+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
-** hp100.c
-** HP CASCADE Architecture Driver for 100VG-AnyLan Network Adapters
-**
-** $Id: hp100.c,v 1.58 2001/09/24 18:03:01 perex Exp perex $
-**
-** Based on the HP100 driver written by Jaroslav Kysela <perex@jcu.cz>
-** Extended for new busmaster capable chipsets by
-** Siegfried "Frieder" Loeffler (dg1sek) <floeff@mathematik.uni-stuttgart.de>
-**
-** Maintained by: Jaroslav Kysela <perex@perex.cz>
-**
-** This driver has only been tested with
-** -- HP J2585B 10/100 Mbit/s PCI Busmaster
-** -- HP J2585A 10/100 Mbit/s PCI
-** -- HP J2970A 10 Mbit/s PCI Combo 10base-T/BNC
-** -- HP J2973A 10 Mbit/s PCI 10base-T
-** -- HP J2573 10/100 ISA
-** -- Compex ReadyLink ENET100-VG4 10/100 Mbit/s PCI / EISA
-** -- Compex FreedomLine 100/VG 10/100 Mbit/s ISA / EISA / PCI
-**
-** but it should also work with the other CASCADE based adapters.
-**
-** TODO:
-** - J2573 seems to hang sometimes when in shared memory mode.
-** - Mode for Priority TX
-** - Check PCI registers, performance might be improved?
-** - To reduce interrupt load in busmaster, one could switch off
-** the interrupts that are used to refill the queues whenever the
-** queues are filled up to more than a certain threshold.
-** - some updates for EISA version of card
-**
-**
-**
-** 1.57c -> 1.58
-** - used indent to change coding-style
-** - added KTI DP-200 EISA ID
-** - ioremap is also used for low (<1MB) memory (multi-architecture support)
-**
-** 1.57b -> 1.57c - Arnaldo Carvalho de Melo <acme@conectiva.com.br>
-** - release resources on failure in init_module
-**
-** 1.57 -> 1.57b - Jean II
-** - fix spinlocks, SMP is now working !
-**
-** 1.56 -> 1.57
-** - updates for new PCI interface for 2.1 kernels
-**
-** 1.55 -> 1.56
-** - removed printk in misc. interrupt and update statistics to allow
-** monitoring of card status
-** - timing changes in xmit routines, relogin to 100VG hub added when
-** driver does reset
-** - included fix for Compex FreedomLine PCI adapter
-**
-** 1.54 -> 1.55
-** - fixed bad initialization in init_module
-** - added Compex FreedomLine adapter
-** - some fixes in card initialization
-**
-** 1.53 -> 1.54
-** - added hardware multicast filter support (doesn't work)
-** - little changes in hp100_sense_lan routine
-** - added support for Coax and AUI (J2970)
-** - fix for multiple cards and hp100_mode parameter (insmod)
-** - fix for shared IRQ
-**
-** 1.52 -> 1.53
-** - fixed bug in multicast support
-**
-*/
-
-#define HP100_DEFAULT_PRIORITY_TX 0
-
-#undef HP100_DEBUG
-#undef HP100_DEBUG_B /* Trace */
-#undef HP100_DEBUG_BM /* Debug busmaster code (PDL stuff) */
-
-#undef HP100_DEBUG_TRAINING /* Debug login-to-hub procedure */
-#undef HP100_DEBUG_TX
-#undef HP100_DEBUG_IRQ
-#undef HP100_DEBUG_RX
-
-#undef HP100_MULTICAST_FILTER /* Need to be debugged... */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/interrupt.h>
-#include <linux/eisa.h>
-#include <linux/pci.h>
-#include <linux/dma-mapping.h>
-#include <linux/spinlock.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/types.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/bitops.h>
-#include <linux/jiffies.h>
-
-#include <asm/io.h>
-
-#include "hp100.h"
-
-/*
- * defines
- */
-
-#define HP100_BUS_ISA 0
-#define HP100_BUS_EISA 1
-#define HP100_BUS_PCI 2
-
-#define HP100_REGION_SIZE 0x20 /* for ioports */
-#define HP100_SIG_LEN 8 /* same as EISA_SIG_LEN */
-
-#define HP100_MAX_PACKET_SIZE (1536 + 4)
-#define HP100_MIN_PACKET_SIZE 60
-
-#ifndef HP100_DEFAULT_RX_RATIO
-/* default - 75% onboard memory on the card are used for RX packets */
-#define HP100_DEFAULT_RX_RATIO 75
-#endif
-
-#ifndef HP100_DEFAULT_PRIORITY_TX
-/* default - don't enable transmit outgoing packets as priority */
-#define HP100_DEFAULT_PRIORITY_TX 0
-#endif
-
-/*
- * structures
- */
-
-struct hp100_private {
- spinlock_t lock;
- char id[HP100_SIG_LEN];
- u_short chip;
- u_short soft_model;
- u_int memory_size;
- u_int virt_memory_size;
- u_short rx_ratio; /* 1 - 99 */
- u_short priority_tx; /* != 0 - priority tx */
- u_short mode; /* PIO, Shared Mem or Busmaster */
- u_char bus;
- struct pci_dev *pci_dev;
- short mem_mapped; /* memory mapped access */
- void __iomem *mem_ptr_virt; /* virtual memory mapped area, maybe NULL */
- unsigned long mem_ptr_phys; /* physical memory mapped area */
- short lan_type; /* 10Mb/s, 100Mb/s or -1 (error) */
- int hub_status; /* was login to hub successful? */
- u_char mac1_mode;
- u_char mac2_mode;
- u_char hash_bytes[8];
-
- /* Rings for busmaster mode: */
- hp100_ring_t *rxrhead; /* Head (oldest) index into rxring */
- hp100_ring_t *rxrtail; /* Tail (newest) index into rxring */
- hp100_ring_t *txrhead; /* Head (oldest) index into txring */
- hp100_ring_t *txrtail; /* Tail (newest) index into txring */
-
- hp100_ring_t rxring[MAX_RX_PDL];
- hp100_ring_t txring[MAX_TX_PDL];
-
- u_int *page_vaddr_algn; /* Aligned virtual address of allocated page */
- u_long whatever_offset; /* Offset to bus/phys/dma address */
- int rxrcommit; /* # Rx PDLs committed to adapter */
- int txrcommit; /* # Tx PDLs committed to adapter */
-};
-
-/*
- * variables
- */
-#ifdef CONFIG_ISA
-static const char *hp100_isa_tbl[] = {
- "HWPF150", /* HP J2573 rev A */
- "HWP1950", /* HP J2573 */
-};
-#endif
-
-static const struct eisa_device_id hp100_eisa_tbl[] = {
- { "HWPF180" }, /* HP J2577 rev A */
- { "HWP1920" }, /* HP 27248B */
- { "HWP1940" }, /* HP J2577 */
- { "HWP1990" }, /* HP J2577 */
- { "CPX0301" }, /* ReadyLink ENET100-VG4 */
- { "CPX0401" }, /* FreedomLine 100/VG */
- { "" } /* Mandatory final entry ! */
-};
-MODULE_DEVICE_TABLE(eisa, hp100_eisa_tbl);
-
-static const struct pci_device_id hp100_pci_tbl[] = {
- {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_J2585A, PCI_ANY_ID, PCI_ANY_ID,},
- {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_J2585B, PCI_ANY_ID, PCI_ANY_ID,},
- {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_J2970A, PCI_ANY_ID, PCI_ANY_ID,},
- {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_J2973A, PCI_ANY_ID, PCI_ANY_ID,},
- {PCI_VENDOR_ID_COMPEX, PCI_DEVICE_ID_COMPEX_ENET100VG4, PCI_ANY_ID, PCI_ANY_ID,},
- {PCI_VENDOR_ID_COMPEX2, PCI_DEVICE_ID_COMPEX2_100VG, PCI_ANY_ID, PCI_ANY_ID,},
-/* {PCI_VENDOR_ID_KTI, PCI_DEVICE_ID_KTI_DP200, PCI_ANY_ID, PCI_ANY_ID }, */
- {} /* Terminating entry */
-};
-MODULE_DEVICE_TABLE(pci, hp100_pci_tbl);
-
-static int hp100_rx_ratio = HP100_DEFAULT_RX_RATIO;
-static int hp100_priority_tx = HP100_DEFAULT_PRIORITY_TX;
-static int hp100_mode = 1;
-
-module_param(hp100_rx_ratio, int, 0);
-module_param(hp100_priority_tx, int, 0);
-module_param(hp100_mode, int, 0);
-
-/*
- * prototypes
- */
-
-static int hp100_probe1(struct net_device *dev, int ioaddr, u_char bus,
- struct pci_dev *pci_dev);
-
-static int hp100_open(struct net_device *dev);
-static int hp100_close(struct net_device *dev);
-static netdev_tx_t hp100_start_xmit(struct sk_buff *skb,
- struct net_device *dev);
-static netdev_tx_t hp100_start_xmit_bm(struct sk_buff *skb,
- struct net_device *dev);
-static void hp100_rx(struct net_device *dev);
-static struct net_device_stats *hp100_get_stats(struct net_device *dev);
-static void hp100_misc_interrupt(struct net_device *dev);
-static void hp100_update_stats(struct net_device *dev);
-static void hp100_clear_stats(struct hp100_private *lp, int ioaddr);
-static void hp100_set_multicast_list(struct net_device *dev);
-static irqreturn_t hp100_interrupt(int irq, void *dev_id);
-static void hp100_start_interface(struct net_device *dev);
-static void hp100_stop_interface(struct net_device *dev);
-static void hp100_load_eeprom(struct net_device *dev, u_short ioaddr);
-static int hp100_sense_lan(struct net_device *dev);
-static int hp100_login_to_vg_hub(struct net_device *dev,
- u_short force_relogin);
-static int hp100_down_vg_link(struct net_device *dev);
-static void hp100_cascade_reset(struct net_device *dev, u_short enable);
-static void hp100_BM_shutdown(struct net_device *dev);
-static void hp100_mmuinit(struct net_device *dev);
-static void hp100_init_pdls(struct net_device *dev);
-static int hp100_init_rxpdl(struct net_device *dev,
- register hp100_ring_t *ringptr,
- register u_int *pdlptr);
-static int hp100_init_txpdl(struct net_device *dev,
- register hp100_ring_t *ringptr,
- register u_int *pdlptr);
-static void hp100_rxfill(struct net_device *dev);
-static void hp100_hwinit(struct net_device *dev);
-static void hp100_clean_txring(struct net_device *dev);
-#ifdef HP100_DEBUG
-static void hp100_RegisterDump(struct net_device *dev);
-#endif
-
-/* Conversion to new PCI API :
- * Convert an address in a kernel buffer to a bus/phys/dma address.
- * This work *only* for memory fragments part of lp->page_vaddr,
- * because it was properly DMA allocated via pci_alloc_consistent(),
- * so we just need to "retrieve" the original mapping to bus/phys/dma
- * address - Jean II */
-static inline dma_addr_t virt_to_whatever(struct net_device *dev, u32 *ptr)
-{
- struct hp100_private *lp = netdev_priv(dev);
- return ((u_long) ptr) + lp->whatever_offset;
-}
-
-static inline u_int pdl_map_data(struct hp100_private *lp, void *data)
-{
- return pci_map_single(lp->pci_dev, data,
- MAX_ETHER_SIZE, PCI_DMA_FROMDEVICE);
-}
-
-/* TODO: This function should not really be needed in a good design... */
-static void wait(void)
-{
- mdelay(1);
-}
-
-/*
- * probe functions
- * These functions should - if possible - avoid doing write operations
- * since this could cause problems when the card is not installed.
- */
-
-/*
- * Read board id and convert to string.
- * Effectively same code as decode_eisa_sig
- */
-static const char *hp100_read_id(int ioaddr)
-{
- int i;
- static char str[HP100_SIG_LEN];
- unsigned char sig[4], sum;
- unsigned short rev;
-
- hp100_page(ID_MAC_ADDR);
- sum = 0;
- for (i = 0; i < 4; i++) {
- sig[i] = hp100_inb(BOARD_ID + i);
- sum += sig[i];
- }
-
- sum += hp100_inb(BOARD_ID + i);
- if (sum != 0xff)
- return NULL; /* bad checksum */
-
- str[0] = ((sig[0] >> 2) & 0x1f) + ('A' - 1);
- str[1] = (((sig[0] & 3) << 3) | (sig[1] >> 5)) + ('A' - 1);
- str[2] = (sig[1] & 0x1f) + ('A' - 1);
- rev = (sig[2] << 8) | sig[3];
- sprintf(str + 3, "%04X", rev);
-
- return str;
-}
-
-#ifdef CONFIG_ISA
-static __init int hp100_isa_probe1(struct net_device *dev, int ioaddr)
-{
- const char *sig;
- int i;
-
- if (!request_region(ioaddr, HP100_REGION_SIZE, "hp100"))
- goto err;
-
- if (hp100_inw(HW_ID) != HP100_HW_ID_CASCADE) {
- release_region(ioaddr, HP100_REGION_SIZE);
- goto err;
- }
-
- sig = hp100_read_id(ioaddr);
- release_region(ioaddr, HP100_REGION_SIZE);
-
- if (sig == NULL)
- goto err;
-
- i = match_string(hp100_isa_tbl, ARRAY_SIZE(hp100_isa_tbl), sig);
- if (i < 0)
- goto err;
-
- return hp100_probe1(dev, ioaddr, HP100_BUS_ISA, NULL);
- err:
- return -ENODEV;
-}
-/*
- * Probe for ISA board.
- * EISA and PCI are handled by device infrastructure.
- */
-
-static int __init hp100_isa_probe(struct net_device *dev, int addr)
-{
- int err = -ENODEV;
-
- /* Probe for a specific ISA address */
- if (addr > 0xff && addr < 0x400)
- err = hp100_isa_probe1(dev, addr);
-
- else if (addr != 0)
- err = -ENXIO;
-
- else {
- /* Probe all ISA possible port regions */
- for (addr = 0x100; addr < 0x400; addr += 0x20) {
- err = hp100_isa_probe1(dev, addr);
- if (!err)
- break;
- }
- }
- return err;
-}
-#endif /* CONFIG_ISA */
-
-#if !defined(MODULE) && defined(CONFIG_ISA)
-struct net_device * __init hp100_probe(int unit)
-{
- struct net_device *dev = alloc_etherdev(sizeof(struct hp100_private));
- int err;
-
- if (!dev)
- return ERR_PTR(-ENODEV);
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4200, TRACE);
- printk("hp100: %s: probe\n", dev->name);
-#endif
-
- if (unit >= 0) {
- sprintf(dev->name, "eth%d", unit);
- netdev_boot_setup_check(dev);
- }
-
- err = hp100_isa_probe(dev, dev->base_addr);
- if (err)
- goto out;
-
- return dev;
- out:
- free_netdev(dev);
- return ERR_PTR(err);
-}
-#endif /* !MODULE && CONFIG_ISA */
-
-static const struct net_device_ops hp100_bm_netdev_ops = {
- .ndo_open = hp100_open,
- .ndo_stop = hp100_close,
- .ndo_start_xmit = hp100_start_xmit_bm,
- .ndo_get_stats = hp100_get_stats,
- .ndo_set_rx_mode = hp100_set_multicast_list,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_validate_addr = eth_validate_addr,
-};
-
-static const struct net_device_ops hp100_netdev_ops = {
- .ndo_open = hp100_open,
- .ndo_stop = hp100_close,
- .ndo_start_xmit = hp100_start_xmit,
- .ndo_get_stats = hp100_get_stats,
- .ndo_set_rx_mode = hp100_set_multicast_list,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_validate_addr = eth_validate_addr,
-};
-
-static int hp100_probe1(struct net_device *dev, int ioaddr, u_char bus,
- struct pci_dev *pci_dev)
-{
- int i;
- int err = -ENODEV;
- const char *eid;
- u_int chip;
- u_char uc;
- u_int memory_size = 0, virt_memory_size = 0;
- u_short local_mode, lsw;
- short mem_mapped;
- unsigned long mem_ptr_phys;
- void __iomem *mem_ptr_virt;
- struct hp100_private *lp;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4201, TRACE);
- printk("hp100: %s: probe1\n", dev->name);
-#endif
-
- /* memory region for programmed i/o */
- if (!request_region(ioaddr, HP100_REGION_SIZE, "hp100"))
- goto out1;
-
- if (hp100_inw(HW_ID) != HP100_HW_ID_CASCADE)
- goto out2;
-
- chip = hp100_inw(PAGING) & HP100_CHIPID_MASK;
-#ifdef HP100_DEBUG
- if (chip == HP100_CHIPID_SHASTA)
- printk("hp100: %s: Shasta Chip detected. (This is a pre 802.12 chip)\n", dev->name);
- else if (chip == HP100_CHIPID_RAINIER)
- printk("hp100: %s: Rainier Chip detected. (This is a pre 802.12 chip)\n", dev->name);
- else if (chip == HP100_CHIPID_LASSEN)
- printk("hp100: %s: Lassen Chip detected.\n", dev->name);
- else
- printk("hp100: %s: Warning: Unknown CASCADE chip (id=0x%.4x).\n", dev->name, chip);
-#endif
-
- dev->base_addr = ioaddr;
-
- eid = hp100_read_id(ioaddr);
- if (eid == NULL) { /* bad checksum? */
- netdev_warn(dev, "bad ID checksum at base port 0x%x\n",
- ioaddr);
- goto out2;
- }
-
- hp100_page(ID_MAC_ADDR);
- for (i = uc = 0; i < 7; i++)
- uc += hp100_inb(LAN_ADDR + i);
- if (uc != 0xff) {
- netdev_warn(dev,
- "bad lan address checksum at port 0x%x)\n",
- ioaddr);
- err = -EIO;
- goto out2;
- }
-
- /* Make sure, that all registers are correctly updated... */
-
- hp100_load_eeprom(dev, ioaddr);
- wait();
-
- /*
- * Determine driver operation mode
- *
- * Use the variable "hp100_mode" upon insmod or as kernel parameter to
- * force driver modes:
- * hp100_mode=1 -> default, use busmaster mode if configured.
- * hp100_mode=2 -> enable shared memory mode
- * hp100_mode=3 -> force use of i/o mapped mode.
- * hp100_mode=4 -> same as 1, but re-set the enable bit on the card.
