struct spi_device *spi,
struct spi_transfer *tfr,
u32 cs,
- unsigned long xfer_time_us)
+ unsigned long long xfer_time_us)
{
struct bcm2835_spi *bs = spi_master_get_devdata(master);
unsigned long timeout;
{
struct bcm2835_spi *bs = spi_master_get_devdata(master);
unsigned long spi_hz, clk_hz, cdiv;
- unsigned long spi_used_hz, xfer_time_us;
+ unsigned long spi_used_hz;
+ unsigned long long xfer_time_us;
u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
/* set clock */
spi_used_hz = cdiv ? (clk_hz / cdiv) : (clk_hz / 65536);
bcm2835_wr(bs, BCM2835_SPI_CLK, cdiv);
- /* handle all the modes */
+ /* handle all the 3-wire mode */
if ((spi->mode & SPI_3WIRE) && (tfr->rx_buf))
cs |= BCM2835_SPI_CS_REN;
- if (spi->mode & SPI_CPOL)
- cs |= BCM2835_SPI_CS_CPOL;
- if (spi->mode & SPI_CPHA)
- cs |= BCM2835_SPI_CS_CPHA;
+ else
+ cs &= ~BCM2835_SPI_CS_REN;
/* for gpio_cs set dummy CS so that no HW-CS get changed
* we can not run this in bcm2835_spi_set_cs, as it does
bs->rx_len = tfr->len;
/* calculate the estimated time in us the transfer runs */
- xfer_time_us = tfr->len
+ xfer_time_us = (unsigned long long)tfr->len
* 9 /* clocks/byte - SPI-HW waits 1 clock after each byte */
- * 1000000 / spi_used_hz;
+ * 1000000;
+ do_div(xfer_time_us, spi_used_hz);
/* for short requests run polling*/
if (xfer_time_us <= BCM2835_SPI_POLLING_LIMIT_US)
return bcm2835_spi_transfer_one_irq(master, spi, tfr, cs);
}
+static int bcm2835_spi_prepare_message(struct spi_master *master,
+ struct spi_message *msg)
+{
+ struct spi_device *spi = msg->spi;
+ struct bcm2835_spi *bs = spi_master_get_devdata(master);
+ u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+
+ cs &= ~(BCM2835_SPI_CS_CPOL | BCM2835_SPI_CS_CPHA);
+
+ if (spi->mode & SPI_CPOL)
+ cs |= BCM2835_SPI_CS_CPOL;
+ if (spi->mode & SPI_CPHA)
+ cs |= BCM2835_SPI_CS_CPHA;
+
+ bcm2835_wr(bs, BCM2835_SPI_CS, cs);
+
+ return 0;
+}
+
static void bcm2835_spi_handle_err(struct spi_master *master,
struct spi_message *msg)
{
master->set_cs = bcm2835_spi_set_cs;
master->transfer_one = bcm2835_spi_transfer_one;
master->handle_err = bcm2835_spi_handle_err;
+ master->prepare_message = bcm2835_spi_prepare_message;
master->dev.of_node = pdev->dev.of_node;
bs = spi_master_get_devdata(master);
{
/* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */
- bool oldbit = !(word & 1);
+ u32 oldbit = (!(word & (1<<(bits-1)))) << 31;
/* clock starts at inactive polarity */
for (word <<= (32 - bits); likely(bits); bits--) {
{
/* if (cpol == 0) this is SPI_MODE_1; else this is SPI_MODE_3 */
- bool oldbit = !(word & (1 << 31));
+ u32 oldbit = (!(word & (1<<(bits-1)))) << 31;
/* clock starts at inactive polarity */
for (word <<= (32 - bits); likely(bits); bits--) {
bool rx_dma_busy;
};
+struct img_spfi_device_data {
+ bool gpio_requested;
+};
+
static inline u32 spfi_readl(struct img_spfi *spfi, u32 reg)
{
return readl(spfi->regs + reg);
cpu_relax();
}
- ret = spfi_wait_all_done(spfi);
- if (ret < 0)
- return ret;
-
if (rx_bytes > 0 || tx_bytes > 0) {
dev_err(spfi->dev, "PIO transfer timed out\n");
return -ETIMEDOUT;
}
+ ret = spfi_wait_all_done(spfi);
+ if (ret < 0)
+ return ret;
+
return 0;
}
static int img_spfi_setup(struct spi_device *spi)
{
- int ret;
-
- ret = gpio_request_one(spi->cs_gpio, (spi->mode & SPI_CS_HIGH) ?
- GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH,
- dev_name(&spi->dev));
- if (ret)
- dev_err(&spi->dev, "can't request chipselect gpio %d\n",
+ int ret = -EINVAL;
+ struct img_spfi_device_data *spfi_data = spi_get_ctldata(spi);
+
+ if (!spfi_data) {
+ spfi_data = kzalloc(sizeof(*spfi_data), GFP_KERNEL);
+ if (!spfi_data)
+ return -ENOMEM;
+ spfi_data->gpio_requested = false;
+ spi_set_ctldata(spi, spfi_data);
+ }
+ if (!spfi_data->gpio_requested) {
+ ret = gpio_request_one(spi->cs_gpio,
+ (spi->mode & SPI_CS_HIGH) ?
+ GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH,
+ dev_name(&spi->dev));
+ if (ret)
+ dev_err(&spi->dev, "can't request chipselect gpio %d\n",
spi->cs_gpio);
-
+ else
+ spfi_data->gpio_requested = true;
+ } else {
+ if (gpio_is_valid(spi->cs_gpio)) {
+ int mode = ((spi->mode & SPI_CS_HIGH) ?
+ GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH);
+
+ ret = gpio_direction_output(spi->cs_gpio, mode);
+ if (ret)
+ dev_err(&spi->dev, "chipselect gpio %d setup failed (%d)\n",
+ spi->cs_gpio, ret);
+ }
+ }
return ret;
}
static void img_spfi_cleanup(struct spi_device *spi)
{
- gpio_free(spi->cs_gpio);
+ struct img_spfi_device_data *spfi_data = spi_get_ctldata(spi);
+
+ if (spfi_data) {
+ if (spfi_data->gpio_requested)
+ gpio_free(spi->cs_gpio);
+ kfree(spfi_data);
+ spi_set_ctldata(spi, NULL);
+ }
}
static void img_spfi_config(struct spi_master *master, struct spi_device *spi,
static void omap2_mcspi_set_cs(struct spi_device *spi, bool enable)
{
+ struct omap2_mcspi *mcspi = spi_master_get_devdata(spi->master);
u32 l;
/* The controller handles the inverted chip selects
enable = !enable;
if (spi->controller_state) {
+ int err = pm_runtime_get_sync(mcspi->dev);
+ if (err < 0) {
+ dev_err(mcspi->dev, "failed to get sync: %d\n", err);
+ return;
+ }
+
l = mcspi_cached_chconf0(spi);
if (enable)
l |= OMAP2_MCSPI_CHCONF_FORCE;
mcspi_write_chconf0(spi, l);
+
+ pm_runtime_mark_last_busy(mcspi->dev);
+ pm_runtime_put_autosuspend(mcspi->dev);
}
}
#define ORION_SPI_DATA_OUT_REG 0x08
#define ORION_SPI_DATA_IN_REG 0x0c
#define ORION_SPI_INT_CAUSE_REG 0x10
+#define ORION_SPI_TIMING_PARAMS_REG 0x18
+
+#define ORION_SPI_TMISO_SAMPLE_MASK (0x3 << 6)
+#define ORION_SPI_TMISO_SAMPLE_1 (1 << 6)
+#define ORION_SPI_TMISO_SAMPLE_2 (2 << 6)
#define ORION_SPI_MODE_CPOL (1 << 11)
#define ORION_SPI_MODE_CPHA (1 << 12)
unsigned int min_divisor;
unsigned int max_divisor;
u32 prescale_mask;
+ bool is_errata_50mhz_ac;
};
struct orion_spi {
writel(reg, spi_reg(orion_spi, ORION_SPI_IF_CONFIG_REG));
}
+static void
+orion_spi_50mhz_ac_timing_erratum(struct spi_device *spi, unsigned int speed)
+{
+ u32 reg;
+ struct orion_spi *orion_spi;
+
+ orion_spi = spi_master_get_devdata(spi->master);
+
+ /*
+ * Erratum description: (Erratum NO. FE-9144572) The device
+ * SPI interface supports frequencies of up to 50 MHz.
