clk: spi0_clk {
#clock-cells = <0>;
reg = <24>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
spi1_clk: spi1_clk {
#clock-cells = <0>;
reg = <25>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
tcb0_clk: tcb0_clk {
#clock-cells = <0>;
reg = <26>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
pwm_clk: pwm_clk {
adc_clk: adc_clk {
#clock-cells = <0>;
reg = <29>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
dma0_clk: dma0_clk {
ssc0_clk: ssc0_clk {
#clock-cells = <0>;
reg = <38>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
ssc1_clk: ssc1_clk {
#clock-cells = <0>;
reg = <39>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
sha_clk: sha_clk {
can0_clk: can0_clk {
#clock-cells = <0>;
reg = <40>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
can1_clk: can1_clk {
#clock-cells = <0>;
reg = <41>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
};
};
tcb1_clk: tcb1_clk {
#clock-cells = <0>;
reg = <27>;
+ atmel,clk-output-range = <0 166000000>;
};
};
};
uart0_clk: uart0_clk {
#clock-cells = <0>;
reg = <16>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
uart1_clk: uart1_clk {
#clock-cells = <0>;
reg = <17>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
};
};
projects / linux-2.6-microblaze.git / commitdiff