- */
-
- /*
- * LSW values:
- * 0x2278 -> J2585B, PnP shared memory mode
- * 0x2270 -> J2585B, shared memory mode, 0xdc000
- * 0xa23c -> J2585B, I/O mapped mode
- * 0x2240 -> EISA COMPEX, BusMaster (Shasta Chip)
- * 0x2220 -> EISA HP, I/O (Shasta Chip)
- * 0x2260 -> EISA HP, BusMaster (Shasta Chip)
- */
-
- /* hp100_mode value maybe used in future by another card */
- local_mode = hp100_mode;
- if (local_mode < 1 || local_mode > 4)
- local_mode = 1; /* default */
-#ifdef HP100_DEBUG
- printk("hp100: %s: original LSW = 0x%x\n", dev->name,
- hp100_inw(OPTION_LSW));
-#endif
-
- if (local_mode == 3) {
- hp100_outw(HP100_MEM_EN | HP100_RESET_LB, OPTION_LSW);
- hp100_outw(HP100_IO_EN | HP100_SET_LB, OPTION_LSW);
- hp100_outw(HP100_BM_WRITE | HP100_BM_READ | HP100_RESET_HB, OPTION_LSW);
- printk("hp100: IO mapped mode forced.\n");
- } else if (local_mode == 2) {
- hp100_outw(HP100_MEM_EN | HP100_SET_LB, OPTION_LSW);
- hp100_outw(HP100_IO_EN | HP100_SET_LB, OPTION_LSW);
- hp100_outw(HP100_BM_WRITE | HP100_BM_READ | HP100_RESET_HB, OPTION_LSW);
- printk("hp100: Shared memory mode requested.\n");
- } else if (local_mode == 4) {
- if (chip == HP100_CHIPID_LASSEN) {
- hp100_outw(HP100_BM_WRITE | HP100_BM_READ | HP100_SET_HB, OPTION_LSW);
- hp100_outw(HP100_IO_EN | HP100_MEM_EN | HP100_RESET_LB, OPTION_LSW);
- printk("hp100: Busmaster mode requested.\n");
- }
- local_mode = 1;
- }
-
- if (local_mode == 1) { /* default behaviour */
- lsw = hp100_inw(OPTION_LSW);
-
- if ((lsw & HP100_IO_EN) && (~lsw & HP100_MEM_EN) &&
- (~lsw & (HP100_BM_WRITE | HP100_BM_READ))) {
-#ifdef HP100_DEBUG
- printk("hp100: %s: IO_EN bit is set on card.\n", dev->name);
-#endif
- local_mode = 3;
- } else if (chip == HP100_CHIPID_LASSEN &&
- (lsw & (HP100_BM_WRITE | HP100_BM_READ)) == (HP100_BM_WRITE | HP100_BM_READ)) {
- /* Conversion to new PCI API :
- * I don't have the doc, but I assume that the card
- * can map the full 32bit address space.
- * Also, we can have EISA Busmaster cards (not tested),
- * so beware !!! - Jean II */
- if ((bus == HP100_BUS_PCI) &&
- (pci_set_dma_mask(pci_dev, DMA_BIT_MASK(32)))) {
- /* Gracefully fallback to shared memory */
- goto busmasterfail;
- }
- printk("hp100: Busmaster mode enabled.\n");
- hp100_outw(HP100_MEM_EN | HP100_IO_EN | HP100_RESET_LB, OPTION_LSW);
- } else {
- busmasterfail:
-#ifdef HP100_DEBUG
- printk("hp100: %s: Card not configured for BM or BM not supported with this card.\n", dev->name);
- printk("hp100: %s: Trying shared memory mode.\n", dev->name);
-#endif
- /* In this case, try shared memory mode */
- local_mode = 2;
- hp100_outw(HP100_MEM_EN | HP100_SET_LB, OPTION_LSW);
- /* hp100_outw(HP100_IO_EN|HP100_RESET_LB, OPTION_LSW); */
- }
- }
-#ifdef HP100_DEBUG
- printk("hp100: %s: new LSW = 0x%x\n", dev->name, hp100_inw(OPTION_LSW));
-#endif
-
- /* Check for shared memory on the card, eventually remap it */
- hp100_page(HW_MAP);
- mem_mapped = ((hp100_inw(OPTION_LSW) & (HP100_MEM_EN)) != 0);
- mem_ptr_phys = 0UL;
- mem_ptr_virt = NULL;
- memory_size = (8192 << ((hp100_inb(SRAM) >> 5) & 0x07));
- virt_memory_size = 0;
-
- /* For memory mapped or busmaster mode, we want the memory address */
- if (mem_mapped || (local_mode == 1)) {
- mem_ptr_phys = (hp100_inw(MEM_MAP_LSW) | (hp100_inw(MEM_MAP_MSW) << 16));
- mem_ptr_phys &= ~0x1fff; /* 8k alignment */
-
- if (bus == HP100_BUS_ISA && (mem_ptr_phys & ~0xfffff) != 0) {
- printk("hp100: Can only use programmed i/o mode.\n");
- mem_ptr_phys = 0;
- mem_mapped = 0;
- local_mode = 3; /* Use programmed i/o */
- }
-
- /* We do not need access to shared memory in busmaster mode */
- /* However in slave mode we need to remap high (>1GB) card memory */
- if (local_mode != 1) { /* = not busmaster */
- /* We try with smaller memory sizes, if ioremap fails */
- for (virt_memory_size = memory_size; virt_memory_size > 16383; virt_memory_size >>= 1) {
- if ((mem_ptr_virt = ioremap((u_long) mem_ptr_phys, virt_memory_size)) == NULL) {
-#ifdef HP100_DEBUG
- printk("hp100: %s: ioremap for 0x%x bytes high PCI memory at 0x%lx failed\n", dev->name, virt_memory_size, mem_ptr_phys);
-#endif
- } else {
-#ifdef HP100_DEBUG
- printk("hp100: %s: remapped 0x%x bytes high PCI memory at 0x%lx to %p.\n", dev->name, virt_memory_size, mem_ptr_phys, mem_ptr_virt);
-#endif
- break;
- }
- }
-
- if (mem_ptr_virt == NULL) { /* all ioremap tries failed */
- printk("hp100: Failed to ioremap the PCI card memory. Will have to use i/o mapped mode.\n");
- local_mode = 3;
- virt_memory_size = 0;
- }
- }
- }
-
- if (local_mode == 3) { /* io mapped forced */
- mem_mapped = 0;
- mem_ptr_phys = 0;
- mem_ptr_virt = NULL;
- printk("hp100: Using (slow) programmed i/o mode.\n");
- }
-
- /* Initialise the "private" data structure for this card. */
- lp = netdev_priv(dev);
-
- spin_lock_init(&lp->lock);
- strlcpy(lp->id, eid, HP100_SIG_LEN);
- lp->chip = chip;
- lp->mode = local_mode;
- lp->bus = bus;
- lp->pci_dev = pci_dev;
- lp->priority_tx = hp100_priority_tx;
- lp->rx_ratio = hp100_rx_ratio;
- lp->mem_ptr_phys = mem_ptr_phys;
- lp->mem_ptr_virt = mem_ptr_virt;
- hp100_page(ID_MAC_ADDR);
- lp->soft_model = hp100_inb(SOFT_MODEL);
- lp->mac1_mode = HP100_MAC1MODE3;
- lp->mac2_mode = HP100_MAC2MODE3;
- memset(&lp->hash_bytes, 0x00, 8);
-
- dev->base_addr = ioaddr;
-
- lp->memory_size = memory_size;
- lp->virt_memory_size = virt_memory_size;
- lp->rx_ratio = hp100_rx_ratio; /* can be conf'd with insmod */
-
- if (lp->mode == 1) /* busmaster */
- dev->netdev_ops = &hp100_bm_netdev_ops;
- else
- dev->netdev_ops = &hp100_netdev_ops;
-
- /* Ask the card for which IRQ line it is configured */
- if (bus == HP100_BUS_PCI) {
- dev->irq = pci_dev->irq;
- } else {
- hp100_page(HW_MAP);
- dev->irq = hp100_inb(IRQ_CHANNEL) & HP100_IRQMASK;
- if (dev->irq == 2)
- dev->irq = 9;
- }
-
- if (lp->mode == 1) /* busmaster */
- dev->dma = 4;
-
- /* Ask the card for its MAC address and store it for later use. */
- hp100_page(ID_MAC_ADDR);
- for (i = uc = 0; i < 6; i++)
- dev->dev_addr[i] = hp100_inb(LAN_ADDR + i);
-
- /* Reset statistics (counters) */
- hp100_clear_stats(lp, ioaddr);
-
- /* If busmaster mode is wanted, a dma-capable memory area is needed for
- * the rx and tx PDLs
- * PCI cards can access the whole PC memory. Therefore GFP_DMA is not
- * needed for the allocation of the memory area.
- */
-
- /* TODO: We do not need this with old cards, where PDLs are stored
- * in the cards shared memory area. But currently, busmaster has been
- * implemented/tested only with the lassen chip anyway...
- */
- if (lp->mode == 1) { /* busmaster */
- dma_addr_t page_baddr;
- /* Get physically continuous memory for TX & RX PDLs */
- /* Conversion to new PCI API :
- * Pages are always aligned and zeroed, no need to it ourself.
- * Doc says should be OK for EISA bus as well - Jean II
- */
- lp->page_vaddr_algn = pci_alloc_consistent(lp->pci_dev, MAX_RINGSIZE, &page_baddr);
- if (!lp->page_vaddr_algn) {
- err = -ENOMEM;
- goto out_mem_ptr;
- }
- lp->whatever_offset = ((u_long) page_baddr) - ((u_long) lp->page_vaddr_algn);
-
-#ifdef HP100_DEBUG_BM
- printk("hp100: %s: Reserved DMA memory from 0x%x to 0x%x\n", dev->name, (u_int) lp->page_vaddr_algn, (u_int) lp->page_vaddr_algn + MAX_RINGSIZE);
-#endif
- lp->rxrcommit = lp->txrcommit = 0;
- lp->rxrhead = lp->rxrtail = &(lp->rxring[0]);
- lp->txrhead = lp->txrtail = &(lp->txring[0]);
- }
-
- /* Initialise the card. */
- /* (I'm not really sure if it's a good idea to do this during probing, but
- * like this it's assured that the lan connection type can be sensed
- * correctly)
- */
- hp100_hwinit(dev);
-
- /* Try to find out which kind of LAN the card is connected to. */
- lp->lan_type = hp100_sense_lan(dev);
-
- /* Print out a message what about what we think we have probed. */
- printk("hp100: at 0x%x, IRQ %d, ", ioaddr, dev->irq);
- switch (bus) {
- case HP100_BUS_EISA:
- printk("EISA");
- break;
- case HP100_BUS_PCI:
- printk("PCI");
- break;
- default:
- printk("ISA");
- break;
- }
- printk(" bus, %dk SRAM (rx/tx %d%%).\n", lp->memory_size >> 10, lp->rx_ratio);
-
- if (lp->mode == 2) { /* memory mapped */
- printk("hp100: Memory area at 0x%lx-0x%lx", mem_ptr_phys,
- (mem_ptr_phys + (mem_ptr_phys > 0x100000 ? (u_long) lp->memory_size : 16 * 1024)) - 1);
- if (mem_ptr_virt)
- printk(" (virtual base %p)", mem_ptr_virt);
- printk(".\n");
-
- /* Set for info when doing ifconfig */
- dev->mem_start = mem_ptr_phys;
- dev->mem_end = mem_ptr_phys + lp->memory_size;
- }
-
- printk("hp100: ");
- if (lp->lan_type != HP100_LAN_ERR)
- printk("Adapter is attached to ");
- switch (lp->lan_type) {
- case HP100_LAN_100:
- printk("100Mb/s Voice Grade AnyLAN network.\n");
- break;
- case HP100_LAN_10:
- printk("10Mb/s network (10baseT).\n");
- break;
- case HP100_LAN_COAX:
- printk("10Mb/s network (coax).\n");
- break;
- default:
- printk("Warning! Link down.\n");
- }
-
- err = register_netdev(dev);
- if (err)
- goto out3;
-
- return 0;
-out3:
- if (local_mode == 1)
- pci_free_consistent(lp->pci_dev, MAX_RINGSIZE + 0x0f,
- lp->page_vaddr_algn,
- virt_to_whatever(dev, lp->page_vaddr_algn));
-out_mem_ptr:
- if (mem_ptr_virt)
- iounmap(mem_ptr_virt);
-out2:
- release_region(ioaddr, HP100_REGION_SIZE);
-out1:
- return err;
-}
-
-/* This procedure puts the card into a stable init state */
-static void hp100_hwinit(struct net_device *dev)
-{
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4202, TRACE);
- printk("hp100: %s: hwinit\n", dev->name);
-#endif
-
- /* Initialise the card. -------------------------------------------- */
-
- /* Clear all pending Ints and disable Ints */
- hp100_page(PERFORMANCE);
- hp100_outw(0xfefe, IRQ_MASK); /* mask off all ints */
- hp100_outw(0xffff, IRQ_STATUS); /* clear all pending ints */
-
- hp100_outw(HP100_INT_EN | HP100_RESET_LB, OPTION_LSW);
- hp100_outw(HP100_TRI_INT | HP100_SET_HB, OPTION_LSW);
-
- if (lp->mode == 1) {
- hp100_BM_shutdown(dev); /* disables BM, puts cascade in reset */
- wait();
- } else {
- hp100_outw(HP100_INT_EN | HP100_RESET_LB, OPTION_LSW);
- hp100_cascade_reset(dev, 1);
- hp100_page(MAC_CTRL);
- hp100_andb(~(HP100_RX_EN | HP100_TX_EN), MAC_CFG_1);
- }
-
- /* Initiate EEPROM reload */
- hp100_load_eeprom(dev, 0);
-
- wait();
-
- /* Go into reset again. */
- hp100_cascade_reset(dev, 1);
-
- /* Set Option Registers to a safe state */
- hp100_outw(HP100_DEBUG_EN |
- HP100_RX_HDR |
- HP100_EE_EN |
- HP100_BM_WRITE |
- HP100_BM_READ | HP100_RESET_HB |
- HP100_FAKE_INT |
- HP100_INT_EN |
- HP100_MEM_EN |
- HP100_IO_EN | HP100_RESET_LB, OPTION_LSW);
-
- hp100_outw(HP100_TRI_INT |
- HP100_MMAP_DIS | HP100_SET_HB, OPTION_LSW);
-
- hp100_outb(HP100_PRIORITY_TX |
- HP100_ADV_NXT_PKT |
- HP100_TX_CMD | HP100_RESET_LB, OPTION_MSW);
-
- /* TODO: Configure MMU for Ram Test. */
- /* TODO: Ram Test. */
-
- /* Re-check if adapter is still at same i/o location */
- /* (If the base i/o in eeprom has been changed but the */
- /* registers had not been changed, a reload of the eeprom */
- /* would move the adapter to the address stored in eeprom */
-
- /* TODO: Code to implement. */
-
- /* Until here it was code from HWdiscover procedure. */
- /* Next comes code from mmuinit procedure of SCO BM driver which is
- * called from HWconfigure in the SCO driver.
- */
-
- /* Initialise MMU, eventually switch on Busmaster Mode, initialise
- * multicast filter...
- */
- hp100_mmuinit(dev);
-
- /* We don't turn the interrupts on here - this is done by start_interface. */
- wait(); /* TODO: Do we really need this? */
-
- /* Enable Hardware (e.g. unreset) */
- hp100_cascade_reset(dev, 0);
-
- /* ------- initialisation complete ----------- */
-
- /* Finally try to log in the Hub if there may be a VG connection. */
- if ((lp->lan_type == HP100_LAN_100) || (lp->lan_type == HP100_LAN_ERR))
- hp100_login_to_vg_hub(dev, 0); /* relogin */
-}
-
-/*
- * mmuinit - Reinitialise Cascade MMU and MAC settings.
- * Note: Must already be in reset and leaves card in reset.
- */
-static void hp100_mmuinit(struct net_device *dev)
-{
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
- int i;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4203, TRACE);
- printk("hp100: %s: mmuinit\n", dev->name);
-#endif
-
-#ifdef HP100_DEBUG
- if (0 != (hp100_inw(OPTION_LSW) & HP100_HW_RST)) {
- printk("hp100: %s: Not in reset when entering mmuinit. Fix me.\n", dev->name);
- return;
- }
-#endif
-
- /* Make sure IRQs are masked off and ack'ed. */
- hp100_page(PERFORMANCE);
- hp100_outw(0xfefe, IRQ_MASK); /* mask off all ints */
- hp100_outw(0xffff, IRQ_STATUS); /* ack IRQ */
-
- /*
- * Enable Hardware
- * - Clear Debug En, Rx Hdr Pipe, EE En, I/O En, Fake Int and Intr En
- * - Set Tri-State Int, Bus Master Rd/Wr, and Mem Map Disable
- * - Clear Priority, Advance Pkt and Xmit Cmd
- */
-
- hp100_outw(HP100_DEBUG_EN |
- HP100_RX_HDR |
- HP100_EE_EN | HP100_RESET_HB |
- HP100_IO_EN |
- HP100_FAKE_INT |
- HP100_INT_EN | HP100_RESET_LB, OPTION_LSW);
-
- hp100_outw(HP100_TRI_INT | HP100_SET_HB, OPTION_LSW);
-
- if (lp->mode == 1) { /* busmaster */
- hp100_outw(HP100_BM_WRITE |
- HP100_BM_READ |
- HP100_MMAP_DIS | HP100_SET_HB, OPTION_LSW);
- } else if (lp->mode == 2) { /* memory mapped */
- hp100_outw(HP100_BM_WRITE |
- HP100_BM_READ | HP100_RESET_HB, OPTION_LSW);
- hp100_outw(HP100_MMAP_DIS | HP100_RESET_HB, OPTION_LSW);
- hp100_outw(HP100_MEM_EN | HP100_SET_LB, OPTION_LSW);
- hp100_outw(HP100_IO_EN | HP100_SET_LB, OPTION_LSW);
- } else if (lp->mode == 3) { /* i/o mapped mode */
- hp100_outw(HP100_MMAP_DIS | HP100_SET_HB |
- HP100_IO_EN | HP100_SET_LB, OPTION_LSW);
- }
-
- hp100_page(HW_MAP);
- hp100_outb(0, EARLYRXCFG);
- hp100_outw(0, EARLYTXCFG);
-
- /*
- * Enable Bus Master mode
- */
- if (lp->mode == 1) { /* busmaster */
- /* Experimental: Set some PCI configuration bits */
- hp100_page(HW_MAP);
- hp100_andb(~HP100_PDL_USE3, MODECTRL1); /* BM engine read maximum */
- hp100_andb(~HP100_TX_DUALQ, MODECTRL1); /* No Queue for Priority TX */
-
- /* PCI Bus failures should result in a Misc. Interrupt */
- hp100_orb(HP100_EN_BUS_FAIL, MODECTRL2);
-
- hp100_outw(HP100_BM_READ | HP100_BM_WRITE | HP100_SET_HB, OPTION_LSW);
- hp100_page(HW_MAP);
- /* Use Burst Mode and switch on PAGE_CK */
- hp100_orb(HP100_BM_BURST_RD | HP100_BM_BURST_WR, BM);
- if ((lp->chip == HP100_CHIPID_RAINIER) || (lp->chip == HP100_CHIPID_SHASTA))
- hp100_orb(HP100_BM_PAGE_CK, BM);
- hp100_orb(HP100_BM_MASTER, BM);
- } else { /* not busmaster */
-
- hp100_page(HW_MAP);
- hp100_andb(~HP100_BM_MASTER, BM);
- }
-
- /*
- * Divide card memory into regions for Rx, Tx and, if non-ETR chip, PDLs
- */
- hp100_page(MMU_CFG);
- if (lp->mode == 1) { /* only needed for Busmaster */
- int xmit_stop, recv_stop;
-
- if ((lp->chip == HP100_CHIPID_RAINIER) ||
- (lp->chip == HP100_CHIPID_SHASTA)) {
- int pdl_stop;
-
- /*
- * Each pdl is 508 bytes long. (63 frags * 4 bytes for address and
- * 4 bytes for header). We will leave NUM_RXPDLS * 508 (rounded
- * to the next higher 1k boundary) bytes for the rx-pdl's
- * Note: For non-etr chips the transmit stop register must be
- * programmed on a 1k boundary, i.e. bits 9:0 must be zero.