+ * However, due to this erratum, when the device core clock is
+ * 250 MHz and the SPI interfaces is configured for 50MHz SPI
+ * clock and CPOL=CPHA=1 there might occur data corruption on
+ * reads from the SPI device.
+ * Erratum Workaround:
+ * Work in one of the following configurations:
+ * 1. Set CPOL=CPHA=0 in "SPI Interface Configuration
+ * Register".
+ * 2. Set TMISO_SAMPLE value to 0x2 in "SPI Timing Parameters 1
+ * Register" before setting the interface.
+ */
+ reg = readl(spi_reg(orion_spi, ORION_SPI_TIMING_PARAMS_REG));
+ reg &= ~ORION_SPI_TMISO_SAMPLE_MASK;
+
+ if (clk_get_rate(orion_spi->clk) == 250000000 &&
+ speed == 50000000 && spi->mode & SPI_CPOL &&
+ spi->mode & SPI_CPHA)
+ reg |= ORION_SPI_TMISO_SAMPLE_2;
+ else
+ reg |= ORION_SPI_TMISO_SAMPLE_1; /* This is the default value */
+
+ writel(reg, spi_reg(orion_spi, ORION_SPI_TIMING_PARAMS_REG));
+}
+
/*
* called only when no transfer is active on the bus
*/
orion_spi_mode_set(spi);
+ if (orion_spi->devdata->is_errata_50mhz_ac)
+ orion_spi_50mhz_ac_timing_erratum(spi, speed);
+
rc = orion_spi_baudrate_set(spi, speed);
if (rc)
return rc;
.prescale_mask = ARMADA_SPI_CLK_PRESCALE_MASK,
};
+static const struct orion_spi_dev armada_380_spi_dev_data = {
+ .typ = ARMADA_SPI,
+ .max_hz = 50000000,
+ .max_divisor = 1920,
+ .prescale_mask = ARMADA_SPI_CLK_PRESCALE_MASK,
+ .is_errata_50mhz_ac = true,
+};
+
static const struct of_device_id orion_spi_of_match_table[] = {
{
.compatible = "marvell,orion-spi",
},
{
.compatible = "marvell,armada-380-spi",
- .data = &armada_xp_spi_dev_data,
+ .data = &armada_380_spi_dev_data,
},
{
.compatible = "marvell,armada-390-spi",
xspi->tx_ptr = t->tx_buf;
xspi->rx_ptr = t->rx_buf;
remaining_words = t->len / xspi->bytes_per_word;
- reinit_completion(&xspi->done);
if (xspi->irq >= 0 && remaining_words > xspi->buffer_size) {
+ u32 isr;
use_irq = true;
- xspi->write_fn(XSPI_INTR_TX_EMPTY,
- xspi->regs + XIPIF_V123B_IISR_OFFSET);
- /* Enable the global IPIF interrupt */
- xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
- xspi->regs + XIPIF_V123B_DGIER_OFFSET);
/* Inhibit irq to avoid spurious irqs on tx_empty*/
cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
xspi->regs + XSPI_CR_OFFSET);
+ /* ACK old irqs (if any) */
+ isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
+ if (isr)
+ xspi->write_fn(isr,
+ xspi->regs + XIPIF_V123B_IISR_OFFSET);
+ /* Enable the global IPIF interrupt */
+ xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
+ xspi->regs + XIPIF_V123B_DGIER_OFFSET);
+ reinit_completion(&xspi->done);
}
while (remaining_words) {
remaining_words -= n_words;
}
- if (use_irq)
+ if (use_irq) {
xspi->write_fn(0, xspi->regs + XIPIF_V123B_DGIER_OFFSET);
+ xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
+ }
return t->len;
}
projects / linux-2.6-microblaze.git / commitdiff