DPRINTK("EXIT\n");
}
+/**
+ * ata_std_softreset - reset host port via ATA SRST
+ * @ap: port to reset
+ * @verbose: fail verbosely
+ * @classes: resulting classes of attached devices
+ *
+ * Reset host port using ATA SRST. This function is to be used
+ * as standard callback for ata_drive_*_reset() functions.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep)
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int ata_std_softreset(struct ata_port *ap, int verbose, unsigned int *classes)
+{
+ unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
+ unsigned int devmask = 0, err_mask;
+ u8 err;
+
+ DPRINTK("ENTER\n");
+
+ /* determine if device 0/1 are present */
+ if (ata_devchk(ap, 0))
+ devmask |= (1 << 0);
+ if (slave_possible && ata_devchk(ap, 1))
+ devmask |= (1 << 1);
+
+ /* devchk reports device presence without actual device on
+ * most SATA controllers. Check SStatus and turn devmask off
+ * if link is offline. Note that we should continue resetting
+ * even when it seems like there's no device.
+ */
+ if (ap->ops->scr_read && !sata_dev_present(ap))
+ devmask = 0;
+
+ /* select device 0 again */
+ ap->ops->dev_select(ap, 0);
+
+ /* issue bus reset */
+ DPRINTK("about to softreset, devmask=%x\n", devmask);
+ err_mask = ata_bus_softreset(ap, devmask);
+ if (err_mask) {
+ if (verbose)
+ printk(KERN_ERR "ata%u: SRST failed (err_mask=0x%x)\n",
+ ap->id, err_mask);
+ else
+ DPRINTK("EXIT, softreset failed (err_mask=0x%x)\n",
+ err_mask);
+ return -EIO;
+ }
+
+ /* determine by signature whether we have ATA or ATAPI devices */
+ classes[0] = ata_dev_try_classify(ap, 0, &err);
+ if (slave_possible && err != 0x81)
+ classes[1] = ata_dev_try_classify(ap, 1, &err);
+
+ DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]);
+ return 0;
+}
+
+/**
+ * sata_std_hardreset - reset host port via SATA phy reset
+ * @ap: port to reset
+ * @verbose: fail verbosely
+ * @class: resulting class of attached device
+ *
+ * SATA phy-reset host port using DET bits of SControl register.
+ * This function is to be used as standard callback for
+ * ata_drive_*_reset().
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep)
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int sata_std_hardreset(struct ata_port *ap, int verbose, unsigned int *class)
+{
+ u32 sstatus, serror;
+ unsigned long timeout = jiffies + (HZ * 5);
+
+ DPRINTK("ENTER\n");
+
+ /* Issue phy wake/reset */
+ scr_write_flush(ap, SCR_CONTROL, 0x301);
+
+ /*
+ * Couldn't find anything in SATA I/II specs, but AHCI-1.1
+ * 10.4.2 says at least 1 ms.
+ */
+ msleep(1);
+
+ scr_write_flush(ap, SCR_CONTROL, 0x300);
+
+ /* Wait for phy to become ready, if necessary. */
+ do {
+ msleep(200);
+ sstatus = scr_read(ap, SCR_STATUS);
+ if ((sstatus & 0xf) != 1)
+ break;
+ } while (time_before(jiffies, timeout));
+
+ /* Clear SError */
+ serror = scr_read(ap, SCR_ERROR);
+ scr_write(ap, SCR_ERROR, serror);
+
+ /* TODO: phy layer with polling, timeouts, etc. */
+ if (!sata_dev_present(ap)) {
+ *class = ATA_DEV_NONE;
+ DPRINTK("EXIT, link offline\n");
+ return 0;
+ }
+
+ if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
+ if (verbose)
+ printk(KERN_ERR "ata%u: COMRESET failed "
+ "(device not ready)\n", ap->id);
+ else
+ DPRINTK("EXIT, device not ready\n");
+ return -EIO;
+ }
+
+ *class = ata_dev_try_classify(ap, 0, NULL);
+
+ DPRINTK("EXIT, class=%u\n", *class);
+ return 0;
+}
+
+/**
+ * ata_std_postreset - standard postreset callback
+ * @ap: the target ata_port
+ * @classes: classes of attached devices
+ *
+ * This function is invoked after a successful reset. Note that
+ * the device might have been reset more than once using
+ * different reset methods before postreset is invoked.
+ * postreset is also reponsible for setting cable type.
+ *
+ * This function is to be used as standard callback for
+ * ata_drive_*_reset().
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep)
+ */
+void ata_std_postreset(struct ata_port *ap, unsigned int *classes)
+{
+ DPRINTK("ENTER\n");
+
+ /* set cable type */
+ if (ap->cbl == ATA_CBL_NONE && ap->flags & ATA_FLAG_SATA)
+ ap->cbl = ATA_CBL_SATA;
+
+ /* print link status */
+ if (ap->cbl == ATA_CBL_SATA)
+ sata_print_link_status(ap);
+
+ /* bail out if no device is present */
+ if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
+ DPRINTK("EXIT, no device\n");
+ return;
+ }
+
+ /* is double-select really necessary? */
+ if (classes[0] != ATA_DEV_NONE)
+ ap->ops->dev_select(ap, 1);
+ if (classes[1] != ATA_DEV_NONE)
+ ap->ops->dev_select(ap, 0);
+
+ /* re-enable interrupts & set up device control */
+ if (ap->ioaddr.ctl_addr) /* FIXME: hack. create a hook instead */
+ ata_irq_on(ap);
+
+ DPRINTK("EXIT\n");
+}
+
+/**
+ * ata_std_probe_reset - standard probe reset method
+ * @ap: prot to perform probe-reset
+ * @classes: resulting classes of attached devices
+ *
+ * The stock off-the-shelf ->probe_reset method.
+ *
+ * LOCKING:
+ * Kernel thread context (may sleep)
+ *
+ * RETURNS:
+ * 0 on success, -errno otherwise.
+ */
+int ata_std_probe_reset(struct ata_port *ap, unsigned int *classes)
+{
+ ata_reset_fn_t hardreset;
+
+ hardreset = NULL;
+ if (ap->cbl == ATA_CBL_SATA && ap->ops->scr_read)
+ hardreset = sata_std_hardreset;
+
+ return ata_drive_probe_reset(ap, ata_std_softreset, hardreset,
+ ata_std_postreset, classes);
+}
+
static int do_probe_reset(struct ata_port *ap, ata_reset_fn_t reset,
ata_postreset_fn_t postreset,
unsigned int *classes)
EXPORT_SYMBOL_GPL(sata_phy_reset);
EXPORT_SYMBOL_GPL(__sata_phy_reset);
EXPORT_SYMBOL_GPL(ata_bus_reset);
+EXPORT_SYMBOL_GPL(ata_std_softreset);
+EXPORT_SYMBOL_GPL(sata_std_hardreset);
+EXPORT_SYMBOL_GPL(ata_std_postreset);
+EXPORT_SYMBOL_GPL(ata_std_probe_reset);
EXPORT_SYMBOL_GPL(ata_drive_probe_reset);
EXPORT_SYMBOL_GPL(ata_port_disable);
EXPORT_SYMBOL_GPL(ata_ratelimit);
projects / linux-2.6-microblaze.git / commitdiff