- */
- pdl_stop = lp->memory_size;
- xmit_stop = (pdl_stop - 508 * (MAX_RX_PDL) - 16) & ~(0x03ff);
- recv_stop = (xmit_stop * (lp->rx_ratio) / 100) & ~(0x03ff);
- hp100_outw((pdl_stop >> 4) - 1, PDL_MEM_STOP);
-#ifdef HP100_DEBUG_BM
- printk("hp100: %s: PDL_STOP = 0x%x\n", dev->name, pdl_stop);
-#endif
- } else {
- /* ETR chip (Lassen) in busmaster mode */
- xmit_stop = (lp->memory_size) - 1;
- recv_stop = ((lp->memory_size * lp->rx_ratio) / 100) & ~(0x03ff);
- }
-
- hp100_outw(xmit_stop >> 4, TX_MEM_STOP);
- hp100_outw(recv_stop >> 4, RX_MEM_STOP);
-#ifdef HP100_DEBUG_BM
- printk("hp100: %s: TX_STOP = 0x%x\n", dev->name, xmit_stop >> 4);
- printk("hp100: %s: RX_STOP = 0x%x\n", dev->name, recv_stop >> 4);
-#endif
- } else {
- /* Slave modes (memory mapped and programmed io) */
- hp100_outw((((lp->memory_size * lp->rx_ratio) / 100) >> 4), RX_MEM_STOP);
- hp100_outw(((lp->memory_size - 1) >> 4), TX_MEM_STOP);
-#ifdef HP100_DEBUG
- printk("hp100: %s: TX_MEM_STOP: 0x%x\n", dev->name, hp100_inw(TX_MEM_STOP));
- printk("hp100: %s: RX_MEM_STOP: 0x%x\n", dev->name, hp100_inw(RX_MEM_STOP));
-#endif
- }
-
- /* Write MAC address into page 1 */
- hp100_page(MAC_ADDRESS);
- for (i = 0; i < 6; i++)
- hp100_outb(dev->dev_addr[i], MAC_ADDR + i);
-
- /* Zero the multicast hash registers */
- for (i = 0; i < 8; i++)
- hp100_outb(0x0, HASH_BYTE0 + i);
-
- /* Set up MAC defaults */
- hp100_page(MAC_CTRL);
-
- /* Go to LAN Page and zero all filter bits */
- /* Zero accept error, accept multicast, accept broadcast and accept */
- /* all directed packet bits */
- hp100_andb(~(HP100_RX_EN |
- HP100_TX_EN |
- HP100_ACC_ERRORED |
- HP100_ACC_MC |
- HP100_ACC_BC | HP100_ACC_PHY), MAC_CFG_1);
-
- hp100_outb(0x00, MAC_CFG_2);
-
- /* Zero the frame format bit. This works around a training bug in the */
- /* new hubs. */
- hp100_outb(0x00, VG_LAN_CFG_2); /* (use 802.3) */
-
- if (lp->priority_tx)
- hp100_outb(HP100_PRIORITY_TX | HP100_SET_LB, OPTION_MSW);
- else
- hp100_outb(HP100_PRIORITY_TX | HP100_RESET_LB, OPTION_MSW);
-
- hp100_outb(HP100_ADV_NXT_PKT |
- HP100_TX_CMD | HP100_RESET_LB, OPTION_MSW);
-
- /* If busmaster, initialize the PDLs */
- if (lp->mode == 1)
- hp100_init_pdls(dev);
-
- /* Go to performance page and initialize isr and imr registers */
- hp100_page(PERFORMANCE);
- hp100_outw(0xfefe, IRQ_MASK); /* mask off all ints */
- hp100_outw(0xffff, IRQ_STATUS); /* ack IRQ */
-}
-
-/*
- * open/close functions
- */
-
-static int hp100_open(struct net_device *dev)
-{
- struct hp100_private *lp = netdev_priv(dev);
-#ifdef HP100_DEBUG_B
- int ioaddr = dev->base_addr;
-#endif
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4204, TRACE);
- printk("hp100: %s: open\n", dev->name);
-#endif
-
- /* New: if bus is PCI or EISA, interrupts might be shared interrupts */
- if (request_irq(dev->irq, hp100_interrupt,
- lp->bus == HP100_BUS_PCI || lp->bus ==
- HP100_BUS_EISA ? IRQF_SHARED : 0,
- dev->name, dev)) {
- printk("hp100: %s: unable to get IRQ %d\n", dev->name, dev->irq);
- return -EAGAIN;
- }
-
- netif_trans_update(dev); /* prevent tx timeout */
- netif_start_queue(dev);
-
- lp->lan_type = hp100_sense_lan(dev);
- lp->mac1_mode = HP100_MAC1MODE3;
- lp->mac2_mode = HP100_MAC2MODE3;
- memset(&lp->hash_bytes, 0x00, 8);
-
- hp100_stop_interface(dev);
-
- hp100_hwinit(dev);
-
- hp100_start_interface(dev); /* sets mac modes, enables interrupts */
-
- return 0;
-}
-
-/* The close function is called when the interface is to be brought down */
-static int hp100_close(struct net_device *dev)
-{
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4205, TRACE);
- printk("hp100: %s: close\n", dev->name);
-#endif
-
- hp100_page(PERFORMANCE);
- hp100_outw(0xfefe, IRQ_MASK); /* mask off all IRQs */
-
- hp100_stop_interface(dev);
-
- if (lp->lan_type == HP100_LAN_100)
- lp->hub_status = hp100_login_to_vg_hub(dev, 0);
-
- netif_stop_queue(dev);
-
- free_irq(dev->irq, dev);
-
-#ifdef HP100_DEBUG
- printk("hp100: %s: close LSW = 0x%x\n", dev->name,
- hp100_inw(OPTION_LSW));
-#endif
-
- return 0;
-}
-
-/*
- * Configure the PDL Rx rings and LAN
- */
-static void hp100_init_pdls(struct net_device *dev)
-{
- struct hp100_private *lp = netdev_priv(dev);
- hp100_ring_t *ringptr;
- u_int *pageptr; /* Warning : increment by 4 - Jean II */
- int i;
-
-#ifdef HP100_DEBUG_B
- int ioaddr = dev->base_addr;
-#endif
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4206, TRACE);
- printk("hp100: %s: init pdls\n", dev->name);
-#endif
-
- if (!lp->page_vaddr_algn)
- printk("hp100: %s: Warning: lp->page_vaddr_algn not initialised!\n", dev->name);
- else {
- /* pageptr shall point into the DMA accessible memory region */
- /* we use this pointer to status the upper limit of allocated */
- /* memory in the allocated page. */
- /* note: align the pointers to the pci cache line size */
- memset(lp->page_vaddr_algn, 0, MAX_RINGSIZE); /* Zero Rx/Tx ring page */
- pageptr = lp->page_vaddr_algn;
-
- lp->rxrcommit = 0;
- ringptr = lp->rxrhead = lp->rxrtail = &(lp->rxring[0]);
-
- /* Initialise Rx Ring */
- for (i = MAX_RX_PDL - 1; i >= 0; i--) {
- lp->rxring[i].next = ringptr;
- ringptr = &(lp->rxring[i]);
- pageptr += hp100_init_rxpdl(dev, ringptr, pageptr);
- }
-
- /* Initialise Tx Ring */
- lp->txrcommit = 0;
- ringptr = lp->txrhead = lp->txrtail = &(lp->txring[0]);
- for (i = MAX_TX_PDL - 1; i >= 0; i--) {
- lp->txring[i].next = ringptr;
- ringptr = &(lp->txring[i]);
- pageptr += hp100_init_txpdl(dev, ringptr, pageptr);
- }
- }
-}
-
-/* These functions "format" the entries in the pdl structure */
-/* They return how much memory the fragments need. */
-static int hp100_init_rxpdl(struct net_device *dev,
- register hp100_ring_t * ringptr,
- register u32 * pdlptr)
-{
- /* pdlptr is starting address for this pdl */
-
- if (0 != (((unsigned long) pdlptr) & 0xf))
- printk("hp100: %s: Init rxpdl: Unaligned pdlptr 0x%lx.\n",
- dev->name, (unsigned long) pdlptr);
-
- ringptr->pdl = pdlptr + 1;
- ringptr->pdl_paddr = virt_to_whatever(dev, pdlptr + 1);
- ringptr->skb = NULL;
-
- /*
- * Write address and length of first PDL Fragment (which is used for
- * storing the RX-Header
- * We use the 4 bytes _before_ the PDH in the pdl memory area to
- * store this information. (PDH is at offset 0x04)
- */
- /* Note that pdlptr+1 and not pdlptr is the pointer to the PDH */
-
- *(pdlptr + 2) = (u_int) virt_to_whatever(dev, pdlptr); /* Address Frag 1 */
- *(pdlptr + 3) = 4; /* Length Frag 1 */
-
- return roundup(MAX_RX_FRAG * 2 + 2, 4);
-}
-
-static int hp100_init_txpdl(struct net_device *dev,
- register hp100_ring_t * ringptr,
- register u32 * pdlptr)
-{
- if (0 != (((unsigned long) pdlptr) & 0xf))
- printk("hp100: %s: Init txpdl: Unaligned pdlptr 0x%lx.\n", dev->name, (unsigned long) pdlptr);
-
- ringptr->pdl = pdlptr; /* +1; */
- ringptr->pdl_paddr = virt_to_whatever(dev, pdlptr); /* +1 */
- ringptr->skb = NULL;
-
- return roundup(MAX_TX_FRAG * 2 + 2, 4);
-}
-
-/*
- * hp100_build_rx_pdl allocates an skb_buff of maximum size plus two bytes
- * for possible odd word alignment rounding up to next dword and set PDL
- * address for fragment#2
- * Returns: 0 if unable to allocate skb_buff
- * 1 if successful
- */
-static int hp100_build_rx_pdl(hp100_ring_t * ringptr,
- struct net_device *dev)
-{
-#ifdef HP100_DEBUG_B
- int ioaddr = dev->base_addr;
-#endif
-#ifdef HP100_DEBUG_BM
- u_int *p;
-#endif
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4207, TRACE);
- printk("hp100: %s: build rx pdl\n", dev->name);
-#endif
-
- /* Allocate skb buffer of maximum size */
- /* Note: This depends on the alloc_skb functions allocating more
- * space than requested, i.e. aligning to 16bytes
- */
-
- ringptr->skb = netdev_alloc_skb(dev, roundup(MAX_ETHER_SIZE + 2, 4));
-
- if (NULL != ringptr->skb) {
- /*
- * Reserve 2 bytes at the head of the buffer to land the IP header
- * on a long word boundary (According to the Network Driver section
- * in the Linux KHG, this should help to increase performance.)
- */
- skb_reserve(ringptr->skb, 2);
-
- ringptr->skb->data = skb_put(ringptr->skb, MAX_ETHER_SIZE);
-
- /* ringptr->pdl points to the beginning of the PDL, i.e. the PDH */
- /* Note: 1st Fragment is used for the 4 byte packet status
- * (receive header). Its PDL entries are set up by init_rxpdl. So
- * here we only have to set up the PDL fragment entries for the data
- * part. Those 4 bytes will be stored in the DMA memory region
- * directly before the PDL.
- */
-#ifdef HP100_DEBUG_BM
- printk("hp100: %s: build_rx_pdl: PDH@0x%x, skb->data (len %d) at 0x%x\n",
- dev->name, (u_int) ringptr->pdl,
- roundup(MAX_ETHER_SIZE + 2, 4),
- (unsigned int) ringptr->skb->data);
-#endif
-
- /* Conversion to new PCI API : map skbuf data to PCI bus.
- * Doc says it's OK for EISA as well - Jean II
- */
- ringptr->pdl[0] = 0x00020000; /* Write PDH */
- ringptr->pdl[3] = pdl_map_data(netdev_priv(dev),
- ringptr->skb->data);
- ringptr->pdl[4] = MAX_ETHER_SIZE; /* Length of Data */
-
-#ifdef HP100_DEBUG_BM
- for (p = (ringptr->pdl); p < (ringptr->pdl + 5); p++)
- printk("hp100: %s: Adr 0x%.8x = 0x%.8x\n", dev->name, (u_int) p, (u_int) * p);
-#endif
- return 1;
- }
- /* else: */
- /* alloc_skb failed (no memory) -> still can receive the header
- * fragment into PDL memory. make PDL safe by clearing msgptr and
- * making the PDL only 1 fragment (i.e. the 4 byte packet status)
- */
-#ifdef HP100_DEBUG_BM
- printk("hp100: %s: build_rx_pdl: PDH@0x%x, No space for skb.\n", dev->name, (u_int) ringptr->pdl);
-#endif
-
- ringptr->pdl[0] = 0x00010000; /* PDH: Count=1 Fragment */
-
- return 0;
-}
-
-/*
- * hp100_rxfill - attempt to fill the Rx Ring will empty skb's
- *
- * Makes assumption that skb's are always contiguous memory areas and
- * therefore PDLs contain only 2 physical fragments.
- * - While the number of Rx PDLs with buffers is less than maximum
- * a. Get a maximum packet size skb
- * b. Put the physical address of the buffer into the PDL.
- * c. Output physical address of PDL to adapter.
- */
-static void hp100_rxfill(struct net_device *dev)
-{
- int ioaddr = dev->base_addr;
-
- struct hp100_private *lp = netdev_priv(dev);
- hp100_ring_t *ringptr;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4208, TRACE);
- printk("hp100: %s: rxfill\n", dev->name);
-#endif
-
- hp100_page(PERFORMANCE);
-
- while (lp->rxrcommit < MAX_RX_PDL) {
- /*
- * Attempt to get a buffer and build a Rx PDL.
- */
- ringptr = lp->rxrtail;
- if (0 == hp100_build_rx_pdl(ringptr, dev)) {
- return; /* None available, return */
- }
-
- /* Hand this PDL over to the card */
- /* Note: This needs performance page selected! */
-#ifdef HP100_DEBUG_BM
- printk("hp100: %s: rxfill: Hand to card: pdl #%d @0x%x phys:0x%x, buffer: 0x%x\n",
- dev->name, lp->rxrcommit, (u_int) ringptr->pdl,
- (u_int) ringptr->pdl_paddr, (u_int) ringptr->pdl[3]);
-#endif
-
- hp100_outl((u32) ringptr->pdl_paddr, RX_PDA);
-
- lp->rxrcommit += 1;
- lp->rxrtail = ringptr->next;
- }
-}
-
-/*
- * BM_shutdown - shutdown bus mastering and leave chip in reset state
- */
-
-static void hp100_BM_shutdown(struct net_device *dev)
-{
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
- unsigned long time;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4209, TRACE);
- printk("hp100: %s: bm shutdown\n", dev->name);
-#endif
-
- hp100_page(PERFORMANCE);
- hp100_outw(0xfefe, IRQ_MASK); /* mask off all ints */
- hp100_outw(0xffff, IRQ_STATUS); /* Ack all ints */
-
- /* Ensure Interrupts are off */
- hp100_outw(HP100_INT_EN | HP100_RESET_LB, OPTION_LSW);
-
- /* Disable all MAC activity */
- hp100_page(MAC_CTRL);
- hp100_andb(~(HP100_RX_EN | HP100_TX_EN), MAC_CFG_1); /* stop rx/tx */
-
- /* If cascade MMU is not already in reset */
- if (0 != (hp100_inw(OPTION_LSW) & HP100_HW_RST)) {
- /* Wait 1.3ms (10Mb max packet time) to ensure MAC is idle so
- * MMU pointers will not be reset out from underneath
- */
- hp100_page(MAC_CTRL);
- for (time = 0; time < 5000; time++) {
- if ((hp100_inb(MAC_CFG_1) & (HP100_TX_IDLE | HP100_RX_IDLE)) == (HP100_TX_IDLE | HP100_RX_IDLE))
- break;
- }
-
- /* Shutdown algorithm depends on the generation of Cascade */
- if (lp->chip == HP100_CHIPID_LASSEN) { /* ETR shutdown/reset */
- /* Disable Busmaster mode and wait for bit to go to zero. */
- hp100_page(HW_MAP);
- hp100_andb(~HP100_BM_MASTER, BM);
- /* 100 ms timeout */
- for (time = 0; time < 32000; time++) {
- if (0 == (hp100_inb(BM) & HP100_BM_MASTER))
- break;
- }
- } else { /* Shasta or Rainier Shutdown/Reset */
- /* To ensure all bus master inloading activity has ceased,
- * wait for no Rx PDAs or no Rx packets on card.
- */
- hp100_page(PERFORMANCE);
- /* 100 ms timeout */
- for (time = 0; time < 10000; time++) {
- /* RX_PDL: PDLs not executed. */
- /* RX_PKT_CNT: RX'd packets on card. */
- if ((hp100_inb(RX_PDL) == 0) && (hp100_inb(RX_PKT_CNT) == 0))
- break;
- }
-
- if (time >= 10000)
- printk("hp100: %s: BM shutdown error.\n", dev->name);
-
- /* To ensure all bus master outloading activity has ceased,
- * wait until the Tx PDA count goes to zero or no more Tx space
- * available in the Tx region of the card.
