* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Initialize nbytes for internal sg commands
libata: Fix ata_busy_wait() kernel docs
pata_via: Correct missing comments
pata_atiixp: propogate cable detection hack from drivers/ide to the new driver
ahci/pata_jmicron: fix JMicron quirk
ata_sg_init(qc, sg, n_elem);
qc->nsect = buflen / ATA_SECT_SIZE;
+ qc->nbytes = buflen;
}
qc->private_data = &wait;
static int atiixp_pre_reset(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- static struct pci_bits atiixp_enable_bits[] = {
+ static const struct pci_bits atiixp_enable_bits[] = {
{ 0x48, 1, 0x01, 0x00 },
{ 0x48, 1, 0x08, 0x00 }
};
+ u8 udma;
if (!pci_test_config_bits(pdev, &atiixp_enable_bits[ap->port_no]))
return -ENOENT;
- ap->cbl = ATA_CBL_PATA80;
+ /* Hack from drivers/ide/pci. Really we want to know how to do the
+ raw detection not play follow the bios mode guess */
+ pci_read_config_byte(pdev, ATIIXP_IDE_UDMA_MODE + ap->port_no, &udma);
+ if ((udma & 0x07) >= 0x04 || (udma & 0x70) >= 0x40)
+ ap->cbl = ATA_CBL_PATA80;
+ else
+ ap->cbl = ATA_CBL_PATA40;
return ata_std_prereset(ap);
}
u32 reg;
- if (id->driver_data != 368) {
- /* Put the controller into AHCI mode in case the AHCI driver
- has not yet been loaded. This can be done with either
- function present */
+ /* PATA controller is fn 1, AHCI is fn 0 */
+ if (id->driver_data != 368 && PCI_FUNC(pdev->devfn) != 1)
+ return -ENODEV;
- /* FIXME: We may want a way to override this in future */
- pci_write_config_byte(pdev, 0x41, 0xa1);
-
- /* PATA controller is fn 1, AHCI is fn 0 */
- if (PCI_FUNC(pdev->devfn) != 1)
- return -ENODEV;
- }
- if ( id->driver_data == 365 || id->driver_data == 366) {
- /* The 365/66 have two PATA channels, redirect the second */
+ /* The 365/66 have two PATA channels, redirect the second */
+ if (id->driver_data == 365 || id->driver_data == 366) {
pci_read_config_dword(pdev, 0x80, ®);
reg |= (1 << 24); /* IDE1 to PATA IDE secondary */
pci_write_config_dword(pdev, 0x80, reg);
* VIA VT8233c - UDMA100
* VIA VT8235 - UDMA133
* VIA VT8237 - UDMA133
+ * VIA VT8237S - UDMA133
* VIA VT8251 - UDMA133
*
* Most registers remain compatible across chips. Others start reserved
#include <linux/libata.h>
#define DRV_NAME "pata_via"
-#define DRV_VERSION "0.2.0"
+#define DRV_VERSION "0.2.1"
/*
* The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
pci_read_config_dword(pdev, 0x40, &conf);
/* Enable dual function mode, AHCI on fn 0, IDE fn1 */
/* Set the class codes correctly and then direct IDE 0 */
- conf &= ~0x000F0200; /* Clear bit 9 and 16-19 */
- conf |= 0x00C20002; /* Set bit 1, 17, 22, 23 */
+ conf &= ~0x000FF200; /* Clear bit 9 and 12-19 */
+ conf |= 0x00C2A102; /* Set 1, 8, 13, 15, 17, 22, 23 */
pci_write_config_dword(pdev, 0x40, conf);
/* Reconfigure so that the PCI scanner discovers the
/**
* ata_busy_wait - Wait for a port status register
* @ap: Port to wait for.
+ * @bits: bits that must be clear
+ * @max: number of 10uS waits to perform
*
* Waits up to max*10 microseconds for the selected bits in the port's
* status register to be cleared.