- */
- /* 100 ms timeout */
- for (time = 0; time < 10000; time++) {
- if ((0 == hp100_inb(TX_PKT_CNT)) &&
- (0 != (hp100_inb(TX_MEM_FREE) & HP100_AUTO_COMPARE)))
- break;
- }
-
- /* Disable Busmaster mode */
- hp100_page(HW_MAP);
- hp100_andb(~HP100_BM_MASTER, BM);
- } /* end of shutdown procedure for non-etr parts */
-
- hp100_cascade_reset(dev, 1);
- }
- hp100_page(PERFORMANCE);
- /* hp100_outw( HP100_BM_READ | HP100_BM_WRITE | HP100_RESET_HB, OPTION_LSW ); */
- /* Busmaster mode should be shut down now. */
-}
-
-static int hp100_check_lan(struct net_device *dev)
-{
- struct hp100_private *lp = netdev_priv(dev);
-
- if (lp->lan_type < 0) { /* no LAN type detected yet? */
- hp100_stop_interface(dev);
- if ((lp->lan_type = hp100_sense_lan(dev)) < 0) {
- printk("hp100: %s: no connection found - check wire\n", dev->name);
- hp100_start_interface(dev); /* 10Mb/s RX packets maybe handled */
- return -EIO;
- }
- if (lp->lan_type == HP100_LAN_100)
- lp->hub_status = hp100_login_to_vg_hub(dev, 0); /* relogin */
- hp100_start_interface(dev);
- }
- return 0;
-}
-
-/*
- * transmit functions
- */
-
-/* tx function for busmaster mode */
-static netdev_tx_t hp100_start_xmit_bm(struct sk_buff *skb,
- struct net_device *dev)
-{
- unsigned long flags;
- int i, ok_flag;
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
- hp100_ring_t *ringptr;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4210, TRACE);
- printk("hp100: %s: start_xmit_bm\n", dev->name);
-#endif
- if (skb->len <= 0)
- goto drop;
-
- if (lp->chip == HP100_CHIPID_SHASTA && skb_padto(skb, ETH_ZLEN))
- return NETDEV_TX_OK;
-
- /* Get Tx ring tail pointer */
- if (lp->txrtail->next == lp->txrhead) {
- /* No memory. */
-#ifdef HP100_DEBUG
- printk("hp100: %s: start_xmit_bm: No TX PDL available.\n", dev->name);
-#endif
- /* not waited long enough since last tx? */
- if (time_before(jiffies, dev_trans_start(dev) + HZ))
- goto drop;
-
- if (hp100_check_lan(dev))
- goto drop;
-
- if (lp->lan_type == HP100_LAN_100 && lp->hub_status < 0) {
- /* we have a 100Mb/s adapter but it isn't connected to hub */
- printk("hp100: %s: login to 100Mb/s hub retry\n", dev->name);
- hp100_stop_interface(dev);
- lp->hub_status = hp100_login_to_vg_hub(dev, 0);
- hp100_start_interface(dev);
- } else {
- spin_lock_irqsave(&lp->lock, flags);
- hp100_ints_off(); /* Useful ? Jean II */
- i = hp100_sense_lan(dev);
- hp100_ints_on();
- spin_unlock_irqrestore(&lp->lock, flags);
- if (i == HP100_LAN_ERR)
- printk("hp100: %s: link down detected\n", dev->name);
- else if (lp->lan_type != i) { /* cable change! */
- /* it's very hard - all network settings must be changed!!! */
- printk("hp100: %s: cable change 10Mb/s <-> 100Mb/s detected\n", dev->name);
- lp->lan_type = i;
- hp100_stop_interface(dev);
- if (lp->lan_type == HP100_LAN_100)
- lp->hub_status = hp100_login_to_vg_hub(dev, 0);
- hp100_start_interface(dev);
- } else {
- printk("hp100: %s: interface reset\n", dev->name);
- hp100_stop_interface(dev);
- if (lp->lan_type == HP100_LAN_100)
- lp->hub_status = hp100_login_to_vg_hub(dev, 0);
- hp100_start_interface(dev);
- }
- }
-
- goto drop;
- }
-
- /*
- * we have to turn int's off before modifying this, otherwise
- * a tx_pdl_cleanup could occur at the same time
- */
- spin_lock_irqsave(&lp->lock, flags);
- ringptr = lp->txrtail;
- lp->txrtail = ringptr->next;
-
- /* Check whether packet has minimal packet size */
- ok_flag = skb->len >= HP100_MIN_PACKET_SIZE;
- i = ok_flag ? skb->len : HP100_MIN_PACKET_SIZE;
-
- ringptr->skb = skb;
- ringptr->pdl[0] = ((1 << 16) | i); /* PDH: 1 Fragment & length */
- if (lp->chip == HP100_CHIPID_SHASTA) {
- /* TODO:Could someone who has the EISA card please check if this works? */
- ringptr->pdl[2] = i;
- } else { /* Lassen */
- /* In the PDL, don't use the padded size but the real packet size: */
- ringptr->pdl[2] = skb->len; /* 1st Frag: Length of frag */
- }
- /* Conversion to new PCI API : map skbuf data to PCI bus.
- * Doc says it's OK for EISA as well - Jean II
- */
- ringptr->pdl[1] = ((u32) pci_map_single(lp->pci_dev, skb->data, ringptr->pdl[2], PCI_DMA_TODEVICE)); /* 1st Frag: Adr. of data */
-
- /* Hand this PDL to the card. */
- hp100_outl(ringptr->pdl_paddr, TX_PDA_L); /* Low Prio. Queue */
-
- lp->txrcommit++;
-
- dev->stats.tx_packets++;
- dev->stats.tx_bytes += skb->len;
-
- spin_unlock_irqrestore(&lp->lock, flags);
-
- return NETDEV_TX_OK;
-
-drop:
- dev_kfree_skb(skb);
- return NETDEV_TX_OK;
-}
-
-/* clean_txring checks if packets have been sent by the card by reading
- * the TX_PDL register from the performance page and comparing it to the
- * number of committed packets. It then frees the skb's of the packets that
- * obviously have been sent to the network.
- *
- * Needs the PERFORMANCE page selected.
- */
-static void hp100_clean_txring(struct net_device *dev)
-{
- struct hp100_private *lp = netdev_priv(dev);
- int ioaddr = dev->base_addr;
- int donecount;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4211, TRACE);
- printk("hp100: %s: clean txring\n", dev->name);
-#endif
-
- /* How many PDLs have been transmitted? */
- donecount = (lp->txrcommit) - hp100_inb(TX_PDL);
-
-#ifdef HP100_DEBUG
- if (donecount > MAX_TX_PDL)
- printk("hp100: %s: Warning: More PDLs transmitted than committed to card???\n", dev->name);
-#endif
-
- for (; 0 != donecount; donecount--) {
-#ifdef HP100_DEBUG_BM
- printk("hp100: %s: Free skb: data @0x%.8x txrcommit=0x%x TXPDL=0x%x, done=0x%x\n",
- dev->name, (u_int) lp->txrhead->skb->data,
- lp->txrcommit, hp100_inb(TX_PDL), donecount);
-#endif
- /* Conversion to new PCI API : NOP */
- pci_unmap_single(lp->pci_dev, (dma_addr_t) lp->txrhead->pdl[1], lp->txrhead->pdl[2], PCI_DMA_TODEVICE);
- dev_consume_skb_any(lp->txrhead->skb);
- lp->txrhead->skb = NULL;
- lp->txrhead = lp->txrhead->next;
- lp->txrcommit--;
- }
-}
-
-/* tx function for slave modes */
-static netdev_tx_t hp100_start_xmit(struct sk_buff *skb,
- struct net_device *dev)
-{
- unsigned long flags;
- int i, ok_flag;
- int ioaddr = dev->base_addr;
- u_short val;
- struct hp100_private *lp = netdev_priv(dev);
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4212, TRACE);
- printk("hp100: %s: start_xmit\n", dev->name);
-#endif
- if (skb->len <= 0)
- goto drop;
-
- if (hp100_check_lan(dev))
- goto drop;
-
- /* If there is not enough free memory on the card... */
- i = hp100_inl(TX_MEM_FREE) & 0x7fffffff;
- if (!(((i / 2) - 539) > (skb->len + 16) && (hp100_inb(TX_PKT_CNT) < 255))) {
-#ifdef HP100_DEBUG
- printk("hp100: %s: start_xmit: tx free mem = 0x%x\n", dev->name, i);
-#endif
- /* not waited long enough since last failed tx try? */
- if (time_before(jiffies, dev_trans_start(dev) + HZ)) {
-#ifdef HP100_DEBUG
- printk("hp100: %s: trans_start timing problem\n",
- dev->name);
-#endif
- goto drop;
- }
- if (lp->lan_type == HP100_LAN_100 && lp->hub_status < 0) {
- /* we have a 100Mb/s adapter but it isn't connected to hub */
- printk("hp100: %s: login to 100Mb/s hub retry\n", dev->name);
- hp100_stop_interface(dev);
- lp->hub_status = hp100_login_to_vg_hub(dev, 0);
- hp100_start_interface(dev);
- } else {
- spin_lock_irqsave(&lp->lock, flags);
- hp100_ints_off(); /* Useful ? Jean II */
- i = hp100_sense_lan(dev);
- hp100_ints_on();
- spin_unlock_irqrestore(&lp->lock, flags);
- if (i == HP100_LAN_ERR)
- printk("hp100: %s: link down detected\n", dev->name);
- else if (lp->lan_type != i) { /* cable change! */
- /* it's very hard - all network setting must be changed!!! */
- printk("hp100: %s: cable change 10Mb/s <-> 100Mb/s detected\n", dev->name);
- lp->lan_type = i;
- hp100_stop_interface(dev);
- if (lp->lan_type == HP100_LAN_100)
- lp->hub_status = hp100_login_to_vg_hub(dev, 0);
- hp100_start_interface(dev);
- } else {
- printk("hp100: %s: interface reset\n", dev->name);
- hp100_stop_interface(dev);
- if (lp->lan_type == HP100_LAN_100)
- lp->hub_status = hp100_login_to_vg_hub(dev, 0);
- hp100_start_interface(dev);
- mdelay(1);
- }
- }
- goto drop;
- }
-
- for (i = 0; i < 6000 && (hp100_inb(OPTION_MSW) & HP100_TX_CMD); i++) {
-#ifdef HP100_DEBUG_TX
- printk("hp100: %s: start_xmit: busy\n", dev->name);
-#endif
- }
-
- spin_lock_irqsave(&lp->lock, flags);
- hp100_ints_off();
- val = hp100_inw(IRQ_STATUS);
- /* Ack / clear the interrupt TX_COMPLETE interrupt - this interrupt is set
- * when the current packet being transmitted on the wire is completed.
- */
- hp100_outw(HP100_TX_COMPLETE, IRQ_STATUS);
-#ifdef HP100_DEBUG_TX
- printk("hp100: %s: start_xmit: irq_status=0x%.4x, irqmask=0x%.4x, len=%d\n",
- dev->name, val, hp100_inw(IRQ_MASK), (int) skb->len);
-#endif
-
- ok_flag = skb->len >= HP100_MIN_PACKET_SIZE;
- i = ok_flag ? skb->len : HP100_MIN_PACKET_SIZE;
-
- hp100_outw(i, DATA32); /* tell card the total packet length */
- hp100_outw(i, FRAGMENT_LEN); /* and first/only fragment length */
-
- if (lp->mode == 2) { /* memory mapped */
- /* Note: The J2585B needs alignment to 32bits here! */
- memcpy_toio(lp->mem_ptr_virt, skb->data, (skb->len + 3) & ~3);
- if (!ok_flag)
- memset_io(lp->mem_ptr_virt, 0, HP100_MIN_PACKET_SIZE - skb->len);
- } else { /* programmed i/o */
- outsl(ioaddr + HP100_REG_DATA32, skb->data,
- (skb->len + 3) >> 2);
- if (!ok_flag)
- for (i = (skb->len + 3) & ~3; i < HP100_MIN_PACKET_SIZE; i += 4)
- hp100_outl(0, DATA32);
- }
-
- hp100_outb(HP100_TX_CMD | HP100_SET_LB, OPTION_MSW); /* send packet */
-
- dev->stats.tx_packets++;
- dev->stats.tx_bytes += skb->len;
- hp100_ints_on();
- spin_unlock_irqrestore(&lp->lock, flags);
-
- dev_consume_skb_any(skb);
-
-#ifdef HP100_DEBUG_TX
- printk("hp100: %s: start_xmit: end\n", dev->name);
-#endif
-
- return NETDEV_TX_OK;
-
-drop:
- dev_kfree_skb(skb);
- return NETDEV_TX_OK;
-}
-
-/*
- * Receive Function (Non-Busmaster mode)
- * Called when an "Receive Packet" interrupt occurs, i.e. the receive
- * packet counter is non-zero.
- * For non-busmaster, this function does the whole work of transferring
- * the packet to the host memory and then up to higher layers via skb
- * and netif_rx.
- */
-
-static void hp100_rx(struct net_device *dev)
-{
- int packets, pkt_len;
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
- u_int header;
- struct sk_buff *skb;
-
-#ifdef DEBUG_B
- hp100_outw(0x4213, TRACE);
- printk("hp100: %s: rx\n", dev->name);
-#endif
-
- /* First get indication of received lan packet */
- /* RX_PKT_CND indicates the number of packets which have been fully */
- /* received onto the card but have not been fully transferred of the card */
- packets = hp100_inb(RX_PKT_CNT);
-#ifdef HP100_DEBUG_RX
- if (packets > 1)
- printk("hp100: %s: rx: waiting packets = %d\n", dev->name, packets);
-#endif
-
- while (packets-- > 0) {
- /* If ADV_NXT_PKT is still set, we have to wait until the card has */
- /* really advanced to the next packet. */
- for (pkt_len = 0; pkt_len < 6000 && (hp100_inb(OPTION_MSW) & HP100_ADV_NXT_PKT); pkt_len++) {
-#ifdef HP100_DEBUG_RX
- printk ("hp100: %s: rx: busy, remaining packets = %d\n", dev->name, packets);
-#endif
- }
-
- /* First we get the header, which contains information about the */
- /* actual length of the received packet. */
- if (lp->mode == 2) { /* memory mapped mode */
- header = readl(lp->mem_ptr_virt);
- } else /* programmed i/o */
- header = hp100_inl(DATA32);
-
- pkt_len = ((header & HP100_PKT_LEN_MASK) + 3) & ~3;
-
-#ifdef HP100_DEBUG_RX
- printk("hp100: %s: rx: new packet - length=%d, errors=0x%x, dest=0x%x\n",
- dev->name, header & HP100_PKT_LEN_MASK,
- (header >> 16) & 0xfff8, (header >> 16) & 7);
-#endif
-
- /* Now we allocate the skb and transfer the data into it. */
- skb = netdev_alloc_skb(dev, pkt_len + 2);
- if (skb == NULL) { /* Not enough memory->drop packet */
-#ifdef HP100_DEBUG
- printk("hp100: %s: rx: couldn't allocate a sk_buff of size %d\n",
- dev->name, pkt_len);
-#endif
- dev->stats.rx_dropped++;
- } else { /* skb successfully allocated */
-
- u_char *ptr;
-
- skb_reserve(skb, 2);
-
- /* ptr to start of the sk_buff data area */
- skb_put(skb, pkt_len);
- ptr = skb->data;
-
- /* Now transfer the data from the card into that area */
- if (lp->mode == 2)
- memcpy_fromio(ptr, lp->mem_ptr_virt, pkt_len);
- else /* io mapped */
- insl(ioaddr + HP100_REG_DATA32, ptr, pkt_len >> 2);
-
- skb->protocol = eth_type_trans(skb, dev);
-
-#ifdef HP100_DEBUG_RX
- printk("hp100: %s: rx: %02x %02x %02x %02x %02x %02x %02x %02x %02x %02x %02x %02x\n",
- dev->name, ptr[0], ptr[1], ptr[2], ptr[3],
- ptr[4], ptr[5], ptr[6], ptr[7], ptr[8],
- ptr[9], ptr[10], ptr[11]);
-#endif
- netif_rx(skb);
- dev->stats.rx_packets++;
- dev->stats.rx_bytes += pkt_len;
- }
-
- /* Indicate the card that we have got the packet */
- hp100_outb(HP100_ADV_NXT_PKT | HP100_SET_LB, OPTION_MSW);
-
- switch (header & 0x00070000) {
- case (HP100_MULTI_ADDR_HASH << 16):
- case (HP100_MULTI_ADDR_NO_HASH << 16):
- dev->stats.multicast++;
- break;
- }
- } /* end of while(there are packets) loop */
-#ifdef HP100_DEBUG_RX
- printk("hp100_rx: %s: end\n", dev->name);
-#endif
-}
-
-/*
- * Receive Function for Busmaster Mode
- */
-static void hp100_rx_bm(struct net_device *dev)
-{
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
- hp100_ring_t *ptr;
- u_int header;
- int pkt_len;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4214, TRACE);
- printk("hp100: %s: rx_bm\n", dev->name);
-#endif
-
-#ifdef HP100_DEBUG
- if (0 == lp->rxrcommit) {
- printk("hp100: %s: rx_bm called although no PDLs were committed to adapter?\n", dev->name);
- return;
- } else
- /* RX_PKT_CNT states how many PDLs are currently formatted and available to
- * the cards BM engine
- */
- if ((hp100_inw(RX_PKT_CNT) & 0x00ff) >= lp->rxrcommit) {
- printk("hp100: %s: More packets received than committed? RX_PKT_CNT=0x%x, commit=0x%x\n",
- dev->name, hp100_inw(RX_PKT_CNT) & 0x00ff,
- lp->rxrcommit);
- return;
- }
-#endif
-
- while ((lp->rxrcommit > hp100_inb(RX_PDL))) {
- /*
- * The packet was received into the pdl pointed to by lp->rxrhead (
- * the oldest pdl in the ring
- */
-
- /* First we get the header, which contains information about the */
- /* actual length of the received packet. */
-
- ptr = lp->rxrhead;
-
- header = *(ptr->pdl - 1);
- pkt_len = (header & HP100_PKT_LEN_MASK);
-
- /* Conversion to new PCI API : NOP */
- pci_unmap_single(lp->pci_dev, (dma_addr_t) ptr->pdl[3], MAX_ETHER_SIZE, PCI_DMA_FROMDEVICE);
-
-#ifdef HP100_DEBUG_BM
- printk("hp100: %s: rx_bm: header@0x%x=0x%x length=%d, errors=0x%x, dest=0x%x\n",
- dev->name, (u_int) (ptr->pdl - 1), (u_int) header,
- pkt_len, (header >> 16) & 0xfff8, (header >> 16) & 7);
- printk("hp100: %s: RX_PDL_COUNT:0x%x TX_PDL_COUNT:0x%x, RX_PKT_CNT=0x%x PDH=0x%x, Data@0x%x len=0x%x\n",
- dev->name, hp100_inb(RX_PDL), hp100_inb(TX_PDL),
- hp100_inb(RX_PKT_CNT), (u_int) * (ptr->pdl),
- (u_int) * (ptr->pdl + 3), (u_int) * (ptr->pdl + 4));
-#endif
-
- if ((pkt_len >= MIN_ETHER_SIZE) &&
- (pkt_len <= MAX_ETHER_SIZE)) {
- if (ptr->skb == NULL) {
- printk("hp100: %s: rx_bm: skb null\n", dev->name);
- /* can happen if we only allocated room for the pdh due to memory shortage. */
- dev->stats.rx_dropped++;
- } else {
- skb_trim(ptr->skb, pkt_len); /* Shorten it */
- ptr->skb->protocol =
- eth_type_trans(ptr->skb, dev);
-
- netif_rx(ptr->skb); /* Up and away... */
-
- dev->stats.rx_packets++;
- dev->stats.rx_bytes += pkt_len;
- }
-
- switch (header & 0x00070000) {
- case (HP100_MULTI_ADDR_HASH << 16):
- case (HP100_MULTI_ADDR_NO_HASH << 16):
- dev->stats.multicast++;
- break;
- }
- } else {
-#ifdef HP100_DEBUG
- printk("hp100: %s: rx_bm: Received bad packet (length=%d)\n", dev->name, pkt_len);
-#endif
- if (ptr->skb != NULL)
- dev_kfree_skb_any(ptr->skb);
- dev->stats.rx_errors++;
- }
-
- lp->rxrhead = lp->rxrhead->next;
-
- /* Allocate a new rx PDL (so lp->rxrcommit stays the same) */
- if (0 == hp100_build_rx_pdl(lp->rxrtail, dev)) {
- /* No space for skb, header can still be received. */
-#ifdef HP100_DEBUG
- printk("hp100: %s: rx_bm: No space for new PDL.\n", dev->name);
-#endif
- return;
- } else { /* successfully allocated new PDL - put it in ringlist at tail. */
- hp100_outl((u32) lp->rxrtail->pdl_paddr, RX_PDA);
- lp->rxrtail = lp->rxrtail->next;
- }
- }
-}
-
-/*
- * statistics
- */
-static struct net_device_stats *hp100_get_stats(struct net_device *dev)
-{
- unsigned long flags;
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4215, TRACE);
-#endif
-
- spin_lock_irqsave(&lp->lock, flags);
- hp100_ints_off(); /* Useful ? Jean II */
- hp100_update_stats(dev);
- hp100_ints_on();
- spin_unlock_irqrestore(&lp->lock, flags);
- return &(dev->stats);
-}
-
-static void hp100_update_stats(struct net_device *dev)
-{
- int ioaddr = dev->base_addr;
- u_short val;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4216, TRACE);
- printk("hp100: %s: update-stats\n", dev->name);
-#endif
-
- /* Note: Statistics counters clear when read. */
- hp100_page(MAC_CTRL);
- val = hp100_inw(DROPPED) & 0x0fff;
- dev->stats.rx_errors += val;
- dev->stats.rx_over_errors += val;
- val = hp100_inb(CRC);
- dev->stats.rx_errors += val;
- dev->stats.rx_crc_errors += val;
- val = hp100_inb(ABORT);
- dev->stats.tx_errors += val;
- dev->stats.tx_aborted_errors += val;
- hp100_page(PERFORMANCE);
-}
-
-static void hp100_misc_interrupt(struct net_device *dev)
-{
-#ifdef HP100_DEBUG_B
- int ioaddr = dev->base_addr;
-#endif
-
-#ifdef HP100_DEBUG_B
- int ioaddr = dev->base_addr;
- hp100_outw(0x4216, TRACE);
- printk("hp100: %s: misc_interrupt\n", dev->name);
-#endif
-
- /* Note: Statistics counters clear when read. */
- dev->stats.rx_errors++;
- dev->stats.tx_errors++;
-}
-
-static void hp100_clear_stats(struct hp100_private *lp, int ioaddr)
-{
- unsigned long flags;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4217, TRACE);
- printk("hp100: %s: clear_stats\n", dev->name);
-#endif
-
- spin_lock_irqsave(&lp->lock, flags);
- hp100_page(MAC_CTRL); /* get all statistics bytes */
- hp100_inw(DROPPED);
- hp100_inb(CRC);
- hp100_inb(ABORT);
- hp100_page(PERFORMANCE);
- spin_unlock_irqrestore(&lp->lock, flags);
-}
-
-/*
- * multicast setup
- */
-
-/*
- * Set or clear the multicast filter for this adapter.
- */
-
-static void hp100_set_multicast_list(struct net_device *dev)
-{
- unsigned long flags;
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4218, TRACE);
- printk("hp100: %s: set_mc_list\n", dev->name);
-#endif
-
- spin_lock_irqsave(&lp->lock, flags);
- hp100_ints_off();
- hp100_page(MAC_CTRL);
- hp100_andb(~(HP100_RX_EN | HP100_TX_EN), MAC_CFG_1); /* stop rx/tx */
-
- if (dev->flags & IFF_PROMISC) {
- lp->mac2_mode = HP100_MAC2MODE6; /* promiscuous mode = get all good */
- lp->mac1_mode = HP100_MAC1MODE6; /* packets on the net */
- memset(&lp->hash_bytes, 0xff, 8);
- } else if (!netdev_mc_empty(dev) || (dev->flags & IFF_ALLMULTI)) {
- lp->mac2_mode = HP100_MAC2MODE5; /* multicast mode = get packets for */
- lp->mac1_mode = HP100_MAC1MODE5; /* me, broadcasts and all multicasts */
-#ifdef HP100_MULTICAST_FILTER /* doesn't work!!! */
- if (dev->flags & IFF_ALLMULTI) {
- /* set hash filter to receive all multicast packets */
- memset(&lp->hash_bytes, 0xff, 8);
- } else {
- int i, idx;
- u_char *addrs;
- struct netdev_hw_addr *ha;
-
- memset(&lp->hash_bytes, 0x00, 8);
-#ifdef HP100_DEBUG
- printk("hp100: %s: computing hash filter - mc_count = %i\n",
- dev->name, netdev_mc_count(dev));
-#endif
- netdev_for_each_mc_addr(ha, dev) {
- addrs = ha->addr;
-#ifdef HP100_DEBUG
- printk("hp100: %s: multicast = %pM, ",
- dev->name, addrs);
-#endif
- for (i = idx = 0; i < 6; i++) {
- idx ^= *addrs++ & 0x3f;
- printk(":%02x:", idx);
- }
-#ifdef HP100_DEBUG
- printk("idx = %i\n", idx);
-#endif
- lp->hash_bytes[idx >> 3] |= (1 << (idx & 7));
- }
- }
-#else
- memset(&lp->hash_bytes, 0xff, 8);
-#endif
- } else {
- lp->mac2_mode = HP100_MAC2MODE3; /* normal mode = get packets for me */
- lp->mac1_mode = HP100_MAC1MODE3; /* and broadcasts */
- memset(&lp->hash_bytes, 0x00, 8);
- }
-
- if (((hp100_inb(MAC_CFG_1) & 0x0f) != lp->mac1_mode) ||
- (hp100_inb(MAC_CFG_2) != lp->mac2_mode)) {
- int i;
-
- hp100_outb(lp->mac2_mode, MAC_CFG_2);
- hp100_andb(HP100_MAC1MODEMASK, MAC_CFG_1); /* clear mac1 mode bits */
- hp100_orb(lp->mac1_mode, MAC_CFG_1); /* and set the new mode */
-
- hp100_page(MAC_ADDRESS);
- for (i = 0; i < 8; i++)
- hp100_outb(lp->hash_bytes[i], HASH_BYTE0 + i);
-#ifdef HP100_DEBUG
- printk("hp100: %s: mac1 = 0x%x, mac2 = 0x%x, multicast hash = %02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
- dev->name, lp->mac1_mode, lp->mac2_mode,
- lp->hash_bytes[0], lp->hash_bytes[1],
- lp->hash_bytes[2], lp->hash_bytes[3],
- lp->hash_bytes[4], lp->hash_bytes[5],
- lp->hash_bytes[6], lp->hash_bytes[7]);
-#endif
-
- if (lp->lan_type == HP100_LAN_100) {
-#ifdef HP100_DEBUG
- printk("hp100: %s: 100VG MAC settings have changed - relogin.\n", dev->name);
-#endif
- lp->hub_status = hp100_login_to_vg_hub(dev, 1); /* force a relogin to the hub */
- }
- } else {
- int i;
- u_char old_hash_bytes[8];
-
- hp100_page(MAC_ADDRESS);
- for (i = 0; i < 8; i++)
- old_hash_bytes[i] = hp100_inb(HASH_BYTE0 + i);
- if (memcmp(old_hash_bytes, &lp->hash_bytes, 8)) {
- for (i = 0; i < 8; i++)
- hp100_outb(lp->hash_bytes[i], HASH_BYTE0 + i);
-#ifdef HP100_DEBUG
- printk("hp100: %s: multicast hash = %02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
- dev->name, lp->hash_bytes[0],
- lp->hash_bytes[1], lp->hash_bytes[2],
- lp->hash_bytes[3], lp->hash_bytes[4],
- lp->hash_bytes[5], lp->hash_bytes[6],
- lp->hash_bytes[7]);
-#endif
-
- if (lp->lan_type == HP100_LAN_100) {
-#ifdef HP100_DEBUG
- printk("hp100: %s: 100VG MAC settings have changed - relogin.\n", dev->name);
-#endif
- lp->hub_status = hp100_login_to_vg_hub(dev, 1); /* force a relogin to the hub */
- }
- }
- }
-
- hp100_page(MAC_CTRL);
- hp100_orb(HP100_RX_EN | HP100_RX_IDLE | /* enable rx */
- HP100_TX_EN | HP100_TX_IDLE, MAC_CFG_1); /* enable tx */
-
- hp100_page(PERFORMANCE);
- hp100_ints_on();
- spin_unlock_irqrestore(&lp->lock, flags);
-}
-
-/*
- * hardware interrupt handling
- */
-
-static irqreturn_t hp100_interrupt(int irq, void *dev_id)
-{
- struct net_device *dev = (struct net_device *) dev_id;
- struct hp100_private *lp = netdev_priv(dev);
-
- int ioaddr;
- u_int val;
-
- if (dev == NULL)
- return IRQ_NONE;
- ioaddr = dev->base_addr;
-
- spin_lock(&lp->lock);
-
- hp100_ints_off();
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4219, TRACE);
-#endif
-
- /* hp100_page( PERFORMANCE ); */
- val = hp100_inw(IRQ_STATUS);
-#ifdef HP100_DEBUG_IRQ
- printk("hp100: %s: mode=%x,IRQ_STAT=0x%.4x,RXPKTCNT=0x%.2x RXPDL=0x%.2x TXPKTCNT=0x%.2x TXPDL=0x%.2x\n",
- dev->name, lp->mode, (u_int) val, hp100_inb(RX_PKT_CNT),
- hp100_inb(RX_PDL), hp100_inb(TX_PKT_CNT), hp100_inb(TX_PDL));
-#endif
-
- if (val == 0) { /* might be a shared interrupt */
- spin_unlock(&lp->lock);
- hp100_ints_on();
- return IRQ_NONE;
- }
- /* We're only interested in those interrupts we really enabled. */
- /* val &= hp100_inw( IRQ_MASK ); */
-
- /*
- * RX_PDL_FILL_COMPL is set whenever a RX_PDL has been executed. A RX_PDL
- * is considered executed whenever the RX_PDL data structure is no longer
- * needed.
- */
- if (val & HP100_RX_PDL_FILL_COMPL) {
- if (lp->mode == 1)
- hp100_rx_bm(dev);
- else {
- printk("hp100: %s: rx_pdl_fill_compl interrupt although not busmaster?\n", dev->name);
- }
- }
-
- /*
- * The RX_PACKET interrupt is set, when the receive packet counter is
- * non zero. We use this interrupt for receiving in slave mode. In
- * busmaster mode, we use it to make sure we did not miss any rx_pdl_fill
- * interrupts. If rx_pdl_fill_compl is not set and rx_packet is set, then
- * we somehow have missed a rx_pdl_fill_compl interrupt.
- */
-
- if (val & HP100_RX_PACKET) { /* Receive Packet Counter is non zero */
- if (lp->mode != 1) /* non busmaster */
- hp100_rx(dev);
- else if (!(val & HP100_RX_PDL_FILL_COMPL)) {
- /* Shouldn't happen - maybe we missed a RX_PDL_FILL Interrupt? */
- hp100_rx_bm(dev);
- }
- }
-
- /*
- * Ack. that we have noticed the interrupt and thereby allow next one.
- * Note that this is now done after the slave rx function, since first
- * acknowledging and then setting ADV_NXT_PKT caused an extra interrupt
- * on the J2573.
- */
- hp100_outw(val, IRQ_STATUS);
-
- /*
- * RX_ERROR is set when a packet is dropped due to no memory resources on
- * the card or when a RCV_ERR occurs.
- * TX_ERROR is set when a TX_ABORT condition occurs in the MAC->exists
- * only in the 802.3 MAC and happens when 16 collisions occur during a TX
- */
- if (val & (HP100_TX_ERROR | HP100_RX_ERROR)) {
-#ifdef HP100_DEBUG_IRQ
- printk("hp100: %s: TX/RX Error IRQ\n", dev->name);
-#endif
- hp100_update_stats(dev);
- if (lp->mode == 1) {
- hp100_rxfill(dev);
- hp100_clean_txring(dev);
- }
- }
-
- /*
- * RX_PDA_ZERO is set when the PDA count goes from non-zero to zero.
- */
- if ((lp->mode == 1) && (val & (HP100_RX_PDA_ZERO)))
- hp100_rxfill(dev);
-
- /*
- * HP100_TX_COMPLETE interrupt occurs when packet transmitted on wire
- * is completed
- */
- if ((lp->mode == 1) && (val & (HP100_TX_COMPLETE)))
- hp100_clean_txring(dev);
-
- /*
- * MISC_ERROR is set when either the LAN link goes down or a detected
- * bus error occurs.
- */
- if (val & HP100_MISC_ERROR) { /* New for J2585B */
-#ifdef HP100_DEBUG_IRQ
- printk
- ("hp100: %s: Misc. Error Interrupt - Check cabling.\n",
- dev->name);
-#endif
- if (lp->mode == 1) {
- hp100_clean_txring(dev);
- hp100_rxfill(dev);
- }
- hp100_misc_interrupt(dev);
- }
-
- spin_unlock(&lp->lock);
- hp100_ints_on();
- return IRQ_HANDLED;
-}
-
-/*
- * some misc functions
- */
-
-static void hp100_start_interface(struct net_device *dev)
-{
- unsigned long flags;
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4220, TRACE);
- printk("hp100: %s: hp100_start_interface\n", dev->name);
-#endif
-
- spin_lock_irqsave(&lp->lock, flags);
-
- /* Ensure the adapter does not want to request an interrupt when */
- /* enabling the IRQ line to be active on the bus (i.e. not tri-stated) */
- hp100_page(PERFORMANCE);
- hp100_outw(0xfefe, IRQ_MASK); /* mask off all ints */
- hp100_outw(0xffff, IRQ_STATUS); /* ack all IRQs */
- hp100_outw(HP100_FAKE_INT | HP100_INT_EN | HP100_RESET_LB,
- OPTION_LSW);
- /* Un Tri-state int. TODO: Check if shared interrupts can be realised? */
- hp100_outw(HP100_TRI_INT | HP100_RESET_HB, OPTION_LSW);
-
- if (lp->mode == 1) {
- /* Make sure BM bit is set... */
- hp100_page(HW_MAP);
- hp100_orb(HP100_BM_MASTER, BM);
- hp100_rxfill(dev);
- } else if (lp->mode == 2) {
- /* Enable memory mapping. Note: Don't do this when busmaster. */
- hp100_outw(HP100_MMAP_DIS | HP100_RESET_HB, OPTION_LSW);
- }
-
- hp100_page(PERFORMANCE);
- hp100_outw(0xfefe, IRQ_MASK); /* mask off all ints */
- hp100_outw(0xffff, IRQ_STATUS); /* ack IRQ */
-
- /* enable a few interrupts: */
- if (lp->mode == 1) { /* busmaster mode */
- hp100_outw(HP100_RX_PDL_FILL_COMPL |
- HP100_RX_PDA_ZERO | HP100_RX_ERROR |
- /* HP100_RX_PACKET | */
- /* HP100_RX_EARLY_INT | */ HP100_SET_HB |
- /* HP100_TX_PDA_ZERO | */
- HP100_TX_COMPLETE |
- /* HP100_MISC_ERROR | */
- HP100_TX_ERROR | HP100_SET_LB, IRQ_MASK);
- } else {
- hp100_outw(HP100_RX_PACKET |
- HP100_RX_ERROR | HP100_SET_HB |
- HP100_TX_ERROR | HP100_SET_LB, IRQ_MASK);
- }
-
- /* Note : before hp100_set_multicast_list(), because it will play with
- * spinlock itself... Jean II
- */
- spin_unlock_irqrestore(&lp->lock, flags);
-
- /* Enable MAC Tx and RX, set MAC modes, ... */
- hp100_set_multicast_list(dev);
-}
-
-static void hp100_stop_interface(struct net_device *dev)
-{
- struct hp100_private *lp = netdev_priv(dev);
- int ioaddr = dev->base_addr;
- u_int val;
-
-#ifdef HP100_DEBUG_B
- printk("hp100: %s: hp100_stop_interface\n", dev->name);
- hp100_outw(0x4221, TRACE);
-#endif
-
- if (lp->mode == 1)
- hp100_BM_shutdown(dev);
- else {
- /* Note: MMAP_DIS will be reenabled by start_interface */
- hp100_outw(HP100_INT_EN | HP100_RESET_LB |
- HP100_TRI_INT | HP100_MMAP_DIS | HP100_SET_HB,
- OPTION_LSW);
- val = hp100_inw(OPTION_LSW);
-
- hp100_page(MAC_CTRL);
- hp100_andb(~(HP100_RX_EN | HP100_TX_EN), MAC_CFG_1);
-
- if (!(val & HP100_HW_RST))
- return; /* If reset, imm. return ... */
- /* ... else: busy wait until idle */
- for (val = 0; val < 6000; val++)
- if ((hp100_inb(MAC_CFG_1) & (HP100_TX_IDLE | HP100_RX_IDLE)) == (HP100_TX_IDLE | HP100_RX_IDLE)) {
- hp100_page(PERFORMANCE);
- return;
- }
- printk("hp100: %s: hp100_stop_interface - timeout\n", dev->name);
- hp100_page(PERFORMANCE);
- }
-}
-
-static void hp100_load_eeprom(struct net_device *dev, u_short probe_ioaddr)
-{
- int i;
- int ioaddr = probe_ioaddr > 0 ? probe_ioaddr : dev->base_addr;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4222, TRACE);
-#endif
-
- hp100_page(EEPROM_CTRL);
- hp100_andw(~HP100_EEPROM_LOAD, EEPROM_CTRL);
- hp100_orw(HP100_EEPROM_LOAD, EEPROM_CTRL);
- for (i = 0; i < 10000; i++)
- if (!(hp100_inb(OPTION_MSW) & HP100_EE_LOAD))
- return;
- printk("hp100: %s: hp100_load_eeprom - timeout\n", dev->name);
-}
-
-/* Sense connection status.
- * return values: LAN_10 - Connected to 10Mbit/s network
- * LAN_100 - Connected to 100Mbit/s network
- * LAN_ERR - not connected or 100Mbit/s Hub down
- */
-static int hp100_sense_lan(struct net_device *dev)
-{
- int ioaddr = dev->base_addr;
- u_short val_VG, val_10;
- struct hp100_private *lp = netdev_priv(dev);
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4223, TRACE);
-#endif
-
- hp100_page(MAC_CTRL);
- val_10 = hp100_inb(10_LAN_CFG_1);
- val_VG = hp100_inb(VG_LAN_CFG_1);
- hp100_page(PERFORMANCE);
-#ifdef HP100_DEBUG
- printk("hp100: %s: sense_lan: val_VG = 0x%04x, val_10 = 0x%04x\n",
- dev->name, val_VG, val_10);
-#endif
-
- if (val_10 & HP100_LINK_BEAT_ST) /* 10Mb connection is active */
- return HP100_LAN_10;
-
- if (val_10 & HP100_AUI_ST) { /* have we BNC or AUI onboard? */
- /*
- * This can be overridden by dos utility, so if this has no effect,
- * perhaps you need to download that utility from HP and set card
- * back to "auto detect".
- */
- val_10 |= HP100_AUI_SEL | HP100_LOW_TH;
- hp100_page(MAC_CTRL);
- hp100_outb(val_10, 10_LAN_CFG_1);
- hp100_page(PERFORMANCE);
- return HP100_LAN_COAX;
- }
-
- /* Those cards don't have a 100 Mbit connector */
- if (!strcmp(lp->id, "HWP1920") ||
- (lp->pci_dev &&
- lp->pci_dev->vendor == PCI_VENDOR_ID &&
- (lp->pci_dev->device == PCI_DEVICE_ID_HP_J2970A ||
- lp->pci_dev->device == PCI_DEVICE_ID_HP_J2973A)))
- return HP100_LAN_ERR;
-
- if (val_VG & HP100_LINK_CABLE_ST) /* Can hear the HUBs tone. */
- return HP100_LAN_100;
- return HP100_LAN_ERR;
-}
-
-static int hp100_down_vg_link(struct net_device *dev)
-{
- struct hp100_private *lp = netdev_priv(dev);
- int ioaddr = dev->base_addr;
- unsigned long time;
- long savelan, newlan;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4224, TRACE);
- printk("hp100: %s: down_vg_link\n", dev->name);
-#endif
-
- hp100_page(MAC_CTRL);
- time = jiffies + (HZ / 4);
- do {
- if (hp100_inb(VG_LAN_CFG_1) & HP100_LINK_CABLE_ST)
- break;
- if (!in_interrupt())
- schedule_timeout_interruptible(1);
- } while (time_after(time, jiffies));
-
- if (time_after_eq(jiffies, time)) /* no signal->no logout */
- return 0;
-
- /* Drop the VG Link by clearing the link up cmd and load addr. */
-
- hp100_andb(~(HP100_LOAD_ADDR | HP100_LINK_CMD), VG_LAN_CFG_1);
- hp100_orb(HP100_VG_SEL, VG_LAN_CFG_1);
-
- /* Conditionally stall for >250ms on Link-Up Status (to go down) */
- time = jiffies + (HZ / 2);
- do {
- if (!(hp100_inb(VG_LAN_CFG_1) & HP100_LINK_UP_ST))
- break;
- if (!in_interrupt())
- schedule_timeout_interruptible(1);
- } while (time_after(time, jiffies));
-
-#ifdef HP100_DEBUG
- if (time_after_eq(jiffies, time))
- printk("hp100: %s: down_vg_link: Link does not go down?\n", dev->name);
-#endif
-
- /* To prevent condition where Rev 1 VG MAC and old hubs do not complete */
- /* logout under traffic (even though all the status bits are cleared), */
- /* do this workaround to get the Rev 1 MAC in its idle state */
- if (lp->chip == HP100_CHIPID_LASSEN) {
- /* Reset VG MAC to insure it leaves the logoff state even if */
- /* the Hub is still emitting tones */
- hp100_andb(~HP100_VG_RESET, VG_LAN_CFG_1);
- udelay(1500); /* wait for >1ms */
- hp100_orb(HP100_VG_RESET, VG_LAN_CFG_1); /* Release Reset */
- udelay(1500);
- }
-
- /* New: For lassen, switch to 10 Mbps mac briefly to clear training ACK */
- /* to get the VG mac to full reset. This is not req.d with later chips */
- /* Note: It will take the between 1 and 2 seconds for the VG mac to be */
- /* selected again! This will be left to the connect hub function to */
- /* perform if desired. */
- if (lp->chip == HP100_CHIPID_LASSEN) {
- /* Have to write to 10 and 100VG control registers simultaneously */
- savelan = newlan = hp100_inl(10_LAN_CFG_1); /* read 10+100 LAN_CFG regs */
- newlan &= ~(HP100_VG_SEL << 16);
- newlan |= (HP100_DOT3_MAC) << 8;
- hp100_andb(~HP100_AUTO_MODE, MAC_CFG_3); /* Autosel off */
- hp100_outl(newlan, 10_LAN_CFG_1);
-
- /* Conditionally stall for 5sec on VG selected. */
- time = jiffies + (HZ * 5);
- do {
- if (!(hp100_inb(MAC_CFG_4) & HP100_MAC_SEL_ST))
- break;
- if (!in_interrupt())
- schedule_timeout_interruptible(1);
- } while (time_after(time, jiffies));
-
- hp100_orb(HP100_AUTO_MODE, MAC_CFG_3); /* Autosel back on */
- hp100_outl(savelan, 10_LAN_CFG_1);
- }
-
- time = jiffies + (3 * HZ); /* Timeout 3s */
- do {
- if ((hp100_inb(VG_LAN_CFG_1) & HP100_LINK_CABLE_ST) == 0)
- break;
- if (!in_interrupt())
- schedule_timeout_interruptible(1);
- } while (time_after(time, jiffies));
-
- if (time_before_eq(time, jiffies)) {
-#ifdef HP100_DEBUG
- printk("hp100: %s: down_vg_link: timeout\n", dev->name);
-#endif
- return -EIO;
- }
-
- time = jiffies + (2 * HZ); /* This seems to take a while.... */
- do {
- if (!in_interrupt())
- schedule_timeout_interruptible(1);
- } while (time_after(time, jiffies));
-
- return 0;
-}
-
-static int hp100_login_to_vg_hub(struct net_device *dev, u_short force_relogin)
-{
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
- u_short val = 0;
- unsigned long time;
- int startst;
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4225, TRACE);
- printk("hp100: %s: login_to_vg_hub\n", dev->name);
-#endif
-
- /* Initiate a login sequence iff VG MAC is enabled and either Load Address
- * bit is zero or the force relogin flag is set (e.g. due to MAC address or
- * promiscuous mode change)
- */
- hp100_page(MAC_CTRL);
- startst = hp100_inb(VG_LAN_CFG_1);
- if ((force_relogin == 1) || (hp100_inb(MAC_CFG_4) & HP100_MAC_SEL_ST)) {
-#ifdef HP100_DEBUG_TRAINING
- printk("hp100: %s: Start training\n", dev->name);
-#endif
-
- /* Ensure VG Reset bit is 1 (i.e., do not reset) */
- hp100_orb(HP100_VG_RESET, VG_LAN_CFG_1);
-
- /* If Lassen AND auto-select-mode AND VG tones were sensed on */
- /* entry then temporarily put them into force 100Mbit mode */
- if ((lp->chip == HP100_CHIPID_LASSEN) && (startst & HP100_LINK_CABLE_ST))
- hp100_andb(~HP100_DOT3_MAC, 10_LAN_CFG_2);
-
- /* Drop the VG link by zeroing Link Up Command and Load Address */
- hp100_andb(~(HP100_LINK_CMD /* |HP100_LOAD_ADDR */ ), VG_LAN_CFG_1);
-
-#ifdef HP100_DEBUG_TRAINING
- printk("hp100: %s: Bring down the link\n", dev->name);
-#endif
-
- /* Wait for link to drop */
- time = jiffies + (HZ / 10);
- do {
- if (!(hp100_inb(VG_LAN_CFG_1) & HP100_LINK_UP_ST))
- break;
- if (!in_interrupt())
- schedule_timeout_interruptible(1);
- } while (time_after(time, jiffies));
-
- /* Start an addressed training and optionally request promiscuous port */
- if ((dev->flags) & IFF_PROMISC) {
- hp100_orb(HP100_PROM_MODE, VG_LAN_CFG_2);
- if (lp->chip == HP100_CHIPID_LASSEN)
- hp100_orw(HP100_MACRQ_PROMSC, TRAIN_REQUEST);
- } else {
- hp100_andb(~HP100_PROM_MODE, VG_LAN_CFG_2);
- /* For ETR parts we need to reset the prom. bit in the training
- * register, otherwise promiscious mode won't be disabled.
- */
- if (lp->chip == HP100_CHIPID_LASSEN) {
- hp100_andw(~HP100_MACRQ_PROMSC, TRAIN_REQUEST);
- }
- }
-
- /* With ETR parts, frame format request bits can be set. */
- if (lp->chip == HP100_CHIPID_LASSEN)
- hp100_orb(HP100_MACRQ_FRAMEFMT_EITHER, TRAIN_REQUEST);
-
- hp100_orb(HP100_LINK_CMD | HP100_LOAD_ADDR | HP100_VG_RESET, VG_LAN_CFG_1);
-
- /* Note: Next wait could be omitted for Hood and earlier chips under */
- /* certain circumstances */
- /* TODO: check if hood/earlier and skip wait. */
-
- /* Wait for either short timeout for VG tones or long for login */
- /* Wait for the card hardware to signalise link cable status ok... */
- hp100_page(MAC_CTRL);
- time = jiffies + (1 * HZ); /* 1 sec timeout for cable st */
- do {
- if (hp100_inb(VG_LAN_CFG_1) & HP100_LINK_CABLE_ST)
- break;
- if (!in_interrupt())
- schedule_timeout_interruptible(1);
- } while (time_before(jiffies, time));
-
- if (time_after_eq(jiffies, time)) {
-#ifdef HP100_DEBUG_TRAINING
- printk("hp100: %s: Link cable status not ok? Training aborted.\n", dev->name);
-#endif
- } else {
-#ifdef HP100_DEBUG_TRAINING
- printk
- ("hp100: %s: HUB tones detected. Trying to train.\n",
- dev->name);
-#endif
-
- time = jiffies + (2 * HZ); /* again a timeout */
- do {
- val = hp100_inb(VG_LAN_CFG_1);
- if ((val & (HP100_LINK_UP_ST))) {
-#ifdef HP100_DEBUG_TRAINING
- printk("hp100: %s: Passed training.\n", dev->name);
-#endif
- break;
- }
- if (!in_interrupt())
- schedule_timeout_interruptible(1);
- } while (time_after(time, jiffies));
- }
-
- /* If LINK_UP_ST is set, then we are logged into the hub. */
- if (time_before_eq(jiffies, time) && (val & HP100_LINK_UP_ST)) {
-#ifdef HP100_DEBUG_TRAINING
- printk("hp100: %s: Successfully logged into the HUB.\n", dev->name);
- if (lp->chip == HP100_CHIPID_LASSEN) {
- val = hp100_inw(TRAIN_ALLOW);
- printk("hp100: %s: Card supports 100VG MAC Version \"%s\" ",
- dev->name, (hp100_inw(TRAIN_REQUEST) & HP100_CARD_MACVER) ? "802.12" : "Pre");
- printk("Driver will use MAC Version \"%s\"\n", (val & HP100_HUB_MACVER) ? "802.12" : "Pre");
- printk("hp100: %s: Frame format is %s.\n", dev->name, (val & HP100_MALLOW_FRAMEFMT) ? "802.5" : "802.3");
- }
-#endif
- } else {
- /* If LINK_UP_ST is not set, login was not successful */
- printk("hp100: %s: Problem logging into the HUB.\n", dev->name);
- if (lp->chip == HP100_CHIPID_LASSEN) {
- /* Check allowed Register to find out why there is a problem. */
- val = hp100_inw(TRAIN_ALLOW); /* won't work on non-ETR card */
-#ifdef HP100_DEBUG_TRAINING
- printk("hp100: %s: MAC Configuration requested: 0x%04x, HUB allowed: 0x%04x\n", dev->name, hp100_inw(TRAIN_REQUEST), val);
-#endif
- if (val & HP100_MALLOW_ACCDENIED)
- printk("hp100: %s: HUB access denied.\n", dev->name);
- if (val & HP100_MALLOW_CONFIGURE)
- printk("hp100: %s: MAC Configuration is incompatible with the Network.\n", dev->name);
- if (val & HP100_MALLOW_DUPADDR)
- printk("hp100: %s: Duplicate MAC Address on the Network.\n", dev->name);
- }
- }
-
- /* If we have put the chip into forced 100 Mbit mode earlier, go back */
- /* to auto-select mode */
-
- if ((lp->chip == HP100_CHIPID_LASSEN) && (startst & HP100_LINK_CABLE_ST)) {
- hp100_page(MAC_CTRL);
- hp100_orb(HP100_DOT3_MAC, 10_LAN_CFG_2);
- }
-
- val = hp100_inb(VG_LAN_CFG_1);
-
- /* Clear the MISC_ERROR Interrupt, which might be generated when doing the relogin */
- hp100_page(PERFORMANCE);
- hp100_outw(HP100_MISC_ERROR, IRQ_STATUS);
-
- if (val & HP100_LINK_UP_ST)
- return 0; /* login was ok */
- else {
- printk("hp100: %s: Training failed.\n", dev->name);
- hp100_down_vg_link(dev);
- return -EIO;
- }
- }
- /* no forced relogin & already link there->no training. */
- return -EIO;
-}
-
-static void hp100_cascade_reset(struct net_device *dev, u_short enable)
-{
- int ioaddr = dev->base_addr;
- struct hp100_private *lp = netdev_priv(dev);
-
-#ifdef HP100_DEBUG_B
- hp100_outw(0x4226, TRACE);
- printk("hp100: %s: cascade_reset\n", dev->name);
-#endif
-
- if (enable) {
- hp100_outw(HP100_HW_RST | HP100_RESET_LB, OPTION_LSW);
- if (lp->chip == HP100_CHIPID_LASSEN) {
- /* Lassen requires a PCI transmit fifo reset */
- hp100_page(HW_MAP);
- hp100_andb(~HP100_PCI_RESET, PCICTRL2);
- hp100_orb(HP100_PCI_RESET, PCICTRL2);
- /* Wait for min. 300 ns */
- /* we can't use jiffies here, because it may be */
- /* that we have disabled the timer... */
- udelay(400);
- hp100_andb(~HP100_PCI_RESET, PCICTRL2);
- hp100_page(PERFORMANCE);
- }
- } else { /* bring out of reset */
- hp100_outw(HP100_HW_RST | HP100_SET_LB, OPTION_LSW);
- udelay(400);
- hp100_page(PERFORMANCE);
- }
-}
-
-#ifdef HP100_DEBUG
-void hp100_RegisterDump(struct net_device *dev)
-{
- int ioaddr = dev->base_addr;
- int Page;
- int Register;
-
- /* Dump common registers */
- printk("hp100: %s: Cascade Register Dump\n", dev->name);
- printk("hardware id #1: 0x%.2x\n", hp100_inb(HW_ID));
- printk("hardware id #2/paging: 0x%.2x\n", hp100_inb(PAGING));
- printk("option #1: 0x%.4x\n", hp100_inw(OPTION_LSW));
- printk("option #2: 0x%.4x\n", hp100_inw(OPTION_MSW));
-
- /* Dump paged registers */
- for (Page = 0; Page < 8; Page++) {
- /* Dump registers */
- printk("page: 0x%.2x\n", Page);
- outw(Page, ioaddr + 0x02);
- for (Register = 0x8; Register < 0x22; Register += 2) {
- /* Display Register contents except data port */
- if (((Register != 0x10) && (Register != 0x12)) || (Page > 0)) {
- printk("0x%.2x = 0x%.4x\n", Register, inw(ioaddr + Register));
- }
- }
- }
- hp100_page(PERFORMANCE);
-}
-#endif
-
-static void cleanup_dev(struct net_device *d)
-{
- struct hp100_private *p = netdev_priv(d);
-
- unregister_netdev(d);
- release_region(d->base_addr, HP100_REGION_SIZE);
-
- if (p->mode == 1) /* busmaster */
- pci_free_consistent(p->pci_dev, MAX_RINGSIZE + 0x0f,
- p->page_vaddr_algn,
- virt_to_whatever(d, p->page_vaddr_algn));
- if (p->mem_ptr_virt)
- iounmap(p->mem_ptr_virt);
-
- free_netdev(d);
-}
-
-static int hp100_eisa_probe(struct device *gendev)
-{
- struct net_device *dev = alloc_etherdev(sizeof(struct hp100_private));
- struct eisa_device *edev = to_eisa_device(gendev);
- int err;
-
- if (!dev)
- return -ENOMEM;
-
- SET_NETDEV_DEV(dev, &edev->dev);
-
- err = hp100_probe1(dev, edev->base_addr + 0xC38, HP100_BUS_EISA, NULL);
- if (err)
- goto out1;
-
-#ifdef HP100_DEBUG
- printk("hp100: %s: EISA adapter found at 0x%x\n", dev->name,
- dev->base_addr);
-#endif
- dev_set_drvdata(gendev, dev);
- return 0;
- out1:
- free_netdev(dev);
- return err;
-}
-
-static int hp100_eisa_remove(struct device *gendev)
-{
- struct net_device *dev = dev_get_drvdata(gendev);
- cleanup_dev(dev);
- return 0;
-}
-
-static struct eisa_driver hp100_eisa_driver = {
- .id_table = hp100_eisa_tbl,
- .driver = {
- .name = "hp100",
- .probe = hp100_eisa_probe,
- .remove = hp100_eisa_remove,
- }
-};
-
-static int hp100_pci_probe(struct pci_dev *pdev,
- const struct pci_device_id *ent)
-{
- struct net_device *dev;
- int ioaddr;
- u_short pci_command;
- int err;
-
- if (pci_enable_device(pdev))
- return -ENODEV;
-
- dev = alloc_etherdev(sizeof(struct hp100_private));
- if (!dev) {
- err = -ENOMEM;
- goto out0;
- }
-
- SET_NETDEV_DEV(dev, &pdev->dev);
-
- pci_read_config_word(pdev, PCI_COMMAND, &pci_command);
- if (!(pci_command & PCI_COMMAND_IO)) {
-#ifdef HP100_DEBUG
- printk("hp100: %s: PCI I/O Bit has not been set. Setting...\n", dev->name);
-#endif
- pci_command |= PCI_COMMAND_IO;
- pci_write_config_word(pdev, PCI_COMMAND, pci_command);
- }
-
- if (!(pci_command & PCI_COMMAND_MASTER)) {
-#ifdef HP100_DEBUG
- printk("hp100: %s: PCI Master Bit has not been set. Setting...\n", dev->name);
-#endif
- pci_command |= PCI_COMMAND_MASTER;
- pci_write_config_word(pdev, PCI_COMMAND, pci_command);
- }
-
- ioaddr = pci_resource_start(pdev, 0);
- err = hp100_probe1(dev, ioaddr, HP100_BUS_PCI, pdev);
- if (err)
- goto out1;
-
-#ifdef HP100_DEBUG
- printk("hp100: %s: PCI adapter found at 0x%x\n", dev->name, ioaddr);
-#endif
- pci_set_drvdata(pdev, dev);
- return 0;
- out1:
- free_netdev(dev);
- out0:
- pci_disable_device(pdev);
- return err;
-}
-
-static void hp100_pci_remove(struct pci_dev *pdev)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
-
- cleanup_dev(dev);
- pci_disable_device(pdev);
-}
-
-static struct pci_driver hp100_pci_driver = {
- .name = "hp100",
- .id_table = hp100_pci_tbl,
- .probe = hp100_pci_probe,
- .remove = hp100_pci_remove,
-};
-
-/*
- * module section
- */
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Jaroslav Kysela <perex@perex.cz>, "
- "Siegfried \"Frieder\" Loeffler (dg1sek) <floeff@mathematik.uni-stuttgart.de>");
-MODULE_DESCRIPTION("HP CASCADE Architecture Driver for 100VG-AnyLan Network Adapters");
-
-/*
- * Note: to register three isa devices, use:
- * option hp100 hp100_port=0,0,0
- * to register one card at io 0x280 as eth239, use:
- * option hp100 hp100_port=0x280
- */
-#if defined(MODULE) && defined(CONFIG_ISA)
-#define HP100_DEVICES 5
-/* Parameters set by insmod */
-static int hp100_port[HP100_DEVICES] = { 0, [1 ... (HP100_DEVICES - 1)] = -1 };
-module_param_hw_array(hp100_port, int, ioport, NULL, 0);
-
-/* List of devices */
-static struct net_device *hp100_devlist[HP100_DEVICES];
-
-static int __init hp100_isa_init(void)
-{
- struct net_device *dev;
- int i, err, cards = 0;
-
- /* Don't autoprobe ISA bus */
- if (hp100_port[0] == 0)
- return -ENODEV;
-
- /* Loop on all possible base addresses */
- for (i = 0; i < HP100_DEVICES && hp100_port[i] != -1; ++i) {
- dev = alloc_etherdev(sizeof(struct hp100_private));
- if (!dev) {
- while (cards > 0)
- cleanup_dev(hp100_devlist[--cards]);
-
- return -ENOMEM;
- }
-
- err = hp100_isa_probe(dev, hp100_port[i]);
- if (!err)
- hp100_devlist[cards++] = dev;
- else
- free_netdev(dev);
- }
-
- return cards > 0 ? 0 : -ENODEV;
-}
-
-static void hp100_isa_cleanup(void)
-{
- int i;
-
- for (i = 0; i < HP100_DEVICES; i++) {
- struct net_device *dev = hp100_devlist[i];
- if (dev)
- cleanup_dev(dev);
- }
-}
-#else
-#define hp100_isa_init() (0)
-#define hp100_isa_cleanup() do { } while (0)
-#endif
-
-static int __init hp100_module_init(void)
-{
- int err;
-
- err = hp100_isa_init();
- if (err && err != -ENODEV)
- goto out;
- err = eisa_driver_register(&hp100_eisa_driver);
- if (err && err != -ENODEV)
- goto out2;
- err = pci_register_driver(&hp100_pci_driver);
- if (err && err != -ENODEV)
- goto out3;
- out:
- return err;
- out3:
- eisa_driver_unregister (&hp100_eisa_driver);
- out2:
- hp100_isa_cleanup();
- goto out;
-}
-
-static void __exit hp100_module_exit(void)
-{
- hp100_isa_cleanup();
- eisa_driver_unregister (&hp100_eisa_driver);
- pci_unregister_driver (&hp100_pci_driver);
-}
-
-module_init(hp100_module_init)
-module_exit(hp100_module_exit)
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * hp100.h: Hewlett Packard HP10/100VG ANY LAN ethernet driver for Linux.
- *
- * $Id: hp100.h,v 1.51 1997/04/08 14:26:42 floeff Exp floeff $
- *
- * Authors: Jaroslav Kysela, <perex@pf.jcu.cz>
- * Siegfried Loeffler <floeff@tunix.mathematik.uni-stuttgart.de>
- *
- * This driver is based on the 'hpfepkt' crynwr packet driver.
- */
-
-/****************************************************************************
- * Hardware Constants
- ****************************************************************************/
-
-/*
- * Page Identifiers
- * (Swap Paging Register, PAGING, bits 3:0, Offset 0x02)
- */
-
-#define HP100_PAGE_PERFORMANCE 0x0 /* Page 0 */
-#define HP100_PAGE_MAC_ADDRESS 0x1 /* Page 1 */
-#define HP100_PAGE_HW_MAP 0x2 /* Page 2 */
-#define HP100_PAGE_EEPROM_CTRL 0x3 /* Page 3 */
-#define HP100_PAGE_MAC_CTRL 0x4 /* Page 4 */
-#define HP100_PAGE_MMU_CFG 0x5 /* Page 5 */
-#define HP100_PAGE_ID_MAC_ADDR 0x6 /* Page 6 */
-#define HP100_PAGE_MMU_POINTER 0x7 /* Page 7 */
-
-
-/* Registers that are present on all pages */
-
-#define HP100_REG_HW_ID 0x00 /* R: (16) Unique card ID */
-#define HP100_REG_TRACE 0x00 /* W: (16) Used for debug output */
-#define HP100_REG_PAGING 0x02 /* R: (16),15:4 Card ID */
- /* W: (16),3:0 Switch pages */
-#define HP100_REG_OPTION_LSW 0x04 /* RW: (16) Select card functions */
-#define HP100_REG_OPTION_MSW 0x06 /* RW: (16) Select card functions */
-
-/* Page 0 - Performance */
-
-#define HP100_REG_IRQ_STATUS 0x08 /* RW: (16) Which ints are pending */
-#define HP100_REG_IRQ_MASK 0x0a /* RW: (16) Select ints to allow */
-#define HP100_REG_FRAGMENT_LEN 0x0c /* W: (16)12:0 Current fragment len */
-/* Note: For 32 bit systems, fragment len and offset registers are available */
-/* at offset 0x28 and 0x2c, where they can be written as 32bit values. */
-#define HP100_REG_OFFSET 0x0e /* RW: (16)12:0 Offset to start read */
-#define HP100_REG_DATA32 0x10 /* RW: (32) I/O mode data port */
-#define HP100_REG_DATA16 0x12 /* RW: WORDs must be read from here */
-#define HP100_REG_TX_MEM_FREE 0x14 /* RD: (32) Amount of free Tx mem */
-#define HP100_REG_TX_PDA_L 0x14 /* W: (32) BM: Ptr to PDL, Low Pri */
-#define HP100_REG_TX_PDA_H 0x1c /* W: (32) BM: Ptr to PDL, High Pri */
-#define HP100_REG_RX_PKT_CNT 0x18 /* RD: (8) Rx count of pkts on card */
-#define HP100_REG_TX_PKT_CNT 0x19 /* RD: (8) Tx count of pkts on card */
-#define HP100_REG_RX_PDL 0x1a /* R: (8) BM: # rx pdl not executed */
-#define HP100_REG_TX_PDL 0x1b /* R: (8) BM: # tx pdl not executed */
-#define HP100_REG_RX_PDA 0x18 /* W: (32) BM: Up to 31 addresses */
- /* which point to a PDL */
-#define HP100_REG_SL_EARLY 0x1c /* (32) Enhanced Slave Early Rx */
-#define HP100_REG_STAT_DROPPED 0x20 /* R (12) Dropped Packet Counter */
-#define HP100_REG_STAT_ERRORED 0x22 /* R (8) Errored Packet Counter */
-#define HP100_REG_STAT_ABORT 0x23 /* R (8) Abort Counter/OW Coll. Flag */
-#define HP100_REG_RX_RING 0x24 /* W (32) Slave: RX Ring Pointers */
-#define HP100_REG_32_FRAGMENT_LEN 0x28 /* W (13) Slave: Fragment Length Reg */
-#define HP100_REG_32_OFFSET 0x2c /* W (16) Slave: Offset Register */
-
-/* Page 1 - MAC Address/Hash Table */
-
-#define HP100_REG_MAC_ADDR 0x08 /* RW: (8) Cards MAC address */
-#define HP100_REG_HASH_BYTE0 0x10 /* RW: (8) Cards multicast filter */
-
-/* Page 2 - Hardware Mapping */
-
-#define HP100_REG_MEM_MAP_LSW 0x08 /* RW: (16) LSW of cards mem addr */
-#define HP100_REG_MEM_MAP_MSW 0x0a /* RW: (16) MSW of cards mem addr */
-#define HP100_REG_IO_MAP 0x0c /* RW: (8) Cards I/O address */
-#define HP100_REG_IRQ_CHANNEL 0x0d /* RW: (8) IRQ and edge/level int */
-#define HP100_REG_SRAM 0x0e /* RW: (8) How much RAM on card */
-#define HP100_REG_BM 0x0f /* RW: (8) Controls BM functions */
-
-/* New on Page 2 for ETR chips: */
-#define HP100_REG_MODECTRL1 0x10 /* RW: (8) Mode Control 1 */
-#define HP100_REG_MODECTRL2 0x11 /* RW: (8) Mode Control 2 */
-#define HP100_REG_PCICTRL1 0x12 /* RW: (8) PCI Cfg 1 */
-#define HP100_REG_PCICTRL2 0x13 /* RW: (8) PCI Cfg 2 */
-#define HP100_REG_PCIBUSMLAT 0x15 /* RW: (8) PCI Bus Master Latency */
-#define HP100_REG_EARLYTXCFG 0x16 /* RW: (16) Early TX Cfg/Cntrl Reg */
-#define HP100_REG_EARLYRXCFG 0x18 /* RW: (8) Early RX Cfg/Cntrl Reg */
-#define HP100_REG_ISAPNPCFG1 0x1a /* RW: (8) ISA PnP Cfg/Cntrl Reg 1 */
-#define HP100_REG_ISAPNPCFG2 0x1b /* RW: (8) ISA PnP Cfg/Cntrl Reg 2 */
-
-/* Page 3 - EEPROM/Boot ROM */
-
-#define HP100_REG_EEPROM_CTRL 0x08 /* RW: (16) Used to load EEPROM */
-#define HP100_REG_BOOTROM_CTRL 0x0a
-
-/* Page 4 - LAN Configuration (MAC_CTRL) */
-
-#define HP100_REG_10_LAN_CFG_1 0x08 /* RW: (8) Set 10M XCVR functions */
-#define HP100_REG_10_LAN_CFG_2 0x09 /* RW: (8) 10M XCVR functions */
-#define HP100_REG_VG_LAN_CFG_1 0x0a /* RW: (8) Set 100M XCVR functions */
-#define HP100_REG_VG_LAN_CFG_2 0x0b /* RW: (8) 100M LAN Training cfgregs */
-#define HP100_REG_MAC_CFG_1 0x0c /* RW: (8) Types of pkts to accept */
-#define HP100_REG_MAC_CFG_2 0x0d /* RW: (8) Misc MAC functions */
-#define HP100_REG_MAC_CFG_3 0x0e /* RW: (8) Misc MAC functions */
-#define HP100_REG_MAC_CFG_4 0x0f /* R: (8) Misc MAC states */
-#define HP100_REG_DROPPED 0x10 /* R: (16),11:0 Pkts can't fit in mem */
-#define HP100_REG_CRC 0x12 /* R: (8) Pkts with CRC */
-#define HP100_REG_ABORT 0x13 /* R: (8) Aborted Tx pkts */
-#define HP100_REG_TRAIN_REQUEST 0x14 /* RW: (16) Endnode MAC register. */
-#define HP100_REG_TRAIN_ALLOW 0x16 /* R: (16) Hub allowed register */
-
-/* Page 5 - MMU */
-
-#define HP100_REG_RX_MEM_STOP 0x0c /* RW: (16) End of Rx ring addr */
-#define HP100_REG_TX_MEM_STOP 0x0e /* RW: (16) End of Tx ring addr */
-#define HP100_REG_PDL_MEM_STOP 0x10 /* Not used by 802.12 devices */
-#define HP100_REG_ECB_MEM_STOP 0x14 /* I've no idea what this is */
-
-/* Page 6 - Card ID/Physical LAN Address */
-
-#define HP100_REG_BOARD_ID 0x08 /* R: (8) EISA/ISA card ID */
-#define HP100_REG_BOARD_IO_CHCK 0x0c /* R: (8) Added to ID to get FFh */
-#define HP100_REG_SOFT_MODEL 0x0d /* R: (8) Config program defined */
-#define HP100_REG_LAN_ADDR 0x10 /* R: (8) MAC addr of card */
-#define HP100_REG_LAN_ADDR_CHCK 0x16 /* R: (8) Added to addr to get FFh */
-
-/* Page 7 - MMU Current Pointers */
-
-#define HP100_REG_PTR_RXSTART 0x08 /* R: (16) Current begin of Rx ring */
-#define HP100_REG_PTR_RXEND 0x0a /* R: (16) Current end of Rx ring */
-#define HP100_REG_PTR_TXSTART 0x0c /* R: (16) Current begin of Tx ring */
-#define HP100_REG_PTR_TXEND 0x0e /* R: (16) Current end of Rx ring */
-#define HP100_REG_PTR_RPDLSTART 0x10
-#define HP100_REG_PTR_RPDLEND 0x12
-#define HP100_REG_PTR_RINGPTRS 0x14
-#define HP100_REG_PTR_MEMDEBUG 0x1a
-/* ------------------------------------------------------------------------ */
-
-
-/*
- * Hardware ID Register I (Always available, HW_ID, Offset 0x00)
- */
-#define HP100_HW_ID_CASCADE 0x4850 /* Identifies Cascade Chip */
-
-/*
- * Hardware ID Register 2 & Paging Register
- * (Always available, PAGING, Offset 0x02)
- * Bits 15:4 are for the Chip ID
- */
-#define HP100_CHIPID_MASK 0xFFF0
-#define HP100_CHIPID_SHASTA 0x5350 /* Not 802.12 compliant */
- /* EISA BM/SL, MCA16/32 SL, ISA SL */
-#define HP100_CHIPID_RAINIER 0x5360 /* Not 802.12 compliant EISA BM, */
- /* PCI SL, MCA16/32 SL, ISA SL */
-#define HP100_CHIPID_LASSEN 0x5370 /* 802.12 compliant PCI BM, PCI SL */
- /* LRF supported */
-
-/*
- * Option Registers I and II
- * (Always available, OPTION_LSW, Offset 0x04-0x05)
- */
-#define HP100_DEBUG_EN 0x8000 /* 0:Dis., 1:Enable Debug Dump Ptr. */
-#define HP100_RX_HDR 0x4000 /* 0:Dis., 1:Enable putting pkt into */
- /* system mem. before Rx interrupt */
-#define HP100_MMAP_DIS 0x2000 /* 0:Enable, 1:Disable mem.mapping. */
- /* MMAP_DIS must be 0 and MEM_EN */
- /* must be 1 for memory-mapped */
- /* mode to be enabled */
-#define HP100_EE_EN 0x1000 /* 0:Disable,1:Enable EEPROM writing */
-#define HP100_BM_WRITE 0x0800 /* 0:Slave, 1:Bus Master for Tx data */
-#define HP100_BM_READ 0x0400 /* 0:Slave, 1:Bus Master for Rx data */
-#define HP100_TRI_INT 0x0200 /* 0:Don't, 1:Do tri-state the int */
-#define HP100_MEM_EN 0x0040 /* Config program set this to */
- /* 0:Disable, 1:Enable mem map. */
- /* See MMAP_DIS. */
-#define HP100_IO_EN 0x0020 /* 1:Enable I/O transfers */
-#define HP100_BOOT_EN 0x0010 /* 1:Enable boot ROM access */
-#define HP100_FAKE_INT 0x0008 /* 1:int */
-#define HP100_INT_EN 0x0004 /* 1:Enable ints from card */
-#define HP100_HW_RST 0x0002 /* 0:Reset, 1:Out of reset */
- /* NIC reset on 0 to 1 transition */
-
-/*
- * Option Register III
- * (Always available, OPTION_MSW, Offset 0x06)
- */
-#define HP100_PRIORITY_TX 0x0080 /* 1:Do all Tx pkts as priority */
-#define HP100_EE_LOAD 0x0040 /* 1:EEPROM loading, 0 when done */
-#define HP100_ADV_NXT_PKT 0x0004 /* 1:Advance to next pkt in Rx queue */
- /* h/w will set to 0 when done */
-#define HP100_TX_CMD 0x0002 /* 1:Tell h/w download done, h/w */
- /* will set to 0 when done */
-
-/*
- * Interrupt Status Registers I and II
- * (Page PERFORMANCE, IRQ_STATUS, Offset 0x08-0x09)
- * Note: With old chips, these Registers will clear when 1 is written to them
- * with new chips this depends on setting of CLR_ISMODE
- */
-#define HP100_RX_EARLY_INT 0x2000
-#define HP100_RX_PDA_ZERO 0x1000
-#define HP100_RX_PDL_FILL_COMPL 0x0800
-#define HP100_RX_PACKET 0x0400 /* 0:No, 1:Yes pkt has been Rx */
-#define HP100_RX_ERROR 0x0200 /* 0:No, 1:Yes Rx pkt had error */
-#define HP100_TX_PDA_ZERO 0x0020 /* 1 when PDA count goes to zero */
-#define HP100_TX_SPACE_AVAIL 0x0010 /* 0:<8192, 1:>=8192 Tx free bytes */
-#define HP100_TX_COMPLETE 0x0008 /* 0:No, 1:Yes a Tx has completed */
-#define HP100_MISC_ERROR 0x0004 /* 0:No, 1:Lan Link down or bus error */
-#define HP100_TX_ERROR 0x0002 /* 0:No, 1:Yes Tx pkt had error */
-
-/*
- * Xmit Memory Free Count
- * (Page PERFORMANCE, TX_MEM_FREE, Offset 0x14) (Read only, 32bit)
- */
-#define HP100_AUTO_COMPARE 0x80000000 /* Tx Space avail & pkts<255 */
-#define HP100_FREE_SPACE 0x7fffffe0 /* Tx free memory */
-
-/*
- * IRQ Channel
- * (Page HW_MAP, IRQ_CHANNEL, Offset 0x0d)
- */
-#define HP100_ZERO_WAIT_EN 0x80 /* 0:No, 1:Yes asserts NOWS signal */
-#define HP100_IRQ_SCRAMBLE 0x40
-#define HP100_BOND_HP 0x20
-#define HP100_LEVEL_IRQ 0x10 /* 0:Edge, 1:Level type interrupts. */
- /* (Only valid on EISA cards) */
-#define HP100_IRQMASK 0x0F /* Isolate the IRQ bits */
-
-/*
- * SRAM Parameters
- * (Page HW_MAP, SRAM, Offset 0x0e)
- */
-#define HP100_RAM_SIZE_MASK 0xe0 /* AND to get SRAM size index */
-#define HP100_RAM_SIZE_SHIFT 0x05 /* Shift count(put index in lwr bits) */
-
-/*
- * Bus Master Register
- * (Page HW_MAP, BM, Offset 0x0f)
- */
-#define HP100_BM_BURST_RD 0x01 /* EISA only: 1=Use burst trans. fm system */
- /* memory to chip (tx) */
-#define HP100_BM_BURST_WR 0x02 /* EISA only: 1=Use burst trans. fm system */
- /* memory to chip (rx) */
-#define HP100_BM_MASTER 0x04 /* 0:Slave, 1:BM mode */
-#define HP100_BM_PAGE_CK 0x08 /* This bit should be set whenever in */
- /* an EISA system */
-#define HP100_BM_PCI_8CLK 0x40 /* ... cycles 8 clocks apart */
-
-
-/*
- * Mode Control Register I
- * (Page HW_MAP, MODECTRL1, Offset0x10)
- */
-#define HP100_TX_DUALQ 0x10
- /* If set and BM -> dual tx pda queues */
-#define HP100_ISR_CLRMODE 0x02 /* If set ISR will clear all pending */
- /* interrupts on read (etr only?) */
-#define HP100_EE_NOLOAD 0x04 /* Status whether res will be loaded */
- /* from the eeprom */
-#define HP100_TX_CNT_FLG 0x08 /* Controls Early TX Reg Cnt Field */
-#define HP100_PDL_USE3 0x10 /* If set BM engine will read only */
- /* first three data elements of a PDL */
- /* on the first access. */
-#define HP100_BUSTYPE_MASK 0xe0 /* Three bit bus type info */
-
-/*
- * Mode Control Register II
- * (Page HW_MAP, MODECTRL2, Offset0x11)
- */
-#define HP100_EE_MASK 0x0f /* Tell EEPROM circuit not to load */
- /* certain resources */
-#define HP100_DIS_CANCEL 0x20 /* For tx dualq mode operation */
-#define HP100_EN_PDL_WB 0x40 /* 1: Status of PDL completion may be */
- /* written back to system mem */
-#define HP100_EN_BUS_FAIL 0x80 /* Enables bus-fail portion of misc */
- /* interrupt */
-
-/*
- * PCI Configuration and Control Register I
- * (Page HW_MAP, PCICTRL1, Offset 0x12)
- */
-#define HP100_LO_MEM 0x01 /* 1: Mapped Mem requested below 1MB */
-#define HP100_NO_MEM 0x02 /* 1: Disables Req for sysmem to PCI */
- /* bios */
-#define HP100_USE_ISA 0x04 /* 1: isa type decodes will occur */
- /* simultaneously with PCI decodes */
-#define HP100_IRQ_HI_MASK 0xf0 /* pgmed by pci bios */
-#define HP100_PCI_IRQ_HI_MASK 0x78 /* Isolate 4 bits for PCI IRQ */
-
-/*
- * PCI Configuration and Control Register II
- * (Page HW_MAP, PCICTRL2, Offset 0x13)
- */
-#define HP100_RD_LINE_PDL 0x01 /* 1: PCI command Memory Read Line en */
-#define HP100_RD_TX_DATA_MASK 0x06 /* choose PCI memread cmds for TX */
-#define HP100_MWI 0x08 /* 1: en. PCI memory write invalidate */
-#define HP100_ARB_MODE 0x10 /* Select PCI arbitor type */
-#define HP100_STOP_EN 0x20 /* Enables PCI state machine to issue */
- /* pci stop if cascade not ready */
-#define HP100_IGNORE_PAR 0x40 /* 1: PCI state machine ignores parity */
-#define HP100_PCI_RESET 0x80 /* 0->1: Reset PCI block */
-
-/*
- * Early TX Configuration and Control Register
- * (Page HW_MAP, EARLYTXCFG, Offset 0x16)
- */
-#define HP100_EN_EARLY_TX 0x8000 /* 1=Enable Early TX */
-#define HP100_EN_ADAPTIVE 0x4000 /* 1=Enable adaptive mode */
-#define HP100_EN_TX_UR_IRQ 0x2000 /* reserved, must be 0 */
-#define HP100_EN_LOW_TX 0x1000 /* reserved, must be 0 */
-#define HP100_ET_CNT_MASK 0x0fff /* bits 11..0: ET counters */
-
-/*
- * Early RX Configuration and Control Register
- * (Page HW_MAP, EARLYRXCFG, Offset 0x18)
- */
-#define HP100_EN_EARLY_RX 0x80 /* 1=Enable Early RX */
-#define HP100_EN_LOW_RX 0x40 /* reserved, must be 0 */
-#define HP100_RX_TRIP_MASK 0x1f /* bits 4..0: threshold at which the
- * early rx circuit will start the
- * dma of received packet into system
- * memory for BM */
-
-/*
- * Serial Devices Control Register
- * (Page EEPROM_CTRL, EEPROM_CTRL, Offset 0x08)
- */
-#define HP100_EEPROM_LOAD 0x0001 /* 0->1 loads EEPROM into registers. */
- /* When it goes back to 0, load is */
- /* complete. This should take ~600us. */
-
-/*
- * 10MB LAN Control and Configuration Register I
- * (Page MAC_CTRL, 10_LAN_CFG_1, Offset 0x08)
- */
-#define HP100_MAC10_SEL 0xc0 /* Get bits to indicate MAC */
-#define HP100_AUI_SEL 0x20 /* Status of AUI selection */
-#define HP100_LOW_TH 0x10 /* 0:No, 1:Yes allow better cabling */
-#define HP100_LINK_BEAT_DIS 0x08 /* 0:Enable, 1:Disable link beat */
-#define HP100_LINK_BEAT_ST 0x04 /* 0:No, 1:Yes link beat being Rx */
-#define HP100_R_ROL_ST 0x02 /* 0:No, 1:Yes Rx twisted pair has */
- /* been reversed */
-#define HP100_AUI_ST 0x01 /* 0:No, 1:Yes use AUI on TP card */
-
-/*
- * 10 MB LAN Control and Configuration Register II
- * (Page MAC_CTRL, 10_LAN_CFG_2, Offset 0x09)
- */
-#define HP100_SQU_ST 0x01 /* 0:No, 1:Yes collision signal sent */
- /* after Tx.Only used for AUI. */
-#define HP100_FULLDUP 0x02 /* 1: LXT901 XCVR fullduplx enabled */
-#define HP100_DOT3_MAC 0x04 /* 1: DOT 3 Mac sel. unless Autosel */
-
-/*
- * MAC Selection, use with MAC10_SEL bits
- */
-#define HP100_AUTO_SEL_10 0x0 /* Auto select */
-#define HP100_XCVR_LXT901_10 0x1 /* LXT901 10BaseT transceiver */
-#define HP100_XCVR_7213 0x2 /* 7213 transceiver */
-#define HP100_XCVR_82503 0x3 /* 82503 transceiver */
-
-/*
- * 100MB LAN Training Register
- * (Page MAC_CTRL, VG_LAN_CFG_2, Offset 0x0b) (old, pre 802.12)
- */
-#define HP100_FRAME_FORMAT 0x08 /* 0:802.3, 1:802.5 frames */
-#define HP100_BRIDGE 0x04 /* 0:No, 1:Yes tell hub i am a bridge */
-#define HP100_PROM_MODE 0x02 /* 0:No, 1:Yes tell hub card is */
- /* promiscuous */
-#define HP100_REPEATER 0x01 /* 0:No, 1:Yes tell hub MAC wants to */
- /* be a cascaded repeater */
-
-/*
- * 100MB LAN Control and Configuration Register
- * (Page MAC_CTRL, VG_LAN_CFG_1, Offset 0x0a)
- */
-#define HP100_VG_SEL 0x80 /* 0:No, 1:Yes use 100 Mbit MAC */
-#define HP100_LINK_UP_ST 0x40 /* 0:No, 1:Yes endnode logged in */
-#define HP100_LINK_CABLE_ST 0x20 /* 0:No, 1:Yes cable can hear tones */
- /* from hub */
-#define HP100_LOAD_ADDR 0x10 /* 0->1 card addr will be sent */
- /* 100ms later the link status */
- /* bits are valid */
-#define HP100_LINK_CMD 0x08 /* 0->1 link will attempt to log in. */
- /* 100ms later the link status */
- /* bits are valid */
-#define HP100_TRN_DONE 0x04 /* NEW ETR-Chips only: Will be reset */
- /* after LinkUp Cmd is given and set */
- /* when training has completed. */
-#define HP100_LINK_GOOD_ST 0x02 /* 0:No, 1:Yes cable passed training */
-#define HP100_VG_RESET 0x01 /* 0:Yes, 1:No reset the 100VG MAC */
-
-
-/*
- * MAC Configuration Register I
- * (Page MAC_CTRL, MAC_CFG_1, Offset 0x0c)
- */
-#define HP100_RX_IDLE 0x80 /* 0:Yes, 1:No currently receiving pkts */
-#define HP100_TX_IDLE 0x40 /* 0:Yes, 1:No currently Txing pkts */
-#define HP100_RX_EN 0x20 /* 1: allow receiving of pkts */
-#define HP100_TX_EN 0x10 /* 1: allow transmitting of pkts */
-#define HP100_ACC_ERRORED 0x08 /* 0:No, 1:Yes allow Rx of errored pkts */
-#define HP100_ACC_MC 0x04 /* 0:No, 1:Yes allow Rx of multicast pkts */
-#define HP100_ACC_BC 0x02 /* 0:No, 1:Yes allow Rx of broadcast pkts */
-#define HP100_ACC_PHY 0x01 /* 0:No, 1:Yes allow Rx of ALL phys. pkts */
-#define HP100_MAC1MODEMASK 0xf0 /* Hide ACC bits */
-#define HP100_MAC1MODE1 0x00 /* Receive nothing, must also disable RX */
-#define HP100_MAC1MODE2 0x00
-#define HP100_MAC1MODE3 HP100_MAC1MODE2 | HP100_ACC_BC
-#define HP100_MAC1MODE4 HP100_MAC1MODE3 | HP100_ACC_MC
-#define HP100_MAC1MODE5 HP100_MAC1MODE4 /* set mc hash to all ones also */
-#define HP100_MAC1MODE6 HP100_MAC1MODE5 | HP100_ACC_PHY /* Promiscuous */
-/* Note MODE6 will receive all GOOD packets on the LAN. This really needs
- a mode 7 defined to be LAN Analyzer mode, which will receive errored and
- runt packets, and keep the CRC bytes. */
-#define HP100_MAC1MODE7 HP100_MAC1MODE6 | HP100_ACC_ERRORED
-
-/*
- * MAC Configuration Register II
- * (Page MAC_CTRL, MAC_CFG_2, Offset 0x0d)
- */
-#define HP100_TR_MODE 0x80 /* 0:No, 1:Yes support Token Ring formats */
-#define HP100_TX_SAME 0x40 /* 0:No, 1:Yes Tx same packet continuous */
-#define HP100_LBK_XCVR 0x20 /* 0:No, 1:Yes loopback through MAC & */
- /* transceiver */
-#define HP100_LBK_MAC 0x10 /* 0:No, 1:Yes loopback through MAC */
-#define HP100_CRC_I 0x08 /* 0:No, 1:Yes inhibit CRC on Tx packets */
-#define HP100_ACCNA 0x04 /* 1: For 802.5: Accept only token ring
- * group addr that maches NA mask */
-#define HP100_KEEP_CRC 0x02 /* 0:No, 1:Yes keep CRC on Rx packets. */
- /* The length will reflect this. */
-#define HP100_ACCFA 0x01 /* 1: For 802.5: Accept only functional
- * addrs that match FA mask (page1) */
-#define HP100_MAC2MODEMASK 0x02
-#define HP100_MAC2MODE1 0x00
-#define HP100_MAC2MODE2 0x00
-#define HP100_MAC2MODE3 0x00
-#define HP100_MAC2MODE4 0x00
-#define HP100_MAC2MODE5 0x00
-#define HP100_MAC2MODE6 0x00
-#define HP100_MAC2MODE7 KEEP_CRC
-
-/*
- * MAC Configuration Register III
- * (Page MAC_CTRL, MAC_CFG_3, Offset 0x0e)
- */
-#define HP100_PACKET_PACE 0x03 /* Packet Pacing:
- * 00: No packet pacing
- * 01: 8 to 16 uS delay
- * 10: 16 to 32 uS delay
- * 11: 32 to 64 uS delay
- */
-#define HP100_LRF_EN 0x04 /* 1: External LAN Rcv Filter and
- * TCP/IP Checksumming enabled. */
-#define HP100_AUTO_MODE 0x10 /* 1: AutoSelect between 10/100 */
-
-/*
- * MAC Configuration Register IV
- * (Page MAC_CTRL, MAC_CFG_4, Offset 0x0f)
- */
-#define HP100_MAC_SEL_ST 0x01 /* (R): Status of external VGSEL
- * Signal, 1=100VG, 0=10Mbit sel. */
-#define HP100_LINK_FAIL_ST 0x02 /* (R): Status of Link Fail portion
- * of the Misc. Interrupt */
-
-/*
- * 100 MB LAN Training Request/Allowed Registers
- * (Page MAC_CTRL, TRAIN_REQUEST and TRAIN_ALLOW, Offset 0x14-0x16)(ETR parts only)
- */
-#define HP100_MACRQ_REPEATER 0x0001 /* 1: MAC tells HUB it wants to be
- * a cascaded repeater
- * 0: ... wants to be a DTE */
-#define HP100_MACRQ_PROMSC 0x0006 /* 2 bits: Promiscious mode
- * 00: Rcv only unicast packets
- * specifically addr to this
- * endnode
- * 10: Rcv all pckts fwded by
- * the local repeater */
-#define HP100_MACRQ_FRAMEFMT_EITHER 0x0018 /* 11: either format allowed */
-#define HP100_MACRQ_FRAMEFMT_802_3 0x0000 /* 00: 802.3 is requested */
-#define HP100_MACRQ_FRAMEFMT_802_5 0x0010 /* 10: 802.5 format is requested */
-#define HP100_CARD_MACVER 0xe000 /* R: 3 bit Cards 100VG MAC version */
-#define HP100_MALLOW_REPEATER 0x0001 /* If reset, requested access as an
- * end node is allowed */
-#define HP100_MALLOW_PROMSC 0x0004 /* 2 bits: Promiscious mode
- * 00: Rcv only unicast packets
- * specifically addr to this
- * endnode
- * 10: Rcv all pckts fwded by
- * the local repeater */
-#define HP100_MALLOW_FRAMEFMT 0x00e0 /* 2 bits: Frame Format
- * 00: 802.3 format will be used
- * 10: 802.5 format will be used */
-#define HP100_MALLOW_ACCDENIED 0x0400 /* N bit */
-#define HP100_MALLOW_CONFIGURE 0x0f00 /* C bit */
-#define HP100_MALLOW_DUPADDR 0x1000 /* D bit */
-#define HP100_HUB_MACVER 0xe000 /* R: 3 bit 802.12 MAC/RMAC training */
- /* protocol of repeater */
-
-/* ****************************************************************************** */
-
-/*
- * Set/Reset bits
- */
-#define HP100_SET_HB 0x0100 /* 0:Set fields to 0 whose mask is 1 */
-#define HP100_SET_LB 0x0001 /* HB sets upper byte, LB sets lower byte */
-#define HP100_RESET_HB 0x0000 /* For readability when resetting bits */
-#define HP100_RESET_LB 0x0000 /* For readability when resetting bits */
-
-/*
- * Misc. Constants
- */
-#define HP100_LAN_100 100 /* lan_type value for VG */
-#define HP100_LAN_10 10 /* lan_type value for 10BaseT */
-#define HP100_LAN_COAX 9 /* lan_type value for Coax */
-#define HP100_LAN_ERR (-1) /* lan_type value for link down */
-
-/*
- * Bus Master Data Structures ----------------------------------------------
- */
-
-#define MAX_RX_PDL 30 /* Card limit = 31 */
-#define MAX_RX_FRAG 2 /* Don't need more... */
-#define MAX_TX_PDL 29
-#define MAX_TX_FRAG 2 /* Limit = 31 */
-
-/* Define total PDL area size in bytes (should be 4096) */
-/* This is the size of kernel (dma) memory that will be allocated. */
-#define MAX_RINGSIZE ((MAX_RX_FRAG*8+4+4)*MAX_RX_PDL+(MAX_TX_FRAG*8+4+4)*MAX_TX_PDL)+16
-
-/* Ethernet Packet Sizes */
-#define MIN_ETHER_SIZE 60
-#define MAX_ETHER_SIZE 1514 /* Needed for preallocation of */
- /* skb buffer when busmastering */
-
-/* Tx or Rx Ring Entry */
-typedef struct hp100_ring {
- u_int *pdl; /* Address of PDLs PDH, dword before
- * this address is used for rx hdr */
- u_int pdl_paddr; /* Physical address of PDL */
- struct sk_buff *skb;
- struct hp100_ring *next;
-} hp100_ring_t;
-
-
-
-/* Mask for Header Descriptor */
-#define HP100_PKT_LEN_MASK 0x1FFF /* AND with RxLength to get length */
-
-
-/* Receive Packet Status. Note, the error bits are only valid if ACC_ERRORED
- bit in the MAC Configuration Register 1 is set. */
-#define HP100_RX_PRI 0x8000 /* 0:No, 1:Yes packet is priority */
-#define HP100_SDF_ERR 0x4000 /* 0:No, 1:Yes start of frame error */
-#define HP100_SKEW_ERR 0x2000 /* 0:No, 1:Yes skew out of range */
-#define HP100_BAD_SYMBOL_ERR 0x1000 /* 0:No, 1:Yes invalid symbol received */
-#define HP100_RCV_IPM_ERR 0x0800 /* 0:No, 1:Yes pkt had an invalid packet */
- /* marker */
-#define HP100_SYMBOL_BAL_ERR 0x0400 /* 0:No, 1:Yes symbol balance error */
-#define HP100_VG_ALN_ERR 0x0200 /* 0:No, 1:Yes non-octet received */
-#define HP100_TRUNC_ERR 0x0100 /* 0:No, 1:Yes the packet was truncated */
-#define HP100_RUNT_ERR 0x0040 /* 0:No, 1:Yes pkt length < Min Pkt */
- /* Length Reg. */
-#define HP100_ALN_ERR 0x0010 /* 0:No, 1:Yes align error. */
-#define HP100_CRC_ERR 0x0008 /* 0:No, 1:Yes CRC occurred. */
-
-/* The last three bits indicate the type of destination address */
-
-#define HP100_MULTI_ADDR_HASH 0x0006 /* 110: Addr multicast, matched hash */
-#define HP100_BROADCAST_ADDR 0x0003 /* x11: Addr broadcast */
-#define HP100_MULTI_ADDR_NO_HASH 0x0002 /* 010: Addr multicast, didn't match hash */
-#define HP100_PHYS_ADDR_MATCH 0x0001 /* x01: Addr was physical and mine */
-#define HP100_PHYS_ADDR_NO_MATCH 0x0000 /* x00: Addr was physical but not mine */
-
-/*
- * macros
- */
-
-#define hp100_inb( reg ) \
- inb( ioaddr + HP100_REG_##reg )
-#define hp100_inw( reg ) \
- inw( ioaddr + HP100_REG_##reg )
-#define hp100_inl( reg ) \
- inl( ioaddr + HP100_REG_##reg )
-#define hp100_outb( data, reg ) \
- outb( data, ioaddr + HP100_REG_##reg )
-#define hp100_outw( data, reg ) \
- outw( data, ioaddr + HP100_REG_##reg )
-#define hp100_outl( data, reg ) \
- outl( data, ioaddr + HP100_REG_##reg )
-#define hp100_orb( data, reg ) \
- outb( inb( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg )
-#define hp100_orw( data, reg ) \
- outw( inw( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg )
-#define hp100_andb( data, reg ) \
- outb( inb( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg )
-#define hp100_andw( data, reg ) \
- outw( inw( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg )
-
-#define hp100_page( page ) \
- outw( HP100_PAGE_##page, ioaddr + HP100_REG_PAGING )
-#define hp100_ints_off() \
- outw( HP100_INT_EN | HP100_RESET_LB, ioaddr + HP100_REG_OPTION_LSW )
-#define hp100_ints_on() \
- outw( HP100_INT_EN | HP100_SET_LB, ioaddr + HP100_REG_OPTION_LSW )
-#define hp100_mem_map_enable() \
- outw( HP100_MMAP_DIS | HP100_RESET_HB, ioaddr + HP100_REG_OPTION_LSW )
-#define hp100_mem_map_disable() \
- outw( HP100_MMAP_DIS | HP100_SET_HB, ioaddr + HP100_REG_OPTION_LSW )
projects / linux-2.6-microblaze.git / commitdiff